3000PSI
Pressure Washer Owner’s Manual
Generac Portable Products is a licensed trademark of Briggs & Stratton Power Products.
Questions? Help is just a moment away!
Call: Generac Pressure Washer Helpline - 1-800-270-1408 M-F 8-5 CT
Model No. 1418-2 (3,000 PSI Pressure Washer) Manual No. 191658GS Revision 1 (03/05/2003)
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
WARNING
DANGER
Fuel and its vapors are extremely flammable and
explosive.
Running engine gives off carbon monoxide, an
odorless, colorless, poison gas.
Fire or explosion can cause severe burns or
death.
Some chemicals or detergents may be harmful if
inhaled or ingested, causing severe nausea,
fainting or poisoning.
Breathing carbon monoxide will cause nausea,
fainting or death.
WHEN ADDING FUEL
• Turn pressure washer OFF and let it cool at least 2 minutes
before removing gas cap.
• Operate pressure washer ONLY outdoors.
• Use a respirator or mask whenever there is a chance that
vapors may be inhaled.
• Fill fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
• Read all instructions with mask so you are certain the mask will
provide the necessary protection against inhaling harmful vapors.
• DO NOT light a cigarette or smoke.
WARNING
Spray contact with electrical wiring can result in
electrocution.
WHEN OPERATING EQUIPMENT
• DO NOT tip engine or equipment at angle which causes fuel
to spill.
• DO NOT spray flammable liquids.
• Keep water spray away from electric wiring or fatal electric
shock may result.
WHEN TRANSPORTING OR REPAIRING EQUIPMENT
• Transport/repair with fuel tank EMPTY or with fuel shutoff
valve OFF.
WARNING
WHEN STORING FUEL OR EQUIPMENT WITH FUEL
IN TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they can ignite fuel vapors.
Use of pressure washer can create puddles and
slippery surfaces.
High pressure spray could cause you to fall if
you are too close to the cleaning surface.
WARNING
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury and
possible amputation.
• Keep spray nozzle between 8 to 24 inches away from cleaning
surface.
• Operate this unit on a stable surface.
• The cleaning area should have adequate slopes and drainage to
reduce the possibility of a fall due to slippery surfaces.
• Be extremely careful if you must use the pressure washer from
a ladder, scaffolding or any other relatively unstable location.
• NEVER aim spray gun at people, animals or plants.
• DO NOT allow CHILDREN to operate pressure washer.
• NEVER repair high pressure hose. Replace it.
• Keep high pressure hose connected to pump and spray gun
while system is pressurized.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury if gun kicks back.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
WARNING
CAUTION
Excessively high or low operating speeds increase risk
of injury and damage to pressure washer.
Running engines produce heat and hot exhaust
gases. Temperature of muffler and nearby areas
can reach or exceed 150°F (65°C).
• DO NOT tamper with governed speed.
Fire or severe burns can occur.
• DO NOT operate pressure washer above rated pressure.
• DO NOT touch hot surfaces.
CAUTION
• Stay clear of exhaust gases.
A pressure washer produces a high pressure spray
which increases risk of injury and damage to unit.
• Allow equipment to cool before touching.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
WARNING
• NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working order.
Starter and other rotating parts can entangle
hands, hair, clothing, or accessories.
• Always be certain spray gun, nozzles and accessories are
correctly attached.
• DO NOT wear loose clothing, jewelry or anything that may
be caught in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
CAUTION
High pressure spray may damage fragile items including
glass.
• DO NOT point spray gun at glass when in jet spray mode.
• NEVER aim spray gun at plants.
WARNING
CAUTION
Improper treatment of pressure washer can damage it
and shorten its life.
High pressure spray can cause paint chips or
other particles to become airborne.
• Always wear eye protection when using this equipment or in
vicinity of where equipment is in use.
• If you have questions about intended use, ask dealer or
contact Briggs & Stratton Power Products.
• NEVER operate units with broken or missing parts, or
without protective housing or covers.
• DO NOT by–pass any safety device on this machine.
• Before starting pressure washer in cold weather, check all
parts of the equipment to be sure ice has not formed there.
WARNING
• NEVER move machine by pulling on high pressure hose. Use
handle provided on unit.
Unintentional sparking can result in fire or
electric shock.
• Check fuel system for leaks or signs of deterioration, such as
chafed or spongy hose, loose or missing clamps, or damaged
tank or cap. Correct all defects before operating pressure
washer.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
• Disconnect spark plug wire from spark plug and place wire
where it cannot contact spark plug.
