Casio Projector XJA141 User Manual

E
DATA PROJECTOR  
XJ-A141/XJ-A146*  
XJ-A241/XJ-A246*  
XJ-A251/XJ-A256*  
* USB Port Models  
User’s Guide  
z Be sure to read the precautions in the separate Setup Guide.  
z Be sure to keep all user documentation handy for future  
reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Connecting the Analog RGB Output of a  
Connecting the HDMI Output of a Video Device or  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Projector Overview  
This section describes the features of the projector, and explains the functions of the projector and  
remote controller keys.  
Projector Features and Main Functions  
XJ-A141/XJ-A146/XJ-A241/XJ-A246/XJ-A251/XJ-A256  
z Mercury-free Hybrid Light Source:  
A CASIO-original laser and LED hybrid light source delivers high luminance from 2,500 to  
3,000 lumens. This projector does not use a mercury lamp, making it environmentally friendly.  
z Slim and compact:  
A4 file size and approximately 43 mm slim. Compact enough to install or use just about anywhere.  
z HDMI video/audio input:  
HDMI (High Definition Multimedia Interface) input support enables direct connectivity with today’s  
HDMI enabled notebook PCs, high-definition video devices (BD, HD DVD, DVD players, etc.), and  
games. The projector supports image projection and audio output from these devices.  
z Wide projection range:  
A wide angle 2X zoom allows projection even when projector-to-screen distance is severely limited.  
When using a projection size of 60 inches, projection can be performed from a distance of  
1.4 meters (XJ-A241/XJ-A246/XJ-A251/XJ-A256) or 1.7 meters (XJ-A141/XJ-A146).  
z A wide selection of input sources:  
Analog RGB, composite video, component video (Y·Cb·Cr, Y·Pb·Pr), and HDMI input sources are  
supported.  
z Intelligent Brightness Control function (Eco Mode):  
The projector senses surrounding light levels and adjusts projection brightness automatically as  
required for efficient low-power operation. (Requires “Eco Mode” setting to be set to “On (Auto)”.)  
z Pointer:  
The remote controller can be used to select one of a variety of different pointers for use during  
projection.  
z Direct Power On:  
The projector can be configured to turn on automatically and start projecting as soon as it is  
plugged into a power outlet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
   
XJ-A241/XJ-A246/XJ-A251/XJ-A256  
z WXGA Resolution:  
The XJ-A241/XJ-A246/XJ-A251/XJ-A256 models support WXGA (1280 × 800) resolution for optimal  
viewing of content formatted for today’s widescreen displays. This makes it perfect for projecting  
images from widescreen notebook PCs and HD video input sources.  
XJ-A146/XJ-A246/XJ-A256  
z Projection of Data from USB Memory or a Memory Card without a Computer:  
USB memory or a memory card (using a commercially available USB card reader) can be connected  
directly to the projector’s USB port. The projector comes with special software for converting  
PowerPoint presentation data to a format that can be stored to USB memory or a memory card and  
projected without using a computer. Images and movies also can be projected directly from USB  
memory or a memory card.  
z Multi Projection Camera (YC-400, YC-430) Connection:  
A CASIO Multi Projection Camera can be connected directly to the projector’s USB port for fine  
resolution projection of documents and other images. Document camera capabilities allow  
projection of data without going through a computer.  
z Graphic Scientific Function Calculator Connection:  
Certain CASIO graphic scientific calculator models can be connected directly to the projector’s  
USB port for projection of the calculator screen contents.  
z Projection of Computer Screen Contents via Wireless LAN:  
The projector comes with a wireless LAN adapter. After a wireless LAN connection is established,  
the contents of the computer screen can be sent to the projector for projection.  
z Support for Wireless projection from MobiShow:  
You can install AWIND’s MobiShow (client software for wireless connection to a projector) on a  
smartphone or mobile terminal, and then use the projector to project photographs and presentation  
files stored in the smartphone or terminal memory.  
* Note that the type of terminal and the MobiShow version can limit certain functions or can even  
make projection impossible.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Remote Controller and Projector Keys  
Operations in this manual are presented based on the remote controller that comes with the projector.  
Major operation keys are also provided on the projector unit, so the most of the same procedures can  
also be performed directly on the projector.  
Remote Controller Keys  
[INPUT] key  
[MENU] key  
Remote control signal emitter  
[ZOOM +] [ZOOM –] keys  
CLASS 1 LED PRODUCT  
[FOCUS S] [FOCUS T] keys  
[P] (Power) key  
[TIMER] key  
[ESC] key  
Cursor keys (S/T/W/X)  
[ENTER] key ([STYLE] key)  
[FUNC] key  
[AUTO] key  
[BLANK] key  
[D-ZOOM +] [D-ZOOM –] keys  
[KEYSTONE +] [KEYSTONE –] keys  
[POINTER] key  
[FREEZE] key  
[COLOR MODE] key  
[VOLUME] key  
[BRIGHT] key ([O] key)  
[ECO] key ([f] key)  
[ASPECT] key ([Z] key)  
The remote controller does not come with batteries loaded. You need to load the two supplied  
batteries before use.  
Important!  
To avoid running down the batteries, store the remote control unit so its keys are not pressed  
inadvertently.  
Projector Keys and Indicators  
TEMP indicator  
LIGHT indicator  
POWER/STANDBY indicator  
[FOCUS] key  
[ENTER] key  
[MENU] key  
[ESC] key  
[P] (Power) key  
[INPUT] key  
[AUTO] key  
Cursor keys (q/w/U/I)  
[ZOOM] key  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
 
Back Terminals  
Depending on your projector, the orientation of the ports and terminals may be opposite from those  
shown in the illustration below. Functions and use of the ports and terminals are the same as  
described in this manual, regardless of their orientation.  
COMPUTER terminal  
Serial port*  
AV terminal  
Speaker  
Remote control signal receiver  
HDMI port  
Intake vents  
USB port  
Power connector  
(XJ-A146/XJ-A246/XJ-A256 only)  
Anti-theft lock hole  
* This serial port is for connecting a separately available special cable (YK-5) to control the projector  
from a computer.  
Loading Remote Controller Batteries  
Important!  
Be sure to use alkaline batteries only.  
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.  
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.  
Caution  
*
1. Open the battery cover on the back 2. Load two new batteries into the  
of the remote controller.  
case, making sure that their positive  
(+) and negative (–) ends are facing  
correctly.  
3. Close the battery cover on the back of the remote controller.  
Replacing Remote Controller Batteries  
Open the battery cover on the back of the remote controller, replace the old batteries with new ones,  
and then close the battery cover.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C
9
   
Setting Up the Projector  
Locate the projector on a desk, table, or stand that is firm and level. Make sure that you allow  
sufficient space around the sides and back of the projector for proper ventilation. The following  
illustrations show how the projector should be oriented for optimum projection relative to the screen.  
XJ-A141/XJ-A146  
XJ-A241/XJ-A246/XJ-A251/XJ-A256  
Screen  
Screen  
Make sure the projector is at a right angle to the screen.  
Position the projector so the lens side is at the edge of the table,  
etc.  
z The projector can be configured for projection from the back of a screen. For details, see  
Setup Precautions  
z Use a conveniently located power outlet that you can reach easily when you need to unplug the  
projector.  
z Do not allow any objects to be within the area indicated by the dashed line below, which is an area  
within 30cm (11.8 inches) of the projector. Keep all obstacles and other objects at least 30cm away  
from the projector’s vents.  
z Airflow from air conditioning equipment can blow the heat being exhausted from the area around  
the projector’s lens in a way that causes heat ripples to appear in the projected image. If this  
happens, adjust the airflow of the air conditioning equipment or move the projector.  
Intake vents  
Intake vents  
Exhaust vents  
30cm  
(11.8 inches)  
Intake vents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
     
Connecting to an Image Output Device  
Connecting the Analog RGB Output of a Computer to  
the Projector  
Connect the projector’s COMPUTER terminal to the RGB terminal of a computer as shown in the  
illustration below.  
Important!  
z Always turn off the projector and the computer before connecting them.  
z Take care so the volume level of the computer is not set too high.  
Projector  
Computer  
AV terminal  
COMPUTER terminal  
To monitor terminal  
To line output terminal  
(analog RGB output terminal)  
Bundled mini D-Sub cable  
Audio cable (commercially available)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
     
Connecting the HDMI Output of a Video Device or  
Computer to the Projector  
The projector supports projection and output of HDMI video and audio output from a computer or  
video device.  
Important!  
Turn off the projector and the computer or video device before connecting them.  
Projector  
Computer or video device  
HDMI port  
To HDMI output terminal  
HDMI cable (commercially available)  
z You will need to obtain a commercially available HDMI cable with a connector that matches the  
terminal of the output device on one end and a connector that matches the projector’s HDMI port  
(HDMI Type A Socket) on the other end.  
z For information about HDMI video signal supported by the projector, see page 54.  
z The projector supports L-PCM 32kHz, 44.1kHz, and 48kHz HDMI audio signals.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
 
Connecting to a Video Device  
The projector is able to project images from the composite video output or component video output of  
a connected video device.  
Important!  
Always turn off the projector and the video device before connecting them.  
Connection to a composite video output  
Projector  
Video device  
AV terminal  
To video output  
To audio output  
terminals  
terminal  
Yellow  
Red  
White  
Bundled special AV cable  
z You can use the bundled special AV cable to connect to a pin jack (RCA) type video output terminal.  
When connecting a video camera or other video device with a special video output terminal, use the  
special cable that comes with the video device. For details, see the documentation that comes with  
the video device.  
Connection to a component video output  
Projector  
Video device  
AV terminal  
COMPUTER terminal  
To component video  
output terminals  
To audio output  
terminals  
Yellow  
(Not connected)  
Red  
Component video cable (commercially available)  
White  
Bundled special AV cable  
z Component video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to match  
the colors of the plugs on a component video cable with the colors of the terminals (Green: Y;  
Blue: Cb/Pb; Red: Cr/Pr).  
z Note that connection only to an analog component video output terminal is supported.  
Connection to a digital output terminal is not supported.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
       
