RAID Subsystem DVA-08K
DVA-08K SCSI Premium Series
en Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Table of Contents | en
3
Warnings and Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Enclosure Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chassis Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hard Drive Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Rear Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Backplane Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Subsystem Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Drive Trays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
The RAID Controller Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Battery Backup Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power Supply Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cooling Fan Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Subsystem Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
I C Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Firmware and Bosch RAIDWatch GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Audible Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Hot-Swappable Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Hot-Swap Capabilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Normalized Airflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Precautions and Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Static-Free Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
BBU Warnings and Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
General Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Unpacking the Subsystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Rackmounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Considerations for Installation Site and Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Mounting Holes Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Drive Tray Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Subsystem Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Subsystem Monitoring Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Status-indicating LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Brief Overview of the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Drive Tray LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Controller Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Ethernet Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BBU Module LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PSU LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LCD Keypad Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cooling Fan Module LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Audible Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Default Threshold Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Failed Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3.2
4.4
2
I C Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
4
en | Table of Contents
RAID Subsystem DVA-08K | Installation Manual
Basic Configuration Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SCSI Connection Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Host Connection Topology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
LCD Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Subsystem Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Replacing Controller Module Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Selecting a Memory Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
DIMM Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Replacing a Faulty BBU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Notes on PSU Module Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Replacing the PSU Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Notes on Cooling Fan Module Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Replacing a Cooling Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Replacing a Failed Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Appendix: Spare Parts and Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Spare Parts Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Accessories and Optional Items. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Appendix: Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Null Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Main Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
10
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Warnings and Certifications | en
5
1
Warnings and Certifications
1.1
Warning
A shielded power cord is required in order to meet FCC emission limits and also to prevent
interference to nearby radio and television reception.
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that
changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
1.2
Safety Precautions
Precautions and Instructions
•
•
Prior to powering on the subsystem, ensure that the correct power range is being used.
The RAID subsystems come with drive bays. Leaving any of these drive bays empty will
seriously affect the efficiency of the airflow within the enclosure, and will consequently
lead to the system overheating, which can cause irreparable damage.
If a module fails, leave it in place until you have a replacement unit and you are ready to
replace it.
•
•
•
•
Airflow Consideration: The subsystem requires an airflow clearance, especially at the
front and the rear side.
Handle subsystem modules using the retention screws, extraction levers, and the metal
frames/faceplates. Avoid touching PCB boards and connector pins.
To comply with safety, emission, or thermal requirements, none of the covers or replace-
able modules should be removed. Make sure that during operation, all enclosure modules
and covers are securely in place.
•
•
•
Be sure that the rack cabinet into which the subsystem chassis will be installed provides
sufficient ventilation channels and airflow circulation around the subsystem.
Provide a soft, clean surface to place your subsystem on before working on it. Servicing
on a rough surface may damage the exterior of the chassis.
If it is necessary to transport the subsystem, repackage all disk drives separately. If using
the original package material, other replaceable modules can stay within the enclosure.
ESD Precautions
Observe all conventional anti-ESD methods while handling system modules. The use of a
grounded wrist strap and an anti-static work pad are recommended. Avoid dust or debris in
your work area.
1.3
Certification
FCC Class B Radio Frequency Interference Statement
FCC (applies in the U.S. and Canada)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules (47 CFR, Part 2, Part 15 and CISPR PUB. 22
Class B). These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
this user’s manual, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
6
en | Warnings and Certifications
RAID Subsystem DVA-08K | Installation Manual
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of FCC Rules. Operation is subjected to the following two
conditions: 1) this device may not cause harmful interference, and 2) this device must accept
any interference received, including interference that may cause undesired operation.
This device is in conformity with the EMC.
CB
(Certified Worldwide)
This device meets the requirements of the CB standard for electrical equipment with regard to
establishing a satisfactory level of safety for persons using the device and for the area sur-
rounding the apparatus. This standard covers only safety aspects of the above apparatus; it
does not cover other matters, such as style or performance.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Introduction | en
7
2
Introduction
This manual covers the DVA-08K series of RAID subsystems.
With its basic hardware redundancy and the capability of fast I/O transfer, the 2U RAID SATA
subsystem is an ideal solution to meet the ever increasing demands for addition of storage
capacity. Despite its ease of use, the subsystem does not compromise data protection for
convenience. The subsystem’s embedded firmware offers the same protection and mainte-
nance functionalities as those designed for an enterprise-level RAID solution. The subsystems
provide unprecedented configuration flexibility and allow for the customization of storage
subsystems to meet specific demands. It is a rigorous and durable subsystem that can be eas-
ily configured and operated.
Fully featured RAID redundancy (which provides advanced data protection) ensures that the
complete range of RAID levels (RAID 0, 1(0+1), 3, 5, 10, 30 and 50) is supported by the con-
troller head. A long list of sophisticated firmware functions (dedicated/global hot-spares, bat-
tery protected disk cache, configurable reaction schemes against drive errors, remote and
real-time array monitoring, and more) further guarantees the overall availability of valuable
data.
IT managers using the RAID subsystems will be able to rapidly develop a comprehensive stor-
age array. And the modular nature of the subsystem minimizes the maintenance effort to use
the RAID appliance.
2.1
Product Overview
The subsystem comes with two (2) SCSI-320 host channels interfaced through four (4) VHDCI
68-pin SCSI ports. The subsystem comes in a 2U-profile rack-mountable chassis which houses
a RAID controller module featuring complete RAID configuration and data protection function-
ality. The subsystem’s operation is protected by redundant, hot-swappable power supplies
and cooling fan modules. Designed for a high level availability, all major components are hot-
replaceable including its Li-ION battery and the RAID-protected disk drives.
The subsystem supports high-density array capacity by its eight drive bays for SATA-II inter-
face disk drives. The subsystem facilitates large I/O transfer, over its dual PCI-X buses archi-
tecture, and transmission of block I/Os over flexible caching and a dedicated XOR engine. The
subsystem is ideal for direct-attached data storage, backup, and retrieval. It combines the
capabilities and block-level performance of RAID storage with the reliable SCSI transfer tech-
nologies.
Configured arrays are easily combined with multiple ID/LUNs that appear to the host ports,
turning massive capacity into manageable units for data-sharing in a heterogeneous environ-
ment.
The RAID 2U-profile, SCSI-to-SATA RAID storage comes in two different models. The only dif-
ference between the two models is the number of SATA-II drive bays.
SCSI Host Ports
Connectivity: The subsystem features a 320MB/s bandwidth from each of its SCSI host chan-
nels. The dual-stack VHDCI connectors on the rear panel facilitate the connection to multiple
host computers and combining the storage capacities of multiple RAID subsystems. Its back-
ward compatibility with older SCSI protocols requires minimum investment for upgrading
equipment. Storage volumes are associated with SCSI ID/LUNs on the host channels. The
subsystem firmware provides flexible configurations of storage volumes which include, logical
drives in supported RAID 0, 1 (0+1), 3, and 5 levels, logical volumes that consist of one or
more logical drives, and the logical partitions of the previously mentioned configurations.
These volumes then appear as SCSI targets over the host links.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
8
en | Introduction
RAID Subsystem DVA-08K | Installation Manual
Channels: The SCSI ID/LUN mapping method enables users to associate a storage volume
with multiple IDs or LUNs on the host channels. The mapping method can easily cope with
host-side configurations such as clustered servers or high availability path redundancy. On the
drive side, all of the eight (8) SATA-II drives are connected each through a dedicated SATA
channel. Each drive channel is routed to an enclosure drive tray that is equipped with a stan-
dard SATA connector with of hot-swap capability. The methods used for assembling physical
drives, fault management, and status monitoring are identical to that used with Bosch’s long
line of RAID storage enclosures.
Active Components
The subsystem comes with:
•
•
•
•
•
A single RAID controller module
Two redundant, hot-swappable cooling modules
Dual redundant, hot-swappable, load-sharing power supplies
A module slot for a Li-ION battery module.
The front section of the enclosure houses eight (8) hot-swap drive bays for SATA-II or
backward compatible with SATA-I hard disk drives.
The subsystem is shown below:
Fig. 2.1 8-bay SATA RAID Subsystem
NOTICE!
On receiving and unpacking your subsystem, please check the package contents against the
included unpacking checklist. If any modules appear to be missing, please contact your sub-
system vendor immediately.
i
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Introduction | en
9
2.2
Enclosure Chassis
2.2.1
Chassis Overview
The RAID subsystem comes in a 2U metal chassis. A backplane board divides the enclosure
internally into front and rear sections. The front section accommodates eight (8) drive trays
(with their associated hard drives) and the rear section accommodates two (2) PSU modules,
two (2) single-fan cooling modules, and a single RAID controller module. The two (2) forearm
handles on the front of the subsystem enable you to easily insert/extract the chassis into/from
a rack or cabinet. Pre-drilled mounting holes on the sides of the chassis allow you to attach
separately purchased slide rails.
Fig. 2.2 Top View of the RAID subsystem
CAUTION!
When working with the subsystem, it is important to use tools with extreme care. Do not place
tools or other items on top of the enclosure to help avoid damaging the chassis finish.
2.2.2
2.2.3
Physical Dimensions
The subsystem comes in a standard 2U, 19” chassis with the following dimensions:
•
•
Measured with forearm handles: 482mm x 88mm x 505mm (width x height x depth)
Measured without forearm handles: 446mm x 88mm x 490mm (width x height x depth)
Front Panel Overview
The front section of the subsystem features a 4 x 2 layout for eight (8) 3.5-inch disk drives and
a foldable LCD keypad panel. The front panels of the RAID subsystems described in this man-
ual are shown in Figure 2.3. A description of the front panel component is given below:
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
10 en | Introduction
RAID Subsystem DVA-08K | Installation Manual
Fig. 2.3 Front View
The front panel is designed to accommodate the following components:
•
Forearm handles with an LCD keypad panel: The LCD Panel mounted on the left handle
shows system information and provides local access to the firmware-embedded configu-
ration and monitoring utility.
•
Drive bays with drive tray canisters: The drive bays are used to house the subsystem hard
drives. The DVA-08K contains 8 drive bays with a blank plate covering the lower part of
the front panel.
2.2.4
Hard Drive Numbering
The subsystem is housed in an enclosure that is 4 bays wide and 2 bays high. When viewed
from the front, drive bays (slots) are numbered 1 to 8, from the left to the right, and then from
the top to the bottom.
Fig. 2.4 Drive Bays Numbering Sequence
2.2.5
Rear Panel Overview
The rear section of the subsystems are accessed through the rear panel and is reserved for a
(PSUs), and two cooling fan modules.
The subsystem rear view is shown in Figure 2.5. A description of the rear panel component is
given in the proceeding discussions:
Fig. 2.5 Rear View
The rear panel shown above is designed to accommodate the following components:
•
RAID controller module: The controller module contains a controller main board and a
pre-installed DDR DIMM module.
•
Power Supply Unit (PSU): The PSU is used to provide power to the subsystem.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Introduction | en
11
•
•
BBU module: A BBU provides the protective implementation to cached data; and, unless
deselected when purchasing the subsystems, is installed into the module slot located at
the upper left corner of the controller module.
