KD Owner’s Manual
BILLY GOAT KD VACUUM
Owner's Manual
KD612, KD512HC, KD512HCS
Accessories
Optional Debris bags
ZIPPERLESS
QUICK BAG
SHREDDER
KIT
ON BOARD
VACUUM
NOZZLE WEAR
PLATES
CASTER KIT
STANDARD
TURF PRO
DEBRIS BAG
COVER
For non-dusty
conditions that
are damaging
to zippers.
(STD. ON
Shreds
4"(102mm) x
7' (2.13m)
For
vacuuming in
hard to reach
areas.
For use on
hard surface.
For use in
leaves and
grass in non-
dusty
Directs dust
downward
away from
operator.
KD512HCS)
Extends nozzle
life when used
along curbs and
hard surfaces.
leaves,
reducing total
volume.
conditions.
P/N 890309
P/N 890209
P/N 890041
P/N 890413
P/N 890412
P/N 890028
P/N 900801
Part No 890033
Form No F062306A
1
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
SERIAL PLATE DATA
Record the model number, serial number, date of
purchase, and where purchased.
Purchase Date:
Purchased From:
Specifications
KD612
KD512HC
KD512HCS
Engine: HP
6.0 (4.47 kW)
5.5 (4.11 kW)
5.5 (4.11 kW)
Engine: Type
B & S QUANTUM
112K020124E1
1.5 qt. (1.4 L)
0.63 qt. (0.6 L)
98# (44.5 kg)
62” (1.57m)
26.75” (0.68 m)
42” (1.07m)
200
HONDA OHC
GCV160AN1A
1.16 qt. (1.1 L)
0.58 qt. (0.6 L)
99# (45.0 kg)
62” (1.57m)
26.75” (0.68 m)
42” (1.07m)
200
HONDA OHC
GCV160AN1A
1.16 qt. (1.1 L)
0.58 qt. (0.6 L)
99# (45.0 kg)
62” (1.57m)
26.75” (0.68 m)
42” (1.07m)
200
Engine: Model
Engine: Fuel Capacity
Engine: Oil Capacity
Total Unit Weight:
Overall Length
Overall Width
Overall Height
Max. operating slope
Lwa at operator position
Lpa at operator position
Vibration at operator position
111 dBa
111 dBa
111 dBa
97 dBa
0.34 g (3.29m/s2)
97dBa
0.27 g (2.86m/s2)
97dBa
0.27 g (2.86m/s2)
Part No 890033
Form No F062306A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
GENERAL SAFETY INSTRUCTIONS and SYMBOLS
The safety symbols shown below are used throughout this manual. You should become familiar with them before
assembling, operating, or servicing this equipment.
This symbol indicates important information that will prevent injury to yourself or others.
This symbol indicates ear protection is recommended when operating this equipment.
This symbol indicates eye protection is recommended when operating this equipment.
This symbol indicates gloves should be worn when servicing this equipment.
This symbol indicates that this manual and the engine manufacturer’s manual should be read
carefully before assembling, operation, or servicing this equipment.
®
This symbol indicates important information that will prevent damage to your BILLY GOAT
KD Vacuum.
This symbol indicates the engine oil level should be checked before operating this
equipment.
Read and make sure you thoroughly understand the following safety precautions before assembling, operating or
servicing this equipment:
READ this manual and the engine manufacturer’s manual carefully before assembling,
operating, or servicing this equipment.
EAR PROTECTION is recommended when operating this equipment.
EYE PROTECTION is recommended when operating this equipment.
BREATHING PROTECTION is recommended when operating this equipment.
EXHAUST from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land
unless a spark arrester is installed on the muffler as required by Section 4442 of the
California Public Resources Code. The arrester must be maintained in good working order.
Other states may have similar laws. Federal laws apply on federal lands.
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an
odorless and possibly fatal poison.
Part No 890033
Form No F062306A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is
recommended.
DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least
two minutes before refueling.
DO NOT store gasoline near an open flame.
DO NOT remove gas cap while engine is running.
DO NOT start or operate engine if strong odor of gasoline is present.
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until
gasoline has completely evaporated.
DO NOT smoke while filling the fuel tank.
DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark
tester.
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if
necessary. If equipped with muffler deflector, inspect deflector periodically and replace if
necessary.
