EVM9 Extractors
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Extractor
For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for
approximately 15 minutes after the end of cooking.
Control Panel
A - Light key
B - Decrease speed key
C - Display
D - Increase speed key
E - Timer key
Fig. 1
B
A
C
D
E
To switch the extractor light on and off
Touch key A.
•
To switch on the extractor
•
•
•
Touch either key B or D. The appliance will switch on at the first speed.
To increase the speed touch key D.
To switch the extractor off, touch and hold key B for two seconds when the extractor is working at higher speeds, or
touch key B at speed one.
The intensive function
•
The extractor is equipped with an intensive function which runs for ten minutes before returning to the previous
selected speed. To activate the intensive function, touch key D at speed three. The display will blink whilst the
intensive function is on.
The timer
•
The extractor is equipped with a timer that allows the extractor to run for 15 minutes before switching off
automatically.
•
To activate the timer, touch key E. The display will flash a decimal point when the timer is on.
Please note
The timer cannot be activated when the intensive function is on.
The clean air function
•
The extractor is equipped with a clean air function that switches on the motor for ten minutes every hour at
speed one.
•
To activate the clean air function, touch key E for two seconds when the appliance is off. To return to normal
function, touch either key B or D. To switch off the clean air function, touch key E. The display C will light up
in sections whilst the motor is running, and will show the letter C during the fifty minutes when the motor is
not running.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE
EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.
2
Cleaning
You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will
scratch the surface and could erase the control panel markings.
2
1
You can clean your extractor effectively by simply using a dilute solution of water
and mild detergent and drying to a shine with a clean cloth.
Cleaning the grease filter
The grease filter should be kept clean to minimise the risk of fire.
When the display flashes alternating the speed selected with the letter A, or at
least once a month you should remove and clean the grease filter with hot soapy
water. You can also wash the grease filter in a dishwasher, ensuring that you place
it in an upright position to prevent damage from other items in the dishwasher.
After rinsing and drying, replace the filter. After the grease filter has been replaced,
the electronic memory must be reset by touching key A for approximately five
seconds, until the letter A stops flashing.
Fig. 2
To remove the grease filter follow the steps below:
1. Open the glass cover panel as shown in fig 2.
2. Pull open the handle on the grease filter as shown in fig. 2. It will release
at the handle side. Then lower the grease filter to remove it completely.
To replace the grease filter, repeat the steps in reverse.
Please note:
Cleaning the grease filter in the dishwasher may lead to discolouration. This is
normal and does not constitute a fault with the appliance.
Changing the charcoal filter (re-circulating only)
1
When the display flashes alternating the speed selected with the letter F, the
charcoal filters must be replaced. After the charcoal filter has been replaced,
the electronic memory must be reset by touching key A for approximately five
seconds, until the letter F stops flashing.
2
Fig. 3
To attach a new charcoal filter, first open the body of the extractor as shown in
figure 3. Then offer up the charcoal filter into the frame as shown in figure 4 until
it locks into place. Repeat with the other charcoal filter, then close the body of the
extractor..
Fig. 4
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Light
IMPORTANT: DO NOT PERFORM MAINTENANCE
OR CLEANING OF THE EXTRACTOR WITHOUT FIRST
SWITCHING OFF THE ELECTRICITY SUPPLY.
DO NOT CHANGE THE LIGHT BULB IMMEDIATELY
AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO
COOL BEFORE REMOVING IT.
Carefully prise the bulb from the extractor using a small,
flat-bladed screwdriver. Refit the new bulb taking care not
to touch the glass (Fingerprints will lead to premature failure
of the bulb).
Fig. 5
Do not touch bulbs or adjacent areas during or straight after
prolonged use of the lights.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Mains Electricity Connection
THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED
WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE.
We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will
comply with the I.E.E. and local regulations.
DOUBLE POLE SWITCHED
The wires in the mains lead of this appliance are coloured in accordance with the
FUSED SPUR OUTLET
following code:
BLUE = NEUTRAL, BROWN = LIVE.