Cooling fan module: The redundant cooling fan module is used to ventilate the subsystem
and to reduce the temperature within the subsystem.
NOTICE!
Each of the power supplies on the sides of the enclosure houses one cooling fan module in a
removeable canister. When a power supply is removed, the cooling module is also removed.
Therefore, replace the power supply unit as soon as possible whenever it becomes necessary.
Cooling fan modules can be independently removed from the chassis without affecting PSU
operation.
i
2.2.6
Backplane Board
An integrated backplane board separates the front and rear sections of the subsystem. The
PCB board provides traces for logic level signal traces and low voltage power paths. It con-
tains no user-serviceable components.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
12 en | Introduction
RAID Subsystem DVA-08K | Installation Manual
2.3
Subsystem Components
All the active components on the subsystem can be accessed through either the front or rear
panel. The modular design of the active components facilitates their easy installation and
removal. Hot-swap mechanisms are incorporated to eliminate power surges and signal
glitches that might occur while removing or installing these modules.
2.3.1
LCD Panel
Fig. 2.6 Opening the Front Handle
The LCD panel shown in Figure 2.6 consists of a 16 characters x 2 rows LCD screen with push
buttons, a mute button, and LED status indicators. The LCD front panel provides full access to
all array configurations and monitoring. After powering up the subsystem, the initial screen
will show the subsystem model name. A different name can be manually assigned to the sub-
system or different drive arrays. This will enable easier identification in a topology consisting
of numerous arrays.
Fig. 2.7 Front Panel Retention Latch
To access drive bays in the left- or right-hand side column, first flip the retention latches (see
Figure 2.7) on the enclosure front handles, and then swing the handles to the left- and right-
hand sides. To close the handles (see Figure 2.8), swing the handles toward the system; gen-
tly press the handles until a click is heard. The latches will keep the handles in place.
Fig. 2.8 Closing the Front Handles
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Introduction | en
13
2.3.2
Drive Trays
The subsystem comes with 8 drive trays (see Figure 2.9) designed to accommodate separately
purchased standard 1-inch pitch, 3.5-inch disk drives. The drive bays are accessed from the
enclosure front. Two LED’s on the front of the tray are used to indicate the drive status. A key-
lock on each drive tray secures the hard drive in place, while an easily accessible release but-
ton ensures fast and efficient drive hot-swapping.
Fig. 2.9 Drive Tray Front View
CAUTION!
Be careful not to warp, twist, or contort the drive tray in any way (e.g., by dropping it or rest-
ing heavy objects on it). The drive tray has been customized to fit into the drive bays in the
subsystem. If the drive bay superstructure is deformed or altered, the drive trays may not fit
into the drive bay.
2.3.3
The RAID Controller Module
The RAID controller module contains a main circuit board, a preinstalled 256MB capacity or
above DDR RAM DIMM module, and the necessary support interfaces. The controller module
contains no user-serviceable components. Except when replacing a faulty unit or installing/
upgrading the cache memory inside, the controller module should never be removed or
opened.
CAUTION!
Although the RAID controller can be removed, the only time you should touch the controller
itself is to replace the memory module or to install the memory module. The RAID controller is
built of sensitive components and unnecessary tampering can damage the controller.
Controller Module Interfaces
The subsystems provide external interfaces to host computers and management station(s)
through the RAID controller’s rear-side faceplate as shown in Figure 2.10.
Fig. 2.10 Controller Module Faceplate
•
Host Ports
SCSI-320 Host Ports: Two SCSI-320 host channels connect the subsystem to the host
computers equipped with SCSI-320 compatible adapters through the dual-stack VHDCI
connectors. The dual-stack connectors facilitate cascade connections for configurations
such as host clustering or cascading with another RAID subsystem.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
14 en | Introduction
RAID Subsystem DVA-08K | Installation Manual
NOTICE!
This subsystems come with preset configurations for channel mode and channel ID settings,
and should be sufficient for most applications.
i
•
•
Ethernet Port
All controller modules on the subsystems come with a single 10/100BasedT RJ-45 Ether-
net port. The Ethernet port is used for local or remote management through the network
using the Bosch RAIDWatch GUI manager or Telnet protocol.
COM Port
All controller modules come with one RS-232C (audio jack) serial port. The serial port is
used for local access to the system-embedded configuration utility over the included
serial port cable.
DIMM Module
The controller module comes with a preinstalled 256MB capacity or above DDR RAM DIMM
module and can support a larger capacity up to 2GB. The DIMM module is mounted in an eas-
ily accessible location on the controller board. However, when the DIMM module is being
changed, the controller module must be removed from the subsystem chassis.
2.3.4
Battery Backup Unit
chassis. Please refer to Section 3 Hardware Installation for installation details.
Fig. 2.11 BBU Module
In accordance with international transportation regulations, the BBU module is only charged
to between 35% and 45% of its total capacity when shipped. Therefore, when powering on the
subsystem for the first time the BBU will begin to charge its batteries to their full capacity. It
normally requires approximately twelve (12) hours for the battery to be fully charged. If the
battery is not fully charged after twelve (12) hours (its LED is still flashing), there is a problem
with the BBU module and you should contact your subsystem vendor immediately. While the
battery is being charged, the LED on the BBU rear panel and the fifth LED on the controller
module will flash.
You can check the status of the battery’s charge via Bosch RAIDWatch Manager or the firm-
ware utility screen.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Introduction | en
15
2.3.5
Power Supply Units
The SATA-based RAID subsystems are equipped with two (2) redundant, hot-swappable, 2U,
350W power supply unit (PSUs) modules. The PSU is permanently mounted into a 2U high
(dual-level) bracket especially designed to house both the PSU and a cooling module mounted
underneath. PSUs can be found on either side of the controller module.
Each PSU comes with a single power socket for power cord plug-in and a single power switch
for you to turn the PSU on and off. Each PSU also comes with two embedded cooling fans to
provide sufficient airflow to keep the PSU cool. A single LED is used to indicate the PSU sta-
tus. A handle at the back of the PSU has been especially designed to enable you to remove the
PSU from the subsystem while the system is still online. This should only be done if the PSU
has failed and needs to be replaced.
NOTICE!
Hot-swapping the PSU also removes the cooling module at the lower slot.
A retention screw at the upper right corner of the PSU module is used to secure the PSU to
the enclosure. If the PSU needs to be removed, the retention screw must be removed first.
When installing a new PSU module, make sure that the retention screw has been firmly
secured.
i
Fig. 2.12 PSU Module
2.3.6
Cooling Fan Modules
The SATA-based RAID subsystem is equipped with two 1U single-fan, redundant, hot-swappa-
ble cooling modules shown in Figure 2.13. One 9.7cm fan is housed in each cooling module.
These modules have been designed to generate a cooling flow from the front to the rear of the
subsystem to extract the heat generated by the SATA hard drives. Two of the cooling fan mod-
ules are installed directly beneath the PSUs.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
16 en | Introduction
RAID Subsystem DVA-08K | Installation Manual
Fig. 2.13 Top View of a Cooling Fan Module
Advanced Fault-Preventative Operation
The cooling fan modules support dual-speed operation modes that help to protect the subsys-
tem in the event of component failure or extreme working condition.
Intelligent Dual Speed Operation
The cooling fans operate with two rotation speeds. Under normal operating conditions, the
cooling fans run at the low speed, which is sufficient for maintaining efficient airflow across
components. Under the following conditions, cooling fans raise their rotation speed to
increase the airflow:
1. Component Failure: if another cooling fan module, a PSU, or a temperature sensor fails,
the remaining cooling fan(s) automatically raises its rotation speed.
2. Elevated Temperature: if the temperature breaches the upper threshold set for any of the
interior temperature sensors, the cooling fans automatically raises its rotation speed.
3. During the subsystem initialization stage, the cooling fans operate at the high speed and
return to lower speed once the initialization process is completed and no erroneous con-
dition is detected.
NOTICE!
There are two values set for the upper temperature thresholds. One is set for event notifica-
tion and the other triggering higher fan rotation speed. The preset value for event notification
can be changed using the firmware-embedded configuration utility, while the fan speed trig-
ger is not a user’s option.
i
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Introduction | en
17
2.4
Subsystem Monitoring
The SATA-based RAID subsystem comes with a number of different monitoring methods that
provide you with continual updates on the status of the system and individual components.
The following monitoring features are included in the subsystem.
2.4.1
I2C Bus
The following subsystem elements are interfaced to the RAID controller over a non-user-ser-
viceable I2C bus:
•
•
•
Cooling fan modules
PSUs
Temperature sensors
2.4.2
LED Indicators
The following active components come with LEDs to indicate the status of the individual com-
ponents:
•
•
•
•
•
•
RAID controller
LCD panel
Cooling fan module
PSU module
BBU module
Drive trays
2.4.3
2.4.4
Firmware and Bosch RAIDWatch GUI
Firmware: The firmware is pre-installed software that is used to configure the subsystem. The
firmware can be accessed either through the LCD keypad panel or a terminal emulation pro-
gram running on a management computer that is connected to the subsystem’s serial port.
Bosch RAIDWatch: Bosch RAIDWatch is a premier Web-based graphical user interface (GUI)
that can be installed on a remote computer and is used to access the array through LAN or the
Internet. The manager communicates with the array via the connection of the existing host
interface or Ethernet link to the RJ-45 LAN port.
Audible Alarms
The subsystems come with audible alarms that are triggered when certain active components
fail or when certain (controller or subsystem) thresholds are exceeded. If you hear hastily
repeated beep tones from the subsystems it is imperative that you immediately determine and
rectify the problem.
Event notification messages indicate the completion of or the condition when proceeding with
array configuration tasks and are always accompanied by two or three successive and pro-
longed beeps.
CAUTION!
Failing to respond when a critical alarm is heard can lead to permanent damage of the subsys-
tem. When an audible alarm is heard, rectify the problem as soon as possible.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
18 en | Introduction
RAID Subsystem DVA-08K | Installation Manual
2.5
Hot-Swappable Components
2.5.1
Hot-Swap Capabilities
The subsystem comes with a number of hot-swappable components. A hot-swap component
is one that can be exchanged while the subsystem is still online without affecting the opera-
tional integrity of the subsystem. These components should only be removed from the subsys-
tem when they are being replaced. At no other time should these components be removed
from the subsystem.
2.5.2
2.5.3
Components
The following components are all hot-swappable:
•
•
•
•
Power supply units (PSUs)
Cooling fan modules
Hard drives
BBU module
Normalized Airflow
Proper subsystem cooling is referred to as “normalized” airflow. Normalized airflow ensures
the sufficient cooling of the subsystem and is only attained when all components are properly
installed. Therefore, a failed component should only be hot-swapped when a replacement is
available. If a failed component is removed but not replaced, permanent damage to the sub-
system can result.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Hardware Installation | en
19
3
Hardware Installation
This chapter gives detailed instructions on how to install the subsystem. When installing the
subsystem, it is necessary to mount the chassis into a rack or cabinet and to install hard
drives and drive trays. Installation into a rack or cabinet should occur before the hard drives or
drive trays are installed into the subsystem. Please confirm that you received all of the compo-
nents listed on the Unpacking List that came with the subsystem before proceeding with the
installation process.
