Brocade Enterprise SAN Switch Module
SBCEBFCSW
Brocade Entry SAN Switch Module
SBCEBFCESW
Installation Guide
A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies & Products
Order Number C86450-003
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Safety and regulatory information ......................................................................... v
Electrical Safety ...............................................................................................................vi
Handling electrostatic discharge-sensitive devices .........................................................vii
Electromagnetic compatibility notices (USA) ..............................................................xii
Electromagnetic compatibility notices (International) .................................................xii
Features and specifications ............................................................................................. 2
Installing and replacing a switch module ............................................................ 11
System reliability guidelines ...................................................................................... 12
Removing or replacing a switch module ........................................................................ 17
Information panel ........................................................................................................... 21
LEDs .............................................................................................................................. 22
Establishing a Telnet session in a command-line window .............................................. 30
Establishing a Web-interface session through a Web browser ...................................... 37
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and regulatory information
✏ NOTE
The service procedures are designed to help you isolate problems. They are written with the
assumption that you have model-specific training on all computers, or that you are familiar
with the computers, functions, terminology, and service information provided in this
manual.
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the
instructions. See Intel Server Boards and Server Chassis Safety Information on the
Resource CD and/or at http:\\support.intel.com.
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor
Sie eine der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise
zu Intel-Serverplatinen und -Servergehäusen auf der Ressourcen-CD oder unter
http:\\support.intel.com.
重要安全指导
在执行任何指令之前，请阅读本文档中的所有注意事项及安全声明。参见 Resource
CD（资源光盘） 和/或 http:\\support.intel.com 上的 Intel Server Boards and Server
Chassis Safety Information（《Intel 服务器主板与服务器机箱安全信息》）。
Consignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce
document avant de suivre toute instruction. Consultez Intel Server Boards and Server
Chassis Safety Information sur le CD Resource CD ou bien rendez-vous sur le site
http:\\support.intel.com.
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de
realizar cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis
Safety Information en el CD Resource y/o en http:\\support.intel.com.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
General Safety
Follow these rules to ensure general safety:
•
•
Observe good housekeeping in the area of the machines during and after maintenance.
When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly, or twist,when you attempt to lift.
4. Lift by standing or by pushing up with you leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35lb) or any
object that you think is too heavy for you.
•
•
Do not perform any action that causes hazards to the customer, or makes the equipment unsafe.
Before you start the machine, ensure that other service representatives and the customer’s personnel are
not in a hazardous position.
•
Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
•
•
Keep your tool case away from walk areas so that other people will not trip over it.
Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves
are fastened or rolled up above your elbows. If your hair is long, fasten it.
•
•
Insert the ends of your necktie or scarf inside clothing, or fasten it with a nonconductive clip,
approximately 8 centimeters (3 inches) from the end.
Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
Remember: Metal objects are good electrical conductors.
•
•
•
Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
Reinstall all covers correctly before returning the machine to the customer.
Electrical Safety
xx CAUTION:
Electrical current from power, telephone, and communication cables can be hazardous. To
avoid personal injury or equipment damage, disconnect the server system power cords,
telecommunication systems, networks, and modems before you open the server covers, unless
instructed otherwise in the installation and configuration procedures.
Important: Disconnect all power before performing a mechanical inspection.
Observe the following rules when working on electrical equipment.
•
•
•
Use only approved tools and test equipment. Some hand tools have handles covered with a soft material
that does not protect you when working with live electrical currents.
Many customers have rubber floor mats (near their equipment) that contain small conductive fibers to
decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
Find the emergency power-off (EPO) switch, disconnect switch, or electrical outlet in the room. If an
electrical accident occurs, you can quickly turn off the switch or unplug the power cord.
•
•
Do not work alone under hazardous conditions, or near equipment that has hazardous voltages.
Disconnect all power before:
vi
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
— Performing a mechanical inspection
— Working near power supplies
— Removing or installing main units
•
•
Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box (that supplies power to the machine) and to lock the wall box in the off position.
If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
— Ensure that another person, familiar with the power-off controls, is near you. Remember: another
person must be there to switch off the power, if necessary.
— Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
— Remember: There must be a complete circuit to cause electrical shock. By observing the above rule,
you may prevent a current from passing through your body.
•
•
When using testers, set controls correctly and use the approved probe leads and accessories for that tester.
Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal
floor strips and machine frames.
•
Observe the special safety precautions when you work with very high voltages; these instructions are in
the safety sections of the maintenance information. Use extreme care when measuring high voltages.
•
•
•
•
Regularly inspect and maintain your electrical hand tools for safe operational condition.
Do not use worn or broken tools and testers.
Never assume that power has been disconnected from a circuit. First, check that it has been powered-off.
Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
•
•
Do not touch live electrical circuits with the reflective surface of a plastic dental inspection mirror. The
surface is conductive; such touching can cause personal injury and machine damage.
When the power is on and power supply units, blowers and fans are removed from their normal operating
position in a machine, do not attempt to service the units. This practice ensures correct grounding of the
units.
•
If an electrical accident occurs, use caution:
— Switch power off
— Send another person to get help/medical aid
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (IC) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the server, the part, the work mat, and the person
handling the part are all at the same charge.
✏ NOTE
Use product-specific ESD procedures when they exceed the requirements noted here.
Make sure that the ESD-protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
•
•
•
•
Keep the parts in protective packages until they are inserted into the product.
Avoid contact with other people.
Wear a grounded wrist strap against your skin to eliminate static on your body.
Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices.
Select a grounding system, such as those in the following list, to provide protection that meets the specific
service requirement.
— Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
— Use an ESD common ground or reference point when working on a double-insulated or battery-
operated system. You can use coax or connector-outside shells on these systems.
— Use the round ground-prong of the AC plug on AC-operated computers.
✏ NOTE
The use of a grounding system is desirable but not required to protect against ESD damage.
DANGER
Electrical current from power, telephone and communication cables is hazardous.
To avoid a shock hazard:
•
Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this
product during an electrical storm.
•
•
•
•
•
Connect all power cords to a properly wired and grounded electrical outlet.
Connect to properly wired outlets any equipment that will be attached to this product.
When possible, use one hand only to connect or disconnect signal cables.
Never turn on any equipment when there is evidence of fire, water, or structural damage.
Disconnect the attached power cords, telecommunications systems, networks, and modems before you
open the device covers, unless instructed otherwise in the installation and configuration procedures.
•
Connect and disconnect cables as described in the following table when installing, moving, or opening
covers on this product or attached devices.
To Connect
To Disconnect
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
viii
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
xx CAUTION:
If your system has a module containing a lithium battery, replace it only with the same or an
equivalent type battery recommended by the manufacturer. If your system has a module
containing a lithium battery, replace it only with the same module type made by the same
manufacturer. The battery contains lithium and can explode if not properly used, handled, or
disposed of.
•
•
•
•
•
Do not:
Throw or immerse into water
Heat to more than 100 degrees C (212 degrees F)
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
xx CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or
transmitters) are installed, note the following:
•
•
Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
Use of controls or adjustments or performance of procedures other than those specified herein might
result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments,
and avoid direct exposure to the beam.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
xx CAUTION:
Use safe practices when lifting.
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
xx CAUTION:
The power control button on the device and the power switch on the power supply do not
turn off the electrical current supplied to the device. The device also might have more than
one power cord. To remove all electrical current from the device, ensure that all power cords
are disconnected from the power source.
