Model AMP-602
120 Watt 2-Channel
Power Amplifier
Owner's
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
HIGH PERFORMANCE STEREO AMPLIFIER
This power amplifier has been designed to provide high quality performance with
a minimum of maintenance. However, it's performance will only be as good as the
care and quality of components with which it is installed. We therefore advise that
youreadtheseinstructionsverycarefullytofamiliarizeyourselfwiththeproductand
it's features.
HELP!
1-800-645-4994
Monday - Friday
Saturday
8:30am - 7:00pm Eastern
9:00am - 5:00pm Eastern
Should you require assistance with the installation or wiring of this unit, please call
our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown.
SPECIFICATIONS
Maximum Output Power:
Output Impedance:
Frequency Response:
Channel Separation:
Signal / Noise Ratio:
Input Impedance:
60 watts x 2
Input Sensitivity:
Low-level 200 mv. - 2 v.
High-level 2 - 10 v.
12 volts, negative ground
5 amps.
2 - 8 ohms
Supply Voltage:
Fuse Rating:
20 - 25,000 Hz. ± 1 dB
60 dB
Dimensions (W x H x D): 4-11/16" x 2-1/8" x 9-1/10"
119 mm x 54 mm x 231 mm
90 dB (A-Weighted)
Low-level 10K ohms
High-level 100 ohms
* Due to continuing improvement, Audiovox reserves the right to change features and design without notice.
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
1. Although this unitisdesignedwithbuilt-inself-protectioncircuits, theremaybeapossibilityofdamageifitisnotwired
correctly. Please follow the wiring instructions carefully for the type of system being used.
2. The last lead to be connected is the wire to the positive (+) terminal of the battery. Connect this wire only after having
completed and checked all other connections to the amplifier.
3. By nature of its design, a power amplifier generates heat and requires good air circulation around it to dissipate that
heat. Do not install the amplifier in an enclosed area which does not permit adequate air circulation. Should the
temperature of the unit rise too high, the internal thermal sensors will shut off operation until it has cooled down
sufficiently.
4. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The
use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully
check all electrical connections to the unit.
5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery
and chassis ground must be of a thick enough gauge to provide this voltage to the amplifier. We recommend
#16 gauge wire or larger (smaller gauge #) for the battery and ground leads.
6. Make certain that the speakers to be used with this amplifier are capable of handling the output power (wattage)
of the unit. Use of speakers not rated for the output of this amplifier may cause damage to or failure of the
speakers for which Audiovox will not be liable.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONDIAGRAM
INSTALLATION INSTRUCTIONS
SCREW
1. Select a mounting area where the amplifier will
have sufficient air circulation for proper cooling.
Inadequateaircirculationwillcausethetemperature
of the amplifier to rise and will trigger the
thermal protection mode.
2. Place the amplifier on the mounting surface
and mark the locations of the four mounting
holes as shown in the illustration.
3. Remove the amplifier and drill a 1/8" hole at
each of the four locations.
CAUTION: Before drilling the holes, look at the
underside of the mounting surface. Always
check carefully to avoid drilling into wiring,
braces, fuel or brake lines. CHECK BEFORE
YOU DRILL !
1/8" DIA. HOLE
MOUNTING SURFACE
4. Secure the amplifier to the mounting surface
using the self-tapping screws provided.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING INSTRUCTIONS
The power connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw for the
connection to be made and fully insert the wire (strip 1/2" of insulation from the end) under the respective screw on the
side panel. Tighten the screw down to secure the wire.
1. Power Connection
The battery terminal (+12V) must be connected directly to the positive terminal of the vehicle battery to provide an
adequatevoltagesourceandminimizenoise. Connectingthebatteryterminalleadtoanyotherpoint(suchasthefuseblock)
will reduce the power output and may cause noise and distortion. Use only #16 gauge or thicker (smaller gauge #) wire
for this lead and connect it to the terminal of the battery after all other wiring is completed.
2. Ground Connection
The ground terminal (GND) connection is also critical to the correct operation of the amplifier. Use a wire of the same
gauge as the power connection (#16 or thicker) and connect it between the ground terminal (GND) of the amplifier and
a metal part of the vehicle close to the mounting location. This wire should be as short as possible and any paint or
rust at the grounding point should be scraped away to provide a clean metal surface to which the end of the ground
wire can be screwed or bolted.
