Bradley Smoker Network Card 1734 AENT User Manual

POINT I/O

EtherNet/IP

Adapter Module

1734-AENT

User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of Changes

This publication contains new and revised information not in the last

release.

New and Revised Information

See the table for a summary of the major changes in this manual.

Chapter

Revised to include

Chapter 6 - LED Status Indicators

Appendix A - Adapter Web Pages

New column on recommended actions

Latest adapter Web pages

Change Bars

Change bars (as shown with this paragraph) show the areas in this

manual that are different from previous editions and indicate the

addition of new or revised information.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of Changes

Notes:

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Preface

What This Preface Contains . . . . . . . . . . . . . . . . . . . . . . . . P-1

Who S h ould Use This M a nual . . . . . . . . . . . . . . . . . . . . . . P-1

C o mmon Techniques Used in This M a nual. . . . . . . . . . . . . P-1

How To Use This M a nual . . . . . . . . . . . . . . . . . . . . . . . . . P-2

A b out the E xample A p p l ications. . . . . . . . . . . . . . . . . . P-2

System Components. . . . . . . . . . . . . . . . . . . . . . . . . . . P-3

Where to Find M o re Information . . . . . . . . . . . . . . . . . . . . P-4

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-5

C h apter 1

A b out the A d apter

What This Chapter Contains . . . . . . . . . . . . . . . . . . . . . . . 1-1

Important A d apter C o nsiderations . . . . . . . . . . . . . . . . . . . 1-1

S e t the Chassis S ize . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

A d apter R e placemen t . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -2

E m pty S l o ts and R IUP Sit u ation s . . . . . . . . . . . . . . . . . . 1 -2

Cycle Power To a System For the First Time . . . . . . . . . 1-4

A d apter Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Hardware/S o f tware Compatibility . . . . . . . . . . . . . . . . . . . 1-5

What the A d apter Does . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Use of the Common Industrial Protocol (CIP). . . . . . . . . . . 1-5

Understand the Producer/Consumer M o del . . . . . . . . . . . . 1-6

S p ecify the R e quested Packet Interval (R PI) . . . . . . . . . . . . 1-6

S u pport of R a ck-optimized and Direct Connections . . . . . . 1-7

Mix R a ck-optimized and Direct Connections . . . . . . . . . 1-7

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Determine Compatibility . . . . . . . . . . . . . . . . . . . . . . . 1-8

Understand M e ssaging . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Establish I /O C o nnections . . . . . . . . . . . . . . . . . . . . . . 1-8

C o n f igure Autobaud. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

C h apter 2

Install the A d apter

What This Chapter Contains . . . . . . . . . . . . . . . . . . . . . . . 2-1

Identify A d apter C o mponents. . . . . . . . . . . . . . . . . . . . . . 2-1

M o unt the A d apter on a DIN R a il Before Installing M o dules 2-2

M o unt (or R e place) the A d apter to an Existing S yste m . . . . 2 -3

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

M o unting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

C h apter 3

Configure the Adapter for Your

EtherNet/IP Network

What This Chapter Contains . . . . . . . . . . . . . . . . . . . . . . . 3-1

C o n f iguration R e quirements . . . . . . . . . . . . . . . . . . . . . . . 3-2

IP A d dres s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 -3

Gateway A d dress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

S u bnet M a sk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

S e t the Network A d dress . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Use the R o ckwell BootP /D HCP Utility . . . . . . . . . . . . . . . . 3-8

S a ve the R e lation L i st . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Use DHCP Software to Configure Your Adapter . . . . . . . . . 3-11

C h apter 4

Configure the Adapter for Direct

C o nnection in R S L o gix 5000

Software

What This Chapter Contains . . . . . . . . . . . . . . . . . . . . . . . 4-1

S e t Up the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Create the Example A p p l ication . . . . . . . . . . . . . . . . . . . . . 4-2

C o n f igure the I /O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -4

Add the Local EtherNet/IP Bridge to the

I /O C o n f iguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

A d d the POINT I /O A d apter to the I/O Configuration . . 4-7

A d d the POINT I /O M o dules to the I /O C o n f iguration. . 4-10

E d it the Controller Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Create the L a dder Program . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Download the Program to the Controller . . . . . . . . . . . . . . 4-18

V e rify the M o dule Chassis S ize . . . . . . . . . . . . . . . . . . . . . 4-20

C o n f igure the A d apter with Fixed IP A d dress . . . . . . . . . . . 4-22

R e cover From an Overloaded A d apter . . . . . . . . . . . . . . . . 4-24

C h apter 5

Configure the Adapter for Direct

C o nnection and R a ck O p timization

in RSLogix 5000 Software

What This Chapter Contains . . . . . . . . . . . . . . . . . . . . . . . 5-1

S e t Up the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Create the Example A p p l ication . . . . . . . . . . . . . . . . . . . . . 5-3

C o n f igure the I /O M o dules . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Add the Local EtherNet/IP Bridge to the

I /O C o n f iguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

A d d the POINT I /O A d apter to the I/O Configuration . . 5-7

Add the POINT I/O Module and Configure for Direction

C o nnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

Add the POINT I/O Module and Configure For Rack

Optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

Download the Program to the Controller . . . . . . . . . . . . . . 5-17

V e rify the M o dule Chassis S ize . . . . . . . . . . . . . . . . . . . . . 5-18

A c cess M o dule Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

iii

C h apter 6

LED S tatus Indicators

A d apter Web Pages

What This Chapter Contains . . . . . . . . . . . . . . . . . . . . . . . 6-1

Interpret the S tatus Indicators . . . . . . . . . . . . . . . . . . . . . . 6-1

A p pendix A

What This A p pendix C o ntains . . . . . . . . . . . . . . . . . . . . . . A -1

Work with the Home Page . . . . . . . . . . . . . . . . . . . . . . . . A -1

Work with the Diagnostics Pages. . . . . . . . . . . . . . . . . . . . A -3

Use the Diagnostic Overview Page . . . . . . . . . . . . . . . . A -4

Use the Network S e ttings Page . . . . . . . . . . . . . . . . . . . A -5

Use the Ethernet S tatistics Page . . . . . . . . . . . . . . . . . . A-6

Use the I /O C o nnections Page . . . . . . . . . . . . . . . . . . . A -8

Use the Diagnostic M e ssaging Page . . . . . . . . . . . . . . . A -9

Work with the Configuration Pages . . . . . . . . . . . . . . . . . A -10

Use the Identity Page . . . . . . . . . . . . . . . . . . . . . . . . . A -11

Use the Network Configuration Page . . . . . . . . . . . . . A -12

Use the Services Page . . . . . . . . . . . . . . . . . . . . . . . . A -14

Work with the Browse Chassis Page . . . . . . . . . . . . . . . . A -15

A p pendix B

Configure the RSLinx Ethernet

Communication Driver

What This A p pendix C o ntains . . . . . . . . . . . . . . . . . . . . . . B-1

Install the R SLi n x S o f tware . . . . . . . . . . . . . . . . . . . . . . . . B-1

C o n f igure the A B_ETH Driver . . . . . . . . . . . . . . . . . . . . . . B-2

C o n f igure the A B_ETH /I P Driver . . . . . . . . . . . . . . . . . . . . B-4

A p pendix C

1734 POINT I/O Module/RSLogix

5000 Controller Tag Reference

What This A p pendix C o ntains . . . . . . . . . . . . . . . . . . . . . . C-1

1734 POINT I /O C atalog Number s . . . . . . . . . . . . . . . . . . . C -1

V a lid Number R a nges for R SL o gix 5000 Data Types . . . . . . C-2

Digital 2 POINT Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Digital 4 POINT Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Digital 2 POINT Output – Without Diagnostic S tatus. . . . . . C-5

Digital 2 POINT Output – With Over Load and Open Load

Diagnostic S tatus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6

Digital 2 POINT Output – With Over L o ad Diagnostic S tatus C-7

Digital 4 POINT Output – With Over Load and Open Load

Diagnostic S tatus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

Digital 4 POINT Output – With Over L o ad Diagnostic S tatus C-9

A n alog 2 Channel Input . . . . . . . . . . . . . . . . . . . . . . . . . C-10

A n alog 2 Channel Output . . . . . . . . . . . . . . . . . . . . . . . . C-19

S p ecialty I /O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C -23

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

A p pendix D

Q u ick Start

What This A p pendix C o ntains . . . . . . . . . . . . . . . . . . . . . . D-1

Necessary Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . D-1

C o n f igure the A d apter. . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2

E n ter A d apter Properties . . . . . . . . . . . . . . . . . . . . . . . D-3

A d d A n other M o dule Under the A d apter. . . . . . . . . . . . D-4

C o n f igure 1734 POINT I /O M o dules . . . . . . . . . . . . . . . . . D-5

C o n f igure an Ethernet Driver in R SLi n x S o f tware . . . . . . . . D-8

L a unch R SLi n x S o f tware . . . . . . . . . . . . . . . . . . . . . . . . D-8

A d d the A B_ETHIP-1 (EtherNet /I P) Driver . . . . . . . . . D-10

Index

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

This preface describes how to use this manual. See the table for a list

of where to find specific information within this chapter.

What This Preface Contains

For Information About

See Page

Preface 1

Preface 2

Preface 3

Preface 4

Preface 5

Who Should U s e T h is Manual

C o mmon T e chniques U s ed in T h is Manual

H o w T o U s e T h is Manual

A b out the E x a m ple A p plications

System C o mponents

Where to F i nd More Information

T e rminology

We wrote this manual for control engineers and technicians who are

installing, configuring, and maintaining an EtherNet/IP control system

that communicates with POINT I/O modules through a 1734-AENT

adapter. We assume you have a good understanding of Ethernet

networks and the TCP/IP protocol.

Who Should Use This

Manual

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

We use the following conventions throughout this manual.

• Numbered lists provide sequential steps.

Common Techniques Used

in This Manual

• Bulleted lists provide information, not procedural steps.

The screen captures shown in this manual are

pictures of the software’s actual screens.

This symbol identifies helpful tips.

TIP

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

This manual contains an overview of the 1734-AENT adapter. It

describes how to install and configure the adapter and provides

examples showing how to use the adapter to communicate with

POINT I/O modules over an EtherNet/IP network.

How To Use This Manual

About the Example Applications

This manual presents two example applications that demonstrate the

procedures for configuring and communicating with POINT I/O

modules using the 1734-AENT adapter. We intend the example

applications as building blocks to help you get your own system up

and running. We recommend that you set up and run the example

applications and use them as guides.

Here is the type of system you’ll be setting up.

1734-AENT

10.88.70.2

POINT I/O

Slot 0 1 2 3

Local

Chassis

Data

1756-ENBT

10.88.70.4 (slot 3)

Slot 0 1 2 3 4

Logix5555

Controller (slot 1)

Switch

10.88.70.26

Programming

Terminal

31393-M

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

System Components

We used the following components for the example applications. You

need the same or similar components to set up your own control

system using POINT I/O modules on an EtherNet/IP network.

Quantity Product Name

Hardware

Catalog Number

POINT I/O EtherNet/IP adapter

POINT I/O 24V dc sink output module

1734-AENT

1734-OV4E/C

POINT I/O relay output module

DIN rail

1734-OW2/C

199-DR1 or equivalent

1756-A4, (or 1756-A7, 1756-A13,1756-A17)

1756-PA72, (or 1756-PB72)

1756-L55

ControlLogix chassis

ControlLogix power supply

Logix5555 controller

ControlLogix EtherNet/IP bridge module

1756-ENBT

Personal computer that supports RSLogix 5000 software Any appropriate model running Windows NT 4.0, Service Pack 6A

or higher

Ethernet switch

Refer to manufacturer’s specifications

1734-EP24DC

24V dc power supply

Associated media and connectors as needed

Software

RSLinx communications software,

version 2.31.00 or later

9355-WAB, 9355-WABOEM, 9355-WABC

9324-RLD300ENE

RSLogix 5000 programming software,

version 11.11 or later

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

Refer to the following Rockwell publications as needed for additional

help when setting up and using your EtherNet/IP network.

Where to Find More

Information

For Information About

See This Publication

Publication Number

ENET-AP001

Using EtherNet/IP for industrial control EtherNet/IP Performance and Application Guide

EtherNet/IP media

EtherNet/IP Media Planning and Installation Guide

ENET-IN001

Ethernet Communication Interface Module Installation

Instructions

1756-IN053

Ethernet communication interface

modules

Ethernet Communication Interface Module User Manual

Ethernet Communication Interface Module Release Notes

ControlLogix Chassis Installation Instructions

ControlLogix Power Supplies Installation Instructions

Logix5555 Controller User Manual

1756-UM051

1756-RN053

ControlLogix chassis

1756-IN080 (series B)

1756-5.67 (PA72/PB72)

1756-UM523

ControlLogix power supplies

Logix5555 programmable controllers

SoftLogix5800 Controller

SoftLogix5800 User Manual

1789-UM002 (L10, L30, L60)

ControlLogix EtherNet/IP bridge module ControlLogix EtherNet/IP Bridge Module Installation Instructions 1756-IN019

with firmware revision 2.3 or later

RSLogix 5000 programming software Getting Results with RSLogix 5000, version 3.2.1 or later

1734-AENT adapter POINT I/O EtherNet/IP Adapter Installation Instructions

POINT I/O digital and analog modules POINT I/O Digital and Analog Modules and PointBLOCK I/O

9399-RLD300GR

1734-IN590

1734-UM001

and PointBLOCK I/O modules

Modules User Manual

POINT I/O interface modules

POINT I/O RS-232 ASCII Module User Manual

POINT I/O RS-232 ASCII Module Installation Instructions

1734-UM009

1734-IN588

1734-IN058

POINT I/O expansion power supply

POINT I/O 24V dc Expansion Power Supply Installation

Instructions

POINT I/O field potential distributor

POINT I/O input modules

POINT I/O Field Potential Distributor Installation Instructions

POINT I/O 120V ac Input Module Installation Instructions

POINT I/O Input Module Installation Instructions

1734-IN059

1734-IN010

1734-IN051

1734-UM006

1734-IN005

1734-IN008

1734-IN011

POINT I/O encoders/counter modules POINT I/O Encoders/Counter Module User Manual

POINT I/O Encoders/Counter Module Installation Instructions

POINT I/O 22V ac input module

POINT I/O 220V ac Input Module Installation Instructions

POINT I/O RTD and isolated

thermocouple input module

POINT I/O RTD and Isolated Thermocouple Input Module

Installation Instructions

POINT I/O thermocouple and RTD input Thermocouple and RTD Input Module User Manual

module

1734-UM004

POINT I/O IV2 and IV4 input module

POINT I/O Input Module Installation Instructions

1734-IN052

POINT I/O 120/220V ac Output module POINT I/O 120/220V ac Output Module Installation Instructions 1734-IN009

POINT I/O protected output module

POINT I/O Protected Output Module Installation Instructions

1734-IN056

1734-IN586

POINT I/O Protected Output Module Installation Instructions

(OB2EP)

POINT I/O voltage output analog

module

POINT I/O 2 Voltage Output Analog Module Installation

Instructions

1734-IN002

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

For Information About

See This Publication

Publication Number

POINT I/O protected sink output module POINT I/O Protected Sink Output Module Installation Instructions 1734-IN585

POINT I/O 2 relay output module

POINT I/O 2 Relay Output Module Installation Instructions (OX2) 1734-IN587

POINT I/O 2 Relay Output Module Installation Instructions (OW2) 1734-IN055

POINT I/O synchronous serial interface POINT I/O Synchronous Serial Interface Absolute Encoder

absolute encoder module Module Installation Instructions

1734-UM007

POINT I/O cold junction compensation POINT I/O Cold Junction Compensation Wiring Base Assembly 1734-IN583

wiring base assembly

Installation Instructions

POINT I/O wiring base assembly

Very high speed-counter module

POINT I/O Wiring Base Assembly Installation Instructions

1734-IN013

1734-IN003

POINT I/O Very High-speed Counter Module Installation

Instructions

Very High-speed Counter Module User Manual

RSLinx Getting Results Guide

1734-UM003

RSLinx

LNXENT-GR001

Many of these publications are available online from:

http://literature.rockwellautomation.com/

TIP

Rockwell Software products contain extensive

tutorials and help screens. We recommend that you

use the tutorials and help screens to learn about

these products.

TIP

For more information about Rockwell Software

products, visit the Rockwell Software internet site:

http://www.software.rockwell.com

Refer to the table for the meaning of common terms.

Terminology

This Term

Means

BootP

BootP (Bootstrap Protocol) is a low-level protocol that provides

configurations to other nodes on a TCP/IP network. BootP

configuration files let you automatically assign IP addresses to an

Ethernet module (you can also obtain subnet masks and gateway

addresses from BootP).

Bridge

CIP

A node between two similar communication subnets where protocol

translation is minimal.

Control and information protocol, the EtherNet/IP application layer

uses the producer/consumer networking model. In this model one

producer broadcasts (multicasts) the data once to all the consumers.

All consumers see the data simultaneously and may choose whether

to consume (receive) the data or not. Delivery time is consistent, no

matter how many consumers there are.

Connection

The communication mechanism from the controller to another

module in the control system, usually used to exchange I/O data.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

This Term

consumer

CSMA/CD

Means

A destination device in the CIP networking model. See CIP.

Carrier sense multiple access/collision detection is the access

method used in Ethernet. When a device wants to gain access to the

network, it checks to see if the network is quiet (senses the carrier).

If it is not, it waits a random amount of time before retrying. If the

network is quiet and two devices access the line at exactly the same

time, their signals collide. When the collision is detected, they both

back off and each waits a random amount of time before retrying.

Determinism

DHCP

The ability to predict when information will be delivered. Important in

time-critical applications.

The dynamic host configuration protocol is an Internet protocol,

similar to BootP, for automating the configuration of computers that

use TCP/IP. DHCP can be used to automatically assign IP addresses,

to deliver IP stack configuration parameters, such as the subnet mask

and default router, and to provide other configuration information,

such as the addresses for printer, time, and news servers.

The 1734-AENT factory default is DHCP enabled. When you apply

power, the module sends a message containing its hardware address

to any DHCP server on the network. The server(s) replies by sending a

message with an appropriate IP address for the adapter. The adapter

responds by acknowledging to a server that it will use the offered IP

address.

DNS

The domain name system is a hierarchical, distributed method of

organizing the name space of the Internet. The DNS administratively

groups hosts into a hierarchy of authority that allows addressing and

other information to be widely distributed and maintained. A big

advantage to the DNS is that using it eliminates dependence on a

centrally-maintained file that maps host names to addresses.

Ethernet

A physical layer standard using carrier sense multiple access with

collision detection (CSMA/CD) methods.

EtherNet/IP

Ethernet industrial protocol applies a common application layer (CIP)

over Ethernet by encapsulating messages in TCP/UDP/IP.

Ethernet network

Explicit messaging

A local area network designed for the high-speed exchange of

information between computers and related devices.

Non-time critical messaging used for device configuration and data

collection, such as downloading programs or peer-to-peer messaging

between two PLC units.

Full duplex

A mode of communication that allows a device to send and receive

information at the same time, effectively doubling the bandwidth.

