Earn BISSELL Rewards!
Register your
product today!
See details on
back page
USER'S GUIDE
44M3, 67F8 SERIES
2
3
Thank You
Safety instructions
Product view
4
5
Assembly
6-9
Operations
10-15
16-17
17
Maintenance and care
Troubleshooting
Replacement parts
18
19
20
20
Accessories
Warranty
Product registration
Consumer services
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
■ Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
■ Turn off all controls before plugging or
Read all
unplugging vacuum cleaner.
instRuctions
befoRe using youR
upRight VacuuM.
■ Use extra care when cleaning stairs.
■ Do not pick up flammable materials
(lighter fluid, gasoline, kerosene, etc.) or
use in the presence of explosive liquids
or vapors.
Always connect to a polarized outlet
(left slot is wider than right). Unplug from
outlet when not in use and before conducting
■ Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
mainteWnancea. Rning: to
■ Do not use vacuum cleaner in an
enclosed space filled with vapors given
off by oil base paint, paint thinner, some
moth proofing substances, flammable
dust, or other explosive or toxic vapors.
reduce the risk of fire,
electric shock, or injury:
■ Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■ Do not pick up hard or sharp objects
such as glass, nails, screws, coins, etc.
■ Do not leave vacuum cleaner unattended
■ Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
■ Do not use without filters in place.
■ Use only on dry, indoor surfaces.
■ Keep appliance on a level surface.
when it is plugged in.
■ Unplug from outlet when not in use and
before servicing.
■ Unplug before attaching the TurboBrush.
■ Do not use outdoors or on wet surfaces.
■ Do not allow children to operate vacuum
■ Do not carry the vacuum cleaner while it
cleaner or use as a toy.
is running.
■ Close attention is necessary when used
■ Hold plug when rewinding onto cord
reel. Do not allow plug to whip when
rewinding.
by or near children.
■ Do not use for any purpose other than
described in this user’s guide.
saVe these
■ Use only manufacturer’s recommended
attachments.
instRuctions
foR futuRe use
■ Do not use with damaged cord or plug.
■ If appliance is not working as it should,
has been dropped, damaged, left out-
doors, or dropped into water, have it
repaired at an authorized service center.
■ Do not pull or carry by cord, use cord as
a handle, close a door on cord, or pull
cord around sharp edges or corners. Do
not run appliance over cord. Keep cord
away from heated surfaces.
this appliance
has a polaRiZed
plug.
To reduce the risk of electric shock, this
appliance has a polarized plug (one blade
is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not
change the plug in any way.
■ Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
■ Do not handle vacuum cleaner or plug
with wet hands.
■ Do not put any object into openings. Do
not use with any opening blocked; keep
openings free of dust, lint, hair, and any-
thing that may reduce air flow.
This model is for household use only.
3
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product view
Stretch Hose
Hose Clip
Pet TurboBrush® Tool
Pet TurboEraser™ Tool
(67F8 series)
®
Quick Reach
Handle
Clean Filter
Indicator
Carrying
Handle
Crevice Tool
Combination
Dusting Brush/
Upholstery Tool
Extension
Wand
Dirt
Container
HEPA Media
Filter
Cord Rewind
Filter Cup
Hose
Lock'n
Seal™ Lever
Headlight
Wand
Automatic
Cord Rewind
Handle
Release Pedal
Hose
Wand
Base
Pet Hair
Lifter
Foot
Hose
Powerfoot
Furniture
Protection Guard
WaRning:
Plastic film can be
caution:
Do not plug in your vacuum
cleaner until you are famil-
iar with all instructions and
operating procedures.
dangerous. To avoid
danger of suffocation,
keep away from babies
and children.
4
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
you need: phillips head screwdriver.
attach handle to vacuum
1. Locate the vacuum handle and remove
the screw packet (1 screw) taped to the
base of the handle.
2.
2. Stand the vacuum upright and slide
the base of the handle firmly into the
grooves at the top of the vacuum body.
3. IMPORTANT – Continue to push firmly
until the handle is flush with the front of
the vacuum body.
4.