2
1
xx CAUTION:
Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices.
xx CAUTION:
Do not place any object weighing more then 82 kg (180lbs.) on top of rack-mounted devices.
xx CAUTION:
To avoid personal injury, before lifting the unit, remove all the blades to reduce the weight.
xx CAUTION:
Hazardous energy is present when the blade is connected to the power source. Always
replace the blade cover before installing the blade.
x
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory specifications and disclaimers
Safety compliance
USA:
UL 60950 - 3rd Edition/CSA 22.2. No. 60950
Canada:
cUL certified - 3rd Edition/CSA 22.2. No. 60950- for Canada (product bears the
single cUL mark for U.S. and Canada)
Europe:
Low Voltage Directive, 73/23/EEC
TUV/GS to EN60950 2nd Edition with Amendments, A1 = A2+A3+A4
UL/CB to IEC 60950 3rd Edition
International:
UL/CB - EN60 950 3rd Edition
UL/CB - EMKO-TSE (74-SEC) 207/94
Australia/New Zealand:
CB Report to IEC 60950, 3rd Edition plus international deviations
Electromagnetic compatibility (ECM)
USA:
FCC CFR 47 Part 2 and 15, Verified Class A Limit
Canada:
Europe:
IC ICES-003 Class A Limit
EMC Directive, 89/336/EEC
EN55022, Class A Limit, Radiated & Conducted Emissions
EN55024 ITE Specific Immunity Standard
EN61000-4-2 ESD Immunity (Level 2 Contact Discharge, Level 3 Air Discharge)
EN61000-4-3 Radiated Immunity (Level 2)
EN61000-4-4 Electrical Fast Transient (Level 2)
EN61000-4-5 AC Surge
EN61000-4-6 Conducted RF
EN61000-4-8 Power Frequency Magnetic Fields
EN61000-4-11 Voltage Dips and Interrupts
EN6100-3-3 Voltage Flicker
Japan:
VCCI Class A ITE (CISPR 22, Class A Limit)
IEC 1000-3-2 Limit for Harmonic Current Emissions
Australia/New
Zealand:
AS/NZS 3548, Class A Limit
Taiwan:
BSMI Approval
Korea:
RRL Approval
Russia:
GOST Approval
CISPR 22, Class A Limit
International:
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Electromagnetic compatibility notices (USA)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his/her
own expense.
✏ NOTE
Class A device definition: If a Class A device is installed within the is system, then the system is to be
considered a Class A system. In this configuration, operation of this equipment in a residential area is
likely to cause harmful interference.
✏ NOTE
This product is intended to be installed with CAT5 cable, or equivalent, to minimize electrical
interference.
Electromagnetic compatibility notices (International)
Europe (CE Declaration of Conformity): This product has been tested in accordance too, and complies with
the Low Voltage Directive (73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked with
the CE Mark to illustrate its compliance.
Japan EMC Compatibility:
English translation of the notice above: This is a Class A product based on the standard of the Voluntary
Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in
a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to
take corrective actions.
ICES-003 (Canada): Cet appareil numérique respecte les limites bruits radioélectriques applicables aux
appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: "Appareils
Numériques", NMB-003 édictée par le Ministre Canadian des Communications.
English translation of the notice above: This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the interference-causing equipment standard entitled "Digital
Apparatus," ICES-003 of the Canadian Department of Communications.
xii
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
BSMI (Taiwan): The BSMI Certification number and the following warning is located on the product safety
label which is located visibly on the external chassis.
RRL Korea:
English translation of the notice above:
Device
User’s Information
Class A device
This device complies with RRL EMC and is operated in a commercial environment
so that distributors or users pay attention to this point.
If this product is sold or purchased improperly, please exchange this product to
one that can be used at home.
Class B device
This device complies with RRL EMC and is operated in a residential area so that it
can be used at all other location as well as residential area.
✏ NOTE
Class A device: operated in a commercial area. Class B device: operated in a residential
area.
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Introducing the Brocade Enterprise and Entry
SAN Switch Modules
This Installation Guide contains information about setting up and installing the Brocade*
Enterprise SAN Switch Module SBCEBFCSW and the Brocade Entry SAN Switch Module
SBCEBFCESW into an Intel® Blade Server Chassis. Throughout this document, the term
switch module generically refers to both types of switch modules.
You can install up to two switch modules into an Intel Blade Server Chassis. For installation
information, see the instructions in your Intel Blade Server documentation.
The switch module is a Fibre Channel component that consists of 16 ports:
•
Two external Fibre Channel user ports used to connect to external Fibre Channel
devices
•
14 internal ports to connect to the Intel Blade Server bays
You can manage and configure the switch module through multiple interfaces. For more
You can obtain up-to-date information about the switch module and other Intel server
The Enterprise version comes with a Full SAN Scaling (up to 239 switches) license. This
license allows for up to 239 domain attachments within a fabric. The Entry version is
limited to a two-domain fabric. The Entry version is upgradeable through the purchase of
an optional license key that provides Full SAN Scaling capabilities.
Record information about the switch module in the following table. You will need this
information when you register the switch module with Intel.
Brocade Enterprise SAN Switch Module SBCEBFCSW for Intel®
Blade Server Chassis
Product name
or
Brocade Entry SAN Switch Module SBCEBFCESW for Intel®
Blade Server Chassis
Model number
Serial number
_____________________________________________
_____________________________________________
Media access control (MAC)
address
_____________________________________________
_____________________________________________
Worldwide name (WWN)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
The switch module has five labels:
•
•
•
•
One product name label at the right side of the switch module
One product part number and serial number label at the left side of the switch module
One safety certification label at the left side of the switch module
Two media access control/worldwide name (MAC address/WWN) labels, one on the
information panel on top o fthe switch-module external port 0 and the other on the left
side of the switch module
See Figure 1 on page 9 for the location of the switch-module labels that contain the MAC
address/WWN and serial number information.
Open the shipping carton of the switch module and carefully unpack its contents. The
carton contains the following items:
•
One Fibre Channel switch module: Brocade Enterprise SAN Switch Module
SBCEBFCSW for Intel Blade Server chassis or one Brocade Entry SAN Switch
Module SBCEBFCESW for Intel Blade Server chassis
•
•
•
The Resource CD
One diagnostic wrap plug
Safety information flyer
✏ NOTE
The illustrations in this document might differ slightly from your hardware.
Features and specifications
This section provides a summary of the features and specifications for the switch module.
