Acer Altos G520 series
User’s guide
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
Notices
FCC notice
Class A devices do not have an FCC logo or FCC IDE on the label. Class B devices
have an FCC logo or FCC IDE on the label. Once the class of the device is
determined, refer to the following corresponding statement.
Class B equipment
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the device and receiver
Connect the device into an outlet on a circuit different from that to which
the receiver is connected
•
Consult the dealer or an experienced radio/television technician for help
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class A or Class B limits may be attached to this equipment.
Operation with noncertified peripherals is likely to result in interference to
radio and TV reception.
Caution! Changes or modifications not expressly approved by the
manufacturer could void the user’s authority, which is granted by
the Federal Communications Commission, to operate this server.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Use conditions
This part complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class A/Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Laser compliance statement
The CD-ROM drive in this server is a laser product. The CD-ROM drive’s
classification label (shown below) is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO
BEAM.
Download from Www.Somanuals.com. All Manuals Search And Download.
v
Important safety instructions
Read these instructions carefully. Save these instructions for future reference.
1
2
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
3
4
Do not use this product near water.
Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious damage to the product.
5
Slots and openings on the back or bottom side of the chassis are provided
for ventilation; to ensure reliable operation of the product and to protect
it from overheating, these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product should never be placed near or
over a radiator or heat register, or in a built-in installation unless proper
ventilation is provided.
6
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
7
8
Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
9
Never push objects of any kind into this product through chassis slots as
they may touch dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the
product.
10 Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks. Refer all
servicing to qualified service personnel.
11 Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a
b
c
When the power cord or plug is damaged or frayed
If liquid has been spilled into the product
If the product has been exposed to rain or water
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
d
If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are covered
by the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive work
by a qualified technician to restore the product to normal condition.
e
f
If the product has been dropped or the cabinet has been damaged
If the product exhibits a distinct change in performance, indicating a
need for service.
12 Replace the battery with the same type as the product's battery we
recommend. Use of another battery may present a risk of fire or explosion.
Refer battery replacement to a qualified service technician.
13 Warning! Batteries may explode if not handled properly. Do not
disassemble or dispose of them in fire. Keep them away from children and
dispose of used batteries promptly.
14 Use only the proper type of power supply cord set (provided in your
accessories box) for this unit. It should be a detachable type: UL listed/CSA
certified, type SPT-2, rated 7A 125V minimum, VDE approved or its
equivalent. Maximum length is 15 feet (4.6 meters).
Download from Www.Somanuals.com. All Manuals Search And Download.
Notices
FCC notice
Laser compliance statement
Important safety instructions
iii
iii
iv
v
1 System tour
Product briefing
Processor
Memory subsystem
Storage
Graphics interface
Networking
I/O ports
Serial ATA ports
Caring features
Product specification summary
External and internal structure
Front bezel
7
Front panel
Rear panel
Internal components
System boards
8
10
12
14
14
17
Mainboard layout
Hot Plug HDD Cage backplane board layout (SCSI)
Hot Plug HDD Cage backplane board layout (SATA) 18
2 System setup
Setting up the system
25
26
27
28
29
30
31
32
33
Preinstallation requirements
Connecting peripherals
To connect the PS/2 keyboard
To connect the PS/2 mouse
To connect the VGA monitor
To connect the power cable
Turning on the system
Power-on problems
Operating system configuration
Network connection
Tower-to-rack option
Turning off the system
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
Upgrading the system
Installation precautions
56
60
60
62
64
64
66
67
Opening the server
Before opening the server
To open the front bezel
To remove the front bezel
To remove the side panel
Configuring the Hot Plug HDD cage
To remove the Hot Plug HDD cage
To install a hard disk into the carrier
To install the Hot Plug HDD cage
Configuring the non-Hot Plug HDD cage
To remove the cage
To install a hard disk into the cage
To install the cage
Installing and removing storage devices
To remove a 5.25-inch storage device
To install a 5.25-inch storage device
Upgrading the CPU
To remove a CPU with heatsink
Processor Sequence
To install a CPU with heatsink
Upgrading the system memory
To remove a DIMM
To install a DIMM
Replacing the Backup Battery
Installing an expansion card
To install an expansion card
Installing a redundant power supply module
To install a redundant power supply module
4 BIOS setup
BIOS setup
Entering BIOS setup
Main
Advanced
72
74
76
77
78
83
84
85
87
Processor Summary and Configuration
IDE Configuration
Floppy Configuration
Super I/O Configuration
USB Configuration
PCI Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory Configuration
Boot
Boot Settings Configuration
Boot Device Priority
Hard Disk Drives
Removable Devices
ATAPI CD/DVD Devices
Security
To set an Administrator/User password
To remove the User password
Server
110
112
112
113
114
115
117
ꢀꢀꢁ
119
System Management
Serial Console Features
Event Log Configuration
Exit
Upgrading the BIOS
Preparing for the Upgrade
Recording the Current BIOS Settings
Obtaining the Upgrade
Creating a Bootable Diskette
Creating the BIOS Upgrade Diskette
Upgrading the BIOS
Changing the BIOS Language
Recovering the BIOS
Manually Recovering the BIOS
Clearing the CMOS
Clearing the Password
BIOS Error Messages
BIOS POST Beep Codes
BIOS Recovery Beep Codes
Configuration and BIOS Select Jumpers
Resetting the System
123
123
124
125
125
126
126
127
128
Problems following Initial System Installation
First Steps Checklist
Hardware Diagnostic Testing
Verifying Proper Operation of Key System Lights
Confirming Loading of the Operating System
Specific Problems and Corrective Actions
Power Light Does Not Light
No Characters Appear on Screen
Characters Are Distorted or Incorrect
Download from Www.Somanuals.com. All Manuals Search And Download.
System Cooling Fans Do Not Rotate Properly
Diskette Drive Activity Light Does Not Light
Optical Drive Activity Light Does Not Light
Cannot Connect to a Server
Problems with Network
System Boots when Installing PCI Card
129
130
131
Problems with Newly Installed Application Software 131
Problems with Application that Ran Correctly Earlier 132
Hard Drive(s) are not Recognized
Bootable CD-ROM Is Not Detected
LED Information
132
Installing ASM
System requirements
System setup
137
137
Appendix C: Altos G520 Rack Installation Guide139
System rack installation
141
142
143
Vertical mounting hole pattern
Screw types for rack installation
Installing the system into the rack
Appendix D: SATA RAID Configuration
Configuring the onboard SATA RAID
149
149
149
How to enable the onboard SATA RAID function
How to create RAID 1 volume
Loading onboard SATA RAID default setting
Appendix E: RAID Configuration
Configuring the SCSI/SCSI RAID HBA
How to use SCSI HBA setup utility
How to use SCSI RAID HBA setup utility
MegaRAID Configuration Utility
155
155
156
Appendix F: Diagnostic Code Checkpoints 159
POST Code Checkpoints
Bootblock Initialization Code Checkpoints
Bootblock Recovery Code Checkpoint
161
168
171
Index
175
Download from Www.Somanuals.com. All Manuals Search And Download.
The Acer Altos G520 series server is a
powerful dual-processor system loaded with
a host of new and innovative features. The
system offers a new standard for flexible
productivity ideal for general business
applications, email, web service and print
services.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Product briefing
This section provide basic information concerning the configuration of
your Altos G520 system.
Processor
•
•
Single or dual Intel® Xeon™ processor with 800 MHz FSB
Intel® Hyper-Threading™ Technology support
Memory subsystem
•
•
Four (184 - pin) DIMM slots
DDR 333/400 MHz ECC Register, Buffered memory modules
supported
•
Maximum upgrade - 8 GB
Warning! Functionality issues may be encountered if mixed
memory types are installed on the same server board. DIMM
modules of identical type, banking and stacking technology, and
vendor should be installed in the Altos G520.
Caution! When using multiple memory modules it is
recommended that you AVOID using modules from different
manufacturers or that run at different speeds from each other.
Note: 333 MHz memory will run at 320 MHz when used with a
processor with 800 MHz system bus frequency.
Storage
•
•
•
•
5.25 inch IDE CD-ROM drive
3.5 inch Floppy disk drive
Support for three (max) hard disk drives
Four additional 5.25 Inch device bays for add-on options such as:
DDS4 DAT 20/40 GB tape backup drive
•
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
4
•
•
•
DAT72 36/72 GB tape backup drive
AIT1 35/91 GB tape backup drive
DVD-ROM, DVD-RW, DVD-Dual or other optical drive
Graphics interface
•
On-board ATI RageXL PCI Video with 8MB memory
Networking
•
Single Gigabit Ethernet port
I/O ports
•
Front
Two USB 2.0 ports
•
•
Rear
Four USB 2.0 ports
Two PS/2 ports (keyboard/mouse)
One LAN port (RJ-45)
One parallel port
•
•
•
•
•
Two serial ports
Serial ATA ports
•
Two serial ATA ports supporting RAID 0 or RAID 1
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Caring features
Part of Acer’s mission, as a company that cares about its end users, is to
provide features that make operation, maintenance, and upgrading
your system simpler and faster. The Altos G520 is no exception to this
rule. The following features and options are provided.
•
•
•
•
Cost efficient operation in a value oriented package.
Front accessible USB ports.
Acer EasyBUILD for efficient system setup and installation.
Acer Server Manager (ASM) suite of comprehensive management
tools.
