Washer-Extractors
Pocket Hardmount
Instructions for
Operating and Programming
the Mechanical Timer
UW35M2
UW60M2
EC001F
Para bajar una copia de estas instrucciones
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232088R3
January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information..............................................................................
Operator Safety.....................................................................................
3
Table of
Contents
Operation............................................................................................. 11
Customer Service.................................................................................. 11
Display Indications............................................................................... 14
Start-up ................................................................................................. 15
Opening Door ....................................................................................... 15
Loading................................................................................................. 15
Supply Dispenser.................................................................................. 16
Cycle Selection..................................................................................... 17
Cycle Execution.................................................................................... 18
Prewash............................................................................................ 18
Wash ................................................................................................ 18
Rinse 1 ............................................................................................. 18
Rinse 2 ............................................................................................. 18
Rinse 3 ............................................................................................. 19
Programming ...................................................................................... 21
Setting the Jumpers............................................................................... 21
1a to 3a............................................................................................. 22
1a to 3a to 3b.................................................................................... 22
1a to 3a to 5a.................................................................................... 23
1a to 3b............................................................................................. 23
1a to 3b to 5b.................................................................................... 23
1a to 5a............................................................................................. 23
1a to 5a to 5b.................................................................................... 23
1a to 5b............................................................................................. 23
2a to 2b............................................................................................. 24
10a to 10b......................................................................................... 24
© Copyright 2007, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232088
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
1. Read all instructions before using the washer.
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, dry-
cleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
20. Replace worn power cords and/or loose plugs.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
13. Use washer only for its intended purpose,
washing textiles.
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
25. Never operate the washer with any guards and/or
panels removed.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
16. Install the washer according to the
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
SW025
WARNING
damage, and may void the warranty.
SW004
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
CAUTION
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
the pipe can be touched.
SW014
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
SW020
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Safety Information
Use manufacturer-authorized spare parts to avoid
safety hazards.
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Safety Information
Operator Safety
Safe Operating Environment
Safe operation requires an appropriate operating
environment for both the operator and the machine. If
questions regarding safety arise, contact the
manufacturer immediately.
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
Environmental Conditions
SW012
●
●
Ambient Temperature. Water in the machine will
freeze at temperatures of 32°F (0°C) or below.
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
Temperatures above 120°F (50°C) will result in
more frequent motor overheating and, in some
cases, malfunction or premature damage to solid
state devices that are used in some models.
Special cooling devices may be necessary.
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
●
●
Water pressure switches are affected by increases
and decreases in temperature. Every 25°F (10°C)
change in temperature will have a 1% effect on
the water level.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
Humidity. Relative humidity above 90% may
cause the machine’s electronics or motors to
malfunction or may trip the ground fault
interrupter. Corrosion problems may occur on
some metal components in the machine.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
●
If the relative humidity is below 30%, belts and
rubber hoses may eventually develop dry rot.
This condition can result in hose leaks, which
may cause safety hazards external to the machine
in conjunction with adjacent electrical
equipment.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
●
Ventilation. The need for make-up air openings
for such laundry room accessories as dryers,
ironers, water heaters, etc., must be evaluated
periodically. Louvers, screens, or other
separating devices may reduce the available air
opening significantly.
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
●
●
Radio Frequency Emissions. A filter is available
for machines in installations where floor space is
shared with equipment sensitive to radio
frequency emissions.
Do not bypass any safety devices in the machine.
Elevation. If the machine is to be operated at
elevations of over 3280 feet (1000 m) above sea
level, pay special attention to water levels and
electronic settings (particularly temperature) or
desired results may not be achieved.
WARNING
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
●
Chemicals. Keep stainless steel surfaces free of
chemical residues.
damage.
SW039
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
Input and Output Services
DANGER
●
Water Pressure. Best performance will be
realized if water is provided at a pressure of 30 –
85 psi (2.0 – 5.7 bar). Although the machine will
function properly at lower pressure, increased fill
times will occur. Water pressure higher than 100
psi (6.7 bar) may result in damage to machine
plumbing. Component failure(s) and personal
injury could result.
