INSTRUCTION MANUAL
VC-C4
COMMUNICATION CAMERA
f:4-64mm 1:1.4-2.8
Please read this instruction manual carefully before operation.
Be sure to read the “aSafe Use of Equipment” section before
using this equipment. Store this manual in a readily accessible
location for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
a Safe Use of Equipment
An exclamation point, within a triangle, is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the equipment.
a Important Warnings
a CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The serial number of this equipment may be found on the back of the camera
head. No others have the same serial number as yours.
You should record the number and other vital information here and retain this
book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase
Dealer Purchased from
Dealer Address
Dealer Phone No.
Model No. VC-C4 or VC-C4R
Serial No.
a Important Operational Instructions
a WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
a CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
FDA regulation
This communication camera has not been evaluated by the Food and Drug
Administration (FDA) for use as a medical device. When incorporated into a system
with medical applications, FDA regulations may apply. Therefore, please consult
your legal advisor to determine whether FDA regulations apply.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
a Safe Use of Equipment
FCC NOTICE
PT-V4N/PT-V4NR
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part
15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the manual. If such changes or modifications should be made, you
could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516) 328-5600
IC NOTICE
This product does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the Interference-causing equipment standard entitled
‘Digital Apparatus’, ICES-003 of the Industry Canada.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
a Safe Use of Equipment
a IMPORTANT SAFETY INSTRUCTIONS
In these safety instructions, the word
“equipment” refers to the Canon
communication camera VC-C4/VC-C4R and
all its accessories.
the equipment. An equipment and cart
combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the equipment and
cart combination to overturn.
1. Read Instructions - All the safety and
operating instructions should be read
before the equipment is operated.
9. Power Sources - The PA-V16 AC adapter
should be operated only from the type of
power source indicated on the marking
label. If you are not sure of the type of
power supply to your home, consult your
equipment dealer or local power
company.
2. Retain Instructions - The safety and
operating instruction should be retained
for future reference.
3. Heed Warnings - All warnings on the
equipment and in the operating
instructions should be adhered to.
Regarding other power sources such as
battery power, refer to instructions in this
manual.
4. Follow Instructions - All operating and
maintenance instructions should be
followed.
10. Polarization - The PA-V16 AC adapter is
equipped with a polarized 2-prong plug
(a plug having one blade wider than the
other).
5. Cleaning - Unplug this equipment from the
wall outlet before cleaning.
The 2-prong polarized plug will fit into the
power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug.
If the plug still fails to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the
polarized plug.
Wipe the equipment with a clean soft
cloth. If necessary, put a cloth in diluted
neutral detergent and wring it well before
wiping the equipment with it. Finally, clean
the equipment with a clean dry cloth. Do
not use benzene, thinner or other volatile
liquids or pesticides as they may damage
the product’s finish. When using
chemically-treated cleaning cloths,
observe those precautions accordingly.
11. Power Cord Protection - Power cords
should be routed so that they are not likely
to be walked on or pinched by items
placed upon or against them. Pay
particular attention to plugs and the point
from which the cords exit the equipment.
6. Accessories - Do not use accessories not
recommended in this manual as they may
be hazardous. Always use specified
connection cables. Connect devices
correctly.
12. Outdoor Antenna Grounding - If an
outside antenna is connected to the
equipment, be sure the antenna is
grounded so as to provide some
protection against voltage surges and
built-up static charges. Section 810 of the
National Electrical Code, ANSI/NFPA
No.70-1984, provides information with
respect to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna discharge unit,
size of grounding conductors, location of
7. Water and Moisture - Hazard of electric
shock - Do not use the equipment near
water or in rainy/moist situations. Do not
put a heater near this equipment.
8. Placing or Moving - Do not place on an
unstable cart, stand,
tripod, bracket or table.
The equipment may
fall, causing serious
injury to a child or adult,
and serious damage to
5
Download from Www.Somanuals.com. All Manuals Search And Download.
a Safe Use of Equipment
antenna discharge unit, connection to
grounding electrodes, and requirements
for the grounding electrode. See figure 1.
17. Servicing - Do not attempt to service this
equipment yourself as opening or
removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified personnel.
fig-1
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
18. Damage Requiring Service - Disconnect
this equipment from the wall outlet and
all power sources including batteries, and
refer servicing to qualified service
personnel under the following conditions.
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE
UNIT (NEC
GROUNDING
CLAMP
SECTION 810-20)
a. When the power-supply cord or plug is
damaged.
GROUNDING
CONDUCTORS
(NEC SECTION
810-21)
ELECTRIC
SERVICE
EQUIPMENT
b. If any liquid has been spilled onto, or
objects have fallen into, the equipment.
GROUNDING CLAMPS
c. If the equipment has been exposed to
rain or water.
POWER SERVICE
GROUNDING ELECTRODE
SYSTEM
(NEC ART 250. PART H)
NEC — NATIONAL ELECTRIC CODE
d. If the equipment does not operate
normally even if you follow the
operating instructions. Adjust only
those controls that are covered by the
operation instructions. Improper
adjustment of other controls may result
in damage and will often require
extensive work by a qualified
technician to restore the equipment to
its normal operation.
13. Lightning - For added protection of this
equipment during a lightning storm, or
when it is left unattended and unused for
long periods of time, disconnect it from
the wall outlet and disconnect the
antenna. This will prevent damage to the
equipment due to lightning and power-line
surges.
e. If the equipment has been dropped or
the cabinet has been damaged.
14. Power Lines - An outside antenna system
should not be located in the vicinity of
overhead power lines or other electric
light or power circuits, or where it can fall
into such power lines or circuits. When
installing an outside antenna system,
extreme care should be taken to keep
from touching such power lines or circuits
as contact with them might be fatal.
f. When the equipment exhibits a distinct
change in performance. This indicates
a need for service.
19. Replacement Parts - When replacement
parts are required, be sure the service
technician has used replacement parts
that are specified by Canon or that have
the same characteristics as the original
part. Unauthorized substitutions may
result in fire, electric shock or other
hazards.
15. Overloading - Do not overload wall outlets
and extension cords as this can result in
a risk of fire or electric shock.
16. Object and Liquid Entry - Never push
objects of any kind into this equipment
through openings as they may touch
dangerous voltage points or short out
parts that could result in a fire or electric
shock. Be careful not to spill liquid of any
kind onto the equipment.
20. Safety Check - Upon completion of any
service or repairs to this equipment, ask
the service technician to perform safety
checks to determine that the equipment
is in safe operating order.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
a Safe Use of Equipment
21. Do not install the equipment in the
following locations as this can cause a
fire or electric shock:
- When the batteries are used up, or
when the equipment will not be used
for an extended period, remove the
batteries.
- Hot locations
- When replacing the batteries, always
replace both batteries, and do not use
different types of batteries together.
- Close to a fire
- Very humid or dusty locations
- Locations exposed to direct sunlight
- Locations exposed to salt spray
- Ensure that the + and - terminals are
correctly positioned when you load the
batteries.
- Close to flammable solvents (alcohol,
thinners, etc.)
- If any soiling or leakage of the internal
battery fluid occurs, thoroughly clean
the soiling or leaked fluid with water.
22. When any of the following occurs,
immediately switch OFF the equipment,
unplug it from the main power supply and
contact your nearest Canon supplier. Do
not continue to use the equipment as this
can cause a fire or electric shock.
- The equipment emits any smoke, heat,
abnormal noise, or unusual odor.
- A metal object falls into the equipment.
- The equipment is damaged in some
way.
23. Please observe the following when using
the equipment. Failure to do so can result
in a fire or electric shock.
- Do not use flammable sprays near the
equipment.
- Do not subject the equipment to strong
impacts.
24. Please observe the following when
handling the batteries. Failure to do so
can result in the batteries bursting or
emitting heat, sparks or corrosive fluid.