Fully qualified

domain name

A fully qualified domain name (FQDN) is a domain name that includes

all higher level domains relevant to the entity named. If you think of

the DNS as a tree-structure with each node having its own label, a

fully qualified domain name for a specific node would be its label

followed by the labels of all the other nodes between it and the root

of the tree. For example, for a host, a FQDN would include the string

that identifies the particular host, plus all domains of which the host

is a part, up to and including the top-level domain (the root domain is

always null). For example, PARIS.NISC.SRI.COM is a fully qualified

domain name for the host at 192.33.33.109.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

This Term

Means

Gateway

A module or set of modules that allows communications between

nodes on dissimilar networks.

Hardware address

Each Ethernet device has a unique hardware address (sometimes

called a MAC address) that is 48 bits. The address appears as six

digits separated by colons (such as, xx:xx:xx:xx:xx:xx). Each digit has a

value between 0 and 255 (0x00 to 0xFF). This address is assigned in

the hardware and cannot be changed. The hardware address is

required to identify the device if you are using a BOOTP utility.

Host name

The host name is the unique name for a computer within its domain.

It's always the first element of a full name, and, with its domain and

top-level domain suffix, creates the unique name of that computer on

the Internet. For example, let's say a trading website is

www.trading.com. The host name is www, which is not unique on

the web, but is unique within the trading domain.

The host name can also refer to the fully qualified domain name

(FQDN), or in this example, www.trading.com. Both naming methods

seem to be used interchangeably in various documents. For the

purposes of this document, the host name will refer to the FQDN, or

as in this example, www.trading.com.

Hub

A central connecting device that joins devices together in a star

configuration. Hubs are generally not suitable for use in I/O control

systems, since they are time-critical applications that cannot tolerate

lost packets.

Implicit messaging

Real-time messaging of I/O data.

Internet protocol that provides the routing mechanism for messages.

All messages contain not only the address of the destination station,

but the address of a destination network, which allows messages to

be sent to multiple networks within an organization or around the

world.

IP address

A 32-bit identification number for each node on an Internet Protocol

network. These addresses are represented as four sets of 8-bit

numbers (numbers from 0 to 255), with decimals between them. Each

node on the network must have a unique IP address.

Latency

The time between initiating a request for data and the beginning of

the actual data transfer.

Multicast

In the CIP producer/consumer model, one producer multicasts

(broadcasts) the data once to all the consumers.

Producer

The source of information in the CIP networking model. See CIP.

A physical and logical collection of application modules.

Rack-optimized

Subnet mask

An extension of the IP address that allows a site to use a single net

ID for multiple networks.

Switch

A network device that cross connects devices or network segments.

A switch provides each sender/receiver the full network bandwidth

(2x in full duplex mode), reduces collisions, and increases

determinism.

TCP

The transport control protocol is a more reliable but slower transport

protocol than UDP. It is used for explicit (not time critical) messaging

in EtherNet/IP.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

This Term

Means

TCP/IP

The transmission control protocol/internet protocol is a

transport-layer protocol (TCP) and a network-layer protocol (IP)

commonly used for communication within networks and across

internetworks.

Transaction

UDP

An exchange of request and data and response and data.

The user datagram protocol (UDP) is a transport protocol that

provides a very simple but fast capability to send datagrams between

two devices. It is used for I/O (implicit) messaging in EtherNet/IP.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter

About the Adapter

This chapter provides an overview of the 1734-AENT POINT I/O

What This Chapter Contains

EtherNet/IP adapter, its primary features, and how to use it. You need

to understand the concepts discussed in this chapter to configure your

adapter and use it in an EtherNet/IP control system. See the table for a

list of where to find specific information in this chapter.

For Information About

See Page

1-1

Important A d apter C o nsiderations

Set the C h assis Size

1-1

A d apter R e placement

1-2

Emp t y Slots and R IUP S ituations

Cycle Power T o a S ystem F o r the F i rst T i me

Adapter Features

1-2

1-4

H a rdware/Software C o mpatibility

What the A d apter D o es

1-5

U s e of the C o mmon Industrial Protocol (C IP)

U n derstand the Producer /C o nsumer Model

Specify the R e quested P a cket Interval (R PI)

Support of R a ck-optimized and D i rect C o nnections

Mix R a ck-optimized and D i rect C o nnections

1-5

1-6

1-7

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

Before you begin using your adapter, note the following important

considerations.

Important Adapter

Considerations

Set the Chassis Size

The 1734-AENT POINT I/O adapter for EtherNet/IP requires

configuration of its chassis size before you can make any I/O

connections. The default setting for the chassis size is 1 slot, which

represents the adapter by itself.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1-2

About the Adapter

You must set the chassis size to a number equaling 1 slot for the

adapter plus 1 slot for each I/O module present in the adapter’s

backplane. For example, the adapter plus 4 I/O modules uses a

chassis size of 5. The adapter stores this chassis size setting in

non-volatile storage.

When the adapter’s non-volatile chassis size does not match the actual

number of modules present on its backplane, the adapter does not

make any I/O connections and an error occurs, as shown in the

Module Properties dialog.

Adapter Replacement

It is important to note that during a connection request from the

controller, the chassis size setting for a 1734-AENT adapter is not

communicated to the adapter. You must always set this chassis size

using a separate operation. This includes situations when you are

replacing an adapter. The adapter does not make any I/O connections

until it is configured with the appropriate chassis size.

Empty Slots and RIUP Situations

The POINT I/O system does not have the ability to detect an empty

terminal base. Because of this, there are numerous situations in which

you can potentially configure a system that is unusable or one that

exercises unintended control.

In an attempt to address these situations, you must observe the

following rules for POINT I/O system construction and the removal

and reinsertion of modules.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

About the Adapter

1-3

• A correct POINT I/O system does not have any empty terminal

bases.

• After you cycle power, the adapter will not run any I/O until the

number of modules comprising the chassis equals the stored

chassis size.

– Because the adapter cannot detect empty terminal bases, it

cannot assume any safe operation until there is a match

between the number of modules indicating their presence in

the chassis and what the adapter has saved in non-volatile

memory.

– Actual module identification (such as, electronic keying) is

done when connection establishment requests are received

from the controller or controllers.

• A module removed under power does not disrupt operation of

the other I/O modules.

– When you remove a module, the adapter determines what

changed.

– Whenever you remove a module with an active connection

from the POINT I/O system, the adapter indicates this by

flashing the POINTBus Status LED red and reports a minor

recoverable fault.

• If more than one contiguous module is removed under power,

connections to all modules in the contiguous missing module set

are disallowed until all modules are replaced. Because the

adapter cannot detect an empty base, it does not know the

physical positioning of the modules until all the missing

modules are replaced.

• If a module separating two sets of contiguous missing modules

is removed, the two sets merge into a single set. All the modules

must be replaced before connections are permitted to any

module in the set.

• If modules of different types are removed and returned to the

wrong locations, attempts to connect to these modules will fail

during verification of the electronic ID (providing that keying

has not been disabled).

• If modules of the same type are removed and returned to the

wrong locations, they accept connections from the controller or

controllers and reconfigure with the correct data once they pass

their electronic keying check.

• These removal and return situations exist whether the system is

under power or not. If the system is under power, the situation

arises immediately. If the system is not under power, the

situation arises in the next power cycle.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4

About the Adapter

Cycle Power To a System For the First Time

When you power POINT I/O for the first time, the adapter must assign

addresses to every module in the backplane. POINT I/O modules all

ship configured at the same address.

When you first apply power, we expect that all but one module on

the backplane exhibits a solid red Module Status LED.

One by one the adapter resets these modules and addresses them

appropriately. The amount of time that this operation takes is

proportional to the size of your POINT I/O system.

The 1734-AENT adapter’s features include:

Adapter Features

• EtherNet/IP messages encapsulated within standard

TCP/UDP/IP protocol

• Common application layer with ControlNet and DeviceNet

networks

• Interfacing via Category 5 rated twisted pair cable

• Half/full duplex 10 Mbit or 100 Mbit operation

• DIN rail mounting

• Communication to and from other POINT I/O modules on the

same DIN rail

• Communication supported by RSLinx software

• IP address assigned via standard BootP or DHCP tools

• I/O configuration via RSLogix 5000 software

• No network scheduling required

• No routing tables required

• Support of connections from multiple controllers simultaneously

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

About the Adapter

1-5

The 1734-AENT adapter and the applications described in this manual

are compatible with the following firmware revisions and software

releases. Contact Rockwell Automation if you need software or

firmware upgrades to use this equipment.

Hardware/Software

Compatibility

Product

Firmware Revision/

Software Release

1734-AENT adapter

1756-ENBT module

Logix 5555 controller

RSLogix 5000 software

RSLinx software

1.xx or later

2.3 or later

11 or later

11.11 or later

2.3.1 or later

The 1734-AENT adapter performs the following primary tasks:

What the Adapter Does

• Control of real-time I/O data (also known as implicit messaging)

- the 1734-AENT adapter serves as a bridge between POINT I/O

modules and the network

EtherNet/IP Network

Other

Network

Devices

POINT

I/O

ControlLogix

I/O

• Support of messaging data for configuration and programming

information (also known as explicit messaging)

The 1734-AENT adapter uses the Common Industrial Protocol (CIP).

CIP is the application layer protocol specified for EtherNet/IP, the

Ethernet Industrial Protocol, as well as for ControlNet and DeviceNet

networks. It is a message-based protocol that implements a relative

path to send a message from the producing device in a system to the

consuming devices.

Use of the Common

Industrial Protocol (CIP)

The producing device contains the path information that steers the

message along the proper route to reach its consumers. Since the

producing device holds this information, other devices along the path

simply pass this information; they do not need to store it.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1-6

About the Adapter

This has the following significant benefits.

• You do not need to configure routing tables in the bridging

modules, which greatly simplifies maintenance and module

replacement.

• You maintain full control over the route taken by each message,

which enables you to select alternative paths for the same end

device.

The CIP producer/consumer networking model replaces the old

source/destination (master/slave) model. The producer/consumer

model reduces network traffic and increases speed of transmission. In

traditional I/O systems, controllers poll input modules to obtain their

input status. In the CIP system, input modules are not polled by a

controller. Instead, they produce (multicast) their data either upon a

change of state (COS) or periodically.

Understand the

Producer/Consumer Model

The frequency of update depends upon the options chosen during

configuration and where on the network the input module resides.

The input module, therefore, is a producer of input data, and the

controller is a consumer of the data.

The controller can also produce data for other controllers to consume.

The produced and consumed data is accessible by multiple controllers

and other devices over the EtherNet/IP network. This data exchange

conforms to the producer/consumer model.

The RPI is the update rate specified for a particular piece of data on

the network. The RPI can be specified for the adapter and include all

of the I/O modules communicating through it (using a rack-optimized

connection) or specified for a particular module (using direct

connection).

Specify the Requested

Packet Interval (RPI)

When you add a module or an adapter to the I/O configuration of a

controller, you must enter the RPI as a parameter. This value specifies

how often to produce the data for that device. For example, if you

specify an RPI of 50 ms, it means that every 50 ms the device should

send its data to the controller or the controller should send its data to

the device.

Use RPIs only for devices that exchange data. For example, a

ControlLogix EtherNet/IP bridge module in the same chassis as the

controller does not require an RPI, because it is not a data-producing

member of the system. Its use is only as a bridge to remote racks.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

About the Adapter

1-7

The 1734-AENT adapter supports both direct and rack-optimized

connections. A direct connection is a real-time data transfer link

between the controller and whatever module occupies the slot that

Support of Rack-optimized

and Direct Connections

the configuration data references. Direct connection messaging occurs

at a cyclic rate specified by the RPI during configuration. A

rack-optimized connection is a grouping of data from more than one

I/O module into a single block of data sent over a single connection

at the same data rate.

Rack-optimized connections reduce the total number of connections

needed to transfer data when using many I/O modules in a system.

The following example illustrates the benefit of rack-optimized

connections.

Assume you set up a system that contains 8 digital I/O modules

interfaced to a 1734-AENT adapter. If you use direct connections to

transfer data to each of the these I/O modules, you need 8

connections to transfer all of the data, one to each of the 8 I/O

modules. If you use a rack-optimized connection to transfer the data,

you only need a single connection – the connection to the 1734-AENT

adapter.

Although rack-optimized connections offer an

efficient way to use resources, there are a few

limitations on their use:

IMPORTANT

• You can use only rack-optimized connections

to send data to and from digital I/O modules.

Analog or speciality I/O requires direct

connections.

• All data is sent at the same time as the RPI rate

of the 1734-AENT adapter.

See the EtherNet/IP Performance and Application Guide, publication

number ENET-AP001, for more information on connections.

Mix Rack-optimized and Direct Connections

You can mix communication formats for different I/O modules

communicating through the same adapter. I/O modules set up to use

rack optimization communicate at the rate of the RPI configured for

the 1734-AENT adapter. I/O modules configured for direct

communication communicate at their own set RPIs and ignore the

1734-AENT adapter’s RPI.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1-8

About the Adapter

To effectively use your adapter, note the following considerations.

Before You Begin

Determine Compatibility

If using the adapter with a 1756-ENBT module or 1788-ENBT module,

use the following required firmware revisions for these bridge

modules:

• 1756-ENBT firmware revision 2.3 or later

• 1788-ENBT firmware revision 1.33 or later

If you use the BootP Utility to assign IP addresses to the adapter, use

revision 2.3.2 or later.

Understand Messaging

Class 3 (Explicit Message) requests through the 1734-AENT adapter to

a specific POINT I/O module may not always receive a response from

the I/O modules. In the case where the I/O module does not reply to

the request, the adapter responds with an error code indicating a

timout.

Establish I/O Connections

When you apply power to a POINT I/O system and establish I/O

connections, the outputs transition to the Idle state, applying Idle state

data before going to RUN mode. This occurs even when the controller

making the connection is already in RUN mode.

Configure Autobaud

The adapter cannot reconfigure an I/O module that you previously

configured to operate at a fixed communication rate. When you reuse

a POINT I/O module from another POINT I/O system, configure the

module to autobaud before using it with the adapter.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter

Install the Adapter

This chapter describes how to physically install the adapter on the

DIN rail and connect it to the EtherNet/IP network. The following

table lists where to find specific information.

What This Chapter Contains

Topic

See Page

Identify A d apter C o mponents

Mount the A d apter on a D IN R a il B e fore Installing Modules

Mount (or R e place) the A d apter to an E xi s ting System

Wiring

Mounting D i mensions

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

Use the figure to identify the external features of the adapter.

Identify Adapter

Components

Safety End Cap

LED Indicators

Node Address

Thumbwheel

RTB

Removal Handle

Removable

Terminal

Block (RTB)

EtherNet

Network

RJ45

DIN Rail

Locking

Connector

Screw (orange)

31533-M

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

2-2

Install the Adapter

Use the following procedure to mount the adapter on a new system

before you install any I/O modules.

Mount the Adapter on a DIN

Rail Before Installing

Modules

43520

1. Position the adapter vertically above the DIN rail.

2. Press down firmly to install the adapter on the DIN rail, noting

that the locking mechanism locks the adapter to the DIN rail.

3. Set the network address thumbwheel switches to the desired

value (see Set the Network Address section in this manual).

If you connect or disconnect the Ethernet cable with

WARNING

power applied to this module or any device on the

network, an electrical arc can occur. This could

cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is

nonhazardous before proceeding.

4. Slide the safety end cap up to remove it.

This exposes the backplane and power interconnections.

Do not discard the adapter’s end cap. Use this end

ATTENTION

cap to cover the exposed interconnections on the

last mounting base on the DIN rail. Failure to do

so could result in equipment damage or injury

from electric shock.

Publication 1734-UM011C-EN-P - December 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Install the Adapter

2-3

Follow these steps to mount (or replace) an adapter.

Mount (or Replace) the

Adapter to an Existing

System

1. Remove the existing adapter (if there is one) from the DIN rail

as follows:

a. Pull up on the RTB removal handle to remove the terminal

block.

b. Disconnect the Ethernet connector from the adapter.

c. Remove the adjacent module from its base.

d. Use a small-bladed screwdriver to rotate the DIN-RAIL locking

screw to a vertical position.

This releases the locking mechanism.

e. Lift straight up to remove.

2. For the replacement adapter, slide the safety end cap up to

remove.

This exposes the backplane and power connections.

3. Position the replacement adapter vertically above the DIN rail.

4. Make certain the DIN rail lock is in the horizontal position.

5. Slide the adapter down, allowing the interlocking side pieces to

engage the adjacent module.

6. Press firmly to seat the adapter on the DIN rail.

The adapter locking mechanism snaps into place.

7. Replace the adjacent module in its base.

8. Reconnect the Ethernet cable to the adapter.

9. Set the network address thumbwheel switches to the value used

on the replaced module (see Set the Network Address in this

manual).

10. Insert the end of the terminal block (RTB) opposite the handle

into the base unit.

This end has a curved section that engages with the wiring base.

11. Rotate the terminal block into the wiring base until it locks itself

into place.

Publication 1734-UM011C-EN-P - December 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

2-4

Install the Adapter

Refer to the illustration to wire the adapter.

If you connect or disconnect wiring while

Wiring

WARNING

the field-side power is on, an electrical arc

can occur. This could cause an explosion

in hazardous location installations.

Be sure that power is removed or the area

is nonhazardous before proceeding.

Module Status

Network Address

Thumbwheels

Network Activity Status

Network Status

P O I N T B u s S t a t u s

Ethernet RJ-45 Connector

System Power

Field Power

CHAS GND

NC = No Connection

CHAS GND = Chassis Ground

C = Common

43264

V = Supply

12/24V dc

Do not connect

120/240V ac power to

this supply.

ATTENTION

Chas Chas

Gnd Gnd

This dc supply will be

connected to the

internal power bus.

V dc

NC = No Connection

Chas GND = Chassis Ground

C = Common

V = Supply

Publication 1734-UM011C-EN-P - December 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Install the Adapter

2-5

Refer to the figure for mounting dimensions.

Mounting Dimensions

millimeters

(inches)

54.9

(2.16)

76.5

(3.0)

133.4

(5.25)

36.51

(1.44)

43520

1734-AENT

76.2H x 54.9W x 133.4D

(3.0H x 2.16W x 5.25D)

A = DIN rail

B = Secure DIN rail approximately every 200 mm (7.8 in.)

Publication 1734-UM011C-EN-P - December 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

2-6

Install the Adapter

Notes:

Publication 1734-UM011C-EN-P - December 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter

Configure the Adapter for Your EtherNet/IP

Network

Before using your adapter in an EtherNet/IP network, configure it

What This Chapter Contains

with an IP address, subnet mask, and optional Gateway address. This

chapter describes these configuration requirements and the

procedures for providing them. Here are ways you can do this:

• Use the Rockwell BootP utility, version 2.3 or later, that ships

with RSLogix 5000 or RSLinx software.

– You can also use this utility to reconfigure a device with an IP

address you must change.

• Use a third party DHCP server.

• Use the Network Address thumbwheel switch.

• Have your network administrator configure the adapter via the

network server.

See the table for a list of where to find information in this chapter.

For Information About

C o nfiguration R e quirements

See Page

Set the Network A d dress

U s e the R o ckwell B o otP /D HCP U t ility

Save the R e lation L i st

U s e D HCP S oftware to C o nfigure Y o ur A d apter

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

3-2

Configure the Adapter for Your EtherNet/IP Network

Before you can use your adapter, you must configure its IP address,

its subnet mask, and, optionally, gateway address. You can use the

Rockwell BootP utility, version 2.3 or later, to perform the

configuration. You can also use a DHCP server or the network

address switches to configure these parameters.