The switch module has the following features:
•
•
•
•
•
•
•
•
•
•
One PPC405GP processor that operates at 200 MHz
One 256 Kb serial electrically erasable programmable read-only memory (SEEPROM)
One real-time clock with a 10-year battery
Three temperature sensors
Two external autosensing Fibre Channel ports that operate at a maximum of 2 Gbps
14 internal fixed-speed Fibre Channel ports that operate at 2 Gbps
Two internal full-duplex 100 Mbps Ethernet interfaces, terminated at a single MAC
Power-on diagnostics and status reporting
Standard Ethernet and Fibre Channel management information base (MIB) support
External ports that can be configured as F_ports (fabric ports), FL_ports (fabric loop
ports), or E_ports (expansion ports)
•
•
•
Internal ports that are configured as F_ports at 2 Gbps
Frame-filtering technology that enables advanced zoning and monitoring capabilities
Optional short wavelength (SWL) and long wavelength (LWL) small form-factor
pluggables (SFPs)
2
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
The following software features come with the switch module:
•
•
•
•
•
•
Brocade Advanced Web Tools
Brocade Advanced Zoning
Brocade Fabric Watch
Full SAN Scaling (up to 239 switches) (Enterprise version only)
Support for Brocade Fabric Access API and API Scripting Toolkit
Two Domain Fabric (Entry version only)
For information about the standard software features, see the Brocade documentation on the
The following software features are optional:
•
•
•
•
•
•
•
Brocade Advanced Performance Monitoring
Brocade ISL Trunking
Brocade Performance Bundle
Brocade Extended Fabrics
Brocade Advanced Security (Secure OS)
Brocade Remote Switch
Entry Switch Upgrade (Entry version only)
To activate and use these optional software features, you must purchase the corresponding
license keys. For information about these features, see the Brocade Fabric OS Procedures
document. For information about license keys, see Chapter 6, “Advanced features for the
Brocade Enterprise and Entry SAN switch modules,” on page 39.
Table 1 contains the specifications of the switch module.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1. Fibre Channel switch-module specifications .
Fibre Channel switch-module Fibre Channel switch-module Fibre Channel switch-module
standards and protocols:
standards and protocols
(continued):
standards and protocols
(continued):
Fibre Channel standards:
• FC-AL ANSI X3.272:
• FC-AL-2 NCIT S 332:
Fibre Channel protocols:
Fibre Channel protocols
(continued):
• Fibre Channel service
classes: Class 2 and
class 3.
• Buffer credits: 16 buffer
credits per port
• FC-FLA NCIT S
TR-20:
• Operation modes: Fibre
Channel class 2 and class
3, connectionless.
• Media type: Small form-
factor pluggable (SFP)
module
• FC-GS-3 NCITS 348-2000
Rev 7.01
• FC-FG ANSI X3.289:
• FC-FS Rev 1.7
• External port type:
— F_port.
• Fabric port speed: 1.0625
or 2.125 Gbps (gigabits
per second)
• FC-PH ANSI X3.230:
• FC-PH-2 ANSI X3.297:
• FC-PH-3 ANSI X3.303:
• FC-PLDA NCIT S TR-19:
• FC-SW-2 Rev 5.3
— FL_port.
• Maximum frame size: 2148
— E_port.
bytes (2112-byte payload)
— Self-discovery based
on switch type U_port,
an optional port type.
• System processor:
PPC405GP
• Fabric latency: Less than
2.1 µsec from any port to
any port at 2 Gbps, cut-
through routing
• Internal port type: 2 Gbps
is the default setting.
• FC-VI Rev 1.61
• IPFC RFC 2625
• Port characteristics:
External ports are
• SANmark compliance
SCD-3001 v2a1...
• Fabric point-to-point
bandwidth: 2 Gbps or 4
Gbps at full duplex
automatically detected and
self-configuring.
• FC-MI, Rev 1.92
• FC-SB-3 ANSI/INCITS
374:2003
• Number of Fibre Channel
ports: Two external ports
and 14 internal ports.
• Fabric aggregate
bandwidth: 64 Gbps if all
16 ports are running 2
Gbps at full duplex
• FC-BB-2 Rev 5.3
• Scalability: 239 switches
maximum depending on
your configuration.
• Nonblocking architecture
shared-memory switch to
prevent latency
4
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1. Fibre Channel switch-module specifications (continued).
Switch maintainability:
Dimensions:
Switch regulatory
certifications:
• Diagnosis: Power-on self-
test (POST) is performed
on all functional
• Width: 112 mm (4.41 in.)
• Height: 29 mm (1.14 in.)
• Electrical requirements:
— Power source loading:
3.75 amps maximum at
12 V dc
• Depth: 260.3 mm
(10.25 in.)
components except the
SFP module. Port
operational tests include
internal, external, and
online tests.
• Weight: Approximately
.91 kg (2 lb)
— Approximate heat
output in British
thermal units (Btu) per
hour: 85.3 Btu (25
watts)
Environmental:
• User interface: Light-
emitting diode (LED)
indicators.
• Temperature and altitude:
— Operating:
— Operating voltage:
12 V dc
– 10°C to 52° C
(50°F to 125.6°F)
at an altitude of
0 to 914 m
Fabric management:
— Circuit protection:
Internally fused with
over-current protection
• Management methods:
— Web interface through
Advanced Web Tools
(0 to 3 000 ft)
• Safety standards:
– 10°C to 49° C
(50°F to 120.2°F) at
an altitude of
— Command-line
interface (CLI) through
Telnet program
— As a listed accessory
by UL (USA)
0 to 3 000 m
(0 to 10 000 ft)
— As a component by
TUV
— Application program
interface (API)
— Non-operating:
-40° C to 65°C
(-40° F to 149°F) at an
altitude of
— For use only in Intel
Blade Server chassis
• Brocade Fabric Manager
for Intel Blade Server
chassis Advanced Feature
Options:
0 to 12 000 m
(0 to 39 370 ft)
Provides Java*-based
application program to
help manage the storage
area network (SAN) fabric
• Humidity:
— Operating: 8% to 80%,
noncondensing
• Management information
base (MIB)
— Non-operating: 5% to
80%, noncondensing
• Switch simple network
management protocol
(SNMP) agent:
Enables a network
management workstation
to receive configuration
values, traffic information,
and Fibre Channel failure
data through SNMP and
the Ethernet interface
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1. Fibre Channel switch-module specifications (continued).
Switch regulatory
certifications (continued):
Shortwave laser SFP module Longwave laser SFP module
at 1 Gbps and multi-mode
SFP module at 2 Gbps:
at 1 Gbps and 2 Gbps single-
mode:
• Emissions standards:
• Connector: LC-LC Fibre
Channel cable
• Connector: LC-LC Fibre
Channel cable
— FCC part 15B Class A
(USA)
• Color coding: Beige or
black exposed connector
surfaces
• Color coding: Blue
exposed connector
surfaces
— VCCI Class A ITE
(Japan)
— ICES-003 issue 3
(Canada)
• Cable: Fibre Channel 100-
M6-SN-I (50 µm
• Cable: Fibre Channel
100SM-LC-L (9 µm single
mode)
— A4EN55022 level A
(EC)
multimode)
• Wavelength: 830 to 860
nm
• Wavelength:
— Voltage fluctuations:
EN 61000-3-3
1270 through 13.5 nm
• Transmit power: -10 dBm
minimum
• Transmit power: -10 dBm
minimum
— Harmonics: EN 61000-
3-2
• Receiver sensitivity: -16
dBm average
• Receiver sensitivity: -20
dBm average
— Immunity: EN55024:
1998
• Distance:
• Distance: 2 meters
(6.6 ft) to 10 kilometers
(6.21 miles)
— Marking:
– FCC part 15
– UL (United States)
– cUL (Canada)
– TUV
— 500 meters (1640.42 ft)
maximum using 50-
micron fiber
• Safety: DHHS 21 CFR(J),
IEDC 825-1 CENELEC EN
60825-1, VDE
— 300 meters (984.25 ft)
maximum using 62.5-
micron fiber
– VCCI
• Safety: DHHS 21 CFR(J),
IEC 825-1 CENCELEC EN
60825-1, VDE
– CE
Related documentation
This Installation Guide contains setup and installation instructions for the switch module.
