MX660/MX615/MS614 Digital Projector
User Manual
Welcome
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
Please read this manual before you
operate your projector. Save it for
future reference.
5.
In some countries, the line voltage is
NOT stable. This projector is designed
to operate safely within a mains
voltage between 100 to 240 volts AC,
but could fail if power cuts or surges
of 10 volts occur. In areas where the
mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a
power stabilizer, surge protector or
uninterruptible power supply (UPS).
2.
Do not look straight at the projector
lens during operation. The intense
light beam may damage your eyes.
6.
Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire. To
temporarily turn off the lamp, press
BLANK on the projector or remote
control.
3.
Refer servicing to qualified service
personnel.
4.
Always open the lens shutter (if any)
or remove the lens cap (if any) when
the projector lamp is on.
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety Instructions (Continued)
7.
The lamp becomes extremely hot
during operation. Allow the projector
to cool for approximately 45 minutes
prior to removing the lamp assembly
for replacement.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
11. Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause death
if you should come into contact with
live parts. The only user serviceable
part is the lamp which has its own
removable cover.
8.
Do not operate lamps beyond the
rated lamp life. Excessive operation of
lamps beyond the rated life could
cause them to break on rare occasions.
Under no circumstances should you
ever undo or remove any other covers.
Refer servicing only to suitably
qualified professional service
personnel.
9.
Never replace the lamp assembly or
any electronic components unless the
projector is unplugged.
12. When the projector is under
operation, you may sense some heated
air and odor from its ventilation grill.
It is a normal phenomenon and not a
product defect.
4
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
13. Do not place this projector in any of the 14. Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth
or any other item.
- Do not place inflammables near the
projector.
following environments.
- Space that is poorly ventilated or
confined. Allow at least 50 cm clearance
from walls and free flow of air around
the projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled
up.
- Locations where excessive humidity,
dust, or cigarette smoke may
contaminate optical components,
shorten the projector's life span and
darken the image.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
15. Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of,
or damage to, the lamp.
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 3000 m (10000 feet).
3000 m
(10000 feet)
16. Do not stand the projector on end
vertically. Doing so may cause the
0 m
(0 feet)
projector to fall over, causing injury or
resulting in damage to the projector.
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Safety Instructions (Continued)
17. Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector, doing
so may result in accidents and possible
injury.
Ceiling mounting the projector
We want you to have a pleasant
experience using your BenQ projector,
so we need to bring this safety matter to
your attention to prevent possible
damage to person and property.
If you intend to mount your projector
on the ceiling, we strongly recommend
that you use a proper fitting BenQ
projector ceiling mount kit and that
you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector
ceiling mount kit, there is a safety risk
that the projector may fall from the
ceiling due to an improper attachment
through the use of the wrong gauge or
length screws.
18. Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet, disconnect
it from the power supply's power outlet
and call BenQ to have the projector
serviced.
You can purchase a BenQ projector
ceiling mount kit from the place you
purchased your BenQ projector. BenQ
recommends that you also purchase a
separate Kensington lock compatible
security cable and attach it securely to
both the Kensington lock slot on the
projector and the base of the ceiling
mount bracket. This will perform the
secondary role of restraining the
projector should its attachment to the
mounting bracket become loose.
19. This product is capable of displaying
inverted images for ceiling mount
installation.
Hg - Lamp contains mercury. Manage in
accordance with local disposal laws.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it is
securely installed.
20. This apparatus must be earthed.
6
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
Network Settings allowing management of projector status from a computer using a web
browser
•
•
•
USB MINI-B jack to display computer signal through a USB cable
USB TYPE-A jack to present images stored on a USB flash drive
3D function to enjoy the 3D movies, videos, and sporting events in a more realistic way
by presenting the depth of the images
•
•
•
Filter free design to lower maintenance and operating costs
Brilliant color / VIDI to provide truer, more vibrant colors in picture
Closed captioning to display the dialogue, narration, and sound effects of TV programs
and videos
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Variable audio output
Wall color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
Selectable password protected function
3D color management allowing color adjustments to your liking
Selectable quick cooling function making the projector cool in a shorter time
FAQ to troubleshoot operational problems with one quick key press
Presentation timer for better control of time during presentations
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
Ability to display 16.7 million colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and economic modes to reduce the power consumption
Built-in speakers providing mixed mono audio when an audio input is connected
Component HDTV compatibility (YPbPr)
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items
are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
*The warranty card is only supplied in some specific regions. Please consult your dealer for
detailed information.
Projector
Power cord
VGA cable
Quick start guide
User manual CD
Warranty card*
Capture
Remote control with battery
Soft carry case
Pull the tab before using the remote control.
Optional accessories
1.
2.
Spare lamp kit
Ceiling mount kit
3.
RS232 cable
8
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector exterior view
1.
2.
Lamp cover
Front/upper side
External control panel
(See "Controls and functions" on page 10
for details.)
Vent (heated air exhaust)
Quick-release button
Top IR remote sensor
Focus and Zoom ring
Speaker grill
2
5
1
3.
4.
5.
6.
8.
9.
6
3
7
9
Front IR remote sensor
8
10. Projection lens
11. AC power jack
4
12. Rear adjuster foot
13. Ceiling mount holes
15. RS232 control port
16. USB ports
10
Rear/lower side
17. HDMI-input port
18. RGB signal output jack
19. RGB (PC)/Component Video (YPbPr/
YCbCr) signal input jack
20. S-Video input jack
Video input jack
18
19
15 16
22
20 21
17
11
21. Audio (L/R) input jacks
22. Audio input jack
Audio output jack
23. Kensington anti-theft lock slot
13
23
12
14
Introduction
9
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
9.
Projector
Lights up red if the projector's
temperature becomes too high.
LAMP indicator light
1
8
2
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
9
3
4
10
10. AUTO
Automatically determines the best picture
timings for the displayed image.
11
12
13
14
5
6
7
11. Keystone/Arrow keys (
Down)
/
Up,
/
11
Manually corrects distorted images
resulting from an angled projection.
1.
2.
3.
Focus ring
Adjusts the focus of the projected image.
Zoom ring
12.
Right/
Activates panel key lock.
When the On-Screen Display (OSD)
Adjusts the size of the image.
POWER indicator light
menu is activated, the #6, #11, and #12
keys are used as directional arrows to
select the desired menu items and to make
adjustments.
Lights up or flashes when the projector is
under operation.
MENU/EXIT
4.
5.
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
13. MODE/ENTER
Selects an available picture setup mode.
Activates the selected On-Screen Display
(OSD) menu item.
14. SOURCE
POWER
Toggles the projector between standby
mode and on.
Displays the source selection bar.
6.
7.
Left/
Starts the FAQ function.
BLANK
Used to hide the screen picture.
10
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
9.
Down)
/
Up,
/
8
1
2
resulting from an angled projection.
10. AUTO
9
10
11
12
3
Capture
Automatically determines the best
4
5
6
picture timings for the displayed image.
Right/
11.
13
9
Activates panel key lock.
14
When the On-Screen Display (OSD)
menu is activated, the #4, #9, and #11
keys are used as directional arrows to
select the desired menu items and to
make adjustments.
7
15
16
12. SOURCE
Displays the source selection bar.
13. MODE/ENTER
Selects an available picture setup mode.
1.
POWER
Toggles the projector between standby mode
and on.
Freeze
2.
3.
Activates the selected On-Screen Display
(OSD) menu item.
14. Timer On
Freezes the projected image.
CAPTURE
Captures the projected picture and save it as
your startup screen.
Activates or displays an on-screen timer
based on your own timer setting.
15. Timer Set up
4.
5.
6.
Left/
Enters presentation timer setting directly.
16. PAGE UP/PAGE DOWN
Starts the FAQ function.
BLANK
Operate your display software program
(on a connected PC) which responds to
page up/down commands (like Microsoft
PowerPoint).
Used to hide the screen picture.
Digital Zoom (+, -)
Magnifies or reduces the projected picture
size.
7.
8.
Volume +/-
Adjusts the sound level.
MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the top of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
•
Operating the projector from the front
•
Operating the projector from the top
C a
p t u r
e
Ca
ptur
e
Replacing the remote control battery
1.
Pull out the battery holder.
Please follow the illustrated instructions. Push and hold
the locking arm while pulling out the battery holder.
2.
Insert the new battery in the holder. Note the
positive polarity should face outward.
Push the holder into the remote control.
3.
•
Avoid excessive heat and humidity.
•
•
•
There may be battery damage if the battery is
incorrectly replaced.
Replace only with the same or equivalent type
recommended by the battery manufacturer.
Dispose of the used battery according to the battery
manufacturer's instructions.
•
•
Never throw a battery into a fire. There may be danger of an explosion.
If the battery is dead or if you will not be using the remote control for a long time, remove
the battery to prevent damage to the remote control from possible battery leakage.
