LCD COLOUR TELEVISIONS
15LB250MID
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
1
LCD panels are produced with state-of-the-art technology. However, there may be black or
lit spots on the screen under certain circumstances. That does not mean that the product is
faulty.
1.1 Cleaning the screen and cabinet...
After powering off, wipe the screen and the cabinet clean with a soft and dry cloth. We
recommend that you do not use patented polishes or solvents to clean the screen or cabinet
since they may cause damage.
1.2 Disposing of your TV at the end of service life...
The cold cathode fluorescent lamp found in your LCD screen contains a very small amount of
mercury. Once your TV set has completed its physical life, please dispose of it in accordance
with local government regulations or leave it at a recycling centre.
1.3-Superior features of your integrated digital television
This television can receive and process all analogue and digital broadcasts. This television set
has an integrated digital and analogue receiver. The digital receiver unit processes the signals
coming from digital transmitters and converts them into superior sound and image quality. TV
Guide (valid for digital broadcasts only) informs you about changes in the program list briefly
and provides program lists of all digital broadcasts for a number of forthcoming days. You
can display detailed information about each program by pressing a single button if this feature
is supported by the broadcaster. This television has a comprehensive and user friendly menu
configuration.
1.4-Receiving digital broadcasting channels
You will need an outdoor aerial to receive digital broadcasts. Contrary to the analogue
broadcasts, all digital broadcasts may not have their own transmission frequency. Instead,
various digital broadcasts channels are gathered in regional or national groups called
bouquets. You can find current transmission data from teletexts of various broadcasters or
from TV guide or from the internet.
Note:You should check your postcode to make sure that you are in a freeview coverage area.
(www.freevıew.co.uk.)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Features of your new television
We would like this product, which has been manufactured in modern facilities in accordance
with total quality principles, to offer you the best performance. Therefore, we would like you to
read this entire manual carefully before you use your product and keep it for future reference.
2.1-Special Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Available for cable broadcasts
SCART connection
Audio/Video PHONO inputs
PC connection (*)
Stereo from AV
Low energy consumption
Automatic switch-off feature that can be programmed between 15 and 120 minutes
8 pages Teletext
Fasttext
Toptext (*)
MHEG 1.06
EPG (Electronic Program Guide) feature
CI slot input
Software upgrade by air transmission
6 Digital Favorite channel lists
A clearer picture made possible with a Digital Comb Filter (*)
DNR Noise reduction
Manual fine tuning
100 Analogue Program memory
1000 Digital Program memory
Returning to the last viewed program by single button (SWAP)
Infrared remote control equipped with all functions
Ability to watch NTSC video playback via scart input
Easy performance of the processes with the advanced menu system
4:3, 16:9, Auto picture formats
16:9 picture format that can be selected with single button
Automatic broadcast detecting system by means of WSS feature
Renaming, deleting, skipping and relocating the programs.
Ability to operate both with 230 V mains power and 12 V adaptor (*)
(*): These features are optional and they are not available on all models.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Important Safety Instructions
This symbol is used to warn the user about the “dangerous voltage” contained
inside the housing of the product that may create a risk of electrical shock.
This symbol is used to remind the user important usage and service instructions
supplied with the television.
1) Please READ the operating
•
Never install the TV into closed places
such as bookcases or cabinets unless
adequate ventilation is provided.
instructions before using
the TV for the first time.
MANUAL
2) Please observe the
instructions contained in
the Operating Instructions.
3) Please consider all warnings.
4) MAKE SURE that all
power connections
(extension cables and the
connections between the
external equipment have
been made properly and
in accordance with the manufacturer’s
instructions. Before making or changing
the connections, power off the TV and
unplug the mains connection plug.
8) DO NOT COVER the
ventilation openings of
the TV with items such
as newspapers, table-
clothes, curtains, etc.
Overheating causes
5) If you have any doubts regarding the
installation, operation or safety of the TV,
please REFER to the retailer.
damage and shortens the service life of
the TV.
9) Your TV may be damaged
if you place it under
6) BE CAREFUL with glass panels and
covers on the TV. The screen glass
may break and cause serious injuries if
something hits it.
direct sunshine or close
to a heater. Please
abstain from using the
product in very hot or
7) To ensure adequate ventilation, please
leave a clearance area of at least 10 cm
around the television. This clearance
prevents the TV from overheating and
consequently causing damage.
humid locations or in places where the
temperature is likely to decrease below
5°C (41°F). DO NOT PLACE on or near
the TV any hot objects or items with
open flame such as candles or any night
lamps. The high temperature can melt
plastic parts and cause a fire.
•
Using the device in dusty environments
should also be avoided.
Never block the slots and openings by
placing the TV on a bed, sofa, pillow or
other similar surfaces.
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.
10) Never operate your
TV close to water.
television by means of the lighter
cable in a car, then use the cable
supplied with the product. Using a
different cable may damage your
appliance.
Operating your TV,
for example, near a
bathtub, washbasin,
wet basement and swimming pool can
cause fire or electric shock.
Note 2: If your device has an adaptor,
then use the adaptor and AC mains
lead supplied with your product. Do
not use defective sockets. Make sure
that the plug is firmly inserted into
the socket. If the plug remains loose,
then it can cause fire due to arcing.
Refer to an electrician to have your
socket replaced.
•
Do not allow your TV to get wet. Never
pour any liquids onto the TV. Do not
operate your TV if
any solid or liquid
substance enters into
it. This can cause
electric shock and your
TV may be damaged. Have it checked
immediately by qualified personnel.
13) Make sure that the mains
lead is not stepped on and
that there is no bending
•
Keep open flame sources (such as
candles) away from TV in order to avoid
risk of fire.
at the plug sections, plug
heads and TV output point.
11) DO NOT USE
headphones at
14) Use only the add-ons/
accessories specified by the
manufacturer.
extremely high volume
levels since this may
cause permanent loss of
hearing.
15) Use only brackets or stands
specified by the manufactury
or sold Place your device
on a level surface.
12) Operate your TV only in
the 230 V 50Hz voltage
range. Use the AC mains
lead supplied with the
product. If your TV is
a grounded (Class I)
product, then it must be
connected to an earthed
socket.
16) Unplug the mains lead
during thunderstorms or
when you will not use your
TV for a long period of time.
•
The socket into which you plug in the
AC mains lead or the adaptor must
be within easy reach.
Turn off your device with the ON/OFF
button and then unplug it in order to
disconnect it from mains.
•
Note 1: If you would like to operate your
4
Download from Www.Somanuals.com. All Manuals Search And Download.
17) Consult authorised
21) Do not dispose of your TV
with regular household waste.
Observe local laws and
service personnel for
service requirements.