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
6
Product specification summary
Highlighted below are the system’s key features:
•
•
Single or dual Intel Xeon processor supporting 800 MHz FSB
Intel E7320 core logic chipset consisting of:
•
•
Intel 827320 Memory Controller Hub (MCH)
Intel 6300ESB I/O Controller Hub (ICH)
•
Intel 82541 Platform LAN Connect (PLC) device for 10/100/1000
Mbits/sec Ethernet LAN
•
•
Dual on-board SATA 150 ports
Five PCI bus slots with three separate bus segments
•
•
•
One PCI-Express X4 bus slot
Two 64-bit/66 MHz PCI-X bus slots
Two 32-bit/33 MHz PCI bus slot
•
•
ATI Rage XL video controller with 8 MB SDRAM
Four DIMM sockets supporting ECC 266/333 MHz DDR modules for
a maximum memory capacity of 8 GB
•
•
Media storage
•
•
3.5-inch, 1.44 MB floppy drive
IDE CD-ROM drive
Additional media storage capacity
•
Hot Plug HDD cage
• supporting up to four 3.5 inch SCSI Ultra320 15K rpm 80pin
drives
• supporting up to four 3.5 inch SATA 150/300 10K rpm drives
Non-Hot Plug HDD cage
•
• supporting up to four 3.5 inch 68pin SCSI drives
• supporting up to four 3.5 inch SATA 150/300 drives
•
•
External ports
• PS/2 keyboard/mouse ports
• One Serial/VGA (monitor) port
• Four USB 2.0 ports
• One LAN port
Power supply unit (PSU)
•
610-watt 1+0/1+1 redundant power supply subsystem (with
power distribution board).
600-watt single standard (non-redundant) power supply.
•
Download from Www.Somanuals.com. All Manuals Search And Download.
7
External and internal structure
Front bezel
Note: One pair of system keys are attached to the rear panel. .
No.
1
Description
No.
2
Description
Front bezel
Security keylock
3
System power indicator
Fault indicator
4
Hard disk activity indicator
LAN1 activity indicator
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
9
No.
1
Description
CD-ROM drive Stop/Eject button
CD-ROM drive activity indicator
CD-ROM drive
2
3
4
Volume control
5
CD-ROM drive Headphone/Earphone port
5.25-inch half-height drive bay
6
7
Hot Plug hard disk cage -or- Non-Hot Plug hard disk cage
(manufacturing optional)
8
HDD carrier (for Hot Plug HDD Cage only)
Floppy drive activity indicator
Floppy drive
9
10
11
12
Floppy drive Eject button
Hot Plug HDD power indicator 1 (for Hot Plug HDD cage only)
Hot Plug HDD access indicator 2 (for Hot Plug HDD cage only)
Power button
13
14
15
16
17
18
System power indicator
Hard disk activity indicator
System fault indicator
LAN activitiy indicator
1 This indicator lights up green to indicate HDD power on and lights up in red when a
HDD fault occurs.
2 This indicator lights up green to indicate drive access.
3 When system is degraded or faulty,the status indicator would blink or light up amber.
.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
No.
1
Icon
Description
Main power supply cable socket
USB ports
2
3
4
PS/2 keyboard port
PS/2 mouse port
5
VGA/monitor port
Serial port
6
7
8
Gigabit LAN port (10/100/1000 Mbps)
9
Expansion slots
Main power supply indicator 1
10
Main power supply fail indicator 2
11
12
13
14
Main standard 600-watt power supply unit (PSU)
Rear system fan
Side Panel lock release
1 This indicator will light up green when the power supply module is functioning properly.
2 This indicator will light up amber when the power supply module or any PSU internal fan
fails.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
No.
Description
Power supply module bays for two redundant PSUs 1 -or-
one single standard PSU bay (Manufacturing optional)
1
2
3
4
5
6
Rear system fan
Rear system fan screw (to secure the rear system fan)
Mainboard
PCI bus slot
Air baffle
1 Though the system supports two hot-swappable power supply modules, the sys-
tem comes bundled with a single standard 600-watt power supply module only.
You have the option to purchase an extra power supply module to provide the sys-
tem with a redundant power source.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Note: Unless otherwise indicated, all mainboard features
indicated on the table below apply to both the Altos G520 and
Altos G520 Basic models.
Item
A
B
Description
64-bit/66 MHz PCI-X bus slot 1
64-bit/66 MHz PCI-X bus slot 2
ATI Rage XL VGA chipset
32-bit/33 MHz PCI bus slot 3
x4 PCI-Express slot 4
C
D
E
F
Gigabit LAN chipset
G
H
I
32-bit/33 MHz PCI bus slot 5
Gigabit LAN port (10/100/1000 Mbps)
VGA/monitor port
J
Serial port
K
Upper: PS/2 mouse port
Lower: PS/2 keyboard port
L
USB ports
M
N
O
P
Auxilliary power connector
Main power connector
Rear system fan headers (two)
DIMM slots
Q
R
+12V CPU power connector
Intel® E7320 MCH chipset
CPU socket 1
S
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
16
Item
Description
US
T
CPU 1 fan header
CPU socket 2
UT
V
CPU 2 fan header
ATA power connector
BIOS select jumper
W
X
IPMB connector
Y
Floppy drive connector
Primary and Secondary ATA connector
Front system fan header
Front panel connector
Front panel USB header
ARMC connector
Z
AA
BB
CC
DD
EE
FF
GG
HH
SATA A1 and A2 connectors
Intel® 6300ESB ICH (ICH5 HR)
Chassis Intrusion header
Jumper Block
1-3 CMOS Clear
5-7 Password Clear
9-11 Recovery Boot
II
Serial B header
SCSI LED connector
Battery
JJ
KK
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Label
Description
2
3
SATA cable connector
HDD backplane power connector (10pin)
Download from Www.Somanuals.com. All Manuals Search And Download.
1 System tour
20
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter gives you instructions on how to set up
the system. Procedures on how to connect
peripherals are also explained.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Setting up the system
Preinstallation requirements
Selecting a site
Before unpacking and installing the system, select a suitable site for
the system for maximum efficiency. Consider the following factors
when choosing a site for the system:
•
•
•
•
•
Near a grounded power outlet
Clean and dust-free
Stable surface free from vibration
Well-ventilated and away from sources of heat
Secluded from electromagnetic fields produced by electrical
devices such as air conditioners, radio and TV transmitters, etc.
Checking the package contents
Check the following items from the package:
•
•
•
•
•
Acer Altos G520 series system
Acer Altos G520 series User’s guide
Acer EasyBUILD
Acer Altos G520 series Accessory box
System keys (attached to the rear panel of the system)
If any of the above items are damaged or missing, contact your dealer
immediately.
Save the boxes and packing materials for future use.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
24
Connecting peripherals
The system unit, keyboard, mouse, and monitor constitute the basic
system. Before connecting any other peripherals, connect these basic
peripherals first to test if the system is running properly.
Note: Unless otherwise indicated, all illustrations shown in this
section show the Altos G520 server chassis.
To connect the PS/2 keyboard
Plug the keyboard cable into the PS/2 keyboard port
port) located on the rear panel of the server.
(purple
Download from Www.Somanuals.com. All Manuals Search And Download.
27
To connect the power cable
Plug the power cable into the power cable socket located on the rear
panel of the server. Then plug the other end of the power cable into a
power outlet. The figure below shows the Altos G520 Basic model.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
28
Turning on the system
After making sure that you have properly set up the system and
connected all the required cables, you can now power on the system.
To power on the system, press the power button on the front panel.
The system starts up and displays a welcome message. After that, a
series of power-on self-test (POST) messages appears. The POST
messages indicate if the system is running well or not.
Note: The illustration below shows the Altos G520 server chassis.
Note: If the system does not turn on or boot after pressing the
power button, go to the next section for the possible causes of the
boot failure.
Aside from the POST messages, you can determine if the system is in
good condition by checking if the following occurred:
•
•
Power indicator on the front panel lights up (green)
Num Lock, Caps Lock, and Scroll Lock indicators on the keyboard
light up
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Power-on problems
If the system does not boot after you have applied power, check the
following factors that might have caused the boot failure.
•
The external power cable may be loosely connected.
Check the power cable connection from the power source to the
power cable socket on the rear panel. Make sure that the cable is
properly connected to the power source and to the power cable
socket.
•
•
No power comes from the grounded power outlet.
Have an electrician check your power outlet.
Loose or improperly connected internal power cables.
Check the internal cable connections. If you are not confident to
perform this step, ask a qualified technician to assist you.
Warning! Make sure all power cords are disconnected from the
electrical outlet before performing this task.
Note: If you have gone through the preceding actions and the
system still fails to boot, ask your dealer or a qualified technician
for assistance.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
30
Operating system configuration
The Acer Altos G520 series server comes with Acer EasyBUILD that
allows you to conveniently install your choice of operating system. To
start using EasyBUILD, follow the steps below.
1
2
Locate the EasyBUILD System CD included in the system package.
With your system powered on, gently press the optical drive Stop/
Eject button.
3
4
When the disc tray slides open, insert the EasyBUILD System CD
with the label or title side of the disc facing upward.
Note: When handling the disc, hold it by the edges to avoid
smudges or fingerprints.
Gently press the disc down to make sure that it is properly
inserted.
Caution! While pressing the disc, be careful not to bend the disc
tray. Make sure that the disc is properly inserted before closing
the disc tray. Improper insertion may damage both the disc and
the optical drive.
5
6
Gently press the drive Stop/Eject button again to close the disc
tray.
The Acer EasyBUILD sequence begins automatically. Follow all
onscreen instructions.
For more information, refer to the EasyBUILD Installation guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Network connection
The server has one 10/100/1000 Mbps Gigabit Etherned LAN port
located on the rear panel for fast network connection.
To connect to the network, simply plug the network cable into the
Gigabit LAN port
(gray port).
Note: The illustration below shows the Altos G520 Basic server
chassis.