- Do not throw the batteries into a fire,
and do not heat, short-circuit or attempt
to disassemble the batteries.
- Do not attempt to recharge the
batteries.
- Do not use batteries other than those
specified for use with the equipment.
25. Please observe the following when
handling the batteries. Failure to do so
may result in the batteries bursting or
emitting heat, sparks or corrosive fluid.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
a Safe Use of Equipment
Maintenance
Cleaning the Equipment
1. Unplug the AC adapter from the wall outlet.
2. Carefully wipe the equipment with a soft cloth that has been moistened
with water or a mild detergent.
WARNING
Do not use flammable solvents such as alcohol, benzene or thinners.
The use of such substances can cause a fire or electric shock.
3. Wipe with a dry cloth.
4. When you have finished, plug the AC adapter back in to the wall
outlet.
Cleaning the Lens
Use a commercially available lens cleaner to remove any soiling from the lens.
■ The auto-focus may not function correctly if the surface of the lens is dirty.
■ Scratches on the surface of the lens will cause image defects.
Icons Used in This Instruction Manual
Indicates important information that must be observed or actions that are
prohibited during an operation. These notes must be read to prevent
NOTE
possible faults or damage to the equipment.
Indicates supplementary information or a reference to an operation. Users
are advised to read these memos.
MEMO
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
a Safe Use of Equipment .......................................................................................... 3
a Important Warnings .................................................................................... 3
a Important Operational Instructions ........................................................... 3
a IMPORTANT SAFETY INSTRUCTIONS...................................................... 5
Maintenance .................................................................................................... 8
Icons Used in This Instruction Manual............................................................... 8
Before You Use the Product .................................................................................... 10
Checking the Accessories ........................................................................... 10
Nomenclature ................................................................................................ 10
Camera ...................................................................................................................... 10
Wireless Controller .................................................................................................... 11
Installing the Product ................................................................................... 12
Connecting the Components ....................................................................... 13
Turning the Power ON and OFF................................................................... 14
LED Displays and the Camera Status ....................................................................... 14
Loading the Batteries into the Wireless Controller ................................... 15
Operable Range of the Wireless Controller ............................................................... 15
Controlling the Camera from the Wireless Controller ........................................... 16
Changing the Camera Head Angle (pan/tilt/home position) ..................... 16
Range of Camera Head Movement ........................................................................... 16
Zooming In/Out (TELE/WIDE)....................................................................... 17
Focusing (FOCUS) ........................................................................................ 18
Adjusting the Brightness (BRIGHT) ............................................................ 19
Storing a Preset Camera Position ............................................................... 20
Switching the Camera ON and OFF............................................................. 21
Camera Settings ....................................................................................................... 22
Buttons Used to Specify the Settings ......................................................... 22
Setting Menu Description .......................................................................................... 22
Setting the Clock ........................................................................................... 23
Entering Characters ...................................................................................... 24
Selecting Display/Hide Clock and Text ....................................................... 24
Setting the Camera Head Movement Speed and Pan Operation .................... 25
Setting the Range of Camera Head Movement .......................................... 26
Setting the AE................................................................................................ 27
VC-C1 Mode and VC-C3 Mode Setting Menu ............................................. 27
RS-232C Settings .......................................................................................... 28
ID Mode ...................................................................................................................... 29
Setting the ID Number .................................................................................. 29
Selecting the Camera to be Controlled ....................................................... 30
Cancelling ID Mode ....................................................................................... 31
Troubleshooting ........................................................................................................ 32
Factory Default Settings........................................................................................... 34
Specifications ............................................................................................................ 35
Appendix A ................................................................................................................ 36
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Use the Product
Checking the Accessories
Before you install the Product, check that all the items shown below are included in your product
package. If any of these items is missing, contact your Canon dealer.
or
VC-C4 camera
VC-C4R camera
Wireless Controller WL-V5
AC adapter PA-V16
AC cable
Pin cable
● 2 AA-size manganese batteries
● Instruction Manual
● Warranty Card
■ Optional Product
● Wide-angle Converter WL-37
Cannot be used on the VC-C4R (→ P.13).
Nomenclature
Camera
VC-C4
VC-C4R
LED
Camera head
(Front)
Base
Wireless controller
sensor
Base
LED
Wireless controller
sensor
Camera head
RS-232C input terminal
RS-232C output terminal
VIDEO OUT terminal
S VIDEO OUT terminal
(Rear)
DC IN 13V terminal
RS-232C input terminal
RS-232C output terminal
VIDEO OUT terminal
S VIDEO OUT terminal
DC IN 13V terminal
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Use the Product
Wireless Controller
Camera ON/OFF button (→ P.21)
Switches the camera on and off.
ZOOM button (→ P.17)
BRIGHT button (→ P.19)
Adjusts the brightness of the
image on the monitor.
• +:Brightens the image.
• – :Darkens the image.
Increases or decreases the size of the
subject on the monitor screen.
• T :Enlarges the subject (zoom in).
• W :Shrinks the subject (zoom out).
BRIGHT
ZOOM
T
W
Camera control button (→ P.16, 22)
Used to change the camera head angle
and to move the on-screen cursor.
SET/OK button (→ P.20, 22)
Used to store preset positions.
Can also be used to proceed to
the next level when specifying
settings in a setting menu.
HOME
•
V
< > : Move the camera head up,
down, left and right
respectively.
SET/OK
CANCEL
^
AF
1
4
7
2
3
6
9
• HOME : Moves the camera head to the
center.
MF
5
8
FOCUS button (→ P.18, 19)
Adjusts the focus.
• AF :Switches to auto-focus.
• MF :Focus is fixed.
∞
CANCEL button (→ P.20, 22)
Cancels registration of a preset camera
position. Also cancels a setting selected
in a setting menu and returns you to the
previous level.
0
ON SCREEN Fn
ID
MENU
•
:Lengthens the focal
distance.
•
:Shortens the focal
distance.
Number buttons (→ P.20, 30)
Used to store and restore preset
positions, and to select the camera when
multiple cameras are used. The * and
# buttons are not used.
WL-V5
WIRELESS CONTROLLER
ON SCREEN button (→ P.24)
Displays or hides the date, time
and text.
MENU button (→ P.22)
Used to display the MAIN MENU and to
exit a setting menu.
Fn button
Not used.
ID button (→ P.30)
Used to control multiple cameras
individually. When the cameras are
switched off, pressing this button begins
individual camera control.
Battery cover
See page 15 for information
on loading the batteries.
Whenever possible, switch the camera off when it is not in use (→ P.21) as this
reduces power consumption. If the camera will not be used for an extended period,
unplug the AC adapter from the wall outlet (→ P.14). If you turn the power off, the
date and time will be cleared.
MEMO
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Use the Product
Installing the Product
VC-C4 Installation
VC-C4R Installation
Install in a flat and stable location.
Firmly tighten the 2 screws (not supplied).
VC-C4
MUNICATIO
COM
N
CAM
ERA
Mounting plate
VC-C4R
Screw
Screw
(Installation)
• Distance between tapped holes: 114 mm (4 1/2 in.)
• Tapped hole diameter: 6 mm (7/32 in.)
• Mounting plate thickness: 1 mm (1/16 in.)
WARNING
Install the camera securely.
● When installing the camera on the ceiling, contact your Canon dealer.
● When installing the camera on the ceiling, check that the ceiling is strong enough to
bear the weight of the camera including the installation bracket. Installation in a weak
location could result in the camera falling and causing serious injury.
● At least once a year, check for looseness in the camera installation mount. (If the
optional wide-angle converter is used, check the converter mount also.)
The permissible camera installation angles are ±20° from the horizontal. (±15°
when the optional wide-angle converter is used.)
NOTE
Using a Tripod
The screw mount for a tripod is located in the center of the underside of the camera.
● Do not overtighten the mounting screw.
