Black Box Printer Accessories AC1020A User Manual

JANUARY 2005  
AC1020A  
AC1021A-XMIT  
AC1021A-REC  
RGBHV Video with Stereo Audio  
Fiber Optic Transmission System  
NEED
P/N 123231 Rev.A  
© Copyright 2005. Black Box Corporation. All rights reserved.  
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)  
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746  
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
CUSTOMER  
SUPPORT  
INFORMATION  
1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax: 724-746-0746  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
Trademarks  
TRADEMARKS USED IN THIS MANUAL  
UL is a registered trademark of Underwriters Laboratories Incorporated.  
Any other trademarks used in this manual are acknowledged to be the  
property of the trademark owners.  
FCC sTaTemeNT  
FEDERAL COMMUNICATIONS COMMISSION  
AND  
CANADIAN DEPARTMENT OF COMMUNICATIONS  
RADIO FREQUENCY INTERFERENCE STATEMENTS  
This equipment generates, uses, and can radiate radio frequency energy and if not  
installed and used properly, that is, in strict accordance with the manufacturer’s  
instructions, may cause interference to radio communication. It has been tested  
and found to comply with the limits for a Class A computing device in accordance  
with the specifications in Subpart B of Part 15 of FCC rules, which are designed to  
provide reasonable protection against such interference when the equipment is oper-  
ated in a commercial environment. Operation of this equipment in a residential area  
is likely to cause interference, in which case the user at his own expense will be  
required to take whatever measures may be necessary to correct the interference.  
Changes or modifications not expressly approved by the party responsible for com-  
pliance could void the user’s authority to operate the equipment.  
This digital apparatus does not exceed the Class A limits for radio noise emission  
from digital apparatus set out in the Radio Interference Regulation of the Canadian  
Department of Communications.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les  
limites applicables aux appareils numériques de la classe A prescrites dans le Règle-  
ment sur le brouillage radioélectrique publié par le ministère des Communications  
du Canada.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
OPeraTING POINTers & TrOUBLesHOOTING  
NOm sTaTemeNT  
Normas Oficiales Mexicanas (NOM)  
Optical Fiber:  
Electrical Safety Statement  
The RGBHV with StereoAudio fiber optic transmission system is designed to operate  
INSTRUCCIONES DE SEGURIDAD  
with most multimode (MM) and single mode (SM) optical fibers.  
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de  
Remember to check the attenuation and bandwidth of the fiber optic cable. The  
system will only operate properly if these specifications fall within the range of the  
system’s loss budget.  
que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser guardadas para refer-  
encia futura.  
Troubleshooting:  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de oper-  
Multimode fiber optic cable contains an optical fiber with a light carrying “core” that  
is only .0025 inches (62.5 microns) in diameter. Single mode fiber optic cable has an  
even smaller “core”, only 00032 to .0004 inches (8-10 microns). This is smaller than  
a human hair! Therefore, any minute particles of dirt or dust can easily block the fiber  
from accepting or radiating light. To prevent this from happening, always use the  
provided dust caps whenever optical connectors are exposed to air. It is also a good  
idea to gently clean the tip of an optical connector with a lint-free cloth moistened  
with alcohol whenever dust is suspected.  
ación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca  
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que  
sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea  
The status of the VIDEO and AUDIO indicator LEDs should provide the first clue as  
to the origin of an operational failure. If these are off, it usually means that the fiber is  
broken or has too much attenuation. Next, be certain that the input and output signal  
connections are correct.  
recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá  
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser  
referido a personal de servicio calificado.  
If, after reviewing the above possibilities, the system is still not operating, please  
contact the Black Box Tech Support for further assistance  
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfi-  
era su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra  
o superficie similar puede bloquea la ventilación, no se debe colocar en libre-  
ros o gabinetes que impidan el flujo de aire por los orificios de ventilación.  