CAUTION!
Please note that the installation instructions described in this chapter should be carefully fol-
lowed to prevent any difficulties and damages to your system.
3.1
Installation Prerequisites
Static free installation environment: The subsystems must be installed in a static-free
environment to minimize the possibility of electrostatic discharge (ESD) damage. (See
Section 1 Warnings and Certifications).
•
Component check: Before installing the subsystems, you should first check to see that
you have received all the required components. If any items appear damaged, contact
your vendor for a replacement.
•
•
Hard drives: Hard drives must be purchased separately prior to the subsystem installa-
tion.
Cabling:
–
The subsystems requires an external VHDCI-to-VHDCI SCSI round cable to connect
the subsystem to a host computer.
–
One (1) audio-jack-to-DB9 cable is provided to facilitate the connection of the COM1
port for local terminal emulation access to the array.
–
–
Two (2) power cords are provided for the power connections to the power sources.
The RJ-45 Ethernet cable for network management connection is a user-supplied
item.
•
•
Memory module: If you wish to change the pre-installed memory module, a separately
purchased module must be installed. Please contact your vendor for a different memory
module or consult the list of compatible modules.
Rack installation: The enclosure chassis can be installed into a rack cabinet using self-
purchased mounting rails. A printed copy of installation guide is provided with the slide
rails package.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
20 en | Hardware Installation
RAID Subsystem DVA-08K | Installation Manual
3.2
Safety Precautions
3.2.1
Precautions and Instructions
•
Be sure the correct power range (100-120 or 220-240VAC) is supplied by your rack cabi-
net, UPS device, or power outlet.
•
Thermal notice: All drive trays (even if they do not contain a hard drive) must be installed
into the enclosure. Leaving a drive bay or module slot open will severely affect the airflow
efficiency within the enclosure, and will consequently lead to system overheating. Keep a
faulty module in place until you have a replacement unit and you are ready to replace it.
An enclosure without disk drives can weigh over 25 kilograms. Two (2) people are
required to install or relocate the subsystem. To avoid damage to disk drives, drives
should be removed from the enclosure before moving the subsystem.
Handle the system modules by the retention screws, extraction levers, or the modules
metal frames/faceplates only. Avoid touching the PCB boards, connector pins, and sol-
dered surfaces.
•
•
•
Airflow considerations: The subsystem requires an airflow clearance especially on the
front and rear. For proper ventilation, a minimum of 2.5cm is required between the front
of the enclosure and rack cover; a minimum of 5cm is required between the enclosure
and end of the rack.
•
•
•
•
•
•
None of the covers or replaceable modules should be removed in order to maintain com-
pliance with safety, emission, or thermal requirements.
Always secure every enclosure module by its retaining screws or make sure it is held in
place by its latches.
Always make sure the subsystem has a safe electrical earth connection via power cords
or chassis ground by the rack cabinet.
Be sure that the rack cabinet in which the subsystem chassis is to be installed provides
sufficient ventilation channels and airflow circulation around the subsystem.
Provide a soft, clean surface to place your enclosure on before working on it. Servicing
the enclosure on a rough surface may damage the finish of the chassis.
If it is necessary to transport the subsystem, repackage all disk drives separately. If using
the original package material, all other modules can stay within the enclosure.
3.2.2
Static-Free Installation
The subsystem contains static-sensitive electronic components that can be damaged by
improper handling and electrostatic discharge (ESD). To prevent ESD damage to any of the
components, follow these precautions before touching or handling them:
•
Discharge the static electricity from your body by wearing an anti-static wristband or by
touching a grounded metal surface.
•
•
Avoid carpets, plastic, vinyl, and styrofoam in your work area.
Handle all components by holding their edges or metal frame. Avoid touching PCB boards
and connector pins.
3.2.3
BBU Warnings and Precautions
The BBU module sustains cache memory in the event of a power failure or in the unlikely event
if both PSUs have failed. Having the protection to cached data by a BBU is highly recom-
mended. The BBU provides additional data security and helps minimize the chance of data
loss during power outage.
•
Replace the BBU once it shows symptoms failing to hold the charge. Although the life
expectancy of a BBU is determined by the times it has been charged or discharged, a BBU
can approximately last for one year. If the battery recharge time is obviously longer than
the suggested 12 hours, or if the fault LED is lit, replace the battery.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Hardware Installation | en
21
•
•
•
Install or replace the BBU module only with a BBU module supplied by your subsystem
vendor. Use of battery cells provided by another source will void our warranty.
Always dispose of discharged or used batteries in an ecologically responsible manner.
Dispose used BBUs at authorized battery disposal sites only.
Do not use nor leave the BBU near a heat source or direct sunlight. Heat can melt the
insulation and damage other safety features of battery cells, possibly leading it to acid
leak and result in flames or explosion.
•
Do not immerse the BBU in water nor allow it to get wet. Its protective features can be
damaged. Abnormal chemical reactions may occur, possibly causing functional defects,
acid leak, and other hazardous results.
•
•
Do not disassemble or modify the BBU. If disassembled, the BBU could leak acid, over-
heat, emit smoke, burst and/or ignite.
Do not pierce the BBU with a sharp object, strike it with a hammer, step on it, or throw it.
These actions could damage or deform it, internal short-circuiting can occur, possibly
causing functional defects, acid leaks, and other hazardous results.
If the BBU leaks, gives off a bad odor, generates heat, becomes discolored or deformed,
or in any way appears abnormal during use, recharging or storage, immediately remove it
from the subsystem and stop using it. If this is discovered when you first use the BBU,
return it to Bosch or your system vendor.
•
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
22 en | Hardware Installation
RAID Subsystem DVA-08K | Installation Manual
3.3
General Installation Procedure
The following instructions can save installation time. Detailed, illustrated instructions for each
component are given in the following sections.
CAUTION!
To ensure that your system is correctly installed, please follow the steps outlined below. If you
follow these steps, installation will be fast and efficient. If you do not follow these steps, you
may have incorrectly installed the hardware.
1. Unpack: Unpack the subsystem and confirm that all the components on the Unpacking
Checklist have been included.
2. Rack/Cabinet installation: If the subsystem is going to be installed in a rack or cabinet, it
should be installed prior to installing the hard drives. Installing the subsystem into a rack
or cabinet requires at least two (2) people.
trays must be installed into the enclosure itself. (See Section 3.6 Drive Tray Installation)
4. Cable connection: Use the power cords that came with the subsystem to connect the
subsystem to the main power source. Use self-purchased SCSI cable to connect host
ports to servers.
connected, you can power up the subsystem and configure the RAID array. (See
Section 5.4 Power On)
3.3.1
Installation Procedure Flowchart
Table 3.1 shows a flowchart of the installation procedure. As you complete each step, check
off the “Done” box on the right. Please use this flowchart in conjunction with the instructions
that follow.
Step
Installation Procedure
Done
1
Unpack
3
5
6
7
Rack/Cabinet Installation
Drive Tray Installation
Cable Connection
Power On
See Section 3.6 Drive Tray Installation
See Section 5.4 Power On
Table 3.1 Installation Procedure Flowchart
3.4
Unpacking the Subsystem
Use the unpacking checklist in your package to check packing contents. Carefully check the
items contained in each box before proceeding with installation.
NOTICE!
A detailed packing list can be found in your product shipping package or product CD.
i
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Hardware Installation | en
23
3.5
Rackmounting
The subsystem is easily installed into a standard 19-inch rack cabinet using the mounting
holes on the sides of chassis.
The enclosure chassis can be installed using self-purchased mounting rails.
3.5.1
Considerations for Installation Site and Chassis
•
Make sure you have an appropriate site location and cables prepared with adequate
lengths to connect to main power and other devices.
•
At least two people will be required to install the chassis. Disk drives should only be
installed after the chassis is properly mounted. The chassis can weigh about 24Kgs with-
out disk drives.
•
The following tools are necessary for mounting the chassis:
–
–
#4 Phillips-head screwdriver
Wrenches may be necessary, depending on the rack type
•
•
Use the included M5 or M6 screws for securing the chassis through its front mounting
ears.
More details about the use of optional slide rails are given in the Installation Guide that
came with the slide rail package.
3.5.2
Mounting Holes Positions
•
Integrators may design their own brackets or slide rails using the twenty-two (22) mount-
ing holes on the sides of chassis.
•
There are six (6) mounting holes with six (6) M4 nuts near the end of the chassis on each
side. Shown below are the locations of these mounting holes. (See the arrow marks in
Figure 3.2). See the next diagram for another group of mounting holes on a horizontal
line.
Fig. 3.1 Enclosure Side Mounting Holes (1)
•
Figure 3.2 shows holes that are designed for slide rail options. There are five (5) mount-
ing holes for #6-32 screws on the sides of the enclosure for use with slide rails purchased
separately from Bosch or other vendors.
•
For information on installing the chassis using the slide rails, please refer to the Installa-
tion Manual that came with the kit.
Fig. 3.2 Enclosure Side Mounting Holes (2)
•
Use M5 or M6 pan-head screws to secure the chassis to the front cabinet posts.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
24 en | Hardware Installation
RAID Subsystem DVA-08K | Installation Manual
3.6
Drive Tray Installation
Once the hard drives have been installed in the drive trays, the drive trays can be installed into
the subsystem.
WARNING!
All drive trays must be installed into the enclosure even if they do not contain a hard drive. If
the trays are not installed into the enclosure, the ventilation required for cooling will be dis-
turbed and the subsystem will overheat.
1. Make sure that the hard drive is secured to the drive tray. Make sure the key-lock is in the
unlocked position. The key-lock is unlocked if the groove on its face is in a horizontal ori-
entation. If the groove is in a vertical position, as shown in Figure 3.3, then the key-lock is
locked and the front flap on the drive tray cannot be opened.
Fig. 3.3 Front View of an Individual Drive Tray
2. Open the front flap on the drive tray. (See Figure 3.4). To open the flap, push the release
button on the front bezel. The front flap will open in an upward direction.
Fig. 3.4 Opening Drive Tray Front Flap
3. Align the drive tray with the slot in which you wish to insert it. Make sure that it is resting
on the rails inside the module slot. Once the drive tray is lined up with the slot, gently
slide it in. This should be done smoothly and gently.
4. Close the front flap on the drive tray. Make sure the front flap is closed properly. Closing
the front flap ensures that the drive tray is firmly connected to the corresponding connec-
tor on the backplane board. If the front flap is not closed properly, the connection
between the HDD and the subsystem will not be secure. DO NOT slam the drive tray into
place! The connector pins might be damaged. If the front flap is not closed properly, the
connection between the hard drive and the subsystem will not be secure.
5. Lock the flap into place by turning the key-lock until the groove on its face is pointing
down (vertical orientation). (See Figure 3.5)
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Hardware Installation | en
25
Fig. 3.5 Drive Tray Key-lock Rotation
6. Once all drive trays are installed, the RAID subsystem will poll the drive channels and rec-
ognize the drives and scan them in automatically.
