™
OWNERS
MANUAL
Model No.
45-03621
45-03622
42" ROUGH CUT
TRAILMOWER
IMPORTANT: BATTERY REQUIRED!! The battery is NOT included
with the deck but must be purchased separately. A 12 volt lawn tractor
battery with 260/300 cold cranking amps and dimensions of 6-1/8"H x
7-5/8"L x 5-1/8"W is recommended to operate the machine.
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
• Safety
• Assembly
• Operation
• Maintenance
• Parts
PRINTED IN USA
FORM NO. 49463 (REV. 10/01/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
Safe Operation Practices for Tow Behind Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND
THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
I. GENERAL OPERATION
II. SLOPE OPERATION
•
•
•
•
•
Read, understand, and follow all instructions in the manual and on
the machine before starting.
Read this operator’s manual carefully. Become familiar with the
controls and know how to operate your mower properly.
Only allow responsible adults, who are familiar with the instructions,
to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc., which
could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing. Stop
machine if anyone enters the area.
Slopes are a major factor related to loss-of-control and tip over
accidents, which can result in severe injury or death. All slopes
require extra caution. If you feel uneasy on it, do not mow it.
DO:
•
•
•
Mow up and down slopes, not across.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts, or bumps. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
•
•
•
•
Use slow speed. Choose a low gear so that you will not have to stop
or shift while on the slope.
Follow the tractor manufacturer’s recommendations for wheel
weights or counterweights to improve stability.
Keep all movement on the slopes slow and gradual. Do not make
sudden changes in speed or direction.
Avoid starting or stopping on a slope. If tires lose traction, disengage
the blades and proceed slowly straight down the slope.
•
•
Never carry passengers.
Do not mow in reverse unless absolutely necessary. Always look
down and behind before and while backing.
Slow down before turning.
Never leave a running machine unattended.Always turn off blades,
and stop engine.
•
•
•
•
•
Turn off blades when not mowing.
Mow only in daylight or good artificial light.
Do not operate the machine while under the influence of alcohol
or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine into a
trailer or truck.
Do not attempt to operate your tractor or mower when not in
drivers seat.
Disengage power to mower, stop engine when transporting or not
in use.
Exercise special care when mowing around fixed objects in order
to prevent the blades from striking them. Never deliberately run
tractor or mower onto or over any foreign object.
Use mower only as the manufacturer intended and as described
in this manual.
Do not operate mower if it has been dropped or damaged in any
manner. Always have damage repaired before using your mower.
Always wear safety glasses or eye shields when starting and while
using your mower.
Dress properly. Do not operate mower when barefoot or wearing
open sandals. Wear only solid shoes with good traction when
mowing.
Always make cutting height adjustments before starting your
mower. New attempt to do this while the engine is running.
Keep your eyes and mind on your mower and the area being cut.
Do not let other interests distract you.
DO NOT:
•
•
•
Do not turn on slopes unless necessary, and then, turn slowly and
gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments. The mower
could suddenly turn over if a wheel is over the edge of a cliff or
ditch, or if an edge caves in.
•
•
•
•
•
Do not mow on wet grass. Reduced traction could cause sliding.
Ill. CHILDREN
Tragic accidents can occur if the operator is not alert to the presence
of children. Children are often attracted to the machine and the mowing
activity. Never assume that children will remain where you last saw
them.
•
•
•
•
•
Keep children out of the mowing area and under the watchful care
of another responsible adult.
Be alert and turn machine off if children enter the area.
Before and when backing, look behind and down for small
children.
Never carry children. They may fall off and be seriously injured or
interfere with safe machine operation.
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs, trees, or
other objects that may obscure vision.
•
•
•
•
•
•
•
•
•
Do not put hands or feet near or under rotating parts. Keep clear
of the discharge opening at all times.
•
•
•
Before cleaning, inspecting, or repairing your mower, stop the
engine and make absolutely sure the blade and all moving parts
have stopped. Then disconnect the spark plug wire and keep it
away from the spark plug to prevent accidental starting.
Do not operate your mower if it vibrates abnormally. Excessive
vibration is an indication of damage or unbalanced blades. Stop
the engine, safety check for the cause of the vibration and repair
as required.
