AutoDome Easy
VEZ Series
en Installation and Configuration Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
| en
iii
Preface
This guide describes how to install the AutoDome Easy.
Audience
This guide is intended for qualified installation and service personnel who are familiar with the applicable national
and local electrical codes.
Document Conventions
Convention
Bold
Meaning
Denotes a part, item, or assembly.
Italic
Underline
courier
Denotes a reference to another paragraph, figure or table.
Used to emphasize a point.
Denotes the actual name of an object, the exact code that should be typed or a message
returned from a system.
Symbols
You may encounter these symbols within the document. Explanatory text accompanies each symbol, which provides
additional information detailing the operation or highlighting safety information.
NOTICE! Notices inform you of essential but non-critical information. Read these messages
carefully as any directions or instructions contained therein can help you avoid making
mistakes.
CAUTION! Cautionary messages provide critical information that help you reduce the chance
of losing data or damaging the system. Please heed these messages.
!
WARNING! Warnings highlight information, that if overlooked may cause damage to the
system or result in personal injury. Take warnings seriously.
!
DANGER! Danger messages denote the presence of electrical equipment that may cause
electric shock or electrocution. Take care when you see this symbol to avoid serious injury or
death.
Bosch Security Systems, Inc.
Installation and Configuration Manual
F01U032279 | December 06, 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
en |
AutoDome Easy
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and
shipping instructions.
Service Centers
USA
Phone: 800-366-2283 or 585-340-4162
Fax: 800-366-1329
Email: [email protected]
Technical Support
Phone: 800-326-1450
Email: [email protected]
CCTV Spare Parts
Phone: 800-894-5215 or 408-957-3065
Fax: 408-935-5938
Email: [email protected]
Canada
Phone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East & Asia Pacific Region
Phone: 44 (0) 1495 274558
Fax: 44 (0) 1495 274280
Email: [email protected]
F01U032279 | December 06, 2006
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions | en
v
10.Power Sources - Operate the unit only from the type of
Important Safeguards
power source indicated on the label. If unsure of the type of
power supply to use, contact your dealer or local power
company.
1. Read, Follow, and Retain Instructions - All safety and oper-
ating instructions should be read and followed before oper-
ating the unit. Retain instructions for future reference.
•For units intended to operate from battery power, refer to
the operating instructions.
2. Heed Warnings - Adhere to all warnings on the unit and in
the operating instructions.
•For units intended to operate with External Power Sup-
plies, use only the recommended approved power supplies.
•For units intended to operate with a limited power source,
this power source must comply with EN60950. Substitu-
tions may damage the unit or cause fire or shock.
•For units intended to operate at 24VAC, normal input volt-
age is 24VAC. Voltage applied to the unit's power input
should not exceed 30VAC.
User-supplied wiring, from the 24VAC supply to unit, must
be in compliance with electrical codes (Class 2 power lev-
els). Do not ground the 24VAC supply at the terminals or at
the unit's power supply terminals.
3. Attachments - Attachments not recommended by the prod-
uct manufacturer should not be used, as they may cause
hazards.
4. Installation Cautions - Do not place this unit on an unstable
stand, tripod, bracket, or mount. The unit may fall, causing
serious injury to a person and serious damage to the unit.
Use only manufacturer-recommended accessories, or those
sold with the product. Mount the unit per the manufac-
turer's instructions. Appliance and cart combination should
be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart combina-
tion to overturn.
11.Coax Grounding - If an outside cable system is connected
to the unit, ensure that the cable system is grounded.
U.S.A. models only - Section 810 of the National Electrical
Code, ANSI/NFPA No.70, provides information regarding
proper grounding of the mount and supporting structure,
grounding of the coax to a discharge unit, size of grounding
conductors, location of discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
5. Cleaning - Unplug the unit from the outlet before cleaning.
Follow any instructions provided with the unit. Generally,
using a damp cloth for cleaning is sufficient. Do not use liq-
uid cleaners or aerosol cleaners.
6. Servicing - Do not attempt to service this unit yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified ser-
vice personnel.
12.Grounding - This unit may be equipped with a 3-wire
grounding plug (a plug with a third pin, for grounding). This
safety feature allows the plug to fit into a grounding power
outlet only. If unable to insert the plug into the outlet, con-
tact an electrician to arrange replacement of the obsolete
outlet. Do not defeat the safety purpose of the grounding
plug.
7. Damage Requiring Service - Unplug the unit from the main
AC power source and refer servicing to qualified service
personnel under the following conditions:
•When the power supply cord or plug is damaged.
•If liquid has been spilled or an object has fallen into the
unit.
•If the unit has been exposed to water and/or inclement
weather (rain, snow, etc.).
•If the unit does not operate normally, when following the
operating instructions. Adjust only those controls specified
in the operating instructions. Improper adjustment of other
controls may result in damage, and require extensive work
by a qualified technician to restore the unit to normal oper-
ation.
•Outdoor equipment should only be connected to the unit's
inputs after this unit has had its grounding plug connected
to a grounded outlet or its ground terminal properly con-
nected to a ground source.
•The unit's input connectors must be disconnected from
outdoor equipment before disconnecting the grounding
plug or grounding terminal.
•Proper safety precautions such as grounding should be fol-
lowed for any outdoor device connected to this unit.
13.Lightning - For added protection during a lightning storm,
or when this unit is left unattended and unused for long
periods of time, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to
the unit due to lightning and power line surges.
•If the unit has been dropped or the cabinet damaged.
•If the unit exhibits a distinct change in performance, this
indicates that service is needed.
8. Replacement Parts - When replacement parts are required,
the service technician should use replacement parts speci-
fied by the manufacturer or that have the same characteris-
tics as the original part. Unauthorized substitutions may
result in fire, electrical shock or other hazards.
9. Safety Check - Upon completion of servicing or repairs to
the unit, ask the service technician to perform safety
checks to ensure proper operating condition.
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
vi en | Safety Precautions
Safety Precautions
For Indoor Product
1. Water and Moisture - Do not use this unit near water -
for example, in a wet basement, in an unprotected out-
door installation or in any area classified as a wet loca-
tion.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
2. Object and Liquid Entry - Never push objects of any kind
into this unit through openings, as they might touch dan-
gerous voltage points or create short circuits, resulting
in a fire or electrical shock. Never spill liquid of any kind
on the unit.
This symbol indicates the presence of uninsulated
“dangerous voltage” within the product’s enclo-
sure that can cause an electric shock.
Power Cord and Power Cord Protection - For units
intended to operate with 230VAC, 50Hz, the input and
output power cord must comply with the latest versions
of IEC Publication 227 or IEC Publication 245.
This symbol indicates the presence of important
operating and maintenance (servicing) instruc-
tions in the literature accompanying the appli-
ance.
3. Power supply cords should be routed so they are not
likely to be walked on or pinched. Pay particular atten-
tion to location of cords and plugs, convenience recep-
tacles, and the point of exit from the appliance.
4. Overloading - Do not overload outlets and extension
cords; this can result in a risk of fire or electrical shock.
Installation should be performed by qualified ser-
vice personnel only in accordance with the
National Electrical Code or applicable local codes.
For Outdoor Product
Power Lines - An outdoor system should not be located
in the vicinity of overhead power lines, electric lights or
power circuits, or where it may contact such power lines
or circuits. When installing an outdoor system, extreme
care should be taken to keep from touching power lines
or circuits, as this contact might be fatal. U.S.A. models
only - refer to the National Electrical Code Article 820
regarding installation of CATV systems.
Power Disconnect. Units with or without ON-OFF
switches have power supplied to the unit when-
ever the power cord is inserted into the power
source; however, the unit is operational only when
the ON-OFF switch is in the ON position. The
power cord is the main power disconnect for all
units.
For Rack-mount Product
Modifications
1. Ventilation - Do not place this equipment in a built-in
installation or rack, unless proper ventilation is pro-
vided, or the manufacturer's instructions were followed.
The equipment must not exceed its maximum operating
temperature requirements.
Caution: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
2. Mechanical Loading - When rack-mounting the equip-
ment, ensure that a hazardous condition is not created
by uneven mechanical loading.
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions | en vii
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only)
Sécurité
Attention : l'installation doit exclusivement être réalisée par du
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, includ-
ing interference that may cause undesired operation.
ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCU-
TION, N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PAN-
NEAU ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN
COMPOSANT SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILI-
SATEUR. CONFIEZ LA RÉPARATION DE L'APPAREIL À DU
PERSONNEL QUALIFIÉ.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules and ICES-003 of Industry Canada. These lim-
its are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and
radiates radio frequency energy, and if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equip-
ment in a residential area is likely to cause harmful interfer-
ence, in which case the user will be required to correct the
interference at his expense.
Ce symbole signale que le produit renferme une «
tension potentiellement dangereuse » non isolée
susceptible de provoquer une électrocution.
