User's Guide
™
eVo2i
Two Channel Integrated Audio Amplifier
Bel Canto Design, LTD.
212 Third Avenue North
Minneapolis, MN 55401
Phone: (612) 317.4550
Fax: (612) 359.9358
©2002-2004 Bel Canto Design, LTD
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
eVo2i box contents include the following:
1 (one) - eVo2i Integrated Amplifier
1 (one) - eVo2i User’s Guide
1 (one) - Power cord
1 (one) - Remote Control
Carefully unpack each piece and check
for shipping damage. If there is any
damage, or if anything is missing,
please contact your dealer, distributor or
Bel Canto Design.
IMPORTANT: Save all packing
materials as the packing is spe-
cially designed to protect the
unit during transportation or shipping. If
the packaging becomes lost or dam-
aged, please contact your dealer, dis-
tributor or Bel Canto before attempting
to transport your unit.
Power Connection
The power supply on the eVo2i is preset
for the proper national voltage. The
power cable should have the correct
plug for your local power system. If you
believe this to not be true, please con-
tact your dealer immediately.
This integrated amplifier, like any electri-
cal component, can be dangerous and
cause injury unless correct handling pro-
cedures are observed and used. Before
powering this preamplifier it is neces-
sary to read and follow proper setup
and procedures.
Warning!
Do not connect power to this
preamplifier yet!
© 2002-2004 bel canto design, Ltd.
page 3
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement and Initial Setup
Because the eVo2i runs cool it can be
Single Ended RCA and Balanced XLR
connectors are available. XLR jacks
allow balanced hookup using the stan-
dard pin configuration:
placed in many system locations without
compromise. We do not recommend
placing weights or other objects directly
on the eVo2i. This may mar or scratch
the chassis finish. Do not use harsh
chemicals when cleaning the outside of
your eVo2i.
Pin 1 Ground
Pin 2 Input +
Pin 3 Input -
IMPORTANT: Make all connections before powering your unit.
Design Features
• The elegant simplicity of the signal path
• Efficiency >90% insures cool operation.
• THD and IMD <0.05%
and gain stage allows the eVo2i to pre-
serve audio signal quality. Audio Grade
decoupling capacitors and resistors, star
grounding and careful signal routing insure
that low-level signals are preserved.
• Damping Factor >100
• High thermal stability in all stages
• Fully regulated, low noise supplies for all
analog stages
• Input processing provides one balanced
XLR connection, three RCA jack connec-
tions and Tape In. Tape Output is an RCA
output with an active audio-grade buffer to
isolate the internal signal bus from the tape
output. Line out RCA connection offers flexi-
bility of use with a sub woofer, external
amplifier for bi-amping or outboard signal
processor.
• Soft clipping with uncompromised low
level distortion performance
• Ultra-low power dissipation for ‘green’
amplification
• Protection circuitry outside signal path
• Programmable features allow you to dis-
able (except TAPE), name and set volume
for listening and soft mute levels for ALL
inputs individually
• The volume control is a precision analog
stepped attenuator controlled by a micro-
controller. This device provides extremely
low noise and distortion coupled with high
accuracy. The sonic quality is superior to
the best potentiometers and insures no
wear.
• The eVo2i powers on in Soft Mute Mode.
Soft Mute Mode is a fully adjustable setting
that also can be selected as a muting
option during regular listening.
• High efficiency Digital Power Processing
eVo power amplifier.
© 2002-2004 bel canto design, Ltd.
page 4
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
Conditioning
The eVo2i’s sonic performance will start
to stabilize after 100 hours of continu-
ous power up.
Front Panel and Remote Controls
Volume Up:
Balance Left: (available from the
remote only)
Increases the output level in 0.5 Decibel
(dB) steps from 0.0 to 100.0.
Shifts balance left in 0.5dB steps. It is
also used to scroll left in the setup menu.
Volume Down:
Decreases the output level.
HARD MUTES OUTPUT, DISABLES DISPLAY
AND CONTROLS
VOLUME AND BALANCE CONTROLS
AND NAVIGATION FOR SETUP MENUS
INPUT SELECTION
TOGGLES DISPLAY ON/OFF
CYCLES THROUGH INPUTS
PRESS 7 TIMES TO
ACCESS SETUP MENUS
SELECTS TAPE INPUT
© 2002-2004 bel canto design, Ltd.
page 5
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
Balance Right: (available from the
MAIN:
remote only)
Cycles through the main inputs. It is also
used to scroll to the left in the setup
menu.
Shifts balance right in 0.5dB steps. It is
also used to scroll right in the setup
menu.
LOOP: (available from the remote only)
This is used to cycle through the inputs.
INPUT:
MUTE:
The eVo2i starts up in Soft Mute. This
level is 20dB below the displayed vol-
ume level. When MUTE is first pressed it
goes to the Soft state, pressing MUTE
again within 3 seconds will fully MUTE
the outputs.
On the remote the Numbered Buttons (1-
5) allow you to select between the active
inputs. From the remote, you can cycle
through inputs using the LOOP button.
From the front panel, you can cycle
through inputs by pressing the MAIN
button. When switching between inputs,
the eVo2i will quickly ramp down the
volume, switch inputs, then quickly ramp
back up to the programmed volume set-
ting.
ENTER:
This control button is pressed and held
on the front panel or pressed 7 times on
the remote to enter into the menu setting
functions described below. It is also used
to enter into specific modes within the
menu system.