If excessive force is used to tighten the
mounting screw, camera head movement may
be impeded, or other malfunctions may result.
30 mm
Less than
6.0 mm
(1/4 in.)
(1 3/16 in.)
or wider
NOTE
Mounting
screw
●
Always use a tripod mounting screw that is less
than 6.0 mm (1/4 in.) in length. The use of screws
6.0 mm (1/4 in.) long or longer could damage
the camera. Also, the tripod seat used should
be at least 30 mm (1 3/16 in.) in diameter.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Use the Product
Using the Wide-angle Converter
The optional Wide-angle Converter WL-37 can be used to provide wide-angle shots (approx.
0.74× the normal focal distance).
Mount the wide-angle converter correctly so that it is level and fitted securely onto the camera.
When mounted correctly, the wide-angle converter should turn roughly 3 times before stopping.
Wide-angle Converter
WARNING
The Wide-angle Converter WL-37 is designed specifically for the VC-C4 and cannot
be used on the VC-C4R. If the converter is used on the VC-C4R, the mount will gradually
loosen and the converter will fall off the camera.
● The camera may not operate correctly if a wide-angle converter other than the
WL-37 is used.
NOTE
● The permissible range of camera installation angles with the wide-angle
converter mounted on the camera is ±15° from the horizontal.
Connecting the Components
(Rear of camera)
COMM
f:4-64m
U
m
NIC
1
A
TION
:1.4-2.8
C
AMERA
To RS-232C-IN
AC cable
DC IN 13V
S
VIDEO OUT VIDEO OUT
OUT RS232C
IN
Another
VC-C4/VC-C4R
RS-232C cable
RS-232C cable
To RS-232C terminal
PC
Pin cable
To VIDEO IN terminal
AC adapter
Monitor
S-VIDEO cable
To S-VIDEO IN terminal
No S-VIDEO or RS-232C cable is supplied with the camera. Consult your dealer
for information on suitable RS-232C cables for your computer.
MEMO
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Use the Product
Turning the Power ON and OFF
The VC-C4/VC-C4R camera itself does not have a power switch. You can switch the camera on
by plugging the AC adapter into a wall outlet. When power to the camera is switched on, the
LED on the camera turns green. If the monitor is switched on, an image appears on the screen.
Camera
to AC outlet
Monitor
AC adapter
AC cable
● Whenever you turn the power on, first press any button on the wireless
controller. This initializes the camera head position. Initialization takes several
NOTE
seconds. During initialization, the LED on the camera flashes green (at 1-second
intervals).
● Never touch the camera head during initialization as this could prevent successful
initialization and cause faults.
● Wait at least five seconds before turning the power back on after shutting it off.
Turning it on too quickly may result in a malfunction. Observe the precautions
given in “a Safe Use of Equipment/a IMPORTANT SAFETY INSTRUCTIONS”
(→ P.5–7).
LED Displays and the Camera Status
LED Display
Camera Status
Green
Camera is on. (→ P.21)
At 0.1-sec. intervals
Wireless controller button being used.
Storing or restoring a preset (→ P.20), or displaying
a setting menu. (→ P.22)
Blinking green
At 0.5-sec. intervals
At 1-sec. intervals
Camera head position initialization in progress.
Individual camera operation in progress and this camera
Orange
is not selected. (→ P.30)
Camera is not selected for individual operation and is being
At 0.1-sec. intervals
At 0.5-sec. intervals
controlled from the wireless controller. (→ P.30)
Blinking orange
The camera is being selected or deselected for
individual operation. (→ P.30)
Red
Off
Camera is off. (→ P.21)
Power is off.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Use the Product
Loading the Batteries into the Wireless Controller
The wireless controller requires two AA-type batteries.
1. Remove the battery cover.
2. Insert the batteries.
■ Taking care that the poles (+ and -) are
correctly positioned.
3. Replace the battery cover.
WARNING
Observe the following precautions when handling batteries.
Failure to do so could result in the batteries bursting or emitting heat, sparks or corrosive fluid.
● Do not throw the batteries into a fire, and do not heat, short-circuit or attempt
to disassemble the batteries.
● Do not attempt to recharge the batteries.
Operable Range of the Wireless Controller
Use the wireless controller within the range described below, facing it toward the sensor for the
wireless controller. The operable range of the wireless controller varies depending on the amount
of charge remaining in the batteries and interference from other objects. (This applies equally to
the VC-C4R.)
5 m
(16 ft. 4 7/8 in.)
90°
30°
90°
30°
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Camera from the Wireless Controller
While the wireless controller buttons are being used, the LED on the camera blinks green (at
0.1-second intervals) (→ P.14).
Changing the Camera Head Angle (pan/tilt/home position)
Use the procedures below to change the camera head angle.
To move the camera head left and right (pan)
Press the 4 and 6 buttons.
BRIGHT
ZOOM
T
■ When pointing the remote control in the direction of the camera
and using it, the image on the monitor moves in the direction of
the arrow on the button pressed, and the camera head moves
in the oppsite direction.
W
HOME
SET/OK
CANCEL
When DIRECTION MIRROR (→ P.25) is set to ON, the camera
head moves in the direction of the arrow on the button pressed.
■ Holding the button down increases the speed of camera head
movement as shown below.
AF
MF
1
4
7
2
3
6
9
5
8
0
Low speed → Medium speed → High speed
ON SCREEN Fn
ID
MENU
To move the camera head up and down (tilt)
Press the 8 and 5 buttons.
■ Holding the button down increases the speed of camera head
movement as shown below.
Low speed → Medium speed → High speed
To move the camera head to the Home position
Press the h button.
■
This moves the camera head to the center position at high speed.
Do not attempt to manually change the camera head angle.
If the camera head is accidentally moved, either by hand or by
being struck by an object, always press the h button. The
deviation from the position that the camera memorizes will be
corrected and the operation will be back in order.
NOTE
Range of Camera Head Movement
The figures below show the range of camera head movement from a horizontal position. The
default range of upward movement for the VC-C4 is 30°, but the range can be set to 90°
(→ P.26).
30°
100°
100°
10°
170°
30°
170°
VC-C4
VC-C4R
90°
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Controlling the Camera from the Wireless Controller
Zooming In/Out (TELE/WIDE)
The zoom function increases (zoom in) and decreases (zoom out) the size of the subject on the
monitor screen.
To zoom in (TELE):
BRIGHT
ZOOM
Press the t side of the button.
T
■ Holding down the button changes the rate of zoom as shown
W
below.
Slow
Fast
HOME
SET/OK
CANCEL
AF
1
4
7
2
3
6
9
MF
5
8
∞
0
ON SCREEN Fn
ID
MENU
To zoom out (WIDE):
Press the w side of the button.
■ Holding down the button changes the rate of zoom as shown
below.
Slow
Fast
Focusing Range
At some zoom settings, the camera may not be able to focus on the subject.
MEMO
Changes in the distance from the camera to the subject
Effective focusing range
1 m (39 3/8 in.)
Distance
80 cm (31 1/2 in.)
1 cm
(13/32 in.)
Zoom position
W end of zoom
Down to approx. 1cm (13/32 in.)
T end of zoom
Up to approx. 80 cm (31 1/2 in.)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Camera from the Wireless Controller
Focusing (FOCUS)
This section describes how to focus on the subject. The VC-C4/VC-C4R has an auto-focus
mode, in which the camera automatically focuses on the subject, and a manual focus mode, in
which the operator can adjust the focus by hand.
To use autofocus mode
BRIGHT
ZOOM
Press the a button.
T
■ The camera focuses automatically.
W
HOME
SET/OK
CANCEL
AF
1
4
7
2
3
6
9
MF
5
8
∞
0
ON SCREEN Fn
ID
MENU
Subjects not suitable for auto-focus
The camera may have difficulty focusing automatically on subjects of the type
shown below. Use the manual focus mode for such situations.