Ce symbole invite l'utilisateur à consulter les
instructions d'utilisation et d'entretien (dépan-
nage) reprises dans la documentation qui
accompagne l'appareil.
Intentional or unintentional changes or modifications, not
expressly approved by the party responsible for compliance,
shall not be made. Any such changes or modifications could
void the user’s authority to operate the equipment. If neces-
sary, the user should consult the dealer or an experienced
radio/television technician for corrective action. The user may
find the following booklet, prepared by the Federal Communi-
cations Commission, helpful: How to Identify and Resolve
Radio-TV Interference Problems. This booklet is available from
the U.S. Government Printing Office, Washington, DC 20402,
Stock No. 004-000-00345-4.
Attention: l'installation doit exclusivement être
réalisée par du personnel qualifié, conformément
au code national d'électricité américain (NEC) ou
au code d'électricité local en vigueur.
Coupure de l'alimentation. Qu'ils soient pourvus
ou non d'un commutateur ON/OFF, tous les appar-
eils reçoivent de l'énergie une fois le cordon
branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque le
commutateur est réglé sur ON. Le débranchement
du cordon d'alimentation permet de couper l'ali-
mentation des appareils.
WARNING: This is a Class A product. In a domestic environ-
ment, this product may cause radio interference, in which
case, the user may be required to take adequate measures.
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
viii en | Safety Precautions
Sicherheitshinweise
Precauciones de Seguridad
VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU VER-
MEIDEN, IST DIE ABDECKUNG (ODER RÜCKSEITE) NICHT
ZU ENTFERNEN. ES BEFINDEN SICH KEINE TEILE IN
DIESEM BEREICH, DIE VOM BENUTZER GEWARTET WER-
DEN KÖNNEN. LASSEN SIE WARTUNGSARBEITEN NUR
VON QUALIFIZIERTEM WARTUNGSPERSONAL AUS-
FÜHREN.
PRECAUCIÓN: PARA DISMINUIR EL RIESGO DE DESCARGA
ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PARTE POS-
TERIOR). NO EXISTEN PIEZAS DE RECAMBIO EN EL INTE-
RIOR DEL EQUIPO. EL PERSONAL DE SERVICIO
CUALIFICADO SE ENCARGA DE REALIZAR LAS REPARA-
CIONES.
Das Symbol macht auf nicht isolierte „gefährliche
Spannung" im Gehäuse aufmerksam. Dies kann zu
einem elektrischen Schlag führen.
Este símbolo indica que existen puntos de tensión
peligrosos sin aislamiento dentro de la cubierta de
la unidad. Estos puntos pueden constituir un
riesgo de descarga eléctrica.
Der Benutzer sollte sich ausführlich über
Anweisungen für die Bedienung und Instandhal-
tung (Wartung) in den begleitenden Unterlagen
informieren.
El usuario debe consultar las instrucciones de fun-
cionamiento y mantenimiento (reparación) en la
documentación que se suministra con el aparato.
Achtung! Die Installation sollte nur von qualifizier-
tem Kundendienstpersonal gemäß jeweils zutref-
fender Elektrovorschriften ausgeführt werden.
Atención: la instalación la debe realizar única-
mente personal cualificado de conformidad con el
National Electric Code o las normas aplicables en
su país.
Unterbrechung des Netzanschlusses. Geräte mit
oder ohne Netzschalter haben Spannung am Gerät
anliegen, sobald der Netzstecker in die Steckdose
gesteckt wird. Das Gerät ist jedoch nur betrieb-
sbereit, wenn der Netzschalter (EIN/AUS) auf EIN
steht. Wenn das Netzkabel aus der Steckdose
gezogen wird, ist die Spannungszuführung zum
Gerät vollkommen unterbrochen.
Desconexión de la alimentación. Las unidades con
o sin interruptores de encendido/apagado reciben
alimentación eléctrica siempre que el cable de ali-
mentación esté conectado a la fuente de aliment-
ación. Sin embargo, la unidad sólo funciona
cuando el interruptor está en la posición de
encendido. El cable de alimentación es la principal
fuente de desconexión de todas las unidades.
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions | en ix
Veiligheidsmaatregelen
Sicurezza
VOORZICHTIG: OPEN DE BEHUIZING OF DE ACHTERKANT
VAN HET APPARAAT NIET. ZO VERMINDERT U HET RISICO
OP ELEKTRISCHE SCHOKKEN. IN HET APPARAAT BEVIN-
DEN ZICH GEEN ONDERDELEN DIE U ZELF KUNT REPARE-
REN. LAAT SERVICE EN ONDERHOUD UITVOEREN DOOR
GEKWALIFICEERD PERSONEEL.
ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE
ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL PAN-
NELLO POSTERIORE). L'UNITÀ NON CONTIENE COMPO-
NENTI INTERNI RIPARABILI DALL'UTENTE. PER QUALSIASI
INTERVENTO, RIVOLGERSI A PERSONALE TECNICO QUAL-
IFICATO.
Dit symbool geeft aan dat er binnen in het appa-
raat ongeïsoleerde, gevaarlijke spanning aanwezig
is die mogelijk elektrische schokken kan veroorza-
ken.
Questo simbolo indica la presenza di "tensione
pericolosa" non isolata all'interno del contenitore
del prodotto. Ciò comporta un potenziale rischio
di scosse elettriche.
De gebruiker dient de bedienings- en onderhouds-
voorschriften te raadplegen in de documentatie
die werd meegeleverd met het apparaat.
Si consiglia di consultare le istruzioni operative e
di manutenzione (interventi tecnici) contenute
nella documentazione fornita con il dispositivo.
Attentie: het apparaat mag alleen door gekwalifi-
ceerd personeel worden geïnstalleerd. De instal-
latie dient in overeenstemming met de nationale
elektrische richtlijnen of de van toepassing zijnde
lokale richtlijnen te worden uitgevoerd.
Attenzione: l'installazione deve essere effettuata
esclusivamente da personale tecnico qualificato in
conformità con il National Electrical Code o con le
normative locali vigenti.
Scollegamento dell'alimentazione. Le unità dotate
o sprovviste di interruttori ON-OFF vengono ali-
mentate quando si inserisce il cavo nella presa
dell'alimentazione. L'unità è tuttavia in funzione
solo quando l'interruttore ON-OFF si trova nella
posizione ON. Il cavo di alimentazione costituisce
il dispositivo di scollegamento dell'alimentazione
principale per tutte le unità.
Spanning uitschakelen. Apparatuur met of zonder-
aan-uitschakelaar staat onder spanning zolang de
stekker is aangesloten op de wandcontactdoos.
De apparatuur is uitsluitend in werking als de aan-
uitschakelaar aan staat. Het netsnoer is de "hoofd-
schakelaar" voor alle apparatuur.
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
x
en | Safety Precautions
Medidas de Segurança
Zasady bezpieczenstwa
CUIDADO: PARA REDUZIR O RISCO DE CHOQUE ELÉC-
TRICO, NÃO RETIRE A TAMPA (OU A PARTE POSTERIOR).
NO INTERIOR, NÃO EXISTEM PEÇAS QUE POSSAM SER
REPARADAS PELO UTILIZADOR. REMETA A ASSISTÊNCIA
PARA OS TÉCNICOS QUALIFICADOS.
UWAGA: ZE WZGLEDU NA NIEBEZPIECZENSTWOPORAZE-
NIA PRADEM NIE WOLNO OTWIERAC POKRYWY. W
SRODKU NIE MA ZADNYCH ELEMENTÓW, KTÓRE MOGA
BYC NAPRAWIANE PRZEZUZYTKOWNIKA. NAPRAWE
NALEZY POWIERZYCAUTORYZOWANEMU PUNKTOWI SER-
WISOWEMU.
Este símbolo indica a presença de "tensão peri-
gosa" não isolada dentro da estrutura do produto,
o que pode constituir risco de choque eléctrico.
Blyskawica ze strzalka wewnatrz trójkata równob-
ocznego maza zadanie zwrócic uwage uzytkownika
na obecnoscnieizolowanego “niebezpiecznego
napiecia” wewnatrzobudowy urzadzenia, o wielko-
sci stwarzajacejniebezpieczenstwo porazenia pra-
dem.
O utilizador deve consultar as instruções de funci-
onamento e manutenção (assistência) nos docu-
mentos que acompanham o aparelho.
Wykrzyknik wewnatrz trójkata równobocznego ma
zazadanie zwrócic uwage uzytkownika na waznec-
zynnosci, zwiazane z obsluga i konserwacja urza-
dzenia,zamieszczone w Instrukcji obslugi.
Atenção: a instalação deve ser executada apenas
por técnicos qualificados da assistência, de
acordo com o código eléctrico nacional ou os
códigos locais aplicáveis.