Do not place volatile or flammable fluids
in any machine. Do not clean the machine
with volatile or flammable fluids such as
acetone, lacquer thinners, enamel
reducers, carbon tetrachloride, gasoline,
benzene, naptha, etc. Doing so could
result in serious personal injury and/or
damage to the machine.
●
Steam Heat (Optional) Pressure. Best
performance will be realized if steam is provided
at a pressure of 30 – 80 psi (2.0 – 5.4 bar). Steam
pressure higher than 125 psi (8.5 bar) may result
in damage to steam components and may cause
personal injury.
SW002
●
Water Damage. Do not spray the machine with
water. Short circuiting and serious damage may
result. Repair immediately all seepage due to
worn or damaged gaskets, etc.
●
●
For machines equipped with optional steam heat,
install piping in accordance with approved
commercial steam practices. Failure to install the
supplied steam filter may void the warranty.
Machine Location
●
Foundation. The concrete floor must be of
sufficient strength and thickness to handle the
floor loads generated by the high extract speeds
of the machine.
Drainage System. Provide drain lines or troughs
large enough to accommodate the total number of
gallons that could be dumped if all machines on
the site drained at the same time from the highest
attainable level. If troughs are used, they should
be covered to support light foot traffic.
●
Service/Maintenance Space. Provide sufficient
space to allow comfortable performance of
service procedures and routine preventive
maintenance.
●
Power. For personal safety and for proper
operation, the machine must be grounded in
accordance with state and local codes. The
ground connection must be to a proven earth
ground, not to conduit or water pipes. Do not use
fuses in place of the circuit breaker. An easy-
access cutoff switch should also be provided.
Consult installation instructions for specific details.
CAUTION
Replace all panels that are removed to
perform service and maintenance
procedures. Do not operate the machine
with missing guards or with broken or
missing parts. Do not bypass any safety
WARNING
devices.
SW019
Ensure that a ground wire from a proven
earth ground is connected to the ground
lug near the input power block on this
machine. Without proper grounding,
personal injury from electric shock could
occur and machine malfunctions may be
evident.
SW008
Always disconnect power and water supplies before a
service technician performs any service procedure.
Where applicable, steam and/or compressed air
supplies should also be disconnected before service is
performed.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Operation
This manual is designed as a guide to operating and
Customer Service
programming the UW35 and UW60 rigid-mount
washer-extractor equipped with the mechanical timer
control.
If literature or replacement parts are required, contact
the source from whom the machine was purchased or
contact Alliance Laundry Systems LLC at
(920) 748-3950 for the name and address of the
nearest authorized parts distributor.
The manuals, installation instructions, and wiring
diagrams which accompany the machine have been
included with the machine at no charge. Additional
copies are available at a nominal charge.
For technical assistance, call (920) 748-3121
Ripon, Wisconsin.
NOTE: Read this manual thoroughly before
attempting to operate the machine.
A record of each machine is on file with the
manufacturer. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance.
NOTE: Do not use this manual in conjunction with
earlier model UW machines. Do not use technical
literature intended for earlier models when
operating this machine.
NOTE: All information, illustrations, and
specifications contained in this manual are based
on the latest product information available at the
time of printing. We reserve the right to make
changes at any time without notice.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Operation
Machine Familiarization
The machine familiarization guide in Figure 1
identifies major operational features of the UW
washer-extractor.
Supply Valve Box
Supply Dispenser
Door Latch Handle
Control Module
Door Handle
Door Box
Door Hinge
Door Latch
Extension Arm
Shell Front
Rub Rail
Door Latch
Side Panel
FA001G
Figure 1
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Operation
The standard production UW 2-speed model uses a
Theory Of Operation
single drain valve. (A dual drain is available as an
option.) The drain valve is normally open, which
means that it closes only when power is applied, thus
allowing the machine to drain in the event of a power
failure.
The design of the machine emphasizes performance
reliability and long service life. The cylinder, shell,
and main body panels are fabricated of stainless steel.
Electrical controls for the machine are housed in a
separate enclosure located on the top of the machine.