7. When powered up, you should check the LEDs on drive bezels to ensure all drives are
receiving power and are functional. All drive LEDs should be solid green after the initial-
ization stage.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
26 en | Subsystem Monitoring
RAID Subsystem DVA-08K | Installation Manual
4
Subsystem Monitoring
This chapter provides information on how to monitor the subsystem.
4.1
Subsystem Monitoring Overview
The subsystem is equipped with a variety of self-monitoring features that help to keep subsys-
tem managers informed of the subsystem operational status. These monitoring features pro-
vide vital feedback to help you maintain the operational integrity of the subsystem. Prompt
response to warnings and subsystem component failure notifications will ensure safe opera-
tion of the subsystem and help ensure the longevity of the subsystems.
Self-monitoring features include:
•
Firmware (FW): The RAID controllers in the subsystems come with pre-installed FW. The
FW can be accessed using either the LCD keypad panel or a PC running terminal software
through the RS-232C (audio jack) serial port. Device status information can be obtained
from the FW.
•
Bosch RAIDWatch: Bosch RAIDWatch is a fully integrated Java based Graphical User
Interface (GUI) that came with the subsystem and can be used to monitor and maintain
the subsystem using web browsers. Connection to a Bosch RAIDWatch station is made
using the existing Ethernet ports.
•
•
The Bosch RAIDWatch Panel View can be customized to show a direct, graphical repre-
sentation of the subsystem in the content panel of the Bosch RAIDWatch screen. Panel
View allows you to quickly determine the operational status of critical components.
Configuration Client: The powerful Configuration Client sub-module can be used to keep
you informed of system events via a variety of communication methods like email, LAN
broadcast, fax, pager, MSN messenger, ICQ, and SMS. The sub-module runs as an inde-
pendent program from Bosch RAIDWatch main program. The Configuration Client helps
prevent blind time and keeps you constantly informed as to the status of the storage
management subsystem.
•
•
LEDs: Device-status-indicating LEDs are placed on all of the subsystems’ active compo-
functions. (See Figure 4.2)
Audible Alarm: An audible alarm is present on the subsystem controller board and will be
triggered if any of a number of threatening events occurred. These events usually jeopar-
dize the functional and operational integrity of the controller board and must be heeded
at all times. Events such as a breaching of the temperature threshold will trigger the
appropriate corrective measures. (See Figure 4.3)
2
2
•
Inter-Integrated Circuit (I C): The I C bus monitors the operational integrity of the cool-
ing modules, sensors for RAID controller board/backplane temperature and voltage read-
ings.
Subsystem monitoring is a necessary part of subsystem management. If failure events or other
disruptive events are detected and reported, the subsystem managers must take the appropri-
ate action to rectify the problem. Failure to act in a properly specified manner to a system
event (like overheating) can cause severe and permanent damage to the subsystem.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Monitoring | en
27
4.2
Status-indicating LEDs
4.2.1
Brief Overview of the LEDs
The following devices come with LEDs that inform subsystem managers about the operational
status of the component on which they are mounted. The RAID subsystem features status-
indicating LEDs distributed over the active components in the following ways:
Component
Drive Trays
LED(s) per Unit
Total LEDs
2
16
LEDs
Controller Module
Ethernet Ports
BBU Module
5
2
1
5
2
1
Port LEDs
See Section 4.2.5 BBU Module
LED
PSU Module
1
3
2
3
LCD Keypad Panel
Panel
Cooling Fan Module
1
2
Module LED
Table 4.1 LED Distribution
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
28 en | Subsystem Monitoring
RAID Subsystem DVA-08K | Installation Manual
4.2.2
Drive Tray LEDs
Two LED indicators are located on the right side of each drive tray. (See Figure 4.1) Refer to
Table 4.2 for LED definitions. When notified by a drive failure message, you should check the
drive tray indicators to find the correct location of the failed drive. Replacing the wrong drive
can cause fatal failure of a logical array.
Fig. 4.1 Drive Tray LEDs
LED Name
Drive Busy
Color
Status
Blue
ON indicates read/write activity on the drive.
OFF indicates there is no read/write activity on the drive.
Power Status
Red/
GREEN indicates that power is being supplied to the drive.
OFF indicates no power is being supplied to the drive or the
drive tray is not properly installed. .
Green
RED indicates drive failure or faults have occurred.
Table 4.2 Drive Tray LED Definitions
4.2.3
Controller Module LEDs
The rear-facing faceplate of the RAID controller module is shown in Figure 4.2. The rear-facing
faceplates on the two models look identical. The LEDs are numbered from 1 to 5. There are
two more LEDs on the Ethernet port. The definitions are shown in Table 4.3 below.
Fig. 4.2 Controller Faceplate
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Monitoring | en
29
LED
Name
Color
Green
Status
1
Controller Ready
ON: Indicates controller is active and
operating normally.
FLASHING: Indicates controller initial-
ization is taking place.
OFF: Controller is not ready for opera-
tion.
2
3
4
Hst_Bsy
Green
Green
Amber
FLASHING: Activities on the host ports.
OFF: No activities on the host ports.
(Host Ports Busy)
Drv_Bsy
FLASHING: Activities on the drive side.
OFF: No activities on the drive side.
(Drive Busy)
C_Dirty
ON: Indicates that data is currently
being cached in memory or is being
held up by the BBU during a system
power loss.
(Cache Dirty)
5
BBU_Fail
Amber
ON: Indicates the BBU has failed and
cannot sustain cached data.
OFF: Indicates the BBU can sustain
cached data in memory.
FLASHING: The BBU is charging.
Table 4.3 Controller Module LED Definitions
4.2.4
Ethernet Port LEDs
The subsystem comes with a RS-232C audio jack serial port that can be used to assign a per-
manent IP to the subsystems. After a permanent IP address has been assigned, an Ethernet
cable can be used to connect the RJ-45 Ethernet port to a network hub or router. This enables
you to manage your subsystem locally or remotely over TCP/IP. See Figure 4.3 for the loca-
tions of the two LED indicators on Ethernet port. Refer to Table 4.4 for the LED definitions.
Fig. 4.3 Ethernet Port Indicators
Name
Link Status
LAN Activity
Color
Green
Green
Color
ON: Indicates a valid connection to network
BLINKING: Indicates active transmissions
Table 4.4 Ethernet Port LED Definitions
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
30 en | Subsystem Monitoring
RAID Subsystem DVA-08K | Installation Manual
4.2.5
BBU Module LED
The BBU module has an LED on its faceplate. (See Figure 4.4) The function is the same as the
fifth LED on the controller module. The LED is off when the BBU is functioning normally and is
able to sustain the cache memory. The LED flashes to indicate the BBU is currently charging
its battery cells. If the LED is illuminating amber, the unit may have failed. Please contact your
system vendor to verify the problem.
Fig. 4.4 BBU Module LED
4.2.6
PSU LED
Fig. 4.5 PSU LED
Each PSU comes with a single LED located just above the power switch and just below the
retention screw (see Figure 4.5). The LED is used to indicate the operational status of the PSU
module. Please refer to the PSU LED definitions shown in Table 4.5.
Color
Status
Flashing Green
The power supply has not been turned on. The PSU module LED will
blink when the subsystem is connected to a power source but has not
been turned on.
Static Green
Static Red
The PSU is operating normally and experiencing no problems
The PSU has failed and is unable to continue providing power to the
subsystem.
OFF
The power cord is unplugged or the power cord is plugged but no
power is being supplied from the power source.
Table 4.5 PSU Module LED Definitions
4.2.7
LCD Keypad Panel
The LCD panel located on the front aluminum foldable handle comes with three status LEDs.
The LEDs are marked from top to bottom “PWR,” “BUSY” and “ATTEN” and are clearly seen in
Figure 4.6 below. The definitions of these LEDs are shown in Table 4.6. The mute button can
be used to stop the alarm until the next controller event occurs.
Fig. 4.6 LCD Keypad Panel
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Monitoring | en
31
Name
Color
Status
POWER
Blue
ON indicates that power is being supplied to the subsys-
tem.
OFF indicates that no power is being supplied to the sub-
system.
BUSY
White
Red
Flashing indicates that there is activity on the host/drive
channels.
OFF indicates that there is no activity on the host/drive
channels.
ATTENTION
ON indicates that one or more component failure/critical
events have occurred.
OFF indicates that the subsystem and all its components
are operating normally.
Table 4.6 LCD Panel LED Definitions
NOTICE!
The LCD panel ATTEN LED will be turned on during the power up process. The ATTEN LED will
be turned off after the boot up procedure is completed correctly.
i
4.2.8
Cooling Fan Module LED
The cooling fan module comes with a single status-indicating red LED shown in Figure 4.7.
LED definitions are given in Figure 4.7.
Fig. 4.7 Cooling Fan Module LED
RED
Status
OFF
ON
The cooling fan module is operating normally.
The cooling fan module has failed and must be replaced.
Table 4.7 Cooling Fan Module LED Definitions
The subsystem has a novel approach to stabilizing the temperature within the subsystem:
When the sensors within the enclosure detect critical working conditions, such as high ambi-
ent temperature or the failure of any cooling or PSU module, the system will turn the cooling
fans to high speed to extract more heat. Once the ambient temperature cools down to normal
or the faulty module has been replaced, the cooling fans return to normal speed.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
32 en | Subsystem Monitoring
RAID Subsystem DVA-08K | Installation Manual
4.3
Audible Alarm
Different subsystem environmental and operational parameters (i.e., temperature, etc.) have
been assigned a range of values between which they can fluctuate. If either the upper or lower
thresholds are exceeded, an audible alarm will automatically be triggered. The alarm will also
be triggered when an active component of the subsystem fails. If the subsystem manager is
onsite and hears the alarm, the manager will have to read the error message on the LCD
screen or the PC terminal in order to determine what has triggered the alarm. After determin-
ing what has occurred, the subsystem manager must take appropriate actions to rectify the
problem.
CAUTION!
When an alarm is triggered, it is necessary for you to determine the problem. If the audible
alarm is ignored and the problem is not rectified, unexpected damages may occur.
4.3.1
Default Threshold Values
NOTICE!
The threshold values listed below are used to trigger a warning event and sound the alarm. A
different value set is reserved for triggering the cooling fans to operate at a high rotation
speed. The fan speed value set is not user-configurable.
i
Table 4.8 shows the default threshold values for the subsystem. If any of these values are sur-
passed, the alarm will sound.
Upper Threshold
+3.6V
Lower Threshold
+2.9V
+3.3V
+5V
+5.5V
+13.2V
90ºC
80ºC
40ºC
+4.5V
+10.8V
5ºC
+12V
CPU Temperature
Board Temperature
5ºC
Enclosure Ambient
Temperature
0ºC
Table 4.8 Default Threshold Values
The controller self-monitoring thresholds in Table 4.8 are the default threshold values. The val-
ues set for the subsystem’s ambient temperature are pre-configured before shipping and can-
not be changed.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Monitoring | en
33
4.3.2
Failed Devices
The audible alarm will be triggered if any of the following devices fail:
•
•
•
•
•
Cooling fan modules
PSU modules
BBU modules
Hard drives
Components on the RAID controller
NOTICE!
