DMX-4 LED
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. BEFORE YOU BEGIN
What is included
1 x DMX-4 LED
1 x Power Cord
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure
that all parts are present, and have been received in good condition. Notify the shipper
immediately and retain packing material for inspection if any parts appear damaged from
shipping or the carton itself shows signs of mishandling. Save the carton and all packing
materials. In the event that a fixture must be returned to the factory, it is important that the fixture
be returned in the original factory box and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information
from the regular text.
MEANING
CONVENTION
[10]
<Menu>
1~512
50/60
A DIP switch to be configured
A key to be pressed on the fixture’s control panel
A range of values
A set of values of which only one can be chosen
A menu option not to be modified (for example, showing the operating
mode/current status)
Settings
MENU >
Settings
A sequence of menu options to be followed
A value to be entered or selected
ON
Icons
This manual uses the following icons to indicate information that requires special attention on the
part of the user.
MEANING
ICONS
This paragraph contains critical installation, configuration or operation
information. Failure to comply with this information may render the fixture
partially or completely inoperative, cause damage to the fixture or cause
harm to the user.
This paragraph contains important installation or configuration information.
Failure to comply with this information may prevent the fixture from
functioning correctly.
This paragraph reminds you of useful, although not critical, information.
1. Before You Begin
3
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Please read these instructions carefully. It includes important information
about the installation, usage and maintenance of this product.
Please keep this User Manual for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line
voltage you are connecting to is not higher than that stated on the decal or rear panel
of the fixture.
This product is intended for indoor use only! To prevent risk of fire or shock, do not
expose fixture to rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing fuse and be sure to
replace with same fuse source.
Secure fixture to fastening device using a safety chain.
Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at
temperatures higher than this.
In the event of a serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Never carry the fixture directly from the cord. Always use the hanging/mounting
bracket.
Avoid direct eye exposure to the light source while it is on.
1. Before You Begin
4
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
3. SETUP
AC Power
This fixture accepts an input of 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure
the line voltage to which you are connecting it is within the range of accepted voltages. Also
make sure that the fixtures you are plugging into the DMX-4 LED match the input voltage.
Input voltage equals output voltage.
To determine the power requirements for a particular fixture, see the label affixed to the back
plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating
indicates its average current draw under normal conditions.
Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only
as a 0 to 100% switch.
Always connect the fixture to a circuit with a suitable electrical ground.
Notes on “Switch” Operation
Dimmer/switch packs are primarily intended for lamp-based PAR cans. Connecting a fixture
equipped with an electronic (switching) power supply to a dimmer/pack switch may damage the
fixture or make it work erratically.
The improved DMX-4 LED’s design now allows you to switch on and off loads equipped with
electronic power supplies, such as LED-based luminaries or laser fixtures. However, the DMX-4
LED must be in “switch” mode before connecting this type of loads to it. Please see the
instructions on how to set the DMX-4 LED in switch mode below.
Always make sure that the DMX-4 LED is in switch mode before connecting a load
equipped with an electronic power supply to it. Doing otherwise could damage the load.
Changing between “Dimmer” and “Switch”
The DMX-4 LED has two different methods for controlling the output of the four (4) channels. This
must be set by the user via the control panel.
Please see the steps below for this procedure.
1. Unplug any units from the four output channels.
2. Plug the DMX-4 LED into power.
3. Press <MODE> until ~ appears on the LED display.
4. Press <MENU> until **/**/**/** appears on the LED display. This setting can
be set differently for each of the four channels. Navigate to the desired channel.
5. Using <UP> & <DOWN>, select either or . switches the channel to “switch”
method. sets it into dimmer method.
6. Continue to set this for each of the 4 channels, using the process detailed in the steps
above, until complete.
3. Setup
6
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting
Orientation
The DMX-4 LEDmay be mounted in any position, provided there is adequate room for ventilation.