Removing the screws from the module cover, lifting
the cover, and pulling to the rear provides access to the
control module. This module contains the mechanical
timer, contactors, water-level switch, and other control
components.
A door-lock system prevents opening of the stainless
steel door when a cycle is in progress. It also prevents
operation of the machine when the door is open. The
doorbox contains the door-lock microswitch, door-
closed magnetic switch, and the door-unlock solenoid.
The UW35 shaft seal assembly includes two lip seals
integrated into the cast-iron bearing housing. Each seal
has two lips which make contact with a polished
stainless steel bushing mounted to the shaft.
All models use one 2-speed motor to drive the cylinder
via a V-belt drive in both speeds.The cylinder is
supported via the shaft by two bearings. The UW35
uses two ball bearings held in place by a single cast-
iron housing that is bolted to the A-frame. The UW60
uses two flange-mounted, spherical roller bearings
bolted to the A-frame.
The UW60 shaft seal assembly includes a brass collar
held in place on the cylinder shaft with set screws. The
collar has a flange with a ceramic ring which makes
contact with a spring-loaded phenolic face seal
enclosed in a nylon housing mounted on the rear of the
shell. The collar contains two internal O rings which
maintain contact with the cylinder shaft.
The cylinder is constructed with lifters or ribs that lift
the laundry from the bath solution when the cylinder
rotates at slow speed and then allow the laundry to
tumble back into the bath. This mechanical action
accomplishes the washing function. The cylinder is
perforated, allowing the water to drain from within
during the wash and extract steps.
The polypropylene supply dispenser is mounted on the
right side of the washer-extractor, viewed from the
front. The dispenser has 5 supply compartments,
numbered 1–5, starting from the rear of the machine.
The compartments hold plastic supply cups that are
used for for either liquid or dry supplies. A nozzle
flushes supplies from the cups with water at the
appropriate time in the cycle.
On the UW60, a balance switch is installed between
the faces of the A-frame to signal the controls to slow
the machine when a severely out-of-balance load
occurs during extract.
Water enters the machine through electromechanical
water valves controlled by the mechanical timer. The
mechanical timer also controls the drain and door lock.
In addition, the timer selects the water levels according
to the selected cycle. A vacuum breaker is installed in
the water-inlet plumbing to prevent backflow of water.
Liquid supplies can be injected directly into the cups
by a customer-supplied external chemical supply
system. Five hose strain reliefs on top of the supply
dispenser facilitate connection to an external supply
system. A terminal strip inside a compartment
attached to the left side of the control module, viewed
from the rear of the washer-extractor, provides
connection points for external supply signals.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Operation
The amber light labeled “WASH” on the control
module illuminates during fill, heat, and agitation
steps.
Display Indications
Figure 2 shows the control panel for mechanical timer-
controlled machines.
The amber light labeled “SOFTENER” on the control
module illuminates at the beginning of the third rinse
step. This indicates when the machine is flushing
supply dispenser compartments 4 and 5.
The red light labeled “ON” on the control panel
illuminates when a cycle is started and will stay
illuminated until the completion of the cycle.
The amber light labeled “BLEACH” on the control
module illuminates at the beginning of the wash step,
once water level is reached (and cycle temperature has
been reached on auxiliary heat models). This indicates
when the machine is flushing supply dispenser
compartment 3.
The cycle indicator dial on the control module displays
the current cycle step.
The depressed push button on the cycle selector switch
indicates the currently selected cycle.
EC001F
Figure 2
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Operation
Start-up
Loading
Switch the ON/OFF rocker switch on the control
module to the ON position.
CAUTION
Be careful around the open door,
Opening Door
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
Use left hand to press and hold the door unlock button
located on the lower right front of the control panel.
Use right hand to turn door handle clockwise and
SW025
Load the machine to full capacity whenever possible,
but do not exceed the rated dry-weight capacity of the
machine if the fabric to be washed is quite dense,
closely woven, and heavily soiled. Overloading can
result in an inferior wash. The operator may need to
experiment to determine load size based on fabric
content, soil content, and level of cleanliness required.
Partial loads are a waste of energy, water, and
chemicals, and cause greater machine wear than full
loads. Partial loads also increase the possibility of a
severe out-of-balance condition.