Configuration

Requirements

If you need to reset the adapter to factory defaults, see the Important

note about setting thumbwheels to the value 888.

IP Address

Ethernet Address (MAC)

If you set the thumbwheels on the adapter to the

value 888 and then power cycle the module, the

following will occur.

IMPORTANT

• The DHCP Enabled function is enabled (set to

True).

• The Ethernet link is negotiated automatically

(the Auto Negotiate function will be set to

True).

• The web server is enabled (the Disabled Web

Server function is disabled).

• The password for this page resets to the

factory default (the word password is the

factory default password).

Note the value of the switches before you enter

the 888 value, because you return the adapter to

those values once this process is complete.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Your EtherNet/IP Network

3-3

If using the BootP/DHCP utility, you need to

know the Ethernet hardware address of your

adapter. Rockwell assigns each 1734-AENT

IMPORTANT

adapter a unique 48-bit hardware address at the

factory. The address is printed on a label on the

side of your 1734-AENT adapter as shown in the

figure. It consists of six hexadecimal digits

separated by colons. This address is fixed by the

hardware and cannot be changed.

Ifyou change orreplace the 1734-AENTadapter,you

mustenterthe new Ethernethardware addressofthe

adapter when you configure the new adapter.

IP Address

The IP address identifies each node on the IP network (or system of

connected networks). Each TCP/IP node on a network (including the

1734-AENT adapter) must have a unique IP address.

The IP address is 32 bits long and has a net ID part and Host ID part.

Networks are classified A, B, C, (or other). The class of the network

determines how an IP address is formatted.

7 8

Host ID

Class A

Class B

Net ID

Host ID

Net ID

1 0

Class C

Net ID

1 1 0

Host ID

You can distinguish the class of the IP address from the first integer in

its dotted-decimal IP address as follows:

Range of first integer

0 …127

Class

Range of first integer

192 … 223

Class

128 …191

224 … 255

other

Each node on the same physical network must have an IP address of

the same class and must have the same net ID. Each node on the

same network must have a different Host ID thus giving it a unique IP

address.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

3-4

Configure the Adapter for Your EtherNet/IP Network

IP addresses are written as four decimal integers (0 to 255) separated

by periods where each integer gives the value of one byte of the IP

address.

For example, the 32-bit IP address:

EXAMPLE

10000000 00000001 00000000 00000001 is written as

128.1.0.1

Gateway Address

This section applies to multi-network systems. If you have a single

network system, refer to the next section.

The Gateway Address is the default address of a network. It provides

a single domain name and point of entry to the site. Gateways

connect individual physical networks into a system of networks.

When a node needs to communicate with a node on another network,

a gateway transfers the data between the two networks. The figure

shows gateway G connecting Network 1 with Network 2.

128.1.0.1

Network 1

128.1.0.2

128.2.0.3

128.2.0.1

128.2.0.2

Network 2

When host B with IP address 128.2.0.1 communicates with host C, it

knows from C’s IP address that C is on the same network. In an

Ethernet environment, B can then resolve C’s IP address into a

hardware address (MAC address) and communicate with C directly.

When host B communicates with host A, it knows from A’s IP address

that A is on another network (the net IDs are different). In order to

send data to A, B must have the IP address of the gateway connecting

the two networks. In this example, the gateway’s IP address on

Network 2 is 128.2.0.3.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Your EtherNet/IP Network

3-5

The gateway has two IP addresses (128.1.0.2 and 128.2.0.3). The first

must be used by hosts on Network 1 and the second must be used by

hosts on Network 2. To be usable, a host’s gateway must be

addressed using a net ID matching its own.

Subnet Mask

The subnet mask is used for splitting IP networks into a series of

subgroups, or subnets. The mask is a binary pattern that is matched

up with the IP address to turn part of the Host ID address field into a

field for subnets.

Take Network 2 (a Class B network) in the

EXAMPLE

previous example and add another physical

network. Selecting the following subnet mask

would add two additional net ID bits, allowing

for four physical networks:

11111111 11111111 11000000 00000000 =

255.255.192.0

These two bits of the Host ID are used to

extend the net ID.

Two bits of the Class B host ID are used to extend the net ID. Each

unique combination of bits in the part of the Host ID where subnet

mask bits are 1 specifies a different physical network.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

3-6

Configure the Adapter for Your EtherNet/IP Network

The new configuration is:

128.1.0.1

Network 1

128.1.0.2

128.2.64.3

128.2.64.1

128.2.64.2

Network 2.1

128.2.128.3

128.2.128.1

128.2.128.2

Network 2.2

A second network with Hosts D and E was added. Gateway G2

connects Network 2.1 with Network 2.2.

Hosts D and E will use Gateway G2 to communicate with hosts not on

Network 2.2.

Hosts B and C will use Gateway G to communicate with hosts not on

Network 2.1.

When B is communicating with D, G (the configured Gateway for B)

will route the data from B to D through G2.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Your EtherNet/IP Network

3-7

The adapter ships with the thumbwheel switches set to 999 and DHCP

enabled. You can set the network Internet Protocol (IP) address in

these ways:

Set the Network Address

• Use the thumbwheel switches located on the module.

• Use a Dynamic Host Configuration Protocol (DHCP) server, such

as Rockwell Automation BootP/DHCP.

• Retrieve the IP address from nonvolatile memory.

Network Address

Thumbwheel

Press either the + or -

buttons to change the

number.

43248

The adapter reads the thumbwheel switches only when you cycle

power to determine if the switches are set to a valid number. Press

either the + or - buttons to change the number.

Valid settings range from 001 to 254. When the switches are set to a

valid number, the adapter’s IP address will be 192.168.1.xxx (where

xxx represents the number set on the switches). The adapter’s subnet

mask will be 255.255.255.0 and the gateway address is set to 0.0.0.0.

The adapter will not have a host name assigned, or use any Domain

Name System when using the thumbwheel settings.

If the switches are set to an invalid number (such as 000 or a value

greater than 254), the adapter checks to see if DHCP is enabled. If

DHCP is enabled, the adapter requests an address from a DHCP

server. The DHCP server will also assign other Transport Control

Protocol (TCP) parameters.

If DHCP is not enabled, the adapter will use the IP address (along

with other TCP configurable parameters) stored in nonvolatile

memory. The factory default switch setting is 999, and DHCP is

enabled.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

3-8

Configure the Adapter for Your EtherNet/IP Network

The Rockwell BootP/DHCP utility is a stand alone program that

incorporates the functionality of standard BootP software with a user

friendly graphical interface. It is located in the Utils directory on the

RSLogix5000 installation CD. The 1734-AENT adapter must have

DHCP enabled (factory default and the network address switches set

to an illegal value) to use the utility.

Use the Rockwell

BootP/DHCP Utility

To configure your adapter using the BootP utility, perform the

following steps:

1. Run the BootP software.

In the BOOTP Request History panel you see the hardware

addresses of devices issuing BootP requests.

2. Double-click the hardware address of the device you want to

configure.

You see the New Entry dialog with the device’s Ethernet

Address (MAC).

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Your EtherNet/IP Network

3-9

3. Enter the IP Address you want to assign to the device, and click

OK.

The device is added to the Relation List, displaying the Ethernet

Address (MAC) and corresponding IP Address, Hostname, and

Description (if applicable).

When the address displays in the IP Address column in the

Request History section, it signifies that the IP address

assignment has been made.

4. To assign this configuration to the device, highlight the device in

the Relation List panel, and click the Disable BOOTP/DHCP

button.

When power is cycled to the device, it uses the configuration

you assigned and not issue a DHCP request.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

3-10

Configure the Adapter for Your EtherNet/IP Network

5. To enable DHCP for a device with DHCP disabled, highlight the

device in the Relation List, and click the Enable DHCP button.

You must have an entry for the device in the Relation List panel

to re-enable DHCP.

Save the Relation List

You can save the Relation List to use later. To save the Relation List

perform the following steps:

1. Select Save As... from the File menu.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Your EtherNet/IP Network

3-11

You see the Save As dialog.

2. Select the folder you want to Save in.

3. Enter a File name for the Relation List (for example, control

system configuration), and clickclick Save.

You can leave the Save as type at the default setting: Bootp

Config Files (*.bpc).

You can then open the file containing the Relation List at a later

session.

DHCP (Dynamic Host Configuration Protocol) software automatically

assigns IP addresses to client stations logging onto a TCP/IP network.

Use DHCP Software to

Configure Your Adapter

DHCP is based on BootP and maintains some backward compatibility.

The main difference is that BootP was designed for manual

configuration, while DHCP allows for dynamic allocation of network

addresses and configurations to newly attached devices.

Be cautious about using DHCP software to configure your adapter. A

DHCP server typically assigns a finite lease time to the offered IP

address.

When 50% of the leased time has expired, the 1734-AENT adapter

attempts to renew its IP address with the DHCP server.

The possibility exists that the adapter will be assigned a different IP

address, which would cause the adapter to cease communicating with

the ControlLogix controller.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

3-12

Configure the Adapter for Your EtherNet/IP Network

Refer to the section Configure the 1734-AENT Adapter with Fixed IP

Address in this manual to configure the adapter with a fixed IP

address.

To avoid unintended control, the 1734-AENT adapter

ATTENTION

must be assigned a fixed IP address. The IP address

of this adapter should not be dynamically provided.

If a DHCP server is used, it must be configured to

assign a fixed IP address for your adapter.

Failure to observe this precaution may result in

unintended machine motion or loss of process

control.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter

Configure the Adapter for Direct Connection

in RSLogix 5000 Software

In this example, a ControlLogix controller communicates with POINT

I/O modules via the 1734-AENT adapter using a direct connection.

What This Chapter Contains

The adapter makes a direct connection to each of the modules

referenced by the data. The modules presented in this chapter use

RSLogix 5000 software, version 11.

What You Do

See Page

4-1

Set U p t he H a rdware

C r eate the E x a m ple A p plication

C o nfigure the I /O

4-2

4-4

A d d the L o cal E t herNet/IP B r idge to the I /O C o nfiguration

A d d the P O INT I /O A d apter to the I/O C o nfiguration

A d d the P O INT I /O M odules to the I /O C o nfiguration

A d d the R e lay O u tput Module

A d d the D i gital O u tput Module

E d it the C o ntroller T a gs

C r eate the L a dder Program

D o wnload the Program to the C o ntroller

V e rify the Module C h assis Size

C o nfigure the A d apter with F i xed IP A d dress

R e cover F r om an O v e rloaded A d apter

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

In this example, a ControlLogix chassis contains the Logix5555

processor in slot 1 and a 1756-ENBT bridge module in slot 3.

Set Up the Hardware

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-2

Configure the Adapter for Direct Connection in RSLogix 5000 Software

We mounted the 1734-AENT adapter on a DIN rail in slot 0, with a

1734-OW2/C relay output module in slot 1, a 1734-OV4E/C sink

output module in slot 2, and a power supply (not shown).

1734-AENT

10.88.70.2

POINT I/O

Slot 0 1 2 3

Local

Chassis

Data

1756-ENBT

10.88.70.4 (slot 3)

Slot 0 1 2 3 4

Logix5555

Controller (slot 1)

Switch

10.88.70.26

Programming

Terminal

31393-M

To work along with this example, set up your system as shown in the

figure.

• In the example application, we assume that the Logix5555

controller and 1756-ENBT module (firmware revision 2.3, or

later) are in the slots shown in the figure.

• Verify the IP addresses for your programming terminal,

1756-ENBT module, and 1734-AENT adapter.

• Verify the position (slot) of the I/O modules on the DIN rail.

• Verify that you connected all wiring and cabling properly.

• Be sure you configured your communication driver (for

example, AB_ETH-1 or AB-ETHIP-1) in RSLinx software, as

described in the Configure the RSLinx Ethernet Communication

Driver appendix of this manual.

Perform the following steps to create the example application:

Create the Example

Application

1. Start RSLogix 5000 Enterprise Series software to open the

RSLogix 5000 Main dialog.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-3

2. From the File menu, select New.

The New Controller dialog opens.

3. Enter an appropriate Name for the Controller, for example,

POINT_IO_Controller.

4. Select the correct Version, Chassis Type, and Slot number of the

Logix5555 controller, and the folder where you want to save the

RSLogix 5000 file (Create In). The Description is optional.

RSLogix 5000 software version 11 or later lets you choose to

enable redundancy. This example does not use redundancy. To

use redundancy in your system, check the Redundancy Enabled

checkbox so that a checkmark appears.

5. Click OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-4

Configure the Adapter for Direct Connection in RSLogix 5000 Software

You now add the POINT I/O modules to the controller’s I/O

configuration performing these procedures.

Configure the I/O

• Add the local 1756-ENBT module to the I/O configuration.

• Add the 1734-AENT adapter as a child of the 1756-ENBT

module.

• Add the I/O modules as children of the 1734-AENT adapter.

Click the Help buttons on the configuration

dialogs shown in this section if you need

IMPORTANT

assistance in selecting and setting the parameters.

Add the Local EtherNet/IP Bridge to the I/O Configuration

1. Select the I/O Configuration folder in the project dialog, and

click the right mouse button.

A dialog opens.

2. Click New Module.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-5

The Select Module dialog opens.

3. Click + next to Communications to expand, as in the following

dialog.

4. Select the 1756-ENBT EtherNet/IP Bridge, and click OK.

The Select Major Revision dialog opens.

5. Select the number for Major Revision, and click OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-6

Configure the Adapter for Direct Connection in RSLogix 5000 Software

The New Module dialog opens.

6. Enter values for Name, IP Address, Slot, Electronic Keying, and

Revision, noting that we used the following values:

Name

Local_ENB

IP Address

Slot

10.88.70.4

Electronic Keying

Revision

Compatible Keying

3.1

7. Click OK to accept the configuration.

The Module Properties dialog opens.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-7

Add the POINT I/O Adapter to the I/O Configuration

Next, you must add the 1734-AENT adapter as a child of the local

1756-ENBT module.

1. In the Project dialog, right-click the local 1756-ENBT module

under the I/O Configuration folder, and select New Module from

the dialog.

The Select Module dialog opens.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-8

Configure the Adapter for Direct Connection in RSLogix 5000 Software

2. Click + next to Communications to expand.

3. Select the 1734-AENT/A Ethernet adapter from the list, and click

OK, noting that we used these values.

Name

POINT_IO_Adapter

IP Address

Comm Format

Chassis Size

Electronic Keying

Revision

10.88.70.2

None

Compatible Keying

1.1

The Slot field appears grey because the slot is automatically 0 for the

1734-AENT adapter.

The chassis size equals 1 for the adapter plus the

number of POINT I/O modules installed (physically

present on the POINT I/O backplane).

IMPORTANT

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-9

The New Module dialog opens.

Comm Format choices are the following.

• None = the adapter makes a direct connection to each of the

modules referenced by the data.

• Rack optimization = digital I/O data is collected into a rack

image. This does not include analog or specialty I/O

modules.

• Listen only - rack optimization = read or verify data only, but

does not control the modules (when you have multiple

controllers - one controller is used to control and the other

controllers are used to monitor).

4. Choose None as Comm Format, because we are making a direct

connection, and click OK.

Because you entered None as the Comm Format, the requested

packet interval (RPI) is disabled.

The 1734-AENT adapter appears in the Ethernet folder.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-10

Configure the Adapter for Direct Connection in RSLogix 5000 Software

Add the POINT I/O Modules to the I/O Configuration

You now add POINT I/O modules to the I/O Configuration List under

the 1734-AENT adapter.

In this example, you add a 1734-OW2 relay output and a 1734-OV4E

sink output module with standard configurations. Use these steps as a

guide when configuring different I/O modules for your system.

This example application uses the I/O modules

TIP

default configurations. For more information, see the

POINT I/O Selection Guide, publication no.

1734-SG001.

Add the Relay Output Module

1. Right-click the remote 1734-AENT adapter under the I/O

Configuration folder and select New Module.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-11

The Select Module dialog opens.

2. Click the + next to Digital to expand.

3. Select the 1734-OW2 relay output module from the list, and click

OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-12

Configure the Adapter for Direct Connection in RSLogix 5000 Software

The New Module dialog opens.

4. Enter values for Name and Slot, noting that we used the

following values.

Name

Slot

POINT_Relay_Output

5. Choose Connection.

The RPI is selectable since it is a direct connection.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-13

6. Enter 50 for requested packet interval (RPI) to set how often you

exchange data with the 1734-AENT adapter.

To avoid overloading the 1734-AENT adapter, we

IMPORTANT

recommend that RPI be no less than 10 ms for

rack connections and 50 ms for direct

connections.

7. Click OK save the configuration.

The relay output module appears under Ethernet.

Add the Digital Output Module

1. Right-click the 1734-AENT adapter, and select New Module.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-14

Configure the Adapter for Direct Connection in RSLogix 5000 Software

The Select Module dialog opens.

2. Click + next to Digital to expand.

3. Select the 1734-OV4E digital output module from the list.

4. Click OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-15

The New Module dialog opens.

5. Enter values for Name and Slot, noting we used the following.

Name

Slot

POINT_Digital_Output

6. Click Connection at the top of the screen.

7. Enter 10 ms as the RPI for the 1734-OV4E module.

8. Click OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-16

Configure the Adapter for Direct Connection in RSLogix 5000 Software

The I/O Configuration in the Project dialog should look similar

to the following.

When you add modules to the I/O configuration the system creates

tags for those modules to use in the application program.

Edit the Controller Tags

For the example application you need to add one more controller

tags.

1. Double-click the Controller Tags folder in the project dialog.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-17

The Controller Tags dialog opens. You see the tags created for

the 1734-AENT adapter and digital I/O modules.

Tags created by the

system

Enter the new tag here

2. Click the Edit Tags tab at the bottom of the Controller Tags

dialog.

3. Create the following tag :

Tag

Type

Parts_Count

Counter

4. Close the Controller Tags dialog.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-18

Configure the Adapter for Direct Connection in RSLogix 5000 Software

Next create the example ladder program to test the I/O.

Create the Ladder Program

1. Double-click Main Routine under the Main Program folder.

2. Enter the following ladder program using the tags previously

created.

3. Save the program.

Follow this procedure to download the program you just saved to the

ControlLogix controller.

Download the Program to

the Controller

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-19

1. From the main menu, choose Communications>Who-Active.

You see the Who Active dialog.

2. Navigate to select the slot where the controller is located in the

chassis.

3. Choose Set Project Path.

4. Choose Download.

You see the Download dialog with a reminder of the following.

• The controller is in Remote Run mode.

• The mode changes to Remote Program prior to download.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-20

Configure the Adapter for Direct Connection in RSLogix 5000 Software

5. From the Download dialog, choose Download to see the

RSLogix5000 software dialog.

6. Notice that the 1756-ENBT Bridge is now online.

If yellow triangles are present, see the following section.

You have now built the I/O tree in RSLogix 5000 software, and the

RSLogix 5000 software used the chassis size from the 1734-AENT

General tab.

Verify the Module Chassis

Size

Now you need to download this new chassis size value into the

1734-AENT adapter hardware. This procedure synchronizes the

chassis size value from the RSLogix 5000 software into the 1734-AENT

adapter hardware.