Operation During Projection  
Selecting the Input Source  
Turning on the projector initially causes the same input source that was selected the last time it was  
turned off to be selected.  
To select a different input source  
1. Press the [INPUT] key.  
z This displays the input source selection screen.  
2. Use the [T] and [S] keys to select the name of the input source you want to  
select and then press the [ENTER] key.  
z The name of the input source you select appears in the upper right corner of the projection  
screen for a few seconds.  
z The message “No signal input.” will appear if no input signal can be selected.  
Resolution  
Depending on the projector model, its video resolution will be fixed at XGA (1024 × 768 pixels) or  
WXGA (1280 × 800 pixels). Images may appear coarse, text and other figures may be difficult to read  
or a moire pattern may appear when the input signal from a computer does not match the projector’s  
video resolution. If this happens, try doing the following.  
z Change the computer’s output resolution setting so it matches the projector’s video resolution.  
For information about the video resolution of your projector, see the “DLP chip” item of the  
Specifications” (page 55). See the user documentation that comes with your computer for details  
about changing its settings.  
z Change the “Aspect Ratio” setting to “True” (Applies only to models that support WXGA video  
resolution).  
With the “True” setting, the projector projects the input signal at its actual size (1 input source dot  
equal to one projector output pixel dot).  
For information about configuring the Aspect Ratio setting, see “Changing the Aspect Ratio of the  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
       
Image Operations During Projection  
You can perform the following operations while projecting an image.  
z Image brightness adjustment  
z Manual keystone correction  
z Color mode selection  
z Image zooming  
z Momentarily blanking the image and muting the audio  
z Image freeze  
z Pointer display in the projected image  
z Aspect ratio switching  
Adjusting Image Brightness  
Note  
(for USB port model users)  
Use the setup menu (page 25) to adjust image brightness when the input source is an external  
device connected to the USB port or via the wireless adapter.  
1. Press the [BRIGHT] key.  
z This displays the brightness adjustment window.  
2. Use the [W] and [X] keys to adjust image brightness.  
3. To hide the window, press the [ESC] key.  
To use manual keystone correction  
The projector has a keystone correction feature that prevents  
distortion of the projected image when projecting from an  
angle. The projector detects when it is at a vertical angle to the  
screen and performs keystone correction automatically.  
You can use the [KEYSTONE +] and [KEYSTONE –] keys to  
adjust keystone correction manually.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
15  
     
Selecting the Color Mode  
You can select from among various different color mode settings in accordance with image contents  
and projection conditions.  
Important!  
The color mode cannot be selected in the following cases.  
z When “Off” is selected for the Eco Mode setting (page 23)  
To change the color mode  
1. Press the [COLOR MODE] key.  
z This displays the color mode selection window. The currently selected color mode is the one  
whose button is selected (filled in).  
2. Use the [T] and [S] keys to move the highlighting to the color mode you want to  
select, and then press the [ENTER] key.  
z This will select the button next to the highlighted color mode name.  
z For details on what each color mode does, see “Color Mode” (page 34) under “Image  
3. To hide the window, press the [ESC] key.  
Zooming an Image  
1. Press the [D-ZOOM +] key.  
z This will enlarge the center of the projected image one step.  
2. To zoom in on the center of the projected image more, press the [D-ZOOM +]  
key again. To zoom out, press the [D-ZOOM –] key.  
z Each press of [D-ZOOM +] zooms in (increases the zoom factor), while [D-ZOOM –] zooms  
out. Holding down either key continuously scrolls the zoom factor.  
3. While an image is zoomed, use the [S], [T], [W], and [X] keys to scroll the view  
to other parts of the image.  
4. To exit the zoom operation, press the [ESC] key.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
   
Momentarily Blanking the Image and Muting the Audio  
1. Press the [BLANK] key.  
z This temporarily blanks the image (projecting a black screen) and mutes the audio.  
2. To resume normal image and sound, press the [BLANK] key (or [ESC] key).  
Note  
You can specify projection of a black screen or blue screen, or a logo. For details, see “Blank  
Freezing an Image  
Pressing the [FREEZE] key freezes the projected image.  
To freeze the projected image  
1. While an image is being projected from an input source, press the [FREEZE] key.  
z This will capture the image that is on the screen at the moment you press [FREEZE] and stores  
it in projector memory. That image remains projected on the screen.  
2. To restore projection of the image from an input source, press the [ESC] key.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
17  
   
Displaying a Pointer in the Projected Image  
You can select from among different pointer styles, including various arrow styles, for display in the  
projected image. Pointers can be used during a presentation to indicate or highlight a specific part of  
the image.  
Note  
Depending on the pointer style you are using, the pointer may not display properly when you are  
using keystone correction. If this happens, use the [KEYSTONE +] and [KEYSTONE –] keys to  
change the keystone correction value to zero.  
To display a pointer in the image  
1. Press the [POINTER] key.  
z This will cause a pointer to appear in the image.  
z You also can use the setup menu to specify the pointer type that appears first when you press  
the [POINTER] key. For details, see “Pointer” (page 40) under “Option Settings 2 Main Menu”.  
2. Use the cursor keys to move the pointer to the location you want.  
z Holding down a cursor key moves the cursor at high speed.  
3. To modify the pointer as described below, press the [STYLE] key.  
For this pointer type:  
Pressing [STYLE] will change it like this:  
J
J
J
J
J
J
J
J
J
J
J
J
Toggle between flashing and not flashing  
To select the pointer type  
1. Press the [POINTER] key to display the pointer.  
2. Keep pressing the [POINTER] key until the pointer you want is displayed.  
z Each press of the [POINTER] key cycles through the available pointer types.  
To clear the pointer from the image  
Press the [ESC] key.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
 
Changing the Aspect Ratio of the Projected Image  
Press the [ASPECT] key to cycle through the aspect ratio settings for the projected image.  
Available settings depend on your projector model as shown below. For details about the meaning of  
XJ-A241/XJ-A246/XJ-A251/XJ-A256  
Pressing the [ASPECT] key will cycle through settings in accordance with the current input source as  
shown below.  
Input Source  
Video, Component, HDMI (DTV)  
RGB, HDMI (PC)  
Pressing [ASPECT] will cycle through these settings:  
Normal J 16:9 J 4:3 J Letter Box  
Normal J Full J 4:3 J True  
XJ-A141/XJ-A146  
Pressing the [ASPECT] key will toggle between settings in accordance with the current input source as  
shown below.  
Input Source  
Video, Component, HDMI (DTV)  
RGB, HDMI (PC)  
Pressing [ASPECT] will toggle between these settings:  
Normal  
Normal  
16:9  
Full  
Note  
z For details about how the aspect ratio setting affects the projected image, see “Aspect Ratio  
z You also can change the aspect ratio setting using the setup menu. For details, see “Aspect  
Important!  
Note that enlarging or reducing the size of an image using the [ASPECT] key for commercial  
purposes or public presentation may infringe on the legally protected copyright of the copyright  
holder of the original material.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
19  
 
Adjusting the Volume Level  
You can use the remote controller keys to adjust the volume level of the audio that is output from the  
projector’s speaker or the AV terminal.  
To adjust the volume level  
1. Press the [VOLUME] key.  
z This causes the [Volume] screen to appear on the projected image.  
2. Press the [X] key to increase the volume, or the [W] key to lower the volume.  
3. After the setting is the way you want, press the [ESC] key.  
z This causes the [Volume] screen to disappear.  
Note  
You also can use the setup menu to adjust the volume level. For details, see “Volume  
To mute the audio  
1. Press the [VOLUME] key.  
2. Press the [ENTER] key.  
z This stops output from the speaker.  
3. To restore the audio, press the [VOLUME] key again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
20  
       
Presentation Timer  
The presentation timer shows the amount of presentation timing remaining. You can configure the  
presentation times so it is displayed in the projected image.  
Timer  
To specify timer display position and countdown time settings  
1. Press the [TIMER] key.  
z This will cause the timer to appear in the projected image. The initial default display position is  
the lower right corner of the image.  
2. While the timer is displayed, press the [TIMER] key again.  
z This will cause the timer to disappear and the timer function menu to appear.  
3. Use the [T] key to select “Position”.  
4. Use the [W] and [X] keys to change the setting to the display position you want.  
z Available settings are Lower Right, Upper Right, Upper Left, and Lower Left. The initial default  
position is Lower Right.  
5. Use the [T] key to select “Start Time”.  
6. Use the [W] and [X] keys to change the setting to the countdown start time you want.  
z You can set a start time from five to 60 minutes, in five-minute steps. The initial default setting  
is 20 minutes.  
7. After the settings are the way you want, press the [ESC] key.  
z This will cause the timer function menu to disappear. The timer will appear in the projected  
image for about five seconds and then disappear (under initial settings).  
z If you want the timer to remain displayed without disappearing, change the “Continuous  
Display” setting to “On”.  
z Even if “Continuous Display” is “On”, you can clear the timer from the image at any time by  
pressing [ESC]. The timer will also disappear when you display a menu or a dialog box. To  
re-display the timer after it has disappeared, press [TIMER].  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
21  
   
