Christie Digital Systems Projector 103 002001 User Manual

103-002001  
MODEL  
User's Manual  
DRAFT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
All the safety and operating instructions should be read before  
the product is operated.  
This projector should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supplied, consult your authorized dealer or  
local power company.  
Read all of the instructions given here and retain them for later  
use. Unplug this projector from AC power supply before  
cleaning. Do not use liquid or aerosol cleaners. Use a damp  
cloth for cleaning.  
Do not overload wall outlets and extension cords as this can  
result in fire or electric shock. Do not allow anything to rest on  
the power cord. Do not locate this projector where the cord  
may be damaged by persons walking on it.  
Follow all warnings and instructions marked on the projector.  
For added protection to the projector during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet. This will prevent damage  
due to lightning and power line surges.  
Do not attempt to service this projector yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
Unplug this projector from wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool, etc...  
Do not use attachments not recommended by the  
manufacturer as they may cause hazards.  
c. If the projector has been exposed to rain or water.  
d. If the projector does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the projector to normal operation.  
e. If the projector has been dropped or the cabinet has been  
damaged.  
f. When the projector exhibits a distinct change in  
performance-this indicates a need for service.  
Do not place this projector on an unstable cart, stand, or table.  
The projector may fall, causing serious injury to a child or  
adult, and serious damage to the projector. Use only with a  
cart or stand recommended by the manufacturer, or sold with  
the projector. Wall or shelf mounting should follow the  
manufacturer's instructions, and should use a mounting kit  
approved by the manufacturers.  
An appliance and cart combination should  
be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the appliance and cart  
combination to overturn.  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer that have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock, or injury to persons.  
Upon completion of any service or repairs to this projector, ask  
the service technician to perform routine safety checks to  
determine that the projector is in safe operating condition.  
Slots and openings in the back and bottom of the cabinet are  
provided for ventilation, to insure reliable operation of the  
equipment and to protect it from overheating.  
The openings should never be covered with cloth or other  
materials, and the bottom opening should not be blocked by  
placing the projector on a bed, sofa, rug, or other similar  
surface. This projector should never be placed near or over a  
radiator or heat register.  
This projector should not be placed in a built-in installation  
such as a book case unless proper ventilation is provided.  
Voor de klanten in Nederland  
Bij dit product zijn batterijen  
geleverd.  
Wanneer deze leeg zijn,  
moet u ze niet weggooien  
maar inleveren als KCA.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the projector.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPLIANCES  
Federal Communication Commission Notice  
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures :  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such  
changes or modifications should be made, you could be required to stop operation of the equipment.  
Model Number  
Trade Name  
Responsible party  
Address  
: 103-002001  
: Christie  
: CHRISTIE DIGITAL SYSTEMS, Inc.  
: 10550 Camden Drive Cypress, CA 90630 USA  
: (714) 236-8610  
Telephone No.  
AC POWER CORD REQUIREMENT  
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada :  
AC Power Cord used in the United States and Canada is listed by the Underwriters  
Laboratories (UL) and certified by the Canadian Standard Association (CSA).  
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the  
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be  
unable to insert the plug into the outlet, contact your electrician.  
GROUND  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
FEATURES AND DESIGN  
6
7
COMPUTER INPUT  
22  
SELECTING INPUT SOURCE  
22  
23  
24  
SELECTING COMPUTER SYSTEM  
PREPARATION  
COMPATIBLE COMPUTER SPECIFICATIONS  
PC ADJUSTMENT  
25  
25  
26  
AUTO PC ADJUSTMENT  
MANUAL PC ADJUSTMENT  
NAME OF EACH PART OF PROJECTOR  
7
8
8
9
10  
10  
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
POSITIONING PROJECTOR  
ADJUSTABLE FEET  
PICTURE IMAGE ADJUSTMENTS  
IMAGE LEVEL SELECT  
28  
28  
29  
IMAGE LEVEL ADJUSTMENT  
MOVING PROJECTOR  
PICTURE SCREEN ADJUSTMENT  
30  
VIDEO INPUT  
31  
CONNECTING PROJECTOR  
11  
SELECTING INPUT SOURCE  
SELECTING VIDEO SYSTEM  
31  
32  
33  
33  
34  
TERMINALS OF PROJECTOR  
CONNECTING TO COMPUTER  
CONNECTING TO VIDEO EQUIPMENT  
11  
12  
13  
PICTURE IMAGE ADJUSTMENTS  
IMAGE LEVEL SELECT  
IMAGE LEVEL ADJUSTMENT  
PICTURE SCREEN ADJUSTMENT  
35  
BEFORE OPERATION  
14  
OPERATION OF REMOTE CONTROL UNIT  
LASER POINTER FUNCTION  
14  
14  
15  
SETTING  
36  
REMOTE CONTROL BATTERIES INSTALLATION  
SETTING MENU  
36  
TOP CONTROLS AND INDICATORS  
16  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
17  
17  
17  
18  
APPENDIX  
38  
LAMP REPLACEMENT  
LAMP REPLACE  
38  
38  
39  
BASIC OPERATION  
19  
LAMP REPLACE COUNTER  
OPERATING WIRELESS MOUSE  
40  
MAINTENANCE  
41  
41  
41  
41  
TURNING ON / OFF PROJECTOR  
19  
WARNING TEMP. INDICATOR  
AIR FILTER CARE AND CLEANING  
CLEANING PROJECTION LENS  
ADJUSTING SCREEN  
20  
20  
20  
20  
20  
21  
21  
21  
ZOOM ADJUSTMENT  
FOCUS ADJUSTMENT  
LENS SHIFT ADJUSTMENT  
KEYSTONE ADJUSTMENT  
PICTURE FREEZE FUNCTION  
NO SHOW FUNCTION  
TROUBLESHOOTING  
42  
TECHNICAL SPECIFICATIONS  
CONFIGURATIONS OF TERMINALS  
OPTIONAL PARTS  
44  
45  
46  
P-TIMER FUNCTION  
SOUND ADJUSTMENT  
21  
TRADEMARKS  
G Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.  
G IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.  
G Windows and PowerPoint are registered trademarks of Microsoft Corporation.  
G Each name of corporations or products in the user's manual is a trademark or a registered trademark of its  
respective corporation.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES AND DESIGN  
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This  
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)  
technology.  
N Motor-driven Lens Shift  
N Compact Design  
Projection lens can be moved up and down with motor-  
driven lens shift function. This function makes it easy to  
provide projected image where you want.  
Zoom and focus can be also adjusted with motor-driven  
operation.  
This projector is extremely compact in size and weight.  
It is designed to carry and work anywhere you wish to  
use.  
N Compatibility  
This projector widely accepts various video and  
computer input signals including;  
N Keystone Correction  
G Computers  
Positioning of a projector may result in distorted image  
being displayed in a trapezoid shape. Keystone  
Correction solves this problem by digitally altering  
projection to produce undistorted images.  
IBM-compatible or Macintosh computer up to 1280  
x 1024 resolution.  
G 6 Color Systems  
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-  
N color system can be connected.  
N Power Management  
G Component Video  
Power Management function is provided to reduce power  
consumption while a projector is not in use.  
Component video signal, such as a DVD player  
output high definition TV signals including 480i,  
480p, 575i, 575p, 720p, 1035i or 1080i, can be  
connected.  
This Power Management function operates to turn  
Projection Lamp off when a projector detects signal  
interruption and any button is not pressed over 5  
minutes. Projection Lamp is automatically turned on  
again when a projector detects signal or any operation  
button is pressed.  
G S-Video  
S-Video signal, such as a S-VHS VCR output  
signal, can be connected.  
This projector is shipped with this function ON.  
N High Resolution Image  
N Digital Visual Interface  
This projector provides 1024 x 768 dots resolution for  
computer input and 800 horizontal TV lines. Resolution  
from a computer between XGA (1024 x 768) and SXGA  
(1280 x 1024) is compressed into 1024 x 768 dots. This  
projector cannot display image of over 1280 x 1024 dots.  
When resolution of your computer is more than 1280 x  
1024, reset a computer output for lower resolution.  
This projector is equipped with DVI 29-pin terminal for  
connecting DVI output from a computer.  
N Laser Pointer Function  
Remote Control Unit supplied with this projector includes  
Laser Pointer function. This function helps you to make  
a smart presentation on a projected screen.  
N Multi-Scan System  
This projector has Multi-Scan System to conform to  
almost all computer output signals quickly. There is no  
need for troublesome manual adjustment of frequency  
and other settings.  
N Wireless Mouse  
Remote Control Unit supplied with this projector has  
Wireless Mouse function for a connected computer. This  
function enables you to operate both projector and  
computer with Remote Control Unit only.  
N Progressive Scan Function  
This function converts interlace video signals into  
progressive scan signals and provide fine picture quality.  
N Multilanguage Menu Display  
Operation menu is displayed in; English, German,  
French, Italian, Spanish, Portuguese, Dutch, Swedish,  
Russian, Chinese, Korean or Japanese.  
N One-Touch Auto PC Adjustment  
Incoming computer video signals are recognized and the  
best adjustment is automatically set by Auto PC  
Adjustment. No complicated setup is necessary and  
projection is always precise.  
N Digital Zoom (for Computer)  
Digital Zoom function adjusts the image size to approx.  
1/4 ~ 49 times of original image size, allowing you to  
focus on crucial information at a presentation.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
NAME OF EACH PART OF PROJECTOR  
FRONT  
TOP CONTROLS  
AND INDICATORS  
INFRARED  
REMOTE RECEIVER  
PROJECTION LENS  
SPEAKERS  
LENS COVER  
AIR INTAKE VENT  
TERMINALS  
AND CONNECTORS  
INFRARED  
REMOTE RECEIVER  
AIR INTAKE VENT  
BACK  
EXHAUST VENTS  
HOT AIR EXHAUSTED !  
Air blown from Exhaust Vents is hot.  
When using or installing projector,  
following precautions should be taken.  
G Do not put any flammable object near  
this vent.  
G Keep side grill at least 3(1m) away from  
any object, especially heat-sensitive  
object.  
G Do not touch this area, especially screw  
and metallic part. This area will become  
hot while a projector is used.  
CARRY HANDLE  
This projector detects internal  
temperature and automatically controls  
operating power of Cooling Fans.  
POWER CORD CONNECTOR  
BOTTOM  
AIR INTAKE VENTS  
This projector is equipped with Cooling  
Fans for protection from overheating.  
Pay attention to the following to ensure  
proper ventilation and avoid a possible  
risk of fire and malfunction.  
ADJUSTABLE FEET  
AND  
FEET LOCK LATCHES  
G Do not cover vent slots.  
G Keep side and bottom clear of any  
object. Obstructions may block  
cooling air.  
LAMP COVER  
AIR FILTERS  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
This projector uses nominal input voltages of 100-120 V or 200-240  
V AC. This projector automatically selects the correct input  
voltage. It is designed to work with single-phase power systems  
having a grounded neutral conductor. To reduce risk of electrical  
shock, do not plug into any other type of power system.  
Consult your authorized dealer or service station if you are not sure  
of the type of power supply being in use.  
Connect a projector with a peripheral equipment before turning a  
projector on. (Refer to pages 11 ~ 13 for connection.)  