DO NOT operate engine with grass, leaves or other combustible material near the muffler.
DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may
cause severe burns.
DO NOT leave equipment unattended while in operation.
DO NOT park equipment on a steep grade or slope.
DO NOT operate equipment with bystanders in or near the work area.
DO NOT allow children to operate this equipment.
DO NOT operate equipment with guards removed.
DO NOT operate equipment near hot or burning debris or any toxic or explosive materials.
DO NOT operate equipment on slopes greater than specified in Specifications section of this
manual.
DO NOT place hands or feet underneath unit, or near any moving parts.
ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting.
ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary.
ALWAYS keep hands and feet away from moving or rotating parts.
ALWAYS store fuel in approved safety containers.
WARNING: Important
Remove all rocks, wire, string, plastic, etc. that can present a hazard during work prior to
starting.
DO identify and mark all fixed objects to be avoided during work such as sprinkler heads,
water valves, buried cables, or clothes line anchors, etc.
Part No 890033
Form No F062306A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
SOUND
SOUND LEVEL 97 dB(a) at Operator Position
Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 2-21-2002 under the
conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on
the unit for the sound power level for your model.
General Conditions:
Temperature:
Sunny
45oF (7.2oC)
5 mph (8.1 kmh)
South West
60%
Wind Speed:
Wind Direction:
Humidity:
Barometric Pressure:
30.18”Hg (767 mm Hg)
VIBRATION DATA
VIBRATION LEVEL 0.34g (3.29m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using
calibrated vibration test equipment. Tests were performed on 5-25-2006 under the conditions listed below.
General Conditions:
Temperature:
Sunny
89oF (31.7oC)
13.6 mph (21.9kph)
East
Wind Speed:
Wind Direction:
Humidity:
Barometric Pressure:
22.8%
29.9Hg (101.3kpa)
INTENDED USE
INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter
and for chipping brush, limbs, corn and sunflower stalks and palm fronds.
Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's
primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine.
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check
for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects.
Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 12).
Part No 890033
Form No F062306A
6
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT ® KD Vacuum. If any labels are damaged or missing, replace them before operating
this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The
correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS
AND FEET AWAY
LABEL EAR EYE BREATHING ITEM #49
P/N 890254
DANGER FLYING DEBRIS
ITEM # 62 P/N 810736
ITEM #29 P/N 400424
LABEL READ MANUAL
ITEM #84 P/N 430363
LABEL EXPLOSIVE FUEL
ITEM # 63 P/N 400268
DEBRIS BAG LABEL
ITEM #1
ENGINE LABELS
HONDA
BRIGGS & STRATTON
Read Owner’s Manual Before Operating.
Lire le manuel d’utilisation avant la mise en route.
Vor Inbetriebnahme Bedienungs - und Wartungsanleitung lesen.
Favor leer las instrucciones de operacion antes de operar el motor.
Consultare il Manuale Uso e Manutenzione prima dell utilizzo.
Las Skotselinstruktionen Innan Start.
ENGINE CONTROLS
Honda
Choke
Control
Throttle Control
Choke Control
Throttle
Control
Fuel Shut Off
Briggs engines have a primer
button carburetor rather than
choke type carburetor.
Part No 890033
Form No F062306A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
PACKING CHECKLIST
Your Billy Goat KD Vacuum is shipped from the factory in one carton, completely assembled except for the
upper handle, debris bag, and bag quick disconnect.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached by
cables and folded over
PUT OIL IN ENGINE BEFORE STARTING
PARTS BAG &
Warranty card P/N- 400972, Owner’s Manual P/N-890033, Declaration of Conformity P/N-890393.
Boxing Parts
Checklist
Debris Bag
P/N-890022
Literature Assy
P/N-890392
Connector Quick
Disconnect
P/N-890176
Quick disconnect
Honda 5.5GVC
160
Briggs & Stratton
6.0 HP Intek
Fig. 2
ASSEMBLY
1. ASSEMBLE Lift upper handle (item 6), remove items 8, 30, & 32 from lower handle (item 27). Attach and secure
upper handle as shown using same hardware.
2. UNFOLD the debris bag (item 1) and fasten bag neck to bag quick disconnect (item 64). Attach firmly to housing
exhaust (item 52) see fig. 2.