OSTRZEZENIE: ABY UNIKNAC POZARU LUB PORAZENIAPRA-
DEM NIE WOLNO WYSTAWIAC NA DZIALANIE DESZCZU LUB
WILGOCI URZADZEN,KTÓRE NIE ZOSTALY ZAPROJEKTOWANE
DO UZYWANIA SPECJALNIE NA OTWARTYM POWIETRZU.
Corte de corrente. As unidades com ou sem inter-
ruptores ON-OFF (ligar/desligar) recebem cor-
rente sempre que o fio de alimentação está
introduzido na fonte de alimentação; contudo, a
unidade apenas está operacional quando o inter-
ruptor ON-OFF está na posição ON. O fio de ali-
mentação destina-se a desligar a corrente em
todas as unidades.
Uwaga: Instalacje urzadzenia powinien wykonac
tylkowykwalifikowany personel, zgodnie z
przepisami NEClub odpowiednimi przepisami mie-
jscowymi.
Odlaczanie zasilania. Urzadzenia zarówno nie
posiadajace, jaki posiadajace wylaczniki WL-WYL
znajduja sie podnapieciem, jezeli tylko przewód
zasilajacy jest polaczony zezródlem zasilania. Jed-
nakze urzadzenie dziala tylko wtedy, gdywylacznik
znajduje sie w polozeniu WL. Przewódzasilajacy
jestglównym odlacznikiem zasilania dla wszystkich
rodzajówurzadzen.
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions | en xi
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
xii en | Safety Precautions
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Table of Contents | en
xii
Table of Contents
1
Unpacking
1
1.1
1.2
1.3
Parts List
1
1
2
Additional Tools Required
Safety Rules
2
Description
3
3
Installing the AutoDome Easy
3
3.1
Mounting the AutoDome Easy
3
4
Preparing the Wiring
4
4
4
4
5
4.1
4.2
4.3
4.4
Control
Video
Power
Alarm
5
Connections
5
5
5
6
7
7
7
5.1
5.1.1
5.1.2
5.2
5.3
5.4
Connecting to the Biphase
Direct Control
Daisy Chaining
Connecting the Video
Connecting the Power
Connecting the Alarm Input
6
Address (ID)
8
6.1
Setting the Address (ID)
8
7
Setting Protocol and Video Format
10
8
Installing the AutoDome Easy
Surface Mount
11
11
11
12
12
13
13
8.1
8.1.1
8.1.2
8.1.3
8.1.4
8.1.5
Preparing the Drywall Ceiling for Installation
Preparing the Suspension Ceiling for Installation
Installing the Base to the Mounting Plate
Powering On
Installing the Base to a Junction Box
9
Basic Operation
14
14
14
9.1
9.2
Keyboard Control
Command Structure
10
Program and Operation
15
10.1
Menu Navigation
15
Bosch Security Systems, Inc.
Installation and Configuration Manual
F01U032279 | December 06, 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
xiii en | Table of Contents
AutoDome Easy
10.2
Main Menu
15
16
16
17
10.3
Preset Menu
10.3.1
10.3.2
Setting and Saving Presets
Recalling a Preset Position
11
Creating Titles
17
12
Tour Menu
18
18
19
12.1
12.2
Setting a Tour
Running / Stopping a Tour
13
Auto Pan Menu
Set Auto Scans
Run Auto Pan
19
19
20
13.1
13.2
14
Sector Menu
20
15
Alarm Menu
21
15.1
Releasing an Alarm
21
16
Camera Setup Menu
Focus Control Menu
WB Control Menu
AE Control Menu
L/L Control Menu
Picture Menu
22
22
23
24
26
27
27
16.1
16.2
16.3
16.4
16.5
16.6
Initialize Camera Menu
17
Dome Setup Menu
Home Function
28
29
30
30
17.1
17.2
17.3
Initialize Dome Menu
Dome Information Menu
18
19
20
21
Keyboard Commands by Number
Troubleshooting
31
32
32
32
Preventive Maintenance
Spare Parts List
F01U032279 | December 06, 2006
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Unpacking
1
1
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in Section 1.1: Parts List are included. If any items are missing,
notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit and must be
used if returning the unit for service. Save it for possible future use.
1.1
Parts List
The AutoDome Easy includes the following components:
•
•
One (1) PTZ Dome (Dome camera)
One (1) accessory kit including (part number - 9965 300 00648)
One (1) Locking Torx Wrench (T-10)
One (1) Locking Torx Wrench (T-20)
Three (3) tapping screws
Three (3) plastic anchors
•
•
One (1) mounting bracket
One (1) user manual
1.2
Additional Tools Required
•
No. 2 Phillips screwdriver
Bosch Security Systems, Inc.
Installation and Configuration Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
December 06, 2006 | F01U032279
2
Unpacking
AutoDome Easy
1.3
Safety Rules
To ensure safety, the following warnings are specified:
•
•
The device must be installed and maintained by skilled technical personnel.
Connect the device to a power source corresponding to the indications given on the
marking label.
•
•
•
•
•
•
•
Use only the attachments/accessories specified by the manufacturer.
Unplug the device during lightning storms or when unused for long periods of time.
Do not use the device near water.
Do not use the device in the presence of inflammable substances.
Do not allow children or unauthorized personnel to use the device.
Do not block any ventilation openings.
Keep this manual for future reference.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Description
3
2
Description
The AutoDome Easy keyboard controller and camera make up the building blocks for any sur-
veillance/security system. By using multiple keyboard controllers and multiple dome cameras,
no place is too large for monitoring. Extensible and flexible architecture facilities remote con-
trol functions for a variety of external switching devices such as multiplexers and DVRs (see
Figure 2.1 for sample configuration).
Reference # Description
1
2
3
4
5
6
7
8
9
Alarm Input (Sensor)
Multiplexer
RS-485 Cable
J-box
PTZ Dome
PTZ Dome
PTZ Dome
RS-485 Cable
Monitor
10 Keyboard
11 DVR
Fig. 2.1 System Configuration
3
Installing the AutoDome Easy
This chapter outlines the procedures required to install the AutoDome Easy. Installation
should be made by qualified service personnel and conform to all local codes.
3.1
Mounting the AutoDome Easy
The AutoDome Easy can be surface or wall mounted. The appropriate mount should be installed
before installing the AutoDome Easy. For specific directions on mounting the unit, see the man-
ual that came with your mount.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Preparing the Wiring
AutoDome Easy
4
Preparing the Wiring
There are four (4) types of wires required: control, video, power, and alarm. Each section pro-
vides the specifications for the recommended wire.
CAUTION! Installation should only be performed by qualified service personnel in accordance
with the National Electrical Code or applicable local codes.
!
4.1
Control
The control wire from the head end should use a twisted-shielded pair recommended Belden
8760 or equivalent with a maximum length of 1.2 km (4000 ft).
Biphase (shielded 2-wire, half-duplex, multi-drop, 1.2 km (4000 ft.) cable limit), is the stan-
dard Bosch protocol used to send Pan/Tilt/Zoom control over 2-wire shielded twisted pair
(STP). The AutoDome Easy has an internal 110 Ω termination resistor between the biphase(+)
and biphase(-).
The shield connects to the Head End controller and not to theAutoDome Easy.
CAUTION! The biphase shield must be connected to the head end only.
!
Description
Cable Type
Distance
Transmission Rate
Gage
Specification
STP - Shielded Twisted Pair Belden 8760 recommended
1.2 km (4000 ft)
31.25 KHz
1.02 mm (18 AWG)
Internal Termination
Connector
Voltage
110 Ω
Mating connector with flying leads
4 Vp-p
4.2
Video
The video coax cable should use a shield coverage copper braid 95% and standard copper
center conductor. Recommended cables are RG-59, RG-6/U, or RG-11U.
Cable Type
RG-59/U
Maximum Distance
300 m (1000 ft)
RG-6/U
450 m (1500 ft)
RG-11/U
600 m (2000 ft)
Size
O.D. between 4.6 mm (0.181 in.) and 7.9 mm (0.312 in.)
Shield
Central Conductor
Terminal Connector
Copper braid: 95%
Standard copper center
BNC
4.3
Power
The recommended power cable is a 2-conductor, 14-18 gage cable, depending on the dis-
tance. Refer to the wiring distance guide Table 4.1 on page 5.
VA / Watts
10 W
10 W
14 AWG (2.5 mm)
1130 ft(344 m)
285 ft (87 m)
16 AWG (1.5 mm)
711 ft (217 m)
179 ft (55 m)
18 AWG (1.0 mm)
448 ft (137 m)
112 ft (34 m)
24 VAC to AutoDome Easy
12 VD C to AutoDome Easy
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Connections
5
4.4
Alarm
The recommended optional alarm input cable is a 2-conductor, 18-22 gage cable, depending
on the distance. Refer to the wiring distance guide Table 4.1 on page 5.