Rigging
Be sure that the structure can support the weight of the fixture. Please see the “Technical
Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. This
may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13 mm
in size. When rigging consider routine maintenance and control panel access. Please see the
following notes on installation.
The back plate may be reversed for an alternate rigging configuration. See the section
on the following page for details on how to do this.
Safety cables must always be used.
Mounting bracket
3. Setup
7
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Rigging
The DMX-4 LED ships ready to mount a standard clamp directly to the mounting bracket.
However, if you are using this product with truss or a lighting stand, then there is an alternate
rigging configuration available. This option is ideal for hanging the product without using a
hanging clamp.
Please see the steps below for further details.
1. Unplug power from the product.
2. On the back of the product, locate the six (6) Edison #2 screws.
3. Using a screwdriver, remove these.
4. The mounting bracket will now come off. Be careful not to damage the internal
components of the dimmer, as they are exposed during this step!
5. Flip the mounting bracket (back panel) around.
6. Reattach the panel by securely installing the six (6) screws.
Remove these six
(6) screws
Back Panel
Alternate Rigging
Configuration
3. Setup
8
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
4. OPERATING INSTRUCTIONS
Configuring the Starting Address
The DMX-4 LEDfixture uses up to four DMX channels. The highest channel that the fixture may
be set to in order to function properly is 509. Any address higher than this will prevent access to
all of the channels.
If this is your first time using DMX, we recommend reading the “DMX Primer” section in the
“Appendix”.
DMX Mode
This is the operating mode which will allow for control with an external DMX controller. You must
set the starting address and personality for this mode.
Please see the instructions below.
1. Press <MODE> to switch between “DMX Mode” and “Standalone Mode”. Switch it to
“DMX Mode”.
2. Press <MENU> until the LED display reads ~.
3. Using <UP> and <DOWN>, select one of the three personalities.
4. Press <MENU> until the LED display reads ~.
5. Using <UP> and <DOWN>, select the DMX starting address.
Standalone Mode
This fixture has built-in auto programs with adjustable settings.
Please see the instructions below.
1. Press <MODE> to switch between “DMX Mode” and “Standalone Mode”. Switch it to
“Standalone Mode”.
2. Press <MENU> until the LED display reads ~.
3. Using <UP> and <DOWN>, select one of the programs.
4. Press <MENU> until the LED display reads ~.
5. Using <UP> and <DOWN>, select the desired run speed.
6. Press <MENU> until the LED display reads ~.
7. Using <UP> and <DOWN>, select the desired dimmer level for the program currently
running.
Menu Map
MODE
MENU
DISPLAY
DESCRIPTION
Starting address
~
1-channel mode
2-channel mode
4-channel mode
Channel 1 function
Channel 2 function
Channel 3 function
Channel 4 function
Personality
DMX Mode
Switch/Dimmer
Switch:
Dimmer:
Program
~
~
~
Standalone Mode
Run speed
Dimmer
Slow~fast
4. Operating Instructions
9
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
DMX Channel Values
4-Channel Personality
In this DMX personality, the four channels will be controlled by separate DMX channels.
CHANNEL
1
VALUE
FUNCTION
Dimmer
000 255 0%~100%
Dimmer
000 255 0%~100%
2
3
4
Dimmer
000 255 0%~100%
Dimmer
000 255 0%~100%
2-Channel Personality
In this DMX personality, the four channels will be grouped into pairs. Channels 1+2 will be
controlled by DMX channel 1, while channels 3 + 4 will be controlled by DMX channel 2.
CHANNEL
1
VALUE
FUNCTION
Dimmer
000 255 0%~100%
Dimmer
000 255 0%~100%
2
1-Channel Personality
In this DMX personality, the four channels will be grouped together. Channels 1+2+3+4 will all be
controlled by DMX channel 1.
CHANNEL
1
VALUE
FUNCTION
Dimmer
000 255 0%~100%
4. Operating Instructions
10
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
5. APPENDIX
General Troubleshooting
SYMPTOM
POSSIBLE CAUSE(S)
POSSIBLE ACTION(S)
Check total load placed on the
electrical circuit.