Never operate your mower without proper guards, plates, or other
safety devices in place.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IV. SERVICE
Look for this symbol to point out
important safety precautions. It
means CAUTION!! BECOME
ALERT!! YOUR SAFETY IS
INVOLVED
•
Use extra care in handling gasoline and other fuels. They
are flammable and vapors are explosive.
-- Use only an approved container.
-- Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling. Do not
smoke.
-- Never refuel the machine indoors.
-- Never store the machine or fuel container inside
where there is an open flame, such as a water
heater.
Never run a machine inside a closed area. Keep nuts and
bolts, especially blade attachment nuts, tight and keep
equipment in good condition.
CAUTION: Always disconnect spark
plug wire and place wire where it
cannot contact spark plug in order
to prevent accidental starting when
setting up, transporting, adjusting or
making repairs.
•
•
•
Never tamper with safety devices. Check their proper
operation regularly.
Keep machine free of grass, leaves, or other debris build-
up. Clean oil or fuel spillage. Allow machine to cool before
storing.
•
•
•
•
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
Never make adjustments or repairs with the engine
running.
Mower blades are sharp and can cut. Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service as
required.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS OF PARTS BAG
SHOWN FULL SIZE
A
B
C
D
E
H
G
F
NOT SHOWN FULL SIZE
K
J
I
REF. QTY.
DESCRIPTION
Hex Bolt, 1/2" x 7"
Hex Bolt, 1/4" x 7-1/2"
Hex Bolt, 5/16" x 3/4"
Hex Bolt, 1/4" x 3/4"
REF. QTY.
DESCRIPTION
Hex Nylock Nut, 5/16"
Hex Nut (SEMS), 1/4"
Clip, 3/8"
Plastic Nut
Key
A
B
C
D
E
F
1
2
2
2
2
1
G
H
I
2
2
2
2
1
J
Screw, Self Tapping #10 x 1/2"
Hex Nylock Nut, 1/2"
K
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
INSTALL TOWBAR TUBE TO REAR
QUADRANT
•
Place Towbar Tube into Rear Quadrant, align holes and
insert 3/8 x 2-3/4 Hex Bolt through quadrant and rear
hole of Tube.
•
Secure tightly with 3/8 Hex Lock Nut and then loosen
1/4 turn to allow Tube to pivot freely inside Rear
Quadrant.
•
•
Insert 3/8 X 2-3/4 Bolt and 3/8 Flat Washer into slot in
Rear Quadrant and into hole in Towbar Tube.
Secure Tightly with 3/8 Flat Washer and 3/8 Hex Lock
Nut, then loosen 1/4 turn to allow Tube to pivot freely
inside Rear Quadrant.
NOTE: Towbar Tube must pivot freely inside Rear Quadrant
when Latch is pulled from notch.
INSTALL CLUTCH CABLE TO TOWBAR TUBE
•
•
Place Clutch Cable forward along Towbar Tube.
Spread ends of two Cable Clips and place around
Clutch Cable.
•
•
Place Clutch Cable on top of Towbar Tube and align
Cable Clips with bolt holes in Towbar Tube.
Secure with two #10 Screws.
INSTALL BATTERY
Your Trail Mower requires a 12 volt battery to operate. The
battery is NOT included with the unit. It must be purchased
separately.
•
•
•
Remove four screws and the Battery Cover from the
Mower and set them aside.
Install two Plastic Nuts into the square holes in the
Mower Deck under the Battery Cover.
Place the Battery on the Mower Deck between the two
Plastic Nuts.
Place the Battery Hold Down on top of the Battery.
Secure the Battery to the Mower Deck with two
1/4 x 7-1/2 hex bolts.
Open the terminal access doors on the Battery Hold
Down.
INSTALL CLUTCH CABLE TO CLUTCH LEVER
•
Remove outer 5/16 Nut from end of Clutch Cable
Housing. (See Fig. 1)
•
•
Turn inner 5/16 Nut to bottom of thread.
Insert Cable and outer 5/16 Nut through slotted hole
in Cable Guide of Hitch Assembly. The outer 5/16 Nut
musts be cocked sideways to insert through slotted hole
of Cable Guide.
•
•
•
•
•
•
Reinstall outer 5/16 Nut to the cable housing to secure
Cable Harness to Cable Guide.
Install Mounting Anchor of Clutch Cable to Clutch Lever
using Clevis Pin and Hair Cotter Pin.