Never attempt to
regulations for disposal.
repair the TV yourself.
Opening the cabinet
Note 1: This is a Class A product.
During operation, the TV can cause radio
interference. In this case the user may
have to remedy this. Please contact your
specialist dealer.
can expose you to dangerous voltages
or other hazardous situations. Service is
required in situations such as damage
to the mains lead of the TV or its plug,
water spills or substances falling into
the TV, the TV is subjected to rain or
moisture, it does not operate normally or
it is dropped.
Note 2: Electromagnetic fields can cause
temporary performance degradation. This
can be distinguished as noise in the image.
18) Wipe the TV cabinet
Note 3: Tighten the screws that are used
to connect the wall mount kit by 1 Nm
(10kgfcm) maximum.
clean with a soft and dry
cloth. Wipe dust from the
screen gently with a soft
cloth. Stubborn stains
Note 4: Your television can operate with
220V AC or 12V DV power supply. However,
do not connect 220V AC and 12V DC power
supplies to your television at the same time.
Otherwise, your television can get damaged.
can be cleaned with a
cloth slightly moistened
with soap and lukewarm water. Never
use solvents such as thinner or gasoline
for cleaning. Unplug the AC mains lead
from the socket when cleaning the TV.
Otherwise, there is the risk of electric
shock.
Note 5: Do not use any power supply
generating different voltages other then the
12V DC when operating your television with
DC power supply or vehicle battery.
19) Do not dispose of the
batteries in fire.
Note 6: When you are operating your
television in a vehicle and the vehicle is not
running, avoid keeping it turned on for long
periods since this may cause the vehicle
battery run flat.
•
Do not short circuit,
dismantle or overheat
the batteries. There is
the risk of explosion
if the batteries are not replaced
correctly. Replace only with the
same or equivalent type batteries.
20) Disposing of the exhausted
batteries:
Dispose of the exhausted
batteries in accordance with
the local laws and regulations in
order to protect our environment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
22) Connection of mains Cable
Always use the mains cable supplied. First of all insert the mains cable into the input panel of
the CTV, and only there after into the mains supply socket.
23) ELECTRICAL CONNECTIONS
For your own safety read the following instructions carefully before attempting to replace the
moulded mains plug. Please check the type of mains lead supplied with your television and
refer to the appropriate information below.
As the colours in the mains lead of this
appliance may not correspond with
IMPORTANT
the coloured markings identifying the
terminals in your plug, proceed
as follows:
The wire which is coloured blue or
black must be connected to the
The wires in the mains lead are coloured
in accordance with the following code:
Blue - Neutral
Brown - Live
terminal which is marked with the
letter N or coloured black.
The wire which is coloured brown or red must be
connected to the terminal which is marked with the letter
L or coloured Red.
5 A
No connection is to be made to the Earth terminal of the
plug.
If a 13 Amp (BS1363) Plug is used, fit an ASTA
apporoved 5 A fuse
If your product is fitted with a moulded plug which
requires replacement please cut off and dispose of it
safely, then rewire as shown in the diagram to the left.
BLUE
(Neutral)
As the colours in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured green and yellow must
be connected to the terminal which is marked with
the letter E, or by the earth symbol, or coloured
green or green and yellow.
IMPORTANT
The wires in the mains lead are coloured
in accordance with the following code:
Blue - Neutral
Brown - Live
Yellow/Green - Earth
The wire which is coloured blue or black must be
connected to the terminal which is marked with the
letter N or coloured Black.
5 A
The wire which is coloured brown or red must be
connected to the terminal which is marked with the
letter L or coloured Red.
If a 13 Amp (BS1363) Plug is used fit an ASTA
approved 5 Amp fuse.
If your product is fitted with a moulded plug which
requires replacement please cut off and dispose of it
safely, then rewire as shown in the diagram to the left.
•
•
•
•
•
•
Cover a table with a soft towel (or other protection to prevent damage to the TV or table)
Carefully lay the T.V. front down on the table
24)
position the T.V. table stand so that it hangs over the edge of the table
Remove the screws that hold the stand to the T.V.
Remove the stand.
Attach any new brackets before lifting T.V. back up.
Note: Keep removed stand and screws safely for future use.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Start
Remove your television carefully from its
box. You can keep the packaging of your
television to use in future.
Note 1: Your TV will switch to the stand-by
mode in five minutes if there is no broadcast
signal from aerial.
3power on your television, press any
ical key or P+ or P- keys on the
e control.
Items supplied with your television
Mains lead (*)
Adaptor (*)
Remote control
2 batteries
If you are not going to use your
ion for a long time, unplug its power
cable from the socket.
Note: The Scart, VGA (*) and PHONO
cables are not supplied with the
device.
(*) These features are optional and may not
be available on all models.
Initial power on and performing
settings
To set up your television, read the sections
on the TV controls and making the channel
settings.
4.3-Batteries
Open the lid of the battery compartment
and make sure that you have placed the
batteries in the correct direction. For this
remote control, UM-4, IEC R03 or AAA 1.5 V
batteries are suitable.
Do not throw your old batteries into the fire,
discard them in a dedicated waste area for
this purpose.
4.1-Aerial connection
If you use a 75 Ohm coaxial cable (round
cable) as an aerial cable, connect the aerial
plug directly to the aerial input located on
the TV.
Do not mix used batteries with new ones or
different types of batteries together.
Motorized vehicles, energy lines and
telecommunication lines affect your aerial.
Therefore, be careful to install your aerial
away from these and metal surface in such
a way that it shall not move. Do not make
your aerial cable longer than required and do
not coil it. Make sure that it is not crimped
passing through a window or door. Your
aerial and cable might be affected by natural
phenomena such as rain, wind, smoke and
humidity over time. Periodically check your
aerial and equipment.
The performance of the remote control will
be reduced at a distance of 8 meters from or
at an angle of 30 degrees beyond the centre
of the TV.
4.2-Powering on your device
and the initial use
1. Insert the mains lead or the adaptor into
the appropriate power supply input located
on the back panel of the LCD TV.
2. Insert the plug of the mains lead or
adaptor, supplied with the TV into the mains
socket.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Your new television
5.1-TV Control Panel
or
or
Stand by indicator
Power / Standby button
Bright light: TV is in Stand-by
Dimmed light: TV is On
No light: Power Cable is not connected
5.2-External Connections
1-Power input
2-Aerial input
3-AV1 scart
4- Video input PHONO connector
5- Audio input PHONO connector (L)
6- Audio input PHONO connector (R)
7-VGA (PC connection input) (*)
8- PC audio input (*)
9- CI Slot Input
Note: Above drawing for external connections is representational. Their order and places on
your TV may be different.