• This equipment is designed to be used with Briggs & Stratton
Power Products authorized parts ONLY. If equipment is used
with parts that DO NOT comply with minimum specifications,
user assumes all risks and liabilities.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
KNOW YOUR PRESSURE WASHER
Read this owner’s manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
Nozzle Extension with
Quick Connect
Fuel Tank
Recoil Starter
Air Filter
Spray Gun
Oil Fill Cap
Pressure
Control Knob
High Pressure Hose
Spray Tips
High Pressure Outlet
Pump equipped with
Automatic Cool Down System
Water Inlet
Chemical Injection Siphon/Filter
Air Filter — Protects engine by filtering dust and debris out
Nozzle Extension with Quick Connect — Allows you to
of intake air.
switch between five different spray tips.
Automatic Cool Down System — Cycles water through
pump when water reaches 125°-155°F. Warm water will
discharge from pump onto ground. This system prevents
internal pump damage.
Oil Fill Cap — Fill engine with oil here.
Pressure Control Knob — Varies the pressure of the high
pressure spray.
Pump — Develops high pressure.
Chemical Injection Siphon/Filter — Use to siphon
detergent or other pressure washer chemicals into the low
pressure stream.
Recoil Starter — Use for starting the engine manually.
Spray Gun — Controls the application of water onto
cleaning surface with trigger device. Includes safety latch.
Fuel Tank — Fill tank with regular unleaded gasoline. Always
Spray Tips — Chemical injection, 0°, 15°,and 40°: for
leave room for fuel expansion.
various cleaning applications.
High Pressure Hose — Connect one end to the water
Water Inlet — Connect garden hose here.
pump and the other end to the spray gun.
High Pressure Outlet — To connect high pressure hose.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
ASSEMBLY
PREPARING PRESSURE
WASHER FOR USE
IMPORTANT: Read entire owner’s manual before you
attempt to assemble or operate your new pressure washer.
If you have any problems with the assembly of your
pressure washer or if parts are missing or damaged, call the
pressure washer helpline at 1-800-270-1408.
Remove Pressure Washer From
Carton
• Remove the high pressure hose and parts box included
with pressure washer.
To prepare your pressure washer for operation, you
will need to perform these tasks:
1. Fill out and send in registration card.
2. Attach handle to main unit.
• Slice two corners at the end of carton from top to
bottom so the panel can be folded down flat, then
remove all packing material.
3. Install oil dipstick onto pump.
4. Add oil to engine.
• Roll pressure washer out of carton.
5. Add fuel to fuel tank.
Carton Contents
Items in the carton include:
6. Connect high pressure hose to spray gun and pump.
7. Connect water supply to pump.
8. Connect nozzle extension to spray gun.
9. Select and install desired nozzle.
•
•
•
•
•
Main Unit
High Pressure Hose
Handle
Pump Oil Dipstick (hanging on pump)
Accessory Box (includes the following):
Attach Handle to the Pressure
Washer
Use either a 13mm wrench or adjustable wrench to attach
the handle to the pressure washer.
•
•
•
•
(2) Bottles of engine oil
Owner’s registration card
Safety Goggles
To attach handle to the pressure washer:
Bag containing 5 multi–colored quick connect
spray tips
1. Slowly tip pressure washer forward and gently rest it
on front bumper.
•
•
•
•
•
•
•
•
•
Maintenance kit
2. Align holes on handle with holes on base.
Owner’s manual
3. Insert carriage bolts provided to hold handle in place
(Figure 1).
Figure 1 — Attach Handle to Pressure Washer
Engine manual
Engine warranty card
Emissions control warranty card
Spark arrester screen
Spray Gun with quick connect fitting
Nozzle extension with quick connect fitting
Handle hardware, including 4 carriage bolts and
4 flange nuts
If any of the above parts are missing or damaged, call the
pressure washer helpline at 1–800–270–1408.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
4. Secure handle to pressure washer using four provided
Add Engine Oil and Fuel
flange nuts.
• Place pressure washer on a level surface.
5. Slowly tip pressure washer back in place and insert
multi–colored spray tips in spaces provided in handle.
• Refer to engine owner’s manual and follow oil and fuel
recommendations and instructions.
Install Oil Dipstick on Pump
To install oil dipstick:
CAUTION
Any attempt to crank or start the engine before it has
been properly filled with the recommended oil will result
in equipment failure.
1. Make sure unit is on a level surface.
• Refer to engine manual for oil and fuel fill information.
CAUTION
You MUST remove the pump’s shipping cap and install
the oil dipstick.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTE: Check oil often during engine break–in. Refer to
engine owner’s manual for recommendations.