1. Verify that RSLogix 5000 is online.

2. Right-click the 1734-AENT adapter under I/O Configuration in

the Project dialog.

3. Select Properties.

4. Click the Connection tab.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-21

You see the Module Fault error code.

5. Click the Chassis Size tab.

6. Click Set Chassis Size in Module.

Value from

RSLogix 5000

software

Value stored

in 1734-AENT

adapter

7. Read and acknowledge the warning dialog.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-22

Configure the Adapter for Direct Connection in RSLogix 5000 Software

8. Click OK to continue.

Notice the chassis size in the module is modified to 3.

9. Click OK.

At this point, your POINTBus status LED should be solid green.

All the yellow triangles in your I/O configuration should be

gone.

To configure the 1734-AENT adapter with a fixed IP address to

prevent the adapter from ceasing to communicate with the

ControlLogix controller:

Configure the Adapter with

Fixed IP Address

1. Click the Port Configuration tab in the 1734-AENT adapter

properties dialog.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection in RSLogix 5000 Software

4-23

2. Click the Enable DHCP box so that there is not a checkmark in

the box.

3. Click the Set button.

4. Read and acknowledge the warning.

5. Click OK.

6. Click the Refresh button to verify the changes.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

4-24

Configure the Adapter for Direct Connection in RSLogix 5000 Software

Each POINT I/O connection established with the 1734-AENT adapter

consumes a portion of the microprocessor’s bandwidth. The amount

of bandwidth used by a connection depends on a number of

variables, including the requested packet interval (RPI), the number of

POINT I/O modules involved in the connection, and the rate of

change of the I/O.

Recover From an

Overloaded Adapter

The 1734-AENT adapter continuously monitors this bandwidth and

rejects requests for new connections when there is insufficient

bandwidth available to support the new connection.

The condition where the 1734-AENT adapter cannot support the

connection due to a limit of the microprocessor’s bandwidth is shown

in the following dialog.

If you encounter this condition, the only action you can take is to alter

the existing connections to reduce the amount of microprocessor

bandwidth consumed. The most likely fixes for this condition include

the following.

• Increase the RPI.

• Decrease the number of connections.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter

Configure the Adapter for Direct Connection

and Rack Optimization in RSLogix 5000

Software

This chapter guides you through the steps required to configure your

1734 POINT I/O Ethernet adapter for both direct connection and rack

optimization using RSLogix 5000 software.

What This Chapter Contains

You can mix communication formats for different I/O modules

communicating through the same adapter. I/O modules set up to use

rack optimization communicate at the rate of the RPI configured for

the 1734-AENT adapter.

I/O modules configured for direct communication communicate at

their own set RPI and ignore the 1734-AENT adapter RPI. The

modules presented in this chapter have a configuration using RSLogix

5000 software, version 15. The chapter contains the following main

sections:

What You Do

See Page

5-2

Set U p t he H a rdware

C r eate the E x a m ple A p plication

C o nfigure the I /O M odules

5-3

5-4

A d d the L o cal E t herNet/IP B r idge to the I /O C o nfiguration

A d d the P O INT I /O A d apter to the I/O C o nfiguration

5-4

5-7

A d d the P O INT I /O M odule and C o nfigure for D i rection

C o nnection

5-11

A d d the P O INT I /O M odule and C o nfigure F o r R a ck O p timization

D o wnload the Program to the C o ntroller

V e rify the Module C h assis Size

A c cess Module D a ta

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-2

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

In this example, a ControlLogix chassis contains the Logix 5555

controller in slot 1 and a 1756-ENBT bridge module in slot 3. We

mounted the 1734-AENT adapter on a DIN rail in slot 0, with a

1734-OW2/C relay output module in slot 1, a 1734-OV4E/C sink

output module in slot 2, and a power supply (not shown).

Set Up the Hardware

1734-AENT

10.88.70.2

POINT I/O

Slot 0 1 2 3

Local

Chassis

Data

1756-ENBT

10.88.70.4 (slot 3)

Slot 0 1 2 3 4

Logix5555

Controller (slot 1)

Switch

10.88.70.26

Programming

Terminal

31393-M

To work along with this example, set up your system as shown in the

figure.

• Note that in the example application, the Logix5555 controller

and 1756-ENBT module (firmware revision 2.3 or later) we

assume are in the slots shown in the figure.

• Verify the IP addresses for your programming terminal,

1756-ENBT module, and 1734-AENT adapter.

• Verify the position (slot) of the I/O modules on the DIN rail.

• Verify that you properly connected all wiring and cabling.

• Be sure you configured your communication driver (such as

AB_ETH-1 or AB-ETHIP-1) in RSLinx software as described in

the Configure the RSLinx Ethernet Communication Driver

appendix of this manual.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-3

Perform the following steps to create the example application:

1. Start RSLogix 5000 Enterprise Series software.

You see the RSLogix 5000 main dialog.

Create the Example

Application

2. From the File menu, select New.

The New Controller dialog opens

3. Enter an appropriate Name for the Controller, for example,

POINT_IO_Controller.

4. Select the following.

• Revision

• Chassis Type

• Slot number

• Description (optional)

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-4

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5. Complete the Create In entry by selecting the folder where you

want to save the RSLogix 5000 file.

6. To use redundancy in your system, check the Redundancy

Enabled checkbox so that a checkmark appears.

RSLogix 5000 software, version 11 and later, includes enable

redundancy. This example does not use redundancy.

7. Click OK.

You now add the POINT I/O modules to the controller I/O

configuration. To do this, first add the local 1756-ENBT module to the

I/O configuration. Next add the 1734-AENT adapter as a child of the

1756-ENBT module. Then add the I/O modules as children of the

1734-AENT adapter.

Configure the I/O Modules

Click the Help buttons on the configuration dialog

shown in this section if you need assistance in

selecting and setting the parameters.

IMPORTANT

Add the Local EtherNet/IP Bridge to the I/O Configuration

1. Select the I/O Configuration folder in the project dialog, and

click the right mouse button.

A dialog opens.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-5

2. Click New Module.

The Select Module dialog opens.

3. Click + next to Communications to expand, as in the following

dialog.

4. Select the 1756-ENBT EtherNet/IP Bridge, and click OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-6

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

The Select Major Revision dialog opens.

5. Select the value for Major Revision, and click OK.

The Module Properties dialog opens.

6. Enter value for Name, IP Address, Slot, Electronic Keying, and

Revision, noting we used the following values:

Name

Local_ENB

IP Address

Slot

10.88.70.4

Electronic Keying

Revision

Compatible Module

1.1

7. Click Finish to accept the configuration.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-7

Add the POINT I/O Adapter to the I/O Configuration

Next, you must add the 1734-AENT adapter as a child of the local

1756-ENBT module.

1. In the Project dialog, right-click the local 1756-ENBT module

under the I/O Configuration folder, and select New Module from

the dialog.

The Select Module dialog opens.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-8

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

2. Click + next to Communications to expand.

3. Select the 1734-AENT/A Ethernet adapter from the list, and click

OK.

The New Module dialog opens.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-9

4. Enter values for Name, IP Address, Comm Format, Chassis Size,

Electronic Keying, and Revision, noting we used the following

values.

Name

POINT_IO_Adapter

10.88.70.2

IP Address

Comm Format

Chassis Size

Electronic Keying

Revision

Rack Optimization

Compatible Keying

1.1

The Slot field appears grey because the slot is automatically

0 for the 1734-AENT adapter.

The chassis size equals 1 for the adapter plus the

number of POINT I/O modules installed (physically

present on the POINT I/O backplane).

IMPORTANT

Comm Format choices include:

• None = the adapter makes a direct connection to each of the

modules referenced by the data.

• Rack optimization = digital I/O data is collected into a rack

image. This does not include analog or specialty I/O modules.

• Listen only - rack optimization = read or verify data only, but

does not control the modules (when you have multiple

controllers - one controller is used to control and the other

controllers are used to monitor).

5. Choose Rack Optimization as Comm Format, because we are

making a mixed connection that includes both a direct

connection and rack-optimized connection.

6. Click OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-10

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

The Module Properties dialog opens.

7. Verify that the requested packet interval (RPI) is appropriate for

your system.

You use this value for the rack-optimized connection to the I/O

modules.

To avoid overloading the 1734-AENT adapter, we

recommend that you set RPI no less than 10 ms for

rack connections and 50 ms for direct connections.

IMPORTANT

8. Click OK.

The 1734-AENT adapter appears in the Ethernet folder.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-11

Add the POINT I/O Module and Configure for Direction

Connection

1. Highlight the 1734-AENT adapter under the I/O Configuration

folder, and select New Module.

The Select Module dialog opens.

2. Click + next to Digital to expand.

3. Select the 1734-OW2 relay output module from the list, and click

OK.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-12

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

The New Module dialog opens.

4. Enter values for Name and Slot,noting we used the following

values.

Name

Slot

POINT_Relay_Output

5. Choose Connection.

The RPI is selectable, since it is a direct connection.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-13

6. Verify that the requested packet interval (RPI) is appropriate for

your system (10 ms for this example). You use this value for the

rack-optimized connection to the I/O modules.

To avoid overloading the 1734-AENT adapter, we

recommend that the RPI be no less than 10 ms for

rack connections and 50 ms for direct connections.

IMPORTANT

7. Click OK to accept the configuration.

The 1734-AENT adapter appears indented under the local

1734-ENBT in the I/O Configuration folder.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-14

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

Add the POINT I/O Module and Configure For Rack Optimization

1. Right-click the 1734-AENT adapter under the I/O Configuration

folder, and select New Module.

If you exceed the 1734-AENT chassis size, trying to

IMPORTANT

add more modules than you configured, the New

Module selection appears dim and is disabled.

Increase the 1734-AENT chassis size to add more

POINT I/O modules.

The Select Module dialog opens.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-15

2. Click the + next to Digital to expand.

3. Choose the 1734-OV4E/C module, and click OK.

The New Module dialog opens.

4. From the New Module dialog, complete the following.

• Enter a value for Name.

• Enter a value for Slot.

• Click Change.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-16

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

You see the Module Definition screen.

5. From the Module Definition dialog, for Connection, select Rack

Optimization.

6. From the Module Definition dialog, click OK.

You see the New Module dialog.

7. From the New Module dialog, click Connection.

You see this New Module dialog.

8. From the New Module dialog, enter 50 for the requested packet

interval (RPI).

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-17

9. Keep the following unchecked.

• Inhibit Module

• Major Fault on Controller If Connection fails While in Run Mode

10. Click OK.

11. Choose File>Save and enter the name and location of the

RSLogix 5000 file.

Follow this procedure to download the program we just saved to the

ControlLogix controller.

Download the Program to

the Controller

1. From the main menu, choose Communications>Who-Active.

2. From the Who Active dialog, navigate to select the slot where

the controller is located in the chassis.

3. Choose Set Project Path.

4. Choose Download.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-18

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

You see the Download dialog.

5. From the Download dialog, click Download.

You see this RSLogix 5000 dialog.

6. Notice that the 1756-ENBT Bridge is now online.

7. If yellow triangles are present, see the following section.

You have now built the I/O tree in RSLogix 5000, and the RSLogix

5000 software used the chassis size from the 1734-AENT General tab.

Now you need to download this new chassis size value into the

1734-AENT adapter hardware. This procedure synchronizes the

chassis size value from the RSLogix 5000 software into the 1734-AENT

hardware. You must be online to perform this procedure.

Verify the Module

Chassis Size

1. Verify that RSLogix 5000 software is online.

2. Right-click the 1734-AENT adapter under I/O Configuration in

the Project dialog.

3. Select Properties.

4. Click the Connection tab.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-19

You see the Module Fault error code.

5. Click the Chassis Size tab.

6. Click Set Chassis Size in Module.

Value from

RSLogix 5000

software

Value stored

in 1734-AENT

adapter

7. Read and acknowledge the warning dialog.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-20

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

8. Click OK to continue.

9. Notice the chassis size in the module is modified to 3.

10. Click OK.

At this point, your POINTBus status LED should be solid green.

All the yellow triangles in your I/O configuration should be

gone.

11. Click OK to close the dialog.

12. Click File>Save to save the project.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

5-21

Use the following information to use the 1734 POINT I/O Ethernet

adapter data in the ladder logic program.

Access Module Data

• POINT_IO_Adapter = the name you gave to your Ethernet

adapter

• # = slot number of POINT I/O module

• C = configuration, I = input, O = output

This value indicates that slot 2 is

the only module participating in

the rack-optimized connection

with no errors.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

5-22

Configure the Adapter for Direct Connection and Rack Optimization in RSLogix 5000 Software

Use the controller tags in your ladder program to read input data or

write output data.

• For RSLogix 5000 programming instructions, refer to RSLogix

5000 Getting Results, publication 9399-RLD300GR.

• For ControlLogix controller information, refer to ControlLogix

System User Manual, publication 1756-UM001.

• Slot Status Bits: The Slot Status bits display the connection status

for each of the POINT I/O modules that use a rack-optimized

connection.

– Bit 0 is reserved for the adapter and always reports a value of

– Each of the other bits (1 to 63) correspond to a POINT I/O

module that you install in the POINT I/O backplane.

– In this example, we configured the 1734-AENT adapter for

both rack-optimized and direct connections.

The slot status bits indicate that we installed the module in

slot 2 with it operating correctly:

• 0=module participating with no errors and

• 1=module not participating or connection error (typically,

module removed/missing)

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter

LED Status Indicators

Read this chapter for information about LED status indicators.

What This Chapter Contains

Interpret the Status

Indicators

Module Status

Network Activity

Network Status

POINTBus Status

System Power

Field Power

43248aent

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

Indication

Module Status

Off

Probable Cause

Recommended Action

No power applied to device

Apply power to the device.

None

Flashing

LED cycle power test (module self-test) present.

Red/Green

Solid Green

Flashing Red

Device is operating normally.

None

Recoverable fault has occurred:

Firmware (NVS) update present.

Address switches changed.

Complete firmware update.

Verify address switches.

Solid Red

Unrecoverable fault has occurred:

Self-test failure present (checksum failure, or

ramtest failure at cycle power).

Replace adapter.

Firmware fatal error present.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

6-2

LED Status Indicators

Indication

Probable Cause

Recommended Action

Network Activity

Off

No link established.

Verify network cabling, and correct, as needed.

None

Flashing

Transmit or receive activity present.

Green/Off

Steady Green

Network Status

Off

Link established.

None

Device not initialized. The module does not have an Apply power to device, verify IP address, and correct, as

IP address.

needed.

Flashing Green

Solid Green

Flashing Red

Solid Red

No CIP connections present. Device has an IP

address, but no CIP connections are established.

None

CIP connections present. Device online and has an None

IP address, and CIP connections are established.

One or more CIP connections has timed-out.

Check for I/O module failure and controller operation, and

correct, as needed.

Duplicate IP address detected.

Verify IP address setting and correct, as needed.

None

Flashing

Red/Green

The module is performing a self-test (only occurs

during cycle power test).

POINTBus Status

Off

Device not powered - check module status

indicator.

Apply power to device.

None

Flashing

LED cycle power test present.

Red/Green

Flashing Red

Recoverable fault occurred:

• At cycle power the number of expected

modules does not equal the number of

modules present

• Configure chassis size.

• A module is missing

• Node fault (I/O connection timeout)

occurred.

• Check for missing module and reinstall as needed.

• Check for I/O module failure and correct as needed.

Solid Red

Unrecoverable fault occurred - the adapter is bus

off.

1. Cycle power to device.

2. If condition persists, replace device.

Flashing Green

Solid Green

Firmware (NVS) update in progress.

None

Adapter online with connections established

(normal operation, Run mode).

System Power

Off

Not active; field power is off or dc-dc converter

problem present.

1. Verify power is on, and apply power if needed.

2. Verify backplane power not exceeded, and correct.

3. Replace 1734-AENT module.

Green

System power is on; dc-dc converter is active (5V). None

Field Power

Off

Not active; field power is off.

Power is on; 24V is present.

Apply field power.

None

Green

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Adapter Web Pages

Read this appendix for information about the adapter Web page

diagnostics that offer extensive internal and network diagnostics.

What This Appendix

Contains

For Information About How to

Work with the H o me P a ge

See Page

A -1

Work with the D i agnostics Pages

Work with the C o nfiguration Pages

Work with the B r owse C h assis Page

A -3

A -10

A -15

Use the adapter diagnostics Home page to access other adapter

diagnostics Web pages and see the following information.

Work with the Home Page

• Host Name

• Module Description

• Module Location

• IP Address

• Ethernet Address (MAC)

• DHCP Enabled

• Product Revision

• Serial Number

• Status

• Auto Negotiate

• Media Speed

• Half or Full Duplex

To display and work with the adapter diagnostics Home page, follow

these procedures.

Make sure that your PC Internet LAN setting and your

IMPORTANT

TCP/IP settings are configured to access the subnet on

which your adapter communicates.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-2

Adapter Web Pages

You must use Series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

1. From a browser such as Netscape or Microsoft Internet Explorer,

enter the adapter IP address to see the Home page.

Enter the adapter IP

address to see the

Home page.

2. From the Home page, click Expand to expand options, as in the

figure, or Minimize to see Diagnostics, Configuration, and

Browse Chassis options without the expansion.

Click Expand to

expand options.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-3

3. From the Home page, complete one of these, as desired.

• Click one of these to go to http://www.ab.com/.

– Allen-Bradley logo at the top of the page

– Visit AB.com for additional information statement under

Resources

• Click Rockwell Automation at the top right to go to

http://www.rockwellautomation.com/.

• Click these to see additional diagnostics Web pages.

– Diagnostics - Diagnostic overview, Network Settings,

Ethernet Statistics, I/O Connections, Diagnostic messaging

– Configuration - Identity, Network, Services

– Browse chassis

To work with the Diagnostics options, follow these procedures.

Work with the Diagnostics

Pages

1. From the Home page, click Diagnostics or Expand to see the

following diagnostics options from the panel at the left.

• Diagnostic overview

• Network settings

• Ethernet statistics

• I/O connections

• Diagnostic messaging

2. From from the top of the page, as shown in the figure, if

desired, type a refresh rate, noting that the default is 15 seconds.

3. From the panel at the left or tabs at the top of the page, as

shown in the figure, click one of the diagnostics options to see

the corresponding page.

Click tabs to see the

corresponding page.

Click from this panel

to see the

corresponding page.

Type a

refresh

rate.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-4

Adapter Web Pages

Use the Diagnostic Overview Page

To use the Diagnostic Overview page to view general diagnostics

information, follow this procedure.

1. From the Web page, click Diagnostic Overview from the tab at

the top of the page or panel on the left.

You see the Diagnostic Overview page.

2. From the Diagnostic Overview page, view the following.

• Ethernet Link Status

– Media Speed

– Half or Full Duplex

– Autonegotiate Status

• System Resource Utilitization

– CPU Utilization

– Module Uptime

• CIP Connection Statics

– Current CIP MSG Connections

– CIP MSG Connection Limit

– Max Msg Connections Observed

– Current CIP I/O Connections

– CIP I/O Connection Limit

– Max I/O Connections Observed

– Conn Opens

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-5

– Open Errors

– Conn Closes

– Close Errors

– Conn Timeout

– Status

• Module Settings

– Chassis Size

– Switches

Use the Network Settings Page

To use the Network Settings page to view network related

information, follow this procedure.