4. Insert the screw provided and tighten
securely.
attach vacuum hose and tools
1. Attach the Twist ‘n Snap™ hose by lining
up the tabs on the base with the cor-
responding notches on the back of the
vacuum. Turn the Twist ‘n Snap hose to
the right to lock the hose into place.
1.
2. Grasping the Quick Reach® handle,
slide the end of the hose wand onto the
hose wand base. Snap the hose into the
hose clip.
note: the powerfoot will not
suction properly unless the hose
wand is firmly attached.
4.
3. Slide the extension wand and the crevice
3.
2.
tool together into the storage holder.
4. Snap the combination tool into the stor-
age clip.
5. Attach the Pet TurboBrush by aligning the
small holes near the brush roll with the
tabs at the bottom of TurboBrush hous-
ing. Snap TurboBrush into place.
5.
note: 67f8 series includes pet
turboeraser™ tool.
6. Flip the Pet Hair Lifter down until it clicks
6.
into place on the front of the foot.
note: flip the pet hair lifter down
for carpeted surfaces and up for
non-carpeted surfaces.
5
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
automatic power cord rewind
1. Gently pull out power cord and stop when
yellow line is visible. Do not pull power cord
beyond the red line. Plug cord into electrical
outlet.
2. To return cord, with vacuum power button
OFF, remove plug from outlet. Hold plug and
press automatic cord button to wind cord
into reel. Do not allow plug to whip when
rewinding.
power switch
the power switch is located just below the
hand on the side of the vacuum.
i - on o - off
CAUTION:
Be careful to avoid injury
as cord retracts very
quickly.
handle position
press the handle release pedal with your
foot to place vacuum into one of three
cleaning positions.
1. upright: For storage, transporting, and above
floor cleaning with tools.
•Transporting in upright position by tilting
vacuum on rear wheels and push forward or
use carrying handle on back of handle base.
2. normal cleaning: Press handle release
pedal once for most household floor cleaning.
3. low cleaning: From normal cleaning posi-
tion, press handle release pedal once for
cleaning under low furniture.
caution:
Before using your vacuum, make
sure that the dirt container is in
locked position and that all
filters (inner circular, outer
circular, pre-motor and post-
motor) are in place. Do not
operate your vacuum without
these filters.
6
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
height adjustment
turn dial on powerfoot to adjust to one
of five height adjustments. if dial is dif-
ficult to turn, tilt the cleaner back slightly
to take the weight off the foot while
turning.
lowest setting – For low pile carpet or
bare floors.
Medium setting – For medium pile carpet.
highest setting – For high pile and most
shag carpet. Adjust to high setting if difficult
to push.
Tip:
Before cleaning under low furniture,
check area first for objects that might
harm the unit or block the vacuum hose.
7
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
clean filter indicator
the indicator tells you when air flow in
the vacuum is reduced due to dirty filters
or a clog in the hose. the indicator will
remain green until the air flow is reduced
– and then will change to red. When fully
red, the air flow is greatly reduced or
clogged by a dirty filter; follow instruc-
tions on page 11 to clean/replace your
filters.
pet hair lifter
use to pick up pet hair from carpeted
surfaces. Vacuum like you normally
would, as you pull the vacuum back pet
hair collects on the lifter and releases it
into the vacuum path as you push for-
ward.
Clean Filter Indicator
1.
note: turn vacuum off before you flip
pet hair lifter up or down.
1. To vacuum carpeting, flip down until it clicks
into place.
2. To vacuum non-carpet surfaces, push the yellow
release button located in the center just above
the feature.
2.
8
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
tools
attach desired tool to hose for above
floor cleaning or hard to reach areas.
1. Raise handle to upright position.
2. Grasp the Quick Reach handle and lift hose
wand to separate from suction intake
opening.
Tip:
3. Attach tools by firmly pushing onto
vacuum hose or extension wand.
Hair, string and small
objects can block the
vacuum hose or
tools. Check them
regularly for
Crevice tool
Use in tight narrow spaces.