12
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
3.
Rear Ceiling
Select this location with the projector placed Select this location with the projector
on the table in front of the screen. This is the suspended upside-down from the ceiling
most common way to position the projector behind the screen.
for quick setup and portability.
Note that a special rear projection screen
and the BenQ Projector Ceiling Mount Kit
are required for this installation location.
Set Rear Ceiling in the SYSTEM SETUP:
Basic > Projector Position menu after you
turn the projector on.
2.
Front Ceiling
Select this location with the projector
suspended upside-down from the ceiling in
front of the screen.
Purchase the BenQ Projector Ceiling Mount
Kit from your dealer to mount your
projector on the ceiling.
4.
Rear Table
Select this location with the projector placed
on the table behind the screen.
Set Front Ceiling in the SYSTEM SETUP:
Basic > Projector Position menu after you
turn the projector on.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM SETUP: Basic
> Projector Position menu after you turn
the projector on.
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Positioning your projector
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The distance from the projector lens to the screen, the zoom setting, and the video format
each factors in the projected image size.
For example, if you are using an 120-inch screen, the recommended projection distance is
4246 mm and the vertical offset is 137 mm.
If your measured projection distance is 5.0 m (5000 mm), the closest match in the "Distance
from screen (mm)" column is 5308 mm. Looking across this row shows that a 150'' (about
3.8 m) screen is required.
Projection dimensions
Refer to "Dimensions" on page 62 for the center of lens dimensions of this projector before
calculating the appropriate position.
Maximum zoom
Minimum zoom
Screen
Center of lens
Vertical offset
Projection distance
Screen size
Diagonal
Distance from screen (mm)
Min
Max
Vertical
offset
(mm)
length
length
W (mm) H (mm)
Average
(max.
(min.
Inch
mm
zoom)
zoom)
40
50
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7620
813
610
762
1231
1538
1846
2462
3077
3692
4615
6154
6769
7692
9231
1415
1769
2123
2831
3538
4246
5308
7077
7785
8846
10615
1600
2000
2400
3200
4000
4800
6000
8000
8800
10000
12000
46
57
1016
1219
1626
2032
2438
3048
4064
4470
5080
6096
60
914
69
80
1219
1524
1829
2286
3048
3353
3810
4572
91
100
120
150
200
220
250
300
114
137
171
229
251
286
343
There is 3% tolerance among these numbers due to optical component variations.
BenQ recommends that if you intend to permanently install the projector, you should
physically test the projection size and distance using the actual projector in situ before you
permanently install it, so as to make allowance for this projector's optical characteristics. This
will help you determine the exact mounting position so that it best suits your installation
location.
14
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
•
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 8). They are commercially available from electronics stores.
•
The connection illustrations below are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
Notebook or desktop computer
A/V device
Monitor
(VGA)
(DVI)
3
1
8
1
2
Speakers
8
6
10
4
5
7
8
9
or
or
1.
2.
3.
4.
VGA cable
VGA to DVI-A cable
USB cable
Component Video to VGA (D-Sub)
adapter cable
6.
7.
8.
9.
Video cable
Audio L/R cable
Audio cable
USB flash drive/USB wireless dongle
10. HDMI cable
5.
S-Video cable
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
15
•
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate
a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook.
Press FN and the labeled function key simultaneously. Refer to your notebook's
documentation to find your notebook's key combination.
•
•
The D-Sub output only works when an appropriate D-Sub input is made to the COMPUTER
1 jack.
If you wish to use this connection method when the projector is in standby mode, make
sure the Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See
"Standby Settings" on page 51 for details.
Connecting video source devices
You need only connect the projector to a video source device using just one of the
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the video source device as described below:
Terminal name
Terminal appearance
Picture quality
HDMI
Best
Component Video
S-Video
Better
Good
Video
Connecting audio
The projector has two built-in mono speakers which are designed to provide basic audio
functionality accompanying data presentations for business purposes only. They are not
designed for, nor intended for stereo audio reproduction use as might be expected in home
theater or home cinema applications. Any stereo audio input (if provided), is mixed into a
common mono audio output through the projector speakers.
The built-in speaker will be muted when the AUDIO OUT jack is connected.
•
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color
space to YUV. See "Changing Color Space" on page 24 for details.
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 16 for details.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
16
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
power outlet. Turn on the power outlet switch
(where fitted). Check that the POWER indicator
light on the projector lights orange after power has
been applied.
Please use the original accessories (e.g. power cord) only
with the device to avoid possible dangers such as electric
shock and fire.
2.
Press
POWER on the projector or
POWER on the remote control to start the
projector. As soon as the lamp lights up, a "Power On Tone" will be heard. The
POWER indicator light flashes green and stays green when the projector is on.
The start up procedure takes about 30 seconds. In the later stage of start up, a startup
logo is projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 33 for
details.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
3.
If the projector is activated for the first time,
select your OSD language following the on-
screen instructions.
4.
If you are prompted for a password, press the
arrow keys to enter a six-digit password. See
"Utilizing the password function" on page 21 for
details.
5.
6.
Switch all of the connected equipment on.
The projector will start to search for input
signals. The current input signal being scanned
displays in the upper left corner of the screen. If
the projector doesn't detect a valid signal, the message “No Signal” will continue
displaying until an input signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 24 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message “Out of Range” displayed on a blank screen. Please change to an input
signal which is compatible with the projector's resolution or set the input signal to a lower
setting. See "Timing chart" on page 63 for details.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the front
of the projector. Once the image is positioned
button to lock the foot in position.
2.
Screw the rear adjuster foot to fine-tune the
horizontal angle.
2
1
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly lower
the projector. Screw the rear adjuster foot in a reverse
direction.
Do not look into the lens while
the lamp is on. The strong light
from the lamp may cause
damage to your eyes.
If the projector is not placed on a flat surface or the
screen and the projector are not perpendicular to
each other, the projected image becomes trapezoidal.
To correct this situation, see "Switching input signal"
on page 24 for details.
Be careful when you press the
quick-release button as it is
close to the exhaust vent where
hot air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO on the
projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment
function will re-adjust the values of Frequency and Clock to provide the best picture quality.
The current source information will be displayed in the corner of the screen for 3 seconds.
•
•
The screen will be blank while AUTO is functioning.
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image size and clarity
1.
Adjust the projected image to the size 2.
that you need using the zoom ring.
Sharpen the image by rotating the
focus ring.
18
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, you will need to manually correct it following ONE of these steps.
•
Using the remote control
Press on the projector or remote control
/
to display the Keystone correction page. Press
to
correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the image.
Press
/
.
Press
/
.
•
Using the OSD menu
1.
2.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press to highlight Keystone and press MODE/ENTER. The Keystone correction
page displays.
3.
Press
to correct keystoning at the top of the image. Press
to correct
keystoning at the bottom of the image.
Operation
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
Below is the overview of the OSD menu.
Main menu icon
DISPLAY
Main menu
Off
Wall Color
Aspect Ratio
Keystone
Auto
ENTER
Position
Phase
Status
0
0
Sub-menu
H. Size
Digital Zoom
3D Sync
On
Press MENU/
EXIT to the
previous
page or to
exit.
3D Sync Invert
Teaching Template
Disable
Highlight
Current input signal
MENU
Exit
Analog RGB
The following example describes how to set the OSD language.
1.
Press MENU/EXIT on the projector or
remote control to turn the OSD menu on.
3.
Press
to highlight Language
to select a
and press
/
preferred language.
DISPLAY
Wall Color
Aspect Ratio
Keystone
Position
Phase
H. Size
Off
Auto
SYSTEM SETUP: Basic
Presentation Timer
Language
Projector Position
Menu Settings
English
Front Table
0
0
Digital Zoom
3D Sync
3D Sync Invert
Operation Settings
Remote Receiver
On
Disable
Front+Top
Off
BenQ
Panel Key Lock
Background Color
Splash Screen
MyScreen
Teaching Template
BenQ
MENU Exit
Analog RGB
MENU Exit
Analog RGB
4.
Press MENU/EXIT twice* on the
projector or remote control to
leave and save the settings.
2.
Use
/
to highlight the SYSTEM
SETUP: Basic menu.
SYSTEM SETUP: Basic
*The first press leads you back to the
main menu and the second press closes
the OSD menu.
Presentation Timer
Language
Projector Position
Menu Settings
English
Front Table
Operation Settings
Remote Receiver
Panel Key Lock
Front+Top
Off
Background Color
BenQ
BenQ
Splash Screen
MyScreen
MENU Exit
Analog RGB
20
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock,
such as the Kensington lock, to secure the projector. You can locate a Kensington lock slot on
the rear side of the projector. See item 23 on page 9 for details.
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the
lock’s documentation for finding out how to use it.
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the On-Screen
Display (OSD) menu.