If the temperature exceeds a preset threshold, the BBU charger circuits will stop charging.
i
You will then receive a message that says “Thermal Shutdown/Enter Sleep Mode.” When the
temperature falls back within normal range, the battery will resume charging.
2
4.4
I C Monitoring
Module presence detection and the general working status of cooling fan and other modules
2
are monitored through an I C serial bus. If any of these modules fails, the failure will be
detected and you will be notified via the various methods described above.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
34 en | Subsystem Connection and Operation
RAID Subsystem DVA-08K | Installation Manual
5
Subsystem Connection and Operation
This chapter introduces sample topologies, configuration options and server connections for
the RAID subsystems and discusses both the power on and power off procedures.
5.1
Basic Configuration Rules
When you are configuring your storage subsystem, follow these basic rules:
•
Using a mix of LVD and legacy devices, such as devices using single-ended signaling, is
not recommended. Use LVD terminators if all your devices support LVD signaling. Please
refer to the documentation provided with your SCSI devices to avoid possible conflicts.
When selecting the number of hard drives to be included in a logical configuration that
should be presented through the host channels, the transfer rates and the mechanical
performance of the hard disks should be considered. The combined bandwidth of the
two SCSI host channels is 640MB/s, sufficient for most applications. If properly config-
ured, combining subsystems or drive enclosures may increase the number of drives and
help to bring out the most of IOPs performance.
•
•
•
If you consider cascading multiple enclosures, considerations may include the character-
istics of your I/O load. Select the correct combination of optimization mode and a spe-
cific RAID level.
An optimal configuration is always a compromise among different factors. For instance, a
large array with many drive members may be more efficient, but the chance of failing a
member is also increased.
•
•
The drives in the same logical array should have the same capacity; it is preferred that all
the drives in the enclosure have the same capacity.
A spare drive should have a minimum capacity equivalent to the largest drive that is to be
replaced. If the capacity of the spare is less than the capacity of the drive to be replaced,
then the controller will not proceed with the failed drive rebuild.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Connection and Operation | en
35
5.2
SCSI Connection Overview
The SCSI host ports connect to SCSI-320 host adapters (HBA) that comply with 320MB/s
transfer rate and SCSI-3 protocol, best capable of 64-bit/133MHz PCI operation. Connection
of the subsystem’s SCSI ports is flexible. For example, you may use the two VHDCI ports of a
dual-stacked connector to connect a host channel to two separate, clustered servers. If high
availability or path redundancy software is applied, a total of 4 VHDCI ports are available for
cross-linking to host adapters. As long as access contention is not of the concern, host con-
nection can be very flexible. In the following sections, configuration diagrams will be provided
to illustrate the possible uses of the subsystem in different application environments.
Note that these configurations are only recommendations and do not intend to impose limita-
tions such as the use of high availability software or cascading multiple enclosures. The same
configuration principles applies to the subsystem.
The RAID subsystems support 2 SCSI host channels and 2 dual-stack connectors featuring
support for SCSI-320 protocol (also known as Ultra-320), the latest iteration of the SCSI drive
interface standard. The SCSI-320 enables maximum data transfer rates up to 320MB/second
per channel from host computers to the subsystems or expansion systems. This is twice the
bandwidth as the Ultra160 standard, allowing you optimal performance and flexibility with
configuring storage applications.
5.2.1
5.2.2
SCSI Cables
One SCSI cable is required with each subsystem for host connection. If you wish to connect
the second host channel, a second cable is required. Use only high quality SCSI-320 cables
from a reputable manufacturer. To ensure optimum performance, it is necessary to use
proper, high quality SCSI-320 compatible cables. Failure to do so will result in downgraded
performance.
SCSI Port on the Controller Rear Panel
•
The SATA-based subsystem is equipped with two dual-stacked connectors on the back of
the enclosure. Each dual-stacked connector comes with two 68-pin VHDCI ports that is
specified as a “Channel # In” or “Channel # Out” port.
The SCSI ports are specified as “In” or “Out” for ease of identification. As long as each
device on a SCSI bus is assigned with a unique ID and the SCSI bus properly terminated,
there are no limitations with connecting a specific SCSI port to the host- or drive-side
devices.
Fig. 5.1 Dual-stacked Connectors on the Controller Faceplate
•
•
The subsystem requires an external VHDCI-to-VHDCI SCSI round cable to connect the
subsystem to a host adapter.
One (1) audio-jack-to-DB9 cable is provided to facilitate the connection of the COM1 port
for local terminal emulation access to the array.
•
•
Two (2) power cords are provided for the power connections to the power sources.
The RJ-45 Ethernet cable for network management connection is a user-supplied item.
Use straight-through Ethernet cables with RJ-45 plugs.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
36 en | Subsystem Connection and Operation
RAID Subsystem DVA-08K | Installation Manual
5.2.3
SCSI Termination
Correct SCSI termination procedures require that the last device on the SCSI bus be termi-
nated. If the last device is not terminated or if devices other than the last are terminated,
erratic SCSI bus behavior may occur.
An auto-detection, on-board terminator is built into the DVA-08K. You do not need to install an
external terminator when a subsystem acts as the last device in the daisy chain configuration.
The on-board terminator default is enabled. If the subsystem is not the last device in the daisy
chain configuration, the terminator will be automatically disabled. Although it is not recom-
mended, if you prefer to disable the firmware setting for the on-board terminator using the
LCD keypad panel on the subsystem, RS232C terminal session, or Bosch RAIDWatch manage-
ment software, the auto-detection function is also disabled.
Typically, the host computer or host adapter (SCSI card inside the PC) is the first device and
some are already terminated. When installing the DVA-08K on a SCSI bus with other devices,
be sure to observe the above rules regarding all devices on the SCSI bus. Consult your host
computer and/or host adapter manual for additional information on correct termination pro-
cedures.
NOTICE!
It is recommended not to change the firmware default setting for the SCSI terminator so the
auto-detection function can operate.
i
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Connection and Operation | en
37
5.3
Host Connection Topology
Fig. 5.2 Cascaded Subsystems Connected to Two Host Computers
In the example shown in Figure 5.2, the SCSI ports are connected to different host computers.
This provides both path and host computer redundancy. If one of the host channels becomes
disconnected, or if the cable connecting one of the host ports to the host computer is dam-
aged, the second path can transmit data from the subsystem to one of the host computers.
Similarly, in the clustered hosts configuration, the same array can be accessed through differ-
ent data paths and downtime will be minimized.
To obtain more disk capacity, the “Out” ports are used to cascade another subsystem.
The host-side connection can be made as the following:
1. Directly to servers or workstations equipped with SCSI HBAs.
2. Connect two subsystems on the same host buses for a larger combined capacity.
3. Cross-link the host ports on subsystem(s) to clustered servers.
High availability configurations, such as clustering or redundant paths settings, can be applied
with adequate software control. The same logical array can be associated with two or more
different host IDs to facilitate access down through different HBAs.
Default Channel Settings
Model
DVA-08K
Host Channels
Drive Channels
Channel 0 and Channel 1
Channels 1 to 8, each dedicated to
one connected drive
Table 5.1 Default Channel Settings
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
38 en | Subsystem Connection and Operation
RAID Subsystem DVA-08K | Installation Manual
5.4
Power On
After installing all the components in the subsystem, connecting the host channels to the
host, and connecting the expansion cables to the expansion enclosures, the subsystem is
ready to be powered on.
5.4.1
Power On Checklist
BEFORE powering on the subsystem, please check the following:
•
•
•
•
Memory module: Memory module has been correctly installed on the controller board.
BBU modules: Ensure that the BBU modules have been installed correctly.
Hard drives: Hard drives have been correctly installed on the drive trays.
Drive trays: ALL the drive trays, whether or not they have a hard drive, have been installed
into the subsystem.
•
•
•
Cable connections: The host ports on the subsystem have been correctly connected to
host computer(s).
Power cables: The power cords have been connected to the PSU modules on the subsys-
tem and plugged into main power.
Ambient temperature: All the subsystem components have been acclimated to the sur-
rounding temperature.
5.4.2
Power On Sequence
When powering on the subsystem, please follow the steps below:
1. Power on any expansion enclosures if applied
If you connect any expansion enclosures to the subsystem, power on those expansion
enclosures before powering on the subsystem.
2. Power on the subsystem
dure for the subsystem is described in Section 5.4.3 Power On Procedure.
3. Host computers
Host computers should be the last devices that are turned on. Please refer to the docu-
mentation that came with your host computers to see its own power on procedure.
5.4.3
Power On Procedure
1. Plug in all power cords to the power connectors located at the rear of the subsystem. Use
the power cables that came with the subsystem to connect the subsystem to the power
outlet, separate power sources, or UPS devices.
2. Turn on the power supply switches for both power supply units.
3. The subsystem is now turned on and the self-test will start automatically.
4. The “Power” LED on the front LCD panel will turn blue.
CAUTION!
Although the PSUs are redundant and a single PSU can provide sufficient power to the sys-
tem, it is advisable to turn both the power switches on. If only one PSU is operating and fails,
the whole system will shut down.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Connection and Operation | en
39
5.4.4
Power On Status Check
Once the subsystem has been powered on, the status of the entire subsystem should be
checked to ensure that everything is running smoothly and that there are no complications or
malfunctions.
1. Controller module LEDs: The controller module LEDs should all flash green.
2. Drive tray LEDs: The LEDs of all the drive trays (that contain hard drives) should be con-
stantly lit green to indicate that the drives have successfully spun up and are ready for
I/Os.
3. LCD panel LEDs: The blue LED on the LCD panel should come on indicating that power is
being supplied to the system.
4. Firmware and Bosch RAIDWatch: The overall status of the system may be checked using
the terminal interface or the Bosch RAIDWatch GUI.
5. Audible alarm: If any errors occur during the initialization process, the onboard alarm will
sound in a hastily repeated manner.
Drive tray LEDs should normally start flashing during the initialization stage, indicating the
RAID controller unit is attempting to access the hard drives.
NOTICE!
The subsystem has been designed to run continuously. If a hot-replaceable component fails,
the fault can be corrected online.
i
5.4.5
LCD Screen
When powering on the subsystem, the following messages should appear on the front panel
LCD screen. Wait for the front panel LCD to show “READY” or “No Host LUN” before turning
on the host computer. Refer to Figure 5.3 on how to read the screens.
Fig. 5.3 The LCD Initial Screen
The LCD screen startup sequence is shown and described in the sequence below:
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
40 en | Subsystem Connection and Operation
RAID Subsystem DVA-08K | Installation Manual
This screen appears when the PSUs are turned
on.
Proceeding with controller self-test.
Self-test completed.
Verifying installed cache memory.
DVA-08K
System is ready. You can now start to config-
ure the subsystem.