To start a countdown timer operation  
1. Press the [TIMER] key to display the timer function menu.  
z If necessary, use the procedure under “To specify timer display position and countdown time  
settings” (page 21) to configure timer display position and start time settings.  
2. Use the [T] and [S] keys to select “Start Timer” and then press the [ENTER] key.  
z This will close the timer function menu and start the countdown.  
z The timer will be displayed at this time. If the timer function menu “Continuous Display” item is  
“Off”, the timer will disappear after about five seconds. If “On”, the timer will remain displayed.  
To re-display the timer after it has disappeared, press [TIMER].  
z After the countdown reaches 00:00, it will start a count up operation (from –00:01 to –60:00).  
The numerals of the timer display are red during a count up operation.  
Note  
z If the timer is not displayed, it will appear automatically for about five seconds when the  
countdown time reaches 3, 2, 1, and 0 minutes. If the timer function menu “Continuous  
Display” item is “Off”, the timer will disappear after about five seconds. If “On”, the timer will  
remain displayed.  
z Turning off the projector, performing the “Restore All Defaults” (page 42) operation, or  
performing the “Restore Menu Defaults” (page 41) operation on the Option Settings 2 main  
menu while a timer countdown operation is in progress will stop the countdown and return the  
countdown start time to the “Start Time” setting. Any other projector operations do not have  
any affect on the timer.  
To pause the timer countdown  
1. While a timer countdown is in progress, press the [TIMER] key to display the  
timer function menu.  
2. Make sure that “Pause Timer” is selected and then press the [ENTER] key.  
z This will pause the countdown and cause the timer function menu to disappear.  
To restart a paused timer countdown  
1. While the timer countdown is paused, press the [TIMER] key to display the timer  
function menu.  
2. Make sure that “Restart Timer” is selected and then press the [ENTER] key.  
z This will restart the countdown and cause the timer function menu to disappear.  
To reset the timer to its start time  
1. Press the [TIMER] key to display the timer function menu.  
2. Use the [T] key to select “Reset Timer” and then press the [ENTER] key.  
z This will return the timer to the start time specified by “Start Time” and cause the timer  
function menu to disappear.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
22  
Eco Mode (Power Saving, Low Noise)  
The following three Eco Mode settings are available to specify whether priority should be given to  
low-power, low-noise operation or to projection brightness.  
On (Auto) : A brightness sensor on the top of the projector senses surrounding light, and  
automatically adjusts projection brightness and color accordingly. Brightness is  
reduced for darker surroundings, which saves power and reduces operation noise.  
On (Manual): Enables manual adjustment to balance the needs of low-power, quiet operation and  
projection brightness.  
Off  
: Give top priority to projection brightness.  
Important!  
z While “On (Auto)” is selected as the Eco Mode setting, make sure that the brightness sensor  
on the top of the projector is not blocked by anything.  
z The local environment and setup conditions affect the brightness sensor, so operation when  
“On (Auto)” is selected for the Eco Mode depends on these factors.  
To select the Eco Mode  
1. Press the [ECO] key.  
z This causes “Eco Mode” window to appear on the projection screen.  
2. Use the [W] and [X] keys to select the setting you want.  
z If you select “On (Manual)” here, go to step 3. If you select another setting, jump to step 4.  
3. Perform the following steps to adjust the “Eco Level” (the balance between  
low-power, quiet operation and projection brightness).  
1 Press the [T] key to move the highlighting to the Eco Level.  
2 Use the [W] and [X] keys to adjust the Eco Level to the setting you want.  
Fewer  
marks gives higher priority to projection brightness. A greater number gives high  
priority to low-power, quiet operation.  
4. To hide the window, press the [ESC] key.  
Important!  
The “On (Auto)” setting cannot be selected for the Eco Mode while “Rear” is selected for “Screen  
Settings Projection Mode” (page 37) on the setup menu. If the “Projection Mode” setting is  
J
changed to “Rear” while “On (Auto)” is selected for the Eco Mode setting, the Eco Mode setting  
will automatically change to “On (Manual)”.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
     
Note  
z While “Off” is selected for the Eco Mode setting, you also can specify whether brightness or  
color should be given emphasis. For details, see “Eco Off Mode” (page 34) under “Image  
z (for USB port model users)  
Use the setup menu (page 25) to select the Eco Mode when the input source is an external  
device connected to the USB port or via the wireless adapter.  
Using the [FUNC] Key  
Pressing the [FUNC] key displays the menu shown below.  
You can use this menu to perform the operations described below.  
z Adjust image brightness  
Highlight “Brightness” and then press the [ENTER] key.  
J This performs the same operation as pressing the [BRIGHT] key (O key) described on page 15.  
z Turn the Eco Mode on or off  
Highlight “Eco Mode” and then press the [ENTER] key.  
J This performs the same operation as pressing the [ECO] key (  
f
z Select the aspect ratio of the projected image  
Highlight “Aspect Ratio” and then press the [ENTER] key.  
J This performs the same operation as pressing the [ASPECT] key ( key) described on page 19.  
Z
Note  
(for USB port model users)  
When the input source is an external device connected to the USB port or via the wireless  
adapter, use the [FUNC], [O], [ ], and [ ] keys to control the connected device. For details,  
f
Z
see the “USB Function Guide” and “Wireless Function Guide” on the bundled CD-ROM.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
 
Configuring Advanced Projector Settings  
Your projector has a setup menu that you can use to configure advanced settings.  
Basic Setup Menu Operations  
Displaying the Setup Menu  
Pressing the [MENU] key displays the menu shown below in the center of the projection screen.  
Main menu  
Pressing the [MENU] key displays the main menu.  
The currently selected menu item is the one that is  
highlighted.  
Sub-menu  
The sub-menu shows each individual setting under each  
main menu item, and its current setting.  
Guidance text  
Guidance text provides a brief description of the main  
key operations available for the operation you are  
currently performing.  
To exit the setup menu  
Press the [MENU] key.  
Configuring Setup Menu Settings  
1. Press the [MENU] key to display the setup menu.  
2. Use the [T] and [S] keys to select the main menu item you want by highlighting  
it.  
3. Press the [ENTER] key.  
4. Use the [T] and [S] keys to select the sub-menu item you want by highlighting it.  
5. Perform the required operation on the selected sub-menu item screen.  
z The guidance text explains the operations you need to perform to configure each setting.  
6. To return to the main menu from the sub-menu, press the [ESC] key.  
7. To exit the setup menu, press the [MENU] key.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
       
Basic Setup Menu Example  
The procedure below shows how to configure the following three settings:  
z Image Adjustment 1 J Contrast  
z Image Adjustment 1 J Color Mode  
z Input Settings J Signal Name Indicator  
Note  
z The setup menu items that you can change depend on whether or not an image signal is being  
input to the projector, and on the currently selected input source. Perform the procedure  
below after starting projection of an image from an input source.  
z This example covers basic steps only. For more detailed information, see “Setup Menu  
To configure the “Image Adjustment 1 J Contrast” setting  
1. Press the [MENU] key to display the setup menu.  
2. “Image Adjustment 1” is initially selected on the main menu, so simply press the  
[ENTER] key.  
3. Use the [T] key to select “Contrast”.  
4. Use the [W] (lighter) and [X] (darker) keys to adjust contrast.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
 
To configure the “Image Adjustment 1 J Color Mode” setting  
5. Use the [T] key to select “Color Mode”.  
6. Press the [ENTER] key.  
z This displays the color mode menu.  
7. Use the [T] and [S] keys to select the color mode you want, and then press the  
[ENTER] key.  
8. After selecting the color mode you want, press the [ESC] key.  
To configure the “Input Settings J Signal Name Indicator” setting  
9. Press the [ESC] key.  
10. Use the [T] key to select “Input Settings”.  
11. Press the [ENTER] key.  
12. Use the [T] key to select “Signal Name Indicator”.  
13. Use the [W] and [X] keys to select “On” or “Off”.  
14. After you are finished, press the [MENU] key to exit the setup menu.  
Direct Power On  
You can configure the projector so it powers up automatically as soon as you plug it into a power  
source. With this “Direct Power On” feature, you do not even need to press the [P] (Power) key. To  
enable Direct Power On, display the setup menu, and then change the “Direct Power On” setting to  
“On”.  
Important!  
When you have Direct Power On enabled, do not leave the projector plugged into an electrical  
outlet while it is turned off. If you do, there is the chance that it (and the light source unit) might  
turn on automatically when power is restored after being cut off by a power outage, tripping of a  
breaker, etc.  
Note  
z Direct Power On causes the projector to turn on automatically as soon as it is plugged into a  
power outlet. This greatly reduces the amount of time it takes until you are ready to start  
projecting. Note, however, that the actual startup sequence (Standby State J Power On J  
Projection Starts) that the projector performs is the same, regardless of whether Direct Power  
On is enabled or disabled. The only difference is what triggers the sequence (plugging in or  
pressing the [P] (Power) key).  
z For details about configuring the Direct Power On setting, see “Direct Power On” (page 39)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
 
Password Protecting the Projector  
The password feature lets you keep unauthorized individuals from using the projector. You can specify  
whether password input is required whenever you turn on the projector, and you can specify and  
change the password as required. Use the setup menu “Option Settings 1 J Power On Password”  
setting to configure power on password settings.  
Inputting a Password  
The password of your projector is not really a “word” made up of letters, but rather a sequence of  
remote controller key inputs. The following is the 8-key sequence that represents the initial factory  
default password.  
[INPUT] [AUTO] [BLANK] [FREEZE] [S] [T] [W] [X]  
Using the Password Feature  
Note the following precautions whenever you use the password feature.  
z The password feature protects against unauthorized use of the projector. Note that it is not an  
anti-theft measure.  
z You will need to enter the initial factory default password the first time you use the projector after  
turning on the password feature. Change the initial factory default password to a different one of  
your choice as soon as possible after turning on the password feature.  
z Remember that password operations are always performed using the remote controller, so you  
should take care not to lose or misplace the remote controller.  
z Also note that you will not be able to input the password if the remote controller batteries are dead.  
Replace the remote control batteries as soon as possible after it starts to go low.  
If you forget your password...  
You will not be able to use the projector if you forget the password for some reason. If you forget the  
password, you will need to bring the following two items to your CASIO distributor to have the  
password cleared. Note that you will be charged to have the password cleared.  
1. Personal identification (original or copy of your driver’s license, employee I.D., etc.)  
2. Projector unit  
Note that your CASIO distributor will not be able to clear the password of your projector unless you  
bring both of the items listed above.  
Also, keep the projector’s warranty in a safe place.  
Important!  
Having your password cleared using the procedure described above will return all of the settings  
of your projector, except for the Light Time, to their initial factory defaults.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
       