WARNING: You will be inconvenienced if you activate the password functionality and
subsequently forget the password. Print out this manual (if necessary) and write the password
you used in this manual, and keep the manual in a safe place for later recall.
Setting a password
Once a password has been set and the power on lock is activated, the projector cannot be
used unless the correct password is entered every time the projector is started.
1.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings
menu. Press MODE/ENTER. The Security Settings page displays.
Highlight Change Security Settings and press MODE/ENTER.
2.
3.
As pictured to the right, the four arrow keys (
) respectively represent 4 digits (1, 2,
,
INPUT NEW PASSWORD
Power On Lock and Splash Screen Lock
use the same password.
,
,
3, 4). According to the password you desire to set,
press the arrow keys to enter six digits for the
password.
4.
Confirm the new password by re-entering the
new password.
Once the password is set, the OSD menu returns
to the Security Settings page.
MENU Back
5.
6.
To activate the Power On Lock function, press
/
to highlight Power On Lock and
to highlight Splash Screen
press
To activate the Splash Screen Lock function, press
Lock and press to select On.
/
to select On.
/
/
When the Splash Screen Lock is activated, the MyScreen function in the SYSTEM
SETUP: Basic menu will be password-protected.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected
password down here in this manual in advance or right after the password is entered so that it
is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
7.
To leave the OSD menu, press MENU/EXIT.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
21
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right displays
lasting for 3 seconds, and the INPUT PASSWORD
message follows. You can retry by entering another six-
digit password, or if you did not record the password in
Password Error
Please try again.
this manual, and you absolutely do not remember it, you can use the password recall
procedure. See "Entering the password recall procedure" on page 22 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
Entering the password recall procedure
1.
Press and hold AUTO on the projector or
remote control for 3 seconds. The projector
will display a coded number on the screen.
Write down the number and turn off your
projector.
Seek help from the local BenQ service
center to decode the number. You may be
required to provide proof of purchase
documentation to verify that you are an
authorized user of the projector.
RECALL PASSWORD
Please write down the recall code,
and contact BenQ
Customer Center.
2.
3.
Recall Code:
0 2 1 2
MENU
Exit
22
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the password
1.
Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security Settings >
Change Password menu.
2.
3.
Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears.
Enter the old password.
i. If the password is correct, another message “INPUT NEW PASSWORD” displays.
ii. If the password is incorrect, the password error message displays lasting for three
seconds, and the message “INPUT CURRENT PASSWORD” displays for your
retry. You can press MENU/EXIT to cancel the change or try another password.
Enter a new password.
4.
IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected
password down here in this manual in advance or right after the password is entered so that it
is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5.
6.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to the projector. Remember to enter the
new password next time the projector is started.
7.
To leave the OSD menu, press MENU/EXIT.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Change Security Settings menu after opening the OSD menu system. Press
MODE/ENTER. The message “INPUT PASSWORD” displays. Enter the current password.
i. If the password is correct, the OSD menu returns to the Security Settings page.
Press to highlight Power On Lock and press
have to enter the password next time when turning on the projector.
Press to highlight Splash Screen Lock and press to select Off. The Splash
/
to select Off. You will not
/
Screen function in the SYSTEM SETUP: Basic menu will be available for your
change.
ii. If the password is incorrect, the password error message displays lasting for three
seconds, and the message “INPUT PASSWORD” displays for your retry. You can
press MENU/EXIT to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time. When starting up, the projector automatically searches for
the available signals.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
To select the source:
Computer1/YPbPr1
•
Using the remote control or projector
Press one of the Source buttons on the remote control,
or press SOURCE on the projector repeatedly until
your desired signal is selected.
Computer2/YPbPr2
•
1.
Using the OSD menu
Press SOURCE on the projector or remote
control. A source selection bar displays.
HDMI
Video
2.
Press
/
until your desired signal is selected
and press MODE/ENTER.
S-Video
Once detected, the selected source information
will display at the corner of the screen for
seconds. If there is multiple equipment connected
to the projector, repeat steps 1-2 to search for
another signal.
Network Display
USB Display
•
The brightness level of the projected image will
change accordingly when you switch between
different input signals. Data (graphic) "PC"
presentations using mostly static images are
generally brighter than "Video" using mostly moving
images (movies).
USB Reader
•
•
The native display resolution of this projector is in a 4:3 aspect ratio. For best display
picture results, you should select and use an input signal which outputs at this resolution.
Any other resolutions will be scaled by the projector depending upon the “aspect ratio”
setting, which may cause some image distortion or loss of picture clarity. See "Selecting
the aspect ratio" on page 25 for details.
Firewall in the PC must be switched off to allow Q Presenter and USB Display to work.
Changing Color Space
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color space
to YUV.
To do this:
1.
2.
Press MENU/EXIT and then press
/
until the SOURCE menu is highlighted.
Press to highlight Color Space Conversion and press
space.
/
to select a suitable color
This function is only available when the HDMI-input port is in use.
24
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
•
Using the remote control
1.
Press Digital Zoom+/- to display the Zoom bar. Press Digital Zoom+ to magnify the
center of the picture. Press the key repeatedly until the picture size is suitable for your
need.
2.
3.
Use the directional arrows (
navigate the picture.
To restore the picture to its original size, press AUTO. You can also press Digital
Zoom-. When the key is pressed again, the picture is further reduced until it is restored
to the original size.
,
,
,
) on the projector or remote control to
•
Using the OSD menu
1.
2.
3.
4.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar displays.
Press repeatedly to magnify the picture to a desired size.
To navigate the picture, press MODE/ENTER to switch to the panning mode and press
the directional arrows (
the picture.
,
,
,
) on the projector or remote control to navigate
5.
To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out
function, and press AUTO to restore the picture to its original size. You can also press
repeatedly until it is restored to the original size.
The picture can only be navigated after it is magnified. You can further magnify the picture
while searching for details.
Selecting the aspect ratio
The “aspect ratio” is the ratio of the image width to the image height. Most analog TV and
some computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected picture ratio (no matter what aspect the source is):
1.
2.
3.
Press MENU/EXIT and then press
Press to highlight Aspect Ratio.
/
until the DISPLAY menu is highlighted.
Press
/
to select an aspect ratio to suit the format of the video signal and your
display requirements.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
25
About the aspect ratio
•
In the pictures below, the black portions are inactive areas and the white portions are
active areas.
•
OSD menus can be displayed on those unused black areas.
4.
16:9: Scales an image so that it is
displayed in the center of the
screen with a 16:9 aspect ratio.
This is most suitable for images
which are already in a 16:9 aspect,
like high definition TV, as it
displays them without aspect
alteration.
1.
Auto: Scales an image proportionally to fit
the projector's native resolution in its
horizontal or vertical width. This is suitable
for the incoming image which is neither in
4:3 nor 16:9 and you want to make most use
of the screen without altering the image's
aspect ratio.
15:9 picture
16:9 picture
5.
16:10: Scales an image so that it is
displayed in the center of the
screen with a 16:10 aspect ratio.
This is most suitable for images
which are already in a 16:10
aspect, as it displays them without
aspect alteration.
2.
Real: The image is projected as its original
resolution, and resized to fit within the
display area. For input signals with lower
resolutions, the projected image will display
smaller than if resized to full screen. You
could adjust the zoom setting or move the
projector towards the screen to increase the
image size if necessary. You may also need
to refocus the projector after making these
adjustments.
16:10 picture
4:3 picture
16:9 picture
3.
4:3: Scales an image so that it is displayed in
the center of the screen with a 4:3 aspect
ratio. This is most suitable for 4:3 images
like some computer monitors, standard
definition TV and 4:3 aspect DVD movies,
as it displays them without aspect
alteration.
4:3 picture
26
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the image
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Wall Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Wall Color menu and press
/
to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Light Yellow, Pink, Light Green, Blue, and Blackboard.
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
•
Press MODE/ENTER on the projector or remote control repeatedly until your desired
mode is selected.
•
Go to the PICTURE > Picture Mode menu and press
/
to select a desired mode.
1.
Dynamic mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2.
3.
Presentation mode: Is designed for presentations. The brightness is emphasized in this
mode to match PC and notebook coloring.
sRGB mode: Maximizes the purity of RGB colors to provide true-to-life images
regardless of brightness setting. It is most suitable for viewing photos taken with an
sRGB compatible and properly calibrated camera, and for viewing PC graphic and
drawing applications such as AutoCAD.
4.
5.
Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 27 for details.
Setting the User 1/User 2 mode
for your need. You can use one of the picture modes (except the User 1/2) as a starting point
and customize the settings.
1.
2.
3.
4.
Press MENU/EXIT to open the On-Screen Display (OSD) menu.
Go to the PICTURE > Picture Mode menu.
Press
Press
/
to select User 1 or User 2.
to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Picture Mode
sub-menu item.
5.
6.
Press
/
to select a picture mode that is closest to your need.