NOTE
Subjects with little or
no contrast (a white
wall, for example)
Angled subjects
Highly reflective
subjects
Horizontally striped
subjects
Insubstantial subjects
such as flames or
smoke
Subjects seen through
glass
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Camera from the Wireless Controller
To fix the focus
Press the n button.
BRIGHT
ZOOM
T
■ This switches auto-focus off and fixes the focus.
W
To focus on nearby subjects
HOME
SET/OK
CANCEL
Press the r button.
■ This enables switching the camera to manual focus mode while
moving the focal point closer to the camera.
■ Holding the button down moves the focal point closer to the
camera.
AF
1
4
7
2
3
6
9
MF
5
8
∞
0
ON SCREEN Fn
ID
MENU
To focus on distant subjects
Press the e button.
■ This enables switching the camera to manual focus mode while
moving the focal point further from the camera.
■ Holding the button down moves the focal point further away
from the camera.
■ At some zoom settings, the camera may not be able to focus
on the subject (→ P.17).
Adjusting the Brightness (BRIGHT)
This function brightens or darkens the image on the monitor. When the camera is switched on,
the brightness is set to the Normal level.
To brighten or darken the image
Press the z side of the button to brighten the image and
BRIGHT
ZOOM
T
the x side to darken the image.
■ The image gradually brightens (or darkens) while the button is
held down.
W
HOME
Darker
Normal brightness
Brighter
SET/OK
CANCEL
AF
1
4
7
2
3
6
9
MF
5
8
∞
■ The Normal brightness setting corresponds to setting [5] in the
AE REFERENCE screen (→ P.27). The brightest setting is [10]
and the darkest setting is [1].
0
ON SCREEN Fn
ID
MENU
■ It may not be possible to adjust the brightness when the area
around the subject is extremely dark. In this event, use lighting
to brighten the area around the subject.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Camera from the Wireless Controller
Storing a Preset Camera Position
This section describes how to store a camera head angle, zoom position and brightness level.
Up to nine (1 to 9) preset positions can be stored. Switching the power off or the camera off does
not erase the stored preset positions.
To store a position
BRIGHT
ZOOM
1. Set the camera head angle, zoom position and brightness.
T
■ The focus setting is not stored.
W
2. Press the s button.
HOME
■ The LED on the camera blinks green (at 0.5-second intervals).
■ Press the c button again to cancel the operation.
SET/OK
CANCEL
AF
1
4
7
2
3
6
9
MF
5
8
∞
3. Press a button from 1 to 9.
0
■ When the position has been stored, the LED on the camera
stops blinking and remains green.
ON SCREEN Fn
ID
MENU
■ Any existing preset information is overwritten.
To restore a preset position
Press a button from 1 to 9.
■ The VC-C4/VC-C4R returns to the stored camera head angle,
zoom position and brightness level.
● During preset operations, the camera pans and tilts at the speeds set for pan/
tilt operation in the setting menu. When the “AUTO” setting is selected, the
head moves at the maximum speed (→ P.25).
MEMO
● Stored preset position information can only be overwritten. Stored preset
positions cannot be erased. However, the preset position is cleared if the
COMMAND mode is changed.
● If the camera is in manual focus mode, the focus may be incorrect when a
preset position is restored. In this event, set the camera to auto-focus mode or
focus the camera manually.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Camera from the Wireless Controller
Switching the Camera ON and OFF
The camera is switched on and off by using the p (camera ON/OFF) button on the wireless
controller.
To switch the camera off
With the wireless controller in range of the camera, press
the p button.
BRIGHT
ZOOM
T
W
■ The image disappears and the LED on the camera turns red
(camera OFF). The camera will now respond only to the p
button or i button on the wireless controller.
HOME
SET/OK
CANCEL
To switch the camera on
AF
1
4
7
2
3
6
9
MF
5
8
In the status of camera OFF, press the p button.
■ An image appears on the monitor screen and the LED on the
camera turns green (camera ON). The camera will now respond
to all operations performed from the wireless controller.
■ Even if the camera is off, when you press the i button the
LED on the camera blinks orange and you can begin ID mode
operation (→ P.30).
∞
0
ON SCREEN Fn
ID
MENU
● Even if you switch the camera off, electric current will continue to flow to the
camera. However, the power of the camera will not be turned off (→ P.14).
Accordingly, even if you switch the camera off, stored preset positions, the date
and the time are not cleared.
MEMO
● Whenever possible, switch the camera off when it is not in use as this reduces
power consumption. If the camera will not be used for an extended period,
unplug the AC adapter from the wall outlet. If you turn the power off, the date
and time will be cleared.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
Set and display the clock and text, and specify camera operation settings.
Buttons Used to Specify the Settings
The wireless controller buttons shown below are used for the setting.
58 buttons: Move the cursor up and down.
BRIGHT
ZOOM
6 button
: Moves the cursor right. Also proceeds to the next
setting level.
T
W
4 button
: Moves the cursor left.
HOME
SET/OK
CANCEL
c button
: Returns to the previous screen without confirming
any settings.
AF
1
4
7
2
3
6
9
MF
5
8
∞
s button
m button
: Confirms the settings and proceeds to the next
setting level.
0
ON SCREEN Fn
ID
MENU
: Displays or hides the setting menu. While the
setting menu is displayed, the LED on the camera
blinks green (at 0.5-sec intervals).
o button
: Displays or hides displays such as the clock and
text (→ P.24). If no date or time is set, the date
setting (01.JAN.’00) and time setting (00.00.00AM)
blink. Note that this button is disabled when the
camera is in the setting menu.
Setting Menu Description
Press the m button to display the setting menu.
Cursor
M
AI
NU
ISPLAY
N
M
E
NU
SET
M
E
SET MENU
:
Use this menu to specify the settings used to control
the camera from a PC or another unit via the RS-232C
input terminal (→ P.28).
D
M
E
NU
CA
M
E
R
A
MENU
DISPLAY MENU : Use this menu to set the clock and to enter the
characters (→ P.23, 24).
NEXT SET BACK CANCEL
CAMERA MENU: Use this menu to change the settings for camera
head pan and tilt speed, the range of camera head
movement, and the camera head brightness level
(
→
P.25–27).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
Setting the Clock
Use the procedure below to set the date and time. You can also select your preferred TIME
STYLE and DATE STYLE settings.
or
M
AI
NU
ISPLAY
N
M
E
NU
D
ISPLAY
M
E
NU
D
ATE
&
T I
ME
SETTING
01. JA
00 : 00: 00A
S
SET
M
E
D
ATE
D
D
&
ISPLAY
ISPLAY
ON
ON
SET
SET
D
ATE
N
.
’00
or
T
I
ME
D
MENU
DATE
TI
ME
SETTINGS. .
T
I
ME
M
/
CA
M
E
R
A
M
E
NU
TXT
D
ISPLAY
ON
T
I
M
E
STYLE
ATE STYLE
EXT SET BACK CA
A
M
P
M
TXT SETTINGS. .
/
/
D
DD MM YY
CEL
NEXT SET BACK CA
NCEL
NEXT SET BACK CA
N
CEL
N
N
D
ATE
&
T I
ME
SETTING
01. JA
00 : 00: 00A
S
D
ATE
&
T I
ME
SETTING
S
D
ATE
&
T I
ME
SETTING
S
D
ATE
&
T I
ME
SETTING
S
SET
SET
D
ATE
N
.
’00
or
SET ATE
D
01. JA
N
.
’00
SET ATE
D
12. JUN
.
’00
SET ATE
D
12. JUN
.
’00
T
I
ME
M
/
T
I
M
E
STYLE
ATE STYLE
EXT SET BACK CA
A
M
P
M
/
/
D
DD MM YY
CEL
N
N
SET SET CA
N
CEL CA
NCEL
SET SET CA
N
CEL CA
NCEL
SET SET CANCEL CANCEL
or
Set minutes and seconds likewise.