Note: Consult the operating system manual for information on
how to configure the network setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
32
Tower-to-rack option
Aside from its tower configuration, the Acer Altos G520 series server
can also be mounted in a rack-model position. A rack mount kit is
available for customers who want to convert a tower-mounted system
to rack-model design. To purchase a rack mount kit, contact your local
Acer representative.
The figure below shows the server in a rack-mount position.
Note: The illustration above shows the Altos G520 server chassis.
Rack Mount instructions are provided as an appendix to this
manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Turning off the system
To turn off the server, on the Windows taskbar click on the Start
button, point to Shut Down..., select Shut down from the
drop-down window then click on OK. You can then turn off all
peripherals connected to your server.
If you are unable to shutdown the server within Windows, press and
hold the power button for at least four seconds to force quit all
applications and shut down.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
34
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter discusses the precautionary
measures and installation procedures you
need to know when upgrading the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Upgrading the system
Certain components of the server are upgradeable such as the drives,
the CPU, the memory, and the expansion cards. However, for safety
purposes, we do not recommend that you perform these upgrades
yourself. If you want to replace or upgrade any of these components,
contact your dealer or a qualified service technician for assistance.
Important: Observe the installation precautions described in the
subsequent section when installing or removing a server
component.
Installation precautions
Before you install any server component, we recommend that you read
the following sections. These sections contain important ESD
precautions along with preinstallation and post-installation
instructions.
ESD precautions
Electrostatic discharge (ESD) can damage the processors, motherboard,
disk drives, expansion boards, or other components. Always observe
the following precautions before you install a server component:
1
Do not remove a component from its protective packaging until
you are ready to install it.
2
Wear a wrist grounding strap and attach it to a metal part of the
server before handling components. If a wrist strap is not
available, maintain contact with the server throughout any
procedure requiring ESD protection.
Preinstallation instructions
Always observe the following before you install any component:
1
2
Turn off the system and all the peripherals connected to it.
Unplug all cables from the power outlets.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
38
3
4
5
Open the system according to the instructions beginning on page
39.
Follow the ESD precautions described in this section when
handling a server component.
Remove any expansion board(s) or peripheral(s) that block access
to the DIMM socket or other component connector.
See the following sections for specific installation instructions on the
component you want to install.
Warning! Failure to properly turn off the server before you start
installing components may cause serious damage. Do not attempt
the procedures described in the following sections unless you are
a qualified service technician.
Post-installation instructions
Observe the following after installing a server component:
1
See to it that all components are installed according to the
described step-by-step instructions.
2
Reinstall any expansion board(s) or peripheral(s) that you have
previously removed.
3
4
5
6
Reinstall the air baffle.
Reinstall the chassis panels.
Connect the necessary cables.
Turn on the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Opening the server
Caution! Before you proceed, make sure that you have turned off
your system and all peripherals connected to it. Read the
“Preinstallation instructions” on page 37.
You need to open the server before you can install additional
components. The front bezel and left side panel are removable to
allow access to the system’s internal components. Refer to the
following sections for instructions.
Before opening the server
Before opening the server, observe the following precautions:
1
2
3
Turn off the system and all the peripherals connected to it.
Unplug all cables from the power outlets.
Place the system unit on a flat, stable surface.
Note: The illustrations used in this section show the Altos G520
server chassis.
To open the front bezel
A security lock secures the front bezel to protect your system unit
against unauthorized access.
To open the front bezel:
1
Insert the key into the lock and turn it clockwise until it points to
the unlocked icon
.
2
Open the front bezel.
To remove the front bezel
The front bezel is attached to the chassis by screwless hinges.
To remove the front bezel:
1
Unlock the bezel with the key (when necessary).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
40
2
3
Open it approximately 90°.
Lift it up a little (1), then move it away from the chassis (2).
4
Remove the upper bezel assembly by pressing the two finger
releases (1), then lift from the bottom (2) and remove.
Download from Www.Somanuals.com. All Manuals Search And Download.
41
To remove the side panel
The side panel is attached to the server by two (non-removeable)
thumbscrews.
To remove the side panel:
1
Loosen the thumbscrews located at the end of the left panel
closest to the rear panel (1).
2
Slide the left panel slightly rearward (2), then upward (3) before
detaching it from the chassis (4).
To remove the air baffle
Remove the air baffle to allow easy access to the motherboard and
system components.
Follow the steps below to remove the air baffle:
1
Remove the two screws (four total) at either end of the air
baffle (1). Save the screws for later use.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
42
2
Pull out the air baffle to remove it from the chassis (2).
Caution! After completing the component upgrade/replacement
procedures, do not forget to reinstall the air baffle before
replacing the chassis panels. Failure to do so will reduce the
system’s cooling efficiency which can adversely affect
performance or cause damage due to overheating.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Configuring the Hot Plug HDD
cage
This section includes instructions for removing and installing the
Hot Plug HDD cage as well as procedures on how to install a hard disk
into the cage’s hard disk carrier.
Note: The Hot Plug HDD cage feature is only applicable to the
Altos G520 model.
To remove the Hot Plug HDD cage
Important: Before detaching the Hot Plug HDD cage from the
chassis, make sure to first remove all hard disks from their carriers.
For instructions, refer to the succeeding section.
1
2
Remove the two parts of the front bezel, the side panel and the air
baffle. Refer to the previous section for detailed intructions.
Disconnect the following cables from the cage (SCSI):
a
b
c
SCSI cable
SCSI HDD 6 pin management cable
SCSI HDD power cable
3
Disconnect the following cables from the cage (SATA):
a
SATA cable
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
44
b
SATS HDD power cable
a
b
4
5
Loosen the four thumbscrews that secure the cage to the chassis
(1).
Pull the cage from the chassis (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
45
To install a hard disk into the carrier
Note: You need not remove the Hot Plut HDD cage from the
chassis to install a hard disk into the cage’s hard disk carrier.
1
Press the HDD release lever (1), then pull the hard disk carrier from
the cage (2).
2
3
Remove the four screws to open the hard disk carrier. Keep the
screws for later use.
When applicable, remove any previously installed hard disk.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
46
4
Install a hard disk in the hard disk carrier then secure it with the
four screws you removed earlier.
5
6
Insert the hard disk carrier into the cage with the lever fully
extended.
Push the lever back until it clicks into place. Make sure that the
drive is properly inserted before closing the lever.
To install the Hot Plug HDD cage
1
2
Detach the chassis panels and remove the air baffle.
Connect the following cables to the backplane board (SCSI):
a
SCSI cable
b
SCSI HDD 6 pin management cable
Download from Www.Somanuals.com. All Manuals Search And Download.
47
c
SCSI HDD power cable
3
Connect the following cables to the backplane board (SATA):
a
SATA cable
b
SATA HDD power cable
a
b
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
48
4
Insert the Hot Plug HDD cage into the housing (1), then tighten
the four thumbscrews to secure it to the chassis (2).
5
6
Attach the other end of these cables to the corresponding
connectors on the mainboard.
Refer to “Mainboard layout” on page 14 for the location of the
connectors.
Reinstall the air baffle and the chassis panels.
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Configuring the non-Hot Plug HDD
cage
This section includes instructions for removing and installing the non-
Hot Plug HDD cage as well as procedures on how to install a hard disk
into the cage.
To remove the cage
1
2
3
4
Turn off the system and all the peripherals connected to it.
Unplug all cables from the power outlets.
Place the system on a flat, stable surface.
Remove the front bezel, inner front panel, side panel, and air
baffle.
5
6
Disconnect the HDD bus cable and the HDD power cable from the
hard disk drive.
Loosen the four thumbscrews that secure the cage to the chassis
(1).
7
Removet the cage from the chassis (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
50
To install a hard disk into the cage
1
Remove the HDD cable cage from the chassis. Refer to the
instructions in the preceding section.
2
Remove the four screws that secure a previously installed hard disk
to the cage then pull the HDD out.
3
Install a new hard disk into the cage then secure it with the four
screws you removed in the previous step.
Note : Make sure the hard disk is tightened by screws on the cage.
4
Reinstall the HDD cable cage to the chassis. Refer to the
instructions in the subsequent section.
Download from Www.Somanuals.com. All Manuals Search And Download.
51
To install the cage
1
2
3
4
5
Turn off the system and all the peripherals connected to it.
Unplug all cables from the power outlets.
Place the system unit on a flat, stable surface.
Remove the front bezel, side panel and air baffle.
Insert the cage into the housing (1), then tighten the four
thumbscrews to secure it to the chassis (2).
6
Connect the HDD bus cable and the power cable to the hard disk
drive.
7
Reinstall the air baffle and the chassis panels.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
52
Installing and removing storage
devices
The system supports one 3.5-inch and three 5.25-inch internal storage
devices. The system comes pre-installed with a floppy drive and a CD-
ROM drive. The two empty 5.25-inch half-height bays allow you to
install additional drives such as another optical drive or a tape drive.
To remove a 5.25-inch storage device
1
Observe the ESD precautions and pre-installation procedures
described on page 37.
2
3
Disconnect the power and bus cables from the old drive.
Press the tool-less locking tabs on each side of the CD-ROM drive
(1) before pulling it from the chassis (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
53
To install a 5.25-inch storage device
Prior to inserting any device into a 5.25 inch device bay, you must
attach mounting rails to it.
Note : Contact you local Acer dealer or authorized service center
to purchase the 5.25 inch device mounting kit.
1
Attach the rails to the 5.25inch device with four screws (included in
the kit).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
54
2
Insert the CD-ROM drive into the drive bay until the locking tabs
click.
3
4
Connect the power and bus cables to the new drive.
Observe the post-installation instructions described on page 38.
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Upgrading the CPU
This section includes instructions for removing and installing a CPU.
To remove a CPU with heatsink
Before installing a new CPU in a socket, remove first any previously
installed CPU from that socket.