Press to select a menu item to be changed and adjust the value with
"Fine-tuning the image quality in user modes" below for details.
/
. See
7.
When all settings have been done, highlight Save Settings and press MODE/ENTER to
store the settings.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
27
8.
The confirmation message “Setting Saved” displays.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 is selected. Based on your needs, you can make adjustments to these
functions by highlighting them and pressing
/
on the projector or remote control.
Adjusting Brightness
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
+50
+70
+30
Adjusting Contrast
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
0
+30
-30
Adjusting Color
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in picture. It enables a
greater than 50% brightness increase in mid-tone images, which are common in video and
natural scenes, so the projector reproduces images in realistic and true colors. If you prefer
images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a color temperature
The options available for color temperature* settings vary according to the signal type
selected.
1.
T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2.
3.
4.
T2: Makes images appear bluish white.
T3: Maintains normal colorings for white.
T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
28
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
3D Color Management
In most installation situations, color management will not be necessary, such as in
classroom, meeting room, or lounge room situations where lights remain on, or where
building external windows allow daylight into the room.
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction,
should you require it.
Proper color management can only be achieved under controlled and reproducible viewing
conditions. You will need to use a colorimeter (color light meter), and provide a set of
suitable source images to measure color reproduction. These tools are not provided with the
projector, however, your projector supplier should be able to provide you with suitable
guidance, or even an experienced professional installer.
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you
select each color, you can independently adjust its range and saturation according to your
preference.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc, you can project any image
from the disc on the screen and enter the 3D Color Management menu to make
adjustments.
To adjust the settings:
1.
2.
Go to the PICTURE menu and highlight 3D Color Management.
Press MODE/ENTER on the projector or remote control and the 3D Color
Management page displays.
3.
4.
Highlight Primary Color and press
Green, Cyan, Blue, or Magenta.
Press to highlight Hue and press
/
to select a color from among Red, Yellow,
/
to select its range. Increase in the range will
include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected
Yellow
GREEN
RED
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Cyan
Magenta
5.
Press to highlight Saturation and adjust its
values to your preference by pressing
/
.
BLUE
Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6.
Press
to highlight Gain and adjust its values to your preference by pressing
/
.
The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.
Operation
29
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
8.
9.
Repeat steps 3 to 6 for other color adjustments.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1.
Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/
ENTER to display the Presentation Timer page.
2.
Highlight Timer Period and decide the time period by pressing
/
. The length of
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3.
Press to highlight Timer Display and choose if you want the timer to show up on
the screen by pressing
/
.
Selection
Description
Displays the timer on screen throughout the presentation
time.
Always
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never
Hides the timer throughout the presentation time.
4.
5.
Press
to highlight Timer Position and set the timer position by pressing
/
.
Top-Left
Bottom-Left
Top-Right
Bottom-Right
Press to highlight Timer Counting Direction and select your desired counting
direction by pressing
/
.
Selection
Count Up
Description
Increases from 0 to the preset time.
Decreases from the preset time to 0.
Count Down
6.
Press to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing . If you select On, a double beep sound will be heard at the
/
last 30 seconds of counting down/up, and a triple beep sound will be produced when
the timer is up.
7.
8.
To activate the presentation timer, press and press
MODE/ENTER.
A confirmation message displays. Highlight Yes and press MODE/ENTER on the
projector or remote control to confirm. You will see the message “Timer is On”
displaying on the screen. The timer starts counting when the timer is on.
/
to highlight On and press
To cancel the timer, perform the following steps:
1.
Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight Off. Press
MODE/ENTER. A confirmation message displays.
2.
Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is
Off” displaying on the screen.
30
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote paging operations
Connect the projector to your PC or notebook with a USB cable prior to using the paging
function. See "Connection" on page 15 for details.
You can operate your display software program (on a connected PC) which responds to page
up/down commands (like Microsoft PowerPoint) by pressing PAGE UP/PAGE DOWN on
the remote control.
If remote paging function doesn't work, check if the USB connection is correctly made and
the mouse driver on your computer is updated to the latest version.
The remote paging function cannot work with Microsoft® Windows®98 operating system.
Windows®XP or higher operating systems are recommended.
Freezing the image
Press
Freeze on the remote control to freeze the image. The word “FREEZE” will display
in the upper left corner of the screen. To release the function, press any key on the projector
or remote control.
Even if an image is frozen on the screen, the pictures are running on the video or other
device. If the connected devices have active audio output, you will still hear the audio even
though the image is frozen onscreen.
Hiding the image
In order to draw the audience's full attention to the presenter, you can use BLANK on the
projector or remote control to hide the screen image. The word “BLANK” appears in the
corner of the screen while the image is hidden. When this function is activated with an audio
input connected, the audio can still be heard.
You can set the blank time in the SYSTEM SETUP: Basic > Operation Settings > Blank
Timer menu to let the projector return the image automatically after a period of time when
there is no action taken on the blank screen. The length of time can be set from 5 to 30
minutes in 5-minute increments.
If the preset time spans are not suitable for your presentation, select Disable.
No matter Blank Timer is activated or not, you can press most of the keys on the projector
or remote control to restore the picture.
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Utilizing FAQ function
The INFORMATION menu contains possible solutions to problems regarding image
quality, installation, special feature operation and service information.
To get the FAQ information:
1.
Press
OSD menu and press
Press to select FAQ-Image and Installation or FAQ-Features and Service.
Press MODE/ENTER.
Press to select a problem and press MODE/ENTER for possible solutions.
To exit the OSD menu, press MENU/EXIT.
/
on the projector or remote control or press MENU/EXIT to open the
/
to highlight the INFORMATION menu.
2.
3.
4.
5.
/
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except
POWER.
1.
Press
/
on the projector or remote control or go to the SYSTEM SETUP: Basic >
Panel Key Lock menu, and select On by pressing
control. A confirmation message displays.
/
on the projector or remote
2.
Highlight Yes and press MODE/ENTER to confirm.
To release panel key lock, press and hold
seconds.
/
on the remote control or projector for 3
You can also use the remote control to enter the SYSTEM SETUP: Basic > Panel Key Lock
menu and press to select Off.
/
•
Keys on the remote control are still active when panel key lock is enabled.
•
If you press
POWER to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 m
–3000 m above sea level, and ambient temperature is between 0°C–35°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient
temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode
on under such a condition.
To activate the High Altitude Mode:
1.
2.
3.
Press MENU/EXIT and then press
is highlighted.
/
until the SYSTEM SETUP: Advanced menu
Press to highlight High Altitude Mode and press
message displays.
Highlight Yes and press MODE/ENTER.
/
select On. A confirmation
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Creating your own startup screen
In addition to selecting the projector preset startup screen from among BenQ logo, Black or
Blue screen, you can make your own startup screen that is a picture projected from your
computer or video source.
To create your own startup screen, project the picture you want to use as your startup screen
from either a computer or video source. The rest steps are as follows.
•
Using the remote control
32
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
3.
Press CAPTURE on the remote control.
A confirmation message displays. Press CAPTURE or MODE/ENTER again.
The message 'Screen Capturing...' displays while the projector is processing the
picture. Please wait.
4.
5.
If the action is successful, you see the message 'Captured Succeeded' on the screen. The
captured picture is saved as MyScreen.
To view the captured picture displayed as the startup screen, set MyScreen in the
SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.
Using the OSD menu
•
1.
Press MENU/EXIT and then press
highlighted.
/
until the SYSTEM SETUP: Basic menu is
2.
3.
Press to highlight MyScreen and press MODE/ENTER.
Repeat steps 2-5 in the “Using the remote control” section to capture and view the
captured picture.
In the unlikely event that the capturing action fails, change your target picture.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speakers. Be sure
you have made a correct connection to the projector audio input. See "Connection" on page
15 for how the audio input is connected.
Muting the sound
To temporarily turn off the sound:
1.
2.
3.
Press MENU/EXIT and then press
is highlighted.
/
until the SYSTEM SETUP: Advanced menu
Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings
page displays.
Highlight Mute and press
/
to select On.
Adjusting the sound level
To adjust the sound level, press VOLUME+/VOLUME- on the remote control, or:
1.
2.
Repeat steps 1-2 above.
Press to highlight Volume and press
/
to select a desired sound level.
Turning off the Power On/Off Ring Tone
To turn off the ring tone:
1.
2.
Repeat steps 1-2 above.
Press to highlight Power On/Off Ring Tone and press
/
to select Off.
The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power On/Off Ring Tone.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Controlling the projector through a LAN
environment
You can manage and control the projector from a remote computer when they are properly
connected to the same local area network.
Wireless connection
To connect to the projector wirelessly, you have to plug a BenQ wireless dongle (optional) to
the USB Type A connector on the projector, and then only a few OSD configuration steps are
required.
1.
2.
Make sure the projector is turned on.
Press MENU/EXIT and then press
is highlighted.