Maintenance:  
The only maintenance of the AC1020A system that can be provided by the user is to  
ascertain that the optical connectors are free of dust or dirt that could interfere with light  
transmission and that electrical connections are secure and accurate. DANGER!Always  
disconnect the transmitter power before removing the optical fiber from the unit! For  
assistance with all other repairs, please contact Black Box technical support.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor  
como radiadores, registros de calor, estufas u otros aparatos (incluyendo am-  
plificadores) que producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo  
2
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
NOm sTaTemeNT  
descrito en el instructivo de operación, o como se indique en el aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización  
del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean  
pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo  
particular atención a los contactos y receptáculos donde salen del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomen-  
daciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas  
de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea  
usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derra-  
mados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su  
desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
Ce INFOrmaTION  
Standards to which conformity is declared:  
55103-2:1997  
EN 55103-1:1997 EN  
10  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
INsTaLLaTION  
Indicator LEDs:  
The transmitter and receiver units in the A1020A system each have three integral in-  
dicator LEDs that are used to monitor the state of the unit. Their status is as follows:  
TRANSMITTER and RECEIVER:  
Power: (Green) Indicates that correct power has been applied.  
TRANSMITTER:  
Video: OFF: Indicates no video detected on the input.  
BLINKING GREEN: Indicates either H or V sync detected at the input  
but not on both.  
STEADY GREEN: Indicates both H and V sync detected on the input.  
Audio: OFF: Indicates no audio detected on the transmitter unit.  
BLINKING: Indicates audio detected on the transmitter unit.  
RECEIVER:  
Video: OFF: Indicates no video detected over fiber and, as a result, no  
video present on output.  
BLINKING GREEN: Indicates either H or V sync detected over the  
fiber but not both.  
STEADY GREEN: Indicates both H and V sync detected over the fiber  
and, as a result, video present on the output.  
Audio: OFF: Indicates no audio detected over fiber and, as a result, no active  
audio detected by the receiver unit.  
BLINKING: Indicates audio detected over fiber and, as a result,  
active audio detected by the receiver unit.  
9
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
INsTaLLaTION  
ITems INCLUded  
4. Connect the audio input signals to the transmitter stereo jack and the audio  
Depending on which product you ordered, you should have received:  
output to the receiver stereo jack.  
AC1021A-XMIT:  
Qty Description  
5. Apply power to both units. Refer to Figure 1.  
6. When power is applied, the green POWER  
LED will light, indicating the presence of  
operating power. The VIDEO LED will give  
an indication as described on Page 9.  
1
1
1
1
1
1
1
AC1021A-XMIT Transmitter  
Power Supply  
AC line cord  
User Manual  
7. The green AUDIO LED will give an indica-  
HD15M - HD15M VGA cable, 6 ft.  
3.5mm plug to 2xRCA(M) stereo audio cable, 6 ft.  
3.5mm plug to 3.5mm plug stereo audio cable, 6 ft.  
tion as stated on Page 9.  
System Connections:  
The input and output connections for the AC1020A are as follows:  
AC1021A-REC :  
Qty Description  
Audio Connector (Transmitter and Receiver): 3.5mm stereo jack  
Video Connector (Transmitter and Receiver): HD-15F connector  
1
1
1
1
1
1
1
AC1021A-REC Receiver  
Power Supply  
AC line cord  
User Manual  
HD15M - HD15M VGA cable, 6 ft.  
3.5mm plug to 2xRCA(M) stereo audio cable, 6 ft.  
3.5mm plug to 3.5mm plug stereo audio cable, 6 ft.  
Video Pin Out:  
Transmitter:  
Red  
Receiver:  
Red  
1
2
Green  
Green  
3
Blue  
Blue  
4
N/C  
N/C  
5
6
7
8
Ground  
Ground  
Ground  
Ground  
N/C  
Ground  
N/C  
N/C  
Ground  
Ground  
Ground  
Ground  
N/C  
Ground  
N/C  
N/C  
AC1020A:  
Qty Description  
1
1
2
2
2
2
2
2
AC1021A-XMIT Transmitter  
AC1021A-REC Receiver  
Power Supplies  
AC line cords  
9
10  
11  
12  
13  
14  
15  
User Manuals  
Hor. Sync In  
Vert. Sync In  
N/C  
Hor. Sync Out  
Vert. Sync Out  
N/C  
HD15M - HD15M VGA cables, 6 ft. each  
3.5mm plug to 2xRCA(M) stereo audio cables, 6 ft. each  
3.5mm plug to 3.5mm plug stereo audio cables, 6 ft. each  
8
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
AC1020A/AC1021A-XMIT/ AC1021A-REC  
GeNeraL INFOrmaTION  
GeNeraL INFOrmaTION  
Optical:  
Introduction:  
Operating Wavelength..........................1310 nm; MM or SM  
Optical Fiber ........................................50 - 62.5/125microns MM or  
8-10/125 microns SM  
The RGBHV Video with StereoAudio Fiber Optic Transmission System (AC1020A-  
V/A System) is a transmitter/receiver pair that transmits a single channel of RGBHV  
and two audio channels over one single mode or multimode fiber.  