• Failure to do so will void the warranty and damage the
pump.
2. Remove and discard shipping cap located on pump
(Figure 2).
Connect Hose and Water Supply to
Pump
Figure 2 — Install Oil Dipstick onto the Pump
IMPORTANT: To avoid pump damage, you must
assemble the nozzle extension to the spray gun and attach
all hoses before you start the engine.
Remove shipping cap and
Shipping Cap
install oil dipstick here.
1. Uncoil high pressure hose and attach quick connect
end of hose to base of spray gun (Figure 3). Pull down
on collar of quick connect, slide onto spray gun and let
go of collar. Tug on hose to be sure of a tight
connection.
Figure 3 — Connect High Pressure Hose to Spray Gun
Connect high
pressure hose
here.
Pump Oil
Dipstick
NOTE: Remove and discard all pump shipping caps before
attaching hoses.
3. Install oil dipstick.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
2. Similarly, attach other end of high pressure hose to the
CAUTION
high pressure outlet on pump. Pull down on collar of
quick connect, slide onto pump and let go of collar.
Pull on hose to be sure of a tight connection.
There MUST be at least ten feet of unrestricted garden
hose between the pressure washer inlet and any flow
shut off device, such as a ‘Y’ shut-off connector or other
convenience-type water shut-off valve.
3. Before connecting garden hose to water inlet, inspect
inlet screen (Figure 4). Clean screen if it contains
debris or replace if damaged. Refer to the section
“O-Ring Maintenance” if inlet screen is damaged.
DO NOT run pressure washer if inlet screen is
damaged.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
6. Turn ON water and squeeze trigger on spray gun to
purge pump system of air and debris.
WARNING
Figure 4 — Connect Garden Hose to Water Inlet
High pressure spray can cause paint chips or
other particles to become airborne.
• Always wear eye protection when using this equipment or in
vicinity of where equipment is in use.
Inspect inlet
• Before starting the pressure washer, be sure you are wearing
adequate eye protection.
screen. DO NOT
use if damaged;
clean if dirty.
Checklist Before Starting Engine
Review the unit’s assembly to confirm you have performed
all of the following:
4. Run water through garden hose for 30 seconds to
clean out any debris. Turn off water.
1. Make sure handle is secure.
IMPORTANT: DO NOT siphon standing water for the
water supply. Use ONLY cold water (less than 100°F).
2. Make sure oil dipstick is installed onto pump.
3. Check for properly tightened hose connections.
5. Connect garden hose (not to exceed 50 feet in length)
to water inlet.Tighten by hand (Figure 4).
4. Check to make sure there are no kinks, cuts, or
damage to high pressure hose.
5. Check that oil has been added to proper level in
engine crankcase.
6. Add proper gasoline to fuel tank.
7. Provide a proper water supply (not to exceed 100°F).
8. Be sure to read “Safety Rules” and “How To Use Your
Pressure Washer” before using pressure washer.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
7. Select desired quick connect spray tip and insert it into
HOW TO USE YOUR
PRESSURE WASHER
end of nozzle extension (see “How To Use Spray
Tips”).
8. Engage safety latch to spray gun trigger (Figure 6).
Figure 6 — Spray Gun with Safety Latch Engaged
If you have any problems operating your pressure washer,
please call the pressure washer helpline at 1-800-270-1408.
How to Start Engine
The best way to start your pressure washer for the first
time is to follow these instructions step–by–step. This
starting information also applies if have let the pressure
washer sit idle for at least a day.
Safety Latch
9. Start engine according to instructions given in engine
owner’s manual.
1. Place pressure washer near an outside water source
capable of supplying water at a flow rate greater than
4.0 gallons per minute and no less than 20 PSI at
pressure washer end of garden hose.
CAUTION
Avoid injury from kickback.
2. Check that high pressure hose is tightly connected to
spray gun and pump. See “Preparing Pressure Washer
for Use” for illustrations.
• Squeeze trigger on spray gun each time recoil starter is
pulled and engine fails to start.
NOTE: Always keep the throttle lever in the “Fast”
position when operating the pressure washer.
3. Make sure unit is in level position.
4. Connect garden hose to water inlet on pressure
washer pump. Turn ON water.
How to Stop Pressure Washer
1. Let engine idle for two minutes.
CAUTION
DO NOT run the pump without the water supply
connected and turned on.
2. Turn engine off according to instructions given in
engine owner’s manual.
3. Squeeze trigger on spray gun to relieve
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
pressure in hose.