This documentation also provides general information about the switch module, including
getting started, how to configure the switch module, and how to access and use online help.
In addition to this Installation Guide, the following related documentation is provided in
Portable Document Format (PDF) on the Resource CD that comes with the switch module:
•
Safety Information: This document contains translated caution and danger
statements. Each caution and danger statement that appears in the
documentation has a number that you can use to locate the corresponding
statement in your language in the Safety Information document.
•
•
Installation and User’s Guide(s) that came with your Intel Server Compute Blade:
These documents contain instructions for setting up and configuring the Blade unit and
basic instructions for installing some options in the Blade unit. It also contains general
information about the Blade unit.
Hardware Maintenance Manual and Troubleshooting Guide that came with your Intel
Blade Server chassis: These documents contain information to help you solve Blade
problems yourself, and they contains information for service technicians.
6
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Rack Installation Instructions: This document contains instructions for installing the
Blade unit in a rack.
Management Module Installation Guide that came with your Intel Blade Server
chassis: This document contains instructions for installing, setting up, starting, and
configuring the management module.
•
•
Management Module User’s Guide that came with your Intel Blade Server chassis:
This document contains instructions for installing, starting, configuring, and using the
management module. It also provides general information about the management
module and contains a description of the management module features.
Management Module Command Line Interface Reference Guide that came with your
Intel Blade Server chassis: This document contains instructions for installing, starting,
configuring, and using the Intel Blade Server management-module command-line
interface. It also provides general information about the management-module
command-line interface and contains a description of its features.
•
•
•
Configuration Options Guide: This document contains information about which small
form-factor pluggable (SFP) module and cable is required to connect the switch
module to other storage devices. This document is at
Fibre Channel Expansion Card Installation and User’s Guide: This document contains
instructions for installing and configuring the Fibre Channel Expansion Card in Intel
Blade Server chassis. It also contains information about updating the basic input/output
system (BIOS) and device drivers of the Fibre Channel Expansion Card.
Brocade Fabric OS Procedures Guide v4.2.0 or later: This document is a valuable
resource for storage area network (SAN) administrators. This document provides a
single location for detailed instructions to perform the most common administrative
fabric and switch procedures.
•
•
Brocade Fabric OS Reference Manual: This document contains detailed information
about the commands that are available with the Brocade command-line interface
through the Telnet program.
Release Notes for Brocade Enterprise SAN Switch Module and Brocade Entry SAN
Switch Module. This document contains updates, changes, issues, and work-arounds
with respect to the switch modules. Read this document for the latest information that
might not be included in the Brocade reference manuals.
•
Brocade Diagnostic and System Error Message Reference Manual: This document
contains diagnostic information, error-message descriptions, and troubleshooting
procedures for the Brocade switch modules.
•
•
Brocade MIB Reference Manual: This document contains information about the
Brocade management information base (MIB).
Brocade Fabric OS Features Guide v4.2.0 or later: This document is a single reference
guide for setup and usage of the many Brocade features, including switch management,
advanced zoning, advanced performance monitoring, Inter-Switch Link (ISL) trunking,
extended fabrics, and remote switch.
•
•
•
Brocade Advanced Web Tools Administrator’s Guide v4.2.0 or later: This document
contains information about the Brocade Advanced Web Tools graphical management
feature. This feature comes with the switch module.
Brocade Fabric Watch User’s Guide v4.2.0 or later: This document contains
information about the Brocade Fabric Watch SAN health monitoring feature. This
feature comes with the switch module.
Brocade ISL Trunking User’s Guide: This document contains information about
requirements for optional ISL trunking on the external ports of the Brocade switch
modules.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Brocade Advanced Performance Monitor User’s Guide: This document contains
information about optional advanced performance-monitoring procedures for the
Brocade switch modules.
Depending on your blade server model, additional documentation might be included on the
Resource CD included with your Intel Blade Server chassis.
Notices and statements used in this document
The following notices and statements are used in this document:
•
•
Notes: These notices provide important tips, guidance, or advice.
Important: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
•
•
•
Attention: These notices indicate potential damage to programs, devices, or data. An
attention notice is placed just before the instruction or situation in which damage could
occur.
Caution: These statements indicate situations that can be potentially hazardous to you.
A caution statement is placed just before the description of a potentially hazardous
procedure step or situation.
Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the description of
a potentially lethal or extremely hazardous procedure step or situation.
Major components of the switch module
Blue on a component indicates a touch point, where you can grip the component to remove
it from or install it in the Blade unit, open or close a latch, and so on.
Green on a component or an green label on or near a component indicates that the
component can be hot-swapped. This means that if the Blade unit and operating system
support hot-swap capability, you can remove or install the component while the Blade unit
is running. Green can also indicate touch points on hot-swap components. See the
Blades documentation on the Resource CD for removing or installing a specific hot-swap
component for any additional procedures that you might have to perform before you can
remove or install the component.
Figure 1 shows the major components of the switch module.
8
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
✏ NOTE
The illustrations in this document might differ slightly from your hardware.
Fibre Channel switch module
Safety certification label
Serial number label
Media access
control (MAC)
address and
world wide name
(WWN) label
!
K
O
0
FC
Information panel
Release-lever latch
Release lever
15
X
!
T
X
R
Figure 1. Fibre Channel switch-module major components.
For more information about the components of the information panel, see Chapter 3,
information about the MAC address, see the Brocade Fabric OS Procedures Guide on the
Resource CD.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Installing and replacing a switch module
Figure 2 shows the I/O bay locations in the Intel® Blade Server Chassis SBCE.
Server chassis
rear view
Switch-module
bay 3
AC
DC
AC
DC
Switch-module
bay 4
TP00710
Figure 2. SBCE unit (rear view) with I/O bay identification.
You must install Fibre Channel switch modules only in I/O bays 3 and 4 of the SBCE unit.
The Fibre Channel Expansion Card has two 2 Gbps Fibre Channel ports. At least one
switch module is required when you install the Fibre Channel Expansion Card in the Blade
server. Installing a switch module in I/O bay 3 or bay 4 provides the first connection to any
installed Fibre Channel Expansion Cards in the Blade unit. Installing a second switch
module enables a second connection to a Fibre Channel Expansion Card in the Blade unit.
Adding a second switch module provides a redundant path and a separate Fibre Channel
connection from the SBCE unit to the external Fibre Channel network and SAN.
Important: The switch modules in I/O bays 3 and 4 and all blade server expansion cards in
the Blade unit must use the same interface type. Therefore, you must install Fibre Channel
expansion cards when you install Fibre Channel switch modules into the Blade unit.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table summarizes the application for each switch module.
Bay
Fibre Channel switch-module function
3
4
Port 0 connection on the Intel Blade Server Fibre Channel Expansion Card in the Blade
unit
Port 1 connection on the Intel Blade Server Fibre Channel Expansion Card in the Blade
unit
The second switch module port connection allows for dual paths from the blade server to
external Fibre Channel devices.
Installation guidelines
Before you begin to install the switch module in the SBCE unit, read the following
information:
•
Become familiar with the safety and handling guidelines specified under “Safety and
and read the safety statements in Blade unit option documentation.