CAUTION  
For safety, unplug AC Power Cord when an appliance is not  
used.  
When this projector is connected to the outlet with AC Power  
Cord, an appliance is in Stand-by Mode and consumes a little  
electric power.  
Connect AC Power Cord (supplied) to a projector.  
The AC outlet must be near this equipment and  
must be easily accessible.  
CAUTION  
The AC Power Cord must meet the requirement of the country where you use the projector.  
Confirm the AC plug type with the chart below. The proper AC Power Cord must be used.  
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.  
Projector side  
AC Outlet side  
For U.S.A. and Canada  
For Continental Europe  
Ground  
To POWER CORD  
CONNECTOR on the  
projector.  
To AC Outlet.  
(120 V AC)  
To AC Outlet.  
(200 - 240 V AC)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
POSITIONING PROJECTOR  
G This projector is designed to project on a flat  
ROOM LIGHT  
projection surface.  
G Projector can be focused from 4.1(1.2m) ~ 32.8’  
(10.0m).  
Brightness in room has a great influence on  
picture quality. It is recommended to limit  
ambient lighting in order to provide best  
image.  
G Refer to figure below to adjust screen size.  
32.8(10.0m)  
22.0(6.7m)  
300”  
Max. Zoom  
Min. Zoom  
16.4(5.0m)  
200”  
154”  
10.8(3.3m)  
4.1(1.2m)  
231”  
150”  
115”  
100”  
77”  
39”  
30”  
Max. Zoom  
Min. Zoom  
39”  
30”  
100”  
77”  
150”  
115”  
200”  
250”  
192”  
300”  
231”  
Screen  
Size  
154”  
4.1(1.2m)  
10.8(3.3m)  
16.4(5.0m)  
22.0(6.7m)  
27.6(8.4m) 32.8(10.0m)  
Distance  
LENS SHIFT ADJUSTMENT  
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to  
provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer  
to P 20 for operation.  
Highest (10 : 0)  
Lowest (1 : 1)  
1
1
10 : 0  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
ADJUSTABLE FEET  
Picture tilt and projection angle can be adjusted by rotating  
ADJUSTABLE FEET. Projection angle can be adjusted to 10  
degrees.  
Lift the front of a projector and pull FEET LOCK LATCHES  
on the both sides of a projector.  
1
Release FEET LOCK LATCHES to lock ADJUSTABLE FEET  
and rotate ADJUSTABLE FEET to fine tune position and tilt.  
2
To retract ADJUSTABLE FEET, lift the front of a projector  
and pull and undo FEET LOCK LATCHES.  
Keystone distortion of a projected image can be adjusted by  
Menu Operation. (Refer to P20 and 36.)  
3
NOTE :  
THIS PROJECTOR SHOULD BE SET IN THE WAY  
INDICATED. PROJECTION LAMP MAY MALFUNCTION.  
FEET LOCK  
LATCHES  
ADJUSTABLE FEET  
MOVING PROJECTOR  
Use Carry Handle when moving a projector.  
When moving a projector, replace Lens Cover and retract  
Adjustable Feet to prevent damage to the lens and cabinet.  
When a projector is not in use for an extended period, put it into  
the case (dust cover) supplied with a projector.  
CAUTION  
Dust Cover (supplied) is intended for protection from dust and  
scratches on the surface of a cabinet, and it is not designed to  
protect an appliance from external forces. Do not transport a  
projector through a courier or transport services with this cover.  
The projector can be damaged. When handling a projector, do not  
drop, bump, subject it to strong forces or put other things on the  
cabinet.  
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR  
G Do not drop or bump a projector, otherwise damages or malfunctions may result.  
G When carrying a projector, use a suitable carrying case.  
G Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause  
damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best  
way.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
TERMINALS OF PROJECTOR  
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on  
pages 11 to 13 and connect properly.  
MONITOR OUTPUT  
TERMINAL  
Connect a monitor to Connect computer output  
this terminal. (Analog HDB 15-pin type) or  
This terminal outputs a 21-pin Scart (RGB) output these jacks.  
computer input signal from video equipment to this (Refer to P12.)  
(except Digital signal terminal. (Refer to P12, 13.)  
input on DVI terminal).  
COMPUTER INPUT 1  
TERMINAL  
COMPUTER AUDIO  
INPUT (1 and 2) JACKS  
Connect an audio output  
(stereo) from computer to  
COMPUTER INPUT 2 (DIGITAL/ANALOG)  
Media Card Imager / Wireless Imager  
TERMINAL  
Connect computer output  
(Digital / Analog DVI-I type),  
Media Card Imager*, or Wireless  
Imager* to this terminal. (Refer to  
P12)  
(Refer to P12.)  
*optional accessories  
RESET BUTTON  
This projector uses a micro  
processor to control this unit,  
and occasionally, this micro  
processor may malfunction  
and need to be reset. This  
can be done by pressing  
RESET button with a pen,  
which will shut down and  
restart the unit. Do not use  
RESET function excessively.  
COMPUTER IN 1  
AUDIO IN 1  
AUDIO IN 2  
AUDIO OUT  
COMPUTER IN 2  
DVI - I  
RESET  
CONTROL PORT  
AUDIO OUTPUT JACK  
Connect an external  
audio amplifier to this  
jack.  
MONITOR OUT  
(MONO)  
CONTROL PORT CONNECTOR  
S – VIDEO  
USB  
R – AUDIO IN – L  
VIDEO  
When controlling the computer  
with Remote Control Unit of  
this projector, connect the  
mouse port of your personal  
computer to this connector.  
(Refer to P12.)  
(Refer to P12, 13.)  
MCI / WI  
Pb / Cb – Pr / Cr  
Y
Do not press this button.  
This button is used for our  
optional accessories.  
S-VIDEO INPUT JACK  
Connect the S-VIDEO  
output from video  
equipment to this  
jack. (Refer to P13.)  
AUDIO INPUT JACKS  
VIDEO INPUT JACKS  
VIDEO INPUT JACK  
USB CONNECTOR (Series B)  
Connect the audio output  
from video equipment to  
these jacks.  
Connect the component  
video output from video  
equipment to connect the  
component video outputs to  
Y, Pb/Cb and Pr/Cr jacks.  
(Refer to P13.)  
Connect the composite  
video output from video  
equipment to connect  
this jack.  
When controlling the computer  
with Remote Control Unit of this  
projector, connect USB port of  
your personal computer to this  
connector. (Refer to P12.)  
(Refer to P13.)  
G When the audio output  
is monaural, connect it  
to L (MONO) jack.  
(Refer to P13.)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO COMPUTER  
Cables used for connection (= Cable or adapter is not supplied with this projector.)  
VGA Cable (HDB 15 pin)  
USB Cable  
Control Cable for SERIAL Port  
DVI-Digital Cable (for Single Link T.M.D.S.)  
Control Cable for PS2 Port , or ADB Port ✽  
MAC Adapter (When connecting to Macintosh computer)  
DVI/VGA Adapter  
Audio Cables {Mini Plug (stereo) x 2} ✽  
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)  
Desktop type  
Laptop type  
Monitor Output  
PS/2 port  
ADB port  
Monitor Input Audio Output  
USB port Serial port  
MAC Adapter  
Set slide switches  
according to the  
chart below.  
Control Cable  
Control Cable  
Control Cable  
for Serial Port  
Audio  
Cable  
(stereo)  
for PS/2 Port for ADB Port ✽  
VGA  
Cable ✽  
USB  
Cable  
DVI Cable ✽  
Terminal  
Terminal  
Terminal  
VGA Cable  
COMPUTER IN 2 DVI-I  
COMPUTER  
AUDIO IN  
MONITOR OUT  
USB  
Use one of these Control  
Cables corresponding with  
the terminal of your  
computer.  
COMPUTER IN 1  
DVI/VGA  
COMPUTER IN 1  
AUO IN 1  
Adapter  
COMPUTER IN 2  
DVI - I  
RESET  
ADIO IN 2  
AUDIO OUT  
CONTROL PORT  
S VIDEO  
USB  
CONTROL PORT  
COMPUTER IN 2 DVI-I  
MONITOR OUT  
(MONO)  
R AUDIO IN L  
VIDEO  
MCI / WI  
Pb / Cb Pr / Cr  
Y
Terminals  
of the Projector  
AUDIO OUT  
NOTE :  
When connecting the cable, the power  
cords of both the projector and the external  
equipment should be disconnected from  
AC outlet. Turn the projector and  
peripheral equipment on before the  
computer is switched on.  
Audio Cable  
(stereo) ✽  
N MAC ADAPTER (Not supplied)  
Set switches as shown in the table ON  
below depending on RESOLU-  
TION MODE that you want to use  
ON  
DIP  
Audio Input  
1
2
3
4
5
6
before you turn on projector and  
computer.  
External Audio Equipment  
Audio Speaker  
OFF  
1
2
3
4
5
6
Audio Amplifier  
(stereo)  
13" MODE (640 x 480)  
ON  
ON OFF OFF OFF OFF  
16" MODE (832 x 624) OFF ON OFF ON OFF OFF  
19" MODE (1024 x 768) OFF ON  
21" MODE (1152 x 870) ON ON  
ON OFF OFF OFF  
ON ON OFF OFF  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO VIDEO EQUIPMENT  
Cables used for connection (= Cable is not supplied with this projector.)  
Video Cable (RCA x 1 or RCA x 3) ✽  
S-VIDEO Cable ✽  
Audio Cable {Mini Plug (stereo)} ✽  
Scart Cable ✽  
Audio Cable (RCA x 2) ✽  
Video Source (example)  
Video Cassette Recorder  
Component video output equipment.  
(such as DVD player or high-definition TV source.)  
Video Disc Player  
Composite  
Video Output  
Audio Output  
RGB Scart  
21-pin Output  
Component Video Output  
(Y, Pb/Cb, Pr/Cr)  
S-VIDEO Output  
(R, L)  
Video Cable  
(RCA x 3)  
Audio Cable  
(RCA x 2) ✽  
Video Cable  
(RCA x 1) ✽  
S-VIDEO  
Cable ✽  
Scart Cable ✽  
VIDEO  
S-VIDEO  
AUDIO IN  
Y - Pb/Cb - Pr/Cr  
COMPUTER IN 1  
AUDIO IN 1  
AUDIO IN 2  
AUDIO OUT  
COMPUTER IN 2  
DVI - I  
COMPUTER IN 1  
RESET  
CONTROL PORT  
MONITOR OUT  
(MONO)  
S VIDEO  
R AUDIO L  
VEO  
Use any of VIDEO jack, S-VIDEO  
jack, or Y-Pb/Cb-Pr/Cr jacks.  
When both VIDEO jack and S-  
VIDEO jack are connected, S-  
VIDEO jack has priority over  
VIDEO jack.  
MCI / WI  
Pb / Cb Pr / Cr  
Y
USB  
Terminals  
of the Projector  
When both Y-Pb/Cb-Pr/Cr jacks  
and S-VIDEO jack are connected,  
Y-Pb/Cb-Pr/Cr jacks has priority  
over S-VIDEO jack.  