(*): These features are optional and they are not available on all models.
5.3-External Connections Table
Panel Size
15”
STD
STD
OPT
OPT
STD
Scart 1
Audio/Video PHONO(Input)
VGA Input
PC Audio Input
CI Slot Input
STD: STANDARD OPT: OPTIONAL
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4-Remote Control
Stand-by mode On/Off button
Temporary sound mute (Mute) button
Source menu button
Picture Format selection button
Subtitle selection button (D)
Sound selection button (D)
Numeric buttons
Favorite channel selection button (D)
Page Stop button in Txt mode (Hold)
EPG selection button (D)
Question/Answer button in Txt mode (Reveal)
Information button
Index page button in Txt mode
MENU button
Return to previous menu button
Up movement button (Menu)
Next page selection button in Txt mode
Down movement button (Menu)
Previous page selection button in Txt mode
Left movement button (Menu)
Right movement button (Menu)
Menu selection confirm
Volume down button
Volume up button
Program forward selection button
Program backward selection button
Red teletext button
Green teletext button
Yellow teletext button
Blue teletext button
TV/Teletext selection button
Teletext page enlarge button (Double)
Picture Mode selection button
Page update button in Txt mode (Update)
Last viewed program selection button
Sub page button in Txt mode (Sub Page)
(D) : Digital Mode Only
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Performing the initial power-on settings
6.1.4-Temporary sound mute (MUTE)
6.1-TV controls
To temporarily mute the sound of
your television, press the MUTE
6.1.1-Temporary on/off (STAND-BY)
When you press the red STANDBY
button on your remote control while
your television is switched on, the
sound and the picture will go off.
In the stand-by mode, the power
indicator of your television will glow
brighter. To switch your television
back on, either press any numeric button or
PR+/PR- buttons.
button on your remote control. In
that case, MUTE symbol will appear
on the screen. When you press the
same button a second time, the sound will
be restored. If you press the VOL+ button
while in the Mute mode, the sound level is
increased and the Mute function is aborted.
6.1.5-Returning to Selected Program
(SWAP)
Allows you to switch between the
current program you watch and the
last selected program. For example,
if you change the channel to Program
11 while you were watching Program 1, press
SWAP button to switch back to Program
1. Press SWAP button to switch back to
Program 11 again.
Caution! If you are not going to use your
television for a long time, unplug its power
cable from the socket.
6.1.2-Program selection
You may switch to the previous or
next program by pressing the P-/P+
buttons located on your television and
your remote control. You may enter
the number of the program you would
like to select using the numerical
buttons. For example, to switch
to the program number 12, press
respectively the numeric buttons 1
and 2 on your remote control. You
can perform the program selection
also from the Program Table. See page 9 for
the program table.
PR 11
PR 01
PR 01
6.1.6-Main Menu
Press the MENU button. The Menu
including all the setting menus will
appear on the screen. Navigate
through the Menu titles with the Up /
Down movement buttons and press
the OK button to select the desired
menu. If you want to exit the menu
in any step, or return to the previous
menu while you are in a sub menu,
just press the BACK or MENU button.
6.1.3-Digital TV, Analogue TV and AV
Mode Selection
Press the AV button on your
remote control. SOURCE menu
will be displayed. Select DIGITAL,
ANALOGUE or desired AV mode
with Up/Down movement buttons
and confirm with OK button so that
your television will switch to the
source you have selected.
MAIN MENU
PICTURE
SOUND
PROGRAM TABLE
SETUP
FEATURES
MENU
SELECT
EXIT
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Select AUTO TUNING tab and confirm
by pressing the OK button. COUNTRY
SELECTION menu will be displayed.
6.2-Turning on the TV and
Setting the Channels
LANGUAGE menu displays when you turn
on your television for the first time. Using
the Right/Left movement buttons, select
the desired language. Then, the COUNTRY
SELECTION menu will be displayed.
Select the country by using Up/Down,
Left/Rightmovement buttons and press
OK button to start the auto programming.
Channel Searchmenu will be displayed and
digital channels are scanned and stored in the
memory. After completion of the searching
process Channel Search Results menu
will be displayed. Number of TV and Radio
channels already detected and stored in the
memory at the end of the search process will
be displayed in this menu. Finish the Digital
channel searching process by pressing the
OK button.
PRESS OK KEY TO START ANALOGUE
SEARCH PRESS MENU KEY TO EXIT
message will be displayed. You can make
Analogue channel tuning with OK button
or finish the searching process by pressing the
MENU button.
6.3-Performing Digital Tunings
You can either tune the Digital programs
automatically or manually and store them in
your television.
COUNTRY SELLECTION
NETHERLANDS
NORGE
ÖSTERREICH
POLSKA
PORTUGAL
SCHWEIZ
SUOMI
SVERIGE
TÜRKİYE
U.K.
..........................
BELGIUM
CZECH REP
DANMARK
DEUTSCHLAND
ELLADA
ESPANA
FRANCE
HUNGARY
IRELANDA
ITALIA
START AUTOPROGRAMMING
MENU
BACK
Select the country by using Up/Down,
Left/Rightmovement buttons and press
OK button to start the auto programming.
Channel Searchmenu will be displayed and
digital channels are scanned and stored in
the memory.
Note: You can also assess AUTO TUNING
menu from the Complete Channel Search
tab in the System Menu under Digital
Features menu.
6.3.2-Manual tuning of channels and
storing in the memory
In digital mode: Press MENU button,
MAIN MENU will be displayed.
Select SETUP tab with Down
movement button and confirm with
the OK button. SETUP menu will be
displayed. Select MANUAL TUNING
tab and confirm by pressing the OK
button. Manual Search Parameters
menu will be displayed.
6.3.1-Automatic Tuning of Channels
and Storing in the Memory
Press AV button on your remote
control, select DIGITAL tab from the
SOURCE menu by using Up/Down
movement buttons and confirm by
pressing the OK button. Your TV will
switch to Digital mode. Press MENU
button, MAIN MENU will be displayed.
Select SETUP tab with Down
movement button and confirm with
the OK button. SETUP menu will be
displayed.
Manual Search Parameters
21
Channel
Frequency
Update of Channel List
474000
Add channels
SETUP
AUTO TUNING
MANUAL TUNING
FIRST TIME INSTALLATION
Change
Start
Back
MENU
BACK
SELECT
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Highlight the Channel tab by means
of Up/Down buttons and directly
Select the PROGRAM TABLE item
from the main menu by means of
Up/Down movement buttons to
access program table and press OK
button to confirm. Program Table will
be displayed. You can also access
the program table menu directly by
pressing the OK button on your remote
control when there is not any open menu on
the screen.
enter the frequency number of the
channel you want to search, if you
know, by using the numeric keys
on the remote control. If you don’t
know the frequency number, you
can scan frequencies by using the Left/
Right movement buttons. After entering
the frequency you want to search, highlight
Update of Channel List tab with Up/Down
movement buttons and select either one
of Add channels, Replace channels or
Erase channel list items, then press OK
button to start searching. Channels will
be searched or changed according to the
search method you have chosen.
