Chauvet Marine Radio DMX512 User Manual

Snapshot

OK on Dimmer

Outdoor OK

LED Mushroom

Sound-Activated

DMX512

Master/Slave

115V/230V Switch

Replaceable Fuse

User-Serviceable

USER MANUAL

5200 NW 108th Avenue, Sunrise, FL 33351 U.S.A.

(800) 762-1084 – (954) 577-4455

FAX (954) 929-5560

www.chauvetlighting.com

Download from Www.Somanuals.com. All Manuals Search And Download.

1. BEFORE YOU BEGIN

What is Included

1 x LED Mushroom

Power Cord

Warranty Card

User Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power

This fixture has an auto-switching power supply that can accommodate a wide range of input

voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage

you are applying is within the range of accepted voltages. This fixture will accommodate between

100V and 240V AC 50-60 Hz. All fixtures must be powered directly off a switched circuit and cannot

be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is

used solely for a 0–100% switch.

Safety Instructions

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance of this

product.

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

Always make sure that you are connecting to the proper voltage, and that the line voltage you are

connecting to is not higher than that stated on the decal or rear panel of the fixture.

This product is intended for indoor use only! (If applicable)

To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no

flammable materials close to the unit while operating.

The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Always disconnect from power source before servicing or replacing lamp or fuse and be sure to

replace with same lamp source.

Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use

its carrying handles.

Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher

than this.

In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

Never connect the device to a dimmer pack.

Make sure the power cord is never crimped or damaged.

Never disconnect the power cord by pulling or tugging on the cord.

Avoid direct eye exposure to the light source while it is on.

Do not daisy chain power to more than 37 units @ 120V and 70 @ 230V.

Caution!

There are no user-serviceable parts. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact

CHAUVET® at: 954-577-4455.

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

2. INTRODUCTION

Features

2-channel DMX-512 LED derby effect

Continuous rotation or back and forth motor control

Built-in automated programs via master/slave or DMX

Built-in sound activated programs via master/slave or DMX

Additional Features

High-power, 3W (730mA) LEDs

Linkable with Kinta™ X and Double Derby™ X

Additional power output: max 37 units @ 120V and 74 units @ 230V

DMX Channel Summary

CHANNEL FUNCTION

Control/Operating Mode

Motor rotation

Product Overview

DMX Out

Dipswitches

DMX In

Sound

sensitivity

adjustment

Power

Power link

out

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Overview con’t

Hanging/mounting

bracket

Bracket

adjustment

knob

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

3. SETUP

Disconnect the power cord before replacing a fuse and always

replace with the same type fuse.

Fuse Replacement

With a flat-head screwdriver wedge the fuse

The fuse is located

inside this

compartment.

Remove using a flat

head screwdriver.

holder out of its housing. Remove the damaged

fuse from its holder and replace with exact

same type fuse. Insert the fuse holder back in

its place and reconnect power.

Data Linking

You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller

or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The

combined number of channels required by all the fixtures on a serial data link determines the number

of fixtures the data link can support.

Important:

Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485

standard no more than 32 devices should be connected on one data link. Connecting more than 32

fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in

deterioration of the digital DMX signal.

Maximum recommended serial data link distance: 500 meters (1640 ft.)

Maximum recommended number of fixtures on a serial data link: 32 fixtures

Data Cabling

To link fixtures together you must obtain data cables. You can purchase CHAUVET®-certified DMX

cables directly from a dealer/distributor or construct your own cable. If you choose to create your own

cable please use data-grade cables that can carry a high quality signal and are less prone to

electromagnetic interference. If you are unfamiliar with DMX, download the DMX Primer from

www.chauvetlighting.com .

CAUTION

Do not allow contact between the common and the fixture’s chassis ground. Grounding the common

can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to

verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.

Master/Slave Linking

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector

of the first fixture.

2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,

proceed to connect from the output as stated above to the input of the following fixture and so on.

Often, the setup for Master-Slave

and Standalone operation requires

Slave

Master

that the first fixture in the chain be

initialized for this purpose via either

settings in the control panel or DIP-

switches. Secondarily, the fixtures

that follow may also require a slave

setting. Please consult the

“Operating Instructions” section in

this manual for complete

instructions for this type of setup

and configuration.

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting

Orientation

This product may be mounted in any safe position as long as there is adequate room for ventilation.

Rigging

Hanging Clamp

It is important never to obstruct the fan or vents pathway. Mount the

product using, a suitable “C” or “O” type clamp. Adjust the angle of

the fixture by loosening both knobs and tilting the fixture. After finding the

desired position, retighten both knobs.

When selecting installation location, take into consideration lamp

replacement access and routine maintenance.

Safety cables must always be used.