Keep a written record of your password!  
You will not be able to use the projector if you forget its password. We strongly suggest that you keep  
a written or other type of record of the password so you can look it up when necessary.  
To change the password  
1. Press the [MENU] key to display the setup menu.  
2. Use the [T] key to select “Option Settings 1”, and then press the [ENTER] key.  
3. Use the [T] key to select “Power On Password”, and then press the [ENTER]  
key.  
z This will display a dialog box prompting you to enter the current password.  
4. Enter the current password.  
z If the projector is still protected by the factory default password, perform the key operation  
shown below to enter it.  
[INPUT] [AUTO] [BLANK] [FREEZE] [S] [T] [W] [X]  
5. After entering the current password, press the [ENTER] key.  
z This displays the Power On Password setting screen.  
6. Use the [T] key to select “Change Password”, and then press the [ENTER] key.  
z This will display a dialog box prompting you to enter the new password.  
7. Enter a key sequence up to eight key operations long.  
z You can use any of the following keys as part of your password key sequence.  
[INPUT], [AUTO], [BLANK], [FREEZE], [VOLUME], [COLOR MODE], [D-ZOOM +], [D-ZOOM –],  
[KEYSTONE +], [KEYSTONE –], [MENU], [POINTER], [O], [f], [Z], [S], [T], [W], [X], [FUNC]  
8. After entering the new password, press the [ENTER] key.  
z This will display a dialog box prompting you to enter the same password again.  
9. Re-enter the same password key sequence you entered in step 7 and then press  
the [ENTER] key.  
z The message “Your new password has been registered.” indicates that the password has  
been changed. Press the [ESC] key.  
z If the password you entered in this step is different from the one you entered in step 7, the  
message “The password you input is wrong.” appears. Press the [ESC] key to return to step 7.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
 
To turn password protection on and off  
1. Display the Power On Password setting screen by performing steps 1 through 5  
of the procedure under “To change the password” on page 29.  
z At this time, make sure that “Power On Password” is selected on the Power On Password  
setting screen.  
2. Use the [W] and [X] keys to select “On” or “Off”.  
z Changing the power on password setting from “Off” to “On” causes the confirmation dialog  
box shown below to appear.  
Press the [ENTER] key to confirm that you want to turn on power on password protection, or  
[ESC] to exit the dialog box without doing anything.  
3. After you are finished, press the [MENU] key to exit the setup menu.  
Entering the Password when Turning On the Projector  
When you turn on the projector while password protection is turned on will cause a password input  
dialog box to appear on the projection screen. All projector operations will be accessible to you after  
you input the correct password and press the [ENTER] key.  
Note  
You can perform the projection size adjustment operation ([ZOOM +] / [ZOOM –] keys), focus  
operation ([FOCUS S] / [FOCUS T] keys), and power off operation ([P] (Power) key) while the  
password input dialog box is on the projection screen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
 
Restoring Projector Settings to Their Initial Factory  
Defaults  
You can use the procedures in this section to restore all of the settings on a particular main menu or all  
of the settings on the setup menu to their initial factory defaults.  
To restore all settings on a particular main menu to their initial factory  
defaults  
1. Press the [MENU] key to display the setup menu.  
2. Use the [T] and [S] keys to select the main menu whose settings you want to  
restore to their initial factory defaults.  
z You can select Image Adjustment 1, Image Adjustment 2, Volume Adjustment, Screen  
Settings, Input Settings, Option Settings 1, or Option Settings 2.  
3. Press the [ENTER] key.  
4. Use the [T] key to select “Restore Menu Defaults”.  
5. Press the [ENTER] key.  
z This will display a confirmation screen like the screen shown below.  
6. Use the [S] key to select “Yes”.  
7. To restore the settings of the main menu to their initial defaults, press the  
[ENTER] key.  
z To exit the operation without doing anything, press [ESC] instead of [ENTER].  
8. After you are finished, press the [MENU] key to exit the setup menu.  
Note  
z The language setting and the password are not returned to their initial factory defaults if you  
select Option Settings 1 in step 2.  
z For details about how the above procedure initializes settings, see the explanations of the  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
 
To restore all settings on the setup menu to their initial factory defaults  
1. Press the [MENU] key to display the setup menu.  
2. Use the [T] key to select “Restore All Defaults” and then press the [ENTER] key.  
3. After confirming that “Restore All Defaults” sub-menu is selected, press the  
[ENTER] key.  
z This displays a confirmation message asking if you want to initialize all settings.  
4. Use the [S] key to select “Yes”.  
5. To restore all settings on the setup menu to their initial defaults, press the  
[ENTER] key.  
z This will restore all of the settings to their initial factory defaults, except for the Language,  
Light Time, Unit Operating Time and password settings.  
z To exit the operation without doing anything, press [ESC] instead of [ENTER].  
6. After you are finished, press the [MENU] key to exit the setup menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32  
 
Setup Menu Contents  
This section contains tables that provide detailed explanations of all of the items included on the setup  
menu. The following describes the type of information that appears in each of the columns of the  
tables.  
Setting Name: This column shows the names of the settings as they appear on the sub-menu.  
Input: This column shows the input source for which each setting is supported.  
Input source names are abbreviated as follows:  
R : RGB input  
C : component video input  
V : video input  
H : HDMI (PC) input  
D : HDMI (DTV) input  
W : Wireless LAN input (USB port models only)  
U : USB input (USB port models only)  
The letter N indicates that the setting can be configured while there is no input signal.  
Setting Unit: The setting unit indicates how a setting is stored.  
“Source Specific” in this column indicates that separate settings can be stored for each  
individual input source.  
“Single” in this column indicates that a single setting is stored and applied, regardless of  
the input source.  
Description: This column provides details about the setting item and how to select it. The initial  
default setting is indicated by an asterisk (*).  
Image Adjustment 1 Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Brightness  
R C V H D W U  
Source  
Specific*1  
Use this sub-menu to adjust the brightness of the projected  
image. A larger value produces a brighter image.  
Contrast  
R C V H D W U  
Source  
Specific*1  
Use this sub-menu to adjust the contrast of the projected image.  
A larger value produces a stronger contrast.  
Sharpness  
V
Source  
Specific  
Use this sub-menu to adjust the sharpness of the outlines in the  
projected image. A larger value makes the image sharper, while a  
smaller value makes it softer.  
Saturation  
Tint  
V
V
Source  
Specific  
Use this sub-menu to adjust the color saturation of the projected  
image. A larger value increases color saturation.  
Source  
Specific  
Use this sub-menu to adjust the tint of the projected image.  
A larger value makes the overall image more bluish, while a smaller  
value makes the overall image more reddish. This setting is  
supported only when the signal is NTSC or NTSC4.43.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
   
Setting Name  
Input  
Setting Unit  
Description  
Color Mode  
R C V H D W U  
Source  
Specific*1  
You can select from among various different color mode settings  
in accordance with image contents and projection conditions.  
Standard:  
Use this setting when you want to highlight the colors of your  
presentation.  
Graphics:  
Use this setting when you want photographs and graphics to  
appear natural.  
Theater:  
Use this setting to bring out the dark portions of your images.  
Blackboard:  
Use this setting for easy viewing when projecting onto a  
blackboard.  
Game:  
Use this setting to optimize hue and brightness.  
Color Balance R C V H D W U  
Source  
Specific*1  
This sub-menu lets you adjust the color balance of the projected  
image.  
Preset:  
You can select from among three preset color balance settings:  
Warm, Normal,* Cold.  
Color:  
You can adjust the intensity of red, green, and blue within the  
range of –50 to +50. The intensity of a color increases along  
with the setting value. Color settings can be adjusted  
individually only when “Normal” is selected as the “Preset”  
setting.  
Eco Off Mode R C V H D W U  
Single  
When “Off” is selected for “Option Settings 1 J Eco Mode”, you  
can select either of the following projection image modes.  
Bright:  
Gives priority to brightness.  
Normal:  
Suppresses brightness slightly and gives priority to color  
balance.  
Restore Menu R C V H D W U  
Defaults  
Source  
Specific*1  
Use this sub-menu to return all of the sub-menu items on the  
Image Adjustment 1 main menu to their initial default settings.  
z Restoring menu defaults when there is no input signal will  
restore defaults for the currently selected input source.  
*1 The same setting value is saved for both wireless LAN input (W) and USB input (U).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
34  
   