Important: Before removing a CPU from the mainboard, make
sure to create a backup file of all important data.
1
Observe the ESD precautions and pre-installation procedures
described on page 37.
2
3
Locate the CPU sockets on the mainboard.
To detach the CPU from its socket, follow the steps below:
Unplug the CPU fan from the mainboard (1).
Using a screwdriver, loosen the screws that hold the heatsink
assembly in place (2).
Remove the heatsink (3).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
56
Lift the CPU locking lever until it is fully extended (1).
Gently unseat and pull the CPU from the socket (2).
Warning! The heatsink becomes very hot when the system is on.
NEVER touch the heatsink with any metal or with your hands.
Processor Sequence
If only one CPU is to be installed, it must be installed in the CPU 1
socket, see “CPU socket 1” in “Mainboard layout” for more
termination module. When installing multiple processors, install CPU 1
first, then CPU 2.
To install a CPU with heatsink
1
Observe the ESD precautions and pre-installation procedures
described on page 37.
2
3
Locate the CPU socket on the mainboard.
Align the CPU to its socket, making sure that pin 1 (indicated by
the notched corner) of the CPU connects to hole 1 of the socket
(on the bottom right corner).
Download from Www.Somanuals.com. All Manuals Search And Download.
57
4
To install the CPU to its socket, follow the steps below:
Insert the CPU into the socket (1).
Lower the CPU locking lever to secure the CPU (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
58
5
Replace the heatsink on top of the CPU (1).
Using a screwdriver, loosen the screws that hold the heatsink
assembly in place (2).
Plug the CPU fan in to the mainboard (3).
For help locating the CPU fan connectors on the mainboard, see
“Mainboard layout” on page 14.
6
Observe the post-installation instructions described on page 38.
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Upgrading the system memory
This section includes instructions for removing and installing a
memory module.
The Server Boards Altos G520 each provides four DDR266 / DDR333
DIMM sites in two DIMM banks. The maximum memory capacity is 8GB
for either DDR266 or DDR333 memory. Memory DIMM technologies
supported are: 128MB, 256MB, 512MB, 1 GB and 2 GB.
The minimum memory configuration is one DIMM, installed in DIMM
socket 1B (the socket farthest from the processors). However, for
optimum performance and dual-channel interleave operation, a
minimum of two DIMMs should be installed. DIMMs on channel A are
paired with DIMMs on channel B to configure 2-way interleaving.
Both DIMMS in Bank 1 (DIMM1B and DIMM1A) must be populated
before any DIMMs are installed in Bank 2 (DIMM2B and DIMM2A).
Bank 2 must be populated in pairs.
Both DIMMs in a bank must be identical (same manufacturer, CAS
latency, number of rows, columns and devices, timing parameters etc.).
Although DIMMs within a bank must be identical, the BIOS supports
various DIMM sizes and configurations allowing the banks of memory
to be different.
Note: Dual-channel memory requires symmetrical memory
modules using the same density (e.g. 256MB,512MB), bus width
(e.g. x8 ,x16) and granule technology (e.g. 256M-bit, 512M-bit)
The mixing of DDR266 and DDR333 memory is supported on the Server
Boards Altos G520. However, when mixing DIMM types, DDR333 will
be treated as DDR266.
Warning! Functionality issues may be encountered if mixed
memory types are installed on the same server board. DIMM
modules of identical type, banking and stacking technology, and
vendor should be installed in the Altos G520.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
60
To remove a DIMM
Before installing a new DIMM in a socket, remove first any previously
installed DIMM from that socket.
Important: Before removing any DIMM from the mainboard,
make sure to create a backup file of all important data.
1
Observe the ESD precautions and pre-installation procedures
described on page 37.
2
3
Locate the DIMM slots on the mainboard.
Press the holding clips on both sides of the socket outward to
release the DIMM (1).
4
Gently pull the DIMM upward to remove it from the socket (2).
Note: Place your forefingers on the top of the DIMM before
pressing the holding clips to gently disengage the DIMM from the
socket.
To install a DIMM
1
Observe the ESD precautions and pre-installation procedures
described on page 37.
2
3
Locate the DIMM slots on the mainboard.
Open the clips on the socket.
Download from Www.Somanuals.com. All Manuals Search And Download.
61
4
5
Align then insert the DIMM into the socket (1).
Press the holding clips inward to lock the DIMM in place (2).
Note: The DIMM socket is slotted to ensure proper installation.
If you insert a DIMM but it does not fit easily into the socket, you
may have inserted it incorrectly. Reverse the orientation of the
DIMM and insert it again.
6
Observe the post-installation instructions described on page 38.
Reconfiguring the system memory
The system automatically detects the amount of memory installed.
Run the BIOS setup to view the new value for total system memory and
make a note of it.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
62
Replacing the Backup Battery
The lithium battery on the server board powers the RTC for up to 10
years in the absence of power. When the battery starts to weaken, it
loses voltage, and the server settings stored in CMOS RAM in the RTC
(for example, the date and time) may be wrong. Contact your customer
service representative or dealer for a list of approved devices.
1
2
3
Observe the safety and ESD precautions above and at the
beginning of this book.
Turn off all peripheral devices connected to the server. Turn off
the server.
Remove power from your system by unplugging the AC power
cord.
4
5
6
7
Remove the chassis cover.
Locate the battery.
Gently pull back on the metal tab to release the battery.
Remove the battery from its socket. See “Battery” in “Mainboard
layout”
8
Dispose of the battery according to local ordinance.
Download from Www.Somanuals.com. All Manuals Search And Download.
63
9
Remove the new lithium battery from its package, and, being
careful to observe the correct polarity, insert it in the battery
socket.
10 Reconnect or replace any internal components you needed to
disconnect or remove.
11 Replace the server’s cover. Reconnect any external components
you needed to disconnect.
12 Attach the AC power cord.
13 Run Setup to restore the configuration settings to the RTC.
WARNING! Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the equipment manufacturer. Discard used batteries according to
manufacturer’s instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
64
Installing an expansion card
This section explains how to install an expansion card. The onboard
expansion slots support PCI (Peripheral Component Interconnect)
cards.
Note : The BIOS setup automatically detects and assigns resources
to the new device (applicable only to Plug-and-Play expansion
cards).
To install an expansion card
Note: The illustrations used in this section show the Altos G520
server chassis.
1
Observe the ESD precautions and pre-installation procedures
described on page 37.
2
3
Locate an empty expansion slot on the mainboard.
With your finger, open the expansion card slot lock on the rear
panel (1).
4
Pull out the card bracket (2).
5
Remove the expansion card from its protective packaging.
Download from Www.Somanuals.com. All Manuals Search And Download.
65
6
7
Align the card in an empty slot on the mainboard.
Insert the bracket with the card into the selected slot (1). Make
sure that the card is properly seated.
8
Secure the card by moving the expansion card locking lever back
to the locked position (2).
9
Observe the post-installation instructions described on page 38.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
66
Installing a redundant power
supply module
The Altos G520 server power subsystem consists of two hot-swappable
power supply module bays that accept standard 610-watt power
supply modules. The system comes bundled with only a single power
supply module leaving one power supply module bay empty. You have
the option to purchase an extra power supply module to provide your
system with redundant power source. This power configuration
enables a fully-configured system to continue running even if one
power supply module fails.
Note: The redundant power source feature is only applicable to
the Altos G520 model.
WARNING! To reduce the risk of personal injury or
damage to the equipment, the installation of power
supply modules should be referred to individuals who are
qualified to service server systems and are trained to deal
with equipment capable of generating hazardous energy
levels.
WARNING! To reduce the risk of personal injury from
hot surfaces, observe the thermal labels on each power
supply module. You can also consider wearing protective
gloves.
WARNING! To reduce the risk of personal injury from
electric shock hazards, do not open the power supply
modules. There are no serviceable parts inside the
module.
Caution! Electrostatic discharge can damage electronic
components. Make sure that you are properly grounded
before handling a power supply module.
Download from Www.Somanuals.com. All Manuals Search And Download.
67
To install a redundant power supply module
1
Remove the screw securing the cover of the empty optional power
supply module bay, then remove the cover.
2
Slide the redundant power supply module into the empty bay until
you feel resistance.
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Upgrading the system
68
3
Press the module handle to secure the power supply module to the
bay.
4
Verify that the power indicators on both the main power supply
and on the newly installed redundant power supply are
illuminated (green).
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter gives information about the
system BIOS and discusses how to configure
the system by changing the settings of the
BIOS parameters.
Download from Www.Somanuals.com. All Manuals Search And Download.
71
BIOS setup
BIOS setup is a hardware configuration program built into your
system's Basic Input/Output System (BIOS). Since most systems are
already properly configured and optimized, there is no need to run this
utility. You will need to run this utility under the following conditions:
•
•
When changing the system configuration
When a configuration error is detected by the system and you are
prompted ("Run Setup" message) to make changes to the BIOS
setup
Note: If you repeatedly receive Run Setup messages, the battery
may be bad. In this case, the system cannot retain configuration
values in CMOS. Ask a qualified technician for assistance.
•
•
•
When redefining the communication ports to prevent any conflicts
When making changes to the Power Management configuration
When changing the password or making other changes to the
security setup
BIOS setup loads the configuration values in a battery-backed
nonvolatile memory called CMOS RAM. This memory area is not part
of the system RAM which allows configuration data to be retained
when power is turned off.
Before you run BIOS setup, make sure that you have saved all open
files. The system reboots immediately after you close the setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
72
Entering BIOS setup
Power on the server to start the system POST (Power On Self Test)
process. During bootup, press <F2> to enter the BIOS setup screen.
Note: Note: You must press <F2> while the system is booting.
This hot key does not work at any other time.
