Casio Watch 1914 User Manual

Module No.1913/1914  
GENERAL GUIDE  
Press C to change from mode to mode.  
The watch automatically returns to the Timekeeping Mode if you do not perform any button operation for two or three minutes in any other mode.  
The animated display shows different animated characters and graphics, depending on the mode and the operation being performed.  
In any mode, press B to illuminate the display for about two seconds.  
Alarm Mode  
Countdown Alarm Mode  
Timekeeping Mode  
Animated display  
Stopwatch Mode  
The operational procedures for Module  
1913 and 1914 are identical. All of the  
illustrations in this manual show Mod-  
ule 1913.  
[Module 1913]  
[Module 1914]  
TIMEKEEPING MODE  
COUNTDOWN ALARM MODE  
Animated Display  
Current time  
In the Timekeeping Mode, press D to switch between  
the 12-hour and 24-hour formats. With the 12-hour  
format, the animated display shows repeating charac-  
ters that indicate the current day of the week. With the  
24-hour format, it shows a G-mark.  
The countdown timer can be set within a range of 1  
minute to 60 minutes. When the countdown reaches  
zero, an alarm sounds for 10 seconds or until you press  
any button.  
Color mark  
Month  
Day  
To set the countdown time  
To set the time and date  
1. Hold down A while in the Countdown Alarm Mode.  
The minutes digit flashes on the display because it is  
selected.  
1. Hold down A while in the Timekeeping Mode. The  
seconds digits flash on the display because they are  
selected.  
Minutes  
2. Press D to increase the selected number. Holding  
down D changes the selection at high speed.  
3. After you set the countdown time, press A to return  
to the Countdown Alarm Mode.  
If you do not operate any button for a few minutes  
while a selection is flashing, the flashing stops and the  
watch goes back to the Countdown Alarm Mode auto-  
matically.  
2. Press C to change the selection in the following se-  
quence.  
Seconds  
Minutes  
Hour Seconds  
PM indicator  
Seconds  
Day  
Hour  
Minutes  
Year  
Month  
3. While the seconds digits are selected (flashing), press D to reset the seconds to  
“00”. If you press D while the seconds count is in the range of 30 to 59, the  
seconds are reset to “00” and 1 is added to the minutes. If the seconds count is  
in the range of 00 to 29, the minutes count is unchanged.  
4. While any other digits (besides seconds) are selected (flashing), press D to  
increase the number. Holding down D changes the current selection at high  
speed.  
To use the countdown timer  
1. Press D while in the Countdown Alarm Mode to start the countdown timer.  
2. Press D again to stop the countdown timer.  
You can continue countdown timer operation by pressing D.  
3. Stop the timer and then press A to reset the countdown time to its starting  
value.  
When the countdown reaches zero, an alarm sounds for 10 seconds or until you  
stop the alarm by pressing any button. The countdown time is automatically reset  
to its starting value after the alarm stops.  
5. After you set the time and date, press A to return to the Timekeeping Mode.  
The day of the week is automatically set in accordance with the date.  
The date can be set within the range of January 1, 1995 to December 31, 2039.  
If you do not operate any button for a few minutes while a selection is flashing,  
the flashing stops and the watch goes back to the Timekeeping Mode automati-  
cally.  
About countdown indicators  
An audible beep, the EL backlight, and the color marks on the display keep you  
informed about the progress of the countdown as noted in the following table.  
Color mark  
(Module 1913 Only)  
Remaining  
Start (pressing D)  
5'00"  
Audible beep  
1 second  
EL Backlight  
1 second  
ALARM MODE  
When the Daily Alarm is switched on, the alarm sounds  
for 20 seconds at the preset time each day. Press any  
button to stop the alarm after it starts to sound.  
When the Hourly Time Signal is switched on, the watch  
beeps every hour on the hour.  
Current time  
AM indicator  
1 second  
1 second  
Time up (00'00")  
10 seconds  
2 seconds  
To set the alarm time  
When the starting value is five minutes or less, the color marks start from center.  
1. Hold down A while in the Alarm Mode. The hour  
digits flash on the display because they are selected.  
At this time the Daily Alarm is switched on automati-  
cally.  
Hour  
Minutes  
2. Press C to change the selection in the following se-  
quence.  
Hourly time  
signal on  
indicator  
STOPWATCH MODE  
Alarm on  
indicator  
Hours  
The Stopwatch Mode lets you measure elapsed time,  
split times, and two finishes. The range of the stop-  
watch is 23 hours, 59 minutes, 59.99 seconds.  
Hour  
Minutes  
3. Press D to increase the selected digits. Holding down D changes the selection  
at high speed.  
The format (12-hour and 24-hour) of the alarm time matches the format you  
select for normal timekeeping.  
When setting the alarm time using the 12-hour format, take care to set the time  
correctly as morning (A) or afternoon (P).  
4. After you set the alarm time, press A to return to the Alarm Mode.  
If you do not operate any button for a few minutes while a selection is flashing,  
the flashing stops and the watch goes back to the Alarm Mode automatically.  
To measure elapsed time  
1. Press D to start the stopwatch.  
2. Press D to stop the stopwatch.  
You can resume the measurement operation by press-  
ing D again.  
Minutes  
Seconds  
1/100 second  
3. Press A to clear the stopwatch to all zeros.  
To record split times  
1. Press D to start the stopwatch.  
2. Press A to display the timing up to that point. Stop-  
watch timing continues internally.  
To switch the Daily Alarm and Hourly Time Signal on and off  
Press D while in the Alarm Mode to change the status of the Daily Alarm and  
Hourly Time Signal in the following sequence.  
3. Press A to clear the split time and to continue time measurement on the display.  
You can repeat steps 2 and 3 as many times as you want.  
4. Press D to stop the time measurement.  
[Alarm ON Indicator/Hourly Time Signal ON Indicator]  
5. Press A to clear the stopwatch to all zeros.  
Both ON  
Both OFF  
Daily Alarm only  
Hourly Time  
Signal only  
To time first and second place finishes  
1. Press D to start the stopwatch.  
2. Press A when the first finisher crossed the line, and record the time.  
3. Press D when the second finisher cross the line.  
4. Press A to display the finishing time of the second finisher.  
5. Press A again to clear the stopwatch to all zeros.  
To test the alarm  
Hold down D while in the Alarm Mode to sound the alarm.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Billy Goat Lawn Mower SV50 User Manual
Bionaire Humidifier BCM 3600 User Manual
Black Decker Work Light 90518422 User Manual
Blaupunkt Car Stereo System Toronto RDM 128 User Manual
Bosch Appliances DVD Player Divar Digital Versatile Recorder User Manual
Braun Electric Shaver BS 8985 User Manual
Briggs Stratton Lawn Mower Accessory 500Z 26 User Manual
Campbell Hausfeld Pressure Washer PW1350 User Manual
Canon Camera Lens 2540A002 User Manual
CFM Fan AeroFan User Manual