1. From the Web page, click Network Settings from the tab at the

top of the page or panel on the left.

You see the Network Settings page.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-6

Adapter Web Pages

2. From the Network Settings page, view the following.

• Network Interface

– Ethernet Address (MAC)

– IP Address

– Subnet Mask

– Default Gateway

– Primary Name Server

– Secondary Name Server

– Default Domain Name

– Host Name

– Name Resolution

• Ethernet Interface Configuration

– How the Network Configuration was obtained -

Static or Dynamic

• Ethernet Link

– Media Speed

– Half or Full Duplex

– Autonegotiate Status

Use the Ethernet Statistics Page

To use the Ethernet Statistics page to view information about the

Ethernet link and interface and media counters, use this procedure.

1. From the Web page, click Ethernet Statistics from the tab at the

top of the page or panel on the left.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-7

You see the Ethernet Statistics page.

2. From the Ethernet Statistics page, view the following.

• Ethernet Link

– Media Speed, Half or Full Duplex, Autonegotiate Status

• Interface Counters

– In Octets, In UCast Packets, In NUcast Packets,

In Discards, In Errors, In Unknown Protos,

Out Octets, Out Ucast Packets, Out NUcast Packets,

Out Discards, Out Errors

• Media Counters

– Alignment Errors

– FCS Errors

– Single Collisions

– Multiple Collisions

– SQE Test Errors

– Deferred Transmissions

– Late Collisions

– Excessive Collisions

– MAC Transmit Errors

– Carrier Sense Errors

– Frame Too Long

– Mac Receive Errors

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-8

Adapter Web Pages

Use the I/O Connections Page

To use the I/O Connections page to view CIP I/O (Class 1)

connection information, follow this procedure.

1. From the Web page, click I/O Connections from the tab at the

top of the page or panel on the left.

You see the I/O Connections page.

The top value

in this column

representing

Lost shows

the number of

packets from

the source

missing.

The value for

Slot shows the

slot number of

the I/O module

this connection

is controlling.

2. From the I/O Connections page, view the following.

• Connection Number

• Uptime

• Receive and Transmit (Rcv/Xmt)

• Connection ID

• Source IP Address with an indication of the following

– (O) for originator

– (T) for target

• Destination IP Address

• Multicast Address

• Requested Packet Interval (RPI)

• Lost/Slot that shows the number of lost packets and the slot

number for the connection, with a slot value of 0 indicating that

this is a rack-optimized connection

• Size of data in bytes

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-9

Use the Diagnostic Messaging Page

To use the Diagnostic Messaging page to execute explicit,

unconnected message services, use this procedure.

1. From the Web page, click Diagnostic Messaging from the tab at

the top of the page or panel on the left.

You see the Diagnostic Messaging page.

2. From the Diagnostic Messaging page, enter the following.

• Service - choose either Get Attribute Single or Get Attributes All

• I/O Module Slot Position (0 to 63 decimal)

• Class (decimal)

• Instance (decimal)

• Attribute (decimal)

• Timeout

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-10

Adapter Web Pages

3. From the Diagnostic Messaging page, click Submit to see values

similar to that in the figure.

To work with the Configuration pages, follow these procedures,

noting that values on these pages are stored in and retrieved from

non-volatile memory.

Work with the

Configuration Pages

The values on these pages are in non-volatile memory.

IMPORTANT

Changes to these parameters do not take effect until

you reset or cycle power th the 1734-AENT adapter.

If you set the thumbwheels on the 1734-AENT adapter

IMPORTANT

to the value 888 and then power cycle the module, the

following occurs:

• The DHCP Enabled function is enabled (set to

True).

• The Ethernet link is negotiated automatically. The

Auto Negotiate function is set to True.

• The Web server is enabled. The Disabled Web

Server function is disabled.

• The password for this page resets to the factory

default. The word password is the factory default

password.

Note the value of the switches before you enter the 888

value because you return the adapter to those values

once this process is complete.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-11

1. From the Home page, click Configuration or Expand to see the

Configuration options, if needed.

2. From the Configuration page, click one of these.

• Identity

• Network

• Services

You see a dialog prompting you for a user name and password,

as shown in the figure that shows a typical example, noting that

your dialog may look different, depending on your operating

system and browser.

3. From the user name and password dialog, enter values, noting

the following.

• The values for user name and password are case sensitive.

• The default user name is admin.

• The default password is password.

4. From the user name and password dialog, click OK to log in,

noting that after you log in you can go to any of the

Configuration pages without logging in again.

5. Refer to the section of this manual that describes which of these

you clicked: Identity, Network, Services.

Use the Identity Page

To use the Identify page to make entries for the host name, module

description, module location, and chassis size, use this procedure.

1. From the Web page, click Identity from the tab at the top of the

page or panel on the left.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-12

Adapter Web Pages

You see the Identity page.

2. From the Identity page, complete entries for the following,

noting that the description and location help you identify where

modules are in the facility.

• Host Name - the name a Domain Name Server uses to resolve

this adapter’s IP address

• Module Description

• Module Location

• Chassis Size - the value that shows the number of POINT I/O

mdoules plus the adapter. This value must match the number

of I/O modules plus one for the adapter before any I/O

connections are allowed.

3. From the Identity page, click Apply Changes to save the

modified values.

Use the Network Configuration Page

To use the Network Configuration page to make entries for enabling

or disabling DHCP and setting TCP/IP parameters and Ethernet link

operation, follow this procedure.

1. From the Web page, click Network from the tab at the top of the

page or panel on the left.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-13

You see the Network Configuration page.

2. From the Network Configuration page, complete these entries,

noting that values for Network Interface are disabled when

DHCP is Dynamic DHCP and port speed and duplex mode are

disabled when Autonegotiate Speed and Duplex is selected.

• For Initial Network Configuration

Ethernet Interface Configuration

- Static

- Dynamic DHCP

• For Network Interface, select from these choices.

IP Address

Subnet Mask

Gateway Address

Primary Name Server

Secondary Name Server

Domain Name

• For Ethernet Link, select from these choices.

Autonegotiate Status

- Autonegotiate Speed and Duplex

- Force Speed and Duplex

Select Port Speed - 10 megabits, 100 megabits

Select Duplex Mode - Half Duplex, Full Duplex

3. From the Network Configuration page, click Apply Changes to

save the modified values.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-14

Adapter Web Pages

Use the Services Page

To use the Services page to change the Configuration web page’s

password or disable the Web server, complete these procedures.

1. From the Web page, click Services from the tab at the top of the

page or panel on the left.

You see the Services page.

2. From the Services page, make these entries.

• Click in the Enable box to change whether the Web server runs

after the module is reset.

• Change the password by typing the new value for New

Password and Confirm Password, noting the following.

– The entry is case sensitive.

– The default value is the word password.

3. From the Services page, click Apply Changes.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-15

Use the Browse Chassis page for the following.

Work with the Browse

Chassis Page

• See what modules are present on the system.

• Run a query from slot 1 to slot 63.

• Display the modules found based on the query.

• Provide an easy way to see what modules the adapter is

recognizing on your system.

To work with the Browse Chassis page, follow these procedures.

1. From the Home page, click Browse Chassis.

Check Increase timeout to increase

the time of the browse query and time

the modules get to respond to the

query, which is useful when browsing

a busy system.

2. From the Browse Chassis page, leave the Display compact check

box unchecked, if desired, unless you want to decrease the font

size, making it easier to read the full page after the query.

3. From the Browse Chassis page, check the Increase timeout

check box so a check mark appears, if desired.

This increases the time of the browse query and time the

modules get to respond to the query. This function is useful

when you are browsing a busy system.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-16

Adapter Web Pages

4. From the Browse Chassis page, click Start to run the query,

noting that you see a page such as the one in the the figure,

which shows that module hyperlinks are disabled while

browsing before the query completes or is cancelled.

Before the

query

completes,

this note

about the

disabled

module

hyperlinks

appears.

Before the query finds the module, the

If there is no response to the query, the

Module not found message appears.

Before the query completes,

module hyperlinks are inactive.

Requesting message appears.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Adapter Web Pages

A-17

After completion of a query, here is how a typical Browse

Chassis page looks with the module hyperlinks active and the

Display compact check box unchecked.

Click a module hyperlink to

view information about the

module.

Here is how a typical Browse Chassis page looks with the

Display compact check box checked.

Click a module hyperlink to

view information about the

module.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

A-18

Adapter Web Pages

5. From the Browse Chassis page, to view information about a

particular module, click the module’s Module Description

hyperlink.

You see a page showing this information about the module:

• Product Name

• Vendor

• Product Type

• Product Code

• Module Revision

• Serial Number

• Status

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Configure the RSLinx Ethernet

Communication Driver

To communicate with your 1734-AENT adapter over your network

you must configure the RSLinx Ethernet communication driver

(AB_ETH) or the EtherNet/IP driver (AB-ETHIP). You can configure

the AB_ETH driver with the IP addresses of all the Ethernet devices on

your system. You need one of these drivers to download the example

application programs in this manual.

What This Appendix

Contains

See the table for a list of the contents of this appendix and where to

find specific information:

For Information About

See Page

B -1

Install the R S L i nx Software

C o nfigure the A B _E TH D r iver

Configure the AB_ETHIP Driver

B -2

B -4

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

Use this procedure to install RSLinx software on your computer.

Install the RSLinx Software

1. Insert the CD in the CD-ROM drive.

Note that the CD-ROM supports Windows Autorun. Once

inserted into the CD-ROM drive, if you have Autorun configured,

the installation automatically starts at the first setup screen.

If Autorun is not configured for your CD-ROM drive, go to

step 2.

2. From the Start menu, choose Run.

You see the Run dialog.

3. Type d:/setup (if it doesn’t appear automatically), where d: is

your CD-ROM driver letter.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

B-2

Configure the RSLinx Ethernet Communication Driver

4. Click OK.

You see the progress bar, followed by the welcome screen.

To configure the AB-ETH Ethernet communication driver perform the

following steps:

Configure the AB_ETH

Driver

1. Start RSLinx software.

2. From the Communications menu, select Configure Drivers.

3. Click the arrow to the right of the Available Driver Types box.

The Available Driver Types list appears.

4. Select Ethernet Devices and click Add/New.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the RSLinx Ethernet Communication Driver

B-3

You are prompted to name the driver.

5. Select the default driver name (for example, AB_ETH-1) or type

in a name and click OK.

The Configure driver dialog appears with the Station Mapping

page open.

6. Click Add New and enter the IP address or Host Name of your

Ethernet device (for example, 10.88.70.4, Pump1).

7. Repeat step 6 for each additional Ethernet device you need to

access.

8. After entering the IP addresses, click Apply.

9. Click OK to close the Configure driver window.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

B-4

Configure the RSLinx Ethernet Communication Driver

The new driver appears in the list of configured drivers. (Your list

displays the drivers you configured on your workstation.)

10. Close RSLinx software

To configure the AB-ETHIP Ethernet communication driver, perform

the following steps.

Configure the AB_ETH/IP

Driver

1. Start RSLinx software.

2. From the Communications menu, select Configure Drivers.

3. Click the arrow to the right of the Available Driver Types box.

The Available Driver Types list appears.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Configure the RSLinx Ethernet Communication Driver

B-5

4. Select EtherNet/IP Devices and click Add/New.

You see this window.

5. Make sure the Browse Local Subnet button is selected.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

B-6

Configure the RSLinx Ethernet Communication Driver

RSLinx software browses your local subnet and automatically

reads the IP address.

6. Click OK.

The AB-ETHIP driver is now configured and appears in the

configured drivers window.

7. Close RSLinx software

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

1734 POINT I/O Module/RSLogix 5000

Controller Tag Reference

Read this appendix for information about tag references.

What This Appendix

Contains

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

1734 POINT I/O Catalog

Numbers

1734 POINT I/O

Catalog Number

RSLogix5000 Module Description

Digital Modules

1734-IA2/C

2 POINT 120V ac Input

1734-IB2/C

2 POINT 10V…28V dc Input, Sink

1734-IB4/C

4 POINT 10V…28V dc Input, Sink

1734-IM2/C

1734-IV2/C

2 POINT 240V ac Input

2 POINT 10V…28V dc Input, Source

1734-IV4/C

4 POINT 10V…28V dc Input, Source

1734-OA2/C

1734-OB2E/C

1734-OB2EP/C

1734-OB4E/C

1734-OV2E/C

1734-OV4E/C

1734-OW2/C

1734-OX2/C

Analog Modules

1734-IE2C/C

1734-IE2V/C

1734-IR2/C

2 POINT 120V ac Output

2 POINT 10V…28V dc Electronically Fused Output, Source

2 POINT 10V…28V dc Electronically Fused Protected Output, Source

4 POINT 10V…28V dc Electronically Fused Output, Source

2 POINT 10V…28V dc Electronically Fused Output, Sink

4 POINT 10V…28V dc Electronically Fused Output, Sink

2 POINT ac/dc Relay Output

2 POINT Relay Output N.O./N.C.

2 Channel Analog Current Input

2 Channel Analog Voltage Input

2 Channel RTD Input

1734-IT2I/C

1734-OE2C/C

1734-OE2V/C

2 Channel Thermocouple Input, Isolated

2 Channel Analog Current Output

2 Channel Analog Voltage Output

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-2

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734 POINT I/O

Catalog Number

RSLogix5000 Module Description

Specialty I/O

1734-232ASC/C

1734-IJ/C

1 Channel ASCII Interface Module

1 Channel 5V dc Encoder/Counter

1734-IK/C

1 Channel 15…24V dc Encoder/Counter

1 Channel Synchronous Serial Interface

1 Channel 15…24V dc Very High-speed Counter

1 Channel 5V dc Very High-speed Counter

1734-SSI/C

1734-VHSC24/C

1734-VHSC5/C

Note that all POINT I/O modules must be series C or above for

RSLogix 5000 software, version 11, compatibility.

The 1734-232ASC/A (series A) is presently the only exception to the

series C requirement. With RSLogix 5000 software, version 11, use it

as a generic 1734 module. With RSLogix 5000 software, version 12 or

later, it is directly supported.

Valid Number Ranges for

RSLogix 5000 Data Types

Type

BIT

Number

1 Bit

Range

0 or 1

SINT

INT

8 Bit

-128…+127

16 Bit

32 Bit

-32,768…32,767

-2,147,483,648…2,147,483,647

DINT

Accepted parameter values are dependent on POINT I/O module type

and tag type.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-3

Digital 2 POINT Input

1734-IA2

2 POINT 120V ac Input

1734-IB2

2 POINT 10V…28V dc Input, Sink

1734-IM2

2 POINT 240V ac Input

1734-IV2

2 POINT 10V…28V dc Input, Source

Configuration Data

Data Type

Default

Value

Valid Data Values

(1)

Filter Off On Time - POINT 0

INT

1,000

-32,768…32,767 µs

(0…65,535)

(1)

Filter On Off Time - POINT 0

Filter Off On Time - POINT 1

Filter On Off Time - POINT 1

INT

-32,768…32,767 µs

(0…65,535)

(1)

-32,768…32,767 µs

(0…65,535)

-32,768…32,767 µs

(0…65,535)

Input Data

Data Type

Default

Value

Valid Data Values

Input Data - POINT 0, 1

SINT, BIT

0=Off

1=On

Output Data

None

Data Type

Default

Value

Valid Data Values

(1)

POINT I/O Modules support the Unsigned Integer data type UINT

(0 to 65,535 range).

RSLogix 5000 software supports the signed Integer data type INT

(-32,768 to +32,767 range).

To enter Filter values from +32,768 to +65,535 µs, use this

conversion formula:

Desired Filter Value (in µs) - 65536 = Entered Filter Value (in µs).

As an example, for a 40 ms filter time, 40000 - 65536 = -25536

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-4

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

Digital 4 POINT Input

1734-IB4

4 POINT 10…28V dc Input, Sink

1734-IV4

4 POINT 10…28V dc Input, Source

Configuration Data

Data Type

Default

Value

Valid Data Values

(1)

Filter Off On Time - POINT 0

INT

1,000

-32,768…32,767 µs

(0…65,535)

Filter On Off Time - POINT 0

Filter Off On Time - POINT 1

Filter On Off Time - POINT 1

Filter Off On Time - POINT 2

Filter On Off Time - POINT 2

Filter Off On Time - POINT 3

Filter On Off Time - POINT 3

INT

-32,768…32,767 µs

(0…65,535)

-32,768…32,767 µs

(0…65,535)

-32,768…32,767 µs

(0…65,535)

-32,768…32,767 µs

(0…65,535)

-32,768…32,767 µs

(0…65,535)

(1)

-32,768…32,767 µs

(0…65,535)

(1)

-32,768…32,767 µs

(0… 65,535)

Input Data

Data Type

Default

Value

Valid Data Values

Input Data - POINT 0, 1, 2, 3

SINT, BIT

0=Off

1=On

Output Data

None

Data Type

Default

Value

Valid Data Values

(1)

POINT I/O Modules support the Unsigned Integer data type UINT

(0 to 65,535 range).

RSLogix 5000 software supports the signed Integer data type INT

(-32,768 to +32,767 range).

To enter Filter values from +32,768 to +65,535 µs, use this conversion

formula:

Desired Filter Value (in µs) - 65536 = Entered Filter Value (in µs).