ALL
1 Kanal
2 Kanal
3
4
5
Channel Search
Waiting for signal...
Back
Select
Change List
Edit List
Service found:
TV:
0
Radio:
0
Other:
0
6.3.3.1-Displaying Television and
Radio channel lists and selecting
the channels
Stop Search
Add Channels : With this option, the new
channels in the frequency which is desired to
be manually searched will be scanned and
added to the existing channel list.
Replace Channels : With this option, you
can update the existing channel list with the
modifications made by the broadcasting
enterprise.
Erase Channel List : With this option,
you can delete all channels in the existing
channel list to store only the new channels in
the desired frequency into the memory.
When the Program Table menu is
opened, all TV and Radio channels
stored in the list are displayed.
You can navigate between the
channels with Up/Down, Left/Right
movement buttons or you can select
any channel you wish by pressing the
OK button.
Note: You can also assess Manual Search
menu from the Manual Channel Search
tab in the System Menu under Digital
Features menu.
6.3.3-Program Table
With the program table, you can see the
stored channels in a list, switch between
TV channels and Radio channels or create
your favorite channels list for 6 TV and Radio
channels according to your preference.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Up/Down movement buttons and
navigate through the program data
with Right movement button. To get
further information about the program
press INFO button and detailed
information about the selected
6.3.3.2-Creating favorite channels
list
You can create 6 favorite channel
lists according to your personal
preferences. To do this press the
RED button when you are in Program
table. Favorite Lists will be displayed.
All TV channels can be seen on the
Left hand side and favorite channels
on the Right hand side. In All TV
Channels list select the channel you
want to add to the favorites list by
program will be displayed. Press
the GREEN button to display next
day’s program information, press
the RED button to display previous
day’s program information and press
OK button to add Reminder to any
program. You can use FAV button
on your remote control to switch
between TV, Radio and Favorites lists
using Up/Down movement buttons and
press OK button to confirm; name of the
channel you have selected will be displayed
on the favorite channels list. Repeat the
same steps fore every channel you want
to add. To create a different favorites list,
you can change the favorite channels list by
pressing FAV button on your remote control
and add channels to these lists as described
above. To select directly the favorite
channels lists you have created, you can use
the FAV button on your remote control.
in the EPG menu.
Important Note: Not all broadcasters
supply a detailed TV guide. Most of the
broadcasters provide daily program
information, but they do not give detailed
explanations. Some broadcasters, on
the other hand, do not give any program
information at all.
6.3.5-Digital Features
Note: You can also access the Favourite
Lists menu from the scroll down menu of
Digital Features menu.
To enter digital features menu, select
FEATURES tab from the main menu
by using Up/Down movement buttons.
Select DIGITAL FEATURES tab from
FEATURES menu by using Up/Down
movement buttons and press OK button to
confirm. DIGITAL FEATURES menu will be
displayed.
6.3.4-Electronic TV Guide (EPG)
If it is supported by the broadcaster, the
electronic TV guide gives entire general
information about the programs of the next 8
days (for digital channels only).
To display the Electronic TV Guide,
press EPG button on the remote
control. Electronic TV Guide will be
displayed.
Digital Features
Language Settings
Access Control
User Interface Options
Timers
You can select the channel by using the
Favourite List
No Common Interface Module Present
System Menu
Program
13:15
15:10
Reality Show
13:45
Monday 18/8/2007
All TV
1 BBC ONE
2 BBC TWO
3 ITV1
4 CHANNEL 4
5 FIVE
13:15
15:10
17:20
20:45
21:50
22:50
Program
News
Film
TV Series
Film
Program
Back
Select
6 ITV2
You can select the menu headings with Up/
Down movement buttons to make settings.
Details
Exit
Reminder
Next Day
Previous Day
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Note 2: The password has been set as 0000
at the factory. You can change the password
as you wish under Change PIN item in the
Access Control menu.
6.3.5.1-Language Settings
You can select subtitle and sound language
provided that the broadcast is supported for
all digital broadcasting channels. Unless you
make a selection, the language supported by
the broadcaster will be selected automatically.
6.3.5.3-User Interface Options
With this feature, you can decide whether
to display in the list the channels that could
not be unscrambled by the CI card installed
on your television. To do this, you can select
ON, OFF or AUTO options.
To perform language selection, select
Subtitling Language 1, Subtitling
Language 2, Audio Language 1,
Audio Language 2 tab from the
Language Settings menu by using
Up/Down movement buttons and
make your language selection with
Left/Right movement buttons. You
can also select subtitles directly by
SUBT button on your remote control
or make sound selection by AUDIO
button.
6.3.5.4-Timers
In this menu you can view Reminders you
had entered from the EPG or change the
entered Reminders.
6.3.5.5-Favourite Lists
Please see 6.3.3.2-Creating favorite channel
list for detailed explanation of this feature.
6.3.5.2-Access Control
6.3.5.6-Common Interface Module
With this feature, you can lock the channels
that are not suitable for children.
In this menu, you can check the CI Module
settings that you can attach to your
television.
Access Control
Lock/Unlock Channels
Change PIN
6.3.5.7-System Menu
You can display your television’s hardware
and software data under this menu.
6.4-Performing Analogue
Tunings
You can either tune the programs
automatically or manually and store them in
your television.
Select
Back
Lock/Unlock Channels: Select Lock/
Unlock Channels tabs from Access Control
menu and press OK button to confirm. All
TV Channels list will be displayed; select the
channel you want to lock with Up/Down
movement buttons and press OK button
to confirm. x mark will be displayed at the
beginning of the channel which is locked.
To unlock, repeat the same steps. Select
the channel to access the locked channel
and enter the correct password into the
displayed password screen. The channel
will not be displayed unless the correct
password is entered.
6.4.1-Automatic tuning of channels
and storing in the memory
Note: If your television does not receive any
aerial broadcast for a period of 5 minutes,
it automatically switches to the stand-by
position. The countdown symbol is displayed
on the screen during the last 1 minute.
You can tune the programs
automatically with the Autoprogram
function of your television and then
sort the channels as you desire
by means of the Program Table.
Press the MENU button on your
Note 1: To re-prevent access after entering
the correct password and displaying the
locked channel, your television has to be
switched to Standby mode and turned on
again.
remote control. Select SETUP tab
by pressing the down movement button
and confirm your selection with OK button.