•
•
Blue on a component indicates touch points, where you can grip the component to
remove it from or install it in the Blade unit, open or close a latch, and so on.
Green on a component or an green label on or near a component indicates that the
component can be hot-swapped, which means that if the Blade unit and operating
system support hot-swap capability, you can remove or install the component while the
Blade unit is running. Green can also indicate touch points on hot-swap components.
See the instructions in this chapter and the Installation and User’s Guide(s) on the
Resource CD for removing or installing a specific hot-swap component and for any
additional procedures that you might have to perform before you remove or install the
component.
•
•
You do not have to turn off the Blade unit to install or replace any of the hot-swap
modules on the rear of the Blade unit.
For a list of supported options for your SBCE unit, go to
System reliability guidelines
Attention: To help ensure proper cooling and system reliability, make sure that:
•
•
•
Each of the I/O bays on the rear of the SBCE unit has either a module or filler module
installed.
A removed hot-swap module is replaced with an identical module or filler module
within 1 minute of removal.
A removed hot-swap blade server is replaced with an identical blade server or a filler
blade within 1 minute of removal.
•
•
The ventilation areas on the sides of the switch module are not blocked.
You have followed the reliability guidelines in the documentation that comes with the
SBCE unit.
12
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling static-sensitive devices
Attention: Static electricity can damage electronic devices. To avoid damage, keep static-
sensitive devices in their static-protective packages until you are ready to install them.
To reduce the possibility of electrostatic discharge, observe the following precautions:
•
•
•
•
•
Limit your movement. Movement can cause static electricity to build up around you.
Handle the device carefully, holding it by its edges or its frame.
Do not touch solder joints, pins, or exposed printed circuitry.
Do not leave the device where others can handle and damage it.
While the device is still in its static-protective package, touch it to an unpainted metal
part of the SBCE unit for at least 2 seconds. This drains static electricity from the
package and from your body.
•
Remove the device from its package and install it directly into the SBCE unit without
setting down the device. If it is necessary to set down the device, put it back in
its static-protective package. Do not place the device on the SBCE unit or on a
metal surface.
•
•
Take additional care when handling devices during cold weather. Heating reduces
indoor humidity and increases static electricity.
Wear an electrostatic wrist strap, if one is available.
Installing a switch module
Statement 3:
xx CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
•
Do not remove the covers. Removing the covers of the laser product could result in
exposure to hazardous laser radiation. There are no serviceable parts inside the
device.
•
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
Danger:
Danger: Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the
following.
Laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
`
Appareil A Laser de Classe 1
Statement 8:
xx CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
xx CAUTION:
Hazardous voltage, current, and energy levels are present inside any component that
has this label attached. There are no serviceable parts inside these components. If you
suspect a problem with one of these parts, contact a service technician.
Complete the following steps to install a switch module:
2. Remove the acoustic attenuation module option, if necessary, from the rear of
the Blade unit. See the Installation and User’s Guide for your Blade unit on the
Resource CD for detailed removal instructions.
Acoustic
attenuation
module
Locking
handle
Figure 3. Removing the acoustic attenuation module.
3. Make sure that the Blade unit is turned on, the green dc power LED on each power
module is lit, and the green OK LED on the management module is lit.
4. Select only I/O bay 3 or bay 4 in which to install the switch module.
5. Remove the filler module from the I/O bay in which you are installing the switch
module. Store the filler module for future use.
14
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6. If you have not already done so, touch the static-protective package that contains the
switch module to an unpainted metal part of the Blade unit for at least 2 seconds.
7. Remove the switch module from its static-protective package.
8. Squeeze the release-lever latch to move the insertion arm, as shown in the following
illustration.
Release-lever
latch
OK
!
2
TX
RX
G
!
0
FC
15
!
2
G
TX
RX
Figure 4. Squeezing the release-lever latch.
9. Pull the release lever down to completely open the lever, as shown in the following
illustration. When the lever is in the open position, you can correctly install the switch
module in the Blade unit.
O
K
!
2G TX
RX
!
0
FC
15
2G
T
X
RX
!
Figure 5. Opening the release lever.
10. With the port side facing you and the release lever in the open position (perpendicular
to the module), slide the switch module into the I/O bay until it stops.
Figure 6 on page 16 shows how to install a switch module in the rear of the SBCE unit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch module
SBCE unit
A
O
C
K
!
D
C
O
K
!
2
T
X/
/
R
X
L
I
N
3K
T
X
/
R
X
L
I
N
2
T
R
4K
G
X
T
0
X
0
/
X
0
R
!
5
5
D8
8
9
A
1
0
FC
C
O
K
!
1
5
2
G
T
R
X
X
!
A
O
C
K
!
D
C
0
2
FC
C
T
X
/
R
X
L
I
N
1
5
3K
2
G
T
T
R
X
X
X
/
R
Release lever
X
L
I
N
!
4K
T
A
0
X
0
/
0
R
5
5
D8
8
9
Release-lever latch
Figure 6. Installing a switch module.
11. Raise the release lever until it moves to the upright (closed) position. This locks the
switch module in the SBCE unit.
✏ NOTE
The switch module takes approximately 60 seconds to complete the power-on
self-test (POST). When the switch module is turned on, an LED test occurs. All
LEDs are lit and remain lit for approximately 5 seconds; then, the LEDs will all
turn off, except the OK LED. The OK LED flashes to indicate a normal POST
condition; then, POST proceeds as described in the next step.
✏ NOTE
To maintain proper airflow, make sure that the ventilation areas on the sides of
the switch module are not blocked.
12. Make sure that the LEDs on the switch module indicate that it is operating correctly.
Make sure that:
•
When the POST starts, the green OK LED on the switch module is flashing. The
POST tests the condition of firmware, memory, data paths, and switch logic and
uses the fault LED to indicate pass or fail conditions.
•
The green OK LED on the switch module stops flashing to indicate that the switch
logic has completed POST.
14. If you are using the external switch-module ports, connect an SFP module
option to external Fibre Channel port 0 and Fibre Channel port 15. For SFP
16
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
module installation instructions, see the documentation that comes with the
SFP module.
✏ NOTE
SFP module options do not come with the switch module, but are required if you
want to use external switch-module ports.
15. Use LC-LC or LC-SC fiber-optic cables to connect the switch-module external
ports to external Fibre Channel devices. For more information, see the
documentation that comes with the cable options.
✏ NOTE
You can remove and replace an SFP module while the switch module is
operating without damaging the switch module or the SFP module. However,
transmission on the affected port will be interrupted until the SFP module and
cables are installed. See the documentation that comes with the connected Fibre
Channel device for information about installation, configuration, and startup
sequence.
Removing or replacing a switch module
Statement 8:
xx CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
xx CAUTION:
Hazardous voltage, current, and energy levels are present inside any component that
hed. There are no serviceable parts inside these components. If you
with one of these parts, contact a service technician.
Complete the following steps to replace a switch module:
2. Remove the acoustic attenuation module, if any, from the rear of the SBCE unit. For
Chassis SBCE Installation and User’s Guide on the Resource CD that came with
your SBCE unit.
3. Remove the LC-LC or LC-SC fiber-optic cables from the two external ports on the SFP
module. Removing these cables disrupts the network connection from the external
Fibre Channel port to any connected external Fibre Channel devices. For removal
instructions, see the documentation that comes with the cable options.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove any SFP modules from the switch-module external Fibre Channel ports. For
SFP module removal instructions, see the documentation that comes with the SFP
module.