NOTE: A small amount of water will squirt out when
pressure is released.
5. Squeeze spray gun trigger until a steady stream of
water occurs.
6. Attach nozzle extension to spray gun (Figure 5).
Tighten by hand.
Figure 5 — Connect Nozzle Extension to Spray Gun
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
How to Use Spray Tips
The nozzle extension quick–connect allows the use of
several different spray tips. Each spray tip provides a
different spray pattern (Figure 7).
Cleaning and Applying Chemical
IMPORTANT: Use soaps designed specifically for
pressure washers. Household detergents could damage
the pump.
Follow these instructions to change spray tips:
1. Engage safety latch on spray gun.
CAUTION
You must attach all hoses before you start the engine.
CAUTION
A pressure washer produces a high pressure spray
which increases risk of injury and damage to unit.
• Starting the engine without all the hoses connected and
without the water turned ON will damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
• NEVER exchange spray tips without locking the safety latch
on the trigger.
To apply detergent follow these steps:
1. Review spray tip use.
2. Pull back collar on quick–connect and pull current
spray tip off.
2. Prepare detergent solution as required by
manufacturer.
3. Select desired spray tip:
3. Place chemical injection siphon/filter into detergent
container.
•
•
•
For gentle rinse, select white 40° or green 25°
spray tip.
To scour surface, select yellow 15° or red 0° spray
tip.
CAUTION
Keep the chemical injection tube from coming in contact
with the hot muffler.
To apply chemical, select black spray tip.
4. Pull back on collar, insert new spray tip and release collar.
Tug on spray tip to make sure it is securely in place.
• When inserting the filter into a detergent solution bottle,
route the tube so as to keep it from inadvertently contacting
the hot muffler.
5. For most effective cleaning, keep spray tip from 8 to
24 inches away from cleaning surface. DO NOT get
closer than 6 inches when cleaning automobile tires.
4. Make sure black spray tip is installed.
NOTE: Detergent cannot be applied with high pressure
spray tips (White, Green, Yellow, or Red).
Figure 12 — Spray Tips
Low Pressure
Use to apply
chemical
High Pressure
Black
White
40°
Green
25°
Yellow
15°
Red
0°
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
5. Make sure garden hose is connected to water inlet.
4. Increase or decrease spray pressure by turning
pressure control knob counterclockwise or clockwise
respectively (Figure 8). Use lower pressure to wash
items such as a car or boat. Use higher pressure to
strip paint and degrease driveways.
Check that high pressure hose is connected to spray
gun and pump; start engine.
6. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes. DO NOT allow
detergent to dry on (prevents streaking).
Figure 13 — Pressure Control Knob.
7. Allow detergent to soak in between 3–5 minutes
before washing and rinsing. Reapply as needed to
prevent surface from drying.
Pressure
Control
Knob
Pressure Washer Rinsing
After you have applied detergent, scour the surface
and rinse it clean as follows:
1. Apply safety latch to spray gun.
2. Remove black chemical spray tip from nozzle
extension.
5. Apply high pressure spray to small area and then check
surface for damage. If no damage is found, you can
assume it is okay to continue cleaning.
3. Select and install desired high pressure spray tip
following the instructions in “How to Use Spray Tips”.
6. Start at top of area to be rinsed, working down with
same overlapping strokes as used for cleaning.
WARNING
Automatic Cool Down System
(Thermal Relief)
High pressure spray could cause you to fall if
you are too close to the cleaning surface.
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures
above 125°F. The system engages to cool the pump by
discharging the warm water onto the ground.
• Keep spray nozzle between 8 to 24 inches away from cleaning
surface.
• Operate this unit on a stable surface.
• Be extremely careful if you must use the pressure washer from
a ladder, scaffolding or any other relatively unstable location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury if gun kicks back.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
SPECIFICATIONS
PRESSURE WASHER
MAINTENANCE
Rated Pressure . . . . . 3,000 PSI
Flow Rate . . . . . . . . . . 3.0 gallons per minute (gpm)
Check and Clean Inlet Screen
Examine the screen on the water inlet. Clean it if the
screen is clogged or replace it if screen is damaged.
Detergent . . . . . . . . . . Use detergent approved for
pressure washers
Water Supply
Temperature . . . . . . . Not to Exceed 100°F
Check High Pressure Hose
Automatic Cool . . . . Will cycle when water
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before using
it. Check for cuts, leaks, abrasions or bulging of cover,
damage or movement of couplings. If any of these
conditions exist, replace the hose immediately.
Down System
reaches 125°-155°F
Shipping Weight . . . . 145 lbs.