Setup menu is displayed. Select PROGRAM
NO tab by pressing the Up/Down
14
Download from Www.Somanuals.com. All Manuals Search And Download.
movement buttons in Setup menu, enter the
channel number to be searched and stored
automatically, then select AUTOPROGRAM
tab by using the Up/Down movement
buttons and press OK button; Country
Selection menu will be displayed. In the
Country Selection menu, select the country,
whose broadcast you would like to watch
in priority, by pressing the Up/Down or
Right/Left movement buttons and start
autoprogramming by pressing the OK
button.
To stop the process at any given time,
please press the MENU button. The
Program Table, which will allow you to sort
the channels as you wish, will be displayed
after the auto-search is complete.
6.4.2- Manually searching and
storing the channels
6.4.2.1-If you already know the
channel number:
Press the MENU button. Move to
the SETUP menu by pressing the
Down movement button in the Main
Menu and confirm your selection with
the OK button. The Setup menu is
displayed.
SETUP
SYSTEM
I
CHANNEL
FINE TUNE
SEARCH
S06
0
PROGRAM NO
STORE
P13
SETUP
AUTOPROGRAM
SYSTEM
I
CHANNEL
FINE TUNE
SEARCH
S06
0
MENU
BACK
SELECT
PROGRAM NO
STORE
P13
AUTOPROGRAM
COUNTRY SELLECTION
BELGIUM
CZECH REP
DANMARK
DEUTSCHLAND
ELLADA
ESPANA
FRANCE
HUNGARY
IRELANDA
ITALIA
NETHERLANDS
NORGE
ÖSTERREICH
POLSKA
PORTUGAL
SCHWEIZ
SUOMI
SVERIGE
TÜRKİYE
U.K.
..........................
MENU
BACK
CNANGE
Select the system in which you
would like to make the search from
the SYSTEM tab by pressing the
Right/Left movement buttons. Move
into CHANNEL tab by pressing the
Down movement button. Press OK
on your remote control and select
“S” for cable channels and “C” for
channels received via the aerial. Move
onto the PROGRAM NO tab and
START AUTOPROGRAMMING
MENU
BACK
The channels will be automatically searched
and those found will be stored in memory
starting from the program selected in the
setup menu. At the same moment, the
Autoprogram menu will be displayed and
a marker indicating the progress of the
autoprogramming will appear as shown
below.
enter the channel number in which
you would like to have the channel stored.
If the broadcast viewed on the screen is
of your desired quality, first move onto the
STORE tab with the down movement
button to store in the memory the selection
you have made and store the channel by
pressing the right or left movement buttons.
The prompt STORED will be displayed
briefly. The channel will be stored according
to the program number of your choice.
You can tune and store in memory other
channels the same way. In the event that
you wish to exit the channel settings menu
for any reason, simply press the MENU
button.
SEARCHING
% 20
STOP
MENU
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4.2.2-If you do not know the
channel number
6.4.4-Program table
Press the MENU button. Move to the
PROGRAM TABLE tab by pressing the
Down movement button in Main Menu and
confirm your selection with the OK button.
Program table menu will be displayed.
Press the MENU button. Move to
the SETUP menu by pressing the
down movement button in the Main
Menu and confirm your selection with
the OK button. The Setup menu is
displayed. Select the system in which
you would like to make the search
from the SYSTEM tab and move
to the CHANNEL tab by pressing
the down movement button. Press
OK on your remote control and
PROGRAM TABLE
00
05
10
11
12
13
14
01 Channel 06
02 Channel 07
03
04
08
09
NAME
SKIP
DELETE
MOVE
select “S” for cable channels and
“C” for channels received via the
MENU
BACK
SELECT
aerial. Select SEARCH tab using
the Up/Down movement buttons,
and scan the channels in ascending
order with Right movement button
and in descending order with Left
movement button. If the channel that
is found is of your liking, select the STORE
tab. Then store it in the memory pressing
the right or left movement buttons. Repeat
the same procedure for other channels by
selecting the program number of your choice
from the PROGRAM NO tab. If the channel
you found is not of the desired quality and
requires Fine Tuning or if you would like to
rename the channel, refer to the relevant
sections.
6.4.4.1-Switching the locations of
the stored channels
Select the program you would like
to relocate by pressing the Up/
Down or Left/Right movement
buttons. “Press the “GREEN”
button. The color of the channel
name will change. Move to the other
program you would like to relocate
by pressing the Up/Down or Right/
Left movement buttons. Finish the
relocation process by pressing the
“RED” colored confirmation button.
The channel in the first program
number you selected has been
6.4.3-Fine Tuning
moved to your second selected program
number and the channels between both
program numbers have been shifted to the
initially selected program number. After
setting is complete, press the MENU button
to exit the menu.
If the channel you found is not of the
desired quality, then select the FINE
TUNE tab by pressing the Down
movement button in the Setup menu.
Using the Left/Right movement
buttons on your remote control,
6.4.4.2-Deleting a stored channel
Select the program you would like
to delete by pressing the Up/Down
or Right/Left movement buttons
while you are in the program table.
“Press the “BLUE” button. You can
perform the deletion process by
pressing the “RED” confirmation button or
abort the process by pressing the “GREEN”
button. “Once you press the “RED” button,
the selected program is deleted and the
following channels are transferred to
previous program number. After setting is
complete, press the MENU button to exit
the menu.
adjust the broadcast displayed on the
screen to your desired quality. Under
normal circumstances, you will not require
to use the Fine Tune function. The AFC
values of your television will automatically
adjust and lock themselves to the channel.
However, you might need it in case the
television transmitters do not operate
according to the standards. To store in the
memory the settings you have made, select
the Store tab and press the Right or Left
movement button.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4.4.3-Skipping a stored channel:
6.4.4.4-To name the channels
In the event that you do not wish to
see certain programs while navigating
through the channels using the Up/
You can assign your program or
programs of choice the names that
have a maximum of five characters.
Down buttons, then you can use
Select the program you would like
to name from the Program Table
this function. Select the program that will be
hidden by pressing the Up/Down or Right/
Left movement buttons while you are in the
program table. “Press the “RED” button.
The name of the program to be skipped
shall appear in red. You may perform this
procedure for more than one program. To
view the skipped program, directly enter the
program number using the numeric buttons.
To cancel the program skipping process,
press again the “RED” button. After setting
is complete, press the MENU button to exit
the menu.
by pressing the Up/Down or Right/Left
movement buttons. “Press the “YELLOW”
button. An empty space appears beside
the channel for which you would like to
specify name information. Here, choose
the desired letter, number or sign using
the Up/Down movement buttons. For the
second character, press the Right/Left
movement button and then select the
desired letter, number or sign again with the
Up/Down movement buttons. After entering
all the characters, store the name you have
written in the memory by pressing the “RED
confirmation button. To write names for any
of the other programs, simply repeat the
above procedure. If you want to exit the
menu, simply press the MENU button. If
the program is not named, then the channel
number of that program will be displayed
automatically.
