8210Plus/8210/07048/8110S
Particulate Respirator
3M recommended for sanding, grinding, sawing, sweeping and
insulating
User Instructions
(Keep these instructions for reference)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Dispose of used product in accordance with applicable regulations.
Use Limitations
1. This respirator does not supply oxygen. Do not use in atmospheres containing less than
19.5% oxygen.
2. Do not use when concentrations of contaminants are immediately dangerous to life and health, are
unknown or when concentrations exceed 10 times the permissible exposure limit (PEL) or according
to specific OSHA standards or applicable government regulations, whichever is lower.
3. Do not alter, abuse or misuse this respirator.
4. Do not use with beards or other facial hair or other conditions that prevent a good seal between the
face and the sealing surface of the respirator.
5. Respirators can help protect your lungs against certain airborne contaminants, however, they will not
prevent entry through other routes such as the skin, which would require additional personal
protective equipment (PPE).
6. This respirator is designed for occupational/professional use by adults who are properly trained in
their use and limitations. Respirators are not designed to be used by children.
7. Individuals with a compromised respiratory system, such as asthma or emphysema, should consult a
physician and complete a medical evaluation prior to use.
Time Use Limitation
If respirator becomes damaged, soiled, or breathing becomes difficult, leave the contaminated area
immediately and replace the respirator.
Fitting Instructions
Must be followed each time respirator is worn.
Fig. 1
Fig. 2
Fig. 3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 4
Fig. 5
1. Prestretch top and bottom straps before placing respirator on the face (8210 only).
2. Cup the respirator in your hand, with the nosepiece at your fingertips, allowing the headbands to hang
freely below your hand.
3. Position the respirator under your chin with the nosepiece up. Pull the top strap over your head
resting it high at the top back of your head. Pull the bottom strap over your head and position it
around the neck below the ears.
4. Place your fingertips from both hands at the top of the metal nosepiece. Using two hands, mold the
nose area to the shape of your nose by pushing inward while moving your fingertips down both sides
of the nosepiece.
! Pinching the nosepiece using one hand may result in improper fit and less effective respirator
performance. Use two hands.
5. Perform a User Seal Check prior to each wearing. To check the respirator-to-face seal, place both
hands completely over the respirator and exhale. Be careful not to disturb the position of the
respirator. If air leaks around nose, readjust the nosepiece as described in step 4. If air leaks at the
respirator edges, work the straps back along the sides of your head. If you CANNOT achieve a proper
seal, DO NOT enter the contaminated area. See your supervisor.
Removal Instructions
See step 3 of Fitting Instructions and cup respirator in hand to maintain position on face. Pull bottom
strap over head. Still holding respirator in position, pull top strap over head and remove respirator.
NIOSH Approved: N95
At least 95% filtration efficiency against solid and liquid aerosols that do not contain oil.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
This respirator contains no components made from natural rubber latex.
FOR MORE INFORMATION
In United States, contact:
Internet
Technical Assistance
1-800-243-4630
For other 3M products:
1-800-3M-HELPS or
1-651-737-6501
Exported by/Exporté par/Exportado por:
3M Occupational Health and
Environmental Safety Division
3M Center, Building 235-2W-70
P.O. Box 33010
St. Paul, MN 55133-3010
Made in U.S.A.
©3M 2003
38-9017-9661-5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|