3. ATTACH bag hanger strap to bag supports (item 11), preassembled to upper handle.
4. CONNECT spark plug wire.
Part No 890033
Form No F062306A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
OPERATION
Like all mechanical tools, reasonable care must be used when operating machine.
Inspect machine work area and machine before operating. Make sure that all operators of this
equipment are trained in general machine use and safety.
PUT OIL IN ENGINE BEFORE STARTING
STARTING
ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine
must be level when checking and filling oil and gasoline.
ENGINE SPEED: Controlled by throttle lever on the engine. Under normal conditions, operate at minimum
throttle to accomplish your current cleaning task.
FUEL VALVE: Move fuel valve to "ON" position (when provided on engine).
CHOKE: Located on engine and must be controlled manually.
PRIMER: Push primer per engine instructions (B&S only).
THROTTLE: Located on engine and must be controlled manually.
IF YOUR UNIT FAILS TO START
:
See Troubleshooting on page 12.
HANDLING & TRANSPORTING
:
This unit requires two people to lift it. With the handle in the folded position, lift holding the
lower handle and belt/shaft guard one on each side of the machine. Secure the machine in place
during transport. See page 3 for weight specifications
Never lift the machine while the engine is running.
STORAGE
Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach
an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as follows:
Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and
causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Be
sure engine is cool. Do not smoke. Run engine until fuel tank is empty and engine runs out of gasoline.
Part No 890033
Form No F062306A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
OPERATION
VACUUMING OPERATION
VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle and
pulling height adjust knob on the handle (item 23) up at left rear of machine.
FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle. NOTE:
Never bury nozzle into debris.
CLEARING A CLOGGED NOZZLE & EXHAUST: Turn engine off and wait for impeller to stop completely
and disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp
materials. Reconnect spark plug wire.
DEBRIS BAG
Debris bags are normal replaceable wear items.
Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.
An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional
Accessories shown on page 1).
DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag. Your
new bag requires a break-in period to condition the pores of the material against premature blockage. The entire bag surface
serves as a filter, and must be able to breath to have good vacuum performance. Be sure engine has come to a complete stop
before removing or emptying bag.
This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings
page 4-5).
However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas.
Dust is the greatest cause of lost vacuum performance. However, following these rules will help maintain your
machine's ability to vacuum in dusty conditions:
• Run machine at idle to quarter throttle.
• The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup
performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake
bag free of dust.
• Pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use.
NOTE: Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned.
DO NOT leave debris in bag while in storage.
COMPOST
Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to
provide enriched soil for later use as fertilizer in gardens and flower beds
NOTE: Allow green chips to dry before spreading around living plants.
Part No 890033
Form No F062306A
10
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use (daily)
Every 5 hrs (daily)
Every 25 Hours
ò
Inspect for loose, worn or damaged parts.
Clean Debris bag
ò
ò
Check bag strap tightness
Engine (See Engine Manual)
Check for excessive vibration
Lubricate wheels
ò
ò
IMPELLER REMOVAL
1.Wait for engine to cool and disconnect spark plug.
2.Drain fuel and oil from the engine.
3. Remove bag, quick release, and upper handle. Do not kink, stretch, or break control cables, control
housings, or end fittings while removing handles.
4. Remove housing top plate by removing bolts around outside of housing.
5. Leaving engine fastened to top plate, turn it upside down so the impeller is on top.
6. Remove impeller bolt and lock washer.
7. Lift impeller upward. If impeller slides freely, proceed to (step 10).
8. Place two crowbars between impeller and housing on opposite sides. Pry impeller away from engine until it
loosens. Using a penetrating oil can help loosen a stuck impeller.
9. If the impeller does not loosen, obtain a 1” (25.4mm) longer bolt of the same diameter and thread type as
the impeller bolt. Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or
wheel puller against the bolt head and the impeller back-plate (near the blades), remove impeller from shaft.
10. Using a new impeller bolt and lockwasher, reinstall new impeller in reverse order.
11. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N.m) (see item 51 on page 15).
12. Reinstall engine onto housing in reverse order of removal.
13. Gas and oil (0.69 quart).
14. Reinstall spark plug wire.
Part No 890033
Form No F062306A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
Troubleshooting
Problem
Abnorm al vibration.