7 The settings on your new television:
You can select the desired title to be
7.1- Sound Menu Settings
7.1.1-Sound Menu
processed from this menu. You can select
the desired setting by pressing the Up/
Down movement buttons and adjust their
levels with Right/Left movement buttons.
You can adjust BASS, TREBLE, BALANCE
levels as you desire. The changes you have
made in the picture settings will be stored
in the memory without requiring any other
operations.
You can perform sound settings by
entering the Sound menu. For this, press
the MENU button on your remote control.
Select SOUND by pressing the Up/Down
movement buttons from the main menu and
press the OK button. The Sound menu is
displayed.
7.2-Picture Menu Settings
7.2.1-Picture Menu
SOUND
BASS
TREBLE
BALANCE
You can perform other picture settings by
entering the Picture menu. For this, press
the MENU button on your remote control.
Select PICTURE by pressing the Up/Down
movement buttons from the main menu and
press the OK button. The Picture menu will
be displayed.
MENU
BACK
CNANGE
17
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTE: Your TV is equipped
with Digital Comb Filter feature to increase
the picture quality. This option can not be
changed by the end user if it is set to ON.
PICTURE
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
COLOUR TEMP.
DNR
NORMAL
OFF
7.2.5-Picture Format
With this option, you can view the broadcast
you watch in a format of your choice. You
can display the broadcasts in 4:3, AUTO or
16:9 formats. You can change the picture
format by pressing the 16:9 button in order
to view certain 16:9 format broadcasts and
DVD movies.
MENU
CHANGE
BACK
You can select the desired title to be
processed from this menu. You can
select the desired setting by pressing the
Up/Down movement buttons and adjust
their levels with Right/Left movement
buttons. You can adjust BRIGHTNESS,
CONTRAST, COLOR and SHARPNESS
levels as you desire. The changes you have
made in the picture settings will be stored
in the memory without requiring any other
operations.
16:9 Picture format
4:3 Picture format
7.2.2-Color Temperature
7.3-Features Menu Settings
Color intensity of the picture can be
adjusted with this feature. Select COLOR
TEMPERATURE tab from the Picture menu
by pressing the Up/Down buttons and
then select one of the COOL, NORMAL or
WARM options by pressing the Right/Left
buttons.
Press the MENU button on your remote
control.Select FEATURES by pressing the
Up/Down movement buttons from the
main menu and press the OK button. The
Features menu will be displayed. You can
select the titles for which you would like to
perform an operation in this menu by using
the Up/Down movement buttons.
7.2.3-DNR (Noise reduction)
You may reduce interference and noise
formed in the picture by using this feature.
Select DNR tab from the Picture menu
by pressing the Up/Down buttons and
then select one of the OFF, LOW or HIGH
options by pressing the Right/Left buttons.
FEATURES
LANGUAGE
ENGLISH
OFF
SLEEP TIMER
DIGITAL FEATURES
ACTIVE Aerial
OFF
7.2.4-Picture Smart
MENU
You can select either one of the
three non-adjustable settings in the
memory or the options you have
CHANGE
BACK
adjusted by pressing the ( ) button
on your remote control. SOFT, NATURAL
and RICH are default values; USER
represents the values you stored in memory.
7.3.1-Off Time
Off time switches your television
automatically to Standby Mode after the
preset time has elapsed. You can adjust
this time between 15 and 120 minutes with
increments of 15 minutes. To activate this
feature, select the Off Time tab and press
Right/Left movement buttons to select the
desired time.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
television by the tuner of your television
without needing any external source.
Note: Digital Features tab under the
Features menu is only available in Digital
mode. This tab does not display on the
menu in Analog mode.
7.3.2-Digital Features
You can adjust the Digital TV features from
this menu. See page 12-13.
7.3.3-Active Aerial
When this feature is set to On, you can feed
an external aerial you will connect to your
8 Teletext
Being one of the most prominent services
of broadcasting today, Teletext renders
the TV more fruitful. Teletext means in
short the transmission of various updated
information along with the TV broadcast
signal in the form of text and graphics. To be
able to receive a quality teletext broadcast,
a good aerial system and a broadcast
signal that is not weak, with no reflections
and interference from other channels are
required. Even in a very clear reception, it
is normal for some characters or tabs to
be lost. Such conditions will automatically
be improved in a short time under normal
circumstances.
8.3-Page enlarge button (DOUBLE)
Using this button, you can watch
the top half of the teletext page in an
enlarged format. To be able to view
the bottom half of the enlarged page,
press the same button for the second time.
Once you press the same button the third
time, the page will be restored to its normal
size.
8.4-Page Stop (HOLD)
Some information is laid out by the
broadcaster in multiple pages and it
is broadcast in an automatic cycle
8.1-Entering the Teletext Mode
mode. For example, on a text of four pages,
the pages are indicated with the figures 01,
02, 03 and 04 on the bottom of the page. To
view one of these pages for a longer time,
press the FAV button. When you press the
same button again, the cycle continues.
In a channel that does not have the
Teletext feature, NO TELETEXT will
be displayed when you press the TXT
button. In order to switch your television
to the teletext broadcast, please press the
TXT button in a program that has a teletext
broadcast. To switch back to the television
broadcast, press the same button twice.
Once you have switched to the teletext
broadcast, the initial page that appears will
be the index page. P100 In this page, the
titles of the topics in the teletext broadcast
and the initial page numbers will appear.
8.2-Page Selection
8.5-Subpage selection (SUB)
If the page of text you are viewing contains
sub pages the page numbers starting
from 01 appear on the screen. You
can switch to the sub pages with the
SWAP button. In which case, the sub
page tab is displayed on the bottom
line within “red -” and “green +”
frames. You can select the sub pages
by pressing the “RED” and “GREEN”
buttons. You can exit the subpage by
pressing the SWAP button again.
To be able to view the page you
would like on the screen, type in
the number of that page using the
numerical keys. You can see the
number you have entered on the left
side of the upper title tab. When you
would like to turn the pages one by
one, you can go to the next page
pressing the up button and to the
previous page pressing the down
button. Press the INFO button to
return to the Index page.
8.6-Temporary TV Picture (UPDATE)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
This button allows you to switch to the
television picture while the page you want
is being searched in the teletext
8.10-Toptext (optional)
There is a topics line in yellow and blue at
the bottom of the teletext screen. You can
select the relevant topic by pressing the
yellow or blue buttons on the remote control.