AUDIO OUT  
Audio Cable  
(Stereo) ✽  
Audio Input  
NOTE :  
External Audio Equipment  
Audio Speaker  
(stereo)  
When connecting the cable, the power  
cords of both the projector and the external  
equipment should be disconnected from  
AC outlet.  
Audio Amplifier  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
OPERATION OF REMOTE CONTROL  
LASER POINTER (Drag ON)  
INDICATOR  
Lights red while laser beam  
is emitted from Laser Light  
Window.  
Left Side  
POWER ON-OFF BUTTON  
Used to turn projector on or  
off. (P19)  
AUTO PC ON-OFF  
Lights green when drag ON  
position. (P40)  
D.ZOOM FREEZE NO SHOW  
AUTO PC ADJ. BUTTON  
Use to operate AUTO PC  
Adjustment function. (P25)  
MUTE  
IMAGE  
MUTE BUTTON  
Used to mute sound. (P21)  
VOLUME  
-
VOLUME+  
SELECT  
IMAGE BUTTON  
Used to select image  
level. (P28, 33)  
MENU  
KEYSTONE  
DRAG ON/OFF BUTTON  
Used to select drag ON/OFF  
position. (P40)  
ALL-OFF SWITCH  
KEYSTONE BUTTON  
Used to correct keystone  
distortion. (P20, 36)  
When using Remote Control Unit,  
turn this switch to ON.And turn it  
to ALL OFFwhen it is not used.  
LEFT CLICK BUTTON  
Used as a PC mouse in  
Wireless Mouse Operation.  
Press this button and the  
mouse pointer button to drag  
a selected screen object.  
(P40)  
INSIDE THE BATTERY  
COMPARTMENT BOX  
This remote control provide the DIP  
switches into the battery compartment  
box.  
Slide the SW4 (LASER ON/OFF  
switch) to "OFF" position. The laser  
pointer function is not operated.  
Set switches 1-3 as shown in table  
below depending on Code No. that you  
want to select remote control code.  
(Refer to P37.)  
MOUSE POINTER  
Used as a PC mouse in  
Wireless Mouse Operation.  
(P40)  
LASER  
RIGHT CLICK BUTTON  
LASER BUTTON  
P-TIMERCOMPUTER  
1
Used as a PC mouse in  
Wireless Mouse Operation.  
(P40)  
Used to operate Laser Pointer  
Function. Laser beam is  
emitted while pressing this  
button within 1 minute.  
ZOOM  
COMPUTER  
VIDEO  
2
When using this Laser Pointer  
for more than  
1
minute,  
FOCUS LENS  
release LASER button and  
press it again.  
DIP SWITCH SETTING  
SW4 ........ LASER ON/OFF  
SW1 SW2 SW3 Code No.  
LENS SHIFT BUTTON  
Used to select LENS  
SHIFT function. (P20)  
ON  
ON  
ON  
ON  
ON  
OFF ON  
ON  
Code 1  
Code 2  
Code 3  
FOCUS BUTTON  
Used to adjust focus. (P20)  
OFF  
ON  
OFF OFF  
Code 4  
Code 5  
Code 6  
Code 7  
Code 8  
OFF ON  
OFF ON  
ON  
OFF  
OFF OFF ON  
OFF OFF OFF  
LASER POINTER FUNCTION  
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is  
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,  
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being  
emitted.  
Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other  
people. Three marks below are caution labels for laser beam.  
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result  
hazardous radiation exposure.  
These caution labels are put on remote control.  
LASER POINTER INDICATOR  
Laser Light Window  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
NO SHOW BUTTON  
Used to turn picture into  
black image. (P21)  
D.ZOOM BUTTON  
Operating Range  
Used to select DIGITAL  
ZOOM +/mode and  
resize image. (P30)  
AUTO PC ON-OFF  
Point Remote Control Unit toward  
projector (Receiver Window)  
whenever pressing any button.  
Maximum operating range for  
Remote Control Unit is about 16.4’  
(5m) and 60° in front and rear of a  
projector.  
D.ZOOM FREEZE NO SHOW  
SELECT BUTTON  
MUTE  
IMAGE  
FREEZE BUTTON  
Used to freeze picture. (P21)  
Used to execute item  
selected, or to expand or  
compress image in  
DIGITAL ZOOM +/- mode.  
(P30)  
VOLUME  
-
VOLUME+  
SELECT  
POINT (VOLUME +/-)  
BUTTONS  
MENU  
KEYSTONE  
Used to select an item or  
adjust value in ON-SCREEN  
MENU. They are also used  
to pan image in DIGITAL  
ZOOM +/- mode. (P30)  
POINT LEFT/RIGHT buttons  
are also used as VOLUME  
+/- buttons. (P21)  
MENU BUTTON  
Used to select MENU  
operation. (P17, 18)  
60°  
16.4’  
(5 m)  
P-TIMER BUTTON  
LASER  
COMPUTER 1 BUTTON  
Used to operate P-  
TIMER function. (P21)  
Used to select input  
source (COMPUTER 1).  
(P22)  
P-TIMERCOMPUTER  
1
ZOOM  
COMPUTER  
VIDEO  
2
ZOOM BUTTON  
COMPUTER 2 BUTTON  
Used to adjust zoom. (P20)  
Used to select input  
source (COMPUTER 2).  
(P22, 31)  
FOCUS LENS  
16.4’  
(5 m)  
VIDEO BUTTON  
60°  
Used to select input  
source (VIDEO). (P31)  
Remote Control Batteries Installation  
Remove battery  
compartment lid.  
Slide batteries into  
compartment.  
Replace compartment lid.  
1
2
3
Two AA size batteries  
Press lid down-  
ward and slide it.  
For correct polarity (+ and  
), be sure battery  
terminals are in contact  
with pins in compartment.  
To insure safe operation, please observe following precautions :  
G Use (2) AA, UM3 or R06 type alkaline batteries.  
G Replace two batteries at same time.  
G Do not use a new battery with an used battery.  
G Avoid contact with water or liquid.  
G Do not expose Remote Control Unit to moisture, or heat.  
G Do not drop Remote Control Unit.  
G If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.  
G Danger of explosion if battery is incorrectly replaced.  
G Dispose of used batteries according to batteries manufacturers instructions and local rules.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
TOP CONTROLS AND INDICATORS  
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.  
TOP CONTROLS  
AND INDICATORS  
LAMP REPLACE INDICATOR  
LAMP INDICATOR  
WARNING TEMP. INDICATOR  
READY INDICATOR  
Turns yellow when the  
life of the projection  
lamp draws to an end.  
(P38)  
Becomes dim when the  
projector is turned on.  
And it is bright when  
the projector is in  
stand-by mode.  
Flashes red when  
Lights  
green when the  
internal  
projector  
projector is ready to be turned  
on. And it flashes green in  
Power Management mode.  
(P37)  
temperature is too  
high. (P41)  
POWER ONOFF BUTTON  
Used to turn the projector  
on or off. (P19)  
POINT (VOLUME + / ) BUTTONS  
Used to select an item or adjust  
value in ON-SCREEN MENU.  
They are also used to pan the  
image in DIGITAL ZOOM +/–  
mode. (P30)  
POINT LEFT/RIGHT buttons are  
also used as VOLUME +/–  
buttons. (P21)  
SELECT BUTTON  
Used to execute the item  
selected. It is also used  
to expand / compress  
the image in DIGITAL  
ZOOM mode. (P30)  
ON-OFF  
SELECT  
MENU BUTTON  
INPUT BUTTON  
Used to select input  
source. (P22, 31)  
Used to open or close  
MENU operation. (P17,  
18)  
IMAGE BUTTON  
Used to select image  
level. (P28, 33)  
AUTO PC ADJ. BUTTON  
Use to operate AUTO PC  
Adjustment function. (P25)  
KEYSTONE  
ZOOM BUTTON  
KEYSTONE BUTTON  
Used to adjust zoom.  
(P20)  
Used to correct keystone  
distortion. (P20, 36)  
LENS SHIFT BUTTON  
Used to select LENS  
SHIFT function. (P20)  
FOCUS BUTTON  
Used to adjust focus.  
(P20)  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
REMOTE CONTROL UNIT  
You can control and adjust this projector through ON-SCREEN  
MENU. Refer to the following pages to operate each adjustment  
on ON-SCREEN MENU.  
AUTO PC ON-OFF  
1 DISPLAY MENU  
Press MENU button to display ON-SCREEN MENU.  
POINT BUTTONS  
D.ZOOM FREEZE NO SHOW  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
MUTE  
IMAGE  
2 MOVING POINTER  
VOLUME  
-
VOLUME+  
SELECT  
Move the pointer (see below) or adjust the value of item by  
pressing POINT button(s) on Top Control or on Remote Control  
Unit.  
MENU  
KEYSTONE  
Pointer is the icon on ON-SCREEN MENU to select the item.  
See the figures on the section "FLOW OF ON-SCREEN MENU  
OPERATION" below.  
SELECT BUTTON  
Used to select the item.  
TOP CONTROL  
3 SELECT ITEM  
Select the item or set selected function by pressing SELECT  
button.  
SELECT  
POINT BUTTONS  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
KEYSTONE  
SELECT BUTTON  
Used to select the item.  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
MENU ICON  
Display ON-SCREEN MENU  
Press MENU button to display ON-SCREEN MENU (MENU  
BAR). A red frame is POINTER.  
1
POINTER  
(red frame)  
POINTER (red frame)  
Press POINT DOWN button to  
move POINTER.  
Select Menu to be adjusted  
Move POINTER (red frame) to MENU ICON that you want to  
select by pressing POINT RIGHT / LEFT buttons.  
2
ITEM  
Control or adjust item through ON-SCREEN MENU  
Press POINT DOWN button and move POINTER (red frame  
or red arrow) to ITEM that you want to adjust, and then press  
SELECT button to show ITEM DATA.  
3
SELECT  
BUTTON  
Adjust ITEM DATA by pressing POINT RIGHT / LEFT  
buttons.  
Refer to the following pages for details of respective  
adjustments.  
4
ITEM DATA  
Press POINT LEFT/RIGHT  
buttons to adjust value or  
set function.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
MENU BAR  
FOR PC SOURCE  
Press MENU BUTTON while connecting to PC input source.  
IMAGE SELECT MENU  
SCREEN MENU  
SETTING MENU  
Used to select  
Used to adjust size  
of image. [Normal  
/True/Wide  
/Digital zoom +/]  
(Refer to P30)  
Used to change  
settings of projector  
or reset Lamp  
Replace Counter.  
(Refer to P36, 37)  
GUIDE WINDOW  
PC SYSTEM MENU  
image level among  
Standard, Real  
and Image 1 ~ 4.  
(Refer to P28)  
Shows selected  
item of ON-  
SCREEN MENU.  
Used to select  
computer system.  
(Refer to P22, 23)  
INPUT MENU  
PC ADJUST MENU  
SOUND MENU  
IMAGE ADJUST MENU  
Used to adjust  
Used to select  
input source either  
Computer or  
Video.  
Used to adjust  
parameters to  
match with input  
signal format.  
Used to adjust  
volume or mute  
sound.  
computer image.  
[Contrast/Brightness  
/Color Temp.  