Connect the Red Wire to the positive (+) battery terminal
using a 1/4 x 3/4 hex bolt and 1/4 SEMS nut. Tighten
securely.
•
Connect the Black Wire to the negative (-) battery
terminal using a 1/4 x 3/4 hex bolt and 1/4 SEMS nut.
Tighten securely.
•
•
Close the terminal access doors.
Replace Battery Cover and secure it with the four
screws.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TERMINAL ACCESS DOORS
1/4 X 3/4 HEX BOLT &
1/4 HEX NUT (SEMS)
BATTERY
COVER
BLACK WIRE
SCREW (4)
-
+
BATTERY HOLD DOWN
1/4 X 7-1/2 HEX BOLT
PLASTIC NUT
RED WIRE
1/4 X 7-1/2
HEX BOLT
REAR QUADRANT
3/8 X 2-3/4 HEX BOLT
3/8 FLAT WASHER
CLUTCH LEVER
#10 SCREW (2)
CABLE CLIP (2)
3/8 FLAT WASHER
3/8 HEX LOCK NUT
1/4 X 3/4 HEX BOLT
HITCH ASSEMBLY
CLUTCH CABLE
5/16 HEX NUT (2)
MOUNTING ANCHOR
FIG. 1
1/4" HEX LOCK NUT
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
CLUTCH CABLE ADJUSTMENT
INNER NUT
•
Remove four screws from Rear Drive Cover. Lay aside
cover and screws.
•
•
Place Clutch Lever in “DISENGAGED" position
The Cable should be under slight tension but should
not pull the Clutch Lever more than 1/8" away from the
Switch Body.
NOTE: If the Plunger extends more than 1/8" out from
the switch body, the cable tension is too tight and the
Engine will not start.
OUTER NUT
TO INCREASE CABLE TENSION
•
Place Blade Clutch Lever in the “DISENGAGED"
position.
•
•
Loosen the inner nut on the Clutch Cable.
Tighten the outer nut on the Clutch Cable.
TO DECREASE CABLE TENSION
•
Place Blade Clutch Lever in the “DISENGAGED"
position.
•
•
•
Loosen the outer nut on the Clutch Cable.
Tighten the inner nut on the Clutch Cable.
Repeat the above procedure until you have the correct
tension.
SWITCH
BODY
IDLER
PULLEY
ENGINE
PULLEY
1/8"
PLUNGER
CLUTCH LEVER
BLADE
PULLEY
FOUR
SCREWS
REAR DRIVE
COVER
CLUTCH LEVER
FIG. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
INSTALL REAR ROLLER TO DECK
•
Install Rear Roller Mounting Bracket to rear of deck
using two 5/16 x 3/4 Hex Bolts and two 5/16 Hex
Nylock Nuts. (See Fig. 3.)
•
•
Install Roller to Rear Roller Bracket using 1/2 x 7 Hex
Bolt and 1/2 Hex Nylock Nut.
Make sure Roller turns freely on Bolt.
5/16 X 3/4 HEX BOLTS
AND 5/16 HEX LOCK NUTS
REAR ROLLER
MOUNTING BRACKET
ROLLER
1/2 X 7 HEX BOLT
1/2 HEX LOCK NUT
FIG. 3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
HEIGHT ADJUSTMENT STRAP
IGNITION
KEY SWITCH
MOWER BLADE
CLUTCH LEVER
HEIGHT ADJUSTMENT
LIFT LEVER
TOW HITCH OFFSET
ADJUSTMENT
HEIGHT
ADJUSTMENT
STRAP
TOW BAR HEIGHT
ADJUSTMENT
THROTTLE CONTROL
FIG. 4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TRACTOR
HITCH PIN
OR MOWER
CLEVIS PIN
HAIR COTTER PIN
REMOVE MOWER CLEVIS
PIN FROM THIS HOLE
FIG. 5
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
HAIR COTTER PIN
HEIGHT ADJUSTMENT STRAP
LOCATING PIN
CLEVIS PIN
HEIGHT ADJUSTMENT
LIFT LEVER
HAIR COTTER PIN
CUTTING
HEIGHTS
1-1/2"
2"
2-1/2"
3"
3-1/2"
4"
4-1/2"
5"
TOW BAR
TOW BAR
ADJUSTMENT
CUTTING HEIGHT
GROUND LEVEL
FIG. 6
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
This mower has been designed to run offset from the
center of the tow vehicle. This allows the operator to drive
along side high brush with the tow vehicle while cutting
down the brush beside him. The adjustable hitch gives
you three offset cutting positions plus straight behind for
narrow paths.