Image Adjustment 2 Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Vertical  
Position  
R C V  
R C V  
R
Signal  
Specific  
Use this sub-menu to adjust the vertical position of the input  
source image within the projection area.  
Horizontal  
Position  
Signal  
Specific  
Use this sub-menu to adjust the horizontal position of the input  
source image within the projection area.  
Frequency  
Signal  
Specific  
When vertical bands appear in the projected image while RGB is  
selected as the input source, it means that the frequency setting is  
not correct. When this happens, use this setting to adjust the  
frequency manually.  
Important!  
If, for some reason, your manual frequency settings cause  
the image input from the computer to disappear from the  
projection, you can press the [AUTO] key to perform an auto  
adjust operation, which should cause the image to appear.  
Phase  
R
Signal  
Specific  
When there is flickering in the projected image while RGB is  
selected as the input source, it means that the phase setting is not  
correct. When this happens, use this setting to adjust the phase  
manually.  
Restore Menu R C V  
Defaults  
Source  
Specific  
Use this sub-menu to return all of the sub-menu items on the  
Image Adjustment 2 main menu to their initial default settings.  
z Restoring menu defaults will restore defaults for the current  
signal type (XGA/60Hz, SXGA/60Hz, etc.) only.  
About the “Signal Specific” Setting Unit  
For the items that have “Signal Specific” in the “Setting Unit” column of the above table, the setting is  
saved for the specific type of signal (XGA/60Hz, SXGA/60Hz, etc.) that is being input when the setting  
is performed, and not for a specific input source.  
Volume Adjustment Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Volume  
R C V H D W U N Source  
Use this sub-menu to adjust the volume level of the projector’s  
speaker or the AV terminal.  
Specific*1  
z Changing this setting when there is no input signal changes the  
volume setting of the currently selected signal source.  
Restore Menu R C V H D W U N Source  
Defaults  
Specific*1  
Use this sub-menu to return Volume to its initial default setting.  
z Restoring menu defaults when there is no input signal will  
restore defaults for the currently selected input source.  
*1 The same setting value is saved for both wireless LAN input (W) and USB input (U).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
35  
     
Screen Settings Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Keystone  
Correction  
R C V H D W U N Single  
Use this sub-menu to perform vertical keystone correction of the  
projected image.  
Aspect Ratio  
R C V H D  
Source  
Specific  
Use this sub-menu to select an aspect ratio setting for the  
projected image.  
Input Source: RGB or HDMI (PC)  
Normal*:  
Projects at the projector’s maximum possible size while  
maintaining the input signal aspect ratio.  
Full:  
Projects at the projector’s maximum possible size by enlarging  
or reducing the input signal.  
4:3 (XJ-A241/XJ-A246/XJ-A251/XJ-A256 only):  
Regardless of the input signal aspect ratio, the image is always  
resized to an aspect ratio of 4:3 for projection.  
True (XJ-A241/XJ-A246/XJ-A251/XJ-A256 only):  
Projects the input signal at its actual size (1 input source dot  
equal to one projector output pixel dot) in the center of the  
projector’s projection screen. If the input signal resolution  
exceeds the projector’s output resolution, the excess is cut off.  
Input Source: Video, Component or HDMI  
(DTV)  
Normal*:  
Projects at the projector’s maximum possible size while  
maintaining the input signal aspect ratio.  
16:9 :  
This setting specifies a 16:9 aspect ratio, which is the same as a  
movie screen, high-definition TV, etc. Using this setting when  
the input signal is a 16:9 image that has been squeezed to a 4:3  
image causes the image to be displayed with its normal 16:9  
aspect ratio.  
4:3 (XJ-A241/XJ-A246/XJ-A251/XJ-A256 only):  
Regardless of the input signal aspect ratio, the image is always  
resized to an aspect ratio of 4:3 for projection.  
Letter Box (XJ-A241/XJ-A246/XJ-A251/XJ-A256 only):  
This will resize the image horizontally to 1280 dots and project  
800 vertical dots of the center of the image, maintaining the  
aspect ratio of the input signal.  
Note  
z When projecting while “True” is selected as the aspect  
ratio setting for an RGB signal with a resolution that is  
less than SVGA, the image is enlarged to SVGA and  
projected.  
z For details about projection screen display conditions for  
different aspect ratio settings, see “Aspect Ratio Setting  
Important!  
Note that enlarging or reducing the size of an image for  
commercial purposes or public presentation may infringe on  
the legally protected copyright of the copyright holder of the  
original material.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
36  
   
Setting Name  
Input  
Setting Unit  
Description  
Projection  
Mode  
R C V H D W U N Single  
Use this sub-menu to specify whether projection will be from the  
front of the screen or the back of the screen.  
Front*:  
Select this option to project from the front of the screen.  
Rear:  
Select this option to project from the back of the screen. This  
setting flips the front projected image horizontally.  
Ceiling Mount R C V H D W U N Single  
Use this sub-menu to configure the projector for use in an  
installation in which it is positioned upside down.  
On:  
Flips the projected image horizontally and vertically.  
Off*:  
Projects a normal image.  
Startup Screen R C V H D W U N Single  
Use this sub-menu to specify whether or not a startup screen  
should be projected whenever the projector is turned on.  
Logo:  
Select this option to project the projector’s built-in logo screen  
at startup.  
None*:  
Select this option when you do not want to project a startup  
screen.  
No Signal  
Screen  
R C V H D W U N Single  
Use this sub-menu to specify what should be projected when  
there is no input signal to the projector.  
Blue*:  
Select this option to project a blue screen.  
Black:  
Select this option to project a black screen.  
Logo:  
Select this option to project the projector’s built-in logo screen.  
Blank Screen  
R C V H D W U N Single  
Use this sub-menu to specify what should be projected after the  
[BLANK] key is pressed.  
Blue:  
Select this option to project a blue screen.  
Black*:  
Select this option to project a black screen.  
Logo:  
Select this option to project the projector’s built-in logo screen.  
Restore Menu R C V H D W U N Source  
Defaults Specific  
Use this sub-menu to return all of the sub-menu items on the  
Screen Settings main menu to their initial default settings.  
z Restoring menu defaults when there is no input signal will  
restore defaults for the currently selected input source.  
z Note that the “Keystone Correction”, “Projection Mode”,  
“Ceiling Mount”, “Startup Screen”, “No Signal Screen”, and  
“Blank Screen” settings are always returned to their initial  
defaults, regardless of the currently selected input source.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
   
Input Settings Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
COMPUTER  
Terminal  
R C  
N
Single  
Use this sub-menu to specify manually the type of signal being  
input from the projector’s COMPUTER terminal.  
Auto*:  
Automatically detects the signal being input from the  
COMPUTER terminal and configures the appropriate input  
protocol.  
RGB:  
Select this option when a computer is connected to the  
COMPUTER terminal. For details about connecting a computer,  
Projector” (page 11).  
Component:  
Select this setting when the projector’s COMPUTER terminal is  
connected to the component video output terminal of a video  
device using a commercially available component video cable.  
For information about connection, see “Connecting to a Video  
Device” (page 13).  
Video Signal  
V
N
Single  
Use this sub-menu to specify manually the type of signal being  
input from the projector’s AV terminal.  
Auto*:  
Select this setting to have the projector switch the video signal  
system automatically in accordance with the input signal from  
the video device that is connected to the AV terminal.  
NTSC / NTSC4.43 / PAL / PAL-M / PAL-N / PAL60 / SECAM:  
Each setting selects the applicable video system. Use these  
settings when you want to specify only one specific video signal  
for the AV terminal.  
Signal Name  
Indicator  
R C V H D W U N Single  
Use this sub-menu to specify whether or not the name of the  
currently selected signal source should be displayed in the  
projected image.  
On*:  
Select this option to turn on display of the name of the currently  
selected signal source in the projected image.  
Off:  
Select this option to turn off display of the signal source name.  
Restore Menu R C V H D W U N Source  
Defaults Specific  
Use this sub-menu to return all of the sub-menu items on the Input  
Settings main menu to their initial default settings.  
z Restoring menu defaults when there is no input signal will  
restore defaults for the currently selected input source.  
z Note that the “Signal Name Indicator” setting is always returned  
to its initial default, regardless of the currently selected input  
source.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38  
   
Option Settings 1 Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Auto Keystone R C V H D W U N Single  
Correction  
Use this sub-menu to turn auto keystone correction on or off.  
On*:  
Select this option to turn on auto keystone correction.  
Off:  
Select this option to turn off auto keystone correction.  
Auto Adjust  
R
N
Source  
Use this sub-menu to select whether the projector should detect  
Specific  
the RGB input signal type (resolution, frequency) and adjust the  
projection image accordingly (auto adjust).  
1*:  
Select this option to turn on auto adjust.  
2:  
Select this option to turn on auto adjust when a 1360 × 768 or  
1400 × 1050 signal is not projected correctly.  
3:  
Select this option to turn on auto adjust when a 1366 × 768  
signal is not projected correctly.  
Off:  
Select this option to turn off auto adjust.  
Eco Mode  
R C V H D W U N Single  
Auto Power Off R C V H D W U N Single  
Auto Power Off lets you specify the amount of time of projector  
operation and input signal inactivity to be allowed before Auto  
Power Off is triggered to turn off projector power automatically.  
Auto Power Off can be disabled, if you want.  
5 min, 10 min*, 15 min, 20 min, 30 min:  
Time until Auto Power off is triggered.  
Off:  
Disables Auto Power Off.  
Power On  
Password  
R C V H D W U N Single  
R C V H D W U N Single  
You can configure the projector to require input of a password  
before operation is enabled. For details, see “Password Protecting  
Direct Power  
On  
Use this sub-menu to turn Direct Power On on or off. See “Direct  
Power On” on page 27.  
On:  
Select this option to turn on Direct Power On.  
Off*:  
Select this option to turn off Direct Power On.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
     