There are several tabs on the setup screen corresponding to the six
major BIOS menus:
•
•
•
•
•
•
Main
Advanced
Boot
Security
Server
Exit
The parameters on the screens shown in this User’s guide display
default system values. These values may not be the same as those in
your system.
Note the following reminders when moving around the setup screen:
•
Use the Left and Right arrow keys to move to the next page or to
return to the previous screen.
•
•
Use the Up and Down arrow keys to select an item.
Use the + and - keys to select an option.
Note: You can configure a parameter that is enclosed in square
brackets. Grayed-out items have fixed settings and are not
user-configurable.
•
•
Use the Tab key to select a field.
Use the Enter key to display a submenu screen.
Note: When a parameter is preceded by a (>), it means that a
submenu screen is available.
Download from Www.Somanuals.com. All Manuals Search And Download.
73
•
•
•
Press F1 for General Help on using the BIOS setup.
Press F10 to save changes and close the BIOS setup.
Press Esc to close the BIOS setup.
In the descriptive table following each of the screen illustrations,
settings in boldface are the default and suggested parameter settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
74
Main
The Main menu displays basic and important information about the
system. These information is necessary for troubleshooting and may
be required when asking for technical support.
The last two parameters on the screen lets you define the system’s time
and date settings. The real-time clock keeps the system date and time.
After setting the date and time, you do not need to enter them every
time you turn on the system. As long as the internal battery remains
good and connected, the clock continues to keep the date and time
accurately even when the power is off.
Parameter
Description
AMIBIOS Version
Build Date
BIOS ID string (excluding build date)
Date when the BIOS setup was created
Download from Www.Somanuals.com. All Manuals Search And Download.
75
Parameter
Description
Processor Type
Speed
Processor brand ID string
Calculated processor speed
Number of processors detected
Amount of physical memory detected
Count
System Memory Size
System Time
Configures the system time in 24hour format
HH:MM:SS
System Date
Language
Configures the system date.
Default value is Build Date
Select the language used by BIOS. Choose from:
•
•
•
•
•
English (default)
French
German
Italian
Spanish
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
76
Advanced
The Advanced menu contains parameter values that define how the
system behaves on startup.
Warning! Be cautious in setting parameter values in the
Advanced menu as any incorrect value may cause the system to
malfunction.
Press Enter to enter the submenu screen of the parameters shown in
the screen below.
Download from Www.Somanuals.com. All Manuals Search And Download.
77
Processor Summary and Configuration
The Processor Summary/Configuration submenu displays general
information about the installed processor(s) and lets you define
advanced settings.
Parameter
Description
Options
Max CPUID
Value Limit
Enable to boot legacy operating systems
Disabled
Enabled
HyperThread-
ing Technology
Controls HyperThreading state. Used to
support older operating systems that do
not support HyperThreading.
Disabled
Enabled
Disable for maximum CPU speed. Enable
to reduce CPU power consumption.
Auto
Intel Speed
Step Tech
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
78
IDE Configuration
The IDE Configuration submenu lets you define the parameter settings
related to the hard disk/s.
Parameter
Description
Option
Onboard
P-ATA
Channels
Controls state of integrated P-ATA
controller.
Disabled
Primary
Secondary
Both
Onboard
S-ATA
Channels
Controls state of integrated S-ATA
controller.
Disabled
Enabled
Configure
S-ATA
as RAID
When enabled the S-ATA channels
are reserved to be used as RAID.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
79
Parameter
Description
Option
A1-3rdM / A2-4th
A1-4thM / A2-3rd
M
M
S-ATA Ports
Definition
Defines priority between S-ATA
channels.
Mixed P-ATA /
S-ATA
Lets you remove a P-ATA and
replace it by S-ATA in a given
channel. only one channel can be
S-ATA.
N/A
Primary IDE
Master
Selects submenu with additional
device deatils.
N/A
N/A
N/A
N/A
N/A
N/A
Primary IDE
Slave
Selects submenu with additional
device deatils.
Secondary IDE
Master
Selects submenu with additional
device deatils.
Secodary IDE
Slave
Selects submenu with additional
device deatils.
Third IDE
Master
Selects submenu with additional
device deatils.
Fourth IDE
Master
Selects submenu with additional
device deatils.
Hard Disk
Write Protect
Used to prevent unauthorized
writes to hard drives.
Disabled
Enabled
IDE Detect
Time Out (sec)
Used with older IDE drives with
longer spin up times.
0
5
10
15
20
25
30
35
ATA(PI) 80Pin
Cable
Detection
80 pin cable is required for
UDMA-66 and above. BIOS detects
the cable by querying the host
and/or device.
Host & Device
Host
Device
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
80
Primary/Secondary/Third/Fourth IDE Master/Slave
These items let you select the IDE hard disk parameters that the system
supports.
Parameter
Device
Vendor
Size
Description
Option
Type of IDE device
Vendor of the selected IDE device
Size of the IDE disk
Driver type
Type
Not Installed
Auto
CD-ROM
ARMD
Download from Www.Somanuals.com. All Manuals Search And Download.
81
Parameter
Description
Option
LBA/Large
Mode
Selects the hard disk drive translation
method. For drivers with more than 504
MB, the LBA mode is necessary.
Disabled
Auto
Block (Multi-
Sector Trans-
fer) Mode
Enhances disk performance depending on
the hard disk in use.
Disabled
Auto
If you set this parameter to Auto, BIOS
setup automatically detects if the
installed hard disk drive supports the
Block Mode function. If supported, it
allows data transfer in blocks (multiple
sectors) at a rate of 256 bytes per cycle.
If you set this parameter to Disabled, data
transfer from and to the device occurs
one sector at a time.
PIO Mode
When set to Auto, BIOS setup
Auto
automatically detects if the installed hard
disk supports the function. If supported,
it allows for faster data recovery and
read/write timing that reduces hard disk
activity time. This results in better hard
disk performance.
0
1
2
3
4
DMA Mode
Selects DMA (Direct Memory Access)
mode. Options include:
Auto
SWDMA0-0
SWDMA0-1
SWDMA0-2
Auto: Auto detected
SWDMAn: SingleWordDMAn
MWDMAn: MultiWordDMAn
UDMAn: UltraDMAn
MWDMA0-0
MWDMA0-1
MWDMA0-2
UWDMA0-0
UWDMA0-1
UWDMA0-2
UWDMA0-3
UWDMA0-4
UWDMA0-5
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
82
Parameter
Description
Option
S.M.A.R.T
Enables or disables the S.M.A.R.T (Self-
Monitoring, Analysis and Reporting
Technology) function of the internal hard
disk.
Auto
Disabled
Enabled
If 'Auto' is selected, BIOS setup will ena-
ble the S.M.A.R.T function if the driver
supports it.
32-bit Data
Transfer
Enables or disables the 32-bit data
transfer function
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Floppy Configuration
The Floppy Configuration submenu displays the type of floppy drive
installed in the server.
Parameter
Description
Option
Floppy Drive A
Floppy disk drive type
None
720 KB, 3.5-inch
1.44 MB, 3.5-inch
2.88 MB, 3-5-inch
Onboard
Flopppy
Controller
Allows BIOS to enable or disable
the floppy controller.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
84
Super I/O Configuration
The PCI/PnP Configuration submenu lets you specify the settings for
the PCI devices.
Parameter
Description
Option
Serial Port A
Address
Option that is used by other serial port is
hidden to prevent conflicting settings.
Disabled
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Serial Port B
Address
Option that is used by other serial port is
hidden to prevent conflicting settings.
Disabled
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Download from Www.Somanuals.com. All Manuals Search And Download.
85
USB Configuration
The USB Configuration submenu lets you specify the settings for the
legacy devices and USB 2.0.
Parameter
Description
Option
USB Function
When set to disabled other USB options
are grayed out.
Disabled
Enabled
Legacy USB
Support
Enables legacy USB support.
Disabled
Keyboard
only
Auto
Keyboard
and
Mouse
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
86
Parameter
Description
Option
Port 60/64
Emulation
Should be enabled for full USB legacy
support.
Disabled
Enabled
USB 2.0
Controller
Enables USB 2.0
Disabled
Enabled
USB 2.0
Controller
Mode
Set transfer rate at 480Mbps (Hi) or
12Mbps (full)
FullSpeed
HiSpeed
Download from Www.Somanuals.com. All Manuals Search And Download.
87
PCI Configuration
The PCI/PnP Configuration submenu lets you specify the settings for
the PCI devices.
Parameter
Description
Option
Onboard Video
Enables or disables VGA controller.
Disabled
Enabled
Dual Monitor
Video
Grayed out if onboard video is set to disa-
bled.
Disabled
Enabled
Onboard NIC 1
(Left)
Enables or disables onboard Network
Interface Controller.
Disabled
Enabled
Onboard NIC 1
ROM
Grayed out if device is disabled.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
88
Memory Configuration
The Memory Configuration submenu provides information about the
DIMMs detected by BIOS. The DIMM number is printed on the
mainboard, see page 14 for help locating them.
Parameter
Description
Option
DIMM 1A
DIMM 1B
DIMM 2A
DIMM 2B
Non-User configurable informational dis-
play.
Installed
Not Installed
Disabled
Spare
Extended
Memory Test
Settings for testing extended memory.
1 MB
1 KB
Every
Location
Disabled
Download from Www.Somanuals.com. All Manuals Search And Download.
89
Parameter
Description
Option
Memory
Retest
When enabled, BIOS will activate and
retest all DIMMs on next boot. Automati-
cally reset to disabled.
Disabled
Enabled
Memory
Remap
Feature
Enable or disable remapping of over-
lapped PCI memory above physical mem-
ory.