D
ATE
&
T I
ME
SETTING
01. JA
00 : 00: 00A
S
D
ATE
&
T I
ME
SETTING
S
D
ATE
&
T I
ME
SETTING
S
D
ATE
&
T I
ME
SETTING
S
or
SET
SET
D
ATE
N
.
’00
T
I
ME
M
SET
T
I
ME
00 : 00: 00A
M
SET
T
I
ME
01 : 30: 00A
M
SET
T
I
ME
01 : 30: 00P
M
/
T
I
M
E
STYLE
ATE STYLE
EXT SET BACK CA
A
M
P
M
/
/
D
DD MM YY
CEL
N
N
SET SET CA
N
CEL CA
NCEL
SET SET CA
N
CEL CA
NCEL
SET SET CANCEL CANCEL
or
D
ATE
&
T I
ME
SETTING
01. JA
00 : 00: 00A
S
D
ATE
&
T I
ME
SETTING
S
or
SET
SET
D
ATE
N
.
’00
T
I
ME
M
Example of screen
displayed when 24H and
YY/MM/DD are selected.
/
/
T
I
M
E
STYLE
ATE STYLE
EXT SET BACK CA
A
M
P
M
T
I
M
E
STYLE
24H
/
AM
P
M
/
D
DD MM
YY
N
N
CEL
SET SET CA
N
CEL CANCEL
D
ATE
&
T I
ME
SETTING
S
or
SET
SET
D
ATE
’00. 06. 12
13 : 30: 00
T
I
ME
T
I
M
E
STYLE
ATE STYLE
EXT SET BACK CA
24H
D
ATE
&
T I
ME
SETTING
S
D
ATE
&
T I
ME
SETTING
S
/
/
D
YY MM DD
or
SET
SET
D
ATE
01. JA
N
.
’00
N
N
CEL
T
I
ME
00 : 00: 00A
M
/
T
I
M
E
STYLE
ATE STYLE
EXT SET BACK CA
A
M
P
M
/
/
/
/
/
D
DD MM YY
CEL
D
ATE STYLE
YY MM DD
/
DD MM YY
N
N
SET SET CA
N
CEL CA CEL
N
or
When you turn the power off (→ P.14), the specified date and time are cleared and
the settings revert to the factory default settings (→ P.34). However, these settings
are not cleared if you switch the camera off (→ P.21).
MEMO
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
Entering Characters
The characters that can be specified are uppercase letters (A to Z), numbers (0 to 9) and some
symbols (<, >, -, /,., : and spaces). Text can be entered anywhere on the screen outside the
character area. Repeat steps w and e in the procedure below for each character entered. If the
text runs over multiple lines, repeat steps q to t for each line. To delete a character, place the
cursor over the l (backspace) and press the s button to delete the text one character at a
time.
Selected position
Character area
q
24 columns
or
w
M
AI
NU
ISPLAY
N
M
E
NU
D
ISPLAY
M
E
NU
or
SET
M
E
D
ATE
D
D
ISPLAY
ISPLAY
ON
ON
T
I
ME
to set the
position
D
MENU
DATE
&
TI
ME
SETTINGS. .
11 lines
CA
M
ER
A
M
E
NU
TXT
D
ISPLAY
ON
Cursor
TXT SETTINGS. .
ABC
D
EFGH I JKL
N
EXT SET BACK CA
NCEL
N
EXT SET BACK CA
NCEL
M
NO
P
QRST X
U
V
W
e
Select a character
and press
t
Text cannot be placed in
the character area
.
r
When you have finished,
move the cursor to [OK].
YZ0123456789
<>
ABC
D
EFGH I JKL
-
/
:
CA
M
E
R
A
1
.
O
K
C
M
NO
P
QRST X
U
V
W
Backspace
Space
Selecting Display/Hide Clock and Text
Select ON to display the date, time and text, and select OFF to hide them. If you select ON, you
can display and hide the date, time and text by pressing theo button.
M
AI
NU
ISPLAY
N
M
E
NU
D
ISPLAY
M
E
NU
D
D
ISPLAY
ISPLAY
M
E
NU
or
SET
M
E
D
ATE
D
D
ISPLAY
ISPLAY
ON
ON
D
ATE
ON
FF
or
or
or
T
I
ME
O
D
M
E
NU
DATE
&
TI
ME
SETTINGS. .
CA
M
E
R
A
M
E
NU
TXT
D
ISPLAY
ON
TXT SETTINGS. .
N
EXT SET BACK CA
NCEL
N
EXT SET BACK CA
N
CEL
SET SET CA
NCEL CANCEL
or
D
ISPLAY
ME
NU
D
D
ISPLAY
ISPLAY
ME
NU
D
ATE
D
D
ISPLAY
ISPLAY
ON
ON
T
I
ME
T
I
ME
ON
FF
DATE
&
TI
ME
SETTINGS. .
O
TXT
D
ISPLAY
ON
TXT SETTINGS. .
N
EXT SET BACK CA
N
CEL
SET SET CA
NCEL CANCEL
or
Example of clock and text display
D
ISPLAY
ME
NU
D
ISPLAY
ME
NU
D
ATE
D
D
ISPLAY
ISPLAY
ON
ON
T
I
ME
DATE
&
TI
ME
SETTINGS. .
TXT
D
ISPLAY
ON
TXT
D
ISPLAY
ON
FF
TXT SETTINGS. .
O
00. 06. 12
N
EXT SET BACK CA
NCEL
SET SET CANCEL CANCEL
CA
M
E
R
A
1
01 : 30 : 00P
M
or
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
Setting the Camera Head Movement Speed and Pan Operation
Use the procedure below to set the speed at which the camera head pans and tilts and to select
the DIRECTION MIRROR setting (direction of camera head panning).
M
AI
NU
ISPLAY
N
M
E
NU
CA
M
E
R
A
M
E
NU
CA
M
E
R
A
M
E
NU
or
or
SET
M
E
PA
N
SPEE
T I LT SPEE
D
D
A
U
T
O
PAN
SPEE
D
A
UTO
A
U
T
O
MANUAL
D
MENU
MO
VABLE
R
A
NGE. .
D
EFAU
LT
CA
M
ER
A
M
E
NU
AE SETTINGS. .
ECTION RROR
D
I
R
M
I
O
FF
N
EXT SET BACK CA
NCEL
N
EXT SET BACK CA
NCEL
SET SET CANCEL CANCEL
CA
M
E
R
A
M
E
NU
CA
M
E
R
A
M
E
NU
PAN
SPEED
A
U
T
O
PAN
SPEED
MA
NUAL
MANUAL
1-2-3-4-5-6-7-8-9-10
SET SET CA
N
CEL CA
NCEL
SET SET CANCEL CANCEL
or
CA
M
E
R
A
M
E
NU
CA
M
E
R
A
M
E
NU
or
PA
N
SPEE
D
A
UTO
T I LT SPEE
D
A
U
T
O
TI LT SPEE
D
A
UTO
M
ANUAL
M
O
VABLE
R
A
NGE. .
D
EFA
U
LT
AE SETTINGS. .
ECTION RROR
D
I
R
M
I
O
FF
N
EXT SET BACK CA
NCEL
SET SET CANCEL CANCEL
CA
M
E
R
A
M
E
NU
CA
M
E
R
A
M
E
NU
TI LT SPEE
D
A
U
T
O
TI LT SPEE
D
MA
NUAL
MANUAL
1-2-3-4-5-6-7-8-9-10
SET SET CA
N
CEL CA
NCEL
SET SET CANCEL CANCEL
or
CA
M
E
R
A
M
E
NU
CA
M
E
R
A
M
E
NU
or
or
PA
N
SPEE
T I LT SPEE
D
D
A
UTO
A
UTO
MO
VABLE
R
A
NGE. .
D
EFAU
LT
AE SETTINGS. .