WARNING
Never operate the machine with a
bypassed or disconnected out-of-balance
switch. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
MD004J
Figure 3
damage.
SW010
The door will not open if the timer pointer is not in the
vertical position at the top of the dial. If the pointer is
not vertical, the timer must be rapid-advanced until the
timer pointer is in the vertical position. The rapid-
advance procedure is as follows:
When loading is complete, ensure that all fabric is
inside the basket. Then close and lock the door. The
machine should not start or run unless the door is both
closed and locked.
1. Press and hold the START button. The timer will
begin rapid-advancing through the cycle.
CAUTION
Check the door safety interlock daily
before the machine is placed in operation.
2. Release the START button when the timer stops
advancing.
SW024
3. Wait one minute.
4. The door unlock button will be enabled, allowing
the door to be opened.
NOTE: When washing items which may
disintegrate or fragment, such as mop heads or
sponges, use laundry nets to prevent drain
blockage.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Operation
Supply Dispenser
Dry supplies are placed in the supply dispenser
compartment cups prior to the start of each cycle.
Liquid supplies can be injected directly into the supply
dispenser by an external chemical supply system.
NOTE: Supply dispenser compartment cups
should not be removed when an external chemical
injection supply system is attached to the washer-
extractor.
The supply system flushes at preset times in the wash
cycle. Refer to the following tables for more details.
Supply Dispenser Flush Times
Compartment
Time
Prewash and Wash Fill
Wash Fill
1
2
3
4
5
Wash After Fill
Rinse 3 Fill
Rinse 3 Fill
Supply Signal Output Times
Output
Time
Prewash and Wash Fill
Wash Fill
1
2
3
4
5
Wash After Fill
Rinse 3 Fill
Rinse 3 Fill
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Cycle Selection
The push button cycle selector switch on the control
module provides a selection of four complete
automatic cycles. See the table below for more
information.
Press the START button to start the selected cycle.
Mechanical Timer Cycles
Program Water Temperature
Time
(Min)*
Step
Water Level
Permanent
Colors
White
Bright Colors
Press
2
1
Prewash
Drain
High
Warm
Warm
Cold
Cold**
194 °F / 90 °C 140 °F / 60 °C 104 °F / 40 °C
86 °F / 30 °C
Auxiliary Heat Wash Step Temperature †
4
1
Wash
Low
High
High
Hot
Cold
Cold
Warm
Cold
Cold
Warm
Cold
Cold
Cold
Cold
Cold
Drain
0.5
1.5
1
Extract
Rinse 1
Drain
0.5
1.5
1
Extract
Rinse 2
Drain
0.5
1.5
1
Extract
Rinse 3
Drain
High
Cold
Cold
Cold
Cold
4
Extract
Shakeout
0.5
*Cycle times are for the factory-preset jumper configuration and do not include fill and heat times. See the Programming
section for more information.
**Auxiliary heat-equipped models only. Standard models do not have a prewash step in the Bright Colors cycle.
†Auxiliary heat-equipped models only.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Wash
Cycle Execution
After the machine has drained, the drain valve closes
and the water inlet valve(s) opens to fill the machine
with water to low level.
NOTE: The following description is for the factory-
preset program. Prewash times, wash times, final
extract times, fill levels, and water temperatures
may vary depending on jumper configuration. See
the Programming section for more details.
External chemical supply signal output 2 energizes
and supply dispenser compartment 2 flushes
throughout the duration of this fill.
The program timer advances one step every thirty
seconds, except during fills.
External chemical supply signal output 1 energizes
and supply dispenser compartment 1 flushes
throughout the duration of this fill.
Prewash
After the START button has been pressed, the door
unlock button is disabled, the drain valve closes, the
red “ON” indicator light illuminates, and the water
inlet valve(s) opens to fill the machine with water to
high level.
On standard models, the amber indicator light labeled
“BLEACH” illuminates after water level is reached
and remains illuminated for 1 minute. The machine
resumes the washing action once low water level is
reached. External chemical supply signal output 3
energizes and supply dispenser compartment 3 flushes
once low water level is reached.