/White Balance (R/G/B)  
/Gamma]  
(Refer to P21)  
(Refer to P22)  
(Refer to P25-27)  
(Refer to P29)  
FOR VIDEO SOURCE  
Press MENU BUTTON while connecting to VIDEO input source.  
INPUT MENU  
Used to select  
input source  
either Video or  
Computer.  
IMAGE SELECT MENU  
SCREEN MENU  
Used to select image  
level among  
Standard, Cinema  
and Image 1 ~ 4.  
(Refer to P33)  
Used to set size of  
image to Normal  
or Wide.  
(Refer to P31)  
(Refer to P35)  
AV SYSTEM MENU  
IMAGE ADJUST MENU  
Same function as  
Menu for PC source.  
Same function as  
Menu for PC source.  
Used to select  
system of selected  
video source.  
Used to adjust picture image.  
[Contrast/Brightness/Color  
/Tint/Color Temp.  
(Refer to P32)  
/White balance (R/G/B)  
/Sharpness/Gamma  
/Noise Reduction/Progressive]  
(Refer to P34, 35)  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
TURNING ON / OFF PROJECTOR  
TURNING ON PROJECTOR  
Complete peripheral connections (with Computer, VCR, etc.)  
before turning on projector. (Refer to "CONNECTING  
PROJECTOR" on pages 11~13 for connecting the equipment.)  
Input position and  
Lamp mode status  
1
2
Computer 1  
Connect the projector's AC Power Cord into an AC outlet. LAMP  
Indicator lights RED, and READY Indicator lights GREEN.  
30  
NOTE : When On startfunction is ON, this projector is turned  
on automatically by connecting AC Power Cord to an  
AC outlet. (Refer to page 37.)  
Press POWER ON-OFF button on Top Control or on Remote  
Control Unit to ON. LAMP Indicator dims, and Cooling Fans  
start to operate. Preparation Display appears on a screen and  
count-down starts. The signal from PC or Video source appears  
after 30 seconds.  
3
Preparation Display disappears after 30 seconds.  
Current Input position and Lamp mode status are also displayed  
on screen for 5 seconds. (Refer to "LAMP MODE" on page 37.)  
TURNING OFF PROJECTOR  
Press POWER ON-OFF button on Top Control or on Remote  
Control Unit, and a message "Power off?" appears on a screen.  
1
2
Press POWER ON-OFF button again to turn off the projector.  
LAMP Indicator lights bright and READY Indicator turns off.  
After the projector is turned off, Cooling Fans operate (for 90  
seconds). During this "Cooling Down" period, this appliance can  
not be turned on.  
Power off?  
When projector has cooled down, READY Indicator lights  
GREEN again and you can turn the projector on. After cooling  
down completely, disconnect AC Power Cord.  
Message disappears after 4 seconds.  
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN  
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE  
TURNING IT OFF.  
When Power Managementfunction is ON, projector detects signal interruption and turns off Projection Lamp automatically.  
Refer to Power managementon pages 37.  
When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes, confirm READY  
indicator will light green and projector may be turned on by pressing POWER ON-OFF button.  
When both WARNING TEMP. and READY indicators to flash, a projector can not be turned on by pressing POWER ON-  
OFF button. In this case, follow procedures below:  
1. Disconnect AC Power Cord from an AC outlet.  
2. Turn a projector on again. (Refer to steps 2-3 of TURNING ON PROJECTOR on this page.)  
When WARNING TEMP. indicator continues to flash, follow procedures below:  
1. Disconnect AC Power Cord from an AC outlet.  
2. Check Air Filters for dust accumulation.  
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 41.)  
4. Turn a projector on again. (Refer to steps 2-3 of TURNING ON PROJECTOR on this page.)  
If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or  
service center.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
Press ZOOM button on Top Control or ZOOM L/M button on  
Remote Control Unit. The message Zoomis displayed.  
1
2
Press ZOOM L button or POINT UP button to make image  
larger, and press ZOOM M button or POINT DOWN button to  
make image smaller.  
Zoom  
Message disappears after 4 seconds.  
FOCUS ADJUSTMENT  
Press FOCUS button on Top Control or FOCUS L/M button on  
Remote Control Unit. The message Focusis displayed.  
1
2
Adjust focus of image by pressing FOCUS L/M button or  
POINT UP/DOWN button(s) .  
Focus  
NOTE;  
Focus adjustment may not function properly if the image is  
corrected by KEYSTONE adjustment.  
Message disappears after 4 seconds.  
LENS SHIFT ADJUSTMENT  
Press LENS SHIFT button on Top Control or LENS SHIFT L/M  
button on Remote Control Unit. Message Lens shiftis  
displayed.  
1
2
Lens shift  
Press POINT UP button or LENS SHIFT L button to move  
image up, press POINT DOWN or LENS SHIFT M button to  
move image down.  
KEYSTONE ADJUSTMENT  
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.  
Press KEYSTONE button on Top Control or Remote Control Unit  
or select Keystone on SETTING menu. (Refer to page 36.)  
Keystone dialog box appears.  
1
Correct keystone distortion by pressing POINT  
Arrows are white in no correction.  
2
UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to  
reduce the upper part of the image, and press POINT DOWN  
button to reduce the lower part. Press POINT LEFT button to  
reduce the left part, and press POINT RIGHT button to reduce  
the right part.  
Arrow(s) of direction being corrected turn(s) red.  
Arrow(s) disappear(s) at the maximum  
correction.  
If you press the KEYSTONE button on Top  
Control or on Remote Control Unit once more  
while the keystone dialog box is being  
displayed, the keystone adjustment will be  
canceled.  
Reduce the upper width  
with POINT UP button.  
Reduce the lower width  
with POINT DOWN button.  
Reduce the left part with  
POINT LEFT button.  
Reduce the right part with  
POINT RIGHT button.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
PICTURE FREEZE FUNCTION  
Press FREEZE button on Remote Control Unit to freeze the picture  
on-screen. To cancel FREEZE function, press FREEZE button again  
or press any other button.  
NO SHOW FUNCTION  
Press NO SHOW button on Remote Control Unit to black out the  
image. To restore to normal, press NO SHOW button again or press  
any other button.  
No show  
Message disappears after 4 seconds.  
P-TIMER FUNCTION  
Press P-TIMER button on Remote Control Unit. The timer display 00  
: 00appears on the screen and the timer starts to count time (00 : 00  
~ 59 : 59).  
To stop P-TIMER display, press P-TIMER button. And then, press P-  
TIMER button again to cancel P-TIMER function.  
SOUND ADJUSTMENT  
Indicates approximate  
level of volume.  
DIRECT OPERATION  
Volume  
Press VOLUME (+/) button(s) on Top Control or on Remote Control  
Unit to adjust volume. Volume dialog box appears on the screen for a  
few seconds.  
(+) button to increase volume, and () button for decreasing.  
Mute  
Press MUTE button to set  
Mute function On or Off.  
Press MUTE button on Remote Control Unit to cut off sound. To  
restore sound to its previous level, press MUTE button again or press  
Volume (+/) button(s).  
The display disappears after 4 seconds.  
MENU OPERATION  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to  
SOUND Menu icon.  
SOUND MENU  
1
Press POINT DOWN button to move a red frame pointer to the  
item that you want to select, and then press SELECT button.  
SOUND Menu icon  
2
Indicates approximate  
level of volume.  
Volume  
To increase volume, press POINT RIGHT button, and press POINT  
LEFT button to decrease volume.  
Close SOUND Menu.  
Mute  
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box  
display is changed to Onand sound is cut off. To restore sound to  
its previous level, press POINT LEFT/RIGHT button(s) again.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
SELECTING INPUT SOURCE  
DIRECT OPERATION  
Select INPUT source by pressing INPUT button on Top Control.  
Select INPUT source by pressing COMPUTER 1 or COMPUTER 2  
button on Remote Control Unit.  
If projector can not reproduce proper image, select correct input  
source through MENU OPERATION (see below).  
INPUT button  
Computer 1  
Computer 2  
Video  
MENU OPERATION  
INPUT MENU  
When connect the output (Analog) from computer to  
Computer 1 (HDB 15-pin) terminal on the projector.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
1
INPUT Menu icon  
Move a pointer (red arrow)  
to Computer 1 and press  
SELECT button.  
Press POINT DOWN button to move a red arrow pointer to  
Computer 1 and then press SELECT button. Source Select  
Menu will appear.  
2
Computer 1  
INPUT MENU  
Computer 2  
Press POINT DOWN button and a red-arrow icon will appear.  
Move arrow to "RGB" and press SELECT button.  
3
When computer is connected to Computer 1, select  
RGB.  
Source Select Menu  
RGB  
Move a pointer to RGB  
and press SELECT button.  
When video equipment is connected to Computer 1  
terminal, select RGB (Scart). Refer to P31.  
RGB (Scart)  
When connect the output (Digital/Analog) from computer  
to Computer 2 (DVI-I) terminal on the projector.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
INPUT Menu icon  
1
Move a pointer (red arrow)  
to Computer 2 and press  
SELECT button.  
Press POINT DOWN button to move a red arrow pointer to  
Computer 2 and then press SELECT button. Source Select  
Menu will appear.  
2
Move a pointer to either RGB (Digital) or RGB (Analog) and then  
press SELECT button.  
3
Source Select Menu  
When digital signal is connected to DVI terminal,  
select Digital.  
RGB (Digital)  
Move a pointer to RGB  
(Digital) or RGB (Analog)  
and press SELECT button.  
When analog signal is connected to DVI terminal,  
select Analog.  
RGB (Analog)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
SELECTING COMPUTER SYSTEM  
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to  
COMPATIBLE COMPUTER SPECIFICATIONSon page 24). When selecting Computer, this projector automatically tunes  
to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)  
Note : Projector may display one of the following messages.  
When projector can not recognize connected signal as  
PC system provided in this projector, Auto PC Adjustment  
function operates to adjust projector and the message  
Autois displayed on SYSTEM Menu icon. (Refer to  
P25.) When image is not provided properly, manual  
adjustment is required. (Refer to P26 and 27.)  
PC SYSTEM MENU  
Auto  
SYSTEM Menu icon  
Displays system being  
selected.  
There is no signal input from computer. Make sure the  
connection of computer and a projector is set correctly.  
(Refer to TROUBLESHOOTING on page 42.)  
––––  
D-VGA, D-SVGA or D-XGA  
When digital computer signal is received on DVI terminal,  
above message is displayed on PC SYSTEM Menu icon.  
SELECT COMPUTER SYSTEM MANUALLY  
This projector automatically selects PC system among those provided  
in this projector and PC system can be also selected manually.  
PC SYSTEM MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to PC  
SYSTEM Menu icon.  
1
SYSTEM Menu icon  
Displays system being selected.  
Press POINT DOWN button to move a red arrow pointer to the  
The systems on this dialog box  
can be selected.  
2
system that you want to set, and then press  
SELECT button.  
Custom Mode (1~5) set in PC  
ADJUST Menu. (P26, 27)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
COMPATIBLE COMPUTER SPECIFICATIONS  
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140  
MHz of Dot Clock.  