Disabled
Enabled
Memory
Sparing
Grayed out if current memory configura-
tion does not support sparing.
Disabled
Spare
Download from Www.Somanuals.com. All Manuals Search And Download.
91
Boot Settings Configuration
The Boot Settings Configuration submenu lets you specify the
preferred settings for system bootup.
Parameter
Description
Option
Quick Boot
Allows the system to boot faster by
skipping some POST routines.
Disabled
Enabled
Quiet Boot
Enables or disables the Quiet Boot func-
tion. When set to Enabled, BIOS setup is in
graphical mode and displays only an iden-
tification logo during POST and while
booting. After booting, the screen displays
the operating system prompt (such as DOS)
or logo (such as Windows). If any error
occurs while booting, the system
Disabled
Enabled
automatically switches to text mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
92
Parameter
Description
Option
Bootup
Num-Lock
Sets the power on state for Numlock.
Off
On
PS/2 Mouse
Support
Enable this parameter if you intend to use
a mouse or trackball with a PS/2 interface.
Disabled
Enabled
Auto
POST Error
pause
When this item is enabled you will be
prompted when an error is detected dur-
ing boot up. If disabled, the system will
boot with no intervention, if possible.
Disabled
Enabled
Hit ‘F2’ Message
Display
Displays “Press ‘F2’ to run Setup” during
POST.
Disabled
Enabled
Scan User Flash
Area
Allows BIOS to scan Flash ROM for user
binaries.
Disabled
Enabled
Boot Device Priority
The Boot Device Priority submenu lets you specify the boot search
sequence during the POST process.
Download from Www.Somanuals.com. All Manuals Search And Download.
93
BIOS setup will display an error message if the drive(s) specified is not
bootable.
Parameter
Description
1st Boot Device
Sets the device from which the system will first
attempt to boot up.
2nd thru 5th
Boot Device
Sets the device from which the system will attempt to
boot up when previoius attempts fail.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
94
Hard Disk Drives
The Hard Disk Drives submenu lets you specify the devices that will be
considered as the primary and secondary hard drives.
Parameter
Description
1st Drive
Sets the device to be considered the primary hard
drive.
2nd Drive
Sets the device to be considered the secondary hard
drive.
Download from Www.Somanuals.com. All Manuals Search And Download.
97
Security
The Security menu allows you to safeguard and protect the system
from unauthorized use by setting up access passwords.
Parameter
Description
Option
Administrator
Password
Prevents unauthorized access to the
BIOS setup
Not Installed
Installed
User Password
Secures your system against unau-
thorized use. Once you set this pass-
word, you have to type it whenever
you boot the system. User password
is available only when a Supervisor
password is set.
Not Installed
Installed
Set Admin
Password
Press Enter to change the Admin pass-
word.
N/A
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
98
Parameter
Description
Option
Set User
Password
Press Enter to change the User pass-
word.
N/A
User Access
Leves
Grayed out unless Admin password is
set.
No Access
View Only
Limited
Full Access
Clear User
Password
Grayed out unless Admin password is
set. Press Enter to clear the user pass-
word.
N/A
Fixed disk
boot sector
protect
Enable or disable boot sector virus
protection.
Disabled
Enabled
Password on
Boot
Grayed out if User password is not
installed.
Disabled
Enabled
Secure Mode
Timer
Grayed out if User password is not
installed.
1 minute
2 minutes
5 minutes
10 minutes
20 minutes
60 minutes
120 minutes
Secure Mode
HotKey (CTRL-
ALT-)
Grayed out if User password is not
installed.
L
Z
Secure Mode
Boot
Grayed out if User password is not
installed.
Disabled
Enabled
Front Panel
Switch Inhibit
Grayed out if a password is not
installed or if AC policy is set to Stays
Off.
Disabled
Enabled
NMI Control
Enable or disable NMI control.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
99
To set an Administrator/User password
1
2
3
Use the up/down keys to highlight a password parameter
(Administrator Password or User Password) then press Enter.
A password box will appear.
Type a password then press Enter.
The password may consist of up to six alphanumeric characters
(A-Z, a-z, 0-9).
Retype the password to verify the first entry then press Enter
again.
After setting the password, the system automatically sets the
chosen password parameter to Installed.
To remove the User password
1
Use the up/down keys to highlight the Clear User Password
parameter then press Enter.
2
3
Enter the current Admin password then press Enter.
Press Enter twice without entering anything in the new and
confirm password fields.
After doing this, the system automatically sets the User password
parameter to Not Installed.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
100
Server
The Server menu allows you to configure the system parameters .
Parameter
Description
Option
System
Management
Press Enter to enter the submenu screen.
N/A
Serial Console
Features
Press Enter to enter the submenu screen.
Press Enter to enter the submenu screen.
N/A
N/A
Event Log
configuration
Assert NMI on
SERR
If enabled, NMI generated on SERR and
logged.
Disabled
Enabled
Assert NMI on
PERR
Grayed out in NMI on SERR is disabled.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
101
Parameter
Description
Option
Resume on AC
Power Loss
When set to Stays Off, Front Panel Switch
Inhibit (in BIOS Security menu) is disabled.
Stays Off
Power On
FRB-2 Policy
Controls action if boot processor is disa-
bled or not.
Retry on
Next Boot
Disable
FRB2 Timer
Late POST
Timeout
Controls time limit for add-in card detec-
tion.
Disabled
5 minutes
10 minutes
15 minutes
20 minutes
Hard Disk OS
Boot Timeout
Controls the time limit for booting an OS
from a HDD.
Disabled
5 minutes
10 minutes
15 minutes
20 minutes
PXE OS Boot
Timeout
Controls the time limit for booting an OS
using PXE boot.
Disabled
5 minutes
10 minutes
15 minutes
20 minutes
OS Watchdog
Timer Policy
Controls the policy upon timeout.
Stay On
Reset
Power Off
Platform Event
Filtering
Enable or disable trigger for system sensor
events.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
103
Serial Console Features
The Serial Console Features submenu allows you to configure serial
port settings.
Parameter
Description
Option
BIOS
Redirection
Port
If enabled, BIOS uses the specified serial
port to redirect the console to a remote
terminal.
Disabled
Serial A
Serial B
Baud Rate
Sets the transfer speed for console redi-
rection.
9600
19.2 K
38.4 K
57. 6 K
115.2 K
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
104
Parameter
Description
Option
Flow Control
If enabled, the system uses the flow con-
trol selected.
No Flow
Control
CTS/RTS
XON/XOFF
CTS/RTS+CD
Terminal Type
PC-ANSI
VT100+
VT-UTF8
ACPI Redirec-
tion port
Enable or disable ACPI OS Headless Con-
sole Redirection.
Disabled
Serial A
Serial B
Download from Www.Somanuals.com. All Manuals Search And Download.
105
Event Log Configuration
The Event log configuration submenu allows you to configured the
event log setting.
Parameter
Description
Option
Clear All Event
Logs
Enable to clear logs.
Disabled
Enabled
BIOS Event
Logging
Allows logging of BIOS events.
Disabled
Enabled
Critical Event
Logging
Logs fatal errors including PERR, SERR,
and ECC.
Disabled
Enabled
ECC Event
Logging
Enable or disable ECC event logging.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
106
Parameter
Description
Option
PCI Error
Logging
Enable or disable PCI error logging.
Disabled
Enabled
FSB Error
Logging
Enable or disable Front-Side Bus log-
ging.
Disabled
Enabled
Hublink Error
Logging
Enable or disable Hublink error logging.
Disabled
Enabled
Download from Www.Somanuals.com. All Manuals Search And Download.
107
Exit
The Exit menu displays the various options to quit from the BIOS setup.
Highlight any of the exit options then press Enter.
Parameter
Description
Save Changes
and Exit
Saves changes made and close the BIOS setup.
Pressing F10 can also be used.
Discard
Changes and
Exit
Exit system setup without saving changes.
Pressing Esc can also be used.
Discard
Changes
Discard any changes made to setup without exiting.
Pressing F7 can also be used.
Load Setup
Defaults
Loads the original BIOS setup parameters.
Pressing F9 can also be used.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
108
Parameter
Description
Load Custom
Defaults
Loads the custom settings for all BIOS parameters as
saved by user.
Save Custom
Defaults
Saves custom settings for all BIOS parameters.
Download from Www.Somanuals.com. All Manuals Search And Download.
109
Upgrading the BIOS
The upgrade utility allows you to upgrade the BIOS in flash memory.
The code and data in the upgrade file include the following:
•
On-board BIOS, ATA-100 RAID BIOS, and PXE option ROMs for the
devices that are embedded on the system board
•
•
The Setup Utility
The System BIOS
Preparing for the Upgrade
The steps below explain how to prepare to upgrade the BIOS,
including how to:
•
•
•
Record the current BIOS settings
Obtain the upgrade utility
Prepare a bootable diskette for the utility
In the unlikely event that a BIOS error occurs during the BIOS update
process, see "Recovering the BIOS" for instructions on performing a
BIOS recovery.
Recording the Current BIOS Settings
1
Boot the computer and press <F2> when you see the message:
Press <F2> Key if you want to run SETUP
2
Write down the current settings in the BIOS Setup program.
Note: Do not skip step 2. You will need these settings to
configure your computer at the end of the procedure.
Obtaining the Upgrade
Download the BIOS image file to a temporary folder on your hard
drive.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
110
Note: Review the instructions distributed with the upgrade
utility before attempting a BIOS upgrade. Review also any release
notes in the release notes file that accompanies the new version
of the BIOS. The release notes may contain critical information
regarding jumper settings, specific fixes, or other information to
complete the upgrade.
Creating a Bootable Diskette
Use a DOS system to create the diskette as follows:
1
2
Insert a diskette in diskette drive A.