GENERAL MAINTENANCE
RECOMMENDATIONS
The pressure washer warranty does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain the high pressure washer as instructed in this
manual.
WARNING
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury and
possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST exceed maximum pressure
rating of unit.
• Some adjustments will need to be made periodically to
properly maintain your high pressure washer.
• All maintenance in this manual and the engine owner’s
manual should be made at least once each season.
Check Detergent Siphoning Tube
Examine the filter on the detergent tube and clean if
clogged. The tube should fit tightly on the barbed fitting.
Examine the tube for leaks or tears. Replace the filter or
tube if either is damaged.
• If equipped with inflatable tires, keep the air pressure at
the value marked on the tire or within 15 and 40 psi.
Before Each Use
1. Check engine oil level.
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must flush it
with clean water before stopping the engine.
2. Check water inlet screen for damage.
3. Check in-line filter for damage.
4. Check high pressure hose for leaks.
5. Check detergent siphoning tube and filter for damage.
1. Place chemical injection siphon/filter in a bucket full of
clean water.
2. Attach black low pressure spray tip.
3. Flush for 1-2 minutes.
4. Shut off engine.
6. Check spray gun, nozzle extension, and nozzles for
leaks.
7. Rinse out garden hose to flush out debris.
IMPORTANT: Simply shutting OFF engine will not
release pressure in the system. When the engine has
shut down, squeeze the trigger on the spray gun to
relieve the pressure in the hose.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
To remove contaminants from the pump, follow
these steps:
Check Gun and Nozzle Extension
Examine the hose connection to the gun and make sure it
is secure. Test the trigger by pressing it and making sure it
springs back into place when you release it. Put the safety
latch in the on position and test the trigger. You should not
be able to press the trigger.
1. Set up pressure washer as described in “Preparing
Pressure Washer For Use”. Connect water supply and
turn water on.
2. Start engine according to instructions in “To Start
Pressure Washer”.
Check In-Line Filter
Refer to Figure 14 and service the in-line filter if it
becomes clogged, as follows:
3. Remove nozzle extension from spray gun.
4. Squeeze trigger on spray gun and hold.
Figure 14 — Clean In-Line Filter
5. When water supply is steady and constant, engage
safety latch and reattach nozzle extension.
Filter Screen
Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure. The
principal cause of excessive pump pressure is a nozzle
clogged or restricted with foreign materials, such as dirt,
etc. To correct the problem, immediately clean the nozzle
using the tools included with your pressure washer and
follow these instructions:
Nozzle Extension
O-ring
1. Detach spray gun and nozzle extension from high
pressure hose. Detach nozzle extension from spray
gun and remove o-ring and screen from nozzle
extension. Flush the screen, spray gun, and adjustable
nozzle extension with clean water to clear debris.
1. Shut off engine and turn off water supply.
2. Remove spray tip from end of nozzle extension.
2. If screen is damaged, the o-ring kit contains a
replacement in-line filter screen and o-ring. If
undamaged, reuse screen.
3. Remove in-line filter from other end of nozzle
extension.
3. Place in-line filter screen into threaded end of nozzle
extension. Direction does not matter. Push screen in
with eraser end of pencil until it rests flat at bottom of
opening. Take care to not bend screen.
4. Use wire included in kit (or a small paper clip) to free
any foreign material clogging or restricting spray tip
(Figure 10).
Figure 10 — Nozzle Maintenance
4. Place o-ring into recess. Push o-ring snugly against
in-line filter screen.
5. Assemble nozzle extension to spray gun, as described
earlier in this manual.
Use wire here
to remove
debris
Purge Pump of Air and
Contaminants
5. Using a garden hose, remove additional debris by back
flushing water through nozzle extension (Figure 11).
Back flush between 30 to 60 seconds.
To remove air from the pump, follow these steps:
1. Set up pressure washer as described in “Preparing
Pressure Washer For Use”. Connect water supply and
turn water on.
Figure 16 — Backflushing the Nozzle Extension
2. Pull trigger on spray gun and hold.
3. When water supply is steady and constant, engage
safety latch.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
6. Reinstall spray tip and in-line filter into nozzle
Change pump oil as follows:
extension.
1. Clean area around brass oil drain plug at bottom of
pump.
7. Reconnect nozzle extension to spray gun.
8. Reconnect water supply, turn on water, and start
engine.
2. Remove oil drain plug. Drain oil completely into an
approved container.
9. Test pressure washer by operating with each Quick
Connect spray tip.