ON-SCREEN  
DISPLAY  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
VGA 1  
VGA 2  
640 x 480  
720 x 400  
640 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
31.47  
31.47  
31.47  
37.86  
37.86  
37.50  
43.269  
34.97  
35.00  
15.625  
15.734  
35.156  
37.88  
46.875  
53.674  
48.08  
37.90  
34.50  
38.00  
38.60  
32.70  
38.00  
49.72  
48.36  
68.677  
60.023  
56.476  
60.31  
48.50  
44.00  
63.48  
36.00  
62.04  
59.88  
70.09  
70.09  
74.38  
72.81  
75.00  
85.00  
66.60  
66.67  
XGA 11  
XGA 12  
XGA 13  
XGA 14  
XGA 15  
MAC 19  
MAC 21  
SXGA 1  
SXGA 2  
SXGA 3  
SXGA 4  
SXGA 5  
SXGA 6  
SXGA 7  
SXGA 8  
SXGA 9  
SXGA 10  
SXGA 11  
SXGA 12  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 864  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 960  
1152 x 900  
1152 x 900  
61.00  
35.522  
46.90  
47.00  
58.03  
60.24  
68.68  
64.20  
62.50  
63.90  
63.34  
63.74  
71.69  
81.13  
63.98  
79.976  
60.00  
61.20  
71.40  
50.00  
50.00  
63.37  
76.97  
61.85  
46.43  
63.79  
63.93  
75.00  
80.00  
45.00  
33.75  
33.75  
28.125  
75.70  
86.96  
(Interlace)  
VGA 3  
58.20  
58.30  
72.00  
75.08  
75.06  
70.40  
58.60  
60.00  
59.98  
60.01  
67.19  
76.107  
60.02  
75.025  
60.00  
65.20  
75.60  
VGA 4  
VGA 5  
VGA 6  
VGA 7  
MAC LC13  
MAC 13  
RGB  
640 x 480  
––––––––  
50  
(Interlace)  
60  
––––––––  
RGB  
(Interlace)  
SVGA 1  
SVGA 2  
SVGA 3  
SVGA 4  
SVGA 5  
SVGA 6  
SVGA 7  
SVGA 8  
SVGA 9  
SVGA 10  
SVGA 11  
MAC 16  
XGA 1  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
56.25  
60.32  
75.00  
85.06  
72.19  
61.03  
55.38  
60.51  
60.31  
51.09  
60.51  
74.55  
60.00  
84.997  
75.03  
70.07  
74.92  
60.02  
54.58  
79.35  
86.00  
(Interlace)  
94.00  
(Interlace)  
SXGA 13 1280 x 1024  
SXGA 14 1280 x 1024  
SXGA 15 1280 x 1024  
SXGA 16 1280 x 1024  
60.01  
72.00  
66.00  
SXGA 17  
1152 x 900  
86.70  
XGA 2  
SXGA 18 1280 x 1024  
SXGA 19 1280 x 1024  
SXGA 21 1400 x 1050  
(Interlace)  
XGA 3  
60.18  
60.00  
75.08  
75.08  
60.00  
XGA 4  
XGA 5  
MAC  
1280 x 960  
XGA 6  
MAC  
1280 x 1024  
––––––––  
XGA 7  
720p (HDTV)  
1035i (HDTV)  
1080i 60(HDTV)  
1080i 50(HDTV)  
60.00  
(Interlace)  
60.00  
(Interlace)  
50.00  
(Interlace)  
––––––––  
––––––––  
––––––––  
XGA 8  
87.17  
(Interlace)  
XGA 9  
XGA 10  
77.07  
When a input signal is digital from DVI terminal, refer to the chart below.  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
D-VGA  
640 x 480  
800 x 600  
31.469  
37.879  
59.940  
60.317  
D-XGA  
1024 x 768  
48.363  
60.004  
D-SVGA  
NOTE : Specifications are subject to change without notice.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PC ADJUSTMENT  
AUTO PC ADJUSTMENT  
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your  
computer. Auto PC Adjustment function can be operated as follows.  
Auto PC Adj.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to PC  
ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to  
AUTO PC Adj. icon and then press SELECT button twice.  
This Auto PC Adjustment can be also executed by pressing  
AUTO PC ADJ. button on Top Control or on Remote Control  
Unit.  
PC ADJUST Menu icon  
Move a red frame pointer to AUTO PC  
Adj. icon and press SELECT button.  
Store adjustment parameters.  
Adjustment parameters from Auto PC Adjustment can be memorized  
in this projector. Once parameters are memorized, the setting can be  
done just by selecting Mode in PC SYSTEM Menu (P23). Refer to  
step 3 of MANUAL PC ADJUSTMENT section (P27).  
NOTE  
G Fine sync, Total dots and Picture Position of some computers can  
not be fully adjusted with this Auto PC Adjustment function. When  
the image is not provided properly through this function, manual  
adjustments are required. (Refer to page 26, 27.)  
G Auto PC Adjustment function can not be operated in Digital Signal  
input on DVI terminal and RGB, 1035i (HDTV), 1080i50 (HDTV)”  
or 1080i60 (HDTV)is selected on PC SYSTEM Menu (P23).  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
MANUAL PC ADJUSTMENT  
This projector can automatically tune to the display signals from most personal computers currently distributed. However,  
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-  
Scan system of this projector. If this happens, projector can not reproduce a proper image and the image may be  
recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.  
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special  
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This  
enables you to recall the setting for a specific computer whenever you use it.  
Note : This PC ADJUST Menu can not be operated in Digital Signal input on DVI terminal is selected on PC SYSTEM  
MENU (P23).  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to PC  
ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust and then press SELECT button.  
Adjustment dialog box will appear. Press POINT LEFT/RIGHT  
button to adjust value.  
PC ADJUST Menu icon  
Move a red frame icon to the item and  
press SELECT button.  
Fine sync  
Adjusts an image as necessary to eliminate flicker from the display.  
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)  
Shows status  
(Stored / Free) of the  
selected Mode.  
Total dots  
Selected Mode  
The number of total dots in one horizontal period. Press POINT  
LEFT/RIGHT button(s) and adjust number to match your PC image.  
Horizontal  
Adjusts horizontal picture position. Press POINT LEFT/RIGHT  
button(s) to adjust the position.  
Press POINT LEFT/RIGHT  
button to adjust the value.  
Vertical  
Adjusts vertical picture position. Press POINT LEFT/RIGHT  
button(s) to adjust the position.  
Press SELECT button at this icon to  
adjust Clamp,” “Display area (H/V)or  
set Full screen.”  
Current mode  
Press SELECT button to show the information of computer selected.  
Clamp  
Current mode  
Adjusts clamp level. When the image has a dark bar(s), try this  
adjustment.  
Press SELECT button at  
Current mode icon to show  
the information of computer  
connected.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
Display area  
Selects area displayed with this projector. Select the resolution at  
Display area dialog box.  
Press SELECT button at Display  
area icon and Display area dialog  
box appears.  
Display area H  
Adjustment of horizontal area displayed with this projector. Press  
POINT LEFT/RIGHT button(s) to decrease/increase value and then  
press SELECT button.  
Display area  
Display area V  
Adjustment of vertical area displayed with this projector. Press  
POINT LEFT/RIGHT button(s) to decrease/increase value and then  
press SELECT button.  
Press POINT LEFT  
/RIGHT button(s) to adjust  
value and then press  
SELECT button.  
Full screen  
Press POINT LEFT/RIGHT button(s) to switch Full screen function to  
Onor Off.Set Onto resize the image with 4 x 3 aspect ratio to  
fit the screen.  
NOTE : Fine sync, Display area, Display area H, Display area V and  
Full screen can not be adjusted when RGB, 1035i  
(HDTV), 1080i50(HDTV)or 1080i60 (HDTV)is selected  
on PC SYSTEM Menu (P23).  
To store adjustment data.  
This Mode has parameters being stored.  
Store  
3
To store adjustment parameters, move a red frame pointer to  
Store icon and then press SELECT button. Move a red arrow  
pointer to any of Mode 1 to 5 that you want to store to and then  
press SELECT button.  
Mode free  
To clear adjustment parameters previously set, move a red  
frame pointer to Mode free icon and then SELECT button. Move  
a red arrow pointer to the Mode that you want to clear and then  
press SELECT button.  
Vacant Mode  
Store icon  
Shows values of Total dots,”  
Horizontal,” “Vertical,” “Display  
area H,and Display area V.”  
Other icons operate as follows.  
Reset  
To clear adjustment data.  
Reset all adjust parameters on adjustment dialog box to previous  
figure.  
Quit  
Closes PC ADJUST MENU.  
Close this dialog box.  
Mode free icon  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE IMAGE ADJUSTMENTS  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Real, Image 1, Image 2, Image 3  
and Image 4 by pressing IMAGE button on Top Control or on Remote  
Control Unit.  
IMAGE button  
Standard  
Real  
Standard  
Normal picture level preset on this projector.  
Image 1  
Image 2  
Image 3  
Image 4  
Real  
Picture level with improved halftone for graphics.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P29).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture level preset on this projector.  
Move a red frame pointer to the level  
and press SELECT button.  
Real  
Picture level with improved halftone for graphics.  
IMAGE 1~4  
The level being selected.  
User preset picture adjustment in IMAGE ADJUST Menu (P29).  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to  
IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust. and then press SELECT button.  
The level of each item is displayed. Adjust each level by  
pressing POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move a red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press POINT LEFT button to decrease contrast, and POINT RIGHT  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to adjust image darker, and POINT  
RIGHT button to adjust brighter. (From 0 to 63.)  
Selected Image level  
Color temp.  
Press either POINT LEFT button or POINT RIGHT button to Color  
temp. level that you want to select. (XLow, Low, Mid or High)  
White balance (Red)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Press POINT LEFT button to lighten red tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
White balance (Green)  
Press POINT LEFT button to lighten green tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Store icon  
Press SELECT button at this icon to  
store the adjustment.  
White balance (Blue)  
Press POINT LEFT button to lighten blue tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Gamma  
Press either POINT LEFT button or POINT RIGHT button to obtain  
better balance of contrast. (From 0 to 15.)  
Store  
3
To store manually preset image, move a red frame pointer to  
Store icon and press SELECT button. Image Level Menu will  
appear. Move a red frame pointer to the Image 1 to 4 where you  
want to set and then press SELECT button.  
Other icons operates as follows.  
Image Level Menu  
Reset  
Move a red frame pointer to any  
of Image 1 to 4 where you want  
to set and then press SELECT  
button.  
Reset all adjustment to previous figure.  
Quit  
Closes IMAGE MENU.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
SCREEN Menu icon.  
SCREEN MENU  
1
2
Press POINT DOWN button and move a red frame pointer to the  
function that you want to select and then press SELECT button.  
SCREEN Menu icon  
Move the red frame to the function and  
press SELECT button.  
Normal  
Provides image to fit screen size.  
True  
Provides image in its original size. When the original image size is  
larger than screen size (1024 x 768), this projector enters Digital  
zoom +mode automatically.  
NOTE  
G Picture screen adjustment can not be operated  
when 1035i (HDTV), 1080i50 (HDTV)or  
1080i60 (HDTV)is selected on PC SYSTEM  
Menu (P23).  