Excessive circuit load
Breaker/Fuse
keeps blowing
Short circuit along the power
wires
Check for a short in the electrical
wiring (internal and/or external).
No power
Loose power cord
Check for power on Mains.
Check power cord
Device does not
power up
Check Control Panel and unit
addressing
Wrong DMX addressing
Damaged DMX cables
Wrong polarity settings on the
controller
Check DMX cables
Check polarity switch settings on
the controller
Fixture is not
responding to DMX
Loose DMX cables
Faulty DMX interface
Faulty Main PCB
Check cable connections
Replace DMX input
Replace Main PCB
Non DMX cables
Bouncing signals
Use only DMX compatible cables
Install terminator as suggested.
Install amplifier right after fixture
with strong signal.
Install an optically coupled DMX
splitter after unit #32.
Long cable / Low level signal
Too many fixtures
Loss of signal
Keep DMX cables separated from
power cables or black lights.
Interference from AC wires
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support.
5. Appendix
11
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
DMX Primer
There are 512 channels in a DMX connection. A fixture capable of receiving DMX will require one
or a number of sequential channels. The user must assign a starting address on the fixture that
indicates the first channel reserved in the controller. There are many different types of DMX
controllable fixtures and they all may vary in the total number of channels required. Choosing a
start address should be planned in advance. Channels should never overlap. If they do, this will
result in erratic operation of the fixtures whose starting address is set incorrectly. You can
however, control multiple fixtures of the same type using the same starting address as long as the
intended result is that of unison movement or operation. In other words, the fixtures will all
respond exactly the same.
DMX fixtures are designed to receive data through a daisy chain. A daisy chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in
which the fixtures are connected is not important and has no effect on how a controller
communicates to each fixture. Use an order that provides for the easiest and most direct cabling.
Connect fixtures using shielded two conductor twisted pair DMX data cable with three pin XLR
male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and
pin 3 is Data positive (S+).
Fixture Linking (Daisy Chain)
You will need a daisy chain to run light shows of one or more fixtures using a DMX controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a daisy chain determines the number
of fixtures the data link can support.
To comply with the EIA-485 standard, do not connect more than 32 fixtures on one daisy
chain. Connecting more than 32 fixtures on one daisy chain without the use of a DMX
optically-isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended cable distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a daisy chain: 32
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified
DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create
your own cable please use data-grade cables that can carry a high quality signal and are less
prone to electromagnetic interference.
DMX Data Cable
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485
applications. Standard microphone cables cannot transmit DMX data reliably over long distances.
The cable must have the following characteristics:
Type:
shielded, 2-conductor twisted pair
30 pF/ft
Maximum capacitance between conductors:
Maximum capacitance between conductor and shield:
Maximum resistance:
Nominal impedance:
55 pF/ft
20 ohms/1000 ft
100 ~ 140 ohms
5. Appendix
12
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR
connector on the other end.
DMX connector configuration
COMMON
DMX +
1
3
1
3
INPUT
OUTPUT
2
2
DMX -
Terminator
To avoid signal transmission problems
and interference, it is always advisable to
connect a DMX signal terminator.
1
3
2
120 ohm ¼ W resistor
between pin 2 (DMX -) and
pin 3 (DMX +) on the
output of the last fixture
Do not allow contact between the common and the fixture’s chassis ground. Grounding
the common can cause a ground loop, and your fixture may perform erratically. Test
cables with an ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
Setting the Starting Address
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a
start address from 1~512. A fixture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a fixture that uses six DMX
channels and was addressed to start on DMX channel 100, would read data from channels: 100,
101, 102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap,
and note the start address selected for future reference.
If this is your first time addressing a fixture using the DMX control protocol, we suggest jumping
to the “Appendix” section and reading the heading “DMX Primer”. It contains very useful
information that will help you understand its use.