DVA-08K
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Connection and Operation | en
41
5.5
Power Off Procedure
If you wish to power down the subsystem, please follow these steps:
NOTICE!
If you wish to power down the subsystem, please ensure that no time-consuming processes,
like “Regenerate Logical Drive Parity” or a “Media Scan,” are running.
i
1. Stop I/O access to the system
Stop all I/O accesses from the host computers to the subsystem. Please refer to the
related documentation of your host applications and operating system.
2. Disconnect the host
The host must be disconnected from the subsystem. To do this, disconnect the cables
from both the host and the subsystem.
3. Flush the cache
Use the “Shutdown Controller” function to flush all cached data. This prepares the RAID
subsystem to be powered down.
4. Turn off the power
Turn off the power switches at the power supply modules. Once the RAID subsystem has
been powered down, other devices that are connected to the subsystem can be powered
down.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
42 en | Subsystem Maintenance
RAID Subsystem DVA-08K | Installation Manual
6
Subsystem Maintenance
Constant monitoring and maintenance of your SATA-based subsystems will minimize the
chance of system downtime and preserve the working integrity of the system for a longer
period of time. If any of the subsystem plug-in modules fails, they must be replaced as soon as
possible.
6.1
Overview
CAUTION!
Do not remove a failed component from the subsystem until you have a replacement on hand.
If you remove a failed component without replacing it, the internal airflow will be disrupted
and the system will overheat causing damage to the subsystem.
All of the following components can be replaced in case of failure:
6. Hard drives – Section 6.7.2 Replacing a Failed Hard Drive
6.1.1
General Notes on Component Replacement
•
With the exception of the RAID controller module, all the components on the subsystems,
including the PSU modules, cooling fan modules, BBU, and drive trays are hot-swappable
and can be changed while the subsystem is still in operation.
•
Qualified technicians who are familiar with the subsystem should be the only ones who
make component replacements. If you are not familiar with the subsystems and not famil-
iar with RAID subsystem maintenance in general, it is strongly advised that you refer sub-
system maintenance to a suitably qualified maintenance technician.
•
Normalized airflow is directly dependent upon the presence of all subsystem compo-
nents. Even if a subsystem component fails, it should not be removed from the subsys-
tem until a replacement is readily at hand and can be quickly installed. Removing a
subsystem component without a replacement can lead to permanent subsystem damage.
When replacing any hot-swappable component, caution should be taken to ensure that
the components are handled in an appropriate manner. Rough or improper handling of
components can lead to irreparable damage.
•
•
When removing a controller module from the subsystem, ensure that the power has been
turned off and that all precautionary measures, without exception, are adhered to. The
controller board contains very sensitive components and can be easily damaged.
CAUTION!
When inserting a removable module, DO NOT USE EXCESSIVE FORCE! Forcing or slamming a
module can damage the pins on the module connectors either on the module itself or on the
backplane. Gently push the module until it reaches the end of module slot. Feel the contact
resistance and use slightly more force to ensure the module connectors are correctly mated. If
the module comes with extraction levers or retention screws, use them to secure the module.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Maintenance | en
43
6.2
Replacing Controller Module Components
6.2.1
Overview
The controller module should never be removed unless the following replaceable components
need to be accessed:
•
•
Cache memory DIMM module: If a larger capacity DIMM module is required.
Controller module itself: If the controller module in a single-controller model fails, it is
necessary to power down the subsystem and replace the controller.
If a DIMM module or RAID controller fails, contact your vendor immediately for a replacement.
To replace any of these components, the controller module must first be removed from the
subsystem.
6.2.2
Notes on Controller Module Maintenance
•
•
•
The controller module contains a DIMM module. It is not recommended to re-use the
DIMM module extracted from a failed controller unless you have a similar RAID subsystem
that can be used to test the module. You can contact your vendor for sending the failed
controller in for repair.
When replacing the controller module, it must be remembered that the controller board
is one of the most sensitive components in the subsystem. All previously stipulated safety
precautions must be strictly adhered to. Failure to adhere to these precautions can result
in permanent damage to the controller board, resulting in lengthy delays.
Prior to replacing the controller module, it is imperative for your own safety to be sure no
power is being supplied to the system.
6.2.3
Removing the Controller Module
To remove the controller module:
1. Stop host I/Os or host applications to avoid losing data or causing data inconsistency.
2. Turn the subsystem power off: If possible power off the subsystem in the way described
in Chapter 4. If it is not possible to do this turn off both PSU modules and disconnect the
power cords.
3. Disconnect all cables: There may be a number of different cables attached to the control-
ler module. These cables could include SCSI cables for host connections, an RS-232C
(audio jack) cable for serial port connection, and an Ethernet cable for network connec-
tion. Prior to removing the controller module, all these cables should be removed.
4. Loosen the retention hand screws: Hard screws are located on both sides of the RAID
controller’s faceplate. Press these screws and use a Phillips screwdriver to loosen them
so that the controller can be removed from chassis. (See Figure 6.1)
Fig. 6.1 Loosen Controller Module Retention Screws
5. Pull the controller module out: Once the retention screws have been removed; gently pull
the controller module out of the subsystem chassis.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
44 en | Subsystem Maintenance
RAID Subsystem DVA-08K | Installation Manual
6.2.4
Replacing the Controller Module
1. Remove the failed controller module.
2. Install a DIMM module on the new controller module.
3. Insert the replacement controller. Align the controller module with the module bay at the
rear of the subsystem. Gently slide the controller module in.
4. Fasten the hand screws. Once the controller module has been completely inserted into
the subsystem chassis, secure the controller module to the chassis by tightening the
hand screws at the sides of the controller rear panel.
5. Connect the controller module cables: Reconnect all of the cables that were previously
disconnected from the controller module. These may include SCSI cables for host and
expansion connections, an RS-232C (audio jack) cable for serial port connection, and an
Ethernet cable for network connection.
6. Power on: Once the new controller module has been properly installed and the cables
have been correctly connected, turn the subsystem power on.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Maintenance | en
45
6.3
Replacing or Upgrading Memory Modules
6.3.1
Memory Module Installation Overview
•
The subsystems come with a pre-installed 256MB (or above) DDR RAM DIMM module on
the controller. The controller supports one memory module for the capacity up to 1GB. If
a DDR RAM DIMM modules with a different size is preferred or the original memory mod-
ule has failed in some way, the pre-installed module must be removed and replaced by a
new one. Replacement and installation instructions are described fully below.
The DIMM module is located on the controller board. The controller board is a sensitive
component and must be treated with care to avoid being damaged.
•
CAUTION!
The controller board in the module contains sensitive components. Please ensure that all anti-
static precautions stipulated above are strictly adhered to. Only qualified technicians can
replace a DIMM module.
6.3.2
Selecting a Memory Module
If the memory module mounted on the controller is going to be replaced, the following factors
should be considered when purchasing replacement modules.
•
Pre-installed DIMM module: The subsystem comes with a 256MB DDR RAM module pre-
installed on the controller board. If you wish to change the size of the DIMM, then a new,
separately purchased DIMM can be installed.
•
•
DDR RAM DIMM modules supported. The subsystems support DDR RAM DIMM modules
with the capacities ranging from 256MB to 1GB.
Installation consideration: When installing the DIMM module, it is necessary to handle the
controller module. The controller board is more susceptible to damage than the other
components and must therefore be handled with extreme care. All anti-static precautions
must be strictly adhered to.
•
•
Secure installation: When replacing the DIMM module, make sure that the new DIMM
module is firmly in place prior to installing the controller module. If the DIMM module is
not firmly in place, the subsystem will not run and the controller will need to be removed
and the DIMM module correctly installed.
Purchasing consideration: When purchasing a DDR RAM DIMM to install on the controller
board, contact your vendor for an updated list of certified modules.
6.3.3
DIMM Module Installation
CAUTION!
The pre-installed modules must be removed prior to installing new memory modules. Do this
with care. Sensitive components can be damaged during the process.
If a DIMM module fails or a DIMM module with a higher memory capacity is required, the
DIMM module must be replaced.
1. Remove the controller module.
2. Remove the previously installed DIMM module from the DIMM socket. To do this, push
the white module clips on the sides of the DIMM module down together. By doing this,
the previously installed modules will be ejected from the DIMM socket. (See Figure 6.2)
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
46 en | Subsystem Maintenance
RAID Subsystem DVA-08K | Installation Manual
Fig. 6.2 Push Back the Module Clips on the Sides of the DIMM Socket
3. Gently retrieve the DIMM module out of the DIMM socket. (See Figure 6.2)
4. Insert the DIMM module into the DIMM socket. Align the DIMM module with the DIMM
socket. Once aligned, gently push the DIMM module into the socket. The white clips on
the sides of the socket will close automatically and secure the DIMM module into the
socket.
Fig. 6.3 Insert the DIMM Module
5. Reinstall the controller module. After the DIMM module has been properly installed, the
controller module must be reinstalled. To do this, align the controller module with the
controller module bay. Then gently push the controller module in the controller bay.
Carefully push the controller until you feel the contact when the board edge connectors
are mated to the backplane. Do not use force. If unusual contact resistance is felt, try it
again. Next secure the controller module into the subsystem by fastening the hand
screws on the sides.
NOTICE!
When replacing a DIMM, the whole subsystem needs to be powered down. Therefore, when
replacing a DIMM, you should carefully select the time when the replacement will be made in
order to minimize the overall disruption to service.
i
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Maintenance | en
47
6.4
Replacing a Faulty BBU
NOTICE!
The BBU is hot-swappable and can be replaced while the subsystem is running. However, a
new module will only be recognized after a subsystem reset. Carefully select the time when
the reset will be made in order to minimize the overall disruption to service.
i
To replace a faulty BBU, please follow these steps:
1. Remove the faulty BBU module from the chassis. The BBU module is secured to the chas-
sis with two (2) spring screws. These screws must be loosened. To loosen, turn the
screws counterclockwise.
2. Install the new BBU module. After the faulty BBU module has been removed, the new
BBU module can be installed. To do this, align the BBU module with the empty slot, and
then gently push the BBU module into the slot.
3. Secure the BBU module to the enclosure. Tighten the two (2) spring screws on the back
of the BBU module.
4. Once the new BBU module is correctly installed into the subsystem, the LED should start
flashing, indicates the BBU is being charged. When the BBU is fully charged, the LED will
go off.
NOTICE!
The life expectancy of a BBU is approximately 500 cycles. Follow the procedures above to
i
replace an old BBU with a new BBU in order to maintain fault-tolerant subsystem functional-
ities.
6.5
Replacing a Failed PSU Module
6.5.1
Notes on PSU Module Maintenance
•
Two redundant PSU modules: The subsystem comes with two 350W, fully redundant, hot-
swappable PSU modules. These modules are accessed from the rear of the subsystem.
Immediate replacement: When a PSU fails, it should ideally be replaced immediately. Do
not remove the PSU module unless a replacement is readily available. Removing a PSU
without a replacement will cause severe disruptions to the internal airflow and the sub-
system will overheat, possibly causing irreparable damage to some of the subsystem
components.
