Canon Camera Lens 70 200mm F 28L User Manual

EF70-200mm F2.8L IS USM

Instruction

Download from Www.Somanuals.com. All Manuals Search And Download.

a Safety Precautions

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2)

this device must accept any interference received,

including interference that may cause undesired

operation.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Consult the dealer or an experienced radio/TV

technician for help.

Do not make any changes or modifications to the

equipment unless otherwise specified in the

instructions. If such changes or modifications should be

made, you could be required to stop operation of the

equipment.

This equipment has been tested and found to comply

with the limits for a class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications.

This digital apparatus does not exceed the Class B

limits for radio noise emissions from digital apparatus as

set out in the interference-causing equipment standard

entitled “Digital Apparatus”, ICES-003 of the Industry

Canada.

N118

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

ENG-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Nomenclature

Focusing distance range selection switch (→ 5)

Distance scale (→ 10)

Hood mount (→ 12)

Zoom ring (→ 6)

Rubber ring (→ 4)

Filter mounting

thread (→ 12)

Contacts (→ 4)

Focusing ring (→ 6)

Tripod mount (→ 11)

Focus mode switch (→ 5)

Lens mounting index (→ 4)

Image stabilizer switch (→ 7)

Image stabilizer mode selector switch (→ 7)

Orientation locking knob (→ 11)

• Numbers in parentheses indicate reference page numbers.

ENG-3

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Mounting and Detaching the Lens

See your camera’s instructions for details on

mounting and detaching the lens.

The lens mount has a rubber ring for enhanced

water- and dust-resistance. The rubber ring may

cause slight abrasions around the camera's lens

mount, but this will not cause any problems. If the

rubber ring becomes worn, it is replaceable by a

Canon Service Center at cost.

• After detaching the lens, put it down with the

contacts upwards, to avoid damaging the

contacts or lens surface.

• If the contacts are dirty, scratched, or soiled with

fingerprints, etc., corrosion or a faulty

connection or operation may result.

•

Always attach the dust cap to the lens whenever it

is not mounted on the camera. To attach the dust

cap, align the mark on the dust cap with the mark

on the lens and turn the dust cap clockwise. To

remove the dust cap, turn it counterclockwise.

ENG-4

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Setting the Focus

Mode

3. Switching the Focusing

Distance Range

If you are going to take pictures using autofocus, You can set the focusing distance range to

set the focus mode switch to

To focus manually, set the focus mode switch to

and turn the focusing ring.

1.4 m/4.6 ft. to infinity or 2.5 m/8.2 ft. to infinity.

By setting the suitable focusing distance range,

the actual autofocusing time can be shorter.

• Before switching the focusing distance range,

turn the focusing ring so that the current

focusing distance is within the focusing distance

range you want to switch to.

• If the current focusing distance is not within the

focusing distance range you switch to, the lens

focusing may first stop at the start of the

focusing range. This is normal and not a

malfunction. Just press the shutter button

halfway again to resume normal autofocusing.

ENG-5

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Zooming

5. Focusing Ring

To zoom, turn the zoom ring.

The focusing ring can be used at any time

regardless of the focus mode.

• After autofocusing with the camera in ONE SHOT AF

mode, you can adjust the focus by keeping the shutter

button pressed halfway and turning the focusing ring.

• Be sure to finish zooming before focusing.

Zooming after focusing can affect the focus.

• For flash pictures, use an external, EOS-

dedicated Speedlite instead of the camera's

built-in flash. The long lens may partially

obstruct the light of the built-in flash.

ENG-6

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Image Stabilizer Settings

The image stabilizer function can be used in both

and

focus modes.

Set the STABILIZER switch

Select the stabilizer mode.

Press the shutter button

down halfway to check the

stabilization.

• Select MODE 1 for standard

photography. MODE 1 corrects

all vibrations no matter

whether the camera is being

held horizontally, vertically, or

at an angle.

• If you are not going to use the

image stabilizer function, set

• Make sure the image in the

viewfinder is stable, then press

the shutter button all the way

down to take pictures.

the switch to

• To pan a moving subject,

select MODE 2.

MODE 2 corrects vibrations

and shaking only in the

direction at right angles to the

camera’s panning movement.