3. Remote Turn-On Connection
The amplifier is turned on by applying +12 volts to the remote turn-on terminal (REM). The wire lead to this terminal
should be connected to the "Auto-Antenna" lead from the car stereo which will provide the +12 volts only when the car
stereo is turned on. If the car stereo does not provide an Auto-Antenna lead, the remote turn-on lead may be wired
to an "Accessory" or "Radio" terminal in the car's fuse block. This will turn the amplifier on and off with the ignition key,
regardless of whether the car stereo is on or off. The remote turn-on lead does not carry large currents, so #20 gauge
wire may be used for this application.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING INSTRUCTIONS
4. Speaker Connections
Wire the speakers to the "Speaker Output" terminals as per the Output Wiring Diagram. For most applications, #18
gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. When wiring the speakers,
pay careful attention to the polarity of the terminals on the speakers and make certain they correspond to the polarity
of the corresponding terminals on the amplifier. DO NOT ground any speaker leads to the chassis of the vehicle.
5. Input Connections
This amplifier features both high and low-level input capability. Use either the low-level or high-level inputs, not both.
If low-level outputs are provided from the car stereo, it is recommended that the low-level inputs be used for lowest
distortion and best performance. Use good quality shielded audio cables with RCA plugs at both ends to connect the
stereo to the amplifier and keep the cable lengths to a minimum to avoid noise.
Ifthecarstereodoesnotprovidelow-leveloutputs, theamplifiermaybeconnectedviathespeaker(high-level)outputs
from the stereo. Wire the speaker leads from the car stereo to the 5-pin adaptor harness as shown in the diagram
(shielded cable is not required for this application) and plug the connector into the mating High-Level Input connectors
on the amplifier. Carefully splice and insulate all wire connections.
CAUTION: Use either the low-level or the high-level inputs on the amplifier.
DO NOT use both input levels at the same time.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT WIRING DIAGRAM
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
OUTPUT WIRING DIAGRAM
lNEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.
lNEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
lFAILURE TO WIRE CORRECTLY MAY CAUSE DAMAGE TO THE AMPLIFIER.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
2
3
2
1
After initial set-up, the amplifier should not require any
further adjustment unless there is a change in the car
stereo or speaker system with which it is used.
increase the output from the system. If, however, there
is still output from the amplifier when the car stereo
volume control is at its minimum setting, or the output
levelincreasestoofastwithasmallrotationofthevolume
control, adjust the Gain control to decrease the output
from the system. Once the correct setting is found, these
controls should not require any further adjustment.
1
Power Indicator LED
The Power Indicator LED will illuminate to indicate that
the unit is connected to the battery and that the
Remote Turn-Onterminal is receiving +12 volts, thus
turning on the amplifier.
3
Fuse
The circuitry of the amplifier is protected from damage by
an automotive-type fast-blow fuse. If fuse replacement is
necessary, use only fuses of the same ampere rating as
originally supplied with the unit. The use of fuses with
incorrect ratings may cause serious damage to the
amplifier. If fuses blow consistently, carefully check all
electrical connections to the unit.
2
(Gain) Controls
The amplifier is capable of operating from sources
supplyingawiderangeofinputlevels. TheGaincontrol
should initially be set to the mid-rotation position. If it is
found that there is not enough output even when the
volumecontrolonthecarstereoisatitsmaximumsetting,
adjust the Gain control of the respective channels to
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
90 DAY/12 MONTH LIMITED WARRANTY
Applies to car stereo power amplifiers, equalizers and accessories.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof,
under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
After the initial 90 day period and for a period of 12 months from the date of original purchase, the Company will supply at no charge a
replacement for any defective part(s) but will charge for the labor to repair the product.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated
bill of sale), specification of defect(s), transportation prepaid, to an approved warranty station or the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred
for installation, removal or reinstallation of the product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical
systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF
30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or
representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage
so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l 1-800-645-4994
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
128-5422A
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2001 Audiovox Electronics Corp., Hauppauge, NY 11788
Printed in Korea
128-6097
Download from Www.Somanuals.com. All Manuals Search And Download.
|