Wire Size
Maximum Distance
AWG
mm
feet
500
800
meters
152.4
243.8
22
18
0.644
1.024
Table 4.1 Wiring Distance Guide
5
Connections
Follow the instructions below to terminate all connections as described.
Color
Black
Brown
Red
Description
Biphase (+)
Biphase (-)
AC24 V / DC12 V
AC24 V / DC12 V
ALARM COMMON
ALARM IN
Orange
Blue
Violet
Table 5.1 Connection Cable Description
5.1
Connecting to the Biphase
The AutoDome Easy camera can be controlled remotely by an external device or control sys-
tem, such as a control keyboard, using biphase.
5.1.1
Direct Control
To connect the biphase configuration, do the following:
1. Locate the cable assembly with a two (2) pin black mating connector on one end and the
brown and black flying leads on the other end.
2. Connect the biphase+ from the controller to the black lead and secure.
3. Connect the biphase- from the controller to the brown lead and secure.
4. Connect shield of the cable to the Head End controller.
Head End
Biphase
AutoDome Easy
Brown
Black
C-
C+
Not Connected X
SHIELD
Fig. 5.1 Biphase Direct Control
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Connections
AutoDome Easy
5.1.2
Daisy Chaining
In a daisy chain configuration, where multiple domes are connected, the termination switch
must be turned off for all but the last dome. The AutoDome Easy can be daisy chained up to a
maximum of four (4) domes. To daisy chain the unit, do the following:
1. Loosen all bubbles in the daisy chain sequence except for the last one. Use the torx
wrench provided to remove the four (4) tamper-resistant screws on each bubble.
2. Carefully loosen each bubble and allow it to hang from the safety tether.
3. Locate the SW601 switch and slide to the OFF position except for last dome in the chain.
NOTICE! See Section 6: Address (ID) to set the camera ID before replacing the bubble.
4. Locate the cable assembly on the first camera with a two (2) pin black mating connector
on one end and the brown and black flying leads on the other end.
5. Connect the biphase(+) from the controller to the first camera black lead and secure.
6. Connect the biphase(-) from the controller to the brown lead on the first camera and
secure.
7. Connect the biphase(+) from the first camera black lead to the second camera black lead
and secure.
8. Connect the biphase(-) from the first camera brown lead to the second camera brown
lead and secure.
9. Repeat steps as required for up to four (4) cameras.
10. Connect the shield of the cable to the Head End controller. You do not need to connect
the shield to any AutoDome Easy.
Head End
Biphase
Dome 1
Dome 2
Dome 4
Dome 3
Brown
C(-)
C(+)
C(-)
C(+)
C(-)
C(+)
C(-)
C(-)
C(+)
C(+)
SHIELD
Connected
SW601
SW601
SW601
SW601
SW601
Fig. 5.2 Daisy Chain Configuration
SW601
1
Diagram
9
8
7
6
5
4
3
2
1
Terminated
ON
Not Terminated
OFF
N
O
SW601
Table 5.2 Setting the Unit for Termination
December 06, 2006 | F01U032279
Installation and Configuration Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems, Inc.
AutoDome Easy
Connections
7
5.2
Connecting the Video
Coaxial cable terminated with BNC connectors is the most common method for transmitting
composite video. To connect the video, do the following:
1. Terminate the coaxial cable from the head end system with a male BNC connector.
2. Connect the head end video cable to the yellow Video Out connector from the base of the
camera.
5.3
Connecting the Power
To connect the power, do the following:
WARNING! This unit accepts 24 VAC or 12 V DC, 1 A power only. Do not connect 120 V or
230 V to this camera.
!
1. Locate the cable assembly with a two (2) pin mating connector on one end and the
orange and red flying leads on the other end.
2. Connect one lead of the 12 V DC or 24 VAC power source to the red wire.
3. Connect one lead of the 12 V DC or 24 VAC power source to the orange wire.
NOTICE! Use certified / Listed Class 2 power supply transformer only.
5.4
Connecting the Alarm Input
The AutoDome Easy provides one (1) alarm input. This alarm input can be activated by dry
contact devices, which triggers the dome camera to move to a pre-position. The default alarm
state is normally open but may be programmed to be normally closed. See
Section 10: Program and Operation for configuring alarm input. To connect the alarm input, do
the following:
1. Locate the cable assembly with a two (2) pin blue mating connector on one end and the
blue and violet flying leads on the other end.
2. Connect the ground of the alarm source dry contact to the blue wire (alarm common).
3. Connect the alarm out of the alarm source dry contact to the violet wire (alarm input).
Alarm Common Blue Wire
Dry
C
o
n
tact
Alarm Input Violet Wire
Fig. 5.3 N.O. - Normally Open Non-supervised Connections
NOTICE! All the connectors marked GND are common.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Address (ID)
AutoDome Easy
6
Address (ID)
Each AutoDome Easy camera must have a unique address (ID). When installing multiple dome
cameras using a DVR, it is suggested that the dome camera address match the DVR input num-
ber (for example: Input 1 = Dome 1, Input 2 = Dome 2, etc...). Set a unique camera address
(ID) using the switch selections inside the bubble.
6.1
Setting the Address (ID)
To set the unique AutoDome Easy ID address, do the following:
1. Loosen the bubble’s four (4) tamper-resistant screws using the torx wrench provided.
2. Carefully lift the bubble and set it aside.
3. Locate the SW501 switch.
4. Set the switches based on Table 6.1.
Fig. 6.1 Setting the AutoDome Easy Address (ID)
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Address(ID)
9
ID
Address
1
SW1 SW2 SW3 SW4 SW5 SW6
ID
SW1 SW2 SW3 SW4 SW5 SW6
Address
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON
OFF ON
ON ON
OFF OFF OFF OFF ON
2
OFF
ON
OFF OFF OFF ON
OFF OFF OFF ON
3
ON
4
OFF
ON
OFF
OFF
ON
OFF OFF ON
ON OFF ON
OFF ON
ON ON
OFF OFF ON
OFF OFF ON
OFF OFF ON
OFF OFF ON
5
ON
6
OFF
ON
ON
ON
ON
7
ON
ON
8
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF OFF OFF ON
ON OFF OFF ON
OFF ON
ON ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
9
ON
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
OFF
ON
ON
OFF ON
OFF ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
OFF OFF ON
ON OFF ON
OFF ON
ON ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF OFF OFF OFF ON
ON OFF OFF OFF ON
OFF ON
ON ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF OFF ON
OFF OFF ON
ON
OFF
ON
OFF
OFF
ON
OFF OFF ON
ON OFF ON
OFF ON
ON ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF OFF OFF ON
ON OFF OFF ON
OFF ON
ON ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
OFF ON
OFF ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
OFF OFF ON
ON OFF ON
OFF ON
ON ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF ON
Table 6.1 ID Settings
Bosch Security Systems, Inc.
Installation and Configuration Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
December 06, 2006 | F01U032279
10 Setting Protocol and Video Format
AutoDome Easy
7
Setting Protocol and Video Format
The factory default settings for switches 8, 9, and 0 are set for the correct operation. How-
ever, if the camera is operating incorrectly, the proper configuration is the following:
•
Switch 8 - set to match the appropriate video format;
NTSC (60 Hz) ON
- or -
PAL (50 Hz) OFF.
•
Switches 9 and 0 - set to biphase protocol (see Table 7.1).
NOTICE! The error message: PROTOCOL IS NOT MATCHED is displayed during the power-up
cycle if switches 9 and 0 are not set correctly.
Dome Camera
Function
Black = ON
Dome Camera
Protocol Function
Fig. 7.1 AutoDome Easy Camera Function and Protocol Selection Switches
S/W No. ON
NTSC
OFF
Function
8
PAL
NTSC/PAL
Table 7.1 Dome Camera Function
No. 9
No. 0
Protocol
ON
OFF
Biphase
Table 7.2 Dome Camera Protocol Function
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Installing the AutoDome Easy
11
8
Installing the AutoDome Easy
This chapter details how to install the AutoDome Easy for an in-ceiling, wall, or pipe mount.
8.1
Surface Mount
The mounting plate (included) is used for ceiling installation. The unit may be mounted to a
hard surface or to a suspended ceiling tile.
NOTICE! The image sensors in modern CCD cameras are highly sensitive and require special
care for proper performance and extended lifetime. Follow the guidelines for optimum results
with your camera:
•
Do not expose to direct sunlight or bright spotlights in operating and nonoperating
conditions.
•
Avoid bright lights in the field of view of the camera. Bright lights cause a "smearing"
effect, which is visible as white lines above and below the highlight. Prolonged expo-
sure to bright lights may cause bleaching of the sensor's color filters. This will be vis-
ible as colored spots in the picture and is irreversible.