As an example, for a 40 ms filter time, 40000 - 65536 = -25536

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-5

Digital 2 POINT Output –

Without Diagnostic Status

1734-OA2

2 POINT 120V ac Output

1734-OW2

2 POINT ac/dc Relay Output

1734-OX2

2 POINT Relay Output N.O./N.C.

Configuration Data

Data Type

SINT, BIT

Default

Value

Valid Data Values

Fault Mode - POINT 0, 1

Fault Value - POINT 0, 1

Program Mode - POINT 0, 1

Program Value - POINT 0, 1

0=Fault Value

1=Hold Last State

0=Off

1=On

0=Program Value

1=Hold Last State

0=Off

1=On

Input Data

Data Type

Default

Value

Valid Data Values

None

Output Data

Data Type

Default

Value

Valid Data Values

Output Data - POINT 0, 1

SINT, BIT

0=Off

1=On

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-6

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

Digital 2 POINT Output –

With Over Load and Open

Load Diagnostic Status

1734-OB2E

2 POINT 10V…28V dc Electronically Fused Output, Source

1734-OB2EP

2 POINT 10V…28V dc Electronically Fused Protected Output, Source

Configuration Data

Data Type

SINT, BIT

Default

Value

Valid Data Values

Fault Mode - POINT 0, 1

Fault Value - POINT 0, 1

Program Mode - POINT 0, 1

Program Value - POINT 0, 1

0=Fault Value

1=Hold Last State

0=Off

1=On

0=Program Value

1=Hold Last State

0=Off

1=On

No Load Enable - POINT 0, 1

(Wire Off Diagnostic)

0=Disabled

1=Enabled

Auto Restart Enable - POINT 0, 1

(Over Load Behavior)

0=Latch Off

1=Auto Retry

Fault Latch Enable - POINT 0, 1

(Open Load or Over Load)

0=No Latching

1=Alarms Latch

Input Data

Data Type

Default

Value

Valid Data Values

Status Data - POINT 0, 1

(Open Load or Over Load)

SINT, BIT

0=Off

1=On (Load Fault)

Output Data

Data Type

Default

Value

Valid Data Values

Output Data - POINT 0, 1

SINT, BIT

0=Off

1=On

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-7

Digital 2 POINT Output –

With Over Load Diagnostic

Status

1734-OV2E

2 POINT 10V…28V dc Electronically Fused Output, Sink

Configuration Data

Data Type

SINT, BIT

Default

Value

Valid Data Values

Fault Mode - POINT 0, 1

Fault Value - POINT 0, 1

Program Mode - POINT 0, 1

Program Value - POINT 0, 1

0=Fault Value

1=Hold Last State

0=Off

1=On

0=Program Value

1=Hold Last State

0=Off

1=On

Auto Restart Enable - POINT 0, 1

(Over Load Behavior)

0=Latch Off

1=Auto Retry

Fault Latch Enable - POINT 0, 1

(Over Load)

0=No Latching

1=Alarms Latch

Input Data

Data Type

Default Valid Data Values

Value

Status Data - POINT 0, 1

(Over Load)

SINT, BIT

0=Off

1=On (Load Fault)

Output Data

Data Type

Default Valid Data Values

Value

Output Data - POINT 0, 1

SINT, BIT

0=Off

1=On

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-8

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

Digital 4 POINT Output –

With Over Load and Open

Load Diagnostic Status

1734-OB4E

4 POINT 10V…28V dc Electronically Fused Output, Source

Configuration Data

Data Type Default Valid Data Values

Value

Fault Mode - POINT 0, 1, 2, 3

Fault Value - POINT 0, 1, 2, 3

Program Mode - POINT 0, 1, 2, 3

Program Value - POINT 0, 1, 2, 3

SINT, BIT

0=Fault Value

1=Hold Last State

0=Off

1=On

0=Program Value

1=Hold Last State

0=Off

1=On

No Load Enable - POINT 0, 1, 2, 3

(Wire Off Diagnostic)

0=Disabled

1=Enabled

Auto Restart Enable - POINT 0, 1, 2, 3

(Over Load Behavior)

0=Latch Off

1=Auto Retry

Fault Latch Enable - POINT 0, 1, 2, 3

(Open Load or Over Load)

0=No Latching

1=Alarms Latch

Input Data

Data Type Default Valid Data Values

Value

Status Data - POINT 0, 1, 2, 3

(Open Load or Over Load)

SINT, BIT

0=Off

1=On (Load Fault)

Output Data

Data Type Default Valid Data Values

Value

Output Data - POINT 0, 1, 2, 3

SINT, BIT

0=Off

1=On

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-9

Digital 4 POINT Output –

With Over Load Diagnostic

Status

1734-OV4E

4 POINT 10V…28V dc Electronically Fused Output, Sink

Configuration Data

Data Type Default Valid Data Values

Value

Fault Mode - POINT 0, 1, 2, 3

Fault Value - POINT 0, 1, 2, 3

Program Mode - POINT 0, 1, 2, 3

Program Value - POINT 0, 1, 2, 3

SINT, BIT

0=Fault Value

1=Hold Last State

0=Off

1=On

0=Program Value

1=Hold Last State

0=Off

1=On

Auto Restart Enable - POINT 0, 1, 2, 3

(Over Load Behavior)

0=Latch Off

1=Auto Retry

Fault Latch Enable - POINT 0, 1, 2, 3

(Over Load)

0=No Latching

1=Alarms Latch

Input Data

Data Type Default Valid Data Values

Value

Status Data - POINT 0, 1, 2, 3

(Over Load)

SINT, BIT

0=Off

1=On (Load Fault)

Output Data

Data Type Default Valid Data Values

Value

Output Data - POINT 0, 1, 2, 3

SINT, BIT

0=Off

1=On

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-10

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

Analog 2 Channel Input

1734-IE2C

2 Channel Analog Current Input

Configuration Data

Data Type Default Valid Data Values

Value

Low Engineering Channel 0

High Engineering Channel 0

Digital Filter Channel 0

INT

SINT

3,277

-32,768…32,767

16,383 -32,768…32,767

0…10,000 ms

Low Alarm Limit Channel 0

High Alarm Limit Channel 0

Low Low Alarm Limit Channel 0

High High Alarm Limit Channel 0

Range Type Channel 0

3,113

-32,768…32,767

16,547 -32,768…32,767

2,867 -32,768…32,767

16,793 -32,768…32,767

3=4…20 mA

8=0…20 mA

Limit Alarm Latch Channel 0

Alarm Disable Channel 0

SINT

0=No Latching

1=Alarms Latch

0=Alarms Enabled

1=Alarms Disabled

Low Engineering Channel 1

High Engineering Channel 1

Digital Filter Channel 1

INT

SINT

3,277

-32,768…32,767

16,383 -32,768…32,767

0…10,000 ms

Low Alarm Limit Channel 1

High Alarm Limit Channel 1

Low Low Alarm Limit Channel 1

High High Alarm Limit Channel 1

Range Type Channel 1

3,113

-32,768…32,767

16,547 -32,768…32,767

2,867 -32,768…32,767

16,793 -32,768…32,767

3=4-20 mA

8=0-20 mA

Limit Alarm Latch Channel 1

Alarm Disable Channel 1

SINT

0=No Latching

1=Alarms Latch

0=Alarms Enabled

1=Alarms Disabled

Notch Filter (Channel 0 & 1)

1=50 Hz

2=60 Hz

4=250 Hz

6=500 Hz

Real-time Sample (Channel 0 & 1)

INT

100

0…10,000 ms

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-11

1734-IE2C

2 Channel Analog Current Input

Input Data

Data Type

Default Valid Data Values

Value

Data Channel 0

INT

-32,768…32,767

Data Channel 1

INT

Status Byte Channel 0

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Status Byte Channel 1

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Output Data

Data Type

Default Valid Data Values

Value

None

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-12

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-IE2V

2 Channel Analog Voltage Input

Configuration Data

Data Type Default Valid Data Values

Value

Low Engineering Channel 0

High Engineering Channel 0

Digital Filter Channel 0

INT

SINT

-32,768…32,767

10,000 -32,768…32,767

0…10,000 ms

Low Alarm Limit Channel 0

High Alarm Limit Channel 0

Low Low Alarm Limit Channel 0

High High Alarm Limit Channel 0

Range Type Channel 0

500

-32,768…32,767

9,500 -32,768…32,767

200 -32,768…32,767

9,800 -32,768…32,767

0=-10…+10V

2=0…10V

Limit Alarm Latch Channel 0

Alarm Disable Channel 0

SINT

0=No Latching

1=Alarms Latch

0=Alarms Enabled

1=Alarms Disabled

Low Engineering Channel 1

High Engineering Channel 1

Digital Filter Channel 1

INT

SINT

-32,768…32,767

10,000 -32,768…32,767

0…10,000 ms

Low Alarm Limit Channel 1

High Alarm Limit Channel 1

Low Low Alarm Limit Channel 1

High High Alarm Limit Channel 1

Range Type Channel 1

500

-32,768…32,767

9,500 -32,768…32,767

200 -32,768…32,767

9,800 -32,768…32,767

0=-10…+10V

2=0…10V

Limit Alarm Latch Channel 1

Alarm Disable Channel 1

SINT

0=No Latching

1=Alarms Latch

0=Alarms Enabled

1=Alarms Disabled

Notch Filter (Channel 0 & 1)

1=50 Hz

2=60 Hz

4=250 Hz

6=500 Hz

Real-time Sample (Channel 0 & 1)

INT

100

0…10,000 ms

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-13

1734-IE2V

2 Channel Analog Voltage Input

Input Data

Data Type

Default Valid Data Values

Value

Data Channel 0

INT

-32,768…32,767

Data Channel 1

INT

Status Byte Channel 0

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Status Byte Channel 1

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Output Data

Data Type

Default Valid Data Values

Value

None

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-14

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-IR2

2 Channel RTD Input

Configuration Data

Data Type

INT

Default Value

1,000

Valid Data Values

-32,768…32,767

0…10,000 ms

Low Engineering Channel 0

High Engineering Channel 0

Digital Filter Channel 0

INT

5,000

INT

Low Alarm Limit Channel 0

High Alarm Limit Channel 0

Low Low Alarm Limit Channel 0

High High Alarm Limit Channel 0

Limit Alarm Latch Channel 0

INT

-32,768

32,767

-32,768

32,767

-32,768…32,767

INT

SINT

0=No Latching

1=Alarms Latch

Alarm Disable Channel 0

Sensor Type Channel 0

SINT

0=Alarms Enabled

1=Alarms Disabled

0=Ohms

1=100 ΩPt α385

2=200 ΩPt α385

5=100 ΩJPt α 3916

6=200 ΩJPt α3916

9=10 ΩCu α427

10=120 ΩNi α 672

11=100 ΩNi α618

12=120 ΩNi α618

Temperature Mode Channel 0

SINT

0=Custom Scale

1=°C

2=°F

3=°K

4=°R

Low Engineering Channel 1

High Engineering Channel 1

Digital Filter Channel 1

INT

SINT

1,000

5,000

-32,768…32,767

0…10,000 ms

Low Alarm Limit Channel 1

High Alarm Limit Channel 1

Low Low Alarm Limit Channel 1

High High Alarm Limit Channel 1

Limit Alarm Latch Channel 1

-32,768

32,767

-32,768

32,767

-32,768…32,767

0=No Latching

1=Alarms Latch

Alarm Disable Channel 1

SINT

0=Alarms Enabled

1=Alarms Disabled

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-15

1734-IR2

2 Channel RTD Input

Configuration Data

Data Type

Default Value

Valid Data Values

Sensor Type Channel 1

SINT

0=Ohms

1=100 ΩPt α 385

2=200 ΩPt α385

5=100 ΩJPt α 3916

6=200 ΩJPt α3916

9=10 ΩCu α427

10=120 ΩNi α 672

11=100 ΩNi α618

12=120 ΩNi α618

Temperature Mode Channel 1

SINT

0=Custom Scale

1=°C

2=°F

3=°K

4=°R

Notch Filter (Channel 0 & 1)

0=50 Hz

1=60 Hz

2=100 Hz

3=120 Hz

4=200 Hz

5=240 Hz

6=300 Hz

7=400 Hz

8=480 Hz

Input Data

Data Type

INT

Default Value

Valid Data Values

-32,768…32,767

Data Channel 0

Data Channel 1

Status Byte Channel 0

INT

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Status Byte Channel 1

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Output Data

Data Type

Default Value

Valid Data Values

None

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-16

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-IT2

2 Channel Thermocouple Input, Isol.

Configuration Data

Cold Junction Notch Filter

Cold Junction Mode

Data Type

SINT

Default Valid Data Values

Value

0=50 Hz

1=60 Hz

SINT

0=None

1=Channel 0

2=Channel 1

3=Average Both

Low Engineering Channel 0

High Engineering Channel 0

Alarm Disable Channel 0

INT

-32,768…32,767

INT

7,000

SINT

0=Alarms Enabled

1=Alarms Disabled

Limit Alarm Latch Channel 0

Notch Filter Channel 0

SINT

0=No Latching

1=Alarms Latch

0=50 Hz

1=60 Hz

2=100 Hz

3=120 Hz

4=200 Hz

5=240 Hz

6=300 Hz

7=400 Hz

8=480 Hz

Sensor Type Channel 0

SINT

0=mV

1=B

2=C

3=E

4=J

5=K

6=N

7=R

8=S

9=T

Digital Filter Channel 0

INT

0…10,000 ms

Low Alarm Limit Channel 0

High Alarm Limit Channel 0

Low Low Alarm Limit Channel 0

High High Alarm Limit Channel 0

-32,768

32,767

-32,768

32,767

-32,768…32,767

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-17

1734-IT2

2 Channel Thermocouple Input, Isol.

Configuration Data

Data Type

Default Valid Data Values

Value

Temperature Mode Channel 0

SINT

0=mV/Custom Scale

1=°C

2=°F

3=°K

4=°R

Cold Junction Enable Channel 0

SINT

0=Disabled

1=Enabled

Cold Junction Offset Channel 0

Low Engineering Channel 1

High Engineering Channel 1

Alarm Disable Channel 1

INT

SINT

0…7,000 (0.00…70.00)

-32,768…32,767

7,000

-32,768…32,767

0=Alarms Enabled

1=Alarms Disabled

Limit Alarm Latch Channel 1

Notch Filter Channel 1

SINT

0=No Latching

1=Alarms Latch

0=50 Hz

1=60 Hz

2=100 Hz

3=120 Hz

4=200 Hz

5=240 Hz

6=300 Hz

7=400 Hz

8=480 Hz

Sensor Type Channel 1

SINT

0=mV

1=B

2=C

3=E

4=J

5=K

6=N

7=R

8=S

9=T

Digital Filter Channel 1

INT

0…10,000 ms

Low Alarm Limit Channel 1

High Alarm Limit Channel 1

Low Low Alarm Limit Channel 1

High High Alarm Limit Channel 1

-32,768

32,767

-32,768

32,767

-32,768…32,767

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-18

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-IT2

2 Channel Thermocouple Input, Isol.

Configuration Data

Data Type

Default Valid Data Values

Value

Temperature Mode Channel 1

SINT

0=mV/Custom Scale

1=°C

2=°F

3=°K

4=°R

Cold Junction Enable Channel 1

SINT

0=Disabled

1=Enabled

Cold Junction Offset Channel 1

INT

0…7,000 (0.00…70.00)

Input Data

Data Type

Default Valid Data Values

Value

Data Channel 0

INT

-32,768…32,767

Data Channel 1

INT

Status Byte Channel 0

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Status Byte Channel 1

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Bit 4 LowLowAlarm

Bit 5 HighHighAlarm

Bit 6 Underrange

Bit 7 Overrange

Cold Junction Data

INT

-32,768…32,767

Output Data

Data Type

Default Valid Data Values

Value

None

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-19

Analog 2 Channel Output

1734-OE2C

2 Channel Analog Current Output

Configuration Data

Data Type

Default Valid Data Values

Value

Fault Value Channel 0

Program Value Channel 0

Low Engineering Channel 0

High Engineering Channel 0

Low Limit Channel 0

INT

SINT

-32,768…32,767

1,638

8,191

-32,768

32,767

High Limit Channel 0

Range Type Channel 0

0=4…20 mA

2=0…20 mA

Fault Mode Channel 0

Idle Mode Channel 0

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

Limit Alarm Latch Channel 0

Alarm Disable Channel 0

SINT

0=No Latching

1=Alarms Latch

0=Alarms Enabled

1=Alarms Disabled

Fault Value Channel 1

Program Value Channel 1

Low Engineering Channel 1

High Engineering Channel 1

Low Limit Channel 1

INT

SINT

-32,768…32,767

1,638

8,191

-32,768

32,767

High Limit Channel 1

Range Type Channel 1

0=4…20 mA

2=0…20 mA

Fault Mode Channel 1

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-20

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-OE2C

2 Channel Analog Current Output

Configuration Data

Data Type

Default Valid Data Values

Value

Idle Mode Channel 1

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

Limit Alarm Latch Channel 1

Alarm Disable Channel 1

SINT

0=No Latching

1=Alarms Latch

0=Alarms Enabled

1=Alarms Disabled

Input Data

Data Type

Default Valid Data Values

Value

Status Byte Channel 0

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Status Byte Channel 1

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Output Data

Data Type

Default Valid Data Values

Value

Data Channel 0

Data Channel 1

INT

-32,768…32,767

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-21

1734-OE2V

2 Channel Analog Voltage Output

Configuration Data

Data Type

Default Valid Data Values

Value

Fault Value Channel 0

Program Value Channel 0

Low Engineering Channel 0

High Engineering Channel 0

Low Limit Channel 0

INT

SINT

-32,768…32,767

10,000

-32,768

32,767

High Limit Channel 0

Range Type Channel 0

1=0…10V

3=-10…+10V

Fault Mode Channel 0

Idle Mode Channel 0

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

Limit Alarm Latch Channel 0

Alarm Disable Channel 0

SINT

0=No Latching

1=Alarms Latch

0=Alarms Enabled

1=Alarms Disabled

Fault Value Channel 1

Program Value Channel 1

Low Engineering Channel 1

High Engineering Channel 1

Low Limit Channel 1

INT

SINT

-32,768…32,767

10,000

-32,768

32,767

High Limit Channel 1

Range Type Channel 1

1=0…10V

3=-10…+10V

Fault Mode Channel 1

Idle Mode Channel 1

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

SINT

0=Hold Last State

1=Go to Low Clamp

2=Go to High Clamp

3=Go to Fault Value

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-22

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-OE2V

2 Channel Analog Voltage Output

Configuration Data

Data Type

SINT

Default Valid Data Values

Value

Limit Alarm Latch Channel 1

Alarm Disable Channel 1

0=No Latching

1=Alarms Latch

SINT

0=Alarms Enabled

1=Alarms Disabled

Input Data

Data Type

Default Valid Data Values

Value

Status Byte Channel 0

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Status Byte Channel 1

SINT

Bit 0 Fault

Bit 1 Calibration

Bit 2 LowAlarm

Bit 3 HighAlarm

Output Data

Data Type

Default Valid Data Values

Value

Data Channel 0

Data Channel 1

INT

-32,768…32,767

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-23

Specialty I/O

1734-VHSC24

1 Channel 15…24V dc Very High-speed Counter

1734-VHSC5

1 Channel 5V dc Very High-speed Counter

Configuration Data

Data Type Default

Valid Data Values

Value

Counter Config

SINT

Config_0

Config_1

Config_2

Config_3

BIT 0

BIT 1

BIT 2

BIT 3

0000=0=Counter

0001=1=Encoder X1

0010=2=Encoder X2

0011=3=PWM

0100=4=Encoder X4

0101=5=Period/Rate

0110=6=Continuous/Rate

0111=7=Rate Measurement

1000=8=Pulse Generator

Mode_4

Mode_5

Mode_6

BIT 4

BIT 5

BIT 6

000=Store Count Disable

001=Store/Continue

010=Store/Wait/Resume

011=Store,Reset/Wait/Start

100=Store,Reset/Start

Z Input

BIT 7

0=Z Input Not Inverted

1=Z Input Is Inverted

Filter

SINT

BIT 0

BIT 1

BIT 2

BIT 3

120

(0x78H)

Filter_0

Filter_1

Filter_2

Filter_3

0000=No Filter

0001=50 kHz

0010=5 kHz

0100=500 Hz

1000=50 Hz

FilterA

FilterB

FilterZ

BIT 4

BIT 5

BIT 6

0=Input A/B/Z Not Filtered

1=Input A/B/Z Is Filtered

Decimal Position

SINT

Counter Config 0, 1, 2, 3, 4:

-128…+127 (0…255)

Counter Config 5, 6, & 7:

-4…+2

Time Base

(in 10 ms intervals)

INT

Counter Config 3 & 7 only:

0…3000 ms (10 ms…3 sec)

Gate Interval

(Product of Time Base x Gate

Interval must be ≤3000 ms)

SINT

Counter Config 3 & 7 only:

-128…+127 (0…200)

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-24

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-VHSC24

1 Channel 15…24V dc Very High-speed Counter

1734-VHSC5

1 Channel 5V dc Very High-speed Counter

Configuration Data

Data Type Default

Valid Data Values

Value

Scalar

SINT

Counter Config 5, 6, 8 only:

-128…+127 (0…255) Single Bit

only:

0, 1, 2, 4, 8, 16, 32, 64, -128

Output Ties 0

SINT

BIT 0

BIT 1

BIT 2

BIT 3

Out 0 Window 1

Out 0 Window 2

Out 0 Window 3

Out 0 Window 4

0=Output 0 Not Tied

1=Output 0 Tied to Window

Counter Config 3 (PWM):

Output 0 Window 1 PWM In

Output Ties 1

SINT

BIT 0

BIT 1

BIT 2

BIT 3

Out 1 Window 1

Out 1 Window 2

Out 1 Window 3

Out 1 Window 4

0=Output 1 Not Tied

1=Output 1 Tied to Window

Counter Config 3 (PWM):

Output 1 Window 1 PWM In

Rollover

DINT

16,777,215 1…16,777,216

Preset (< Rollover)

0…16,777,215

On Value 1

Off Value 1

On Value 2

Off Value 2

On Value 3

Off Value 3

On Value 4

Off Value 4

DINT

Counter Config 3, 5, 6, 7:

0…16,777,215

Counter Config 0, 1, 2, 4:

0 to Rollover Value

SS PWM Value

(<0 or >9500 =Hold Last State)

INT

0…9500

(0.00…95.00%)

SS Counter Control

SINT

BIT 0

SS Counter Reset

0=Count Unchanged

1=Count Cleared

SS Counter Preset

BIT 1

BIT 2

0=Count Unchanged

1=Count Set to Preset

SS Value Reset

0=Count Unchanged

(Stored / Accum. Count)

1=Count Cleared

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-25

1734-VHSC24

1 Channel 15…24V dc Very High-speed Counter

1734-VHSC5

1 Channel 5V dc Very High-speed Counter

Configuration Data

Data Type Default

Valid Data Values

Value

SS Output Control

SS Out 0 Force

SINT

BIT 0

0=Output Off

1=Output Forced On

SS Out 0 En

BIT 1

BIT 2

0=Output Disabled

1=Output Enabled

SS Out 0 Electronic Fuse

0=Auto Retry

1=Latch Off

SS Out 0 Diagnostic Speed BIT 3

0 < 8 ms Response

1=50 ms Response

SS Out 1 Force

BIT 4

BIT 5

BIT 6

0=Output Off

1=Output Forced On

SS Out 1 En

0=Output Disabled

1=Output Enabled

SS Out 1 Electronic Fuse

0=Auto Retry

1=Latch Off

SS Out 1 Diagnostic Speed BIT 7

0 < 8 ms Response

1=50 ms Response

To enter values from +128 to +255, use these conversion formulas:

Desired Decimal Position Value - 256 = Entered Decimal

Position Value.