The door unlock button will remain disabled and the
red “ON” indicator light will remain illuminated for
the duration of the cycle.
On models equipped with auxiliary heat, the timer will
stop and the heating system will activate once the
water level is reached. The timer will resume once
cycle temperature is achieved, illuminating the amber
indicator light labeled “BLEACH,” energizing external
chemical supply signal output 3, and flushing supply
dispenser compartment 3 for 1 minute.
The cylinder rotates clockwise at wash speed during
each fill.
The amber indicator light labeled “WASH” illuminates
during fill, heat, and agitation steps.
External chemical supply signal output 1 energizes
and supply dispenser compartment 1 flushes
throughout the duration of this fill.
When the wash step is completed, the drain valve
opens. After the machine has drained, the machine
performs a 30-second intermediate extract.
When high water level is reached, the water valve(s)
closes and the washing action begins.
Rinse 1
Standard washing action is as follows: 12 seconds
rotation clockwise at wash speed, a
3-second pause, then 12 seconds rotation
counterclockwise at wash speed.
After the intermediate extract step, the machine closes
the drain valve and opens the cold water inlet valve to
fill the machine to high level.
Once high level is reached, the washing action
resumes for 90 seconds.
The Bright Colors cycle uses a gentle washing action:
3 seconds rotation clockwise at wash speed, a 12-
second pause, then 3 seconds rotation
The drain then opens. After the machine has drained,
the machine performs a 30-second intermediate
extract.
counterclockwise at wash speed.
After two minutes of washing action, the drain valve
opens.
Rinse 2
Rinse 2 is identical to rinse 1.
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Operation
Rinse 3
After the second intermediate extract, the machine
closes the drain valve and opens the cold water inlet
valve to fill the machine to high level.
The amber indicator light labeled “SOFTENER”
illuminates at the beginning of the fill, and remains
illuminated for 1 minute.
External chemical supply signal outputs 4 and 5
energize, and supply dispenser compartments 4 and 5
flush for 1 minute during this fill.
Once high level is reached, the washing action
resumes for 90 seconds.
The drain then opens. Once the machine has drained,
the machine performs a four-minute final extract.
A 30-second shakeout is then executed, completing the
cycle.
A 30-second delay is in effect after the “ON” light
goes off before the door unlock button is enabled.
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Notes
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
The wash cycle program in machines equipped with a
mechanical timer can be modified to a limited extent.
The following changes can be made:
Setting the Jumpers
WARNING
●
●
The prewash time may be set to 2 minutes, 4
minutes, or omitted altogether.
Attempting jumper configurations other
than those described in this manual may
result in personal injury and/or equipment
The wash time may be set to either 4 minutes or 8
minutes. The water level for the wash step may
be set to either low or high.
damage, and may void the warranty.
SW041
●
●
The water temperature for the rinses may be set
to either cold or warm.
NOTE: The following procedures must be
performed by a qualified electrician familiar with
the construction and operation of this type of
machinery.
The final spin time may be set to either 2 minutes
or 4 minutes.
1. Disconnect power to the machine.
WARNING
This machine must be installed, adjusted,
and serviced by qualified electrical
2. Remove the screws securing the control module
cover to the control module.
3. Lift the control module cover and slide cover
towards the rear of the machine.
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
4. The mechanical timer is located in the control
module. The odd-numbered side of the timer is
used to change the duration of individual cycle
damage, and may void the warranty.
Eleven permissible jumper configurations are
available for changing the cycle time. See the
table below.
SW004
WARNING
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
19b
17b
15b
13b
11b
9b
19
17
15
13
11
9
19a
17a
15a
13a
11a
9a
troubleshooting. Disconnect power from
the machine before removing the control
box cover, and before attempting any
service procedures.