1
2
3
4
5
4
6
Fig. 8.1 Ceiling Mount Installation
Reference #
Description
1
2
3
4
5
6
7
Mounting Holes
Plastic Mounting Anchor
Front (Locking Tab)
Cable Hole (40 mm maximum)
Indentation
Mounting Bracket
M4 x 25 Tapping Screws
8.1.1
Preparing the Drywall Ceiling for Installation
To mount to a surface, follow the steps below:
1. Determine a proper location for the dome.
2. Use the supplied mounting bracket as a template to mark the three (3) mounting hole
locations on the ceiling.
3. Locate the curved indentation (see Figure 8.1, Reference # 5) to mark the center of the
hole.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Installing the AutoDome Easy
AutoDome Easy
4. Drill or cut the appropriate size hole required for the cables.
5. Drill the appropriate holes for the supplied anchors.
6. Insert the anchors.
7. Position the locking tab, as seen in Figure 8.1 reference #3, of the mounting plate facing
the center toward the field of view for a 180 degree position.
8. Secure the mounting plate to the ceiling with the supplied screws.
8.1.2
Preparing the Suspension Ceiling for Installation
To mount to a rigid suspended ceiling, follow the steps below:
NOTICE! To avoid sagging ceiling tiles, the weight of the dome (approximately 2 lb) and all
necessary wiring must be evenly supported.
1. Determine a proper location for the dome, and remove an adjacent ceiling tile.
2. Use the supplied mounting bracket as a template to mark the three (3) mounting hole
locations on the ceiling.
3. Locate the curved indentation (see Figure 8.1, Reference # 5) to mark the center of the
hole.
4. Drill or cut the appropriate size hole required for the cables.
5. Drill the appropriate holes for the mounting screws (not supplied).
6. Orient the locking tab, as seen in Figure 8.1 reference #3, of the mounting plate facing
the center toward the field of view for a 180 degree position.
7. Secure the mounting plate to the ceiling with the appropriate screws (not supplied).
8.1.3
Installing the Base to the Mounting Plate
To install the base to a drywall or suspended ceiling using the supplied mounting plate, do the
following:
1. Align the supplied mounting bracket with the cut cable hole.
2. Attach the mounting bracket to the ceiling using the supplied three (3) tapping screws.
3. Unlock the safety locking screw using the supplied Allen wrench.
4. Extract each wire through the cable hole.
5. Hang the dome camera to the mounting bracket using the safety wire.
6. Connect the prepared wiring in Section 5: Connections matching the colors of the wires.
Fig. 8.2 Connecting the Cables
7. Align the dome camera with the mounting bracket.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Installing the AutoDome Easy
13
Fig. 8.3 Installing the Dome
8. Turn the dome camera to the right approximately 15 degrees.
9. Secure the safety locking screw.
8.1.4
Powering On
When AutoDome Easy’s power is turned on, there is a five (5) second pause before the dome
starts its homing phase. During the homing phase, the camera pans left and right and tilts up
and down. It also adjusts the lens focus. The entire homing phase lasts approximately 40 sec-
onds and displays the following splash screen throughout its homing phase START UP BOSCH
Version 2.0.x.
NOTICE! The error message: PROTOCOL IS NOT MATCHED is displayed during the power-up
cycle if switches 9 and 0 are not set correctly.
8.1.5
Installing the Base to a Junction Box
If it is not possible to drill a hole in the ceiling for wiring, it is recommended to use a junction
box (not supplied). To mount a junction box, follow all standard procedures.
NOTICE! This mounting method does not require use of the supplied mounting plate.
To install the AutoDome Easy to a junction box, follow the steps below:
1. Carefully loosen the bubble by using the torx wrench provided to remove the four (4)
tamper-resistant screws. Allow the bubble to hang from the safety tether.
2. Remove the appropriate two (2) (see Figure 8.4) black rubber plugs from the camera
base.
Fig. 8.4 Removing the Plugs from the Camera Base
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Basic Operation
AutoDome Easy
3. Connect the prepared wiring in Section 5: Connections matching the colors of the wires.
4. Align the two (2) screws (not provided) with the junction box and secure the dome.
5. Re-attach the bubble.
9
Basic Operation
This section describes how to use the keyboard and details the keyboard command structure.
9.1
Keyboard Control
The following tables summarize the basic operations for a standard keyboard and the func-
tions available to control an AutoDome Easy camera.
Typical Keyboard
Features
Usage
Function Keys
Number Keys
Camera Key
Enter Key
Focus Key
Iris Key
Selects a specific control setting.
Inputs a number from 0 to 9.
Selects a camera number.
Inputs a selection.
Sets the lens focus or makes a menu selection in OSD mode.
Sets the lens iris setting or makes a menu selection in OSD mode.
Indicates an active key.
Key LEDs
LCD
Displays the current status.
Joystick
Controls a pan, tilt, and zoom AutoDome camera.
Table 9.1 Typical Keyboard Functions
Dome Operation
To Pan Side to Side
To Tilt Up and Down
To Zoom In
How to control
Move the joystick left or right.
Move the joystick forward and back.
Twist the joystick clockwise.
To Zoom Out
Twist the joystick counterclockwise.
Table 9.2 Typical Keyboard Controls for an AutoDome Easy Camera
9.2
Command Structure
Keyboard control commands are composed of a sequence of three (3) inputs with the follow-
ing convention: 1) a Function key + 2) a Command number key(s) + 3) the Enter key.
Depending on the type of keyboard, the control function keys are labeled:
•
•
•
•
ON or AUX ON
OFF or AUX OFF
SET or SET SHOT
SHOT or SHOW SHOT
December 06, 2006 | F01U032279
Installation and Configuration Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems, Inc.
AutoDome Easy
Program and Operation
15
10
Program and Operation
The AutoDome Easy is programmed through the on-screen display (OSD) menus. Each on-
screen display (OSD) shows a list of parameters or submenus that can be selected by the
operator.
10.1
Menu Navigation
To access the OSD menus, open the Main menu by pressing ON + 4 + 6 + ENTER.
NOTICE! The main menu can not be accessed when an auto pan or preset tour is running.
Press the joystick in any direction to stop the tour or auto pan.
Use the joystick to navigate through the menu. To navigate throughout the OSD menus, do the
following:
•
•
•
To scroll through the parameters, move the joystick upꢀ
ꢁ
To edit the parameters or enter a submenu, move the joystick left
and down .
and right
ꢂ
.
To exit the submenu, move the cursor to EXIT, then move the joystick to the right
ꢂ
.
10.2
Main Menu
The Main menu provides access to all programmable AutoDome Easy settings. Press ON + 4 +
6 + ENTER to display the Main menu.
MAIN MENU
PRESET
TOUR
AUTO PAN
SECTOR
ALARM
CAMERA SETUP
DOME SETUP
EXIT
Menu
Description
Preset
Pre-selects and stores combinations of pan, tilt and zoom positions which allow a
set view to be recalled. Also known as preset shot.
Tour
Accesses a sequence of preset shots combined to provide a pre-programmed tour
of the area covered by an AutoDome Easy camera.
Auto Pan
Sector
Accesses a range of 1-4 for customized auto pan tours.
Breaks the total 360 degrees into eight sectors of 45 degrees each. Individual titles
may be assigned to each sector.
Alarm
Accesses the alarm settings such as: input type, timeout options, and dwell time.
Accesses adjustable camera settings such as: white balance, gain, sharpness, sync,
backlight, and shutter.
Camera Setup
Dome Setup
Exit
Controls miscellaneous dome operations such as: OSD, auto pivot, home function,
and initialization (reset to factory defaults).
Exits the menu without saving the data.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
16 Program and Operation
AutoDome Easy
10.3
Preset Menu
The preset menu is designed to create and edit up to 60 sequential preset titles. The preset
must be saved prior to editing a title see section Section 10.3.1: Setting and Saving Presets.
MAIN MENU
PRESET
TOUR
AUTO PAN
SECTOR
PRESET MENU
NUMBER: 01
TITLE: Scene 1
0/1234567890
--- ** ** *=====
1/1234567890
--- ==========
2/1234567890 3/1234567890
- ========== - ==========
4/1234567890 5/1234567890
ALARM
CAMERA SETUP
DOME SETUP
EXIT
- ==========
- ==========
SAVE AND EXIT
EXIT W/O SAVE
Menu
Description
Number
Represents the presets which have been saved. Twisting the joystick with a preset
number highlighted moves the camera to the saved preset location.
Controls a 10-character scene name which is displayed when the AutoDome Easy
moves to a scene (must be user defined via the Title OSD).
Indicates the preset shot saved with a “*” symbol below the number.
Saves the data and exits the menu.
Title
#/1234567890
Save and Exit
Exit W/O Save
Exits the menu without saving the data.
NOTICE! Saving data is temporary. To save data permanently, select the SAVE AND EXIT
command.