At the C:\ prompt, for an unformatted diskette, type:
format a:/s
3
4
or, for a diskette that is already formatted, type:
sys a:
Press <Enter>.
Creating the BIOS Upgrade Diskette
The BIOS upgrade file is a compressed self-extracting archive that
contains the files you need to upgrade the BIOS.
1
2
Insert the bootable diskette into the diskette drive.
While in the directory into which you downloaded the upgrade
file(s), type [filename] a: where “[filename]” is the name of the file
that you downloaded. This command extracts the update files and
places them onto the bootable diskette
Upgrading the BIOS
1
Place the bootable diskette containing the BIOS update files into
the diskette drive of your system. Boot the system with the
diskette in the drive.
2
A menu will appear with two options. Use option 1 to
automatically update the system BIOS.
Use option 2 to manually update the system BIOS and the User
Binary.
Download from Www.Somanuals.com. All Manuals Search And Download.
111
3
4
If you selected option 1, to automatically update the system BIOS:
The system will execute the AfuDOS update utility to update the
BIOS. When the update is complete, the utility will display a green
box with a message that says “Completed Successfully.” The
system will then reboot.
4.If you selected option 2, to manually update the BIOS or to
update the flash memory, you can either select “Update Flash
Memory From a File” or “Update System BIOS”:
•
Update Flash Memory From a File: When prompted for a file
name, type BIOS.wph and press Enter.
•
Update System BIOS: The system will warn you that the BIOS
will be updated. Verify the BIOS version is correct and press
Enter to continue. When the update is complete, the utility
will display a green box with a message that says “Completed
Successfully.” The system will then reboot.
5
6
Wait while the BIOS files are updated. Do not power down the
system during the BIOS update process! The system will reset
automatically when the BIOS update process is completed. Remove
the diskette from the diskette drive.
Check to make sure the BIOS version displayed during POST is the
new version as the system reboots.
7
8
Enter Setup by pressing the F2 key during boot.
In Setup, press the F9 and <Enter> to set the parameters back to
default values.
9
Re-enter the values you wrote down at the beginning of this
process. Press F10 and <Enter> to exit BIOS Setup and Save
Changes.
10 If you do not set the CMOS values back to defaults using the F9
key, the system may function erratically.
Note: You may encounter a CMOS Checksum error or other
problem after reboot. If this happens, shut down the system and
boot it again. CMOS checksum errors require that you enter Setup,
check your settings, save your settings, and exit Setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
112
Changing the BIOS Language
You can use the BIOS upgrade utility to change the language the BIOS
uses for messages and the Setup program. Use a bootable diskette
containing the Acer flash utility and language files.
1
Boot the computer with the bootable diskette in drive A. The BIOS
upgrade utility screen appears.
2
3
4
Select Update Flash Memory From a File.
Select Update Language Set. Press <Enter>.
Select drive A and use the arrow keys to select the correct .lng file.
Press <Enter>.
5
When the utility asks for confirmation that you want to flash the
new language into memory, select continue with Programming.
Press <Enter>.
6
7
When the utility displays the message upgrade is complete,
remove the diskette. Press <Enter>.
The computer will reboot and the changes will take effect.
Recovering the BIOS
In the rare event that the BIOS becomes damaged, a recovery process
needs to be followed to return the system to service. Two methods are
available to recover the BIOS: automatically with the crisis recovery
diskette, and manually by moving a jumper on the system board. These
methods are described below.
Note: BIOS recovery is the mode of last resort, used only when
the main system BIOS will not come up.
Manually Recovering the BIOS
A BIOS recovery can be manually initiated. This option would be used
only when the BIOS is corrupt, but the ROM checksum error does not
occur during POST. To manually initiate a BIOS recovery, use the
following steps:
1
Power down and uplug the system from the AC power source.
Download from Www.Somanuals.com. All Manuals Search And Download.
113
2
3
Move the recovery jumper at J1D1 from pins 13 and 14 to cover
pins 14 and 15.
Insert a bootable diskette containing the file AMIBOOT.ROM into
the A: diskette drive.
4
5
Plug the system into the AC power source and power it on.
A blue screen will be displayed and the recovery process will
automatically run. The system will continue to beep throughout
the recovery process. The recovery process is complete when the
beeping stops.
6
7
8
Remove the diskette.
Power down and unplug the system from the AC power source.
Move the BIOS recovery jumper at J1D1 back to the original
position, covering pins 13 and 14.
9
Plug the system into the AC power source and power it up to
confirm that the recovery was successful.
Clearing the CMOS
If you are not able to access the BIOS setup screens, the CMOS Clear
jumper will need to be used to reset the configuration RAM. The
CMOS Clear jumper is located on jumper block J17.
1
2
3
Power down the system and disconnect the AC power.
Open the server.
Move the jumper from pins 1 and 2 to the Clear CMOS position,
covering pins 2 and 3.
4
5
Reconnect the AC power, power up the system.
When the system begins beeping, power it down and disconnect
the AC power.
6
7
Return the CMOS Clear jumper to the original location, covering
pins 1 and 2.
Close the server chassis, reconnect the AC power and power up the
system.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
114
Clearing the Password
If the user or administrator password(s) is lost or forgotten, moving the
password clear jumper into the “clear” position clears both passwords.
The password clear jumper must be restored to its original position
before a new password(s) can be set. The password clear jumper is
located on jumper block J17.
1
2
3
Power down the system and disconnect the AC power.
Open the server chassis.
Move the jumper from pins 5 and 6 to the Clear Password position,
covering pins 6 and 7.
4
5
6
Reconnect the AC power, power up the system.
Power down the system and disconnect the AC power.
Return the Password Clear jumper to the original location,
covering pins 5 and 6.
7
Close the server chassis.
Download from Www.Somanuals.com. All Manuals Search And Download.
115
BIOS Error Messages
When a recoverable error occurs during the POST, the BIOS displays an
error message describing the problem.
Error Message
GA20 Error
Explanation
An error occurred with Gate A20 when switching to
protected mode during the memory test.
Pri Master HDD Error
Pri Slave HDD Error
Sec Master HDD Error
Sec Slave HDD Error
Could not read sector from corresponding drive.
Pri Master Drive -
ATAPI Incompatible
Pri Slave Drive -
Corresponding drive is not an ATAPI device. Run
Setup to make sure device is selected correctly.
ATAPI Incompatible
Sec Master Drive -
ATAPI Incompatible
Sec Slave Drive -
ATAPI Incompatible
A: Drive Error
No response from diskette drive.
CMOS Battery Low
The battery may be losing power. Replace the bat-
tery soon.
CMOS Display Type
Wrong
The display type is different than what has been
stored in CMOS. Check Setup to make sure type is
correct.
CMOS Checksum Bad
The CMOS checksum is incorrect. CMOS memory
may have been corrupted. Run Setup to reset val-
ues.
CMOS Settings
Wrong
CMOS values are not the same as the last boot.
These values have either been corrupted or the bat-
tery has failed.
CMOS Date/Time Not
Set
The time and/or date values stored in CMOS are
invalid. Run Setup to set correct values.
DMA Error
Error during read/write test of DMA controller.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
116
Error Message
Explanation
FDC Failure
Error occurred trying to access diskette drive con-
troller.
HDC Failure
Error occurred trying to access hard disk controller.
NVRAM is being checked to see if it is valid.
NVRAM was invalid and has been updated.
NVRAM was invalid but was unable to be updated.
Checking NVRAM.....
Update OK!
Updated Failed
Keyboard Error
Error in the keyboard connection. Make sure key-
board is connected properly.
KB/Interface Error
Keyboard interface test failed.
Memory Size
Decreased
Memory size has decreased since the last boot. If no
memory was removed, then memory may be bad.
Memory Size
Increased
Memory size has increased since the last boot. If no
memory was added, there may be a problem with
the system.
Memory Size
Changed
Memory size has changed since the last boot. If no
memory was added or removed, then memory may
be bad.
No Boot Device
Available
System did not find a device to boot.
Off Board Parity
Error
A parity error occurred on an off-board card. This
error is followed by an address.
On Board Parity Error
Parity Error
A parity error occurred in onboard memory. This
error is followed by an address.
A parity error occurred in onboard memory at an
unknown address.
NVRAM / CMOS /
PASSWORD cleared
by Jumper
NVRAM, CMOS, and passwords have been cleared.
The system should be powered down and the
jumper removed.
<CTRL_N> Pressed
CMOS is ignored and NVRAM is cleared. User must
enter Setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
117
BIOS POST Beep Codes
The table below lists the POST error beep codes. Prior to system video
initialization, the BIOS uses these beep codes to inform users of error
conditions. The beep code occurs only when a critical error occurs or
when the BIOS fails to boot to the operating system. Please note that
not all error conditions are supported by BIOS beep codes.
Number of Beeps
Description
1
2
3
4
5
6
Refresh failure
Parity cannot be reset
First 64 Kb memory failure
Timer not operational
Processor failure (Reserved; not used)
8042 GateA20 cannot be toggled (memory failure or
not present)
7
Exception interrupt error
8
Display memory R/W error
9
(Reserved; not used)
10
11
CMOS Shutdown register test error
Invalid BIOS (such as, POST module not found)
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
118
BIOS Recovery Beep Codes
Beeps
1
Reason
One long beep - video is active.
1-2
One long beep and two short beeps: Insert the BIOS recovery
diskette.
An error or warning condition at boot can result in a series of beeps
being issued known as "beep codes.” These beeps have a code that
identifies system or PCI card events. For example, some Acer RAID cards
have beep codes. Before checking for a system beep code error make
sure the PCI card is not causing the beeping.
Download from Www.Somanuals.com. All Manuals Search And Download.