Combination dusting
brush/upholstery tool
Two types of cleaning tools are included
in one attachment. Rotate for desired tool.
Use brush side to dust furniture, blinds,
books, lamps, shelves and baseboards.
Use the upholstery tool on cushions, drap-
eries and fabrics.
obstructions.
Extension wand
Use with desired attachment for a longer reach.
pet contour tool®
(select models only)
Use to reach into corners and edges on stairs
as well as armrests and other curved surfaces.
The tool can be flipped to use in any direction.
pet turbobrush® tool
67F8 series includes Pet TurboEraser™
Tool. Use rotating brush action for small
flat areas such as cushions and beds.
note: press gently down and pull
towards you in a raking motion. too
much pressure will cause the brush
to stop rotating.
notice:
These tools are designed to
remove pet hair from upholstered
or carpeted surfaces. They should
not be used on pets.
CAUTION:
The rotating floor brush continues to rotate while tools are
in use. To reduce the risk of injury from moving parts, always
move the cleaner with the carrying handle at the back of the
cleaner. Always place vacuum cleaner on floor with handle in
upright position when using tools. Never place your fingers
under the cleaner when it is running. Never place powerfoot
on furniture or uneven surfaces. Do not place vacuum cleaner
close enough to objects to pull them into rotating brush.
9
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
to maximize performance and extend
life of your vacuum it is very important
to perform the following maintenance
steps:
2.
Full Line
empty dirt container
empty when dirt reaches the "full" line
on the container.
Unlock
Lock
Position
Position
1. Turn power OFF. Unplug vacuum cord
3.
from electrical outlet.
2. Slide the Lock ‘n Seal lever to the
"Unlock" position.
3. Grasp dirt cup handle and pull straight
out to remove from vacuum and empty.
4. Place dirt container back in the vacuum
and slide the lever to the "Lock" position.
note: the dirt container may be
washed in warm water with a
mild detergent. Make sure it is
completely dry before replacing.
Tip:
For maximum cleaning performance,
check and clean or replace all filters
as suggested.
WaRning:
To reduce the risk of
electric shock, turn power
switch OFF and disconnect
polarized plug from electri-
cal outlet before performing
maintenance or
troubleshooting checks.
10
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
cleaning the inner & outer circular filters
1. Turn power off. Unplug the cleaner from
electrical outlet.
2.
2. Remove the dirt container as described in
the previous section. Grasp the filter cup
located at the bottom of the dirt container,
lift up and out. do not tRy to pull
ciRculaR foaM filteR out of
the filteR cup While it is still in
the VacuuM.
3. Grasp the plastic tab on the top of the circu-
lar foam filters. Twist to unlock and pull out.
3.
4. Separate the outer foam and inner pleated
circular filters. Wash each individually by
hand in warm water. Mild detergent may
be used if desired. Rinse well, then air dry
thoroughly before putting them back together
and replacing in filter cup.
6.
5. The filter cup may be washed in warm water
with a mild detergent. Make sure it is com-
pletely dry before reassembling with filters.
do not put in dishWasheR.
6. The upper tank and louvers may also be
wiped clean with a damp cloth. Reach
underneath the upper tank and turn the
rim of the louvers to left to unlock. Pull
straight down to remove. Make sure all
parts are completely dry before replacing.
7. To replace louvers lift back into upper
tank. Place top of louvers inside clear
center cavity and turn toward the right to
unlock until tabs fit into notch. Continue to
turn to right until tight.
cleaning the pre-motor filter
the pre-motor protects the motor from
WARNING:
Do not operate cleaner with
damp or wet filters or without
all filters in place.
debris.
1. Turn power OFF. Unplug vacuum cord
from electrical outlet.
2. The pre-motor filter is located underneath
the filter cup in the center of the round
part of the Lock ‘n Seal lever.
3. Remove the small round filter and any
Pre-Motor
Filter
debris on top of it. Rinse well under
warm water, air dry completely before
replacing.
11
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Replacing the post-motor filter
the post-motor assists in the filtration
Remove
Filter
process to return clean air to the room.