Setting Name  
Input  
Setting Unit  
Description  
Language  
R C V H D W U N Single  
Use this sub-menu to specify the language to use for messages,  
setup menus, etc.  
English / French / German / Italian / Spanish / Swedish /  
Portuguese / Turkish / Russian / Chinese (Simplified) /  
Chinese (Traditional) / Korean / Japanese  
Note  
(for USB port model users)  
If you have Portuguese, Turkish, or Russian selected as the  
projector’s language, selecting an external device  
connected to the projector’s USB port or wireless adapter  
as the input source will cause some menus and messages  
to be displayed in English.  
Restore Menu R C V H D W U N Single  
Defaults  
This sub-menu returns all of the sub-menu items on the Option  
Settings 1 main menu to their initial default settings.  
z The language setting and the password are not returned to their  
initial factory defaults.  
z The “Auto Adjust” item is returned to its initial default only when  
RGB input is selected for the input source. All of the other items  
are returned to their initial defaults regardless of the currently  
selected input source.  
Option Settings 2 Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Zoom Memory R C V H D W U N Single  
This sub-menu specifies whether the current zoom setting  
(projection size) should be saved when the [P] (Power) key is  
pressed to turn the projector off. A saved projection size setting is  
restored the next time the projector is turned on.  
On*:  
Select this option to automatically restore the projection size in  
effect the last time the projector was turned off by pressing the  
[P] (Power) key.  
Off:  
Select this option to have the projector configured the  
maximum projection size whenever it is turned on.  
Note  
The current zoom setting is not saved if projector power is  
turned off by unplugging the power cord without pressing  
the [P] (Power) key. If you want the current projection size  
to be saved and restored, be sure to press the [P] (Power)  
key to turn the projector off.  
Pointer  
R C V H D W U N Single  
Use this sub-menu to specify the type of pointer that appears first  
when you press the [POINTER] key.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40  
     
Setting Name  
Input  
Setting Unit  
Description  
Plug and Play R C V H D W U N Single  
(USB port  
Use this sub-menu to turn plug-and-play*1 on or off.  
On*:  
models only)  
Select this option to turn on plug-and-play. This will allow the  
projector detect when an external USB device is connected and  
make that device the input source automatically.  
Off:  
Select this option to turn off plug-and-play.  
USB Audio Out R C V H D W U N Single  
(USB port  
models only)  
When playing back a movie file stored on a USB memory device,  
you can select audio output from the projector’s built-in speaker  
or to the line output.  
Speaker*:  
Select to output movie file audio from the speaker.  
Line:  
Select to output movie file audio from the AV terminal.  
HDMI Audio  
Out  
R C V H D W U N Single  
Specifies whether the input audio signal should be output from the  
projector’s built-in speaker or to the line output.  
Speaker*:  
Outputs the audio signal being input to the HDMI port from the  
speaker.  
Line:  
Outputs the audio signal being input to the HDMI port from the  
AV terminal.  
High Altitude  
R C V H D W U N Single  
Use this sub-menu to turn the high-altitude fan speed setting on or  
off in accordance with the altitude of the area where you are using  
the projector.  
On:  
Select this setting when using the projector in a high altitude  
(1,500 to 3,000 meters above sea level) area where air is thin.  
This setting increases cooling efficiency.  
Off*:  
Select this setting at normal altitudes (up to 1,500 meters).  
Important!  
Do not use this projector at altitudes greater than  
3,000 meters above sea level.  
Timer Function R C V H D W U N Single  
Selecting this item displays the timer function menu. For details,  
Restore Menu R C V H D W U N Single  
Defaults  
This sub-menu returns all of the sub-menu items on the Option  
Settings 2 main menu to their initial default settings.  
*1 When plug-and-play is turned on, the projector will make that device the input source  
automatically. For details about plug-and-play, see “USB Function Guide” on the bundled  
CD-ROM.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
   
USB Settings Main Menu (USB Port Models Only)  
The USB Settings main menu is available only when there is an external device connected to the USB  
port of the projector. For details, see “USB Function Guide” on the bundled CD-ROM.  
Wireless Main Menu (USB Port Models Only)  
The Wireless main menu is available only when “Wireless” is selected as the input source on the  
projector. For more information, see the “Wireless Function Guide” on the CD-ROM that comes with  
the projector.  
Operational Info Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Input Signal  
R C V H D W U N Source  
Specific  
This sub-menu item shows the currently selected input signal  
(RGB, Component, Video, HDMI (PC), or HDMI (DTV)). “- - - -” is  
indicated here when there is no input signal.  
Signal Name  
Resolution  
R C V H D  
U
Source  
Specific  
This sub-menu item shows the signal name of the signal being  
input to the projector. For details about signal names, see “Signal  
Name” under “Supported Signals” (page 53).  
R
H
Source  
Specific  
This sub-menu item appears only when RGB is the input signal. It  
shows the number of vertical and horizontal pixels of resolution of  
the RGB or HDMI (PC) input signal.  
Horizontal  
Frequency  
R C V H D  
R C V H D  
Source  
Specific  
This sub-menu item shows the horizontal frequency of the input  
signal.  
Vertical  
Frequency  
Source  
Specific  
This sub-menu item shows the vertical frequency of the input  
signal.  
Scan System  
R C  
H D  
Source  
Specific  
This sub-menu item appears only when RGB, Component,  
HDMI (PC), or HDMI (DTV) is the input signal, and shows the scan  
system of the input signal. The scan system is interlace or  
non-interlace for an RGB or HDMI (PC) signal input, and interlace  
or progressive for a component or HDMI (DTV) signal input.  
Light Time  
R C V H D W U N Single  
This sub-menu item shows the cumulative number of hours the  
current light source unit has been used to date.  
Restore All Defaults Main Menu  
Setting Name  
Input  
Setting Unit  
Description  
Unit Operating R C V H D W U N Single  
Time  
This sub-menu item shows the cumulative operating time of this  
unit. This time cannot be initialized.  
Restore All  
Defaults  
R C V H D W U N Single  
This sub-menu returns all sub-menu items on all main menus to  
their initial default settings. This operation can be performed  
regardless of the currently selected input source and regardless  
of whether or not a signal is currently being input. For details  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
42  
         
Cleaning the Projector  
Periodically clean the projector exterior, lens, intake vents, and exhaust vents on a regular basis.  
Important!  
Before cleaning the projector, be sure to unplug it from the power outlet and make sure it is  
cooled down completely.  
Cleaning the Projector Exterior  
Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water  
and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping.  
Never use benzene, alcohol, thinner, or any other volatile agent for cleaning.  
Cleaning the Lens  
Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for  
eyeglasses or camera lenses. When cleaning the lens, do not apply undue force and take care to avoid  
damaging the lens.  
Cleaning Intake and Exhaust Vents  
Dust and dirt tend to collect around the intake vents. Because of this, you should use a vacuum  
cleaner to clean away accumulated dust and dirt periodically as shown below.  
Important!  
z Continued use of the projector after dust has accumulated around the intake vents can cause  
overheating of internal components and lead to malfunction.  
z Certain operating conditions also can cause dirt and dust to accumulate around the  
projector’s exhaust vents. If this happens, use the same procedure as that described above to  
clean the exhaust vents.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
       
Troubleshooting  
Indicators  
Indicators keep you informed about the current operational status of the projector. The following  
shows what the indicators look like when operation is normal.  
When the indicators appear  
It means this:  
like this:  
POWER/  
STANDBY  
You have just plugged the AC power cord into a power outlet. Wait  
until the projector enters the standby state (see below) before trying  
to turn on power.  
LIGHT  
TEMP  
z
z
z
Amber  
Amber  
Amber  
z
c
c
Standby state: The AC power cord is plugged in and the projector is  
in standby.  
Amber  
Projector is warming up after being turned on.  
z
z
Green  
Amber  
Amber  
z
c
c
c
c
c
Projector is on and standing by for use.  
Green  
Projector is performing internal power down processes.  
Amber  
“On (Auto)” or “On (Manual)” is selected for the projector’s Eco Mode  
z
z
Green  
Green  
: Lit  
: Flashing  
: Unlit  
z
c
When a warning message appears on the projection screen, or when the POWER/STANDBY, LIGHT,  
and TEMP indicators are lit or flashing in a pattern other than those shown above, it means that a  
projector error has occurred. For details, see “Error Indicators and Warning Messages” (below).  
Error Indicators and Warning Messages  
Warning messages and indicators let you know what the problem is when a projector error occurs.  
When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug the  
AC power cord while the fan is still operating, an error may occur when you plug the AC power cord  
back in.  
Indicator/Error Message  
Description and Required Action  
POWER : Green steady  
The projector’s internal temperature is very high. Press the [ESC] key to  
clear the warning message and perform the following steps.  
1 Check for any blocking of the projector’s intake vents and exhaust  
vents, and make sure that there is sufficient space around the  
projector. See Setup Precautions” (page 10).  
2 If there is dust accumulated around the intake vents and/or exhaust  
vents, turn off the projector and remove it. See Cleaning the  
Projector” (page 43).  
LIGHT  
TEMP  
: –  
: –  
Message : Internal temperature is too  
high. Check projector air  
vents for blockage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44  
     