•
•
PSU bracket: Each PSU module is permanently mounted in a two-level steel bracket, cre-
ating a single unit. The PSU is located in the upper level and a removable cooling fan
module is mounted in the lower level.
CAUTION!
Although the subsystems can operate using single PSU module, it is not advisable to run the
RAID subsystems with a single PSU module for an extended period of time.
6.5.2
Replacing the PSU Module
To replace a PSU, please follow these steps:
1. Turn off the PSU and remove the power cord: Turn of the power switches located on the
right side of each power supply module.
2. Once the power switches have been turned off, remove the power cables that connect
the subsystem to the main power. The power connector is found on the left side of each
power supply module.
3. Remove the retention screw: After the power cable has been removed from the power
connector, remove the retention screw at the upper right side of the PSU rear-end panel.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
48 en | Subsystem Maintenance
RAID Subsystem DVA-08K | Installation Manual
The screw is located below the extraction lever, beside the LED indicator, and can be hid-
den from sight.
Fig. 6.4 PSU Parts Identification
4. Pull the extraction handle downward: Push the extraction lever at the back of the PSU
module downwards. This will dislodge the PSU module from the subsystem. Once dis-
lodged, gently pull the PSU module out of the subsystem.
CAUTION!
•
When a PSU is pulled out of the chassis, the fan module beneath the PSU is removed
from the chassis at the same time.
•
Do not remove the PSU module unless a replacement is readily available. Removing a PSU
without a replacement will cause severe disruptions to the internal airflow and the sub-
system will overheat, possibly causing irreparable damage to some of the subsystem
components.
•
It is recommended that the replacement procedure is completed in less than five (5) min-
utes to prevent the subsystem from overheating.
5. Remove the cooling module: To do this, push the clips on either side of the module rear
panel together. Then gently pull the cooling module out of the lower level of the PSU
bracket. (See Figure 6.5)
Fig. 6.5 Remove the Cooling Module
6. Reinstall the cooling module into the new PSU module: To do this, align the cooling mod-
ule with the lower level of the PSU bracket and gently slide the cooling module in.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Maintenance | en
49
7. Insert the new PSU module into the subsystem: Once the previously removed cooling
module has been installed, insert the new PSU module into the subsystem. Make sure the
extraction lever is in its downright position so that the saddle notches on the lower edges
of the handle can lock on to the edge metal brackets along the chassis inner walls. Push
the PSU into the slot and pull the handle upwards to secure the module.
8. Reinsert the retention screw: If the PSU module is properly installed, the back end of the
module should be aligned with the enclosure’s rear panel. To firmly secure the PSUs into
place, reinsert the retention screw.
9. Reconnect the power cord and turn the power on: Plug the power cord into the socket on
the PSU module and turn the PSU module power switch on.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
50 en | Subsystem Maintenance
RAID Subsystem DVA-08K | Installation Manual
6.6
Replacing a Failed Cooling Fan Module
6.6.1
Notes on Cooling Fan Module Maintenance
•
•
•
Redundant cooling fan modules: The subsystems are equipped with two redundant, hot-
swappable, single-blower cooling fan modules located in the lower PSU module slot.
These cooling fan modules control the internal operational temperature of the subsystem
and therefore their working integrity should be maintained at all times.
Detecting a failed cooling fan module: If a cooling fan module fails, you can be notified of
the failure by the LED located at the back of the module, an audible alarm, the terminal
event prompts, the Bosch RAIDWatch Panel View, or through the various methods by the
Configuration Client utility.
Replacing a cooling fan module: Once you are notified that a cooling fan module has
failed, it should be replaced as soon as possible. A failed cooling fan module should only
be removed from the subsystem when you have an immediately available replacement
module that can be installed as soon as the failed cooling fan module has been removed.
CAUTION!
•
•
•
The latches at the back of the cooling fan module secure the cooling fan module into the
enclosure. If these latches are broken, the warranty on the cooling fan module will be
void.
Although the cooling fan modules are fully redundant, it is not advisable to run the sub-
systems with any of the cooling fan modules missing. Whenever a cooling fan module
fails, the system is at risk of sustaining irreparable damage.
Keep a failed module in its enclosure bay until a replacement unit is in hand.
6.6.2
Replacing a Cooling Fan Module
The cooling fan modules are secured to the chassis with two black latches located on the rear
of the module. To replace the cooling fan module, please follow these steps:
1. To remove the cooling fan module: Squeeze both side latches towards the center of the
cooling fan module and gently withdraw the cooling fan module from the subsystem by
gently pulling on the silver handle at the bottom. (See Figure 6.6).
Fig. 6.6 Removing the Cooling Fan Module
CAUTION!
Forcing or slamming a module into place can damage the connector pins on the module itself
or that on the subsystem backplane.
2. Install the new cooling fan module: Line the new module up with the slot into which it
will be inserted and then gently push it into the chassis. The latches will hold the module
in place.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Maintenance | en
51
6.7
Drive Tray Maintenance
6.7.1
Notes on Hard Drive Maintenance
•
Hot-swappable drive trays: The drive trays are all hot-swappable. If a hard drive fails, it
can be replaced while the subsystem is still running.
•
Forearm handles: If the hard drive is behind either the left or right forearm handle, make
sure that the locking mechanism on the side of the handle is first released prior to open-
ing the handle itself. (See Figure 6.7) The locking mechanism must also be released in
order to close the handle. Therefore, after the new drive has been installed, it will be nec-
essary to release the locking mechanism on the handle prior to closing it.
Fig. 6.7 Forearm Handle Locking Mechanism
•
•
•
Front flap mechanism: Do not leave a drive tray’s front flap open. The front flap and its
key-lock secure a drive tray to chassis slot. A disk drive operating with the half-open front
bezel may result in signal glitches and Data Compare Errors might ensue.
Remove drives slowly: Although the drive trays are designed to be hot-swappable, when
removing a drive tray from the subsystem, withdraw it from the chassis slowly. Removing
the drive tray too quickly may cause a drive I/O timeout.
Replacement on hand: If a hard drive has failed, make sure you have a replacement hard
drive readily available before removing the failed drive from the subsystem. Do not leave
the drive tray slot open for an extended period of time. If the drive tray slot is left unoccu-
pied for an extended period of time, the airflow will be disrupted and subsystem compo-
nents will overheat and may be permanently damaged.
6.7.2
Replacing a Failed Hard Drive
To replace a hard drive, please follow these steps:
CAUTION!
•
Handle hard drives with extreme care. Hard drives are very delicate. Dropping a drive
onto a hard surface (even from a short distance) and hitting or touching the circuits on
the drives with your tools may all cause damage to drives.
•
•
Observe all ESD prevention methods when handling hard drives.
Only use screws supplied with the drive canisters. Longer screws may damage the drive.
CAUTION!
The hard drives and drive trays should only be installed into the subsystem once the subsys-
tem has been mounted into a rack cabinet. If the hard drives are installed first, the subsystem
will be too heavy to place into position and the possible impact during installation may dam-
age your drives.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
52 en | Subsystem Maintenance
RAID Subsystem DVA-08K | Installation Manual
Hard drives for the subsystem can be purchased separately. When purchasing the hard drives,
the following factors should be considered:
•
•
•
Capacity (MB/GB): Use drives with the same capacity. RAID arrays use a “least-common-
denominator” approach. The maximum capacity of each drive used in the array is the
maximum capacity of the smallest drive. Use drives of the same capacity.
Profile: The drive trays and bays of the system are designed for 3.5-inch wide x 1-inch
high hard drives. It is highly recommended that you do not try to use drives of any other
size.
Drive type: The subsystem can use either SATA-II or SATA-I hard drives.
1. Identify the drive tray that contains the hard drive that needs to be replaced.
CAUTION!
Replacing the wrong drive in an array can fatally fail a RAID configuration. You should identify
a failed drive from the Bosch RAIDWatch GUI screen, by checking the drive slot ID in the termi-
nal screen, by checking the LEDs on the drive tray panel, and/or use the identify/flash drive
function in firmware.
2. Open the front flap: Once the drive tray has been identified, push the release button at
the drive bezel. (See Figure 6.8) The front bezel will automatically be lifted and the drive
tray should be easily dislodged from the chassis.
unlocked. (See Figure 6.9) To do this, turn the key-lock on the front of the drive tray until
the groove on its face is in a horizontal orientation.
Fig. 6.9 Drive Tray Key-Lock Rotation
4. Remove the drive tray along with the hard drive in it. Once the drive tray is dislodged
from the chassis, gently and carefully withdraw the drive tray from the chassis.
5. Remove the hard drive from the drive tray: Loosen the four retention screws (two on each
side) to remove the hard drive from the drive tray.
6. Install the new hard drive:
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Subsystem Maintenance | en
53
7. Place the SATA hard drive into the drive tray (as shown in Figure 6.10) making sure that
the hard drive is oriented in such a way that the drive’s SATA connector is facing the back
of the drive tray.
Fig. 6.10 Installing a SATA Hard Drive
8. Adjust the drive’s location until the mounting holes in the drive canister are aligned with
those on the hard drive. Secure the drive with four supplied 6/32 flathead screws. (See
Figure 6.10)
CAUTION!
Only use screws supplied with the drive canisters. Longer screws may damage the drive.
9. If the failed drive is a member of a RAID 1, 3, or 5 array, once it is replaced the subsystem
should immediately start to rebuild the array. The drive activity LEDs should start to flash.