Wide  
Provides image to fit wide video aspect ratio (16 : 9) by expanding  
image width uniformly. This function can be used for providing a  
squeezed video signal at 16 : 9.  
G Wide can not be selected when 720p (HDTV)is  
selected on PC SYSTEM Menu (P23).  
G True and Digital zoom +/can not be operated  
when RGBis selected on PC SYSTEM Menu  
(P23).  
Digital zoom +  
When Digital zoom + is selected, ON-SCREEN MENU disappears  
and the message D. Zoom +is displayed. Press SELECT button to  
expand image size. And press POINT UP/DOWN/LEFT/RIGHT  
button(s) to pan the image. Panning function can work only when  
the image is larger than screen size.  
A projected image can be also expanded by pressing D.ZOOM L  
button on Remote Control Unit.  
G This projector can not display any resolution higher  
than 1280 X 1024. If your computers screen  
resolution is higher than 1280 X 1024, reset the  
resolution to the lower before connecting projector.  
G The image data in other than XGA (1024 x 768) is  
modified to fit the screen size in initial mode.  
G Panning function may not operate properly if the  
computer system prepared on PC ADJUST Menu  
is used.  
Digital Zoom –  
When Digital zoom is selected, ON-SCREEN MENU disappears  
and the message D. Zoom –” is displayed. Press SELECT button to  
compress image size.  
A projected image can be also compressed by pressing D.ZOOM M  
button on Remote Control Unit.  
To cancel Digital Zoom +/mode, press any button except D.ZOOM  
L/M, SELECT, POINT and LASER buttons.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING INPUT SOURCE  
DIRECT OPERATION  
INPUT button  
Computer 1  
Select INPUT source by pressing INPUT button on Top Control.  
Select INPUT source by pressing COMPUTER 1 or VIDEO button on  
Remote Control Unit.  
If projector can not reproduce proper image, select correct input  
source through MENU OPERATION (see below).  
Computer 2  
Video  
INPUT MENU  
MENU OPERATION  
When connecting to those equipment, select a type of  
Video source in SOURCE SELECT MENU.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
Move a pointer to Video and  
press SELECT button.  
1
Press POINT DOWN button to move a red arrow pointer to  
Video and then press SELECT button. Source Select Menu will  
appear.  
2
VIDEO  
Move a pointer to the source that you want to select and then  
press SELECT button.  
3
Projector automatically detects incoming Video signal,  
and adjusts itself to optimize its performance.  
Auto  
When both VIDEO jack and S-VIDEO jack are  
connected, S-VIDEO jack has priority over VIDEO jack.  
Source Select Menu (VIDEO)  
Move a pointer to the source  
and press SELECT button.  
When both Y-Pb/Cb-Pr/Cr jacks and S-VIDEO jack are  
connected, Y-Pb/Cb-Pr/Cr jacks have priority over S-  
VIDEO jack.  
When video input signal is connected to VIDEO jack,  
select Video.  
Video  
When video input signal is connected to S-VIDEO jack,  
select S-Video.  
S-Video  
When video input signal is connected to Y-Pb/Cb-  
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.  
Y,Pb/Cb,Pr/Cr  
INPUT MENU  
When connect the 21-pin Scart (RGB) output from video  
equipment to computer 1 (HDB 15-pin) terminal on the  
projector.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
INPUT Menu icon.  
INPUT Menu icon  
1
Move a pointer (red arrow)  
to Computer and press  
SELECT button.  
Press POINT DOWN button to move a red arrow pointer to  
Computer 1 and then press SELECT button. Source Select  
Menu will appear.  
2
Computer 1  
Press POINT DOWN button and a red-arrow icon will appear.  
Move arrow to "RGB (Scart)" and press SELECT button.  
3
Source Select Menu  
Move a pointer to  
RGB (Scart) and press  
SELECT button.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING VIDEO SYSTEM  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT buttons to move a red frame pointer to AV  
SYSTEM Menu icon.  
1
2
Press POINT DOWN button to move a red arrow pointer to the  
system that you want to select and then press SELECT button.  
VIDEO JACK OR S-VIDEO JACK  
AV SYSTEM MENU (VIDEO OR S-VIDEO)  
Auto  
Projector automatically detects incoming Video system, and adjusts  
itself to optimize its performance.  
When Video System is PAL-M or PAL-N, select system manually.  
AV SYSTEM Menu icon  
This box indicates the system  
being selected.  
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N  
If projector can not reproduce proper video image, it is necessary to  
select a specific broadcast signal format among PAL, SECAM, NTSC,  
NTSC 4.43, PAL-M, and PAL-N.  
Move the pointer to the  
system and press  
SELECT button.  
Y, Pb/Cb, Pr/Cr JACKS  
AV SYSTEM MENU (COMPONENT VIDEO)  
Auto  
Projector automatically detects incoming Video signal, and adjusts  
itself to optimize its performance.  
COMPONENT VIDEO SIGNAL FORMAT  
AV SYSTEM Menu icon  
This box indicates the system  
being selected.  
If projector can not reproduce proper video image, it is necessary to  
select a specific component video signal format among 480i, 575i,  
480p, 575p, 720p, 1035i and 1080i.  
Move the pointer to the  
system and press  
SELECT button.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
PICTURE IMAGE ADJUSTMENTS  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Cinema, Image 1, Image 2,  
Image 3 and Image 4 by pressing IMAGE button on Top Control or on  
Remote Control Unit.  
IMAGE button  
Standard  
Cinema  
Image 1  
Image 2  
Image 3  
Image 4  
Standard  
Normal picture level preset on this projector.  
Cinema  
Picture level adjusted for the picture with fine tone.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P34, 35).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button to move a red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture level preset on this projector.  
Cinema  
Move the red frame pointer to the  
level and press SELECT button.  
Picture level adjusted for the picture with fine tone.  
IMAGE 1~4  
The level being selected.  
User preset picture adjustment in IMAGE ADJUST Menu (P34, 35).  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press POINT DOWN button to move a red frame pointer to the  
item that you want to adjust and then press SELECT button.  
The level of each item is displayed. Adjust each level by  
pressing POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move a red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press POINT LEFT button to decrease contrast, and POINT RIGHT  
button to increase contrast. (From 0 to 63.)  
Brightness  
Press POINT LEFT button to adjust image darker, and POINT  
RIGHT button to adjust brighter. (From 0 to 63.)  
Color  
Press POINT LEFT button to lighten color, and POINT RIGHT button  
to deeper color. (From 0 to 63.)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Tint  
Press POINT LEFT button or POINT RIGHT button to obtain proper  
color. (From 0 to 63.)  
Press SELECT button at this icon to  
display other items.  
Color temp.  
Press either POINT LEFT button or POINT RIGHT button to Color  
temp. level that you want to select. (XLow, Low, Mid or High)  
White balance (Red)  
Press POINT LEFT button to lighten red tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
Press SELECT button at this icon to  
display previous items.  
White balance (Green)  
Press POINT LEFT button to lighten green tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
White balance (Blue)  
Press POINT LEFT/RIGHT buttons  
to adjust value.  
Press POINT LEFT button to lighten blue tone and POINT RIGHT  
button to deeper tone. (From 0 to 63.)  
15  
Sharpness  
Press POINT LEFT button to soften the image, and POINT RIGHT  
button to sharpen the image. (From 0 to 31.)  
L1  
Gamma  
Store icon  
Press either POINT LEFT button or POINT RIGHT button to obtain  
better balance of contrast. (From 0 to 15.)  
Press SELECT button at this icon to  
store the value.  
Noise reduction  
NOTE :  
Press POINT LEFT/RIGHT button(s) to change noise reduction  
mode. Dialog box display is changed to Onto reduce noise (rough  
parts) of image. Press POINT LEFT/RIGHT button(s) again, to  
change noise reduction mode to off.  
Tint can not be adjusted when the video system is  
PAL, SECAM, PAL-M or PAL-N.  
Progressive can not be operated when 480p,  
575p, 720p, 1035ior 1080iis selected on AV  
SYSTEM MENU (P32).  
Progressive scan  
Press POINT LEFT/RIGHT button(s) to change progressive scan  
mode. Dialog box display is changed to Off, L1, L2.  
Off ··· Progressive scan mode to OFF.  
L1 ···· Progressive scan mode to ON (for active picture).  
L2 ···· Progressive scan mode to ON (for still picture).  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
Store  
3
To store the adjustment data, move a red frame pointer to Store  
icon and press SELECT button. Image Level Menu will appear.  
Move a red frame pointer to the Image Level 1 to 4 and then  
press SELECT button.  
Image Level Menu  
Other icons operates as follows.  
Move a red frame pointer to  
the image icon to be set  
and then press SELECT  
button.  
Reset  
Reset all adjustment to previous figure.  
Quit  
Closes IMAGE MENU.  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red frame pointer to  
SCREEN Menu icon.  
SCREEN MENU  
1
2
Press POINT DOWN button and move a red frame pointer to the  
function that you want to select and then press SELECT button.  
SCREEN Menu icon  
Move the red frame to the function and  
Normal  
press SELECT button.  
Provides image at a normal video aspect ratio of 4 : 3.  
NOTE : SCREEN Menu can not be operated when  
720p,” “1035i,or 1080iis selected on AV  
SYSTEM Menu (P32).  
Wide  
Provides image at a wide screen ratio of 16 : 9.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
SETTING MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
POINT LEFT/RIGHT button(s) to move a red-frame pointer to  
SETTING icon.  
SETTING MENU  
1
2
Press POINT DOWN button to move a red-frame pointer to the  
Set a red frame  
SETTING Menu icon  
item that you want to set and then press  
SELECT button.  
pointer to the item  
and press SELECT  
button.  
Setting dialog box appears.  
Language  
Language used in ON-SCREEN MENU is selectable from among  
English, German, French, Italian, Spanish, Portuguese, Dutch,  
Swedish, Russian, Chinese, Korean and Japanese.  
Keystone  
When the image is distorted, select Keystone. ON-SCREEN MENU  
disappears and Keystone dialog box is displayed.  
Store ··· Store the keystone adjustment data when disconnect AC  
Power Cord from an AC outlet.  
When pressing SELECT  
button at Language,  
Language Menu appears.  
Reset ··· Reset the keystone adjustment data when disconnect AC  
Power Cord from an AC outlet.  
Correct  
keystone  
distortion  
by  
pressing  
POINT  
UP/DOWN/LEFT/RIGHT button(s).  
ADJUSTMENT on page 20.  
Refer to KEYSTONE  
Blue back  
When this function is On,this projector will produce a blue image  
instead of the video noise on the screen when any input source is  
unplugged or turned off.  
Display  
This function decides whether to display On-Screen Displays.  
On ··· shows all the On-Screen Displays.  
Off ···· sets On-Screen Displays disappeared except;  
G ON-SCREEN MENU  
Move a pointer to the item  
and then press POINT  
LEFT/RIGHT button(s).  
G Power off?message  
Ceiling function  
Logo  
When this function is On,projector displays our logo when starting  
up.  
Ceiling  
When this function is On,picture is top / bottom and left / right  
reversed. This function is used to project the image from a ceiling  
mounting the projector.  
