Start Here
Easy Setup Instructions
Photo Printer
Important
When cleaning the exterior of the printer, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Printer” in the Quick Start Guide.
1
Prepare the Printer
2
Install the Print Head
3
Install the Ink Tanks
4
Load Printing Paper
Note
aUnpack the Printer.
aOpen the Print Head Cover. The Print
eRemove the orange protective cap from
the Print Head and discard it.
Print Head Nozzles
dSimilarly, insert the Color ink tank into
aLoad a sheet of supplied paper (Paper
For Print Head Alignment MP-101)
loaded with the printing side (whiter
side) facing UP in the Rear Tray, align
the paper stack against the guide on
the right side of the Rear Tray.
For the ink tanks compatible with this printer, refer to
the back cover of the Quick Start Guide.
Head Holder moves to the center.
the left slot.
Confirm the included items referring to the
illustration printed on the lid of the packing box
or “Included Items” in the Quick Start Guide.
aRemove the orange protective cap and
discard it.
A USB cable is necessary to connect the printer
with your computer.
Protective Cap
Ink Port
Make sure that the Paper Thickness Lever is
set to the right.
bPlace the printer on a flat and
horizontal surface, and do not place
any objects in front of the printer.
Print Head Cover
MP-101
Print Side
Remove all the shipping tapes on the outside of
the printer.
Paper Guide
Electrical Contacts
cConnect the power cord to the AC
adapter. Plug the AC adapter into the
printer, and connect the other end of
the power cord to the wall outlet.
Print Head Holder
Important
• Do not touch the electrical contacts and the ink
bUnlock the Print Head Lock Lever by
port.
Important
squeezing both tabs inward.
• Do not reattach the protective tape once you
have removed it.
If the front (innermost) part of the ink tank (A) is
sticking up, push down on the Canon logo on the
ink tank as illustrated below. Do not remove the
ink tank forcibly.
Protective Cap
Important
bInsert the Black ink tank at a slant into
• Do not touch the print head nozzles.
• Do not reattach the protective tape once you
have removed it.
the right slot.
(A)
Align the
with the
Holder.
mark on the ink tank
mark on the Print Head
fInsert the Print Head.
Align the
Print Head with the
on the Print Head Holder.
mark on the
mark
Paper Thickness Lever
Important
• Make sure the printer is turned on and the Power
lamp is flashing green.
• Make sure the Print Head Holder has moved to
the center.
Hardware setup is now complete.
Important
Next, turn over and install the software.
Do NOT connect the USB cable at this stage.
cRaise the Print Head Lock Lever until it
dOpen the Rear Tray Cover and pull out
stops.
the Paper Support completely.
Paper Support
cPress the mark on the ink tank until it
clicks into place.
Rear Tray Cover
gLower the Print Head Lock Lever
carefully.
eClose the Print Head Cover.
Caution
Paper Output Slot Cover
Do not touch internal parts other than the Print
Head Lock Lever.
Note
The Paper Output Slot Cover will open automatically.
Important
dRemove the Print Head from its
• Make sure that the ink lamp lights red.
• If the ink lamp does not light red after it is in-
serted, repeat steps band c.
package.
ePress the Power button to turn on the
printer.
• If the Print Head Cover is left open for more than
10 minutes, the Print Head Holder moves to the
right. Close and reopen the Print Head Cover to
return the holder to the center.
hPush both tabs in left to right order until
each clicks into place.
Important
Caution
Once you have installed both ink tanks, the Power
lamp will flash green. Wait for about 2 minutes,
until the Power lamp stops flashing and changes
to steady, non-flashing green and the printer has
stopped making operating noises, before proceed-
ing.
There may be some transparent or light blue ink
on the inside of the bag the print head comes in,
or the inside of the protective cap - this has no
effect on print quality. Be careful not to get ink on
yourself when handling these items.
Note
If the Alarm lamp on the printer flashes orange after
you have closed the Print Head Cover, refer to “Alarm
Lamp Flashes Orange” in “Troubleshooting” of the
Quick Start Guide.
Important
Make sure that the Print Head Lock Lever is firmly
locked into the Print Head Holder by pressing both
tabs on the Print Head Lock Lever until it clicks.
QT5-1436-V02
XXXXXXXX
© 2008 Canon Inc.
PRINTED IN THAILAND
Download from Www.Somanuals.com. All Manuals Search And Download.
|