Optical Connectors...............................ST  
The system’s all digital encoding delivers noise-free transmissions that retain all of  
their initial parameters, regardless of fiber optic cable attenuation. System operation  
may be easily monitored using integral indicator LEDs on each unit that continuously  
signify the presence of baseband video and audio signals.  
Wavelength  
1310 MM  
1310 SM  
Loss Budget (in dB)  
Distance* (in km)  
0-0.75  
0-15  
0-15  
0-35  
*Note: Distance specifications are only approximate and are not guaranteed. Oper-  
ating loss budget must not be exceeded.  
Specifications:  
Video:  
Misc:  
Operating Temperature Range .............-20 to +60 degrees C  
Operating Power ..................................9 to 24 Volts AC or DC @ 5 watts (max)  
Input Impedance...................................RGB: 75 ohms; H&V: Hi-Z  
Input Level...........................................RGB: 714 mV p-p; H&V: 3 to 5 V p-p  
H Sync Frequency Range.....................15 to 60 kHz  
V Sync Frequency Range.....................30 to 85 Hz  
Number of Video Channels..................1 RGBHV  
RGB Format Supported .......................RGB with separate H and V  
Signal Connectors................................HD-15F  
CAUTION! The transmitting element in theAC1021A-XMIT transmitter is a solid-  
state Laser Diode located in the optical connector on the unit. This device emits  
invisible infrared electromagnetic radiation which can be harmful to human eyes.  
The radiation from this optical connector, if viewed at close range without a fiber  
optic cable connected to the optical connector, may be of sufficient intensity to  
cause instantaneous damage to the retina of the eye. Direct viewing of this  
radiation should be avoided at all times.  
RGB Processing...................................24 bits, no compression or scaling  
Audio:  
Number of Audio Channels .................. 2, unbalanced  
Frequency Response ............................. +0/-0.5 dB, 20 Hz to 20 kHz  
Input Impedance.................................... >24 kOhms  
Output Impedance................................. <1 Ohm  
Maximum Audio Level......................... +10 dBu  
THD+N ................................................. 0.005%; 20 Hz to 20 kHz  
SNR (A-Weighted)................................ 95 dB  
Channel Phase Differential ................... +/-0.1o  
Crosstalk ............................................... Min. 95 dB (1kHz)  
Signal Connectors................................. 3.5mm Stereo jack  
Audio to Video Diff. Delay (skew)....... <300 uS  
INsTaLLaTION  
Installation Procedure:  
The AC1020A fiber optic transmission system for RGBHV with Stereo Audio is de-  
livered ready for immediate use. There are indicator LEDs on the units for monitoring  
purposes. The following instructions describe the typical installation procedure and  
the function of the LED indicators.  
1. ConnectthevideosourcetothevideoinputHD-15Fconnectoronthetransmitterunit.  
2. Connect the video output on the receiver unit to the HD-15F connector.  
3. Connect the fiber optic cable between the transmitter and receiver unit.  
7
6
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bertazzoni Food Warmer P24 4 00 X User Manual
Black Box Switch ACR1000A User Manual
BodyCraft Home Gym F603 User Manual
Bosch Appliances Security Camera EX36 User Manual
Bradford White Corp Water Heater BMT2H User Manual
Briggs Stratton Pressure Washer 1418 2 User Manual
Cambo Automobile Accessories LCMR5RP User Manual
Cannon Electric Pressure Cooker 10530G MK2 User Manual
Chamberlain Universal Remote 373LM User Manual
Chicago Electric Washer 96952 User Manual