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
54 en | Appendix: Technical Specifications
RAID Subsystem DVA-08K | Installation Manual
7
Appendix: Technical Specifications
Environmental Specifications
Humidity
5 to 95% (non condensing – operating and non-operating)
Temperature
Operating: 0º to 40ºC
Non-operating: -40º to 60ºC
Altitude
Sea level to 12,000ft – operating
Sea level to 20,000ft – non-operating
Power Requirements
Input Voltage
115VAC @ 6A
240VAC @ 3A with PFC
(auto-switching)
Frequency
47-63Hz
350W
Power Consumption
Dimensions
Height
w/o front handles
88mm
w/ front handles
88mm
Width
446mm
490mm
482mm
505mm
Length
Package dimensions: 344H x 600W x 670D mm
System Weight
Net weight: 23.5kg
Gross weight: 25.0kg (without disk drives)
EMI/EMC
FCC Class-B
CE
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Appendix: Technical Specifications | en
55
Safety Requirements
UL
CB
Shock
Half-sine
Operating: 5G peak, 11ms duration
Non-operating: 15G, 11ms, half-sine
Vibration
0.5oct/min
Operating
Non-operating
0.5oct/min
Warning Alarms
•
•
•
•
LCD screen messages
Audible alarms
System LEDs
Event notification via the Bosch RAIDWatch Manager (LAN broadcast, email, fax,
MSN, ICQ, SMS, and SNMP traps) and RS-232C terminal display
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
56 en | Appendix: Technical Specifications
RAID Subsystem DVA-08K | Installation Manual
7.1
Controller Specifications
7.1.1
Configuration
Specifications
RAID Levels
0, 1(0 + 1), 3, 5, 10, 30, 50, JBOD, and non-RAID disk spanning
Host OS independent; supports all major platforms
Host OS Compatibil-
ity
Host Interface
Host Channels
Drive Interface
2 SCSI-320 channels via 2 dual-stacked VHDCI connectors
2 pre-configured SCSI-320 host channels
Supports 8 channel connection to 3Gbps SATA-II disk drives,
SATA-I backward compatible
Drive Channels
All drive channels are pre-configured, routed through a back-end
PCB and cannot be changed
Caching Mode
Cache Memory
Write-through or Write-back
Pre-installed 256MB (or above) DDR RAM DIMM with/without
ECC, in one DIMM socket
Number of LUN’s
Up to 32 per host ID
Yes
Multiple Target IDs/
Host Channel
Firmware on Flash
Memory
Yes
7.1.2
Architecture
Specifications
IBM PowerPC 750CXr
CPU
Gigabit Ethernet
DIMM Slot
ASIC
One 10/100BasedT for local or remote management access
One 184-pin DDR DIMM module
64-bit chipset (ASIC266)
32Mbit (4MB)
Flash ROM
NVRAM
32KB with RTC
Hardware XOR
Real-time Clock
Yes
For event messages with time record tracking and scheduled
maintenance tasks, e.g., Media Scan.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Appendix: Technical Specifications | en
57
7.2
Drive Tray Specifications
Specifications
Height
Width
28mm
110mm
218.92mm
Yes
Depth
Key Lock
7.3
Power Supply Specifications
Specifications
350W
Nominal Power
DC Output
12.0V: 25A
5.0V: 25A
3.3V: 20A
Input Frequency
AC Input
47 to 63Hz
115VAC @ 6A or 240VAC @ 3A with PFC
Yes
Power Factor Correction
Hold-up Time
At least 16ms at 115/230VAC full load after a loss of
AC input
Over-temperature Protection
Cooling Fans
Auto shutdown when cooling is lost or elevated tem-
perature is detected; over-voltage protection is also
available.
Two fans for each unit (inside PSU)
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
58 en | Appendix: Technical Specifications
RAID Subsystem DVA-08K | Installation Manual
7.4
Cooling Module Specifications
Specifications
Speed
High or low rotation speed controlled by firmware
Max. Air Flow (each module)
High speed: 31.8 CFM
Low speed: 20.1 CFM
Input Power
Rated Voltage
Temperature
9/3.12W max.
DC 12V
Operating: -10 to +60ºC
Storage: -20 to +70ºC
7.5
RAID Management
Specifications
Configuration
LCD keypad panel
Text-based firmware-embedded utility over RS-232C connection
through the included audio jack-to-DB-9 serial cable
The Bosch RAIDWatch Manager program using Ethernet connec-
tion
Performance Monitor-
ing
Yes
Remote Control and
Monitoring
Yes
Event Notification
Yes (via Bosch RAIDWatch’s sub-modules, Configuration Client
or NPC)
Management Connec-
tion
In-band over Ethernet, or RS-232C
Configuration on Disk
Configuration data stored on disk drives for logical drive assem-
blies to exist after controller replacement; basic settings, e.g.,
channel mode settings, are stored on NVRAM
Failure Indicator
Via audible alarm, LCD keypad panel, Bosch RAIDWatch Man-
ager session, event notifications, or event prompts on terminal
emulation
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Appendix: Technical Specifications | en
59
7.6
Fault Tolerance Management
Specifications
SATA drive SMART support
Battery Back-up Option
Yes
Yes
2
Yes
ISEMS (Bosch Simple Enclosure Management Service) via I C Interface
Automatic Drive Failure Detection
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Regenerate Logical Drive Parity
Bad Block Reassignment
Automatic Rebuild upon Failed Drive Replacement
Automatic Rebuild on Spare Drives
Manual Clone of Suspected Failed Drive
Concurrent rebuild on Multiple Drives in a RAID (0 + 1) Logical Drive
nd
Salvage the 2 Temporarily Failed Drive in a RAID 1, 3 or 5 Logical Drive
st
Yes
Salvage the 1 Temporarily Failed Drive in a RAID 0 Logical Drive
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
60 en | Appendix: Spare Parts and Accessories
RAID Subsystem DVA-08K | Installation Manual
8
Appendix: Spare Parts and Accessories
8.1
Spare Parts
8.1.1
Spare Parts Overview
Except the RAID controller module, all the active components in the subsystems can be
replaced while the system is running. If any of these components fails then it can, if config-
ured in a fully redundant mode, be hot-swapped. Spare parts for the subsystems can be
ordered separately. This section lists the model names for the different spare parts.
8.1.2
Spare Parts List
Table 8.1 lists the spare parts.
Model Name
DVA-ADTK-000A
Description
Drive tray, type-III bezel and type-II LED lightpipe.
Drive tray including 500 GB Hitachi SATA drive
Drive tray including 750 GB Hitachi SATA drive
DVA-ADTK-050A
DVA-ADTK-075A
DVA-SPKK-08A
Power supply module, E2U DDR-interface subsystems,
350W capacity.
DVA-SFAK-08A
Dual-speed version of cooling fan module: r 2U subsystems
Battery cell pack, Li-ION battery cells
DVA-SBBK-00A
Table 8.1 Spare Parts List
8.1.3
Controller Modules
Table 8.2 lists the control modules.
Model Name
Description
DVA-SCDK-08A
SCSI-to-SATA RAID controller module, 2 x SCSI-320
host channels, 8 x SATA II drive channels, 256MB DDR
RAM.
Table 8.2 Controller Module List
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Appendix: Spare Parts and Accessories | en
61
8.2
Accessories and Optional Items
A number of accessory items are available for the RAID subsystem. Some of these accessory
items come with the subsystem; but if damaged or if more accessory items are needed, they
can be ordered separately. Available accessory items are listed below:
Model Name
DVA-ACON-HD68A
Description
SCSI external round cable, DB68-to-VHDCI
DVA-ACON-VD68A
External SCSI round cable, VHDCI-to-VHDCI
* One included in the shipping package
DVA-ACON-VD680A
External SCSI round cable, VHDCI-to-VHDCI (0,5 m)
* One included in the shipping package
DVA-ASRK-28A
Slide rails for 21"~28.5" deep racks
Slide rails for 23"~36" deep racks
DVA-ASRK-36A
Table 8.3 Accessories List
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
62 en | Appendix: Pinouts
RAID Subsystem DVA-08K | Installation Manual
9
Appendix: Pinouts
9.1
SCSI Port: VHDCI Connector Pinouts
The SCSI port connector pinouts comply with specifications in T10 Working Draft, Project
1365D, SCSI Parallel Interface-4.
* NC = No Connection, * GND = Ground,
* TPWR = Terminator Power
Pin
1
Name
SD12+
SD13+
SD14+
SD15+
SDP1+
SD0+
Pin
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
Name
SD12-
SD13-
SD14-
SD15-
SDP1-
SD0-
2
3
4
5
6
7
SD1+
SD1-
8
SD2+
SD2-
9
SD3+
SD3-
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
SD4+
SD4-
SD5+
SD5-
SD6+
SD6-
SD7+
SD7-
SDP0+
GND
SDP0-
GND
DIFSENS
TPWR
TPWR
NC
GND
TPWR
TPWR
NC
GND
GND
SATN+
GND
SATN-
GND
SBSY+
SACK+
SRST+
SMSG+
SSEL+
SC_D+
SREQ+
SI_O+
SD8+
SBSY-
SACK-
SRST-
SMSG-
SSEL-
SC_D-
SREQ-
SI_O-
SD8-
Table 9.1 VHDCI Connector Pinouts
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Appendix: Pinouts | en
63
Pin
32
33
34
Name
SD9+
Pin
66
67
68
Name
SD9-
SD10+
SD11+
SD10-
SD11-
Table 9.1 VHDCI Connector Pinouts (Cont.)
9.2
COM1 Cable: DB9 and Audio Jack Pinouts
Fig. 9.1 Serial Port Cable CN1 and CN2 Connectors
CN1 Pin Number
Pin Name
1
2
3
Ground
TXD
RXD
CN2 Pin Number
Pin Name
1
2
3
4
5
6
7
8
9
NC
RXD
TXD
DTR
GND
DSR
RTS
CTS
NC
Pin 4 and Pin 6 are shorted
Pin 7 and Pin 8 are shorted
Table 9.2 COM 1 Cable, RS-232C (Audio Jack) Pin Out Definitions
NOTICE!
A null modem is used for wire-swap and is necessary for connecting in between COM1CN2
and a PC serial port.
i
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
64 en | Appendix: Pinouts
RAID Subsystem DVA-08K | Installation Manual
9.3
9.4
Null Modem
Swap Pin 2 and Pin 3
Swap Pin 4 and Pin 6
Swap Pin 7 and Pin 8
Table 9.3 Null Modem Pinouts
Ethernet Port Pinouts
Fig. 9.2 LAN Port Pinouts
Pin
Pin Name
LAN_TXP
Pin
Pin Name
1
5
N2
2
3
4
LAN_TXN
LAN_RXP
N2
6
7
8
LAN_RXN
N1
N1
Table 9.4 Ethernet Port Pinouts
9.5
Main Power
IEC-type receptacle.
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID Subsystem DVA-08K | Installation Manual
Index | en
65
10
A
I
airflow 20, 58
I2C 26, 33
array identification 12
audio jack 63
I2C bus 17
input voltage 54
international transportation regulation 14
Internet SCSI 7
iSCSI initiators 35
B
K
backplane 11
Key-Lock 52
BBU Warnings 20
blower 15
L
LAN Port LED 29
LCD 39
LCD Screen 39
LED 17
Bosch RAIDWatch 17
C
M
cabling 19
media scan 41
memory module 38
mini-SCSI connector 13
capacity 52
charge 14
component check 19
cooling module specifications 58
CPU 56
N
null modem 63
P
package dimensions 54
power cord 15
D
power down 41
power on 38
DB9 63
DIMM 43
power switch 15
PSU Bracket 47
PSU Module 27
drive IO timeout 51
drive trays 27
R
E
rack installation 19
rear brackets 23
ejection handle 48
Ethernet link 17
RJ-45 35
RJ-45 port 14
F
firmware 17
front flap 24
S
SATA drives 52
SCSI cable 35
G
GUI 17
sensors 31
H
shutdown controller 41
static free 19
status check 39
system dimensions 54
system weight 54
handles 51
host redundancy 37
hot-swap mechanism 12
hot-swappable 42
Bosch Security Systems
F.01U.027.797 | V2 | 2008.08
Download from Www.Somanuals.com. All Manuals Search And Download.
66 en | Index
RAID Subsystem DVA-08K | Installation Manual
T
terminal emulation program 17
terminal management 14
U
under charge 29
V
ventilation clearance 20
W
X
XOR 56
F.01U.027.797 | V2 | 2008.08
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems
Robert-Koch-Straße 100
D-85521 Ottobrunn
Germany
Telefon
Fax
+49 (89) 6290-0
+49 (89) 6290-1020
© Bosch Security Systems, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|