/
until the SYSTEM SETUP: Advanced menu
3.
4.
5.
Press to highlight Wireless LAN and press MODE/ENTER.
Make sure the Status is Connect.
Make sure the SSID information is displayed.
There are more wireless settings available on the Projector Network display System > Admin >
Wireless LAN page.
Controlling the projector remotely through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby
mode, you can use any computer that is on the same local area network to control the
projector.
•
•
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
The screenshots in this manual are for reference only, and may differ from the actual
design.
1.
Enter the address of the projector in the address bar of your browser and press Enter.
34
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
The main page of the Projector Network Display System appears. This web page
provides access to a variety of functions with a simple click.
3.
4.
Click Download to save Q Presenter software on your computer. See "Displaying
images through Q Presenter" on page 39 for details.
The Virtual Keypad page displays a virtual keypad with which you can control the
projector as if using the physical keypad on the projector. See "Projector" on page 10
for how to operate it.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
35
5.
The Display Setting page provides some selective OSD menu items necessary for
controlling the projector or adjusting the projected pictures. See the chapter "Menu
operation" for how to use them.
6.
The Picture Setting page provides all the OSD menu items in the PICTURE menu for
adjusting the projected pictures. See "2. PICTURE menu" on page 48 for how to use
them.
36
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
The Information page displays the information about the projector status, network
status.
8.
To have access to the Admin page, you need to enter a password. The page provides
more network settings. The default password is “0000”. If you want to change the
password, enter the Basic page.
Operation
37
Download from Www.Somanuals.com. All Manuals Search And Download.
The Basic page allows you to change the password and set the maximum number of
connected computers. The number of connected computer may affect the network
display performance.
The Wireless LAN page allows you to adjust the Wireless LAN settings.
The maximum length for SSID is 16 bytes. Please use different SSID when more
than two projectors are connecting through wireless LAN.
9.
These quick buttons are always provided on the web page for you to operate the
projector.
38
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying images through Q Presenter
Downloading and installing Q Presenter
Q Presenter is an application running on the host PC. It helps connect your computer to an
available network projector and transfer the desktop contents to the network projector via
local network connection.
1.
Enter the main page of the Projector Network Display System. See steps 1-2 on page 34
for details.
2.
3.
Click the Download icon.
When the download is complete, install the software to your computer by clicking the
exe file. Follow the on-screen instructions to complete the installation.
Launch Q Presenter.
4.
Using Q Presenter
1
2
3
5
&
4
1.
The Search page allows you to search and connect to a projector.
•
•
To connect to a projector, type the projector IP address and click Connect.
To search for projectors, simply click Search to list all the projectors on the same
local area network. Click the desired projectors in the Search result list, and click
Connect. You can also type a desired projector name and click Search.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
39
2.
The Special Feature page provides some advanced functions to manage the projected
images.
•
•
To display a full screen, click Full Screen.
To display a partial screen, click Selectable. A square appears on your screen. You
can adjust its size and place it where you want to project.
•
To pause projection, click Pause.
3.
The Basic Settings page allows you to configure Q Presenter.
•
•
To change the Q Presenter interface language, click the down arrow to reveal a
drop-down list and select a desired language. Click Apply.
To allow notification messages to appear, click Yes. Click Apply.
40
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
The Advanced Settings page allows you to configure Q Presenter.
•
To display still pictures, click the down arrow to reveal a drop-down list and
select Graphic. Click Apply. To display video clips, click the down arrow to reveal
a drop-down list and select Video. Click Apply.
Graphic mode: worse image quality but faster transmission speed.
Video mode: better image quality but slower transmission speed.
However, the actual transmission speed was determined by the network traffic at
that time.
•
•
•
To adjust the capture rate, move the slider. The network bandwidth may also
affect the performance.
To launch Q Presenter when your computer operating system is started, click Yes
for Boot and launch. Click Apply.
To link to the Projector Network Display System web page, click Link.
5.
Disconnect
To disconnect from the projector(s), click the Disconnect icon.
Be sure to turn off other virtual network control programs before using Q Presenter.
•
•
•
Firewall in the PC must be switched off to allow Q Presenter and USB Display to work.
Wireless keyboard mouse combo is not supported by Pixelworks currently.
Operation
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Presenting from a USB Reader
This feature displays a slide show of images stored on a USB flash drive connected to the
projector. It can eliminate the need for a computer source.
Supported image formats:
•
•
JPEG(JPG)
BMP
•
•
PNG
GIF
•
TIFF
•
•
•
A square box will display on the filename for unidentified characters.
Thai filename is not supported.
Files in GIF, TIFF, PNG and BMP formats can be displayed for the file size smaller than
WXGA (1280 x 800) only.
•
If a folder consists of more than 200 photos, only the first 200 photos can be displayed.
To view your pictures as a slide show, follow these steps:
1.
2.
Plug the USB flash drive into the USB TYPE-A jack of the projector.
The projector automatically displays the thumbnails. Or you can manually select USB
Reader from the source selection bar.
When viewing thumbnails
To
Press
open the folder
Enter
scroll through thumbnails
return to a previous page
exit USB Reader
change to a different page
four arrow keys
Auto
Exit
/
go back to the first page of that folder Back
start a slide show
Slideshow when an image is highlighted.
adjust USB Reader settings
Setting
During a slide show
To
Press
go to the previous or next image
/
/
rotate the image by 90 degree
clockwise/counterclockwise
(Rotation is temporary; the image returns
to its original orientation when you go
back to thumbnails)
return to a previous page
start/stop a slide show
Auto
Enter
Setting page
You can adjust the file order and Slideshow settings. When you are done, press OK to save
the settings or press Cancel to ignore the change.
42
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutting down the projector
1.
Press
If you don't respond in a few seconds, the message will disappear.
POWER and a confirmation message will display prompting you.
2.
projection lamp shuts down, and the fans will continue to run for approximately 90
seconds to cool down the projector.
To protect the lamp, the projector will not respond to any commands during the cooling
process.
To shorten the cooling time, you can also activate the Quick cooling function. See "Quick
Cooling" on page 50 for details.
3.
Once the cooling process finishes, a "Power Off Ring
Tone" will be heard. The POWER indicator light is a
steady orange and fans stop. Disconnect the power
cord from the power outlet.
•
•
To turn off the power ring tone, see "Turning off the
Power On/Off Ring Tone" on page 33 for details.
If the projector is not properly shut down, to protect the
lamp, when you attempt to re-start the projector, the fans
will run for a few minutes to cool down. Press
POWER
again to start the projector after the fans stop and the
POWER indicator light turns orange.
•
Lamp life results will vary depending on environmental
conditions and usage.
Direct power off
The AC power cord can be pulled out right after the projector is turned off. To protect the
lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start
the projector, the fans may run for a few minutes to cool down. In such cases, press
I
POWER again to start the projector after the fans stop and the POWER indicator light
turns orange.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected and the projector model you are using.
Main menu Sub-menu
Options
Off/Light Yellow/Pink/Light
Green/Blue/Blackboard
Auto/Real/4:3/16:9/16:10
Wall Color
Aspect Ratio
Keystone
Position
Phase
1.
H. Size
Digital Zoom
3D Sync
DISPLAY
On/Off
3D Sync Invert
Disable/Invert
Off/Letter Formation/Worksheet/
Coordinate Chart
Blackboard
Whiteboard
Teaching
Template
Off/Letter Formation/Worksheet/
Coordinate Chart
Picture Mode
Dynamic/Presentation/sRGB/Cinema/User 1/User 2
Reference Mode Dynamic/Presentation/sRGB/Cinema
Brightness
Contrast
Color
Tint
2.
Sharpness
Brilliant Color
On/Off
PICTURE
Color Temperature
T1/T2/T3/T4
Primary Color R/G/B/C/M/Y
Hue
3D Color
Management
Saturation
Gain
Save Settings
Quick Auto Search
On/Off
3. SOURCE
Color Space Conversion
Auto/RGB/YUV
Timer Period
1~240 minutes
Timer Display
Always/1 min/2 min/3 min/Never
Top-Left/Bottom-Left/Top-Right/
Bottom-Right
4.
Timer Position
SYSTEM
SETUP:
Basic
Presentation
Timer
Timer Counting
Direction
Sound
Reminder
On/Off
Count Down/Count Up
On/Off
44
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Main menu Sub-menu
Options
Language
Front Table/Rear Table/Rear
Ceiling/Front Ceiling
Projector Position
Menu Display
5 sec/10 sec/15 sec/20 sec/25
sec/30 sec
Time
Center/Top-Left/Top-Right/
Bottom-Right/Bottom-Left
4.