10.3.1
Setting and Saving Presets
The AutoDome Easy is designed to save up to 60 preset locations. Each preset location has a
pan/tilt/zoom data capability which is defined by the user. To set a preset position, do the fol-
lowing:
1. Exit the OSD menu.
2. Move the joystick to the desired preset position.
3. Press Set + (1-60) + ENTER.
A message, PRESET SAVING...is displayed on the screen.
If the user attempts to save over an existing preset shot, a confirmation message is dis-
played: OVERWRITE CURRENT SCENE?
NOTICE! If the message, Out of Sequence is displayed, a preset save is being attempted that
is not available. All preset positions must be set in sequential order. To verify the next number
in the sequence, enter the Preset menu and scroll through the saved presets. The last number
displayed is the next available preset position.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
CreatingTitles
17
10.3.2
Recalling a Preset Position
The AutoDome Easy is designed to recall up to 60 preset locations.
To recall a preset position do the following:
ꢃ
Press Shot + (screen shot # 1-60) + ENTER. The AutoDome Easy displays the preset posi-
tion with a user defined title in the upper left-hand corner. If the user attempts to recall a
shot that has not been preset, an error, DATA NOT PROGRAMMEDis displayed on the
screen.
NOTICE! The preset position can not be accessed when an auto pan or preset tour is running.
Press the joystick in any direction to stop the tour or auto pan.
11
Creating Titles
The AutoDome Easy is designed to display a user defined title for individual preset locations,
preset tours, and auto pan tours. To insert a title, do the following:
1. Press ON + 4 + 6 + ENTER to access the main menu.
2. Select PRESET, TOUR, or AUTO PAN.
3. Select the appropriate number for the preset, preset tour, or auto pan to be edited.
4. Select the TITLE: ========== field, twist the joystick. A character is displayed and the
cursor starts blinking indicating it is in edit mode.
5. Twist the joystick knob to the right or left to begin scrolling through the characters. Twist
the joystick right to go forward or twist the joystick knob left to go backwards.
6. Press the joystick to the right after reaching the desired letter or number. The letter
stops blinking. The next sequential character is changed to a blank space, twist the joy-
stick and repeat step 5.
7. When satisfied with the title, select SAVE AND EXIT. To exit without saving, select
EXIT W/O SAVE.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Tour Menu
AutoDome Easy
12
Tour Menu
The Tour menu provides access to preset tours that are customized to run a sequence of user
selected presets.
MAIN MENU
PRESET
TOUR MENU
TOUR: 1
TOUR
AUTO PAN
SECTOR
TITLE: ==========
DWELL TIME: 05 SEC
01 03 05 = = = =
= = = = = = = =
DELETE DATA
SAVE AND EXIT
EXIT W/O SAVE
ALARM
CAMERA SETUP
DOME SETUP
EXIT
Menu
Description
Tour
Accesses a sequence of preset shots combined to provide a pre-programmed tour
of the area covered by an AutoDome Easy camera.
Title
Controls a 10-character scene name which is displayed when the AutoDome Easy
runs the preset tour (must be user defined via the Title OSD).
Allows a range of 5-99 sec. The camera pauses at each preset for the specified
amount of time. Default is 5.
Dwell Time
01 03 05 = = = =
= = = = = = = =
Delete Data
Controls a customized sequence of preset shots which are combined to provide a
pre-programmed tour of the area covered by an AutoDome Easy camera.
Deletes the previously saved tour.
Save and Exit
Exit W/O Save
Saves the data and exits the menu.
Exits the menu without saving the data.
12.1
Setting a Tour
The AutoDome Easy is designed to set up to four (4) customized sequences of preset shots
covered by the AutoDome Easy camera. To set a tour, do the following:
1. Press ON + 4 + 6 + ENTER to access the main menu.
2. Select TOUR.
3. Select desired tour number (1-4).
4. To edit the title see Section 11: Creating Titles.
5. Select the DWELL TIME field.
6. Press the joystick right to increase the time or left to decrease the time.
7. Select the ========== field, to set the sequence of preset shots. Twist the joystick knob.
A number is displayed and the cursor starts blinking indicating it is in edit mode.
8. Twist the joystick to the right or left to begin scrolling through the saved presets. Twist
the joystick right to go forward or twist the joystick left to go backwards.
9. Press the joystick to the right after reaching the desired number. The number stops blink-
ing. The next sequential number is changed to blinking = =, twist the joystick and repeat
step 8.
10. When satisfied with the preset tour, select SAVE AND EXIT. To exit without saving, select
EXIT W/O SAVE.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Auto Pan Menu
19
12.2
Running / Stopping a Tour
The AutoDome Easy is designed to display a customized sequence of preset shots covered by
the AutoDome Easy camera. To run a tour, do the following:
1. Press SHOT + 2 + 0 + (pre-defined tour #) + ENTER.
For example, to run tour 3, press SHOT + 2 + 0 + 3 + ENTER.
2. To stop a tour, move the joystick in any direction.
NOTICE! A shortcut is available for tour 1. Press ON + 8 + ENTER.
13
Auto Pan Menu
The Auto Pan function is designed to pan continuously between right and left limit settings.
This menu provides access to the starting point, ending point, tilt and zoom, and a customized
title feature.
MAIN MENU
PRESET
TOUR
AUTO PAN
SECTOR
AUTO PAN MENU
AUTO PAN: 1
TITLE: ==========
START POINT:
TILT AND ZOOM
END POINT:
017.0
002.6
176.9
ALARM
CAMERA SETUP
DOME SETUP
EXIT
SAVE AND EXIT
EXIT W/O SAVE
Menu
Description
Auto Pan
Title
Accesses a range of 1-4 for customized auto pan tours.
Controls a 10-character scene name which is displayed when the AutoDome Easy
runs the auto pan tour (must be user defined via the Title OSD).
Sets the left pan limit to start panning.
Start Point
Tilt and Zoom
Controls the camera movement in the vertical direction and the changing of the
effective focal length to allow different fields of view to fill the picture area. Zoom
can be optical, where the lens is adjusted, or digital, where a portion of the view
selected is magnified electronically.
End Point
Sets the right limit to stop panning.
Save and Exit
Exit W/O Save
Saves the data and exits the menu.
Exits the menu without saving the data.
13.1
Set Auto Scans
1. Press ON + 4 + 6 + ENTER to access the main menu.
2. Select AUTO PAN.
3. Select AUTO PAN and select the pan number (1-4).
4. To edit the title see Section 11: Creating Titles.
5. Select START POINT.
6. Press ON + 5 + ENTER to gain access of the CONTROL. When finished selecting the cam-
era’s starting point, press OFF + 5 + ENTER.
7. Select TILT AND ZOOM.
8. Press ON + 5 + ENTER to gain access of the CONTROL. When finished selecting the cam-
era’s tilt and zoom, press OFF + 5 + ENTER.
9. Select END POINT.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Sector Menu
AutoDome Easy
10. Press ON + 5 + ENTER to gain access of the CONTROL. When finished selecting the cam-
era’s end point, press OFF + 5 + ENTER.
11. When satisfied, select SAVE AND EXIT. To exit without saving, select EXIT W/O SAVE.
13.2
Run Auto Pan
The AutoDome Easy is designed to display a customized auto pan between limits. To run the
auto pan feature, do the following:
1. Exit the OSD menu.
2. Press Shot + 3 + 0 + (Auto Pan number) + ENTER. For example, to run the auto scan for
course 4, press Shot + 3 + 0 + 4 + ENTER. Note: This is invalid if in menu mode.
NOTICE! Two shortcuts are available for auto pan.
Press ON + 1 + ENTER to activate a continuous pan from 0 to 360 degrees starting at the cur-
rent tilt and zoom positions.
Press ON + 2 + ENTER to activate auto pan 1.
14
Sector Menu
The sector function provides access to customizing individual sectors and titles. The factory
default is eight (8) evenly spaced sectors with titles from SECTOR1 to SECTOR8.
MAIN MENU
PRESET
TOUR
AUTO PAN
SECTOR
SECTOR MENU
SECTOR: 1
TITLE: ==========
START POINT:
END POINT:
017.0
176.9
ALARM
DELETE DATA
SAVE AND EXIT
EXIT W/O SAVE
CAMERA SETUP
DOME SETUP
EXIT
Menu
Description
Sector
Title
Accesses a range of 1-8 for customized sectors.
Controls a 10-character scene name which is displayed when the AutoDome Easy
pans in any direction (must be user defined via the Title OSD).
Sets the left pan limit to display the sector title.
Sets the right limit to display the sector title.
Start Point
End Point
Delete Data
Save and Exit
Exit W/O Save
Deletes the previously saved sectors.
Saves the data and exits the menu.
Exits the menu without saving the data.
NOTICE! Sector titles are displayed any time the camera moves and disappears three (3)
seconds after the camera stops.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
AlarmMenu
21
15
Alarm Menu
The Alarm menu provides access to edit the alarm options.