As an example, for a divisor of 200, 200 - 256 = -56

Desired Gate Interval Value - 256 = Entered Gate Interval Value.

As an example, for a Gate Interval of 200, 200 - 256 = -56

Desired Scalar Value - 256 = Entered Scalar Value.

As an example, for a Scalar of 128, 128 - 256 = -128

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-26

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-VHSC24

1 Channel 15…24V dc Very High-speed Counter

1734-VHSC5

1 Channel 5V dc Very High-speed Counter

Input Data

Present Data

Stored Data

Data Type

Default Value

Valid Data Values

DINT

0…16,777,215

-2,147,483,648…2,147,483,64

(0…4,294,967,295)

Status

INT

Zero Frequency Detected

BIT 1

0=No Fault

1=Fault Detected

Stored Data Count_2

Stored Data Count_3

BIT 2

BIT 3

Cycles through 0, 1, 2, 3, 0,

Increments after update

A Input Status

B Input Status

Z Input Status

BIT 4

BIT 5

BIT 6

0=Input A/B/Z is Off

1=Input A/B/Z is On

Output Status_8 (Output 0)

Output Status_9 (Output 1)

BIT 8

BIT 9

0=Output is Off

1=Output is On

Output Fault_10 (Output 0)

Output Fault_11 (Output 1)

BIT 10

BIT 11

0=No Fault

1=Open or Over Load

Not Ready

BIT 13

BIT 14

BIT 15

0=Module Ready

1=Module Initializing

EEPROM Fault

0=No Fault

1=EEPROM data bad

Program Fault

0=No Fault

(incomplete / incorrect / conflict)

1=Bad Configuration

(See Program Fault Note on

the next page)

Stored Data

To interpret values from -2,147,483,648 to -1, use this conversion

formula:

Stored Data Tag Value + 4,294,967,296 = Actual Stored Data Tag

Value.

As an example, for a read value of -1,794,967,296:

-1,794,967,296 + 4,294,967,296 = 2,500,000,000 actual value

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-27

Program Fault

Programming Fault Error bit - If an incomplete, incorrect, or

conflicting set of configuration parameters is sent to the module, the

Program Fault bit will be asserted and an error code will be placed in

the Programming Error Code word (assembly 6816). The module will

not enter a normal operational state. Bit definitions (decimal) for the

error codes are:

An invalid assembly was chosen for poll consumption (0, 105,

or 106 are valid).

The decimal point position is outside of the acceptable range.

Counter 0 window ON & OFF values are equal and not zero OR

Counter 0 window ON & OFF value is greater than Rollover.

A tie has been connected to an unprogrammed window.

A configuration was selected that requires the scalar and none

was programmed OR

Multiple scalars were selected.

The preset is out of range (Rollover).

A rollover of zero was programmed through PWM was not

selected OR

A rollover was programmed and PWM was selected OR

Rollover is out of range (>0x01000000).

A configuration requiring a time base was selected and no gate

interval was set OR

Gate interval is out of range (>200) OR

Product of time base and gate interval is greater than 3 seconds.

A time base was entered that is not a multiple of 10 OR

Time base is out of range (>3000, or 3 seconds).

ZF/BF/AF were selected and no filter was programmed OR

Multiple filters were selected.

A reserved configuration/mode was programmed.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-28

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-VHSC24

1 Channel 15…24V dc Very High-speed Counter

1734-VHSC5

1 Channel 5V dc Very High-speed Counter

Output Data

Data Type

Default Valid Data Values

Value

PWM Value

INT

0…9500

(0.00…95.00%)

Counter Control

Counter Reset

SINT

BIT 0

0=Count Unchanged

1=Count Cleared

Counter Preset

BIT 1

BIT 2

0=Count Unchanged

1=Count Set to Preset

Value Reset

0=Count Unchanged

(Stored / Accumulated Count)

1=Count Cleared

Output Control

SINT

BIT 0

Output 0 Force

0=Output Off

1=Output Forced On

Output 0 Enable

BIT 1

BIT 2

BIT 3

BIT 4

BIT 5

BIT 6

BIT 7

0=Output Disabled

1=Output Enabled

Output 0 Electronic Fuse

Output 0 Diagnostic Speed

Output 1 Force

0=Auto Retry

1=Latch Off

0< 8 ms Response

1=50 ms Response

0=Output Off

1=Output Forced On

Output 1 Enable

0=Output Disabled

1=Output Enabled

Output 1 Electronic Fuse

Output 1 Diagnostic Speed

0=Auto Retry

1=Latch Off

0< 8 ms Response

1=50 ms Response

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-29

1734-IJ

1 Channel 5V dc Encoder / Counter

1734-IK

1 Channel 15…24V dc Encoder / Counter

Configuration Data

Data Type

Default

Value

Valid Data Values

Counter Config

Config_0

SINT

BIT 0

BIT 1

BIT 2

BIT 3

0000=0=Counter

Config_1

Config_2

Config_3

0001=1=Encoder X1

0010=2=Encoder X2

0100=4=Encoder X4

0101=5=Period/Rate

0111=7=Rate Measurement

Mode_4

Mode_5

Mode_6

BIT 4

BIT 5

BIT 6

000=Store Count Disable

001=Store/Continue

010=Store/Wait/Resume

011=Store,Reset/Wait/Start

100=Store,Reset/Start

Z Input

BIT 7

0=Z Input Not Inverted

1=Z Input Is Inverted

Filter

SINT

BIT 0

BIT 1

BIT 2

BIT 3

120

(0x78H)

Filter_0

Filter_1

Filter_2

Filter_3

0000=No Filter

0001=50 kHz

0010=5 kHz

0100=500 Hz

1000=50 Hz

FilterA

FilterB

FilterZ

BIT 4

BIT 5

BIT 6

0=Input A/B/Z Not Filtered

1=Input A/B/Z Is Filtered

Decimal Position

SINT

Counter Config 0, 1, 2, 4:

-128…+127 (0…255)

Counter Config 5 & 7:

-4…+2

Time Base

(in 10 ms intervals)

INT

Counter Config 7 only:

0…3000 ms (10 ms…3 s)

Gate Interval

(Product of Time Base x Gate Interval

SINT

Counter Config 7 only:

-128…+127 (0…200)

must be ≤3000 ms)

Scalar

SINT

Counter Config 5 only:

-128…+127 (0…255)

0, 1, 2, 4, 8, 16, 32, 64, -128

Rollover

DINT

16,777,215 1…16,777,216

Preset (< Rollover)

0…16,777,215

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-30

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-IJ

1 Channel 5V dc Encoder / Counter

1734-IK

1 Channel 15…24V dc Encoder / Counter

Configuration Data

Data Type

Default

Value

Valid Data Values

SS Counter Control

SS Counter Reset

SINT

BIT 0

0=Count Unchanged

1=Count Cleared

SS Counter Preset

SS Value Reset

BIT 1

BIT 2

0=Count Unchanged

1=Count Set to Preset

0=Count Unchanged

1=Count Cleared

To enter values from +128 to +255, use these conversion formulas:

Decimal Position

Desired Decimal Position Value - 256 = Entered Decimal

Position Value.

As an example, for a divisor of 200, 200 - 256 = -56

Gate Interval

Desired Gate Interval Value - 256 = Entered Gate Interval Value.

As an example, for a Gate Interval of 200, 200 - 256 = -56

Scalar

Desired Scalar Value - 256 = Entered Scalar Value.

As an example, for a Scalar of 128, 128 - 256 = -128

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-31

1734-IJ

1 Channel 5V dc Encoder / Counter

1734-IK

1 Channel 15…24V dc Encoder / Counter

Input Data

Present Data

Stored Data

Data Type

Default Value

Valid Data Values

DINT

0…16,777,215

-2,147,483,648…

2,147,483,647

(0…4,294,967,295)

Status

INT

Zero Frequency Detected

BIT 1

0=No Fault

1=Fault Detected

Stored Data Count_2

Stored Data Count_3

BIT 2

BIT 3

Cycles through 0, 1, 2, 3, 0,

Increments after update

A Input Status

B Input Status

Z Input Status

BIT 4

BIT 5

BIT 6

0=Input A/B/Z is Off

1=Input A/B/Z is On

Not Ready

BIT 13

BIT 14

BIT 15

0=Module Ready

1=Module Initializing

EEPROM Fault

0=No Fault

1=EEPROM data bad

Program Fault

0=No Fault

(incomplete / incorrect / conflict)

1=Bad Configuration

(See Program Fault Note)

Stored Data

To interpret values from -2,147,483,648 to -1, use this conversion

formula:

Stored Data Tag Value + 4,294,967,296 = Actual Stored Data Tag

Value.

As an example, for a read value of -1,794,967,296:-1,794,967,296

+ 4,294,967,296 = 2,500,000,000 actual value

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-32

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

Program Fault Note

Programming Fault Error bit - If an incomplete, incorrect, or

conflicting set of configuration parameters is sent to the module, the

Program Fault bit is asserted and an error code placed in the

Programming Error Code word (assembly 6816). The module will not

enter a normal operational state. Bit definitions (decimal) for the error

codes are:

An invalid assembly was chosen for poll consumption (0, 105,

or 106 are valid).

The decimal point position is outside of the acceptable range.

Counter 0 window ON & OFF values are equal and not zero OR

Counter 0 window ON & OFF value is greater than the Rollover.

A tie has been connected to an unprogrammed window.

A configuration was selected that requires the scalar and none

was programmed OR

Multiple scalars were selected.

The preset is out of range (Rollover).

A rollover of zero was programmed through PWM was not

selected OR

A rollover was programmed and PWM was selected OR

Rollover is out of range (>0x01000000).

A configuration requiring a time base was selected and no gate

interval was set OR

Gate interval is out of range (>200) OR

Product of time base and gate interval is greater than 3 seconds.

A time base was entered that is not a multiple of 10 OR

Time base is out of range (>3000, or 3 seconds).

ZF/BF/AF were selected and no filter was programmed OR

Multiple filters were selected.

A reserved configuration/mode was programmed.

1734-IJ

1 Channel 5V dc Encoder / Counter

1734-IK

1 Channel 15…24V dc Encoder / Counter

Output Data

Data Type

Default Valid Data Values

Value

Counter Control

Counter Reset

SINT

BIT 0

0=Count Unchanged

1=Count Cleared

Counter Preset

BIT 1

BIT 2

0=Count Unchanged

1=Count Set to Preset

Value Reset

0=Count Unchanged

(Stored / Accumulated Count)

1=Count Cleared

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-33

1734-SSI

1 Channel Synchronous Serial Interface

Configuration Data

Data Type

SINT

Default Valid Data Values

Value

Run

0=Module Not Running

1=Module Is Running

Gray Binary

SINT

0=Binary Code

1=Gray Code

Word Length

Data Speed

SINT

2…31

5=125 Kbps

6=250 Kbps

7=500 Kbps

8=1 MB

9=2 MB

G2B Convert (Gray to Binary)

SINT

INT

0=No Convert

1=Convert

Standardization

(Divide / Shift using Trailing)

0=No Standardization

1=Apply Standardization

SSI Word Delay Time

-32,768…32,767 µs

(16…65,535)

Trailing (No. of Trailing Bits)

SINT

0…16

Input Latch Control

InputLatch_0

SINT

BIT 0

BIT 1

00=Off

01=Falling Edge of Input

10=Rising Edge of Input

11=Both Edges of Input

InputLatch_1

Sensor Resolution

(Positions per Rev. or Stroke)

INT

-32,768……32,767 counts

(1…65,535)

Sensor Cycle

(Total Revolutions or Strokes)

INT

-32,768…32,767 counts

(1…65,535)

Compare 0 Value

DINT

-2,147,483,648…

2,147,483,647

(0…4,294,967,295)

Compare 1 Value

DINT

-2,147,483,648…

2,147,483,647

(0…4,294,967,295)

Compare 0 Control

Compare0_0

SINT

BIT 0

BIT 1

00=Off

01=Up Direction

10=Down Direction

11=Both Directions

Compare0_1

Compare 1 Control;

Compare1_0

SINT

BIT 0

BIT 1

00=Off

01=Up Direction

10=Down Direction

11=Both Directions

Compare1_1

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-34

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

SSI Word Delay Time

To enter Delay values from +32,768 to +65,535 µs, use this conversion

formula:

Desired Delay Value (in µs) - 65536 = Entered Delay Value (in

µs).

As an example, for a 40 ms delay time, 40000 - 65536 = -25536

Sensor Resolution

To enter Resolution values from +32,768 to +65,535 µs, use this

conversion formula:

Desired Resolution Value - 65536 = Entered Resolution Value.

As an example, for a 40,000 count sensor, 40000 - 65536 =

-25536

Sensor Cycle

To enter Cycle values from +32,768 to +65,535, use this conversion

formula:

Desired Cycle Value - 65536 = Entered Cycle Value.

As an example, for 50,000 sensor cycle rotations, 50000 - 65536

= -15536

Compare 0,1 Value

To enter Compare values from +2,147,483,647 to +4,294,967,295, use

this conversion formula:

Desired Compare Value - 4,294,967,296 = Entered Compare

Value.

As an example, for a 3,000,000,000 compare value,

3,000,000,000 - 4,294,967,296 = -1,294,967,296

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-35

1734-SSI

1 Channel Synchronous Serial Interface

Input Data

Present Data

Latched Data

Data Type

Default Valid Data Values

Value

DINT

-2,147,483,648…2,147,483,647

(0…4,294,967,295)

DINT

-2,147,483,648…2,147,483,647

(0…4,294,967,295)

Status

INT

Input Status

BIT 0

0=Input is Off

1=Input is On

Run

BIT 1

BIT 2

BIT 3

0=Module is not Running

1=Module is Running

Decreasing Count

Increasing Count

0=Count not Decreasing

1=Count is Decreasing

0=Count not Increasing

1=Count is Increasing

Compare0 Reached

Compare1 Reached

BIT 4

BIT 5

0=Compare not Reached

1=Compare was Reached

Compare0 Status

Compare1 Status

BIT 6

BIT 7

0=Compare Off

1=Compare On

Power Fault

BIT 8

0=No 24Vdc Power Fault

1=24Vdc Power Fault

Configuration Fault

Communication Fault

Input Data Fault

Data Latched

BIT 9

0=No FPGA Config Fault

1=FPGA Config data bad

BIT 10

BIT 11

BIT 12

0=No FPGA Comm Fault

1=FPGA Comm Fault

0=No Input Data Fault

1=Input Power Fault (short)

0=Input Data Not Latched

1=Input Data Latched

Present / Latched Data

To interpret values from -2,147,483,648 to -1, use this conversion

formula:

Stored Data Tag Value + 4,294,967,296 = Actual Stored Data Tag

Value.

As an example, for a read value of -1,794,967,296:

-1,794,967,296 + 4,294,967,296 = 2,500,000,000 actual value

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-36

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-SSI

1 Channel Synchronous Serial Interface

Output Data

Data Type

Default Valid Data Values

Value

Control

SINT

BIT 0

Latch Acknowledge

0=Latch Not Cleared

1=Latch Cleared

Compare 0 Acknowledge

Compare 1 Acknowledge

Compare 0 Select

BIT 1

BIT 2

BIT 3

BIT 4

0=Compare0 Not Reset

1=Compare0 Reset

0=Compare1 Not Reset

1=Compare1 Reset

0=Compare0 Not Selected

1=Compare0 Selected

Compare 1 Select

0=Compare1 Not Selected

1=Compare1 Selected

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-37

1734-232ASC

1 Channel ASCII Interface Module

Configuration Data

Data Type

Default Valid Data Values

Value

Serial Character Format

(ASCII Format:

Data Bits / Parity / Stop)

SINT

0=7N2

1=7E1

2=7O1

3=8N1

4=8N2

5=8E1

6=8O1

7=7E2

8=7O2

Serial Comm Speed

(Communication Rate of the Serial Port)

SINT

0=9600 Kbps

1=1200 Kbps

2=2400 Kbps

3=4800 Kbps

4=19.2 KBps

5=38.4 KBps

Max Receive Characters

SINT

-128…+127 (0…128)

Receive Start Delimiter Mode

0=No Start Delimiter

1=Exclude Start Delimiter

2=Include Start Delimiter

Receive Start Delimiter Character

Receive Record End Mode

SINT

(0x3A)

Any Valid ASCII Character

(Default is Colon [:])

0=No End Delimiter

1=Exclude End Delimiter

2=Include End Delimiter

Receive End Delimiter

SINT

(0x0d)

Any Valid ASCII Character

(Default is Carr. Return)

Receive String Data Type

0=Array

1=Short String

2=String

Pad Mode

SINT

0=Pad Mode Disabled

1=Pad Mode Enabled

Pad Character

Receive Swap Mode

Any Valid ASCII Character

(Default is NULL)

(0x00)

0=Disabled

1=16-bit Swap Enabled

2=24-bit Swap Enabled

3=32-bit Swap Enabled

DeviceNet Handshake Mode

Max Transmit Characters

SINT

0=Master/Slave handshake

1=Produce Immediate

-128…+127 (0…128)

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-38

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

1734-232ASC

1 Channel ASCII Interface Module

Configuration Data

Data Type

Default Valid Data Values

Value

Transmit End Delimiter Mode

SINT

0=No End Delimiter

1=Exclude End Delimiter

2=Include End Delimiter

Transmit End Delimiter Character

Consume String Data Type

SINT

(0x0d)

Any Valid ASCII Character

(Default is Carr. Return)

0=Array

1=Short String

2=String

Transmit Swap Mode

SINT

0=Disabled

1=16-bit Swap Enabled

2=24-bit Swap Enabled

3=32-bit Swap Enabled

DeviceNet Record Header Mode

0=Transmit Handshake

1=Transmit Immediate

Transmit Data / Receive Data / Delimiter / Pad Character

Note that 7 data bits allows ASCII Character data values of 0 to 127,

which RSLogix 5000 software does support in the signed Short Integer

data type SINT (-128 to +127 range).