Note!

Never mount in places where the fixture will be exposed to rain, high

humidity, extreme temperature changes or restricted ventilation.

Clamp is sold separately.

Do not mount more than 3 fixtures with the X-bracket.

4. OPERATING INSTRUCTIONS

Standalone Mode (Sound-Active, Auto Mode):

This mode allows a single unit to run to the beat of the music.

1) Set dipswitches position to Sound Active or Auto Mode.

Mode

Dipswitches

Sound Active

1-10= Off

2) The unit will react to the low frequencies of music via the internal microphone in Sound Active

mode

3) Use the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in

Sound-Active mode. Turning the knob counterclockwise decreases the sensitivity; turning the

knob clockwise increases the sensitivity.

DMX Mode

This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with

DMX, please read the DMX Primer on page 13.

1) Set dipswitches position to DMX mode.

Mode

Dipswitches

DMX

10= On

2) Use dipswitches 1-9 to set the DMX address.

DMX Channel Values

CHANNEL VALUE

FUNCTION

Control/Operating Mode

No function

LED’s on

000 ó 014

015 ó 100

101 ó 255

Auto

Motor Rotation

001 ó 085

086 ó 170

171 ó 255

Counter-clockwise motor rotation (Slow ~ Fast)

Clockwise motor rotation (Slow ~ Fast)

Motor rotation right-to-left-to-right (Slow ~ Fast)

-Note: Channel 1 will override the motor control channel (channel 2)

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Starting Address

This DMX mode enables the use of a universal DMX controller device. Choose start addresses so that the

channels used do not overlap, and note the start address selected for future reference. Set the start address

using the group of DIP switches located usually on bottom of the fixture. Each dip switch has an associated

value. Adding the value of each switch in the ON position will provide the start address. Figuring out which

switches to toggle ON given a specific start address can be accomplished by determining which switch values

will add up to the address value, and turning these switches on. Do so by doing the following:

1) Determine the largest value switch that is less than the start address. Turn this switch on.

2) Subtract the value of the switch you just turned on from the starting address number.

3) Determine the largest value switch that is less than the remainder from the previous subtraction. Turn this

switch on.

4) Subtract the value of the switch you just turned on from the remainder of the previous subtraction.

5) Repeat steps three and four until you have a remainder of zero.

EXAMPLE STARTING ADDRESS

Address 10

Switch # 4

Switch # 2

Total

= 8

= 2

9 8 7 6 5 4 3 2 1

= 10

OFF

Address 24

Switch # 5 = 16

Switch # 4 = 8

9 8 7 6 5 4 3 2 1

Total

= 24

OFF

Resolving address

using simple math.

233 – (128) = 105, Turn ON Dip # 8

DIPSWITCH (DMX VALUE)

105 – (64) = 41, Turn ON Dip # 7

41 – (32) = 9, Turn ON Dip # 6

9 – (8) = 1, Turn ON Dip # 4

1 – (1) = 0, Turn ON Dip # 1

1 1

2 2

3 4

Address 233

4 8

5 16

6 32

7 64

8 128

9 256

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

DMX Quick Reference Chart

DMX Address Quick Reference Chart

Dip Switch Position

DMX DIP

SWITCH SET

0=OFF

1=ON

X=OFF or ON #6 0

#1 #2 #3 #4 #5

#9 0

#8 0

#7 0

32 64 96 128 160 192 224 256 288 320 352 384 416 448 480

1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481

2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482

3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483

4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484

5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485

6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486

7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487

8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488

9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489

10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490

11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491

12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492

13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493

14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494

15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495

16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496

17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497

18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498

19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499

20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500

21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501

22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502

23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503

24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504

25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505

26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506

27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507

28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508

29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509

30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510

31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

DMX Address

Dip Switch Position

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

5. APPENDIX

General Maintenance

To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage

and environment are contributing factors in determining frequency. As a general rule, fixtures should

be cleaned at least twice a month. Dust build up reduces light output performance and can cause

overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off

fixture before conducting maintenance.

Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust

collected on external vents and internal components. Clean all glass when the fixture is cold with a

mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply

solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical

surfaces until they are free of haze and lint.

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates:

damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s

optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean

the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Return Procedure

Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.

Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).

Products returned without an RMA # will be refused. Call CHAUVET® and request RMA # prior to

shipping the fixture. Be prepared to provide the model number, serial number and a brief description

of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from

inadequate packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own

discretion to repair or replace product(s). FedEx packing or double-boxing are recommended.

Note:

If you are given an RMA #, please include the following information on a piece of

paper inside the box:

1) Your name

2) Your address

3) Your phone number

4) RMA #

5) A brief description of the symptoms

Claims

Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be

reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and

submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim

for items such as missing component/part, damage not related to shipping, and concealed damage,

must be made within seven (7) days of receiving merchandise.