Rear function  
Rear  
When this function is On,picture is left / right reversed. This  
function is used to project the image to a rear projection screen.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
Power management  
This function turns Projection Lamp off when this projector detects  
signal interruption and is not used for a certain period in order to  
reduce power consumption and maintain the Lamp-life. (This  
projector is shipped with this function ON.)  
Time left until Lamp off.  
Power Management function operates to turn Projection Lamp off  
when the input signal is interrupted and any button is not pressed  
over 5 minutes. This function operates as follows;  
1. When any input signal is interrupted, No signaland the  
counting down display appears (for 5 minutes).  
2. After counting down for 5 minutes, Projection Lamp and  
READY Indicator are turned off. (Cooling Fans keep running.)  
3. READY Indicator starts to flash after cooling down Projection  
Lamp about for 90 seconds (Power Management mode).  
In this Power Management mode, Projection Lamp is  
automatically turned on when the input signal is connected or  
projector is operated with any button on Top Control or on  
Remote Control Unit again.  
Press SELECT button at this icon to  
display other items.  
On start  
When this function is On,projector is automatically turned on just  
by connecting AC Power cord to a wall outlet.  
Note ; Be sure to turn projector off properly (refer to the section  
TURNING OFF PROJECTORon P19). If projector is turned  
off in the wrong steps, On Start function does not operate  
properly.  
Press SELECT button at this icon to  
display previous items.  
Lamp mode  
On  
On  
When selecting the  
and set into the low power consumption mode.  
(Eco), the projector reduce the brightness  
"
"
Move the pointer to the item and  
then press POINT LEFT/RIGHT  
button(s).  
Code 1  
Remote control  
This projector has eight different remote control codes; the factory-  
set normal code (Code 1) and the other seven codes (Code 2 to  
Code 8). This switching function prevents remote control operation  
mixture (jam) when operating several projectors or video equipment  
together.  
Remote control  
When pressing SELECT button at  
Remote control, Remote control  
code Menu appears.  
On  
On  
For example operating projector in Code 7,both projector and  
Remote Control Unit must be switched to Code 7.”  
To change the code of Projector;  
To change the Remote control code of the projector used in ON-  
SCREEN MENU is selectable from Code 1 to Code 8.  
Code 1  
To change the code of the Remote Control Unit;  
To change the remote control code of the Remote Control Unit, set  
the DIP switches 1-3 inside the battery compartment box of the  
Remote Control Unit. (Refer to P14.)  
Lamp counter reset  
This function is used to reset Lamp Replace Counter. When  
replacing Projection Lamp, reset Lamp Replace Counter by using  
this function. Refer to page 38 for operation.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
LAMP REPLACEMENT  
LAMP REPLACE  
When the life of the Projection Lamp of this projector draws to an end,  
the LAMP REPLACE indicator lights yellow. If this indicator lights  
yellow, replace the projection lamp with a new one promptly.  
TOP CONTROL  
This indicator lights yellow  
ON-OFF  
SELECT  
when the life of the projection  
lamp draws to an end.  
Replace the Projection Lamp  
with a new one promptly.  
CAUTION  
Allow a projector to cool, for at least 45 minutes before  
you open Lamp Cover. The inside of a projector can  
become very hot.  
For continued safety, replace with a lamp assembly of  
the same type.  
Do not drop a lamp assembly or touch a glass bulb! The  
glass can shatter and may cause injury.  
LAMP COVER  
SCREW  
Follow these steps to replace the lamp assembly.  
Turn off the projector and disconnect the AC plug. Allow the  
projector to cool for at least 45 minutes.  
1
To remove Lamp Cover, remove the screw with a screwdriver.  
2
Loosen 2 screws with a screwdriver and pull out Lamp Assembly  
by grasping Handle.  
3
Replace Lamp Assembly with a new one and tighten 2 screws  
back into position. Make sure that Lamp Assembly is set  
properly. Replace Lamp Cover and tighten the screw.  
HANDLE  
4
SCREWS  
Connect AC Power Cord to the projector and turn on the  
projector.  
5
Reset the Lamp Replace Counter.  
Refer to LAMP REPLACE COUNTERon the next page .  
6
LAMP  
ASSEMBLY  
ORDER REPLACEMENT LAMP  
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the  
following information to the dealer.  
G Model No. of your projector  
G Replacement Lamp Type No.  
:
:
103-002001  
03-000712-01P  
(Service Parts No. 610 305 5602)  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
LAMP REPLACE COUNTER  
Be sure to reset the Lamp Replace Counter after the Lamp Assembly is replaced. When the Lamp Replace Counter is reset,  
the LAMP REPLACE Indicator stops lighting.  
Turn projector on, press MENU button and ON-SCREEN  
MENU will appear. Press POINT LEFT/RIGHT button(s) to  
move a red frame pointer to SETTING Menu icon (refer to  
1
page 36, 37).  
On  
Press POINT DOWN button to move a red frame pointer to  
2
On  
Lamp counter resetand then press  
SELECT button. The  
message "Lamp replace counter reset?" is displayed. Move  
the pointer to [Yes] and then press SELECT button.  
Code 1  
Another confirmation dialog box appears and select [Yes] to  
reset Lamp Replace Counter.  
3
Move the pointer to Lamp counter reset and then press  
SELECT button. The message Lamp replace counter  
reset?is displayed.  
NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.  
LAMP HANDLING PRECAUTIONS  
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper  
handling may result in accidents, injury, or create a fire hazard.  
G Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no  
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a  
shorter period of time than other similar lamps.  
G If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR  
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.  
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous  
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.  
G A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its  
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in  
which the projector and lamp are being used.  
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.  
If a lamp explodes, disconnect the projectors AC plug from the AC outlet immediately. Contact an  
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check  
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out  
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one  
should check the inside of the projector except those who are authorized trained technicians and who are  
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who  
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken  
glass.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
OPERATING WIRELESS MOUSE  
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most  
Personal Computers. POINT button, drag ON/OFF button and two CLICK buttons are used for wireless mouse operation.  
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON-  
SCREEN MENU or any message / dialog box is displayed on the screen instead of PC mouse pointer, this Wireless Mouse  
function can not be used.  
INSTALLATION  
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of the mouse driver (not  
supplied) is required. Make sure that the mouse driver is properly installed in your computer. And make sure that the mouse  
port (or USB port) of a Personal Computer is activated.  
Connect the mouse port (or USB port) of your computer to  
Control Port (or USB connector) of this projector with Control  
Cable (or USB cable). (Refer to page 11, 12 for connection.)  
Note : When your computer has no mouse  
1
port, connect Serial Port of your  
computer to Control Port of the  
projector with Control Cable for Serial  
Port (supplied).  
Turn the projector on first, and then turn on your computer.  
When the computer is switched on first, Wireless Mouse may not  
work properly.  
2
OPERATING WIRELESS MOUSE  
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, Drag ON/OFF button, LEFT CLICK  
button and RIGHT CLICK button on Wireless Remote Control Unit.  
POINT button  
Used to move PC mouse pointer. The pointer is moved  
DRAG ON  
corresponding with the direction you are pressing.  
INDICATOR  
LEFT CLICK button  
This button has the same function as the left button in a PC mouse.  
Press this button and the POINT button to drag a selected screen  
object.  
RIGHT CLICK button  
This button has the same function as the right button in a PC mouse.  
DRAG ON/OFF button  
DRAG ON/OFF  
button  
Use this button and the POINT button to drag a selected screen  
object. Press and release the Drag ON/OFF button, DRAG ON  
INDICATOR lights green and the remote control is in Drag mode.  
Use the POINT button in the direction that you want to drag the  
screen object. Press and release the Drag ON/OFF button again or  
press any other button, to drop the object at the new screen location.  
POINT button  
(Move the pointer)  
LEFT CLICK button  
RIGHT CLICK button  
(left button of the mouse)  
(right button of the mouse)  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
MAINTENANCE  
WARNING TEMP. INDICATOR  
WARNING TEMP. Indicator flashes red and projector is automatically turned off when an internal temperature of the  
projector exceeds normal temperature. Wait at least 5 minutes before turning on projector again.  
When WARNING TEMP. Indicator continues to flash, check the items listed below.  
Ventilation Slots of the projector may be blocked. In such an event, reposition the projector so that Ventilation Slots  
are not obstructed.  
1
Air Filter may be clogged with dust particles. Clean Air Filter by following the section AIR FILTER CARE AND  
CLEANING below.  
2
If WARNING TEMP. Indicator remains on after performing the above checks, Cooling Fans or the Internal Circuits may  
be malfunctioning. Contact service personnel from an authorized dealer or a service station.  
3
AIR FILTER CARE AND CLEANING  
Removable Air Filters prevents dust from accumulating on the surface of Projection Lens and Projection Mirror. Should Air  
Filters become clogged with dust particles, it will reduce Cooling Fanseffectiveness and may result in internal heat build up  
and adversely affect the life of the projector. Clean Air Filters following the steps below:  
AIR INTAKE  
VENT  
AIR FILTER  
Pull up and remove.  
Turn off the projector, and disconnect AC power cord from the  
AC outlet.  
1
2
Turn the projector upside down and remove four Air Filters by  
pulling the latches upward.  
Clean Air Filters with a brush or wash out dust and particles.  
3
4
Replace four Air Filters properly. Make sure that Air Filters are  
fully inserted.  
Clean Air Intake Vent with a brush or wash out dust and  
particles.  
5
CAUTION  
Do not operate the projector with Air Filter removed. Dust  
may accumulate on LCD Panel and Projection Mirror  
degrading picture quality.  
Do not put small parts into Air Intake Vents. It may result in  
malfunction of the projector.  
RECOMMENDATION  
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments  
may cause poor image quality.  
When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements  
inside the projector. This condition may degrade the quality of a projected image.  
When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.  
CLEANING PROJECTION LENS  
Follow these steps to clean Projection Lens:  
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.  
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.  
1
Lightly wipe a cleaning cloth over Projection Lens.  
2
3
When the projector is not in use, replace Lens Cover.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TROUBLESHOOTING  
Before calling your dealer or service center for assistance, check the matters below once again.  
1. Make sure you have connected a projector to your computer or video equipment as described in the section  
"CONNECTING PROJECTOR" on pages 11 ~ 13.  
2. Check cable connection. Verify that all computer, video and power cord are properly connected.  
3. Verify that all power is switched on.  
4. If a projector still does not produce an image, re-start your computer.  
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. The  
problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to  
turn the computer and monitor off before you power up the projector. Power the equipment back on in order of : Projector  
and computer.)  
6. If the problem still exists, check the following chart.  
Problem:  
No power.  
Try these Solutions  
G Plug a projector into your AC outlet.  
G Make sure READY Indicator lights.  
G Wait 90 seconds after a projector is turned OFF when turning the projector back on.  
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as  
follows:  
1. LAMP indicator lights bright and READY indicator turns off.  
2. After 90 seconds, READY indicator lights green again and a projector may be  
turned on by pressing Power ON-OFF button.  
G Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY  
indicator flashes, the projector can not be turned on.  
(See "TURNING ON/OFF PROJECTOR" section on page 19.)  
G Check Projection Lamp. (Refer to page 38.)  
G Adjust focus of a projector.  
G Make sure a projection screen is at least 4.1(1.2m) from the projector.  