Open
Door
1. Turn power OFF. Unplug vacuum cord
from electrical outlet.
2. Locate filter behind the door on the side of
the vacuum. Remove and replace when fil-
ter becomes dirty. The white, pleated HEPA
media filter is not washable.
checking rotating floor brush and drive belt
check your vacuum's rotating floor
brush and drive belt regularly for
wear or damage.
3.
1. Turn power OFF. Unplug vacuum cord
from electrical outlet.
2. Place handle in low position and turn
vacuum cleaner over so bottom side is up.
3. Remove the seven screws with a Phillips
head screwdriver. Lift the brush cover off.
4. Grasp rotating floor brush at both ends and
lift.
Brush Cover
5. Clean strings, hair and other debris from
rotating floor brush, paying particular
attention to brush ends.
8.
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts or
stressed areas.
8. Check air passageway for obstructions.
Remove debris from this area.
Air Passageway
12
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Replace drive belt
1. Turn power OFF. Unplug vacuum cord
from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (steps 1-4 of Check rotat-
ing floor brush and drive belt), grasp old
drive belt and remove from motor pulley.
Discard old drive belt.
3.
Motor
Pulley
3. Place new drive belt over motor pulley
and stretch other end over rotating floor
brush in the space between the bristles.
4. Place ends of rotating floor brush down
into slots on sides as shown.
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center
itself on rotating brush.
4.
6. Reposition brush cover and screw back
Motor
Pulley
into place.
13
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
pet turbobrush® tool Maintenance
note: 67f8 models include the pet
turboeraser™ tool that follows the
same maintenance steps as the pet
2.
turbobrush® tool.
1. Turn power OFF. Unplug vacuum cord
from electrical outlet.
2. Turn tool so bottom side faces up and remove
the two screws.
3. Remove the faceplate and clear any
obstructions.
4. Remove the brush from the drive belt to
clean debris.
5. Reposition the drive belt on the brush, and
place ends of brush in slots on the side.
Reposition faceplate and secure with
two screws.
note: this tool is designed to
remove pet hair from upholstered or
carpeted surfaces. it should not be
used on pets.
14
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
clearing clogs
3.
low suction or poor pickup may be
due to a clog in the vacuum cleaner. if
you notice a change in the sound of the
motor, check for clogs.
1. Turn power OFF. Unplug vacuum cord
from electrical outlet.
2. Empty dirt container.
3. Check upper tank for build up or clogs.
4. Check the suction inlet for a clog.
4.
Suction
inlet
5. Grasp the Quick Reach handle and lift
hose wand to separate from the suction
opening. Check for a clog in the base, the
wand or the hose.
6. Remove the screw attaching the hose
wand base to the vacuum. Straighten the
hose wand base and unclog with long,
narrow object such as a broom stick.
5.
7. If the clog persists, follow the instructions
for checking the rotating floor brush on
page 12 and inspect the air passageway
for obstructions
Replace headlight
1. Turn power OFF. Unplug vacuum cord
from electrical outlet.
2.
2. Using a flat screwdriver, table knife or
coin, insert into the slot on the right of the
lens and gently push inner latch to the left
as shown to remove the lens.
3. Reposition lens by inserting the tab on left
side and then pushing the right side back
into place.
3.