MAIN MENU
PRESET
TOUR
ALARM MENU
INPUT: NO
OPTION: MOMENTARY
AUTO PAN
SECTOR
ALARM
CAMERA SETUP
DOME SETUP
EXIT
PRESET: 05
DWELL TIME
SAVE AND EXIT
EXIT W/O SAVE
Menu
Description
Options
Default
Input
Defines the type of physical
input.
NC - Normally Closed
NO - Normally Open
OFF - Alarm input is disregarded
OFF
Option
Defines the mode of operation. Time Out - Upon alarm activation, the cam- Time Out
era moves to the defined preset and
remains in alarm for the specified dwell
time. When the time has expired the cam-
era reverts back to the previous operation
prior to the alarm being activated.
Momentary - Upon alarm activation, the
camera moves to the pre-defined preset
position and remains in alarm mode until
OFF + 65 + ENTER is pressed. After the
alarm is acknowledged, the camera reverts
back to the previous operation prior to the
alarm being activated.
Preset
Moves to the defined preset,
upon alarm activation,
All saved presets are available.
1
5
Dwell Time
In time out mode, the camera
remains in alarm mode for the
specified dwell time.
Allows a range of 5-99 sec.
Save and Exit
Saves and exits the menu.
Exit W/O Save Exits the menu without saving the
data.
15.1
Releasing an Alarm
There are two modes of operation. Time out releases the alarm after the dwell time. However,
time out may also be released by pressing OFF + 6 + 5 + ENTER. Momentary can only be
released with the following sequence: press OFF + 6 + 5 + ENTER.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Camera Setup Menu
AutoDome Easy
16
Camera Setup Menu
The Camera Setup menu provides access to lens settings that can be changed or customized.
MAIN MENU
PRESET
TOUR
CAMERA SETUP MENU
FOCUS CONTROL
WB CONTROL
AUTO PAN
SECTOR
ALARM
AE CONTROL
L/L CONTROL
PICTURE
CAMERA SETUP
DOME SETUP
EXIT
INITIALIZE CAMERA
EXIT W/O SAVE
Menu
Description
Focus Control
WB Control
AE Control
Controls the focus mode and digital zoom.
Controls the white balance mode.
Controls the auto exposure options.
L/L Control
Picture
Controls access between changing line lock and crystal mode.
Controls the mirror and sharpness settings.
Resets to the default settings for the camera setup menu only.
Exits the menu without saving the data.
Initialize Camera
Exit W/O Save
16.1
Focus Control Menu
The Focus Control menu provides access for mode, focal distance, and digital zoom.
CAMERA SETUP MENU
FOCUS CONTROL
WB CONTROL
AE CONTROL
L/L CONTROL
PICTURE
FOCUS CONTROL MENU
MODE: MANUAL
DISTANCE: 0.1M
DIGITAL ZOOM: OFF
SAVE AND EXIT
EXIT W/O SAVE
INITIALIZE CAMERA
EXIT
Menu
Mode
Description
Options
Default
Selects either manual or auto focus Manual - Controls the focus using the key-
Manual
control.
board buttons.
Auto - Automatically focuses the camera as
the camera is moved.
Distance
Limits the focus range of the camera. Allows a range of 0.1, 1.0, 1.5, 2.5, 6.0 m.
The camera will not focus on any
0.1 m
object within the specified limit.
Digital Zoom
Activates the digital imaging technol- ON - Provides an additional 10x digital zoom. OFF
ogy to increase the range beyond the OFF - Turns off digital zoom.
optical zoom.
Save and Exit Saves the data and exits the menu.
Exit W/O Save Exits the menu without saving the
data.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Camera Setup Menu
23
16.2
WB Control Menu
The WB Control menu provides access to the white balance modes which includes auto,
indoor, outdoor, and manual.
CAMERA SETUP MENU
FOCUS CONTROL
WB CONTROL
AE CONTROL
L/L CONTROL
PICTURE
WB CONTROL MENU
MODE: AUTO
R-GAIN:
B-GAIN:
SAVE AND EXIT
EXIT W/O SAVE
INITIALIZE CAMERA
EXIT
Menu
Mode
Description
Maintains proper color reproduction Indoor - Optimizes camera color for
as the color temperature of a scene typical indoor conditions.
changes. For example, from daylight to Outdoor - Optimizes camera color for
Options
Default
Auto
fluorescent lighting.
typical outdoor conditions.
Manual - Manually adjusts the cam-
era’s output color independent of the
lighting used.
Auto - Automatically adjusts the output
color to display a natural color inde-
pendent of the lighting used.
Allows a range of 0-255.
R-Gain
B-Gain
Adjusts the red gain to optimize the
white point. Available in manual mode
only.
*
*
Adjusts the blue gain to optimize the Allows a range of 0-255.
white point. Available in manual mode
only.
Save and Exit
Exit W/O Save
Saves the data and exits the menu.
Exits the menu without saving the
data.
*Automatically adjusts the camera to the current light level, when in manual mode.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
24 Camera Setup Menu
AutoDome Easy
16.3
AE Control Menu
The AE Control menu provides access to auto exposure options which includes modes, iris,
gain, shutter, and brightness.
CAMERA SETUP MENU
FOCUS CONTROL
WB CONTROL
AE CONTROL
AE CONTROL MENU
MODE: AUTO
IRIS:
GAIN:
L/L CONTROL
PICTURE
INITIALIZE CAMERA
EXIT
SHUTTER:
BRIGHT: 30
BACK LIGHT: OFF
SAVE AND EXIT
EXIT W/O SAVE
Menu
Description
Options
Default
Auto - The camera automatically adjusts iris, gain, and AUTO
shutter speeds. Brightness may be pre-defined.
Shutter PRI - The camera automatically adjusts iris and
gain. The shutter and brightness may be pre-defined.
Iris PRI - The camera automatically adjusts the gain
and shutter. The iris and brightness may be pre-
defined.
Mode
Provides gain control
modes.
Manual - The camera operates in the manual mode.
The iris, gain, and shutter must be pre-defined.
Flickerless - The camera automatically removes flicker,
when camera signal format does not coincide with the
power source frequency. For example, when an NTSC
camera is used with 50 Hz power.
Iris
Controls the lens's F stop
value to manually adjust
for various light levels.
Available with iris PRI
and manual mode only.
F2.8
F1.8, 2, 2.4, 2.8, 3.4, 4, 5.6, 6.8, 8, 9.6, 11, 14,
16, 19, 22, CLOSE
Gain
Electronics that regulate Allows a range of 0-30.
the gain or amplification
of the video signal. Avail-
able in manual mode
0
only.
Shutter
Bright
Manually adjusts the
NORMAL (60 NTSC and 50 PAL), 100, 120, 250, 500, 100
shutter speed. Available 1000, 2000, 5000, 10000
in shutter PRI and man-
ual mode only.
Reduces the camera's iris Allows a range of 0-90.
level for proper expo-
30
sure.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Camera Setup Menu
25
Menu
Description
Options
Default
Back Light
Selectively amplifies
parts of the image to
compensate for large
contrast differences
when only a portion of
the image is brightly lit
(e.g. a person in a sunlit
doorway).
ON, OFF
OFF
Save and Exit
Exit W/O Save
Saves the data and exits
the menu.
Exits the menu.
Mode
Iris
Gain
Shutter
Brightness
Back Light
Auto
z
z
z
z
z
z
z
Shutter PRI
Iris PRI
Manual
z
z
z
z
z
Table 16.1 Mode Options
Bosch Security Systems, Inc.
Installation and Configuration Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
December 06, 2006 | F01U032279
26 Camera Setup Menu
AutoDome Easy
16.4
L/L Control Menu
The L/L Control menu provides access to the sync mode which includes external and internal.
CAMERA SETUP MENU
FOCUS CONTROL
WB CONTROL
AE CONTROL
L/L CONTROL
PICTURE
L/L CONTROL MENU
MODE: INTERNAL
PHASE:
SAVE AND EXIT
EXIT W/O SAVE
INITIALIZE CAMERA
EXIT
Menu
Mode
Description
Selects the sync mode.
Options
Default
Internal - Synchronizes camera to an Internal
internal crystal. This choice is recom-
mended if there is noise on the power
line.
External - Synchronizes camera to AC
power. This choice eliminates picture
roll in multi-camera systems.
Phase
Optimizes the line lock mode to Allows a range 0-620 (PAL).
Automatically
adjusts to the AC
power line.
eliminate picture roll in mul-
tiphase power applications.
Saves the data and exits the
menu.
Allows a range 0-519 (NTSC).
Save and Exit
Exit W/O Save
Exits the menu without saving
the data.
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Camera Setup Menu
27
16.5
Picture Menu
The Picture menu provides access to miscellaneous video settings which includes mirror and
sharpness.