Menu Settings Menu Position
SYSTEM
SETUP:
Basic
Reminder
Message
On/Off
Direct Power On On/Off
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Auto Power Off
Operation
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Settings
Blank Timer
Disable/30 min/1 hr/2 hr/3 hr/4
hr/8 hr/12 hr
Sleep Timer
Remote Receiver
Panel Key Lock
Front+Top/Top/Front
On/Off
Background Color
Splash Screen
My Screen
Black/Blue/Purple/BenQ
Black/Blue/BenQ/MyScreen
Quick Cooling
High Altitude Mode
On/Off
On/Off
On/Off
Mute
Volume
Audio Settings
Power On/Off
Ring Tone
Lamp Mode
On/Off
5.
Normal/Economic
SYSTEM
SETUP:
Advanced
Lamp Settings Reset lamp timer
Equivalent Lamp Hour
Change
Password
Security
Settings
Power On Lock
Change Security
Settings
Splash Screen Lock
2400/4800/9600/14400/19200/
38400/57600/115200
On/Off
Baud Rate
Test Pattern
Operation
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Main menu Sub-menu
Options
Closed Caption
Enable
On/Off
Closed Caption
Caption Version CC1/CC2/CC3/CC4
5.
Network
On/Off
On/Off
Standby
Settings
Monitor Out
Status
SYSTEM
SETUP:
Advanced
SSID
Wireless LAN
IP Address
Connection Mode
Reset All Settings
FAQ-Image and Installation
FAQ-Features and Service
• Source
6.
• Picture Mode
• Resolution
• Color System
• Equivalent Lamp Hour
• Firmware Version
INFORMATION
Current System Status
Note that the menu items are available when the projector detects at least one valid signal. If
there is no equipment connected to the projector or no signal detected, limited menu items
are accessible.
46
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of each menu
Function
Description
Corrects the projected picture’s color when the projection surface is not
white. See "Using Wall Color" on page 27 for details.
Wall Color
Aspect Ratio
Keystone
There are several options to set the image's aspect ratio depending on
your input signal source. See "Selecting the aspect ratio" on page 25 for
details.
Corrects any keystoning of the image. See "Switching input signal" on
page 24 for details.
Displays the position adjustment page. To move the projected image,
use the directional arrow keys. The values shown on the lower position
of the page change with every key press you made until they reach their
maximum or minimum.
Position
Phase
selected.
Adjusts the clock phase to reduce image
distortion.
This function is only available when a PC
signal (analog RGB) is selected.
Adjusts the horizontal width of the image.
H. Size
This function is only available when a PC signal (analog RGB) is
selected.
Magnifies or reduces the projected image. See "Magnifying and
searching for details" on page 25 for details.
Digital Zoom
This projector features a 3D function which enables you to enjoy the
3D movies, videos, and sporting events in a more realistic way by
presenting the depth of the images. You need to wear a pair of 3D
glasses to view the 3D images.
•
For a PC type signal:
When the vertical frequency is 60Hz or 120Hz, and the content being
projected is made with 3D technology, selecting On will present the 3D
images.
3D Sync
•
For a video type signal:
When the content being projected is made with 3D technology,
selecting On will present the 3D images.
When the 3D Sync function is On:
• The brightness level of the projected image will decrease.
• The Picture Mode cannot be adjusted.
• The Keystone can only be adjusted within limited degrees.
3D Sync
Invert
When you discover the inversion of the image depth, enable this
function to correct the problem.
Operation
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Description
Provides several preset patterns for various teaching purposes.
Teaching
Template
Choose Blackboard or Whiteboard first by pressing
the pattern.
/
and press
/
Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type. See "Selecting a
picture mode" on page 27 for details.
Picture Mode
Selects a picture mode that best suits your need for the image quality
same page below. See "Setting the User 1/User 2 mode" on page 27 for
details.
Reference
Mode
Adjusts the brightness of the image. See "Adjusting Brightness" on page
28 for details.
Brightness
Contrast
Adjusts the degree of difference between dark and light in the image.
See "Adjusting Contrast" on page 28 for details.
Adjusts the color saturation level -- the amount of each color in a video
Color
Tint
This function is only available when a Video, S-Video or
Component Video signal is selected.
Adjusts the red and green color tones of the image. See "Adjusting Tint"
on page 28 for details.
This function is only available when a Video or S-Video signal is
selected and the system format is NTSC.
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 28 for details.
Sharpness
This function is only available when a Video, S-Video or
Component Video signal is selected.
See "Adjusting Brilliant Color" on page 28 for details.
Brilliant Color
Color
Temperature
There are four color temperature settings available. See "Selecting a
color temperature" on page 28 for details.
3D Color
Management
See "3D Color Management" on page 29 for details.
Saves the settings made for User 1 or User 2 mode.
Save Settings
48
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Description
Quick Auto
Search
See "Switching input signal" on page 24 for details.
Color Space
Conversion
See "Changing Color Space" on page 24 for details.
Presentation
Timer
Reminds the presenter to finish the presentation within a certain time
frame. See "Setting the presentation timer" on page 30 for details.
Sets the language for the On-Screen Display (OSD) menus. See "Using
the menus" on page 20 for details.
Language
Projector
Position
The projector can be installed on a ceiling or behind a screen, or with
one or more mirrors. See "Choosing a location" on page 13 for details.
Menu Display Time
Sets the length of time the OSD will remain active after your last key
Menu
Settings
Menu Position
Sets the On-Screen Display (OSD) menu position.
Reminder Message
Sets the reminder messages on or off.
Direct Power On
Allows the projector to turn on automatically once the power is fed
through the power cord.
Auto Power Off
Allows the projector to turn off automatically if no input signal is
detected after a set period of time. See "Setting Auto Power Off" on page
54 for details.
Operation
Settings
Blank Timer
Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen. See "Hiding the image" on
page 31 for details.
Sleep Timer
Sets the auto-shutdown timer. The timer can be set to a value between
30 minutes and 12 hours.
Remote
Receiver
Allows you to enable all the remote receivers or one specific remote
receiver on the projector.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Function
Disables or enables all panel key functions except
projector and keys on the remote control. See "Locking control keys" on
page 32 for details.
POWER on the
Panel Key
Lock
Background
Color
Sets the background color for the projector.
start-up. The following options are available: BenQ logo, My Screen,
Black screen, Blue screen.
Splash
Screen
Captures and stores the projected picture as My Screen. See "Creating
your own startup screen" on page 32 for details.
My Screen
In the unlikely event that the capturing action fails, change your
target picture.
the function and projector cooling time will be shortened from a normal
90-second duration to approximately 30 seconds.
Quick
Cooling
High
Altitude
Mode
A mode for operation in high altitude areas. See "Operating in a high
altitude environment" on page 32 for details.
Mute
Audio
Volume
Settings
Power On/Off Ring Tone
See "Adjusting the sound" on page 33 for details.
Lamp Mode
See "Setting Lamp Mode as Economic" on page 54 for details.
Reset lamp timer
See "Resetting the lamp timer" on page 58 for details.
Lamp
Settings
Equivalent Lamp Hour
See "Getting to know the lamp hour" on page 54 for details on how the
total lamp hour is calculated.
Change Password
You will be asked to enter the current password before changing to a new
one. See "Utilizing the password function" on page 21 for details.
Security
Settings
Change Security Settings
Power On Lock
Splash Screen Lock
See "Utilizing the password function" on page 21 for details.
50
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Description
Selects a baud rate that is identical with your computer’s so that you can
connect the projector using a suitable RS-232 cable and update or
download the projector’s firmware. This function is intended for
qualified service personnel.
Baud Rate
Selecting On enables the function and the projector displays the grid test
pattern. It helps you adjust the image size and focus and check that the
projected image is free from distortion.
Test Pattern
Closed Caption Enable
Activates the function by selecting On when the selected input signal
carries closed captions.
•
Captions: An on-screen display of the dialogue, narration, and
sound effects of TV programs and videos that are closed captioned
(usually marked as "CC" in TV listings).
Closed
Caption
Set your screen aspect ratio to 4:3. This function is not available
when the aspect ratio is “16:9” or “Real”.
Caption Version
Selects a preferred closed captioning mode. To view captions, select
CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language
in your area).
Network
Selecting On enables the function. The projector is able to provide the
network function when it is in standby mode.
Monitor Out
Selecting On enables the function. The projector can output a VGA
signal when it is in standby mode and the COMPUTER 1 jack is
correctly connected to devices. See "Connection" on page 15 for how to
make the connection.
Standby
Settings
Enabling this function slightly increases the standby power
consumption.
See "Controlling the projector through a LAN environment" on page 34
for details.
Wireless
LAN
Returns all settings to the factory preset values.
Reset All
Settings
The following settings will still remain: Phase, H. Size, User 1, User
2, Color Space Conversion, Language, Projector Position, High
Altitude Mode, Security Settings, SSID and Baud Rate.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Function
Description
FAQ-Image
and
Installation
Displays possible solutions to problems you may encounter.
FAQ-
Featuresand
Service
Source
Shows the current signal source.