VOLUME CONTROL
AND UP/DOWN KEYS*
PRESS ENTER AND HOLD TO
TAPE INPUT SELECT*
ACCESS SETUP MENU*
SOFT AND FULL
MUTE FUNCTIONS
MUTES OUTPUT, DISABLES DISPLAY
AND CONTROLS
MAIN INPUT SELECT*
*ALSO USED FOR NAVIGATING THE SETUP MENU
© 2002-2004 bel canto design, Ltd.
page 6
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
TAPE:
STANDBY:
On both the remote and the front panel,
the TAPE select between the active main
input or the tape input
When in STANDBY mode the red LED is
engaged, the display is off and the out-
puts are muted. The unit remains
warmed up and ready for use when
taken out of standby.
It is also used to scroll to the right in the
setup menu.
eVo2i Back Panel
Inputs 1 to 4
the Main input selector is be routed to
the buffered Tape Output.
Standard line level inputs. Input 1 is bal-
anced and may be used with unbal-
anced sources using an RCA to XLR
adapter.
Line Out
Line Out is a buffered preamplifier out-
put which tracks the volume setting on
the front panel. This can be used to
drive the line level input on a subwoofer,
for example.
Tape In/Tape Out
Tape loop function: Tape In selected
routes the Tape In jacks to the main out-
puts. The main input 1-4 selected with
© 2002-2004 bel canto design, Ltd.
page 7
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
Loudspeaker Connection
Connect loudspeakers to the outputs of the
would result in one of the red (positive) out-
puts being connected to ground and cause
the amplifier to go into protection mode and
shut itself off.
eVo amplifier using the 5-way binding posts
located the rear of the amplifier. The red or
black center plug in the output post can be
removed for use with banana type connec-
tors (all non CE countries). Do not connect
speaker terminals to a ground connection.
Make certain that no connection from the
output terminals is made to a chassis or
earth ground.
The Anti-Phase operation of the outputs
Setup Menu Options
A) INPUTS CONFIGURATION Menu
cator left or right using the LEFT/RIGHT
keys and use the UP/DOWN keys to
scroll through capital and lower case let-
ter, numbers 0-9 and a SPACE.
This menu is used to customize the input
options.
It is used to set:
You can use the SPACE to separate words
and numbers or to center short names like
CD. Press Enter to exit this menu mode.
1) Input Function
2) Input Name
3) Initial Volume level
4) Soft Mute level
3) The third menu level is used to set the
Initial Volume level.
1) The first level of this menu is used to set
the INPUT FUNCTION. The options are
Stereo or Disabled.
Press ENTER and use the UP/DOWN
keys to set the default level when coming
out of STANDBY. Press ENTER to exit this
menu mode
Change these settings by scrolling left or
right to the desired input and pressing
ENTER to change the setting. Use the
UP/DOWN keys to scroll through the set-
ting options. Disable unused inputs.
.
4) The fourth menu level is used to set the
Soft Mute Level.
This is preset to -20 dB. This is generally a
good soft mute level.
Press ENTER to exit this menu mode.
If you wish to change this for a given
input then press ENTER and use the
UP/DOWN keys to scroll to a different
setting.
2) The second level of this menu is used
for changing the Name of a given input.
To change an input name press ENTER
and you will see an under-bar indicator
for each of the 8 characters that can be
used for naming the input. Scroll the indi-
Press Enter to exit this menu mode.
© 2002-2004 bel canto design, Ltd.
page 8
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu Options
B) SAVE CONFIG ? Menu
Press ENTER to save your configuration
and exit this menu mode.
This is used to Save the Setup Changes
made in the menu system.
C) ERASE CONFIG ? Menu
Be sure to use this to store the changes
when you are satisfied with your setup.
Use the UP/DOWN keys to toggle
between YES or NO and save the menu
settings.
This is used to Restore the Factory
Default menu settings.
Use the UP/DOWN keys to toggle to
YES or NO.
Saving the settings will insure that your
changes are active even if power is
removed from the eVo2i.
Press ENTER to erase your configuration
and restore the factory settings.
Warning: This operation resets all of
your custom settings.
© 2002-2004 bel canto design, Ltd.
page 9
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power output per channel into 8 ohms • 120 watts <1% THD+N
Power output per channel into 4 ohms • 200 watts <1% THD+N
Bandwidth: +/- 3dB •1Hz-80KHz
Volume setting for unity gain • 84.0 (Inputs to Line output)
Input for full output with volume set to 84.0 • 1.9V RMS
Signal to Noise Ratio @ 1 watt out • >96 dB A weighted, 20 kHz
Distortion @ 1 watt/1kHz • <0.05%
Damping Factor • >100
Input configuration and impedance,single-ended/balanced • 10 Kohm/20 Kohm
Gain • 16 dB Preamplifier section, 23 dB Amplifier section
Standby power • 15 Watts
Maximum power • 500 Watts
Input Overload, Single Ended/Balanced • 10V RMS
Power Requirements • 100-120 VAC 50-60 Hz or 220-240 VAC 50-60 Hz
Dimensions • 17.5" W x 14.5" D x 4.5" H (445 mm x 368 mm x 114 mm)
Weight • 37 lbs. (13 kg)
© 2002-2004 bel canto design, Ltd.
page 10
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2002-2004 bel canto design, Ltd.
page 11
eVo2i User’s Guide rev081104
Download from Www.Somanuals.com. All Manuals Search And Download.
Bel Canto Design, LTD.
212 Third Avenue North
Minneapolis, MN 55401
Phone: (612) 317.4550
Fax: (612) 359.9358
©2002-2004 Bel Canto Design, LTD
eVo2i is a trademark of Bel Canto Design, LTD
Download from Www.Somanuals.com. All Manuals Search And Download.
|