Possible Cause
· Loose or out of balance im peller or
loose engine
Solution
· Check im peller and replace if required.
Check engine
W ill not vacuum or has poor · dirty debris bag. Nozzle height set too
· Clean debris bag. Shake bag clean or
wash. Adjust nozzle height. Check for
hose kit cap. Unclog nozzle or exhaust.
Allow air to feed with debris
vacuum perform ance
high or low. Hose kit cap m issing.
Clogged nozzle or exhaust. Excessive
quantity of debris.
Engine will not start.
· Stop switch off. Throttle in off position.
Engine not in full choke position. O ut of
· Check stop switches, throttle, choke
position and gasoline. Connect spark
gasoline. Bad or old gasoline. Sparkplug plug wire. Clean or replace air filter. O r
wire disconnected. Dirty air cleaner
contact a qualified service person.
Engine is locked, will not pull · Debris locked in im peller. Engine
· See page 5. Contact a engine service
dealer for engine problem s
over.
problem .
Adjust nozzle height (See Nozzle height
fine adjustm ent for hard surfaces on
page 5
Nozzle scrapes ground in
lowest height setting.
Nozzle height out of adjustm ent
When servicing engine refer to specific manufacturers engine owner's manual. Engine warranty is covered by the
specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing
engine dealer. When contacting a dealer for service it is a good idea to have your engine model number available
for reference (See table page 3). If you cannot locate a servicing dealer in your area you can contact the
manufacturers national service organization.
To reach:
American Honda: 800-426-7701
WARRANTY CLAIM PROCEDURE
®
Should a BILLY GOAT machine fail due to a defect in material and/or workmanship, the owner should make a
warranty claim as follows:
•
•
•
The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY
GOAT Dealer.
The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the
invoice or receipt.
The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their
respective BILLY GOAT Distributor for their territory Attention: Service Manager. Any parts replaced under
warranty must be tagged and retained for 90 days. The model number and serial number of the unit must
be stated in the Warranty Claim.
•
•
The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.
The Technical Service Department at BILLY GOAT will study the claim and may request parts to be
returned for examination. BILLY GOAT will notify their conclusions to the distributor service manager from
whom the claim was received.
•
The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is
final and binding.
For online product registration go to www.billygoat.com
Part No 890033
Form No F062306A
12
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
MAINTENANCE RECORD
Date
Service Performed
Part No 890033
Form No F062306A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
Part No 890033
Form No F062306A
14
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
PARTS LIST
ITEM
KD612
Part No.
890305
KD512HC
Part No.
890023
K D512HCS
Part No.
890023
DESCRIPTIO N
Q TY
Q TY
Q TY
NO .
1
PRO DEBRIS BAG (service)
1
1
1
* Denotes
standard
hardware
item that
may be
purchase
d locally.
2
3
4
5
6
7
NUT LO CK (1/4 - 20 )
*8160001
*8041008
900054
7
8
1
*8160001
*8041008
900054
7
8
1
*8160001
*8041008
900054
7
8
1
SCREW C AP ( 1/4 - 20 x 1-1/2 HEX )
HANDLE ASS’Y (incl. item s 4(5),5(5),11(2),75(2),76)
AXLE HEIG HT ADJUST
890389
1
890389
1
890389
1
8
9
SCREW H ANDLE 5/16 - 18 x 1 - 3/4
CLAM P CABLE
*8041031
900407
2
2
*8041031
900407
2
2
*8041031
900407
2
2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
SCREW C AP 1/4 - 20 x 1 3/4
BAR BAG SUPPO RT
DO O R EXHAU ST ASS’Y (incl. item 62 )
PLATE TO P ASS’Y (incl. item s 29, 57, 65)
BO LT-CARRIAG E 1/4x3/4
*8041009
900039
890148
1
2
1
1
2
1
10
*8041009
900039
890148
1
2
1
1
2
1
10
*8041009
900039
890148
1
2
1
1
2
1
10
890402
890402
890402
*8024021
8172008
*8171002
*8024021
8172008
*8171002
*8024021
8172008
*8171002
W ASHER FLAT 5/16
W ASHER 1/4 FC ZP
BRACKET - HEIG HT ADJUSTM ENT
PLATE UPPER HEIG HT ADJUST
SPRING
TIRE - O NLY (PER ASSY)
PIN - HAIR CO TTER
890021
890005
900136
900507
900471
890019
*8024054
1
1
1
1
1
1
4
890021
890005
900136
900507
900471
890019
*8024054
1
1
1
1
1
1
4
890021
890005
900136
900507
900471
890019
*8024054
1
1
1
1
1
1
4
CABLE HEIG H T ADJUSTM ENT
BO LT - CARRIAG E 5/16 - 18 x 4 1/2
NUT LO CK 5/16 - 18 HEX
HANDLE LO W ER KD510
PLATE HANDLE SUPPO RT
LABEL DANG ER CUT FING ER
W ASHER FLAT CUT 5/16
*8160002
890346
900933
400424
*8171003
6
1
1 -2
2
*8160002
890346
900933
400424
*8171003
6
1
1 -2
2
*8160002
890346
900933
400424
*8171003
6
1
1 -2
2
2
2
6
NUT LO CK 5/16 - 18 THIN HT.