As the colours of the wires in the mains lead for the appliance may not correspond
with the coloured markings identifying the terminals connecting to the fused spur,
proceed as follows:
•
•
The wire which is coloured blue must be connected to the terminal marked N
(Neutral), or coloured black.
The wire which is coloured brown must be connected to the terminal marked
L (Live), or coloured red.
USE A 3 AMP FUSE
NOTE: USE A 3A FUSE
Assembly and electrical connection should be carried out by competent personnel.
When installing this product we recommend you seek the help of another individual.
IMPORTANT: THIS APPLIANCE IS A CLASS II APPLIANCE (DOUBLE INSULATED) AND IS NOT INTENDED TO
BE EARTHED. DO NOT FIT AN EARTH LEAD TO THIS EXTRACTOR.
Do not mount the isolation switch behind the chimney section. It is a requirement that you must be able to isolate the
extractor from the mains electrical supply after installation.
This appliance is intended to be connected to the mains electrical supply by means of an isolation switch and fused spur
and is intended to be protected by a 3A fuse. The use of a 13A fuse can cause damage to the internal wiring in the event
of a fault, and may also invalidate the warranty.
Electrical Information
Mains electrical voltage: 230 – 240Vac, 50Hz
Total rated power consumption:
290W
Troubleshooting
If your extractor is not working:
1.
Check that the mains supply has not been switched off.
2. Check that the fuse in the spur has not blown.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Your extractor can be used to filter and recycle the air within
your kitchen, or to extract the air outside. When extracting air
to the outside, the unit can be vented as shown in the diagram
below. Note that we recommend the use of ducting with a
diameter of 150mm. Ducting with diameters of 100mm or
120mm may be used, but performance will be reduced.
When installing this appliance over a CDA hob, the clearance
between the extractor and the hob must be equal to or
exceed 450mm. This instruction overrides the instructions
supplied with the CDA hob. (The height should be measured
from the top of the hotplates or burners)
Where the extractor is to be installed above a non-CDA hob,
the instructions supplied with the hob may dictate that the
height required above the hob is greater than 450mm.
Fig. 6
IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED
WITH THE HOB, THE MINIMUM DISTANCE BETWEEN
THE HOB AND EXTRACTOR MUST BE AT LEAST
760mm.
A
Fitting your extractor to the wall
Before commencing the installation open front panel. Hold
the panel as shown in figure 8 and lift upwards and out.
min 45cm
B
Fig. 7
1
2
Fig. 8
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting your extractor to the wall
Next, remove the top cover by loosening the screws (b),
closing the front panel and then lifting the cover off.
The extractor is mounted using four screws. Ensure that
the wall fixings and screws are suitable for the wall material.
Mark the positions of the four holes on the wall, according
to (fig 11.)
Fig. 9
Fig. 10
460
178
112.5
+ 450mm for CDA Hob
Fig. 11
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting your extractor to the wall
Insert the 4 wall plugs in to the holes and fix 2 screws in
the top holes so that they are protruding from the wall by
approx 5mm (fig 12).
Next, lift the hood onto the 2 screws as shown in (fig12).
Secure the top two screws and fix the hood into position
using screws inserted into the 2 lower holes (fig 13). The
extractor is now secured to the wall.
Fig. 12
Fig. 13
Using the extractor as a
recirculation device
Refit the top cover and grill as below before proceeding
to fit the charcoal filter – locate each filter onto the motor
housing spigot and rotate to lock into position.
Fig. 14
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the extractor as an
extraction device
Work out the required height of the optional chimney for
your ceiling and mount the chimney fixing bracket as shown
in the (fig 16), then secure the chimney as shown in (fig 17a).
Finally, locate the chimney to the body of the extractor as
shown in (fig 18).
Fig. 16
Fig. 17
Fig. 18
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Download from Www.Somanuals.com. All Manuals Search And Download.
|