Picture Mode
Shows the selected mode in the PICTURE menu.
Resolution
Current
System
Status
Shows the native resolution of the input signal.
Color System
Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
Firmware Version
Shows the firmware version of your projector.
52
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens and case clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner
and gently wipe the lens surface.
•
Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile
solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or
maintaining prolonged contact with rubber or vinyl materials may result in damage to
the projector surface and cabinet material.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 43 and unplug the power cord.
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 61 or
consult your dealer about the range.
•
•
•
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. When
you carry the projector yourself, please use the original box or provided soft carry case.
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
See "Setting Lamp Mode as Economic" below for more information on Economic mode.
To obtain the lamp hour information:
1.
Press MENU/EXIT and then press
menu.
/
to highlight the SYSTEM SETUP: Advanced
2.
Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page
displays.
3.
4.
You will see the Equivalent Lamp Hour information displaying on the menu.
To leave the menu, press MENU/EXIT.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item that normally can last up to 3000-4000 hours
with proper usage. To keep the lamp life as long as possible, you can do the following settings
via the OSD menu.
•
Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp Mode
menu and press
/
.
•
Setting Auto Power Off
This function allows the projector to turn off automatically if no input signal is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Operation Settings > Auto
Power Off menu and press
/
. The time period can be set from 5 to 30 minutes in 5-
minute increments. If the preset time lengths are not suitable for your presentation, select
Disable. The projector will not automatically shut down in a certain time period.
54
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
page 59 for details.
The following Lamp warning displays will remind you to change the lamp.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
(See "Getting to know the lamp hour" on page 54),
you may continue to operate the projector until
the next hour lamp warning appears.
Notice
Order Replacement Lamp
Lamp>XXXX Hours
Order a new lamp at lamp.benq.com
Press MODE/ENTER to dismiss the message.
OK
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
Notice
Order Replacement Lamp
Lamp>XXXX Hours
Order a new lamp at lamp.benq.com
Press MODE/ENTER to dismiss the message.
OK
The lamp MUST be replaced before the projector
will operate normally.
WARNING
Out of Lamp Usage Time
Press MODE/ENTER to dismiss the message.
Replace lamp (refer to User Manual)
Then reset lamp timer
Order a new lamp at lamp.benq.com
OK
"XXXX" shown in the above messages are numbers that vary depending on different models.
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Replacing the lamp
•
•
•
•
•
•
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
To reduce the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of
this lamp in a proper manner.
To assure optimal performance from the projector, it is recommended that you purchase a
qualified projector lamp for lamp replacement.
If lamp replacement is performed while the projector is suspended upside-down from the
ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury
or damage to the human eyes caused by fractured lamp.
1.
Turn the power off and disconnect the projector from the power outlet. If the lamp is
hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
Loosen the screw that secures the lamp
2.
cover on the side of the projector until the
lamp cover loosens.
3.
•
Remove the lamp cover from the
projector.
1
Do not turn the power on with the lamp cover
removed.
1
•
Do not insert your fingers between the lamp
and the projector. The sharp edges inside the
projector may cause injuries.
4.
5.
6.
Remove and dispose the protection film.
Loosen the screw that secures the lamp.
Lift the handle so that it stands up.
1
2
56
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
•
Use the handle to slowly pull the lamp out of
the projector.
Pulling it too quickly may cause the lamp to break
and scatter broken glass in the projector.
•
Do not place the lamp in locations where water
might splash on it, children can reach it, or near
flammable materials.
•
Do not insert your hands into the projector after
the lamp is removed. If you touch the optical
components inside, it could cause color
unevenness and distortion of the projected
images.
8.
As shown in the figure, lower the new lamp.
9.
Tighten the screw that secures the lamp.
2
10. Ensure the handle is fully laid flat and locked
in place.
•
Loose screw may cause a bad connection, which
could result in malfunction.
1
•
Do not over tighten the screw.
11. Replace the new protection film that comes
with the new lamp.
2
12. Replace the lamp cover on the projector.
2
13. Tighten the screw that secures the lamp cover.
•
Loose screw may cause a bad connection, which
could result in malfunction.
•
Do not over tighten the screw.
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
57
14. Connect the power and restart the projector.
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
15. After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM
SETUP: Advanced > Lamp Settings menu. Press MODE/ENTER. The Lamp Settings
page displays. Highlight Reset lamp timer. A warning message displays asking if you
want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp
time will be reset to “0”.
Do not reset if the lamp is not new or replaced as this could cause damage.
58
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicators
Light
Status & Description
Power events
Orange
Off
Off
Off
Off
Stand-by mode.
Green
Flashing
Off
Off
Powering up.
Green
Normal operation.
•
The projector needs 90 seconds to cool down as it was
abnormally shut down without the normal cooling down
process.
•
•
The projector needs to cool for 90 seconds after the power
is turned off.
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact
your dealer for assistance.
Orange
Flashing
Off
Off
Lamp events
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact your
dealer for assistance.
Orange
Flashing
Off
Off
Red
Red
1.
2.
The projector needs 90 seconds to cool down. Or
Please contact your dealer for assistance.
Off
Thermal events
Off
Off
Red
Red
Red
Red
Red
Red
Red
Red
Red
Red
Red
Red
Red
Green
Green
Off
Red
Off
Green
Orange
Red
Off
Red
Red
Green
Orange
Red
Red
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact your
dealer for assistance.
Green
Green
Green
Orange
Orange
Orange
Off
Green
Orange
Red
Green
Orange
Red
Off
Green
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the power cord into the AC power jack on
the projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
There is no power from the power
cord.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input signal device.
Check the connection.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The input signal has not been
correctly selected.
The lens cover is still closed.
Blurred image
Open the lens cover.
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the projector if necessary.
Open the lens cover.
The lens cover is still closed.
Remote control does not work
Cause
Remedy
The battery is out of power.
There is an obstacle between the
remote control and the projector.
You are too far away from the
projector.
Replace the battery with new ones.
Remove the obstacle.
Stand within 8 meters (26 feet) of the
projector.
The password is incorrect
Cause
Remedy
Please see "Entering the password recall
procedure" on page 22 for details.
You do not remember the password.
60
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Control
Resolution
RS-232 serial control
(MX660/MX615)
1024 x 768 XGA
(MS614)
9 pin x 1
IR receiver x 2
800 x 600 SVGA
Input terminals
Display system
1-CHIP DMD
Computer input
RGB input
Lens F/Number
F = 2.56-2.8
Lamp
D-Sub 15-pin (female) x 2
Video signal input
S-VIDEO
(MX660)
Mini DIN 4-pin port x 1
VIDEO
RCA jack x 1
230 W lamp
(MX615/MS614)
210 W lamp
SD/HDTV signal input
Analog - Component RCA jack x 3
(through RGB input)
Electrical
Power supply
Digital - HDMI V1.3 x 1
(MX660)
Audio signal input
Audio in
AC100–240V, 3.8 A, 50-60 Hz (Automatic)
(MX615/MS614)
AC100–240V, 3.8 A, 50-60 Hz (Automatic)
Power consumption
PC audio jack x 1
RCA audio jack (L/R) x 2
USB ports (Type-A x 1; Mini-B x 1)
(MX660)
339 W (Max); < 1 W (Standby)
(MX615/MS614)
Environmental Requirements
326 W (Max); < 1 W (Standby)
Operating temperature
0°C–40°C at sea level
Mechanical
Operating relative humidity
10%–90% (without condensation)
Weight
2.65 Kg (5.84 lbs)
Operating altitude
0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with
High Altitude Mode on)
Output terminals
RGB output
D-Sub 15-pin (female) x 1
Speaker
(Stereo) 2 watt x 1
Audio signal output
PC audio jack x 1
Specifications
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing chart
Supported timing for PC input
Pixel
Frequency
(MHz)
Vertical
Horizontal
Resolution
Mode
Frequency (Hz) Frequency (kHz)
VGA_60*
VGA_72
VGA_75
VGA_85
VGA_70
SVGA_60*
SVGA_72
SVGA_75
SVGA_85
XGA_60*
XGA_70
59.940
72.809
75.000
85.008
70.087
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
60.0
64.995
59.810
74.934
84.880
60.020
75.025
85.024
60.000
85.005
59.887
59.978
60.000
66.667
74.546
75.020
75.060
119.518
119.854
119.989
31.469
37.861
37.500
43.269
31.469
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.667
35.820
41.467
49.702
62.795
71.554
63.981
79.976
91.146
60.000
85.938
55.935
65.317
75.000
35.000
49.722
60.241
68.680
61.910
77.425
97.551
25.175
31.500
31.500
36.000
28.3221
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
46.966
51.419
83.500
106.500
122.500
108.000
135.000
157.500
108.000
148.500
106.500
121.750
162.000
30.240
57.280
80.000
100.000
52.500
83.000
115.5
640 x 480
720 x 400
800 x 600
1024 x 768
XGA_75
XGA_85
BenQ
BenQ
1024 x 576
1024 x 600
WXGA_60*
WXGA_75
WXGA_85
SXGA_60*
SXGA_75
SXGA_85
1280 x 960_60*
1280 x 960_85
WXGA+_60*
SXGA+_60*
UXGA
MAC13
MAC16
MAC19
MAC21
VGA_120*
SVGA_120*
XGA_120*
1280 x 800
1280 x 1024
1280 x 960
1440 x 900
1400 x 1050
1600 x 1200
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
640 x 480
800 x 600
1024 x 768
*Supported timing for 3D function.