MODEL 45-0362
The adjustable hitch of this mower can be set in seven
positions including straight and offsets of 9", 17" and 23"
on both sides. (See Fig. 7)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
WHEEL PIVOT 3
SPINDLE 2
WHEEL 2
SWIVEL 2
WHEEL 2
WHEEL PIVOT 3
QUADRANT 3
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
BLADE CARE AND SERVICE
BLADE ASSEMBLY
CAUTION:
DO NOT HANDLE MOWER BLADES WITH
BARE HANDS. CARELESS OR IMPROPER
HANDLING MAY RESULT IN SERIOUS
INJURY.
BLADE CARE
For best results mower blades must be kept sharp. The
blades can be sharpened with a file or on a grinding
wheel. Do not attempt to sharpen blades while they are
still on the mower.
BLADE SERVICE (Refer to fig. 9)
TO REMOVE BLADE ASSEMBLY FROM DECK
•
•
•
Remove cotter pin from the spindle shaft.
Remove nut and washer from the spindle shaft.
Pull blade assembly off the spindle shaft. (Watch for a
key in the spindle shaft.)
FIG. 9
TO REMOVE BLADES FROM BLADE ASSEMBLY.
WARNING:
•
•
•
Remove cotter pin from the blade bolt.
Remove nut from the blade bolt.
Remove blade from the blade assembly.
SHUT OFF MOWER ENGINE AND REMOVE
SPARK PLUG WIRE FROM SPARK PLUG
BEFORE MAKING ANY ADJUSTMENTS OR
REPAIRS TO THE MOWER.
BLADE SHARPENING
•
Blades can be sharpened with a file or grinding
wheel.
NOTE: When sharpening blades take care to maintain blade
balance.Sharpen both blades equally even if one blade does
not need to be sharpened.Check balance by weighing each
blade to make sure they are equal in weight.
CLEANING THE MOWER
Water pressure from a garden hose will remove fresh
clippings from the underside of the mower. Clean mower
after each mowing.
CAUTION:
IF YOUR BLADE BOLTS SHOW WEAR,
REPLACE THEM WITH FACTORY
REPLACEMENTS ONLY.
DAILY MAINTENANCE
Make sure all nuts and bolts are tight, cotter pins and
retainer springs are secure. Keep blades sharp. Observe
all Safety Precautions. Keep mower well lubricated.
TO REINSTALL BLADES
•
Assemble a blade bolt through a flat washer, a blade
and then another flat washer.
REPAIR PARTS
•
Assemble the bolt through the hole in the stump plate
and the blade hub assembly.
Your rotary mower has been produced with components
designed for your unit. Although standard V-belts,
bearings, blades, pulleys, etc. may look like parts used on
your rotary mower, while similar in appearance many are
of a different construction and could in some cases cause
a malfunction in the operation of the machine.
•
•
•
Assemble a flat washer and nut onto the blade bolt.
Tighten nut, then loosen just until blade can pivot.
Install a cotter pin to secure the nut.
TO REINSTALL BLADE ASSEMBLY TO MOWER
•
•
•
•
Reinstall key in spindle shaft, if necessary.
Install the blade assembly onto the spindle shaft.
Secure with flat washer and nut.
Torque the spindle shaft and nut to 100 FT. LBS. and
secure with a hair cotter pin.
For continued satisfactory performance use only repair
parts supplied by the manufacturer. See the dealer where
the mower was purchased for factory replacement parts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
CLUTCH CABLE ADJUSTMENT
INNER NUT
•
Remove four screws from Rear Drive Cover. Lay aside
cover and screws.
•
•
Place Clutch Lever in “DISENGAGED" position
The Cable should be under slight tension but should
not pull the Clutch Lever more than 1/8" away from the
Switch Body.
NOTE: If the Plunger extends more than 1/8" out from
the switch body, the cable tension is too tight and the
Engine will not start.
OUTER NUT
TO INCREASE CABLE TENSION
•
Place Blade Clutch Lever in the “DISENGAGED"
position.