The module moves out of the bay approximately 0.6 cm (0.25 inch).
Switch module
SBCE unit
A
O
C
K
!
D
C
O
K
!
2
T
X/
/
R
X
L
I
N
3K
T
X
/
R
X
L
I
N
2
T
R
4K
G
X
T
0
X
0
/R
X
0
!
5
5
D8
8
9
A
0
FC
C
O
K
!
1
5
2
G
T
R
X
X
!
A
O
C
K
!
D
C
0
2
FC
C
T
X
/
R
X
L
I
N
1
5
3K
2
G
T
T
R
X
X
X
/
R
Release lever
X
L
I
N
!
4K
T
A
0
X
0
/
0
R
5
5
D8
8
9
Release-lever latch
Figure 7. Removing a switch module.
✏ NOTE
If you do not replace the switch module, you must insert a filler module into the
empty bay within 1 minute.
6. Slide the switch module out of the bay and set it aside. Within 1 minute, place either
another switch module or a filler module in the bay.
✏ NOTE
To make sure that the switch module is active after you replace it, see step 11 on
7. If you placed another switch module into the bay and if you are using the external
switch-module ports, insert any SFP modules that you removed in step 4 on page 14
into external Fibre Channel port 0 and Fibre Channel port 15. For SFP module
installation instructions, see the documentation that comes with the SFP
module.
18
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Use LC-LC or LC-SC fiber-optic cables to connect the switch-module external ports to
external Fibre Channel devices. For more information, see the documentation that
comes with the cable options.
For detailed installation instructions, see the Intel Server Chassis SBCE
Installation and User’s Guide on the Resource CD.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Information panel LEDs and external Fibre
Channel ports
This chapter describes the information panel and LEDs on the switch module and the
external Fibre Channel ports on the information panel.
Information panel
The switch-module information panel contains LEDs and two Fibre Channel ports, as
shown in Figure 8.
OK
!
System status LEDs
TX
2G
!
RX
Port 0 LEDs
0
Port 0
FC
Port 15
15
Port 15 LEDs
TX
2G
RX
!
Figure 8. Fibre Channel switch-module information panel.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
The switch-module information panel contains the following components:
•
Comprehensive LEDs that display the status of the switch module and the network. For
more information, see “LEDs.”
•
Two external Fibre Channel connectors to connect Fibre Channel devices, such as disk
subsystems, tape drives, and other servers; and SAN devices, such as Fibre Channel
switches, extenders, and gateways. These connectors are identified as port 0 and port
15 in the switch configuration menus and are labeled 0 and 15 (from top to bottom) on
✏ NOTE
The internal connectors are numbered 1 through 14.
LEDs
After you install the switch module in the SBCE unit, the switch-module LEDs become
active. There are three possible LED states: off, lit, and flashing. The lit (steady) LEDs and
flashing LEDs can be green or amber.
The LEDs might display any of these states and colors during startup, POST, or other
diagnostic tests. This is typical and does not indicate a problem, unless the LEDs do not
indicate a healthy state after all the startup (boot) processes and diagnostic tests have been
completed. If one or more LEDs do not display a healthy state, make sure that the LEDs are
not set to beacon. For information about how to turn beaconing on and off, see the Brocade
Fabric OS Procedures Guide or the Brocade Advanced Web Tools Administrator’s Guide
v4.2.0 or later on the Resource CD.
Any errors that are detected during POST are written to the system log. This log is
accessible through the errShow command. For information about this command, see the
Brocade Fabric OS Procedures Guide on the Resource CD. For information about error
messages, see the Brocade Diagnostic and System Error Message Reference Manual on the
Resource CD.
✏ NOTE
You can also use the management module to make sure that the switch module is
correctly operating. For more information, see the Intel Server Chassis SBCE
Installation and User’s Guide and the Intel Server Chassis SBCE Hardware
Maintenance Manual and Troubleshooting Guide on the Resource CD.
Figure 9 shows the locations of the LEDs on the switch module. To interpret the meaning of
the LED states, see Table 2.
22
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
OK
!
OK LED (green)
Port speed LED
Fault (system error)
LED (amber)
Port diagnostics LED
TX
RX
2G
!
0
Port status LED
Figure 9. Fibre Channel switch-module LEDs. Notes:
•
•
The illustrations in this document might differ slightly from your hardware.
An amber LED is lit when a system error or event has occurred. To identify the error or
event, check the LEDs on the information panel of the switch module and see Table 2
for more information.
•
•
An LED test occurs whenever the switch module is turned on. All LEDs are lit and
remain lit for approximately 5 seconds; then, the LEDs will all turn off, except the OK
LED. The OK LED flashes to indicate a normal POST condition; then, POST proceeds
as described in step 12 on page 16.
See the diagnostic section of the Brocade Diagnostic and System Error Message
Reference Manual on the Resource CD for more information about the LEDs.
Table 2. Switch-module LED descriptions .
LED name
LED color and state
None
Hardware status
System status (OK
and !)
The switch module is off or receiving no power.
System status (OK) Green: Steady
The switch module is on and the power modules in
the SBCE unit are correctly operating.
Green: Flashing
Green: Off
POST is running.
The amber LED is lit or there is no power.
Fault. POST failure or critical alert.
System status (!)
(Fibre Channel
switch-module fault)
Amber: Steady
When this LED is lit, the system-error LED on the
SBCE unit is also lit.
Amber: Off
The green LED is lit, indicating a healthy switch, or, if
the green LED is off, there is no power.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. Switch-module LED descriptions (continued).
LED name
Port speed
LED color and state
Hardware status
Green: Off
The indicated Fibre Channel switch-module port (0 or
15) is operating at 1 Gbps.
Green: On
Green: Off
The indicated Fibre Channel switch-module port (0 or
15) is operating at 2 Gbps.
Port status
No signal or the port diagnostics LED is active on the
indicated port (0 or 15).
Green: Steady
The indicated port (0 or 15) is online.
Green: Flickering
The indicated port (0 or 15) is connected and Fibre
Channel activity is occurring on that port.
Green: Flashing slowly The indicated port (0 or 15) is online but segmented
from the connected switch or device.
Green: Flashing rapidly The indicated port (0 or 15) is in the internal loopback
mode because of diagnostics.
Port diagnostics
Amber: Off
No faults on the indicated port (0 or 15).
Amber: Steady
The indicated port (0 or 15) signal is present but not
online.
Amber: Flashing slowly The indicated port (0 or 15) has been disabled, or
switch beaconing is on.
Amber: Flashing rapidly This LED is lit on the indicated port (0 or 15) when the
port-diagnostics program has discovered an error
(port fault).
✏ NOTE
24
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Configuring the switch module through the
Telnet interface
The switch module contains a Telnet server. This server enables a Telnet client to establish
a Telnet session with the Fibre Channel switch module to retrieve information or to
configure parameters using the command-line interface (CLI). You can perform a variety of
fabric and switch-management tasks through an Ethernet connection using the CLI.