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Supported timing for HDMI (HDCP) input
Pixel
Frequency
(MHz)
Vertical
Horizontal
Resolution
Mode
Frequency (Hz) Frequency (kHz)
VGA_60*
VGA_72
VGA_75
VGA_85
VGA_70
SVGA_56
SVGA_60*
SVGA_72
SVGA_75
SVGA_85
XGA_60*
59.940
72.809
75.000
85.008
70.087
56.250
60.317
72.188
75.000
85.061
60.000
59.870
74.893
84.837
59.810
74.934
84.880
60.020
75.025
85.024
60.000
85.002
60.015
60
59.887
74.984
84.842
59.978
60.000
59.883
59.954
66.667
74.546
75.020
75.060
60.0
31.469
37.861
37.500
43.269
31.469
35.156
37.879
48.077
46.875
53.674
47.396
47.776
60.289
68.633
49.702
62.795
71.554
63.981
79.976
91.146
60.000
85.938
47.712
55.469
55.935
70.635
80.430
65.317
75.000
64.674
65.290
35.000
49.722
60.241
68.680
35.820
41.467
61.910
77.425
97.551
25.175
31.500
31.500
36.000
28.3221
36.000
40.000
50.000
49.500
56.250
68.25
640 x 480
640 x 480
800 x 600
XGA_60*
XGA_75
XGA_85
79.5
1024 x 768
102.25
117.50
83.500
106.500
122.500
108.000
135.000
157.500
108.000
148.500
85.500
88.75
106.500
136.750
157.000
121.750
162.000
119.000
146.250
30.240
57.280
80.000
100.000
46.996
51.419
52.500
83.000
115.5
WXGA_60*
WXGA_75
WXGA_85
SXGA_60*
SXGA_75
SXGA_85
1280 x 960_60*
1280 x 960_85
1360 x 768_60*
WXGA+_60*
WXGA+_60*
WXGA+_75
WXGA+_85
SXGA+_60*
UXGA
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1440 x 900
1400 x 1050
1600 x 1200
1680 x 1050
1680 x 1050_60
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
1024 x 576
MAC13
MAC16
MAC19
MAC21
Netbook_timing*
Netbook_timing
VGA_120*
SVGA_120*
XGA_120*
1024 x 600
640 x 480
800 x 600
1024 x 768
64.995
119.518
119.854
119.989
*Supported timing for 3D function.
64
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical
Horizontal
Pixel
Frequency
(MHz)
Timing
Resolution Frequency Frequency
Remark
(Hz)
59.94
59.94
50
(kHz)
15.73
31.47
15.63
720(1440) x
480
720 x 480
720(1440) x
576
480i*
480p
576i
27
27
27
HDMI only
HDMI only
HDMI/DVI
576p
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
50
50
60
50
60
50
60
31.25
37.5
27
HDMI/DVI
HDMI/DVI
HDMI/DVI
HDMI/DVI
HDMI/DVI
HDMI/DVI
HDMI/DVI
720/50p
720/60p
1080/50i
1080/60i
1080/50P
1080/60P
74.25
74.25
74.25
74.25
148.5
148.5
45.00
28.13
33.75
56.25
67.5
•
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
•
*Supported timing for 3D function.
Supported timing for Component-YPbPr input
Vertical
Horizontal
Pixel Frequency
(MHz)
13.5
Timing
Resolution
Frequency (Hz) Frequency (kHz)
480i*
480p
576i
720 x 480
720 x 480
720 x 576
59.94
59.94
50
50
50
60
50
60
50
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
56.25
67.5
27
13.5
27
74.25
74.25
74.25
74.25
148.5
148.5
576p
720 x 576
720/50p
720/60p
1080/50i
1080/60i
1080/50P
1080/60P
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
60
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
Supported timing for Video and S-Video inputs
Horizontal
Frequency (kHz)
15.73
Vertical Frequency Color sub-carrier
Video mode
(Hz)
60
Frequency (MHz)
NTSC*
PAL
3.58
4.43
15.63
50
SECAM
PAL-M
15.63
15.73
50
60
4.25 or 4.41
3.58
PAL-N
15.63
50
3.58
PAL-60
NTSC4.43*
15.73
15.73
60
60
4.43
4.43
*Supported timing for 3D function.
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal
usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is
found to be defective within the warranty period, BenQ's only obligation and your exclusive
remedy shall be replacement of any defective parts (labor included). To obtain warranty
service, immediately notify the dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be in-
between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
Copyright
Copyright 2010 by BenQ Corporation. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any
language or computer language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior written permission of
BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties, merchantability
or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise
this publication and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
Patents
This BenQ projector is covered by the following patents:
U.S. patents 6,837,608; 7,275,834; 7,181,318. TW patents 202690; 205470; I228635; I259932.
China patents ( 中国发明专利 ) ZL01143168.7; ZL03119907.0; ZL200510051609.2
66
Warranty and Copyright information
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulation statements
FCC statement (for United States users)
CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
EEC statement (for European users)
This device complies with the requirements set out in the Council Directives on the
Approximation of the Laws of the Member States relating Electromagnetic Compatibility
(2004/108/EC), Low Voltage Directive (2006/95/EC), the Restriction of The Use of Certain
Hazardous Substances in Electrical And Electronic Equipment Directive (2002/95/EC),
Turkish EEE Directive, Commission Regulation (EC) No 1275/2008 implementing Directive
2005/32/EC of the European Parliament and of the Council with regard to ecodesign
requirements for standby and off mode electric power consumption of electrical and
electronic household and office equipment, and the Directive 2009/125/EC of the European
parliament and of the council establishing a framework for the setting of ecodesign
requirements for energy-related products.
WEEE directive
Disposal of Waste Electrical and Electronic Equipment by users in private households in the
European Union.
This symbol on the product or on the packaging indicates that this can not
be disposed of as household waste. You must dispose of your waste
equipment by handing it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment. For more information
about recycling of this equipment, please contact your city office, the shop
where you purchased the equipment or your household waste disposal
service. The recycling of materials will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and
environment.
Regulation statements
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessibility Requirements for Rehabilitation Act of 1973, Section
508
BenQ's commitment to accessible products allows us to support government in making
accessible technology choices. BenQ's LCD monitors and projectors are compliant with
Section 508 guidelines by including the assistive features as below:
•
•
•
BenQ's monitors have colored "Power" indicators. While the indicator shows green, it
means that the monitor is using the full power. While the indicator shows yellow or
amber, it means that the monitor is in suspend or sleep mode and is using less than 2
watts of electricity.
BenQ's monitors have a variety of settings of pre-programmed flicker-free timing to
make the screen shown on the monitor readily accessible. The default timing setting is
automatically turned on every time the monitor is powered up, and thus reduces the
hassle of user intervention.
BenQ's monitors and projectors have options for brightness and contrast adjustments
that text and images could be displayed differently to meet the demands of the visually
impaired. Other similar adjustments are also available by using the On-Screen Display
(OSD) controls on the products.
•
•
•
•
•
•
BenQ's monitors and projectors include user-selectable color controls, such as color
temperature selections (Monitor: 5800K, 6500K and 9300K, Projector: 5500K, 6500K,
7500K and 9300K), with a wide range of contrast levels.
BenQ's multimedia monitors and projectors usually have one or two speakers for audio
performance which allow users (including hearing impaired) to interact with the
computer systems connected. Speaker controls are typically located on the front-panel.
Firmware of BenQ's monitors and projectors contain unique product information that
helps computer systems to identify BenQ products and activate their Plug-and-Play
function when connected.
All BenQ's monitors and projectors are compatible with the PC99 standard. For
example, connectors are color-coded to help users easily connecting products to
computer systems correctly.
Some models of BenQ's monitors and projectors contain additional USB and DVI ports
for connection to more devices such as a special headphone to assist the hearing
impaired.
All BenQ monitors and projectors come with user manuals on compact discs which
could be easily read by commercial software such as Adobe Reader via a connected
computer system. These documents are also available on the BenQ's web site
BenQ's customer service provides answers and assistance to all our customers through
phone calls, facsimiles, e-mails, or web sites.
•
68
Regulation statements
Download from Www.Somanuals.com. All Manuals Search And Download.
|