3. When oil has completely drained, install oil drain plug
and tighten firmly.
4. Clean area around pump oil dipstick. Remove dipstick
and fill pump with recommended oil to “Full” mark on
dipstick.
O–Ring Maintenance
Through the normal operation of your pressure washer,
o–rings, which keep the connections of the hoses and spray
gun tight and leak–free, may become worn or damaged.
5. Install pump oil dipstick.
6. Wipe up any spilled oil.
An O-Ring Maintenance Kit is provided with your pressure
washer which includes replacement o-rings, rubber washer
and water inlet filter. Refer to the instruction sheet
provided in the kit to service your unit’s o-rings. Note that
not all of the parts in the kit will be used on your unit.
ENGINE MAINTENANCE
See the engine owner’s manual for instructions on how to
properly maintain the engine.
To remove a worn or damaged o–ring; use a small flathead
screwdriver to get underneath the o-ring and pry it off.
CAUTION
Avoid prolonged or repeated skin contact with used
motor oil.
Pump Maintenance
Changing Pump Oil
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
Change oil after first 50 hours of operation and then every
200 hours or 3 months, whichever occurs first.
• Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
NOTE: When changing pump oil, use only high quality
nondetergent 30 weight oil. Use no special additives.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
NOTE: PumpSaver is available as an optional accessory. It is
not included with the pressure washer. Contact the nearest
authorized service center to purchase PumpSaver.
PREPARING THE UNIT
FOR STORAGE
Water should not remain in the unit for long periods of
time. Sediments or minerals can deposit on pump parts and
“freeze” pump action. If you do not plan to use the
pressure washer for more than 30 days, follow this
procedure:
CAUTION
You must protect your unit from freezing temperatures.
• Failure to do so will permanently damage your pump and
render your unit inoperable.
• Freeze damage is not covered under warranty.
1. Flush chemical injection hose by placing filter into a pail
of clean water while running pressure washer in low
pressure mode. Flush for one to two minutes.
CAUTION
Read and follow all cautions and warnings on the
2. Shut off engine and let it cool, then remove high
pressure and garden hoses. Disconnect spark plug wire
from spark plug.
PumpSaver can label.
• Always wear eye protection when using PumpSaver.
3. Empty pump of liquids by pulling engine recoil handle
about 6 times. This should remove most liquid from
pump.
To use PumpSaver, make sure the pressure washer is
turned off and disconnected from supply water. Read and
follow all instructions and warnings given on the PumpSaver
container.
4. Use pump saver to prevent corrosion build up and
freezing of pump.
NOTE: PumpSaver will drip from pump after treatment
and will stain wood and concrete.
5. Store unit in a clean, dry area.
NOTE: If PumpSaver is not available, draw RV antifreeze
(non-alcohol) into the pump by pouring the solution into a
3-foot section of garden hose connected to inlet adapter
and pulling recoil handle twice.
Protecting the Pump
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver to treat pump. This
prevents freeze damage and lubricates pistons and seals.
STORING THE ENGINE
See the engine owner’s manual for instructions on how to
properly prepare the engine for storage.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
NOTES
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
TROUBLESHOOTING
Problem
Cause
Correction
1. Low pressure spray tip installed.
1. Replace spray tip with high
pressure spray tip.
2. Water inlet is blocked.
2. Clear inlet.
3. Inadequate water supply.
4. Inlet hose is kinked or leaking.
5. Clogged inlet hose strainer.
3. Provide adequate water flow.
4. Straighten inlet hose, patch leak.
5. Check and clean inlet hose
strainer.
Pump has following problems:
failure to produce pressure,
erratic pressure, chattering, loss
of pressure, low water volume.
6. Water supply is over 100°F.
6. Provide cooler water supply.
7. Clear blocks in outlet hose.
7. High pressure hose is blocked or
leaks.
8. Gun leaks.
8. Replace gun.
9. Spray tip is obstructed.
10. Pump is faulty.
9. Clean spray tip.
10. Contact authorized service
facility.
1. Detergent siphoning tube is not
submerged.
1. Insert detergent siphoning tube
into detergent.
2. Chemical filter is clogged or
cracked.
2. Clean or replace filter/detergent
siphoning tube.
Detergent fails to mix with spray.
3. Dirty in-line filter.
3. See "Check In-Line Filter".
4. High pressure spray tip installed.
4. Replace spray tip with low
pressure spray tip.
Engine shuts down during
operation.
Out of gasoline.