•
•
Loosen the inner nut on the Clutch Cable.
Tighten the outer nut on the Clutch Cable.
TO DECREASE CABLE TENSION
•
Place Blade Clutch Lever in the “DISENGAGED"
position.
•
•
•
Loosen the outer nut on the Clutch Cable.
Tighten the inner nut on the Clutch Cable.
Repeat the above procedure until you have the correct
tension.
SWITCH
BODY
IDLER
PULLEY
ENGINE
PULLEY
1/8"
PLUNGER
CLUTCH LEVER
BLADE
PULLEY
FOUR
SCREWS
REAR DRIVE
COVER
CLUTCH LEVER
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
INSTALLING NEW V-BELT
V-BELT REPLACEMENT
•
V-belt must be replaced if it becomes stretched to the
point that it can no longer be adjusted, or if it becomes
frayed or otherwise can not function properly.
Move Blade Clutch Lever to the “DISENGAGED"
position.
•
•
Feed new V-belt between the two belt guides at the
Engine Pulley.
Place V-belt up and around the Engine Pulley. Check to
make sure the V-belt is seated properly in the groove of
the Engine Pulley.
•
•
•
Place V-belt along inside of Idler Pulley.
Wrap V-belt down around Blade Pulley, placing Belt
inside of Rear Belt Guides.
Reinstall V-belt Keeper Rod and secure with Small Hair
Pin. Check to make sure V-belt is over top of Keeper
Rod.
Reposition and retighten two Rear Belt Guides at the
rear of the Blade Pulley. Leave approximately 1/16"
between Guides and Pulley.
Reinstall Clevis Pin and Hair Pin into Clutch Cable.
Reinstall Front Drive Cover and Rear Drive Cover.
CAUTION:
DISCONNECT SPARK PLUG WIRE
•
•
REMOVING OLD V-BELT
•
•
•
•
Remove Rear Drive Cover.
Remove Front Drive Cover.
Remove Hair Pin and Clevis Pin from Clutch Cable.
Loosen two Rear Belt Guides and pivot them away
from Blade Pulley.
•
•
•
•
Remove V-belt from around Blade Pulley.
Remove one small Hair Pin from Belt Keeper Rod and
slide Belt Keeper Rod to the side.
•
Pull V-belt down from around Engine Pulley and
remove V-belt from Mower.
BELT GUIDES
HAIRPIN AND CLEVIS PIN
BLADE PULLEY
REAR BELT GUIDES
ENGINE PULLEY
BELT KEEPER ROD
V-BELT
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
21
Download from Www.Somanuals.com. All Manuals Search And Download.
42" ROUGH CUT TRAILMOWER - MODELS 45-03621 & 45-03622
22
Download from Www.Somanuals.com. All Manuals Search And Download.
42" ROUGH CUT TRAILMOWER - MODELS 45-03621 & 45-03622
ITEM PART NO. DESCRIPTION
ITEM PART NO. DESCRIPTION
1.
HA24255
HA24378
HA23193
HA24292
HA24293
HA3090
HA24294
HA24295
45100
MOWER DECK
48.
50.
51.
53.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
74.
75.
76.
77.
78.
79
HA115321
43555
SCREW 5/16-18 X 5/16 SOC. SET
WASHER 7/16" LOCK
2.
GUARD WHEEL
3.
SCREW 3/8-16 X 1-1/4 THD. FORMING
BRACKET BELT GUIDE
ROD BELT GUIDE
HA181668
25265
BOLT 7/16-20 X 1-1/4 HEX HEAD
COVER, FRONT DRIVE
BOLT 5/16-18 X 3/4 HEX HEAD
NUT 5/16-18 HEX NYLOCK
COVER, REAR DRIVE
4.
5.
43182
6.
PIN HAIR COTTER
47810
7.
V-BELT (B SEC. 60" O.C.)
CHANNEL CLUTCH LEVER
BOLT 1/2-13 X 4" HEX HEAD
WASHER 1/2 FLAT
25264
8.
HA23732
HA24317
HA163318
HA23733
48837
TANK GASOLINE
9.