You can access the Telnet interface in two ways:
•
•
In the SBCE management-module Web interface
In a command-line window on a network management workstation
For you to configure the switch module through the Telnet interface, the Internet protocol
(IP) address and subnet masks must be compatible, and the following configuration settings
in the management module must be enabled:
•
•
Switch-module external port 0 and port 15
External management for external port 0 and port 15
For you to access a switch module from a network management workstation, make sure that
it is connected to an external SBCE management-module Ethernet port.
To enable the configuration settings in the management-module Web interface, click I/O
Module Tasks → Management → Advanced Switch Management → Advanced Setup.
Important: Before you configure the switch module, make sure that the management
modules in the SBCE unit are correctly configured. In addition, for you to access and
manage the switch module from an external environment, you might have to enable certain
features, such as the external ports and external management over all ports. See the
applicable Intel Server Chassis SBCE Installation and User’s Guide documents on the
Resource CD for more information. For information about configuring the switch module,
see the Brocade Fabric OS Reference Manual on the Resource CD.
Connecting to the switch module
To use the Telnet program (in VT100 compatible terminal mode) to access and control the
switch module, you must know the IP address for the switch module and have an existing
network connection. If you have to obtain the IP address for the switch module or establish
a network connection, contact your system or network administrator.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Establishing a Telnet session through the management
module
Complete the following steps to establish a Telnet session through the Blade management
module:
1. In your browser, in the address bar, type http://xxx.xxx.xxx.xxx, where xxx.xxx.xxx.xxx is
the IP address of the SBCE management-module interface. Click GO or press Enter.
The Enter Network Password window opens.
✏ NOTE
The default IP address for the SBCE management module is 192.168.70.125.
Figure 10. Enter Network Password window.
2. In the User Name field, type the initial default user name, USERID. In the Password
field, type the initial default password, PASSW0RD(the sixth character is a zero, not
the letter O). The user name and password are case sensitive.
The Active Session from Same Client window opens.
Figure 11. Active Session from Same Client window. 3.In the Inactive session
timeout value field, select the timeout value for this Web session and click Start New
Session. The SBCE management-module main window opens.
26
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 12. Management-module main window.
4. In the left navigation pane, under I/O Module Tasks, click Management. The I/O
Module Management window opens.
Figure 13. Switch Management window.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
page 28 opens.
Figure 14. Switch Management window showing switch-module 3 example.
6. Make sure that the IP address is the same in the Current IP Configuration and New
Static IP Configuration sections.
7. Scroll down and click Advanced Switch Management. A window similar to the one
in Figure 15 opens.
Figure 15. Switch Management window - advanced.
28
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. To start a Telnet session, scroll down to the Start Telnet/Web Session section and
click Start Telnet Session.
The management-module command-prompt window opens, as shown in Figure 16.
Figure 16. Management-module command-prompt window for Fibre Channel
switch module.
9. At the Loginprompt, type the initial default user name, USERID, and press Enter. At
the Passwordprompt, type the initial default password, PASSW0RD(the sixth
character is a zero, not the letter O), and press Enter. The user name and password are
case sensitive.
10. If you are accessing the switch module for the first time, press Enter to change the
switch passwords. You are prompted for a password for the root, factory, and user
accounts.
Figure 17. Management-module password-change window.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
After you have changed all of the passwords, the command prompt is displayed in a
window similar to the one in Figure 18 on page 30.
Figure 18. Management-module command-line interface window.
11. To open online help to view the available commands, type helpand press Enter.
For more information about using the CLI, see the Brocade Fabric OS Reference Manual
on the Resource CD.
Establishing a Telnet session in a command-line window
You can access the switch module by IP-enabled devices that are connected to the SBCE
management module. An Ethernet connection to the management-module external ports on
the Blade unit is required. For more information, see the following documents on the
Resource CD:
•
•
•
Intel Server Chassis SBCE Installation and User’s Guide
Intel Server Chassis SBCE Management Module Installation Guide
Intel Server Management Module SBCECMM Installation and User’s Guide
Complete the following steps to establish a Telnet session through a command-line
window:
1. Open a command-line window on the network-management workstation.
2. Type one of the following commands and press Enter. The IP addresses in these
commands are default IP addresses.
For the switch module in I/O bay 3:
telnet 192.168.70.129
For the switch module in I/O bay 4:
telnet 192.168.70.130
30
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
A Telnet command-prompt window opens.
Figure 19. Telnet command-prompt window.
3. At the Loginprompt, type the initial default user name, USERID, and press
Enter. At the Passwordprompt, type the initial default password,
PASSW0RD(the sixth character is a zero, not the letter O). The user name and
password are case sensitive.
4. If you are accessing the switch module for the first time, press Enter to change the
switch passwords. You are prompted for a password for the root, factory, and user
accounts.
Figure 20. Telnet password-change window.
After you have changed all of the passwords, the command prompt is displayed in a
window similar to the one in Figure 21.
Figure 21. Telnet command-line interface window.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Configuring the switch module through the
Advanced Web Tools interface
The switch module contains a Web server interface known as Advanced Web Tools. This
server enables a Web-based client to establish a Web-interface session with the Fibre
Channel switch module to retrieve information or to configure parameters using a Web
browser. You can perform a variety of fabric and switch-management tasks through an
Ethernet connection using a Web browser.
You can access the management-module Web interface in two ways:
•
•
In the SBCE unit management-module Web interface
Through a Web browser on a network-management workstation
Advanced Web Tools is a graphical interface that requires a Web browser to view and
manage the switch. For information about system requirements and supported Web
browsers, see the Brocade Advanced Web Tools Administrator’s Guide v4.2.0 or later on the
Resource CD.
For you to configure the switch module through the Web interface, the IP address and
subnet masks must be compatible, and the following configuration settings in the
management module must be enabled:
•
•
Switch-module external port 0 and port 15
External management for external port 0 and port 15
For you to access a switch module from a network management workstation, make sure that
it is connected to an external SBCE management-module Ethernet port.
To enable the configuration settings in the management-module Web interface, click I/O
Module Tasks → Management → Advanced Switch Management → Advanced Setup.
Important: Before you configure the switch module, make sure that the management
modules in the SBCE unit are correctly configured. In addition, for you to access and
manage the switch module from an external environment, you might have to enable certain
features, such as the external ports and external management over all ports. See the Intel
Server Chassis SBCE Installation and User’s Guide documents on the Resource CD for
more information. For information about configuring the switch module, see the Brocade
Advanced Web Tools Administrator’s Guide v4.2.0 or later on the Resource CD.
Connecting to the switch module
For you to use the Advanced Web Tools interface to access and control the switch module,
you must know the IP address for the switch module and have an existing network
connection. If you have to obtain the IP address for the switch module or establish a
network connection, contact your system or network administrator.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Establishing a Web-interface session through the
management module
Complete the following steps to establish a Web-interface session through the Blade
management module:
1. In your browser, in the address field, type http://xxx.xxx.xxx.xxx, where xxx.xxx.xxx.xxx
is the IP address of the Blade management-module interface. Click GO or press Enter.
The Enter Network Password window opens.
✏ NOTE
The default IP address for the Blade management module is 192.168.70.125.
Figure 22. Enter Network Password window.
2. In the User Name field, type the initial default user name, USERID. In the Password
field, type the initial default password, PASSW0RD(the sixth character is a zero, not
the letter O). The user name and password are case sensitive.
The Active Session from Same Client window opens.
Figure 23. Active Session from Same Client window.