Indicator/Error Message  
Description and Required Action  
POWER : Amber flashing J  
Power has turned off automatically due to internal overheating. Perform  
the following steps.  
Amber steady  
1 Check for any blocking of the projector’s intake vents and exhaust  
vents, and make sure that there is sufficient space around the  
projector. See Setup Precautions” (page 10).  
LIGHT  
TEMP  
: –  
: –  
2 If there is dust accumulated around the intake vents and/or exhaust  
vents, remove it. See Cleaning the Projector” (page 43).  
If there is no problem with the projector’s vents, confirm that the POWER/  
STANDBY indicator is lit amber (without flashing), and then turn power  
back on again. If the error occurs again when you turn power back on,  
contact your retailer or nearest authorized CASIO Service Center.  
Message : Internal temperature is too  
high. The projector will  
turn off.  
POWER : Amber flashing J  
Power has turned off automatically due to internal overheating. This  
causes a dialog box containing the text in the next item below to appear  
the next time you turn on the projector. Follow the steps that are  
provided.  
Red steady  
LIGHT  
TEMP  
: –  
: Red flashing  
(0.5-second interval)  
Message : –  
POWER : Green steady  
The last time you were using the projector, power turned off automatically  
due to internal overheating. Press the [ESC] key to clear the warning  
message and perform the following steps.  
LIGHT  
TEMP  
: –  
: –  
1 Check for any blocking of the projector’s intake vents and exhaust  
vents, and make sure that there is sufficient space around the  
projector. See Setup Precautions” (page 10).  
2 If there is dust accumulated around the intake vents and/or exhaust  
vents, turn off the projector and remove it. See Cleaning the  
Projector” (page 43).  
Message : The projector has a  
history of turning off due  
to high temperature.  
Check air vents for  
blockage.  
3 Disconnect the power cord from the projector and wait for all of the  
projector’s indicators to go out. Next, reconnect the power cord and  
turn the projector back on. If the error occurs again when you turn  
power back on, contact your retailer or nearest authorized CASIO  
Service Center.  
POWER : Amber flashing J  
Power has turned off automatically due to a fan problem. Confirm that the  
POWER/STANDBY indicator is lit red (without flashing) and that the fan  
has stopped. After checking the POWER/STANDBY indicator, disconnect  
the power cord from the projector and wait for all of the projector’s  
indicators to go out. Next, reconnect the power cord and turn projector  
power back on.  
Red steady  
LIGHT  
TEMP  
: Red steady  
: Red steady  
Message : There is a problem with  
the fan. The projector will  
turn off.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
POWER : Amber flashing J  
Power has turned off automatically due to a system problem. After  
confirming that the POWER/STANDBY indicator is lit red (without  
flashing), disconnect the power cord from the projector and wait for all of  
the projector’s indicators to go out. Next, reconnect the power cord and  
turn the projector back on.  
Red steady  
LIGHT  
TEMP  
: –  
: Red steady  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
Message : A system problem has  
occurred. The projector  
will turn off.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
Indicator/Error Message  
Description and Required Action  
POWER : Green steady  
A system problem has occurred, which may cause problems with some  
functions. Turn off the projector, disconnect the power cord from the  
projector and wait for all of the projector’s indicators to go out. Next,  
reconnect the power cord and turn the projector back on.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
LIGHT  
TEMP  
: –  
: –  
Message : A system problem has  
occurred. Normal  
Press the [ESC] key to clear the warning message.  
projection is not possible.  
POWER : Green steady  
LIGHT  
TEMP  
: –  
: –  
Message : There is some problem  
with the system.  
The audio function may  
not operate correctly.  
POWER : Green steady  
The USB connection was terminated because of a problem with the USB  
port. To use the USB function, turn off the projector and then turn it back  
on again.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
Press the [ESC] key to clear the warning message.  
LIGHT  
TEMP  
: –  
: –  
Message : There is a problem with  
the USB port.  
POWER : Green steady  
Zoom and focus cannot be performed due to some trouble in the optical  
drive circuit. Turn off the projector and then turn it back on again.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
LIGHT  
TEMP  
: –  
: –  
Press the [ESC] key to clear the warning message.  
Message : Zoom and focus cannot  
be performed for some  
reason. Try turning the  
projector off and then  
back on again.  
If this message reappears,  
request servicing.  
POWER : Amber flashing J  
The projector was turned off automatically due to some problem that was  
probably caused by external digital noise or some other reason. Confirm  
that the POWER/STANDBY indicator is lit red (without flashing). After  
checking the POWER/STANDBY indicator, disconnect the power cord  
from the projector and wait for all of the projector’s indicators to go out.  
Next, reconnect the power cord and turn projector power back on.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
Red steady  
LIGHT  
TEMP  
: –  
: Red steady  
Message : –  
POWER : Amber flashing J  
The projector was turned off automatically because the light source unit  
turned off or did not turn on. After confirming that the POWER/STANDBY  
indicator is lit red (without flashing), unplug the power cord. Wait for a  
short while and then plug it back in and turn on the projector again.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
Red steady  
LIGHT  
TEMP  
: Red flashing  
(0.5-second interval)  
: Red flashing  
(0.5-second interval)  
Message : –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
46  
Indicator/Error Message  
Description and Required Action  
POWER : Amber flashing J  
Power has turned off automatically due to a projector memory error.  
Confirm that the POWER/STANDBY indicator is lit red (without flashing).  
After checking the POWER/STANDBY indicator, disconnect the power  
cord from the projector and wait for all of the projector’s indicators to go  
out. Next, reconnect the power cord and turn projector power back on.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
Red steady  
LIGHT  
TEMP  
: Not lit or red flashing  
: Red flashing  
(2-second interval)  
Message : –  
POWER : Amber flashing J  
Power has turned off automatically because the light source unit cover is  
open. Perform the following steps.  
Red steady  
1 After confirming that the POWER/STANDBY indicator is lit red (without  
flashing), disconnect the power cord from the projector.  
2 Check to make sure that the light source unit cover is closed.  
3 Plug the power cord back in and turn the projector back on again.  
If the error occurs again when you turn power back on, contact your  
retailer or nearest authorized CASIO Service Center.  
LIGHT  
TEMP  
: –  
: Amber flashing  
(1-second interval)  
Message : –  
Projector Troubleshooting  
Check the following items whenever you experience any problem with the projector.  
Problem  
Cause and Recommended Action  
Power does not turn on.  
z If the POWER/STANDBY indicator is not lit, the AC power cord is not connected  
correctly. Connect the AC power cord correctly.  
z If the TEMP or LIGHT indicator remains flashing or lit, it means some type of error  
No image is projected or  
the projected image is  
abnormal.  
z The computer or video device connected to the projector is not turned on or it is  
not outputting a video signal. Make sure the connected computer or video device  
is turned on, and perform the required operation on it to output a video signal.  
z The correct output source is not selected on the projector. On the projector, select  
the correct input source that corresponds to the connected device.  
z Images may not project correctly when you have the component output terminal of  
a video device connected to the COMPUTER terminal of the projector. Connect to  
the AV terminal of the projector.  
Image color or display is  
very abnormal.  
The wrong option (“Component” or “RGB”) may be selected for the “Input Settings J  
COMPUTER Terminal” setting on the setup menu. The image will not be projected  
correctly if “Component” is selected while the projector’s COMPUTER terminal is  
connected to the RGB output terminal of a computer, or if “RGB” is selected while the  
projector’s COMPUTER terminal is connected to the component video output  
terminal of a video device. On the setup menu, select “Auto” for the “Input Settings J  
COMPUTER Terminal” setting. See page 38.  
I can’t understand  
messages or menus  
because they are the  
wrong language.  
Perform the following operation to select the language you want. See page 40.  
1. Press the [MENU] key to display the setup menu.  
2. If the input signal is HDMI, press [T] four times and then press the [ENTER] key. If  
the input signal is not HDMI, press [T] five times and then press the [ENTER] key.  
3. Press [S] twice and then press the [ENTER] key to display the language selection  
menu.  
4. Use the [T] and [S] keys to move the highlighting to the language you want to  
select and then press the [ENTER] key.  
5. Press the [MENU] key to exit the setup menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
 
Problem  
No sound  
Cause and Recommended Action  
z The projector’s volume level setting may be too low or muted. Press the remote  
controller [VOLUME] key and then use [W] and [X] to adjust the volume level. See  
z The volume level setting of the device connected to the projector is too low or the  
other device is not outputting audio. Adjust the volume level of the connected  
device.  
z The audio output of the connected device may not be connected correctly to the  
projector’s AV terminal. Check the connection, referring to one of the following  
(depending on the type of connected device): “Connecting the Analog RGB Output  
(page 13).  
z When a video device’s or computer’s HDMI output is connected to the HDMI port  
of the projector, “Line” may be selected for the “Option Settings 2 J HDMI Audio  
Out” setting on the setup menu. Change the “HDMI Audio Out” setting to  
“Speaker”. See page 41.  
Strange color  
Text is blurry.  
The input signal may not match projector settings. Try doing the following.  
Use the [BRIGHT] key to adjust image brightness.  
Use the [COLOR MODE] key to change the color mode.  
On the setup menu, use “Image Adjustment 1 J Color Balance” to adjust the  
projection image color balance.  
z The image may be out of focus. On the remote controller, use the [FOCUS S] and  
[FOCUS T] keys to adjust image focus.  
z The current frequency and/or phase setting do not match the input signal. (Applies  
only when the input source is an RGB signal.) Press the [AUTO] key to execute an  
automatic adjustment operation.  
z On the setup menu, perform the “Image Adjustment 2 J Frequency” and “Image  
Adjustment 2 J Phase” adjustments. (Applies only when the input source is an  
RGB signal.) See page 35.  
z If the input source is a video camera or document camera, check to make sure  
there is no problem with the input source device.  
The message “Please input The “Option Settings 1 J Power On Password” setting on the setup menu is turned  
the password.” appears on, so the projector is password protected. Input the correct password, and then  
and further operation is not press the [ENTER] key. See page 28.  
possible.  
The remote controller does z The remote controller batteries may be dead. Replace the batteries.  
not work.  
z The remote controller may be too far from the projector. Make sure the remote  
controller is within the allowable range when you operate it. See page 49.  
The TEMP or LAMP  
An error occurred. See “Error Indicators and Warning Messages” (page 44).  
indicator is flashing or lit.  
The light source unit does The light source unit has reached the end of its service life or it is malfunctioning.  
not light. Contact your original dealer or authorized CASIO service center for replacement.  
Important!  
z Try performing the following steps, which may or may not return the projector to normal  
operation.  
1. Unplug the AC power cord and wait for at least 10 minutes.  
2. Plug the power cord back in and turn the projector back on again.  
z If normal operation does not resume after you perform the above steps, take the projector to  
your retailer or authorized CASIO service center.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48  
Appendix  
Remote Controller Signal Range  
When performing an operation on the remote controller, point it at the remote control signal receiver  
on the back or front of the projector. The following illustration shows the range of the remote controller  
signal.  
30 degrees max.  
5 meters (16.4 feet)  
max.  
30 degrees max.  
5 meters (16.4 feet)  
max.  
Front  
Back  
5 degrees to  
30 degrees  
30 degrees max.  
5 meters (16.4 feet) max.  
5 meters (16.4 feet)  
max.  
Remote Controller Range  
z The range of the remote controller may be narrower and/or shorter than that shown on the right  
(Back) when there is a special AV cable plugged into the AV terminal on the back of the projector.  
z The allowable distance between the remote controller and the projector is less when there is a  
sharp angle between the remote controller and the remote control signal receiver.  
Important!  
To avoid running down the batteries, store the remote control unit so its keys are not pressed  
inadvertently.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
49  
   