15
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Vacuum cleaner won’t turn on
possible causes
Remedies
1. Power cord not plugged in
2. Blown fuse/tripped breaker
3. Damaged cord
1. Check electrical plug
2. Check/replace fuse or reset breaker
3. Refer to a BISSELL authorize service center
for repair or replacement
Vacuum cleaner won't pick up dirt
possible causes
Remedies
1. Incorrect height adjustment
1. Adjust powerfoot to correct height setting
2. Hose not attached to suction opening
2. Grasp quick reach handle and firmly push hose wand onto
the suction opening
3. Crack or hole in hose
3. Check hose and replace if needed
4. Replace drive belt, see page 13
5. Replace brush
4. Broken or worn drive belt
5. Rotating floor brush bristles worn
6. Rotating floor brush jammed
7. Clog in vacuum
6. Remove brush and clean debris from brush ends
7. Follow instructions on page 15 for clearing clogs
8. Empty dirt container
8. Dirt container full
9. Dirt container or upper tank not installed properly
9. Position correctly and lock in place
10. Maintaining Pet TurboBrush see pg 14
®
10. Pet TurboBrush is clogged or debris is wrapped
10. Filters are dirty
10. Check and clean pre-motor and HEPA media
post-motor filters, see pages 11 & 12
tool won't pick up dirt
possible causes
Remedies
1. Crack or hole in hose
1. Check hose and replace if needed
2. Follow instructions on page 15 for clearing clogs
3. Empty dirt container
2. Clog in vacuum
3. Dirt container full
4. Dirt container or upper tank not installed properly
5. Filters are dirty
4. Position correctly and lock in place
5. Check and clean pre-motor and post-motor filters
see pages 11 & 12
Visible dirt escaping from cleaner
possible causes
Remedies
1. Dirt container full
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check pre-motor and post-motor
filters for correct installation see pages 11 & 12
cord will not retract
possible causes
Remedies
1. Knotted or twisted
1. Follow instructions on page 6
16
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
other maintenance or service not included in the manual should be
performed by an authorized service representative.
thank you for selecting a bissell product.
please do not return this product to the store.
for any questions or concerns, bissell is happy to be of
service. contact us directly at 1-800-237-7691.
Replacement parts - BISSELL vacuum
Item
Part No.
Part Name
1
32074
Style 9 Drive Belt (2-Pack)
2
3
203-1297
203-2468
203-2449
32R9
73K1
69B1
32076
203-1215
203-7130
Standard Headlight Bulb
Hose Assembly
Brush Dowel (15")
Style 16 Inner and Outer Circular Pre-Motor Filter Set
Style 16 Inner Circular Pre-Motor Filter
Style 16 Outer Circular Pre-Motor Filter
Style 7/9/16 Post-Motor HEPA Media Filter
Style 7/9/16 Pre-Motor Filter
Pet Hair Lifter
4
5
6
7
8
9
10
1
7
2
8
3
4
5
6
9
10
17
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories - BISSELL vacuum
these items are available for purchase as accessories for your
bissell vacuum: to purchase call
1-800-237-7691 or visit www.bissell.com.
Item
Part No.
Part Name
1
203-2447
Pet TurboBrush® Tool (44M3 series only)
2
3
4
5
6
203-1063
203-1099
203-1084
203-1368
203-7529
Crevice Tool
Combination Dusting/Upholstery Brush
Extension Wand
Pet Contour Tool® (44M3 series only)
Pet TurboEraser™ Tool (67F8 series only)
1
2
3
4
5
6.
18
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty - BISSELL Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may
vary from state to state. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,
telephone, or regular mail as described below.
limited three year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or
products), at BISSELL’s option, free of charge from the date of purchase by the original
purchaser, for three years any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any
other use not in accordance with the User's Guide is not covered.
if your bissell product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your
area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Services.
Website or e-mail:
Use the “Customer Support” tab.
or call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
*eXceptions and eXclusions fRoM the teRMs of the liMited WaRRanty
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE THREE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED
ABOVE.
Some states do not allow limitations on how long an implied warranty last so the above limitation
may not apply to you.
19
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Don't forget to register your product!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
bissell Rewards points
Automatically earn points for discounts and free shipping on future purchases.
faster service
Supplying your information now saves you time should you need to contact us with
questions regarding your product.
product support Reminders and alerts
We’ll contact you with any important product maintenance reminders and alerts.
special promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit www.bissell.com/registration now!
BISSELL consumer services
For information about repairs or replacement parts, or questions about your warranty, call:
bissell consumer services
1-800-237-7691
Monday - Friday 8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
note: please keep your original sales receipt. it
provides proof of purchase date in the event of a
warranty claim. see Warranty on page 19 for details.
©2011 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 110-4312
Rev 1/11
Visit our website at:
20
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Download from Www.Somanuals.com. All Manuals Search And Download.
|