Fill fuel tank.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
EXPLODED VIEW — UNIT
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
PARTS LIST — UNIT
Item Part #
Qty.Description
1
2
3
4
5
6
7
8
9
B190548GS
1 BASE
B2043GS
8 BOLT, Carriage
1 ASSY, Pump (see pages 20-23)
B2126AGS
CB3861CGS 1 HANDLE
B4160GS
99583GS
B2150GS
B2516GS
CB4105GS
1 DECAL, Instructions
9 NUT
1 HOOK, Square Neck
2 CAP, Vinyl
1 BUMPER
5 GROMMET
10 30809GS
11 187947AGS
12 191663GS
13 88521GS
14 190146GS
15 48031GGS
16 A1040DGS
17 A1041GS
18 B4805GS
19 87815GS
20 B1436BGS
21 23645GS
22 22237GS
23 191658GS
24 B3858GS
25 B1464GS
26 BB3061BGS
27 63281GS
28 191922GS
29 188194GS
1 DECAL, 5 QD Spray Tips
1 DECAL, Unit
2 ASSY, Wheel
2 NUT, Push
1 CLAMP, Hose
1 HOSE, Chemical Inject
1 FILTER, Chemical Hose
1 HOSE
1 GOGGLES, Safety
1 GUN
4 SCREW
4 WASHER, Lock
1 MANUAL, Owners
1 ASSY, Wand Ext. with QD
1 MANUAL, Honda
2 OIL BOTTLE
1 KEY
1 KIT, Maintenance
2 RIVET, Blind
30 11287628PGS 1 DIPSTICK, Pump
31 191413GS
32 186301GS
33 B1554GS
34 64416GS
35 52859GS
36 B4224GS
37 186839GS
38 97837GS
39 95458GP
40 B2384GS
900 NSP
2 VIB MOUNT, with Washer
1 KIT, Spray Tips, QD
1 VALVE, Thermal Relief
4 BOLT
4 NUT, Lock
1 SCREEN, Gun Inlet
1 GARDEN HOSE CONNECTOR
1 O-RING, High Pressure Hose
1 QUICK CONNECT
1 FILTER, Garden Hose Connector
1 ENGINE
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
EXPLODED VIEW — PUMP
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
PARTS LIST — PUMP
Item Part #
Qty Description
Item Part #
12187822PGS
Qty Description
1
2
110B2126GS
1
1
1
1
1
3
3
3
3
3
3
3
3
6
1
1
1
1
1
1
4
1
1
Cap
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
1
8
8
1
1
1
2
2
3
3
3
3
4
2
6
6
6
6
1
3
3
3
1
Seal
10887628PGS
112B2126GS
113B2126GS
11287628PGS
11187822PGS
11187822PGS
123B2126GS
11687628PGS
11587628PGS
115B2126GS
119B2126GS
120B2126GS
117B2126GS
118B2126GS
116B2126GS
12687628PGS
12587628PGS
149B2126GS
152B2126GS
155B2327GS
150B2126GS
151B2126GS
Circlip
10087822PGS
137B2126GS
136B2126GS
11787822PGS
10387628PGS
10487628PGS
10387628PGS
10587822PGS
10393360PGS
131B2126GS
16593360PGS
129B2126GS
126B2126GS
102B2126GS
10187822PGS
10287822PGS
10387822PGS
11193360PGS
106B2126GS
108B2126GS
10493360PGS
109B2126GS
Screw
Washer
Head
O-Ring
Plug
Plug
O-Ring
Gasket
Gasket
Rear Piston Guide
Seal
3
Snap Ring
Bearing
4
5
Oil Cap
6
Nut
7
Piston Washer
Piston
Spacer Disc
O-Ring
Piston Pin
Con Rod
Guiding Piston
Screw
Complete Rear Cover
O-Ring
Snap Ring
Bearing
Hollow Shaft
Grub Screw
Screw
Gas Engine Flange
Bushing
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Screw
Foot
Plug
O-Ring
Complete Valve
O-Ring
Plug
Support Ring
Piston Guide
O-Ring
Pump Body
Service Kits:
A
B
C
D
E
F
203-B2126GS 204-B2126GS 205-B2126GS
500-87628PGS 201-B2126GS 202-B2126GS
Valve Kit Piston Kit Oil Seal Kit
Water Seal
Kit
Support Ring
Kit
Pump Head
Kit
Item
Qty.
Item
Qty.
Item
Qty.
Item
Qty.
Item
Qty.
Item
Qty.