ENG-7

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Tips on Using the Image Stabilizer

The image stabilizer function is particularly effective for hand-held photography in the following

situations:

● MODE 1

● MODE 2

q In semi-darkened areas such as indoors or

outdoors at night.

w In locations where flash photography is

prohibited, such as art museums and theater

stages.

q When panning subjects in motion.

w When following subjects that are moving

erratically.

* We recommend MODE 1 for all other situations.

e In situations where fast shutter settings

cannot be used.

r In situations where your footing is uncertain.

ENG-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Tips on Using the Image Stabilizer

• When you use a tripod, the Image Stabilizer

should be turned off to save battery power.

• The stabilizer is equally effective for hand-held

photography and photography with a monopod.

• The Image Stabilizer function also operates

when the lens is used with the EF12 II or EF25

II Extension Tube, and the EF1.4X II or EF2X II

Extender.

• If you set the camera’s Custom Function to

change the assigned button to operate the AF,

the Image Stabilizer will operate when you press

the newly assigned AF button.

• The Image Stabilizer cannot compensate for a

blurred shot caused by a subject that moved.

• Set the STABILIZER switch to

when you

are taking pictures using the Bulb setting (long

exposures). If the STABILIZER switch is set to

, the image stabilizer function may introduce

errors.

• The Image Stabilizer might not be fully effective

in the following cases:

• You move the camera for a panned shot.

• You shoot while riding on a bumpy road.

• Compared to using a normal non-IS lens, fewer

shots can be taken when you use an Image

Stabilizer lens because more power is

consumed.

• The image stabilizer operates for about two

seconds even when your finger is off the shutter

button. Do not remove the lens while the

stabilizer is in operation. This will cause a

malfunction.

• With the EOS-1V/HS, 3, 30/33/Elan7/7E,

30V/33V/Elan7N/7NE, Elan ll/Elan ll E/50/50 E,

300/Rebel2000, IX, and D30, the Image

Stabilizer will not work during self-timer

operation.

ENG-9

Download from Www.Somanuals.com. All Manuals Search And Download.

8. Infinity Compensation Mark

9. Infrared Index

To compensate for shifting of the infinity focus

point that results from changes in temperature,

you can rotate the distance scale slightly past

the normal infinity focus mark.

The infrared index corrects the focus setting

when using monochrome infrared film. Focus on

the subject manually, then adjust the distance

setting by moving the focusing ring to the

corresponding infrared index mark.

The compensation amount differs depending on the

focal length. Use the indicated focal length as a

guide when setting the compensation amount.

• The infinity position at normal temperature is the point

•

at which the vertical line of the

with the distance indicator.

mark is aligned

• For accurate manual focusing on subjects at infinity

distance, look through the viewfinder to confirm

focusing while rotating the focusing ring.

Some EOS cameras cannot use infrared film. See

the instructions for your EOS camera.

• The infrared index position is based on a

wavelength of 800 nm.

• Be sure to observe the manufacturer’s

instructions when using infrared film.

• Use a red filter when you take the picture.

ENG-10

Download from Www.Somanuals.com. All Manuals Search And Download.

10. Using the Tripod Mount

Adjusting the Tripod Mount

Loosening the orientation locking knob on the tripod mount allows you to turn the lens and camera freely.

This is useful when you want to switch the camera between horizontal and vertical positions while it is

mounted on a tripod. Once you have set the camera to the desired position, tighten the locking knob firmly.

Detaching the Tripod Mount

First remove the lens from the camera and then remove the tripod mount from the lens as shown

below. To attach the tripod mount, reverse the procedure.

Loosen the orientation

locking knob.

Turn the tripod collar to align

the red dots on the collar

and lens.

Slide off the tripod collar

away from the rear of the

lens.

ENG-11

Download from Www.Somanuals.com. All Manuals Search And Download.

11. Hood

12. Filters

(Optional)

You can attach filters to the filter mounting thread

on the front of the lens.

• If you need a polarizing filter, use Canon’s

PL-C 77 mm ll polarizing filter. Note that you must

remove the hood before adjusting the polarizing filter.

• When the PL-C 77mm ll polarizing filter is attached,

the lens cap cannot be attached.