ECTION RROR
D
I
R
M
I
O
FF
D
I
R
ECTION
M
I
RROR
CEL CA
ON
FF
O
N
EXT SET BACK CA
NCEL
SET SET CA
N
NCEL
● If you set DIRECTION MIRROR to ON, the camera head pans in the direction
indicated on the 4 or 6 button (→ P.16).
NOTE
● The pan and tilt speeds set here are also used in preset position operations
(→ P.20). And also if the “AUTO” setting is selected, the camera head moves at
the maximum speed.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
Setting the Range of Camera Head Movement
Use the procedure below to limit the range of camera pan and tilt (→ P.16). This feature allows
you to watch the image on the monitor as you move the camera head to the position you want to
set as the limit of movement.
or
or
M
AI
NU
ISPLAY
N
M
E
NU
CA
M
E
R
A
M
E
NU
CA
M
E
R
A
M
E
NU
CA
M
E
R
A
M
E
NU
SET
M
E
PA
N
SPEE
T I LT SPEE
D
D
A
UTO
A
UTO
D
MENU
MO
VABLE
R
A
NGE. .
D
EFAU
LT
MO
VABLE
R
A
NGE. .
D
EFA
U
LT
MO
VABLE
R
A
NGE. .
D
EFA
ULT
CA
M
ER
A
M
E
NU
AE SETTINGS. .
ECTION RROR
M
A
NUAL
MANUAL
D
I
R
M
I
O
FF
or
N
EXT SET BACK CA
NCEL
N
EXT SET BACK CA
NCEL
SET SET CA
N
CEL CA
NCEL
SET SET CANCEL CANCEL
M
O
VABLE
LI I T SET 000
LEFT LI
R
A
NG
E
M
O
VABLE
R
A
NG
E
+
+
R
I
GHT
M
D
E
G
R
I
GHT
LI I T SET 000
M
D
E
G
+
+
+
M
I T SET
000
000
000
DE
G
U
P
LI
M
I T SET
D
E
G
DOW
N
LI
M
I T SET
D
E
G
or
or
or
or
N
EXT SET BACK CA
N
CEL
SET SET CA
N
CEL CANCEL
Watch the monitor image to
move to the desired limit.
When you select [YES] the
settings are saved and the
procedure ends.
M
OVABLE
R
A
NG
E
M
OVABLE
R
A
NG
E
+
R
I
GH
LEFT LI
LI
T
LI
M
I T SET 000
D
E
G
+
+
000
When you select [NO] the
procedure ends without
saving the settings.
M
I T SET
LEFT LI
M
I T SET
000
000
000
D
E
G
D
E
G
+
+
U
P
M
I T SET
D
E
G
DOW
N
LI I T SET
M
D
E
G
NEXT SET BACK CA
N
CEL
SET SET CA
N
CEL CANCEL
M
OVABLE
R
A
NG
E
Watch the monitor image to
move to the desired limit.
SAVE SETTINGS?
YES NO
When the setting is
changed
M
O
VABLE
LI I T SET 000
LEFT LI
R
A
NG
E
M
OVABLE
R
A
NG
E
+
R
I
GH
T
M
D
E
G
+
000
+
000
+
000
M
I T SET
D
E
G
+
000
U
P
LI
M
I T SET
D
E
G
U
P
LI
M
I T SET
D
E
G
DOW
N
LI
M
I T SET
D
E
G
NEXT SET BACK CA
N
CEL
SET SET CA
N
CEL CANCEL
Watch the monitor image to
move to the desired limit.
M
O
VABLE
LI I T SET 000
LEFT LI
R
A
NG
E
M
OVABLE
R
A
NG
E
+
R
I
GH
T
M
D
E
G
+
000
+
000
+
000
M
I T SET
D
E
G
U
P
LI
M
I T SET
D
E
G
+
000
DOW
N
LI
M
I T SET
D
E
G
DO
W
N
LI
M
I T SET
D
E
G
NEXT SET BACK CA
N
CEL
SET SET CA
N
CEL CA
NCEL
Watch the monitor image to
move to the desired limit.
The limits for the range of camera head movement are as follows:
VC-C4: ±100° left and right, 90° upward and 30° downward
MEMO
VC-C4R: ±170° left and right, 10° upward and 90° downward
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
Setting the AE
Use the procedure below to specify the AE (brightness adjustment) setting. FLICKERLESS AE
is unnecessary to set.
or
M
AI
NU
ISPLAY
N
M
E
NU
CA
M
E
R
A
M
E
NU
AE SETTING
EFE CE
FLICKE LESS AE
or
SET
M
E
PA
N
SPEE
T I LT SPEE
D
D
A
U
T
O
AE
R
R
EN
D
EFA
U
LT
A
UTO
D
MENU
R
OFF
MO
VABLE
R
A
NGE. .
D
EFAU
LT
CA
M
ER
A
M
E
NU
AE SETTINGS. .
ECTION RROR
D
I
R
M
I
O
FF
N
EXT SET BACK CA
NCEL
N
EXT SET BACK CA
NCEL
NEXT SET BACK CANCEL
[5] corresponds to the Normal
brightness setting (→ P.18)
AE SETTING
EFE CE
LESS AE
AE SETTING
EFE CE
AE SETTING
EFE CE
AE SETTING
AE
R
R
EN
D
EFA
U
LT
AE
R
R
E
N
D
EFA
U
LT
AE
R
R
E
N
D
EFA
U
LT
AE
R
EFE
R
ENCE
M
A
NUAL
M
A
NUAL
MANUAL
FLICKE
R
O
FF
1-2-3-4-5-6-7-8-9-10
SET SET CA CEL CA CEL
N
EXT SET BACK CA
NCEL
SET SET CA
N
CEL CA
NCEL
SET SET CA
N
CEL CA
NCEL
N
N
or
or
VC-C1 Mode and VC-C3 Mode Setting Menu
Use this procedure to set the COMMAND setting for using the VC-C4/VC-C4R in Canon
Communication Camera VC-C1 mode or VC-C3 mode (→ P.28). When you set COMMAND to
VC-C1 mode or VC-C3 mode, some of the setting menus and specifications change, as shown
below.
MAIN MENU
SET MENU
CAMERA MENU
AE SETTING
M
AI
N
M
E
NU
SET
S- 232C ETTINGS. .
TE ON ROLLE
MM
ND VC-C3
ESTOR LT
EXT SET BACK CA
M
E
NU
CA
M
E
R
A
M
E
NU
AE SETTING
SET
M
ENU
R
S
PA
N
SPEE
T I LT SPEE
D
D
A
U
T
O
AE
R
EFE
R
E
N
CE
D
EFA
U
LT
A
UTO
RE
M
O
C
T
R
I
D
0
FLICKERLESS AE
O
FF
CAME
R
A
M
E
NU
C
O
A
MOD
E
AE SETTINGS. .
ECTION RROR
D
I
R
M
I
O
FF
R
E
D
EFAU
N
EXT SET BACK CA
NCEL
N
N
CEL
N
EXT SET BACK CA
NCEL
N
EXT SET BACK CANCEL
● REMOTE CONTROLLER ID in the SET MENU and AE REFERENCE in the AE
SETTING are only enabled in VC-C3 mode and do not appear in the VC-C1
mode.
NOTE
● If you press the s button after changing the mode, the screen momentarily
goes blank. This is not a fault. Also, when you change modes, all the stored
preset positions are cleared and the range of camera head movement reverts
to the default values in each mode.
● The range of pan/tilt/zoom movement in VC-C1 mode corresponds to that
available on the VC-C1 itself.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
RS-232C Settings
These settings are used for controlling the VC-C4/VC-C4R from a PC or other device. The
DATA 8 BIT and NON PARITY settings are fixed, and the menu is used to check them only.
DATA 8 BIT and NON PARITY are to be read only.