SW005
7b
7
7a
5b
5
5a
3b
3
3a
1b
1
1a
Figure 4
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Mechanical Timer Cycle Time Options
Final
Spin
Cycle
Time*
Jumper Setting
Prewash
Wash
Rinse 1
Rinse 2
Rinse 3
4
4
8
4
4
4
4
4
8
8
8
8
8
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
4
4
4
2
4
2
4
2
4
2
2
27.5
23.5
18.5
16.5
21.5
19.5
22.5
20.5
25.5
23.5
25.5
None
1a to 3a
--
--
2
1a to 3a to 3b
1a to 3a to 3b to 5b
1a to 3a to 5a**
1a to 3a to 5a to 5b
1a to 3b
2
--
--
2
1a to 3b to 5b
1a to 5a
2
1a to 5a to 5b
1a to 5b
4
*Cycle times do not include fill or heat times.
**Factory setting.
Table 1
5. If access to the odd-numbered side of the timer is
limited, remove the timer bracket mounting
screws and rotate the timer.
1a to 3a
This jumper configuration shortens the wash step
6. Install or remove jumpers to achieve the desired
the permissible jumper combinations.
5b
3b
1b
5
3
1
5a
3a
1a
NOTE: Do not remove the cover from the
mechanical timer. Removing this cover will void the
warranty.
Figure 6
No Jumpers Installed on the Board
1a to 3a to 3b
Removing all the jumpers extends the cycle time,
This configuration eliminates the prewash step
and shortens the wash step from 8 minutes to 4
5b
3b
1b
5
3
1
5a
3a
1a
5b
3b
1b
5
3
1
5a
3a
1a
Figure 5
Figure 7
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Programming
Figure 11
1a to 3a to 3b to 5b
This configuration eliminates the prewash step,
shortens the wash stepfrom 8 minutes to 4
minutes, and shortens the final spin time from 4
1a to 3b to 5b
This configuration eliminates the prewash step
and shortens the final spin time from 4 minutes to
5b
3b
1b
5
3
1
5a
3a
1a
5b
3b
1b
5
3
1
5a
3a
1a
Figure 8
Figure 12
1a to 3a to 5a
1a to 5a
This is the factory-preset jumper
This configuration shortens the prewash step
configuration.This configuration shortens the
prewash step from 4 minutes to 2 minutes and
shortens the wash step from 8 minutes to 4
5b
3b
1b
5
3
1
5a
3a
1a
5b
3b
1b
5
3
1
5a
3a
1a
Figure 13
1a to 5a to 5b
Figure 9
This configuration shortens the prewash step
from 4 minutes to 2 minutes and shortens the
final spin time from 4 minutes to 2 minutes. See
1a to 3a to 5a to 5b
This configuration shortens the prewash step
from 4 minutes to 2 minutes, shortens the wash
step from 8 minutes to 4 minutes, and shortens
the final spin time from 4 minutes to 2 minutes.
5b
3b
1b
5
3
1
5a
3a
1a
5b
3b
1b
5
3
1
5a
3a
1a
Figure 14
1a to 5b
Figure 10
This configuration shortens the final spin time
1a to 3b
This configuration eliminates the prewash step.
5b
3b
1b
5
3
1
5a
3a
1a
5b
3b
1b
5
3
1
5a
3a
1a
Figure 15
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
7. The even-numbered side of the program timer
can be configured with jumpers to adjust the
rinse temperature or to change the water level for
the wash step. Either or both even-side jumper
configurations may be used in conjunction with
any of the 11 permissible odd-side jumper
12b
10b
8b
12
10
8
12a
10a
8a
Figure 18
NOTE: This jumper configuration will cause the
timer to advance once low water level is reached.
The fill valves will remain open until high water
level is reached.
20b
18b
16b
14b
12b
10b
8b
20
18
16
14
12
10
8
20a
18a
16a
14a
12a
10a
8a
8. Replace the timer bracket screws if they were
removed in step 5.
9. Replace the control module cover and mounting
screws.
10. Reconnect power to the machine.
6b
6
6a
4b
4
4a
2b
2
2a
0b
0
0a
Figure 16
options available.
2a to 2b
This jumper configuration changes the fill
temperature for the rinses from cold to warm for
4b
2b
0b
4
2
0
4a
2a
0a
Figure 17
10a to 10b
This jumper configuration changes the water
level for the wash segment from low to high for
F232088
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
22
|