The ET-86 hood can keep unwanted light out of the lens,

and also protects the front of the lens from rain, snow,

and dust.

To attach the hood, align the hood’s attachment position

mark with the red dot on the front of the lens, then turn

the hood clockwise until the lens’s red dot is aligned with

the hood’s stop position mark.

13. Extension Tubes (Optional)

With Extension Tube EF 12 ll or EF 25 ll, the

camera-to-subject distance and image

magnification will be as follows:

The hood can be reverse-mounted on the lens for storage.

Camera-to-Subject

Magnification

Distance (mm)

• Part of the picture may be blocked if the hood is

not attached properly.

• To attach (remove) the hood, grasp the base of

the hood and turn it clockwise

(counterclockwise). Do not hold the hood by the

outer rim as this could result in the hood being

distorted if too much pressure is applied.

Near

550

Far

624

Near

0.22×

0.24×

0.41×

0.32×

Far

70mm

0.17×

0.06×

0.38×

0.14×

EF12 ll

EF25 ll

200mm 1110

3401

407

70mm

402

929

200mm

1737

ENG-12

Download from Www.Somanuals.com. All Manuals Search And Download.

14. Extenders

(Optional)

With Extender EF 1.4X ll or EF 2X llattached, the lens specifications will change as follows:

Item

With EF1.4X ll Extender

98 – 280

With EF2X ll Extender

140 – 400

Focal length (mm)

Aperture

f/4 – 45

f/5.6 – 64

Diagonal

Vertical

25°20’ – 9°20’

13°50’ – 5°10’

20°50’ – 7°40’

0.24

16°20’ – 6°10’

9°10’ – 3°30’

13°39’ – 5°10’

0.36

Angle of view

Horizontal

Maximum magnification (×)

• Do not attach more than one Extender on the same lens. Having more than one Extender on

the lens will degrade the optical performance and cause exposure errors by the camera's

built-in exposure metering.

• If you use an Extender on the lens mounted on a EOS A2/A2E/5, set the exposure

compensation to -1/2 stop for the EF 1.4X ll or -1 stop for the EF 2X ll.

• AF is possible with Extender.

• When an Extender is attached, the AF speed will become slower by design to retain proper

AF control.

ENG-13

Download from Www.Somanuals.com. All Manuals Search And Download.

15. Specifications

Image Size

24 × 36 mm

Focal Length & Max. Aperture

Lens Construction

Min. Aperture

70 – 200 mm, f/2.8

23 elements in 18 groups

f/32

Angle of View

Diagonal: 34° – 12°

Vertical: 19°30’ – 7°

Horizontal: 29° –10°

Min. Focusing Distance

1.4 m / 4.6 ft.

Max. Magnification & Field of view 0.17 × (at 200 mm), 373 × 559 – 140 × 211mm / 14.6 × 21.8 – 5.5 × 8.2 inch (at 1.4 m)

Filter Diameter

Lens Hood

Max. Diameter & Length

Weight

77 mm

ET-86

86.2 × 197mm / 3.4 × 7.7 inch

1470g / 51.5oz (or 1590g / 55.7oz with the tripod collar)

Lens Cap

E-77U

Case

LZ 1324

• The lens length is measured from the mount surface to the front end of the lens.

• The size and weight listed are for the lens only, except as indicated.

• Aperture settings are specified on the camera.

• All the specifications above are based on Canon’s testing and measuring standards.

• Specifications and appearance are subject to change without notice.

ENG-14

Download from Www.Somanuals.com. All Manuals Search And Download.

2006.9.1

CT1-7533-005

Bosch Appliances Home Security System D1265 User Manual
Bosch Power Tools Power Hammer 11222EVSG User Manual
Braun Mixer MR740cc User Manual
Briggs Stratton Lawn Mower SZC User Manual
Brother All in One Printer MFC J625W User Manual
Cambridge Audio DVD Player 540D V2 User Manual
Canon Camera Accessories HJ15EX85BKRSE V User Manual
Capresso Hot Beverage Maker 260 User Manual
Casio Clock Radio MA0806 B User Manual
Cecilware Coffeemaker Java Giant User Manual