Projection Distance and Screen Size  
h*  
The following table shows the relationship between the distance and projected image size.  
Approximate Projection Distance  
Projection Size  
XJ-A141/XJ-A146  
XJ-A241/XJ-A246/XJ-A251/XJ-A256  
Minimum  
Distance  
(m / feet)  
Maximum  
Distance  
(m / feet)  
Minimum  
Distance  
(m / feet)  
Maximum  
Distance  
(m / feet)  
Screen  
Size  
Diagonal  
(cm)  
h*  
h*  
(cm / inch)  
40  
60  
102  
152  
203  
254  
381  
508  
1.1 / 3.61  
1.7 / 5.58  
2.3 / 7.55  
2.8 / 9.19  
4.3 / 14.11  
5.7 / 18.70  
2.2 / 7.22  
3.4 / 11.15  
4.5 / 14.76  
5.6 / 18.37  
8.5 / 27.89  
11.3 / 37.07  
0
0
0
0
0
0
1.0 / 3.28  
1.4 / 4.59  
1.9 / 6.23  
2.4 / 7.87  
3.6 / 11.81  
4.8 / 15.75  
1.9 / 6.23  
2.8 / 9.19  
3.8 / 12.47  
4.8 / 15.75  
7.2 / 23.62  
9.6 / 31.50  
9 / 3.54  
14 / 5.51  
18 / 7.09  
23 / 9.06  
34 / 13.39  
45 / 17.72  
80  
100  
150  
200  
* h = Height from the center of the lens to the bottom edge of the projection screen.  
Important!  
Note that the distances provided above are for reference only.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50  
 
Aspect Ratio Setting and Projection Image  
The following shows how images are projected in accordance with the type of the input signal and the  
aspect ratio setting of the projector.  
XJ-A241/XJ-A246/XJ-A251/XJ-A256  
Input source: RGB or HDMI (PC)  
Input Signal  
Normal  
Full  
4:3  
True  
SVGA (800 × 600)  
XGA (1024 × 768)  
WXGA (1280 × 800)  
SXGA (1280 × 1024)  
Input source: Video, component or HDMI (DTV)  
Input Signal  
4:3 Aspect Image  
Squeezed Image  
Letter Box Image  
16:9 Aspect Image  
Normal  
16:9  
4:3  
Letter Box  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
51  
   
XJ-A141/XJ-A146  
Input source: RGB or HDMI (PC)  
Input Signal  
Normal  
Full  
SVGA (800 × 600)  
XGA (1024 × 768)  
WXGA (1280 × 800)  
SXGA (1280 × 1024)  
Input source: Video, component or HDMI (DTV)  
Input Signal  
Normal  
16:9  
4:3 Aspect Image  
Squeezed Image  
Letter Box Image  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
52  
Supported Signals  
Important!  
Even if a signal is listed in the table below, it does not guarantee that you will be able to display  
its images correctly.  
RGB Signal  
Horizontal Frequency Vertical Frequency  
Signal Name  
Resolution  
(kHz)  
31.5  
37.9  
37.5  
43.3  
35.2  
37.9  
48.1  
46.9  
53.7  
48.4  
56.5  
60.0  
68.7  
67.5  
47.8  
49.7  
60.0  
85.9  
64.0  
80.0  
91.1  
47.7  
47.7  
65.3  
55.9  
75.0  
65.3  
64.0  
64.0  
(Hz)  
60  
73  
75  
85  
56  
60  
72  
75  
85  
60  
70  
75  
85  
75  
60  
60  
60  
85  
60  
75  
85  
60  
60  
60  
60  
60  
60  
70  
60  
VESA  
640 × 480/60  
640 × 480  
640 × 480/72  
640 × 480  
640 × 480/75  
640 × 480  
640 × 480/85  
640 × 480  
800 × 600/56  
800 × 600/60  
800 × 600  
800 × 600  
800 × 600/72  
800 × 600  
800 × 600/75  
800 × 600  
800 × 600/85  
800 × 600  
1024 × 768/60  
1024 × 768/70  
1024 × 768/75  
1024 × 768/85  
1152 × 864/75  
1280 × 768/60  
1280 × 800/60  
1280 × 960/60  
1280 × 960/85  
1280 × 1024/60  
1280 × 1024/75  
1280 × 1024/85  
1360 × 768/60*1  
1366 × 768/60*2  
1400 × 1050/A*1  
1440 × 900/60  
1600 × 1200/60  
1680 × 1050/60  
1152 × 864/70  
1400 × 1050/B*1  
1024 × 768  
1024 × 768  
1024 × 768  
1024 × 768  
1152 × 864  
1280 × 768  
1280 × 800  
1280 × 960  
1280 × 960  
1280 × 1024  
1280 × 1024  
1280 × 1024  
1360 × 768  
1366 × 768  
1400 × 1050  
1440 × 900  
1600 × 1200  
1680 × 1050  
1152 × 864  
1400 × 1050  
Other  
*1 If these signals do not project correctly, change the “Option Settings 1  
Auto Adjust” setting to “2”  
Auto Adjust” setting to “3”  
J
J
(page 39).  
*2 If this signal does not project correctly, change the “Option Settings 1  
(page 39).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
53  
   
Component Signal  
Signal Name  
1080p/50  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
HDTV  
56.3  
67.5  
37.5  
45.0  
28.1  
33.7  
31.3  
16.6  
31.5  
15.7  
50  
60  
50  
60  
50  
60  
50  
50  
60  
60  
1080p/60  
720p/50  
720p/60  
1080i/50  
1080i/60  
576p/50  
576i/50  
SDTV  
480p/60  
480i/60  
Video Signal  
Signal Name  
NTSC  
Horizontal Frequency (kHz)  
15.7  
Vertical Frequency (Hz)  
60  
60  
50  
60  
50  
60  
50  
NTSC4.43  
PAL  
15.7  
15.6  
15.7  
15.6  
15.7  
15.6  
PAL-M  
PAL-N  
PAL60  
SECAM  
HDMI Signal  
Signal Name  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
640 × 480/60  
31.5  
37.9  
48.4  
47.8  
49.7  
60  
60  
60  
60  
60  
60  
60  
60  
60  
60  
50  
50  
60  
50  
60  
50  
60  
800 × 600/60  
1024 × 768/60  
1280 × 768/60  
1280 × 800/60  
1280 × 960/60  
1280 × 1024/60  
1400 × 1050/60  
SDTV (480p)  
64  
65.3  
31.5  
31.25  
37.5  
45  
SDTV (576p)  
HDTV (720p) (50)  
HDTV (720p) (60)  
HDTV (1080i) (50)  
HDTV (1080i) (60)  
HDTV (1080p) (50)  
HDTV (1080p) (60)  
28.13  
33.75  
56.25  
67.5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
54  
 
Specifications  
Model Name  
XJ-A141/XJ-A146  
XJ-A241/XJ-A246  
XJ-A251/XJ-A256  
Brightness  
(ANSI Lumens)  
2500  
3000  
Projection System  
DLP  
Size: 0.55 inch,  
Number of Pixels: XGA  
Size: 0.65 inch,  
Number of Pixels: WXGA  
DLP chip  
×
×
(1024 768)  
(1280 800)  
Optical 2X zoom, electric focus  
Laser and LED  
Projection Lens  
Light Source  
×
COMPUTER: RGB 15-pin mini D-Sub 1 (Also used as component signal input terminal.)  
φ
×
AV: Audio (stereo) input/output and video input, 3.5 mini jack  
1
×
Terminals  
HDMI: HDMI type A terminal  
1
×
SERIAL: For RS-232C control, special terminal  
1
*
×
USB : TYPE A terminal  
1
English, French, German, Italian, Spanish, Swedish, Portuguese, Turkish, Russian,  
Chinese (Simplified), Chinese (Traditional), Korean, Japanese  
Display Languages  
* XJ-A146/XJ-A246/XJ-A256 only  
z CASIO COMPUTER CO., LTD. makes no guarantees concerning the operation or suitability of any  
USB device that you connect to the projector’s USB port.  
z Specifications are subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
55  
     
MA1207-C  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Box Network Router ME444A 530 R3 User Manual
Black Box Printer Accessories AC1020A User Manual
Black Decker Impact Driver FS1202ID User Manual
Bosch Appliances Clothes Dryer WTXD5321CN User Manual
Bosch Appliances Dishwasher SMS40A08GB User Manual
Bosch Appliances Range BOSCH GAS FREE STANDING CONVECTION RANGE User Manual
BOXLIGHT Projector MP 93i User Manual
Briggs Stratton Portable Generator 030241 0 User Manual
Carrier Heat Pump 50ZHA024 060 User Manual
Cecilware Food Warmer V107A User Manual