G RIP HANDLE
W HEEL ASS’Y (incl. item s 21)
W ASHER 0.75 “C”
*8161041
400570
900509
900997
4
2
4
400570
900509
900997
2
4
0 -1
900509
900997
4
0 -1
0 -1
SCREW SM 1/4x3/4 TYPE A
PLATE SKID (incl. item s 54)
SPACER IM PELLER
-
-
-
-
-
-
-
-
-
-
1
*8122082
890413
890616
4
1
1
890616
SCREW SELF TAPPING 10 - 24 x 1/2
NO ZZLE M AIN FR AM E ASS’Y (incl. one of item s 29,44,42)
PLUG
*8123086
890391
900146
890618
-
1
1
1
2
-
*8123086
890391
900146
890618
-
1
1
1
2
-
*8123086
890391
900146
890618
1
1
1
2
LINER HO LD PLATE
IM PELLER ASS’Y (incl. item s 49, 50, 51 )
900215
1
890615
1
890615
1
KEY
900162
400502
900154
890371-S
-
2
1
1
1
-
1
-
-
900162
400502
900154
890371-S
890614
-
2
1
1
1
1
-
-
-
4
15
8
900162
400502
900154
890417-S
890614
-
8024039
900732-S
890408
890359
*8172011
2
1
1
1
1
-
4
1
4
W ASHER LO C K 3/8 TW ISTED TO O TH
SCREW C AP 3/8 -24 x 1 G R 8 (TO RQ .50 FT-LBS)(68N.m )
HO USING ASS’Y (incl. item s 12, 14, 15, 16, 66)
ENG INE HO NDA 5.5 H.P. G C160
ENG INE BRIG G S & STRATTO N 6 H.P. Q U ANTU M IC
BO LT CARRIAG E 5/16-18x3/4"
890622
-
54
55
56
57
58
59
60
61
62
63
64
65
66
-
-
LINE PVC
-
SCREW C AP 3/8 - 1-1/2 TAPTITE
SCREW C AP 1/4 - 20 x 1/2 HW H
W ASHER FLAT 1/2 SAE
SCREW SO CKET HD. 5/16 - 18 x 3/4 G R. 8
HG T ADJUST ASSY (INCL. ITEM S 18, 20, 22, 23)
1/2-13 CAP NUT NP W /PATCH
LABEL DANG ER FLYING M ATERIAL
LABEL DO NO T FILL W HEN ENG INE IS HO T
CO NNECTO R BAG Q UICK
LABEL READ O W NER'S M ANUAL
LABEL EAR/EYE BR EATH ING
890408
890359
*8172011
4
15
8
890408
890359
*8172011
15
8
890013
890530
810736
400268
890176
890301
890254
1
4
1
1
1
1
1
890013
890530
810736
400268
890176
890301
890254
1
4
1
1
1
1
1
890013
890530
810736
400268
890176
890301
890254
1
4
1
1
1
1
1
Part No 890033
Form No F062306A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
KD Owner’s Manual
BRUSH CUTTER
FORCE BLOWER
AERATOR
If you liked this product please feel
free to view our full line of quality lawn
care, renovation, and debris removal
products at www.billygoat.com
QL VACUUM
MULTI VACUUM
POWER RAKE
Part No 890033
Form No F062306A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|