You can select the next page by pressing
the red button and the previous page by
pressing the green button.
broadcast eliminating the need to wait
during the search. You may switch
to the television picture by pressing the (
button while Teletext is searching for your
desired page. Once the page you want is
found, the number of that page appears on
the screen.
)
Note: Fastext and Toptext features are not
available from every program.
8.7-Question - Answer Button
(REVEAL)
Sometimes, a teletext page contains a
hidden answer such as a game or
a riddle. Press the EPG button to
disclose the hidden answer.
8.8-Clock
The Clock function of the SIZE button; press
the SIZE button when you want to
learn the time while watching any
television channel. In that case, a
clock will appear on the lower right
corner of the screen. You can remove the
time information from the screen by pressing
the same button.
8.9-Fastext
The colored buttons on the remote control
are for the fastext feature. When you select
any page, the titles on various subjects may
appear on the screen in four different colors
or inside colored frames (red, green, yellow
and blue). By pressing the button pertaining
to the relevant color on the remote control,
you can access the subject of your choice
without waiting.
Note: The fastext feature is not available for
all teletext broadcasts. It is determined by
the broadcaster whether it is to be broadcast
or not.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
9 External equipment connection:
SCART SOCKET
You can connect various compatible audio
and video devices to your television.
AV inputs: Press the AV button on your
remote control. Source menu will be
displayed. Here, you can select whichever
input you would like.
VCR/VCD
DVD/PVR
DIGITAL: While in the AV or Analog TV
modes, move onto this option and press OK
button for switching to the Digital TV mode.
DECODER
ANALOGUE: While in the AV or Digital TV
modes, move onto this option and press OK
CAMCORDER
VIDEO GAME
button for switching to the Analog TV mode.
SCART : To watch the picture of the
broadcast device connected to Scart1,
move onto this option and press the OK
button. (You can watch via this Scart if the
connected device has a RGB output).
AV : To watch the picture of the broadcast
device connected using the PHONO input,
move onto this option and press the OK
button.
AUDIO
VIDEO
9.2-PC Mode
PC (Optional): To be able to watch the
images in PC mode, move onto this option
and press the OK button.
(Optional)
Your LCD television can also be used as a
PC monitor via the VGA input.
9.2.1-PC Connection:
Connect the D-Sub15 connector to the
PC-IN input on the rear of your television
using a suitable cable (not supplied with the
television). Again using a suitable cable, you
can also listen to the sound from your PC by
connecting the sound output of your PC to
the PC AUDIO-IN input on the rear of your
television.
9.1-Connection types for
external devices
Your TV is equipped with 4 inputs including
aerial input, which allows for the external
device connection. These inputs are:
9.2.2-Switching to the PC Mode
For your LCD-TV to switch to the monitor
(PC) mode, press the AV button on your
remote control. The AV menu appears on
the screen. Select PC by pressing the P+/
P- movement buttons and press the OK
button. You can also use the PC button on
your remote control to directly switch into
PC mode.
1-Aerial input
2-VGA input (optional)
3-SCART input 1
4-PHONO input
You can connect your external device
supporting the suitable inputs to your TV
via these inputs. By pressing the AV button
on your remote control, select the external
source input to which you connected your
device.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
9.2.3-PC Setting
9.2.7-PHASE
Enter into the SETUP menu from the Main
Menu by pressing the MENU button in the
PC mode. In order to make the necessary
settings in this menu, you can use the P+/P-
/ -VOL/VOL+ movement buttons on your
remote control. You can make the following
settings for your monitor in this menu.
Using the -VOL/VOL+ movement buttons,
you can ensure that the colors and shapes
are exactly consolidated on the PC image.
9.2.8-AUTOCONFIGURATION
The most suitable geometric settings
in accordance with the entry mode are
configured by this function. For this operation,
select the AUTOCONFIGURATION tab and
press OK button. You can adjust the volume
level of the source you have connected to the
Audio-In input at the back of your TV by using
the -VOL/VOL+ buttons.
9.2.4-HORIZONTAL POSITION:
Horizontal position setting
9.2.5-VERTICAL POSITION: Vertical
position setting
9.2.6-CLOCK
Note: In the Monitor mode, you can make the
Brightness, Contrast, Sharpness, Red, Green
and Blue Settings from the PICTURE menu.
This is the pixel clock frequency. User can
narrow down or enlarge the display by
selecting a desired value.
9.3-Connecting a video recorder device and a digital satellite
receiver
ANT IN
ANT OUT
ANT IN
ANT IN
ANT OUT
Scart 1 TV IN/OUT
Scart 2 AUX IN
SCART Socket
VIDEO RECORDER
REAR OF THE TELEVISION
DIGITAL SATALLITE RECEIVER
10 Help and tips
•
•
The picture quality can be affected when
two external devices are connected. Try
disconnecting one of the devices.
Try adjusting the fine tuning.
The television does not function
Make sure that the power cable of the
television is connected to the mains and the
power on-off switch is turned on.
No picture
Poor picture quality
•
•
•
Is the aerial connected correctly?
Is there any damage to the aerial cable?
Are the plugs on the aerial cable
connected correctly?
•
•
Is the aerial cable connected?
If you are using a satellite aerial, has the
aerial been adjusted to receive broadcast
in the best way?
•
Are you sure that you have pressed the
correct button on the remote control?
•
•
Make sure that the aerial is far from
devices that emit electromagnetic waves.
(Neon lights, loudspeakers etc.)
Try changing the direction of the external
aerial. High buildings and mountains
can cause a faded picture or ghosting
(double picture).
No sound
22
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Temporary sound mute may be on. Try
pressing the mute button.
Is the sound turned down?
The remote control does not
function
•
•
Try replacing the batteries.
Make sure that there are no obstructions
between the remote control and
television.
Symptoms
No picture and sound
√
√
√
√
√
√
√
√
√
No sound, picture available
No picture, sound available
√
√
√
√
√
√
√
If your television does not work properly
even though you tried the above mentioned
solutions, try turning it on and off again. If
you cannot start your television even though
you have applied all noted methods, refer to
the dealer or authorised service from where
you purchased the product. Never attempt
to repair a faulty device yourself.
Low quality picture
√
√
√
Foggy picture
√
√
√
√
√
√
√
√
√
√
√
√
Double picture
Line on the picture
√
√
√
Distorted picture
√
√
√
√
√
√
√
√
√
√
√
√
Distorted broadcast on some channels
Horizontal lines exist
√
√
Vertical fluttering in the picture
√
√
√
Weak color
No color
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
The remote control does not function
TV does not respond to the commands
Fluttering in the teletext
√
√
√
√
11 Technical specifications chart
Note: Your television has been manufactured
SCREEN SIZE
15”
in accordance with the system available in your
country and this system cannot be changed by
the user.