PLATE FUEL TANK
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
HA120396
43262
SCREW 1/4-14 X 7/8 TAPPING PAN HEAD
CAP GASOLINE TANK
NUT 1/2-13 HEX LOCK
WASHER FLAT
HA14232
HA24296
44101
HOSE FUEL TANK LONG
SPARK ARRESTOR KIT
CLAMP FUEL LINE
ROD CLUTCH LINK
392154
HA23792
PIN, COTTER 3/32" X 3/4"
WASHER FLAT 5/16" STD. WRT.
SPRING CLUTCH
43081
HA9411666 SCREW #10-16 SELF TAPPING
HA24297
49165
48095
PIPE
CLUTCH CABLE ASSY
STRAP, CLUTCH ADJUSTING
BOLT, 1/4-20 X 1" HEX HEAD
BOLT, HEX 1/4-20 X 3/4"
BRACKET INTERLOCK MOUNTING
SWITCH INTERLOCK
NUT, HEX 1/2-13 JAM NYLOCK
NUT #10-24 HEX
48096
CAP
25292
HA24310
HA12138
HA12315
HA12314
HA24431
HA126145
43982
BRACKET ROLLER
ROLLER MOWER
DECAL DANGER (HAND)
DECAL DANGER
43661
43012
25262
HA23199
48115
DECAL OPERATION/CAUTION
BOLT 1/2-13 X 7" HEX HEAD
PIN, CLEVIS 1/4" X 5/8"
BELT GUIDE
712-0121
47078
SCREW #10-24 X 3/4"
SCREW 1/4-20 WASHER HEAD
CLIP
HA22981
HA24298
49156
48840
SPRING RETURN
ROD, CABLE GUIDE
NUT 1/4-20 HEX NYLOCK
WHEEL BEARING
SOLENOID
48298
HA24300
HA24301
HA4143
HA137258
46272
WHEEL MOUNTING BRACKET L.H.
WHEEL MOUNTING BRACKET R.H.
WASHER FLAT
47189
80.
81.
82.
83.
84.
85.
86.
87.
88.
89.
90.
91.
92.
93.
94.
44488
HA23754
HA23749
HA23750
HA23757
HA23752
25286
PIN COTTER 3/16" X 1-3/4"
TIRE
STARTER SWITCH
SWITCH MOUNTING NUT
SWITCH COVER
HA23229
HA24309
HA6979
43020
CAP HUB
STRAP ADJUSTING
KEY
WASHER FLAT
PLATE, SWITCH MOUNTING
THROTTLE
BOLT 1/2-13 X 1-1/2 HEX HEAD
NUT 1/2-13 HEX JAM
PIN LOCATING
49201
43019
45040
SCREW, #10-24 X 1/2
LOCK WASHER, #10
BATTERY HOLD DOWN
BOLT, BATTERY
HA23220
47134
736-0722
49198
PIN HAIR COTTER .08" X 1.58"
CHAIN DEFLECTOR
HA24311
HA24312
HA24313
HA9131
25428
49199
ROD CHAIN
49200
NUT, PLASTIC
BRACKET CHANNEL
SCREW SELF THREADING
PLATE ENGINE MOUNTING
25287
BATTERY COVER
SCREW, 1/4-20 X 1/2 HEX HEAD
48840
280H070130E1* ENGINE, 14.5 HP
*
Order engine repair parts from your nearest Briggs & Stratton
HA24457
HA3073
PULLEY
dealer.
KEY 1/4" SQ. X 1"
23
Download from Www.Somanuals.com. All Manuals Search And Download.
42" ROUGH CUT TRAILMOWER - MODELS 45-03621 & 45-03622
40
23
9
12
11
4
34
8
6
42
5
7
4
21
22
22
2
3
1
20
15
18
33
32
13
14
15
16
17
39
18
21
30
31
28
19
23
26
24
25
37
41
5
4
36
28
27
35
27
38
43
28
10
15
28
29
24
Download from Www.Somanuals.com. All Manuals Search And Download.
42" ROUGH CUT TRAILMOWER - MODELS 45-03621 & 45-03622
ITEM
PART NO.
DESCRIPTION
1.
64906
IDLER MOUNTING BRACKET
IDLER ARM
2.
64899
3.
24472
BUSHING
4.
43070
WASHER FLAT
5.
43003
WASHER 3/8" LOCK
BOLT 3/8-16 X 1-1/2" HEX HEAD (SCOTCH GRIP)
SPACER
6.
49640
7.