5. Appendix
13
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
3-Pin to 5-Pin Conversion Chart
If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to
3-pin adapter. The chart below details a proper cable conversion:
3-PIN TO 5-PIN CONVERSION CHART
Conductor
3-Pin Female (Output)
Pin 1
5-Pin Male (Input)
Pin 1
Ground/Shield
Data ( - ) signal
Data ( + ) signal
Not used
Pin 2
Pin 3
Pin 2
Pin 3
Pin 4
Pin 5
Not used
Setting up a DMX Daisy Chain
1. Connect the (male) 3-pin connector side of
Universal DMX Controller
the DMX cable to the output (female) 3-pin
connector of the controller.
2. Connect the end of the cable coming from the
controller which will have a (female) 3-pin
connector to the input connector of the next
fixture consisting of a (male) 3-pin connector.
This drawing
3. Then, proceed to connect from the output as
stated above to the input of the following
fixture and so on.
provides a general
illustration of the
DMX input/output
panel of a lighting
fixture.
Continue the link
5. Appendix
14
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently.
Usage and environment are contributing factors in determining frequency. As a general rule,
fixtures should be cleaned at least twice a month. Dust build up reduces light output performance
and can cause overheating. This can lead to reduced lamp life and increased mechanical wear.
Be sure to power off fixture before conducting maintenance.
Unplug fixture from power.
Use a vacuum or air compressor and a soft brush to remove dust collected on external
vents.
Clean all lenses when the fixture is cool with a mild solution of glass cleaner or
Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue.
Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
Gently polish optical surfaces until they are free of haze and lint.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not be
issued. Package must be clearly labeled with a Return Merchandize Authorization Number (RMA
#). Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA #
prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief
description of the cause for the return. Be sure to pack fixture properly; any shipping damage
resulting from inadequate packaging is the customer’s responsibility. As a suggestion, proper
UPS packing or double-boxing is always a safe method to use. CHAUVET® reserves the right to
use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of paper
inside the box:
1)
2)
3)
4)
5)
Your name
Your address
Your phone number
The RMA #
A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify
and submit claims with the shipper in the event that a fixture is damaged due to shipping. Any
other claim for items such as missing component/part, damage not related to shipping, and
concealed damage, must be made within seven (7) days of receiving merchandise.
5. Appendix
15
12/10/2010 5:16 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
WEIGHT & DIMENSIONS
Length.......................................................................................................... 8.3 in (210 mm)
Width ........................................................................................................... 7.7 in (194 mm)
Height ............................................................................................................ 2.8 in (70 mm)
Weight ..............................................................................................................5 lbs (2.2 kg)
POWER
Input power.....................................................................................100~240 VAC, 50/60 Hz
Output voltage to fixtures ............................................... Input voltage equals output voltage
Output current (max per channel).....................................................................................5 A
Output current (max total) ..............................................................................................15 A
Fuse size .......................................................................................................... F 6 A, 250 V
INDOOR/OUTDOOR
Rating.....................................................................................................For indoor use only
THERMAL
Maximum ambient temperature...................................................................... 104° F (40° C)
CONTROL & PROGRAMMING
Data input ........................................................................... locking 3-pin XLR female socket
Data output............................................................................ locking 3-pin XLR male socket
Data pin configuration .............................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocol ...................................................................................................... DMX-512 USITT
DMX Channels (user-configurable) ..............................................................................1, 2, 4
ORDERING INFORMATION
DMX-4 LED.......................................................................................................... DMX4LED
WARRANTY INFORMATION
Warranty........................................................................................... 2-year limited warranty
CONTACT US
WORLD WIDE
General Information ........................................................................................... CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954-929-1115
fax: 954-929-5560
toll free: 800-762-1084
Technical Support.............................................................................................. CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954-929-1115 (Press 4)
fax: 954-929-5560 (Attention: Service)
World Wide Web................................................................... http://www.chauvetlighting.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|