M
AI
NU
ISPLAY
N
M
E
NU
SET
S- 232C ETTINGS. .
TE ON ROLLE
MM
ND VC-C4
ESTOR LT
EXT SET BACK CA
M
E
NU
R
S-232C SETTING
S
R
S-232C SETTING
S
or
or
or
SET
M
E
R
S
BAUD
R
ATE
BI T
BIT
I TY
EXT SET BACK CA
9600
BAUD
RATE
4800
9600
14400
19200
D
MENU
RE
M
O
C
T
R
I
D
0
ST
ATA
NON PA
O
P
1
ONLY
ONLY
CAMER
A
M
E
NU
C
O
A
MOD
E
D
8
R
EA
D
R
E
D
EFAU
R
R
EA
D
or
N
EXT SET BACK CA
NCEL
N
N
CEL
N
N
CEL
SET SET CA
NCEL CANCEL
R
S-232C SETTING
BAUD ATE
ST BI T
ATA BIT
NON PA I TY
EXT SET BACK CA
S
R
S-232C SETTING
S
or
or
R
9600
1
OP
ST
OP
BI T
1
2
D
8
R
EA
D
ONLY
ONLY
R
REA
D
N
NCEL
SET SET CA
NCEL CANCEL
● See page 29 for information on the REMOTE CONTROLLER ID setting.
● COMMAND is used when the VC-C4/VC-C4R is used in Canon Communication
Camera VC-C1 or VC-C3 mode (→ P.27).
MEMO
● To restore the default values for the settings (→ P.34), select [SET] in the
RESTORE DEFAULT setting.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
ID Mode
When multiple VC-C4/VC-C4R cameras are connected and installed, all the cameras in range
of the wireless controller simultaneously perform the operations specified. In this situation, the
cameras can be operated individually by assigning separate ID numbers to each camera
beforehand and then specifying the desired ID number from the wireless controller. This is referred
to as ID mode operation.
Setting the ID Number
Use the procedure below to assign an ID number (1-9) to each camera (VC-C4/VC-C4R). If you
do not want to assign an ID number to a camera, select [0] for that camera. Assigning the same
ID number to multiple cameras allows you to control those cameras simultaneously.
1. Switch the power on to the cameras to which you want
to assign the same ID number. Switch the power to the
other connected cameras off.
BRIGHT
ZOOM
Switch the power to a camera off by unplugging the AC adapter
connected to the camera (→ P.14). Even if you turn the power off,
the ID number will not be cleared.
T
W
HOME
2. Press the m button on the wireless controller to display
SET/OK
CANCEL
the MAIN MENU screen.
AF
1
4
7
2
3
6
9
3. Select REMOTE CONTROLLER ID in the SET MENU and
set the ID number.
MF
5
8
∞
Use the 5 and 8 buttons to move the cursor up and down, use
the s button to confirm the selected setting and proceed to the
next level, and use the c button to move back to the previous
level without confirming the selected setting. Use the 5 and 8
buttons to change values.
0
ON SCREEN Fn
ID
MENU
M
AI
NU
ISPLAY
N
M
E
NU
S
E
T
M
E
NU
ETTINGS. .
ON ROLLE
VC-C4
LT
EXT SET BACK CA
or
SET
M
E
R
S- 232C
TE
MM
ND
ESTOR
S
D
M
E
NU
RE
M
O
C
T
R
I
D
0
CA
M
E
R
A
M
E
NU
CO
A
M
OD
E
R
E
D
EFA
U
N
EXT SET BACK CA
NCEL
N
NCEL
S
E
T
M
E
NU
ETTINGS. .
ON ROLLE
VC-C4
LT
EXT SET BACK CA
S
E
T
M
E
NU
or
or
R
S- 232C
TE
MM
ND
ESTOR
S
RE
M
O
C
T
R
I
D
M
0
R
E
M
O
TE
CON
T
ROLLE
R
I
D
5
CO
A
ODE
R
E
D
EFA
U
N
N
CEL
SET SET CA
NCEL CANCEL
4. When you have set the ID number, press the m button
or c button to exit the settings screens.
5. Repeat Steps 1 to 4 until ID numbers are set for all the
cameras.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ID Mode
Selecting the Camera to be Controlled
<Example> As shown in the figure below, of 4 cameras (ID1 to ID3) only the cameras with ID
number 2 (2 cameras) are selected for ID mode operation. In normal operation,
the camera LEDs turn green.
ID2
ID1
ID2
ID3
Green
Green
Green
Green
● Check the LEDs on all the adjacent connected cameras to ensure that all the
cameras are receiving the signals from the wireless controller.
NOTE
● Even if the cameras are switched off, when you press the i button the LEDs
on all the cameras blink orange and you can begin ID mode operation. However,
when a number button was pressed in step 2, the LEDs on cameras with ID
numbers that do not match or that have not been assigned an ID number turn
red and those cameras are switched off.
1. Press the i button.
BRIGHT
ZOOM
T
The LEDs on all the connected cameras blink orange (at 0.5-second
intervals).
W
ID2
ID1
ID2
ID3
HOME
SET/OK
CANCEL
AF
1
4
7
2
3
6
9
Blinking orange Blinking orange Blinking orange Blinking orange
MF
5
8
∞
To cancel ID mode operation, press the c or i button. The
LEDs on all the cameras then turn green.
0
ON SCREEN Fn
ID
MENU
2. Press a number button (in this case 2).
The cameras with ID2 are selected and the LEDs on only those
cameras turn green. The LEDs on the other cameras turn orange
(not blinking).
ID2
ID1
ID2
ID3
Orange
Green
Green
Orange
This completes the selection procedure. When you use the wireless
controller, only the selected cameras will respond. When you press a
button on the wireless controller, the LEDs on the selected cameras
blink green (at 0.1-second intervals) and the LEDs on the other
cameras blink orange (at 0.1-second intervals).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ID Mode
Cancelling ID Mode
<Example> In this example, the selection made in the previous section of the cameras with ID
number 2 is cancelled. The camera LEDs are as shown below.
ID2
ID1
ID2
ID3
Orange
Green
Green
Orange
Check the LEDs on all the adjacent connected cameras to ensure that all the
cameras are receiving the signals from the wireless controller.
NOTE
1. Press the i button.
BRIGHT
ZOOM
T
The LEDs on all the connected cameras blink orange (at 0.5-second
W
intervals).
ID2
ID1
ID2
ID3
HOME
SET/OK
CANCEL
AF
1
4
7
2
3
6
9
Blinking orange Blinking orange Blinking orange Blinking orange
MF
5
8
∞
To cancel ID mode operation, press the c or i button. The
LEDs on all the ID2 cameras turn green and the LEDs on the other
cameras turn orange.
0
ON SCREEN Fn
ID
MENU
2. Press the 0 button.
The LEDs on all the cameras turn green as for normal operation.
ID2
ID1
ID2
ID3
Green
Green
Green
Green
This completes ID mode cancellation. All the cameras will now respond
simultaneously to the signals from the wireless controller.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the following before contacting your Canon supplier.
The wireless controller does not work.
Check 1: The LED is not lit.
Response: Check that the plug is inserted into the main power outlet correctly and
pushed in all the way. → P.14
Check 2: The LED is red.
Response: The camera is switched off. Press the p button on the wireless controller
to switch the camera on. → P.21
Check 3: The LED is orange.
Response: Operation is restricted by the ID mode function. Reset the ID correctly or
cancel ID mode operation. → P.29–31
Check 4: The LED is green.
Response: • Check the remaining charge in the wireless controller batteries.
• Ensure that you are using the wireless controller inside its effective range.
→ P.15
There is no picture on the monitor.
Check 1: The LED is red.
Response: The camera is switched off. Press the p button on the wireless controller
to switch the camera on. → P.21
Check 2: The components are not all connected correctly.
Response: Check that the components are all connected correctly. → P.13
Check 3: Power to the camera or monitor is not switched on.