Note that 8 data bits allows ASCII Character data values of 0 to 255.

To enter values from +128 to +255, use this conversion formula:

Desired Decimal Value - 256 = Entered Decimal Value.

As an example, for an ASCII Character value of 128,

128 - 256 = -128

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

C-39

1734-232ASC

1 Channel ASCII Interface Module

Input Data

Data Type

Default Valid Data Values

Value

Receive Record Number

SINT

-128…+127 (0…255)

Status

TX FIFO Overflow

SINT

BIT 0

0=No Error

1=TX FIFO Overflow Error

RX FIFO Overflow

RX Parity Error

Handshake Error

New Data Flag

BIT 1

BIT 2

BIT 6

BIT 7

0=No Error

1=RX FIFO Overflow Error

0=No Error

1=RX Parity Overflow Error

0=No Error

1=Handshake Error

0=No New Data

1=New Data Present

Length_Lo

Length_Hi

Data[128]

SINT

-128…+127 (0…128)

0 or 1

Received ASCII Message

Output Data

Data Type

Default Valid Data Values

Value

Transmit Record Number

Receive Record Number

SINT

-128…+127 (0…255)

Status

TX FIFO Overflow

SINT

BIT 0

0=No Error

1=TX FIFO Overflow Error

RX FIFO Overflow

RX Parity Error

Handshake Error

New Data Flag

BIT 1

BIT 2

BIT 6

BIT 7

0=No Error

1=RX FIFO Overflow Error

0=No Error

1=RX Parity Overflow Error

0=No Error

1=Handshake Error

0=No New Data

1=New Data Present

Length_Lo

Length_Hi

Data[128]

SINT

-128…+127 (0…128)

0 or 1

Transmitted ASCII Message

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

C-40

1734 POINT I/O Module/RSLogix 5000 Controller Tag Reference

Transmit Record Number/ Receive Record Number / Length_Lo

Note that 7 data bits allows Transmit / Receive record Number of

Length_Lo values of 0 to 127, which RSLogix 5000 software does

support in the signed Short Integer data type SINT (-128 to +127

range).

Note that 8 data bits allows Transmit / Receive record Number of

Length_Lo values of 0 to 255.

To enter values from +128 to +255, use this conversion formula:

Desired Decimal Value - 256 = Entered Decimal Value.

As an example, for a Transmit / Receive record Number of

Length_Lo value of 128, 128 - 256 = -128

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Quick Start

In this quick start, you learn how to use the 1734-AENT adapter with a

ControlLogix controller for EtherNet/IP systems.

What This Appendix

Contains

This quick start contains a simple set of steps and

IMPORTANT

reminders that will help you avoid errors when you

are configuring your POINT I/O system for and

EtherNet/IP network.

You must use series C POINT I/O modules with

the 1734-AENT adapter. Series A or B POINT I/O

modules will not work with this adapter.

ATTENTION

Necessary Prerequisites

Before you begin this quick start, make sure the following conditions

are in place.

• The ControlLogix controller and RSLogix software version must

be version 11 or later.

• The 1756-ENBT module must be revision 2.3 or later.

• The 1734 POINT I/O modules must be series C (except for the

1734-232ASC modules, which can be series A).

• The recommended RPIs are being used: Digital = 10 ms or

higher, Analog and Specialty = 50 ms or higher.

• The 1734-AENT POINT I/O adapter is a child to a local

1756-ENBT module.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

D-2

Quick Start

In the 1734-AENT Module Properties dialog, perform the following

steps.

Configure the Adapter

1. Complete the Name field.

2. Enter the following address into the IP Address field:

192.168.1.42

You are setting the last digit, because the first three digits are set

for you as set by the push wheel switches on the adapter. The

push wheel switches should be set to 042.

3. From the Comm Format menu, choose None if you do not want

a rack-optimized connection, or choose Rack Optimization if

you want a rack-optimized connection.

4. For the Electronic Keying field, select Compatible Module.

5. Enter the Chassis Size.

Regarding chassis size, the POINT I/O adapter itself takes up a

count in the chassis. The default chassis size for the POINT I/O

is 1, which covers the adapter only and allows for no I/O. To

configure your POINTBus modules, set the chassis size to the

physical amount of your I/O modules plus one for the adapter;

otherwise, you get an error. For example, if you have six

modules in the chassis, you must set chassis to 6+1=7.

6. Enter the Slot.

For the adapter itself, the slot number is always 0 and cannot be

modified.

7. Click Finish.

Your I/O Configuration tree now looks similar to the following:

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Start

D-3

Enter Adapter Properties

Use this procedure to enter adapter properties.

1. Right-click the 1734-AENT adapter and select Properties.

The Module Properties dialog appears.

2. Click the Chassis Size tab.

Notice that the data under this tab is dimmed while offline. Use

the Chassis Size tab to send the module size from the General

tab to the module itself once you are online. Otherwise, you get

an error. We explore this later. For now, click OK to close this

dialog:

3. Right-click the POINT I/O adapter under I/O Configuration to

add a new module.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

D-4

Quick Start

4. Select the module from the list and click OK.

5. In the Module Properties dialog, enter the following information.

a. Name

b. Slot

c. Comm Format

d. Electronic Keying, choose Compatible Module to verify the

major revision C, because only series C modules support

EtherNet/IP.

e. Click Next on the bottom of the dialog.

f. Set the RPI to 10 ms for digital and 50 ms for analog or

specialty.

6. Click Finish.

Add Another Module Under the Adapter

Use this procedure to add another module under the adapter.

1. Right-click the POINT I/O adapter under I/O configuration to

add a new module.

Your second module is in slot 2.

2. Select the module from the Module Type list, and click OK.

3. In the Module Properties dialog, enter the following information:

a. Name

b. Slot

c. Comm Format

d. Electronic Keying, choose Compatible Module.

e. Click Next.

f. Set the RPI to 10 ms for digital and 50 ms for analog or

specialty.

4. Click Finish.

Continue to add modules to the adapter in this fashion until you

have added all of the POINT I/O modules connected to the

1734-AENT adapter to the I/O Configuration tree.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Start

D-5

For RSLogix 5000 software version 13 and earlier, configure your 1734

POINT I/O modules via the Controller Tags database, using the

following steps. For RSLogix 5000 software, versions 15 or later, the

preferred method for module configuration is to use the Module

Properties dialog for each POINT I/O module, as described in the

individual user manual for the module.

Configure 1734 POINT I/O

Modules

1. Double-click the Controller Tags in the project dialog.

Look at the bottom of the screen to make sure you are in the

Monitor Tags tab.

We are going to assume there is an analog input module

1734-IE2V, which resides in slot 6. We configure Channel 0 of

this module to operate over the range -10 to +10V dc.

2. Click the configuration tag remote_POINT_IO:3:C.

From here you can set the module’s configuration and alarms.

In this configuration dialog, you enter the values that would

correspond to the desired range. The range type default value

for a 1734-IE2V module is 2, which is equal to 0 to 10V dc.

3. Click the configuration tag for the module in slot 4,

remote_POINT_IO:3:Ch0RangeType.

4. Check the value in the tag

remote_POINT_IO:3:C.Ch0RangeType.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

D-6

Quick Start

It is set to 2, which is the default value. There are two settings

that this module supports:

• 2 = 0 to 10V dc

• 0 = -10 to +10V dc

5. Click the value 2 and change it to 0, which changes the voltage

range to -10 to +10V dc for channel 0.

Note the following:

• The controller sends the configuration data only when

connection is being established.

• Should you need to modify any of the tag values once you

change the tag, you need to access the updated information

and download it into the module. These are the ways to

download the updated configuration information into the

module.

– Ideally, you enter the correct code number in the Range Type

field at the same time that you add the I/O to the I/O

Configuration tree. You then download later.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Start

D-7

– If you downloaded the offline configuration into the module

and then realize that you must modify any of the module’s

configuration parameters, then the preferred way to make

these changes online is to go to the Module Connection tab

and inhibit the module, apply the changes, and then uninhibit

the module. Doing this breaks the connection, causing the

configuration information to be downloaded right after the

connection is made.

Switching the controller from Program to Run mode

IMPORTANT

does not change the module connection status and

does not re-send module configuration data.

We highly recommend that you use the

inhibit/uninhibit process and avoid power cycling.

6. Right-click the 1734-AENT adapter and select Properties.

7. Click the Connection tab.

You see the following message:

The module is faulted because, even though you set up the

adapters POINT I/O chassis size to the actual number of the

modules plus the adapter, the adapter still remembers the size of

1 (the factory default value) until you reset this size manually.

This option is available only online.

8. Click the Chassis Size tab.

9. Click the Set Chassis Size in Module button and set the chassis

size in the adapter.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

D-8

Quick Start

Remember to inhibit and unhibit the module for this to take

effect.

Now you can put your controller in Run mode, and the

connection should be successful.

The information found in the Controller Tag

Reference section of this user manual is also

IMPORTANT

available in the RSLogix 5000 online help file. Use

the Help file search function under the 1734 catalog

number that you are configuring and select the

Module Defined Data Types option. You see all of

the configurable parameters and associated values.

To configure an Ethernet driver in RSLinx software, launch RSLinx

software.

Configure an Ethernet

Driver in RSLinx Software

Launch RSLinx Software

Launching the RSLinx software enables you to configure the driver

you use to communicate with the ControlLogix controller.

1. Double-click the RSLinx icon on the Desktop to launch RSLinx

software.

2. Click the RSWho icon

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Start

D-9

The Rockwell Software RSLinx Gateway - [RSWho - 1] screen

appears.

The RSWho screen is actually RSLinx’s network

browser interface, which lets you view all of your

active network connections.

TIP

The left pane of this display is the Tree Control,

which shows networks and devices in a hierarchical

view. When a network or device is collapsed, as

indicated by the + sign, you can click the + sign or

double-click the network or device icon to expand

the view and begin browsing. When a network or

device is expanded, as indicated by the - sign, you

can click the - sign or double-click the network or

device icon to collapse the view. The right pane of

the RSWho display is the List Control, which is a

graphical representation of all of the devices present

on the network.

If there is a communication status error with a device

(for example, when a recognized device is

TIP

inadvertently unplugged), that device appears with a

red X, indicating that RSWho previously recognized

it, but now it cannot. You can choose to remove the

device from the RSWho display, or you can choose

to correct the communication error.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

D-10

Quick Start

Add the AB_ETHIP-1 (EtherNet/IP) Driver

1. From the Communications menu, choose Configure Drivers.

The Configure Drivers dialog appears.

2. From the Available Driver Types pull-down menu, choose

EtherNet/IP Driver.

3. Click the Add New button.

4. Click OK to accept the default name (AB_ETHIP-1).

5. Be sure that the radio button for Browse Local Subnet is

enabled.

6. Click OK.

7. Verify that the driver you just configured is running, and click

the Close button to exit the Configure Drivers dialog.

8. Click the X in the upper right corner of the RSWho dialog to

stop RSWho.

9. Click the minimize icon

in the upper right corner of the

RSLinx dialog to minimize RSLinx software.

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

Numerics

1734-POINT I/O catalog numbers C-1

data types

RSLogix 5000

valid number ranges C-2

DHCP (Dynamic Host Configuration

Protocol) 3-11

DHCP enabled function 3-2

DHCP software 3-11

direct connection 1-7

AB_ETH driver B-1

AB-ETHIP driver B-1

access module data 5-21

adapter

features 1-4

replacing on system 2-3

wiring 2-4

disabled web server function 3-2

auto negotiate 3-2

autobaud 1-8

edit controller tags 4-16

empty slots 1-2

empty terminal bases 1-3

example applications P-3

bandwidth, insufficient 4-24

BootP/DHCP utility 3-8

browse chassis page A-15

firmware revisions 1-5, 1-8

fixed IP address 4-22

catalog numbers C-1

chassis size 1-1

CIP Common Industrial Protocol 1-5

Common Industrial Protocol (CIP) 1-5

communication driver

RSLinx Ethernet B-1

gateway address 3-4

hardware 4-1, 5-2

compatibility

hardware and software 1-5

configuration 3-2

configure adapter

installing the 1734-AENT adapter

mount adapter to existing system 2-3

mounting on DIN rail before modules

installed 2-2

for direct connection and rack

optimization in RSLogix 5000

software 5-1

for direct connection in RSLogix 5000

software 4-1

replacing adapter 2-3

set the network address 2-3

wiring 2-4

IP address 3-3, 4-22

configure I/O modules 4-4, 5-4

controller tag reference

analog 2 channel input C-10

analog 2 channel output C-19

digital 2 POINT input C-3

digital 2 POINT output

ladder program 4-18

LED status indicators 6-1

with over load C-7

with over load & open load C-6

without diagnostics status C-5

digital 4 POINT input C-4

digital 4 POINT output

master/slave model 1-6

mix rack optimized and direct

connections 1-7

mount adapter to existing system 2-3

with over load C-9

with over load & open load C-8

specialty I/O C-23

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

mounting dimensions 2-5

mounting modules on DIN rail before

modules installed 2-2

RSLinx Ethernet communication driver

B-1

RSLinx software

install B-1

RSLogix 5000 data types

valid number ranges C-2

network address 2-3, 3-7

set chassis size 1-1

set the network address 2-3

software releases 1-5

subnet mask 3-5

overloaded adapter 4-24

power up system for the first time 1-4

producer/consumer model

understanding 1-6

terminology P-5

program fault note C-27, C-32

publications

third party DHCP server 3-1

thumbwheel 3-2, 3-7

troubleshooting 6-1

related P-4

quick start D-1

upgrades

hardware and firmware 1-5

utils directory 3-8

rack optimized connection 1-7

recover from an overloaded adapter

4-24

reinsertion of modules 1-2

relation list 3-10

verify module chassis size 4-20, 5-18

removal of modules 1-2

web page diagnostics A-1

Browse Chassis page A-15

Configuration page A-10

Diagnostics page A-3

replace adapter on system 2-3

replacement of adapter 1-2

requested packet interval (RPI) 1-6

RIUP remove and replace under power

1-2

Rockwell BootP/DHCP utility 3-8

RPI requested packet interval 1-6

Home page A-1

what the adapter does 1-5

wiring the adapter 2-4

Publication 1734-UM011C-EN-P - January 2006

Download from Www.Somanuals.com. All Manuals Search And Download.

How Are We Doing?

Your comments on our technical publications will help us serve you better in the future.

Thank you for taking the time to provide us feedback.

You can complete this form and mail (or fax) it back to us or email us at

RADocumentComments@ra.rockwell.com

Pub. Title/Type POINT I/O EtherNet/IP Adapter

Cat. No. 1734-AENT Pub. No. 1734-UM011C-EN-P

Pub. Date January 2006

Part No. 957988-75

Please complete the sections below. Where applicable, rank the feature (1=needs improvement, 2=satisfactory, and 3=outstanding).

Overall Usefulness

How can we make this publication more useful for you?

Can we add more information to help you?

Completeness

(all necessary information

is provided)

procedure/step

example

illustration

guideline

definition

feature

other

explanation

Technical Accuracy

(all provided information

is correct)

Can we be more accurate?

text

illustration

Clarity

How can we make things clearer?

(all provided information is

easy to understand)

Other Comments

You can add additional comments on the back of this form.

Your Name

Your Title/Function

Location/Phone

Would you like us to contact you regarding your comments?

___No, there is no need to contact me

___Yes, please call me

___Yes, please email me at _______________________

___Yes, please contact me via _____________________

Return this form to: Rockwell Automation Technical Communications, 1 Allen-Bradley Dr., Mayfield Hts., OH 44124-9705

Fax: 440-646-3525 Email: RADocumentComments@ra.rockwell.com

Publication CIG-CO521C-EN-P- May 2003

PN957782-91

Download from Www.Somanuals.com. All Manuals Search And Download.

PLEASE FASTEN HERE (DO NOT STAPLE)

Other Comments

PLEASE FOLD HERE

NO POSTAGE

NECESSARY

IF MAILED

IN THE

UNITED STATES

BUSINESS REPLY MAIL

FIRST-CLASS MAIL PERMIT NO. 18235 CLEVELAND OH

POSTAGE WILL BE PAID BY THE ADDRESSEE

Download from Www.Somanuals.com. All Manuals Search And Download.

Rockwell Automation provides technical information on the web to assist you

in using its products. At http://support.rockwellautomation.com, you can find

technical manuals, a knowledge base of FAQs, technical and application

notes, sample code and links to software service packs, and a MySupport

feature that you can customize to make the best use of these tools.

Rockwell Automation

Support

For an additional level of technical phone support for installation,

configuration and troubleshooting, we offer TechConnect Support programs.

For more information, contact your local distributor or Rockwell Automation

representative, or visit http://support.rockwellautomation.com.

Installation Assistance

If you experience a problem with a hardware module within the first 24

hours of installation, please review the information that's contained in this

manual. You can also contact a special Customer Support number for initial

help in getting your module up and running:

United States

1.440.646.3223

Monday – Friday, 8am – 5pm EST

Outside United

States

Please contact your local Rockwell Automation representative for any

technical support issues.

New Product Satisfaction Return

Rockwell tests all of its products to ensure that they are fully operational

when shipped from the manufacturing facility. However, if your product is

not functioning and needs to be returned:

United States

Contact your distributor. You must provide a Customer Support case

number (see phone number above to obtain one) to your distributor in

order to complete the return process.

Outside United

States

Please contact your local Rockwell Automation representative for

return procedure.

Publication 1734-UM011C-EN-P - January 2006 1

Supersedes Publication 1734-UM011B-EN-P -August 2005

PN 957988-75

Download from Www.Somanuals.com. All Manuals Search And Download.

Belkin Network Card F5D7001 User Manual
Belkin Switch F1DK102UUK User Manual
BenQ Projector MW851UST User Manual
Brinkmann Gas Grill ProSeries 4655 User Manual
Brother Automobile 810MC User Manual
Campbell Hausfeld Air Compressor FP2004 User Manual
Campbell Hausfeld Pressure Washer PW158010AV User Manual
Carrier Clothes Dryer 50K User Manual
Carrier Ventilation Hood HRVCCLHA User Manual
CDA Ventilation Hood CIGE9 User Manual