CAMERA SETUP MENU
FOCUS CONTROL
WB CONTROL
AE CONTROL
L/L CONTROL
PICTURE
PICTURE MENU
MIRROR: OFF
SHARPNESS: 09
SAVE AND EXIT
EXIT W/O SAVE
INITIALIZE CAMERA
EXIT
Menu
Description
Selects a mirror image.
Options
Default
OFF
8
Mirror
ON, OFF
Sharpness
Adjusts the sharpness of the pic- Allows a range of 0-15.
ture.
Save and Exit
Exit W/O Save
Saves the data and exits the
menu.
Exits the menu without saving
the data.
16.6
Initialize Camera Menu
The Initialize Camera menu allows you to reset all camera settings to the default setting. Press
the joystick to the right to display the following message: CAMERA WILL BE INITIALIZED!! ARE
YOU SURE?
CAMERA SETUP MENU
CAMERA WILL BE INITIALIZED!!
ARE YOU SURE?
FOCUS CONTROL
WB CONTROL
AE CONTROL
L/L CONTROL
PICTURE
NO
YES
INITIALIZE CAMERA
EXIT
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Dome Setup Menu
AutoDome Easy
17
Dome Setup Menu
The Dome Setup menu provides access to miscellaneous camera parameters which includes:
language, OSD, auto pivot, home function, initialization, and dome information.
MAIN MENU
PRESET
TOUR
AUTO PAN
ALARM
CAMERA SETUP
DOME SETUP
EXIT
DOME SETUP MENU
LANGUAGE: ENGLISH
OSD DISPLAY: OFF
AUTO PIVOT: ON
HOME FUNCTION
INITIALIZE DOME
DOME INFORMATION
SAVE AND EXIT
EXIT W/O SAVE
Menu
Description
Options
Default
Language
Selects the language for the OSD menu. English, Espanol, and English
Francais
OSD Display
Controls the information displayed by the ON - Displays the
OFF
OSD.
dome address, sector
title, and the camera
position data.
OFF - Displays sec-
tor titles only.
Auto Pivot
Automatically turns the AutoDome Easy ON, OFF
camera 180 degrees when the camera
tilts to its lowest position. When the cam-
era vertically reaches 90 degrees, it
stops. Release the joystick, then press
down to activate the flip function.
Selects the mode that the camera reverts
to after a period of inactivity to the
defined dwell time.
ON
Home Function
Initialize Dome
Resets to the default settings for all
menus.
YES, NO
N/A
Dome Information
Save and Exit
Displays the firmware version number.
Saves the data and exits the menu.
Exits the menu without saving the data.
Exit W/O Save
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Dome Setup Menu
29
17.1
Home Function
The Home Function menu can be set so that the camera automatically goes to preset, tour, or
auto pan after the keyboard controller has been in idle for a specified amount of time. For
example, if the joystick controller has not been used for 10 seconds, the camera goes to pre-
set 1.
DOME SETUP MENU
LANGUAGE: ENGLISH
OSD DISPLAY: OFF
AUTO PIVOT: ON
HOME FUNCTION
INITIALIZE DOME
DOME INFORMATION
SAVE AND EXIT
HOME FUNCTION MENU
MODE: OFF
FUNCTION TYPE:
FUNCTION NUMBER:
DWELL TIME:
SAVE AND EXIT
EXIT W/O SAVE
EXIT W/O SAVE
Menu
Description
Options
Default
Mode
Disables/enables the hom- ON, OFF
ing function.
OFF
Function Type
Reverts to the defined
mode of operation.
Tour - Access a sequence of pre- Preset
set shots combined to provide a
pre-programmed tour of the area
covered by an AutoDome Easy
camera.
Auto Pan - Customizes auto pan
tours.
Preset - Pre-selects and stores a
combination of pan, tilt and zoom
positions which allow a set view
to be recalled. Also known as pre-
set shot.
Function Number
Dwell Time
Represents the tour, auto Tour - Allows a range of 1-4.
pan, or presets which have Auto Pan - Allows a range of 1-4.
1
been saved.
Preset - Allows a range of 1-60.
Indicates the period of time Allows a range of 5-600 sec.
the keyboard controller has
been in idle before activat-
ing the homing function.
Saves the data and exits the
menu.
5 sec.
Save and Exit
Exit W/O Save
Exits the menu without sav-
ing the data.
Bosch Security Systems, Inc.
Installation and Configuration Manual
December 06, 2006 | F01U032279
Download from Www.Somanuals.com. All Manuals Search And Download.
30 Dome Setup Menu
AutoDome Easy
17.2
Initialize Dome Menu
The Initialize Dome menu resets all menus to the factory default settings. Press the joystick to
the right to display the following message: ALL DATA WILL BE DELETED!! ARE YOU SURE?
DOME SETUP MENU
ALL DATA WILL BE DELETED!!
LANGUAGE: ENGLISH
OSD DISPLAY: OFF
AUTO PIVOT: ON
HOME FUNCTION
INITIALIZE DOME
DOME INFORMATION
SAVE AND EXIT
ARE YOU SURE?
NO
YES
EXIT W/O SAVE
17.3
Dome Information Menu
The Dome Information menu displays the firmware version.
DOME SETUP MENU
LANGUAGE: ENGLISH
OSD DISPLAY: OFF
AUTO PIVOT: ON
HOME FUNCTION
INITIALIZE DOME
DOME INFORMATION
SAVE AND EXIT
DOME INFORMATION
VERSION: 2.0.0
EXIT
EXIT W/O SAVE
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Easy
Keyboard Commands by Number
31
18
Keyboard Commands by Number
Function Comm Command
Description
Key
On/Off
On/Off
On/Off
Off
No.
1
2
8
Scan 360 degrees
Autopans from 0-360 degrees.
Autopan between defined limits.
Activate/deactivate.
Activates autopan 1
Play pre-position Tour 1
Alarm acknowledge
65
Acknowledge alarm or deactivate physi-
cal outputs.
On
66
Displays firmware version
Displays firmware version number.
Set ##–programs a preset view.
Shot ##–recall programmed preset.
Set–recalibrate home position.
Activates preset tour 1-4.
Set
“1-60” Pre-position programming
“1-60” Pre-position recall
Shot
Set
110
Factory P/T home position
Shot
“201- Run tour
204”
Shot
“301- Run auto pan
304”
Activates auto pan 1-4.
Bosch Security Systems, Inc.
Installation and Configuration Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
December 06, 2006 | F01U032279
32 Troubleshooting
AutoDome Easy
19
Troubleshooting
If you experience difficulties operating your AutoDome Easy camera, refer to the following. If
the guidelines do not enable you to solve the problem, contact an authorized technician.
Problem
Check
Nothing appears on the screen.
Are the power cord and line connection between
the camera and monitor made properly?
Is the lens dirty? If so, clean the lens with a soft,
clean cloth.
The image on the screen is dim.
The contrast on the screen is too weak. Adjust the contrast feature of the monitor. Is the
camera exposed to strong light? If so, change the
camera position.
The image on the screen is flickers.
Does the camera face directly into the sun or fluo-
rescent lighting? If so, reposition camera.
Is the power frequency set properly in sync? If the
power frequency is not set correctly, the line lock
synchronization mode cannot be used. Set the syn-
chronization mode to INT.NTSC Model power fre-
quency in LL mode: 60 Hz.
The image on the screen is distorted.
20
21
Preventive Maintenance
The following the preventive maintenance schedule allows detection and correction of minor
faults before they become serious and cause equipment failure. Periodically perform the fol-
lowing:
•
•
Inspect all connecting cables for deterioration or other damage.
Wipe housing with a clean damp cloth. Clean P.C (LEXAN) dome/windows with an
approved P.C (LEXAN) Cleaner (Novus LEXAN cleaner-plastic polish).
Verify that all the mounting hardware is secure.
•
Spare Parts List
Command
9965 300 00640
9965 300 00643
Description
Covert liner
Wire harness assembly
9965 300 00644 Black
9965 300 00645 White
Bubble assembly with screws
9965 300 00648
9965 300 00649
9965 300 00650
9965 300 00651
9965 300 00652
9965 300 00653
User manual
Accessory kit
Bubble tether
Screws for bubble tether
Mounting plate
Bubble screws torx lock
O-ring for bubble screws
December 06, 2006 | F01U032279
Installation and Configuration Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Americas:
Europe, Middle East, Asia:
Bosch Security Systems B.V.
Postbus 80002
Asia-Pacific:
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450
USA
Phone
Fax
5600 JB Eindhoven
Phone:
Fax:
+31 40 2577 200
+31 40 2577 202
+1 800 289 0096
+1 585 223 9180
Phone
Fax
+65 6319 3450
+65 63139 3499
© Bosch Security Systems, Inc., 2006; F01U032279 1.0 | 2006.12
Download from Www.Somanuals.com. All Manuals Search And Download.
|