Response: Turn power on for the camera and monitor. → P.14
Cannot adjust the camera head angle properly.
Check 1: The camera head will not move to the limit of its range of movement.
Response: Something has directly moved the camera head. Press the h button on
the wireless controller. → P.16
Check 2: Restrictions have been applied to the range of camera head
movement.
Response: Change the range of camera head movement. → P.26
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
The camera will not move to a preset position.
Check 1: The camera head will not move to the limit of its range of movement.
Response: Something has directly moved the camera head. Press the h button on
the wireless controller. → P.16
Check 2: The range of pan/tilt movement has been changed since the preset
position was stored.
Response: Store the preset position again. → P.20
The camera will not focus.
Check 1: The camera is set to manual focus mode.
Response: Focus the camera manually or press the a button on the wireless
controller to switch to auto-focus. → P.18–19
Check 2: The lens is dirty.
Response: Clean the lens. → P.8
Check 3: You restored a preset position.
Response: If a preset position is restored when the camera is in manual focus mode,
the camera may be out of focus once it has moved to the preset position.
Adjust the focus manually or press the a button on the wireless controller
to switch to auto-focus. → P.18–19
Check 4: The distance between the subject and the camera is not within the
camera's focal range.
Response: Depending on the zoom position, the camera may not be able to focus at
some distances regardless of whether it is in auto-focus or manual focus
mode. Adjust the distance between the camera and the subject. → P.17
Check 5: You are using auto-focus mode to photograph a subject that is not
suitable for auto-focus mode (→ P.18).
Response: Adjust the focus manually. → P.19
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory Default Settings
When the Product is shipped from the factory or when RESTORE DEFAULT has been set to
[YES] (→ P.28), the settings are set to the default values shown below.
(Camera Default Settings)
Item
Default
Item
Default
Focus
Auto
Preset
None
*
*
Brightness
Normal
Clock and Text
Not displayed
(Setting Screen Default Settings)
Item
Setting
BAUD RATE
STOP BIT
9600
1
DATA 8 BIT
SET MENU
Read only
NON PARITY
Read only
0
REMOTE CONTROLLER ID
COMMAND
VC-C4 MODE
ON
DATE DISPLAY
TIME DISPLAY
ON
TXT DISPLAY
ON
SET DATE
DISPLAY MENU
01.JAN.’00
00:00:00AM
AM/PM
DD/MM/YY
*
*
*
*
SET TIME
TIME STYLE
DATE STYLE
Specified text
None
*
PAN SPEED
TILT SPEED
AUTO (10 for MANUAL)
AUTO (10 for MANUAL)
DEFAULT
MOVABLE RANGE
CAMERA MENU
DIRECTION MIRROR
OFF
AE REFERENCE
FLICKERLESS AE
DEFAULT (5 for MANUAL)
OFF
Settings marked with an asterisk revert to the factory default values when the power is switched
off and then on again (→ P.14). The values for all other settings are saved when the power is
turned off.
*
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Item
Details
Video Signal
Conforms to NTSC color format for USA, Canada
Conforms to PAL color format for Europe, Asia, Oceania
Image Sensor
1/4-inch CCD
Total number of pixels
NTSC: 410,000 (380,000 effective) pixels
PAL: 470,000 (440,000 effective) pixels
Synchronization
Internal
Horizontal Resolution
NTSC: 460 TV lines
PAL: 420 TV lines
Vertical Resolution
S/N Ratio
350 TV lines
48 dB
Scanning Method
Min. subject illumination
Drive Mechanism
2:1 interlaced
6 lux
VC-C4
Pan Mechanism: Rotation angle Left 100°, Right 100°;
Rotation speed: 1°-90° per sec.*
Tilt Mechanism: Tilt angle Up 90° (factory default 30°),
Down 30°; Tilt speed: 1°-70° per sec.
VC-C4R
Pan Mechanism: Rotation angle Left 170°, Right 170°;
Rotation speed: 1°-90° per sec.*
Tilt Mechanism: Tilt angle Up 10°, Down 90°;
Tilt speed: 1°-70° per sec.
Output Terminals
VIDEO OUT: 1 RCA pin jack (output impedance approx. 75 Ω)
S VIDEO OUT: 1 mini-DIN 4-pin socket (output impedance approx. 75 Ω)
RS-232C: 2 mini-DIN 8-pin sockets (input and output)
Up to 9 cameras
Input Terminal
Cascade control
Focusing
Auto/Manual
Aperture
Auto iris servo system
Lens
Focal length 4.0 to 64.0 mm, f/1.4 to f/2.8, 16× power zoom
37 mm (1 15/32 in.), pitch=0.35 mm (1/64 in.)
Lens filter diameter
White Balance
Power Supply terminal
TTL-system full-auto white balance
DC IN. Rated 13 V (Permissible range 11.5 V to 14 V) (EIAJ RC-5320A, 4 voltage sections)
Max. Power Consumption Approx. 12 W; approx. 5 W with camera switched off (including AC power adapter)
Operating Environment
Installation Angle
Dimensions
Temp.: 0°C to 40°C (32°F to 104°F); Humidity: 20-85% RH (no condensation)
±20° from horizontal (±15° with optional wide-angle converter installed)
100 × 112 × 89.5 mm (3 15/16 × 4 7/16 × 3 17/32 in.) (W × D × H) (excluding attachments)
VC-C4: Approx. 375 g (Approx. 0.83 lb.) / VC-C4R: Approx. 435 g (Approx. 0.96 lb.)
WL-V5
Weight
Wireless
Model
Controller
System
Infrared pulse system
Power Supply 3 V DC (2 AA-type batteries)
Dimensions
Weight
50 × 175 × 24.5 mm (1 31/32 × 6 29/32 31/32 in.) (W × D × H) (excluding attachments)
×
Approx. 79 g (Approx. 0.17 lb.) (excluding batteries)
AC Adapter Model
Input
PA-V16
100-240 V AC, 50/60 Hz, 50-65 VA
13 V DC, 1.8 A (max.)
Output
Polarity
External (-), Internal (+)
58 × 118 × 25 mm (2 5/16 × 4 21/32 × 1 in.) (W × D × H) (excluding attachments)
Approx. 205 g (Approx. 0.45 lb.)
Dimensions
Weight
* If you are using a computer to control the camera, the image on the screen may appear shaky
when the camera head is being moved slowly.
● These specifications are subject to change without notice.
● For the AC adapter, use the PA-V16 dedicated unit. Also, do not use the PA-V16 AC adapter
with any other product.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A (serial pin outs and bit rate setting)
RS-232C Pin Out Diagrams
9pin DSUB to 8pin mini-DIN (VC-C4/VC-C4R) Connection
Below is a cable pin out of the cable required to control this equipment from a computer with a
9pin control port.
Personal Computer VC-C4/VC-C4R
9pin DSUB
8pin mini-DIN
1
5
6
7
8
6
9
TxD
RxD
3
2
7
8
6
5
1
4
9
5
3
2
1
3
4
5
1
2
RTS
CTS
DataSet Ready
GND
Female
9pin DSUB
Male
8pin mini-DIN
4,6
Data Carrier Detect
DTR
Personal Computer
VC-C4/VC-C4R
No Connection
7,8
8pin mini-DIN to 8pin mini-DIN (VC-C4/VC-C4R) Connection
Below is a cable pin out of the cable required to control this equipment from a computer with a
8pin control port.
Personal Computer VC-C4/VC-C4R
8pin mini-DIN
8pin mini-DIN
6
7
8
6
7
8
TxD
RxD
3
5
1
5
3
2
3
4
5
3
4
5
1
2
1
2
RTS
CTS
2
1
GND
4
8
6,7
4
6
7,8
Male
8pin mini-DIN
Male
8pin mini-DIN
GND
No Connection
Personal Computer
VC-C4/VC-C4R
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|