15”, 4:3
Active matrix
TFT
Panel type
Sound output
2x2 W
22 W
<2 W
8
Power consumption
Stand by power value
Teletext page
General technical specifications
Power supply AC:
Power supply DC:
Program memory Analog:
Program memory Digital:
RF Aerial input:
230V 50 Hz
12V (*)
100
1000
75 Ohm (Co-axial)
8 Ohm
Mono / AV Stereo
2xUM - 4, IEC R03 or AAA 1.5V
VHF (Band I Channel 2-4)
VHF (Band III Channel 5-12)
UHF (Channel 21-69)
Cable TV (S1-S20/S21-S41)
PAL BG
Loudspeaker impedance:
Sound systems:
Batteries:
Channels received:
Broadcasting systems received:
PAL SECAM BG
PAL SECAM BG DK
PAL SECAM BG LL’
PAL I
(*): These features are optional and they are not available on all models.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
12 MAIN UK TRANSMITTER STATIONS
UHF CHANNELS
BBCI BBC2 ITV CH4 CH5
STATIONS CT D
BBCI BBC2 ITV CH4 CH5 Map
Regional Main stations
North West
Caldbeck
Map
30
55
68
34
62
66
28
59
48
32
65
56
56
48
56
12
15
45
Bluebell Hill
Crystal Palace
Dover
Oxford
East
Sandy Heath
Sudbury
Tacolneston
Scotland
Angus
40
26
50
49
46
33
56
52
43
23
66
64
65
30
53
67
29
28
30
31
Winter Hill
37
Douglas (IOM)
North
Belmont
Emley Moor
North East
Bilsdale West Moor
Chalton
Pontop Pike
Midlands (West)
Ridge Hill
Sutton Coldfield
The Wreckin
Mindlands (East)
Waltham
South West
Beacon Hill
Caradon Hill
Huntshaw Cross
Redruth
Stockland Hill
Channel Islands
Fremont Point
West
Mendip
South
Hannington
Midhurst
Rowbridge
22
44
28
51
25
47
32
41
56
37
17
16
31
51
62
27
44
55
24
41
59
21
47
65
39
35
52
25
26
24
33
39
58
26
45
64
29
49
61
23
42
54
35
14
11
13
56/58
57
40
31
33
22
33
40
33
39
31
55
63
46
27
26
28
26
46
26
45
27
62
60
43
24
23
25
23
43
23
49
24
59
53
50
21
29
32
29
50
29
42
21
65
37
37
48
35
67
6
8
7
9
5
49
1
4
3
2
10
Black Hill
Cragkelly
Darvel
22
46
26
28
40
33
25
43
23
32
50
29
35
37
25
23
22
20
Durris
Eitshal (Lewis)
Keeylang Hill
Knock More
Rosemarkie
Rumster Forest
Selkirk
Wales
Blaenplwyf
Carmel
58
64
61
54
35
21
57
22
55
51
33
63
28
62
44
26
60
25
59
41
23
53
32
65
47
29
37
38
40
39
36
67
37
52
56
31
57
57
52
46
44
27
63
63
45
40
51
24
60
60
49
43
41
21
53
53
42
50
47
44
42
19
18
43
41
51
58
44
64
41
61
47
54
Uanddona
Moel-y-Parc
Presely
37
35
35
37
Wenvoe
39
61
31
45
55
24
42
58
27
66
68
21
34
32
33
N.IRELAND
Brougher Mountain
Divis
22
31
55
28
27
62
25
24
59
32
21
65
37
31
47
46
48
Limavady
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Plc
13 Guarantee - Television
Your new television is guaranteed against the cost of breakdown repairs for twelve months
from the date of the original purchase.
What is covered?
• All repairs necessary as a result of faulty materials,defective components or
manufacturing detect.
• The cost of all functional replacement parts,excluding remote control batteries
• The labour costs of a Beko approved repairer to carry out the repair
• You may be offered a replacement instead of repair under guarantee.
You dealer will advise you.
What is not covered?
• Transit or delivery damage
• Accidental damage
• Misuse, or abuse.
• Cabinet or appearance parts,including knobs and flaps
• Remote control batteries.
• Repairs or replacements required a a result of unauthorised repairs or inexpert
installation that fails to meet the requirements contained in the user instruction book.
• Repairs or replacements to product installed or used on commercial or non-household
premises.
Important notes.
• The product is guaranteed for domestic household use only.
• The guarantee will be void if the product is installed or used in commercial or non-
household premises.
• The product must be correctly installed and operated in accordance with the
instructions contained within the Operating Instructions Booklet provided with the
product.
• The guarantee is given only within the boundaries of the United Kingdom and the
Republic of Ireland.
• The guarantee is not transferable if the product is resold.
• Beko Plc disclaims any liability for incidental or consequential damages.
• The guarantee does not in anyway diminish your statutory or legal rights.
Beko House,Caxton Way,Watford,Herts,WD18 8UF,Tel: 0845 600 4911
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Plc
13 HOW TO OBTAIN SERVICE
Congratulations on your choice of a Beko colour television.Your new television has been
designed and manufactured to the highest quality standards to give you many years of use.To
get the best out of it,please take a few moments to read the instruction book.
Your television is supplied with a full 12 months guarantee,covering parts and labour.Should
you require service under guarantee,simply call the number below (**see note for small screen
sets)
0845 600 4911
Our service receptionist will ask you for your product model number,your retailer’s name,and
the date of purchase when you call.It will assist you if you complete the box at the bottom of
this page when you take delivery of your television so that the information is readily available
should you need it. If it is necessary for an engineer to visit your home he will normally
be there within 48hrs of receipt of your call (excluding Bank Holidays) or at your earliest
convenience.
Before telephoning for service please check the trouble shooting guide in the instruction
book as often minor problems are easily identified and resolved by following the instructions
contained there in.Service visits where there is no fault with the product could incur a charge
even through the product is under guarantee.
Service is also available on the above number after the guarantee period has expired.The cost
of any repairs outside of the guarantee period is payable to the engineer at the time of visit.
Please complete the box below for ease of reference later.
Model Number
Serial Number
Date of Purchase
Place of Purchase
Please keep your purchase receipt.The engineer will need to see it should you require service under
the 12-month Guarantee.
***Special Note:
In home repair servicie is not available on models with a screen size of 21” or under.You
should contact your retailer for advice and assistance on these models..
26
Download from Www.Somanuals.com. All Manuals Search And Download.
FAU.801
Download from Www.Somanuals.com. All Manuals Search And Download.
|