49148
8.
HA21341
43432
IDLER PULLEY (FLAT)
BOLT 3/8-16 X 2-1/2" HEX HEAD
NUT 3/8-16 HEX LOCK
GUIDE BELT
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
43082
HA22981
HA22224
43087
SCREW 3/8-16 X 3/4 SELF TAPPING
BOLT 3/8-16 X 1-1/4" HEX HEAD
WASHER FLAT
HA15200
HA21362
HA24367
HA24278
HA24280
64913
NUT 3/8-16 NYLOCK
GREASE FITTING
HUB (WITH STUDS)
BEARING
HUB BLADE
49149
SHAFT SPINDLE
HA24282
HA3073
HA456151
HA427639
47063
SEAL O-RING
KEY 1/4" SQ X 1"
WASHER 13/16 X 1-1/2 X .134 FLAT
NUT 3/4-16 SLOTTED HEX
PIN, COTTER 5/32"
DISC BLADE MOUNTING
BLADE
HA24624
HA24288
HA24625
HA24592
HA137258
HA24593
43353
WASHER - FLAT
BOLT - 7/8-9 X 2-1/4 HEX BOLT
PIN 3/16 X 1-3/4 COTTER
NUT 7/8-9 SLOTTED HEX
WASHER 1/2 MED. LOCK
NUT 1/2-20 HEX
HA120371
65102
PULLEY SPINDLE
64902
BRAKE
49155
TRUNNION
49160
BRAKE ROD
HA20186
49624
SPRING
SPACER, BEARING
NUT, 3/4-16 NYLOCK
BOLT, 3/8-16 X 1" HEX HEAD (SCOTCH GRIP)
WASHER, 5/16"
49674
49681
43081
43015
NUT, HEX 3/8-16
25
Download from Www.Somanuals.com. All Manuals Search And Download.
42" ROUGH CUT TRAILMOWER - MODELS 45-03621 & 45-03622
ITEM
PART NO.
DESCRIPTION
ITEM
PART NO.
DESCRIPTION
16.
17.
19.
20.
21.
22.
23.
24.
25.
26.
27.
29.
30.
31.
43982
PIN, CLEVIS 1/4 X 5/8
PIN, HAIR COTTER 1-5/8
DECAL CLUTCH LEVER
BRACKET DRAWBAR ADJUSTMENT
DRAWBAR SWIVEL
1.
25273
TUBE DRAWBAR (MODEL 45-0361)
STRAP HITCH
HA3090
HA23265
64910
2.
HA24441
HA20186
44180
3.
SPRING EXTENSION
4.
BOLT 5/16-18 X 2" HEX HEAD
NUT, HEX 5/16-18 NYLOCK
HITCH ASSEMBLY
HA24326
HA5074
HA15200
43003
5.
47810
FITTING GREASE
6.
64909
WASHER
8.
43509
BOLT 3/8-16 X 2-3/4 HEX HEAD
NUT 3/8 NYLOCK JAM
NUT, HEX 3/8-16 NYLOCK
PIN CLEVIS
WASHER 3/8 LOCK
9.
1038
43087
BOLT 3/8-16 X 1-1/4 HEX HEAD
PIN CLEVIS
10.
11.
12.
13.
14.
15.
HA21362
HA23636
47134
HA24330
HA3341
HA23761
HA9411666
49193
PIN HAIR COTTER, 5/32"
CLIP HOSE 3/8"
PIN HAIR COTTER .08 X 1.58
LEVER CLUTCH
49157
SCREW #10-16 X 1/2 SELF TAPPING
WIRE HARNESS (See page 27)
43062
BOLT 3/8-16 X 1-1/2 HEX HEAD
SPRING COMPRESSION
HA19445
26
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
© 2004 Agri-Fab, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
ACDelco Home Safety Product LG08 User Manual
Adaptec Computer Hardware 1220SA User Manual
Aiphone Home Theater Screen KCW M User Manual
Alpine CD Player CDE 9843 User Manual
Altec Lansing Portable Speaker 1218A User Manual
Altec Lansing Speaker VS3121 User Manual
American Audio Music Mixer XLT 1200 User Manual
AMX TV Cables CB TP12 User Manual
Atlona Switch AT SDI81 User Manual
Audiovox Automobile Alarm PRO9246ft3 User Manual