3. In the Inactive session timeout value field, select the timeout value for this Web
session and click Start New Session. The Blade management-module main window
opens.
34
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 24. Management-module main window.
4. In the left navigation pane, under I/O Module Tasks, click Management. The Switch
Management window opens.
Figure 25. Switch Management window.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click the link for either switch module 3 or switch module 4. A window similar to the
Figure 26. Switch Management window showing switch module 3 example.
6. Make sure that the IP address is the same in the Current IP Configuration and New
Static IP Configuration sections.
7. Scroll down and click Advanced Switch Management. A window similar to the one
in Figure 27 opens.
Figure 27. Switch Management window - advanced.
36
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. To start a Web-interface session, scroll down to the Start Telnet/Web Session section
and click Start Web Session.
The switch-module Advanced Web Tools interface window opens, as shown in Figure
Figure 28. Advanced Web Tools interface window (management-module view).
9. To perform switch-module administrative tasks, click Admin, and log in to the switch.
In the User Name field, type the initial default user name, USERID. In the Password
field, type the initial default password, PASSW0RD(the sixth character is a zero, not
the letter O). The user name and password are case sensitive.
For more information about using the Advanced Web Tools interface, see the Brocade
Advanced Web Tools Administrator’s Guide v4.2.0 or later on the Resource CD.
Establishing a Web-interface session through a Web
browser
You can access the switch module by IP-enabled devices that are connected to the SBCE
management module. An Ethernet connection to the management-module external ports on
the Blade unit is required. For more information, see the following documents on the
Resource CD:
•
•
•
Intel Server Chassis SBCE Installation and User’s Guide
Intel Server Chassis SBCE Management Module Installation Guide
Intel Server Management Module SBCECMM Installation and User’s Guide
Complete the following steps to establish a Web-interface session through a Web browser:
1. Open a supported Web browser on the network-management workstation.
2. Type one of the following Web addresses in the address field and press Enter. These
Web addresses contain default IP addresses.
For I/O bay 3:
37
Download from Www.Somanuals.com. All Manuals Search And Download.
For I/O bay 4:
The switch-module Advanced Web Tools interface window opens, as shown in Figure
Figure 29. Advanced Web Tools interface window (Web-browser view).
3. To perform switch-module administrative tasks, click Admin, and log in to the
switch. In the User Name field, type the initial default user name, USERID. In
the Password field, type the initial default password, PASSW0RD(the sixth
character is a zero, not the letter O). The user name and password are case sensitive.
For more information about using the Advanced Web Tools interface, see the Brocade
Advanced Web Tools Administrator’s Guide v4.2.0 or later on the Resource CD.
38
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Advanced features for the Brocade Enterprise
and Entry SAN switch modules
You can upgrade the switch module to use the following optional features after you
Enterprise version and the Entry version of the switch module.
Table 3. Optional features
Optional feature
Description
Brocade Advanced Performance Monitoring
• Provides advanced performance-monitoring
procedures through the Brocade switch
module:
— End-to-end operations
— Small computer system interface (SCSI)
read operations
— SCSI write operations
— SCSI read/write operations
— SCSI versus IP traffic-usage comparisons
• Enables performance tuning of the Brocade
SAN
Brocade ISL Trunking
• Logically combines the two external switch-
module ports (0 and 15) into one 4 Gb trunk
link when the ports are connected (inter-switch
linked) to another Brocade switch module
• Ensures optimum performance for servers that
use this trunk
Brocade Performance Bundle
Brocade Extended Fabrics
Includes both the Advanced Performance
Monitoring and ISL Trunking advanced features
Enables full bandwidth performance at extended
distances up to 100 km (62.14 miles).
For more information about configuring the
Extended Fabrics feature, see the Release Notes
for Brocade Enterprise SAN Switch Module and
Brocade Entry SAN Switch Module on the
Resource CD.
Brocade Advanced Security (Secure OS)
Provides increased security for the Brocade SAN
through encryption, digital certificates, digital
signatures, and various access-control lists
Brocade Remote Switch
Connects two Brocade fabrics over a wide area
network (WAN)
Brocade Entry Switch Upgrade
Increases the scalability of the Entry version from
two switches in the fabric to Full SAN Scaling (up to
239 switches).
This feature is available only for the Entry version.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
To activate and use these optional software features, you must purchase the corresponding
license keys. For information about these features, see the following documentation on the
Resource CD:
•
•
•
Brocade Fabric OS Procedures Guide v4.2.0 or later
Brocade Fabric OS Reference Manual
Release Notes for Brocade Enterprise SAN Switch Module and Brocade Entry SAN
Switch Module
•
•
•
•
•
Brocade Diagnostic and System Error Message Reference Manual
Brocade Fabric OS Features Guide v4.2.0 or later
Brocade Advanced Web Tools Administrator’s Guide v4.2.0 or later
Brocade ISL Trunking User’s Guide
Brocade Advanced Performance Monitor User’s Guide
See “Related documentation” on page 6 for descriptions of these documents.
The Enterprise version comes with a Full SAN Scaling (up to 239 switches) license. This
license allows for up to 239 domain attachments within a fabric. The Entry version is
limited to a two-domain fabric. The Entry version is upgradeable through the purchase of
an optional license key that provides Full SAN Scaling capabilities.
Before you can upgrade and install a new license key, you must determine the license
identifier (ID) of the switch module. Use the Telnet program to log in to the switch module
ID value future reference. For information about this command, see the Brocade Fabric OS
Reference Manual on the Resource CD.
To purchase and obtain a license key for an optional feature, go to contact your your Intel
support representative. A license key will be provided through the Web site that is described
in the documentation that you receive after you purchase the feature.
To install an optional feature on the switch, you must add the corresponding license to the
list of current features for the switch. Use the Telnet program to log in to the switch module
feature. For information about this command, see the Brocade Fabric OS Reference Manual
on the Resource CD.
To make sure that the license has been successfully added to the switch key, run the
licenseshow command. For information about this command, see the Brocade Fabric OS
Reference Manual on the Resource CD.
40
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
A Getting Help and Technical Assistance
This appendix contains information about where to go for additional
information on Intel products, what to do if you experience a problem with
your server platform, and whom to call for service if it is necessary.
Before you call
Before you call, make sure that you have taken these steps to try to solve the
problem yourself:
•
•
•
Check all cables to make sure that they are connected.
Check the power switches to make sure that the system is turned on.
Use the troubleshooting information in your system documentation, and
use the diagnostic tools that come with your system.
You can solve many problems without outside assistance by following the
troubleshooting procedures that Intel provides in the publications that are
provided on the Resource CD that ships with your system and software. The
documentation also describes the diagnostic tests that you can perform. Most
systems, operating systems, and programs come with information that
contains troubleshooting procedures and explanations of error messages and
error codes. If you suspect a software problem, see the information for the
operating system or program.
Using the documentation
Information about your server platform and pre installed software, if any, is
available on the Resource CD that comes with your system. The Resource
CD includes user manuals, maintenance manuals and troubleshooting
guides. See the troubleshooting information in your system documentation
information or the diagnostic programs might tell you that you need
additional or updated device drivers or other software. The troubleshooting
information or the diagnostic programs might tell you that you need
additional or updated device drivers or other software.
Hardware and software service and support
Contact your Intel Support Representative for hardware and software service
and support.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Brocade SAN Switch Module: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|