G Check Projection Lens to see if it needs cleaning.  
Image is out of  
focus.  
NOTE : Moving a projector from a cool temperature location to a warm temperature location  
may result in moisture condensation on Projection Lens. In such an event, leave a  
projector OFF and wait until condensation disappears.  
G Check Ceiling / Rear feature. (See SETTINGsection on page 36.)  
Picture is Left/Right  
reversed.  
G Check Ceiling feature. (See SETTINGsection on page 36.)  
Picture is  
Top/Bottom  
reversed.  
G Check Display feature.(See SETTINGsection on page 36.)  
Some displays are  
not seen during the  
Operation.  
G Check the connection between your computer or video equipment and a projector.  
G When turning a projector on, it takes about 30 seconds to display an image.  
G Check the system that you select is corresponding with your computer or video  
equipment.  
No image.  
G Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).  
G Check audio cable connection from audio input source.  
G Adjust the audio source.  
No sound.  
G Press VOLUME (+) button.  
G Press MUTE button.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
Problem:  
Remote Control Unit  
does not work.  
Try these Solutions  
G Check the batteries.  
G Check ALL-OFF switch on Remote Control Unit is set to ON..  
G Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.  
G Make sure you are not too far from a projector when using Remote Control Unit.  
Maximum operating range is 16.4(5m).  
G Make sure the code of Remote Control Unit is set to conform to projector.  
(See SETTINGsection on page 36, 37.)  
G Check cable connection between a projector and your computer.  
G Check the mouse setting on your computer.  
G Turn a projector on before turning on a computer.  
Wireless Mouse  
function does not  
work.  
SERVICE  
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.  
You can often correct operating problems yourself. If the projector fails to work properly, see the "TROU-  
BLESHOOTING" section on pages 42 and 43.  
If after following all operating instructions, you find that service is necessary, contact the Christie Service Station  
or store where you purchased the unit.  
Give the model number and explain the difficulty. We will advise you how to obtain service.  
This symbol on the nameplate means the product is Listed by Underwriters  
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety  
standards against risk of fire, casualty and electrical hazards.  
The CE Mark is a Directive conformity mark of the European Community (EC).  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TECHNICAL SPECIFICATIONS  
Multi-media Projector  
Projector Type  
11.9" x 6.4" x 16.6" (302mm x 162mm x 422mm)  
17.2 lbs (7.8 kg)  
(W x H x D)  
Dimensions  
Net Weight  
0.99" TFT Active Matrix type, 3 panels  
1024 x 768 dots  
LCD Panel System  
Panel Resolution  
Number of Pixels  
Color System  
2,359,296 (1024 x 768 x 3 panels)  
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N  
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i  
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz  
Adjustable from 30to 300”  
High Definition TV Signal  
Scanning Frequency  
(Diagonal)  
Projection Image size  
Horizontal Resolution  
Projection Lens  
800 TV lines  
F 1.7 ~ 2.1 lens with f 34 mm ~ 44 mm with motor zoom and focus  
4.1~ 32.8(1.2 m ~ 10.0 m)  
Throw Distance  
250 W  
Projection Lamp  
(VGA) HDB 15-pin Terminal x 1  
DVI-I Terminal (Digital/Analog)  
Computer 1 Input Terminal  
Computer 2 Input Terminal  
Computer Audio Input Jacks  
Video Input Jacks  
Mini Jack (stereo) x 2 (Computer 1 and Computer 2)  
RCA Type x 1 (Video), RCA Type x 3 (Y, Pb/Cb, Pr/Cr),  
Mini DIN 4 pin x 1 (S-Video) and RCA x 2 (Audio R and L)  
(VGA) HDB 15-pin Terminal x 1  
Mini Jack (stereo) x 1  
Monitor Out Terminal  
Audio Output Jack  
Control Port Connector  
USB Connector  
Built-in Speakers  
Feet Adjustment  
Voltage and  
Mini DIN 8 pin x 1  
USB Series B receptacle x 1  
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)  
0˚ to 10˚  
AC 100 ~ 120 V (4.6 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)  
AC 200 ~ 240 V (2.3 A Max. Ampere), 50 / 60 Hz (Continental Europe)  
Power Consumption  
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)  
Operating Temperature  
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)  
Storage Temperature  
Remote Control Unit  
Power Source  
Operating Range  
Dimensions  
:
:
:
:
:
AA, UM3 or R06 Type x 2  
16.4(5m) / 30˚  
2.0x 1.4x 7.6(50mm x 36mm x 193mm)  
0.35 lbs (160 g) (including batteries)  
Net Weight  
(Max. Output : 1mW / Wave length : 650 20nm)  
Class II Laser  
Laser Pointer  
Users Manual  
AC Power Cord  
Accessories  
Remote Control Unit and Batteries  
VGA Cable  
USB Cable  
Control Cable for Serial port  
DVI/VGA Adapter  
Protective Dust Cover  
Lens Cover  
G The specifications are subject to change without notice.  
G LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a  
tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
CONFIGURATIONS OF TERMINALS  
COMPUTER INPUT-1 and MONITOR OUT TERMINALS (ANALOG)  
Terminal : HDB15-PIN  
1
2
3
4
5
6
7
8
Red Input  
Green Input  
Blue Input  
Sense 2  
9
+5V Power  
Pin Configuration  
10 Ground (Vert.sync.)  
11 Sense 0  
12 DDC Data  
2
1
5
4
3
10  
9
8
7
6
15  
14  
13  
12  
11  
Ground (Horiz.sync.) 13 Horiz. sync.  
Ground (Red)  
Ground (Green)  
Ground (Blue)  
14 Vert. sync.  
15 DDC Clock  
COMPUTER INPUT-2 TERMINAL (DIGITAL/ANALOG)  
Terminal : DVI-I 29-PIN  
Pin Configuration  
C1 Analog Red Input  
C1 C2  
C2 Analog Green Input  
C3 Analog Blue Input  
C4 Analog Horiz. sync  
1
9
2
3
4
5
6
7
8
10 11 12 13 14 15 16  
C5 Analog Ground (R/G/B)  
17 18 19 20 21 22 23 24  
1
2
3
4
5
6
7
8
T.M.D.S. Data2–  
9
T.M.D.S. Data1–  
17 T.M.D.S. Data0–  
18 T.M.D.S. Data0+  
T.M.D.S. Data2+  
10 T.M.D.S. Data1+  
T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield  
+3.3V MCI  
W-LAN  
C3 C4  
C5  
12 +5V MCI  
13 Card In  
14 +5V Power  
15 Ground (for +5V)  
16 Hot Plug Detect  
20 Viewer RXD  
21 Viewer TXD  
22 T.M.D.S. Clock Shield  
23 T.M.D.S. Clock+  
24 T.M.D.S. Clock–  
DDC Clock  
DDC Data  
Analog Vert. sync  
CONTROL PORT CONNECTOR  
Terminal : Mini DIN 8-PIN  
PS/2  
-----  
Serial  
R X D  
-----  
ADB  
-----  
Pin Configuration  
1
2
3
4
5
6
7
8
CLK  
ADB  
-----  
DATA  
GND  
-----  
-----  
GND  
8
7
6
GND  
-----  
5
4
3
RTS / CTS  
T X D  
2
1
-----  
-----  
GND  
-----  
GND  
-----  
GND  
GND  
USB CONNECTOR (Series B)  
Pin Configuration  
1
2
3
4
Vcc  
- Data  
+ Data  
Ground  
2
3
1
4
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
OPTIONAL PARTS  
The parts listed below are optionally supplied. When ordering those parts, give the name and Type No. to the sales dealer.  
G Control Cable (PS2 Port)  
G Control Cable (ADB Port)  
G MAC Adapter  
Type No. : POA-MCPS2  
Type No. : POA-MCMAC  
Type No. : POA-MACAP  
G HDB 15 pin-SCART 21 pin Cable Type No. : POA-CA-SCART  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDICATORS AND PROJECTOR CONDITION  
Check the Indicators for projector condition.  
Indicators  
Projector Condition  
WARNING  
READY  
TEMP.  
green  
LAMP  
REPLACE  
yellow  
LAMP  
red  
red  
The projector is OFF. (The AC Power Cord is unplugged.)  
The projector is READY to be turned on with the POWER ON-  
OFF button.  
The projector is operating normally.  
The temperature inside the projector is abnormally high. The  
projector cannot be turned on. When the projector is cooled  
down enough and the temperature returns to normal, the READY  
indicator lights green and the projector can be turned on. (The  
WARNING TEMP. indicator keeps flashing.) Check and clean  
the Air Filter.  
The projector is cooled down enough and the temperature  
returns to normal. When turning on the projector, the WARNING  
TEMP. indicator stops flashing. Check and clean the Air Filter.  
The projector is being cooled down. It cannot be turned on until  
the READY indicator lights green.  
The projector detects an abnormal condition and cannot be  
turned on. Unplug the AC Power Cord and plug it again to turn  
on the projector. If the projector is turned off again, disconnect  
the AC Power Cord and contact the dealer or the service center  
for service and checkup. Do not leave the projector on. It may  
cause electric shock or a fire hazard.  
The projector is in the Power management mode.  
• • • on  
• • • flashing  
• • • dim  
• • • off  
When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow,  
replace the projection lamp with a new one promptly. Reset the Lamp Replace Counter after replacement of the lamp.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHRISTIE DIGITAL SYSTEMS, Inc.  
627A Aljunied Road  
#05-02 Biz Tech Centre  
Singapore 389842  
Telephone 65-877-8737  
Fax 65-877-8747  
CHRISTIE DIGITAL SYSTEMS, Inc. CHRISTIE DIGITAL SYSTEMS, Inc. CHRISTIE DIGITAL SYSTEMS, Inc.  
CHRISTIE DIGITAL SYSTEMS, Inc.  
Willicher Damm 129  
D-41066 Mönchengladbach Germany  
Telephone +49 2161 664540  
Fax +49 2161 664546  
809 Wellington Street North  
Kitchener, Ontario  
Canada N2G 4Y7  
Telephone (519) 744-8005  
North America call toll-free  
1-800-265-2171 (sales)  
Fax (519) 749-3136  
10550 Camden Drive  
Cypress, CA 90630  
USA  
Telephone (714) 236-8610  
Fax (714) 503-3385  
Toll Free 1-800-407-7727  
Toll Free 1-800-333-3816  
ViewPoint  
200 Ashville Way  
Wokingham, Berkshire, U.K.  
RG41 2PL  
Telephone +44 118 977-8000  
Fax +44 118 977-8100  
Printed in Japan  
Part No. 10-A 610 309 0504 (1AA6P1P4198-- MH7KA)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin TV Video Accessories F1DC108B DR User Manual
BenQ Computer Monitor GW2255 User Manual
BenQ Projection Television PB2140 PB2240 User Manual
BenQ Projector MX511 User Manual
Blaupunkt Car Stereo System CD31 User Manual
Bowers Wilkins Speaker DM320 User Manual
Bradford White Corp Water Heater Electric Instantaneous Water Heaters User Manual
Brother Printer PT 330 User Manual
Casio Cash Register SE C6000 User Manual
Chauvet Landscape Lighting E 190WW User Manual