1
16
35
1
1
3
32
45
3
3
40
41
6
6
8
3
43
3
NA
NA
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
EXPLODED VIEW — UNLOADER
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Generac Portable Products 3000 PSI Pressure Washer
PARTS LIST — UNLOADER
Item Part #
Qty Description
Item Part #
Qty Description
1
2
210B2327GS
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Hose Tail
O-Ring
Stainless Ball
Spring
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
0
229B2327GS
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Ring
231B2327GS
211B2327GS
212B2327GS
213B2126GS
215B2327GS
137B2327GS
216B2327GS
217B2327GS
218B2327GS
220B2327GS
221B2327GS
222B2327GS
219B2327GS
223B2327GS
224B2327GS
225B2327GS
226B2327GS
227B2327GS
228B2327GS
230B2327GS
232B2327GS
234B2327GS
233B2327GS
235B2327GS
241B2327GS
240B2327GS
239B2327GS
238B2327GS
237B2327GS
236B2327GS
248B2327GS
155B2327GS
246B2327GS
245B2327GS
243B2327GS
244B2327GS
242B2327GS
153B2126GS
Washer
Lower Piston
O-Ring
Piston Guide
O-Ring
Suction Fitting
O-Ring
Washer
Bypass Fitting
Washer
Inlet Bolt
Plug
Screw
Nut
Knob
Housing
Pin
Spring Guide
Complete Unloader
3
4
5
Injector Body
Injector Nut
O-Ring
7
8
9
Spring
10
11
12
13
14
15
16
17
18
19
20
21
Plunger
O-Ring
Spacer Plate
Spring
Spring, Spacer Plate
Upper Piston
Pin
Ring
O-Ring
Inlet Bolt
Washer
Valve Housing
Service Kits:
250-B2327GS
Item
Qty.
Item
Qty.
Item
Qty.
11
17
18
20
22
1
1
1
1
2
23
2
25
27
32
1
3
1
1
1
30
29
8
1
1
1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAC PORTABLE PRODUCTS OWNER WARRANTY POLICY Effective January 1, 2003
LIMITED WARRANTY
"Generac Portable Products is a licensed trademark of Briggs & Stratton Power Products. Briggs & Stratton Power Products will
repair or replace, free of charge, any part, or parts of the equipment** that are defective in material or workmanship or both.
Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This
warranty is effective for the time periods and subject to the conditions provided for in this policy. For warranty service, find
your nearest Authorized service dealer by calling 1-800-270-1408. Warranty service may only be performed by a Briggs &
Stratton Power Products Authorized service dealer.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TIME PERIOD SPECIFIED, OR TO THE EXTENT PERMITTED
BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER
ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some countries or
states do not allow limitations on how long an implied warranty lasts, and some countries or states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives
you specific legal rights and you may also have other rights that vary from country to country or state to state.”
WARRANTY PERIOD*
Equipment **
Pressure Washer
Portable Generator
Consumer Use
1 Year
2 Years (2nd year parts only)
Commercial Use
90 Days
1 Year
* The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the
period of time stated in the table above. "Consumer use" means personal residential household use by a retail consumer.
"Commercial use" means all other uses, including use for commercial, income producing or rental purposes. Once equipment has
been used commercially, it shall thereafter be considered to be in commercial use for purposes of this warranty.
** The engine and starting batteries are warranted solely by the manufacturers of those products.
WARRANTY REGISTRATION IS NOT NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON
POWER PRODUCTS EQUIPMENT. SAVE YOUR PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE
PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE
MANUFACTURING DATE OF THE EQUIPMENT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
About your equipment warranty:
We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized service dealer may perform warranty
repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For
example, warranty service would not apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping,
handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the
equipment has been removed or the equipment has been altered or modified. During the warranty period, the Authorized service
dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal use and service.
This warranty will not cover following repairs and equipment:
• Normal Wear: Outdoor power equipment, like all mechanical devices, needs periodic parts, service and replacement to
perform well. This warranty does not cover repair when normal use has exhausted the life of a part or the equipment.
• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or
unauthorized installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper
maintenance, repair or storage so as, in our judgment, to adversely affect its performance and reliability. This warranty also
does not cover normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon or
lime, etc.).
• Other Exclusions: Also excluded from this warranty are wear items such as quick couplers, oil gauges, belts, o-rings, filters,
pump packing, etc., pumps which have been run without water supplied or damage or malfunctions resulting from accidents,
abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration. Accessory parts such as guns,
hoses, wands and nozzles are excluded from the product warranty. Also excluded is used, reconditioned, and demonstration
equipment; equipment used for prime power in place of utility power and equipment used in life support applications.
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
JEFFERSON, WISCONSIN, U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|