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

General Troubleshooting

Applies to

Foggers

& Snow

Dimmers

& Chaser

Symptom

Solution(s)

Lights

Controllers

Auto shut off

Check fan thermal switch reset

Beam is very dim or

not bright

Clean optical system or replace lamp

Check 220/110v switch for proper setting

Breaker/Fuse keeps

blowing

Check total load placed on device

Device has no power Check for power on Mains.

Check device’s fuse. (internal and/or external)

Fixture is not

responding

Check DMX Dip switch settings for correct addressing

Check DMX cables

Check polarity switch settings

Fixture is on but

there is no

movement to the

audio

Make sure you have the correct audio mode on the

control switches. If audio provided via ¼” jack, make

sure a live audio signal exists

Adjust sound sensitivity knob

Lamps cuts off

sporadically

Possible bad lamp or fixture is overheating.

Lamp may be at end of its life.

Light will not come

on after power failure before the electronics in the fixture can kick start it

again, wait 5 to 10 minutes before powering up

Some discharge lamps require a cooling off period

Loss of signal

Use only DMX cables

Install terminator

Note: Keep DMX cables separated from power cables

or black lights.

Moves slow

No flash

Check 220/110v switch for proper setting

Re-install bulb, may have shifted in shipping

No laser output

No light output

Bounce mirror motor may have shifted during shipping,

readjust

Check slip ring & brushes for contact

Install bulb

Call service technician

Relay will not work

Check reset switch

Check cable connections

Remote does not

work

Make sure connector is firmly connected to device

Stand alone mode

All Chauvet lighting fixtures featuring stand-alone

functions do not require additional settings, simply

power the fixture and it will automatically enter into this

mode

If you still have a problem after trying these solutions, contact CHAUVET® Technical Support.

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical Specifications

WEIGHT & DIMENSIONS

Length ................................................................................................................................................................ 12 in (306 mm)

Width ................................................................................................................................................................. 8.1 in (206 mm)

Height ................................................................................................................................................................ 8.7 in (221 mm)

Weight .................................................................................................................................................................5.4 lbs (2.4 kg)

POWER

Autoswitching........................................................................................................................................100-240 VAC 50/60 Hz

Fuse..........................................................................................................................................................................F 1 A 250 V

Power Consumption .......................................................................................................................18 W (0.2 A) max @ 120 V

Inrush Power.....................................................................................................................................................(0.5 A) @ 120 V

Power Consumption .......................................................................................................................19 W (0.1 A) max @ 230 V

Power Output ................................................................................................... 37 units max @ 120 V, 74 units max @ 230 V

LIGHT SOURCE

LED......................................................................................................3 x 3 W (730 mA) (1 Red, 1 Green, 1 Blue) 50,000 hrs

PHOTO OPTIC

Coverage Angle ...................................................................................................................................................................130°

THERMAL

Maximum ambient temperature.............................................................................................................................104°F (40°C)

CONTROL & PROGRAMMING

Data input.................................................................................................................................. locking 3-pin XLR male socket

Data output............................................................................................................................. locking 3-pin XLR female socket

Data pin configuration................................................................................................................pin 1 shield, pin 2 (-), pin 3 (+)

Protocols ..........................................................................................................................................................DMX-512 USITT

DMX Channels..........................................................................................................................................................................2

ORDERING INFORMATION

LED Mushroom ..............................................................................................................................................LEDMUSHROOM

WARRANTY INFORMATION

Warranty.................................................................................................................................................2-year limited warranty

World Wide

General Information CHAUVET

5200 NW 108th Avenue

Sunrise, FL 33351

voice: 954.577.4455

fax:

toll free:

954.929.5560

800.762.1084

Technical Support

World Wide Web

CHAUVET

5200 NW 108th Avenue

Sunrise, FL 33351

voice: 954.577.4455 (Press 4)

fax:

954.929.5560 (Attention: Service)

www.chauvetlighting.com

LED Mushroom User Manual

Rev. 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Black Box Computer Hardware 5250 User Manual
Black Box Network Hardware 4 Port RJ 45 Modem Splitter RS 232 on RJ 45 User Manual
Black Decker Fan BDHT5016 User Manual
Black Decker Work Light 90518422 User Manual
Blomberg Refrigerator SOM 9650 User Manual
Bowers Wilkins Portable Speaker AS2 User Manual
Bushnell Binoculars 13 7507 User Manual
Bushnell Telescope 78 7325 User Manual
Campbell Hausfeld Cordless Drill PL154699 User Manual
Casio Watch MA1011 EB User Manual