119
Configuration and BIOS Select
Jumpers
CMOS CLEAR
BMC Control
2
Force Erase
3
4
PASSWORD CLEAR
5
Protect
6
Erase
7
A
8
RECOVERY BOOT
9
Normal Boot
10
Recovery Boot
11
B
J29 BIOS SEL
1-2 Normal Boot
(off of either bank)
2-3 Force Boot
(off of bank 0 BIOS)
2
3
2
3
Configuration Jumper [J17]
Jumper Name
CMOS clear
Pins
2-3
What happens at system reset...
If these pins are jumpered, the CMOS
settings will be cleared on the next reset.
These pins should be jumpered on 1-2 for
normal operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 BIOS setup
120
Jumper Name
Pins
What happens at system reset...
Password Clear
BIOS Recovery
6-7
If these pins are jumpered, administrator
and user passwords will be cleared on the
next reset. These pins should be
jumpered on 5-6 for normal operation.
10-11 If these pins are jumpered, the system
will attempt to recover the BIOS by
loading the BIOS code into the flash
device from a floppy disk. This jumper is
typically only used when the BIOS has
become corrupted. These pins should be
jumpered on 9-10 for normal operation.
BIOS Select Jumper [J29]
Pins
Operation
What happens at system reset...
Normal Boot
1-2
If these pins are jumpered, the board will
boot off of either BIOS (bank.0 or bank 1)
depending on which is available first.
Force Boot
2-3
If these pins are jumpered, the board will
boot off of bank 0 BIOS.
Download from Www.Somanuals.com. All Manuals Search And Download.
This chapter helps you identify and solve
problems that might occur while you are
using the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
123
For any problem that you are encountering, first ensure you are using
the latest firmware and files. Firmware upgrades include updates for
BIOS and the hot-swap controller (HSC). In addition to the server
firmware and files, also update any drivers used for components you
have installed in your system, such as video drivers, network drivers,
and SCSI drivers.
Acer provides a package called the “Platform Confidence Test” that
may help with your diagnostics.
Resetting the System
Before going through in-depth troubleshooting, attempt first to
perform reset your system using one of the methods below.
To do this:
Press
Soft boot reset to clear the system memory and reload the
operating system.
<Ctrl+Alt+Del>
Clear system memory, restart POST, and reload the
operating system.
Reset button
Power off/on
Cold boot reset. Turn the system power off and then on.
This clears system memory, restarts POST, reloads the
Problems following Initial System Installation
Problems that occur at initial system startup are usually caused by an
incorrect installation or configuration. Hardware failure is a less
frequent cause. If the problem you are experiencing is with a specific
software application, see "Problems with Newly Installed Application
Software".
First Steps Checklist
•
AC power available at the wall outlet?
•
Are the power supplies plugged in? Check the AC cable(s) on the
back of the chassis and at the AC source.
•
Are all cables correctly connected and secured?
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
124
•
Are the processors fully seated in their sockets on the server
board?
•
Are all standoffs in the proper location and not touching any
components, causing a potential short?
•
Are all add-in PCI boards fully seated in their slots on the server
board?
•
•
Are all jumper settings on the server board correct?
Are all jumper and switch settings on add-in boards and peripheral
devices correct? To check these settings, refer to the
manufacturer’s documentation that comes with them. If
applicable, ensure that there are no conflicts - for example, two
add-in boards sharing the same interrupt.
•
•
Are all peripheral devices installed correctly?
If the system has a hard disk drive, is it properly formatted or
configured?
•
•
•
Are all device drivers properly installed?
Are the configuration settings made in Setup correct?
Is the operating system properly loaded? Refer to the operating
system documentation.
•
•
Did you press the system power on/off switch on the control panel
to turn the server on (power on light should be lit)?
Is the system power cord properly connected to the system and
plugged into a NEMA 5-15R outlet for 100-120 V~ or a NEMA 6-
15R outlet for 200-240 V~?
•
Are all integrated components from the tested components lists?
Check the tested memory, and chassis lists, as well as the
supported hardware and operating system list.
Hardware Diagnostic Testing
This section provides a more detailed approach to identifying a
hardware problem and locating its source.
CAUTION : Turn off devices before disconnecting cables: Before
disconnecting any peripheral cables from the system, turn off the
system and any external peripheral devices. Failure to do so can
cause permanent damage to the system and/or the peripheral
devices.
Download from Www.Somanuals.com. All Manuals Search And Download.
125
1
Turn off the system and all external peripheral devices. Disconnect
each of device from the system, except for the keyboard and the
video monitor.
2
3
Make sure the system power cord is plugged into a properly
grounded AC outlet.
Make sure your video display monitor and keyboard are correctly
connected to the system. Turn on the video monitor. Set its
brightness and contrast controls to at least two thirds of their
display monitor).
4
If the operating system normally loads from the hard disk drive,
make sure there is no diskette in drive A and no CD-ROM disk in
the CD-ROM drive.
5
6
If the power LED does light, attempt to boot from a floppy
diskette or from a CD-ROM disk.
Turn on the system. If the power LED does not light, see "Power
Light Does Not Light".
Lights
As POST determines the system configuration, it tests for the presence
of each mass storage device installed in the system. As each device is
checked, its activity light should turn on briefly. Check for the
following:
Does the diskette drive activity light turn on briefly? If not, see
"Diskette Drive Activity Light Does Not Light".
of the light and steps to take to correct the problem.
Confirming Loading of the Operating System
Once the system boots up, the operating system prompt appears on
the screen. The prompt varies according to the operating system. If
the operating system prompt does not appear, see "No Characters
Appear on Screen".
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
126
Specific Problems and Corrective Actions
This section provides possible solutions for these specific problems:
•
•
•
•
•
•
•
•
•
Power light does not light.
No characters appear on screen.
Characters on the screen appear distorted or incorrect.
System cooling fans do not rotate.
Diskette drive activity light does not light.
Hard disk drive activity light does not light.
CD-ROM drive activity light does not light.
There are problems with application software.
The bootable CD-ROM is not detected.
Try the solutions below in the order given. If you cannot correct the
problem, contact your service representative or authorized dealer for
help.
Power Light Does Not Light
Check the following:
•
•
Did you press the power-on button?
Is the system operating normally? If so, the power LED might be
defective or the cable from the control panel to the server board
might be loose.
•
•
•
•
Have you securely plugged the server AC power cord into the
power supply?
Is the power supply correctly set to 110V or 235V, depending on
your power output?
Will other items plugged into the same power outlet function
correctly?
Some ATX power supplies have a power switch on the back of the
power supply, next to the fan. If your system has one, is it turned
on?
•
•
Remove all add-in cares and see if the system boots. If successful,
add the cards back in one at a time with a reboot between each
addition.
Make sure the memory DIMMs comply with the system
Download from Www.Somanuals.com. All Manuals Search And Download.
127
requirements.
•
Make sure the memory DIMMs have been populated according to
the system requirements.
•
•
•
Remove the memory DIMMs and re-seat them.
Make sure the processor(s) comply with the system requirements.
Make sure the processor(s) have been populated according to the
system requirements.
•
Remove the processor(s) and re-seat them.
Make sure the chassis standoffs are installed only below mounting
holes. Misplaced standoffs can contact the pins on the bottom of the
server board and cause a short.
No Characters Appear on Screen
Check the following:
•
Is the keyboard functioning? Test it by turning the “Num Lock”
function on and off to make sure the Num Lock light is
functioning.
•
•
Is the video monitor plugged in and turned on? If you are using a
switch box, is it switched to the correct system?
Are the brightness and contrast controls on the video monitor
properly adjusted?
•
•
Is the video monitor signal cable properly installed?
Does this video monitor work correctly if plugged into a different
system?
•
•
Is the onboard video controller enabled in the BIOS?
Remove all add-in cares and see if the video returns. If successful,
add the cards back in one at a time with a reboot between each
addition.
•
•
Make sure the memory DIMMs comply with the system
requirements.
Make sure the memory DIMMs have been populated according to
the system requirements.
•
•
•
Remove the memory DIMMs and re-seat them.
Make sure the processor(s) comply with the system requirements.
Make sure the processor(s) have been populated according to the
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
128
•
system requirements.
Remove the processor(s) and re-seat them.
If you are using an add-in video controller board, do the following:
1
2
Verify that the video works using the onboard video controller.
Verify that the video controller board is fully seated in the server
board connector.
3
4
Reboot the system for changes to take effect.
If there are still no characters on the screen after you reboot the
system and POST emits a beep code, write down the beep code
you hear. This information is useful for your service
representative.
5
If you do not receive a beep code and characters do not appear,
the video display monitor or video controller may have failed.
Contact your service representative or authorized dealer for help.
Characters Are Distorted or Incorrect
Check the following:
•
•
•
Are the brightness and contrast controls properly adjusted on the
video monitor? See the manufacturer’s documentation.
Are the video monitor’s signal and power cables properly
installed?
Does this video monitor work correctly if plugged into a different
system?
System Cooling Fans Do Not Rotate Properly
If the system cooling fans are not operating properly, it is an indication
of possible system component failure.
Check the following:
•
•
Is the power-on light lit? If not, see "Power Light Does Not Light".
If your system has LED lights for the fans, is one or more of these
LEDs lit?
•
•
Are any other control panel LEDs lit?
Have any of the fan motors stopped? Use the server management
subsystem to check the fan status.
Download from Www.Somanuals.com. All Manuals Search And Download.
129
•
Have your fans speeded up in response to an overheating
situation?
•
•
Have your fans speeded up in response to a fan that has failed?
Are the fan power connectors properly connected to the server
board?
•
•
•
Is the cable from the control panel board connected to the both
the control panel board and to the server board?
Are the power supply cables properly connected to the server
board?
Are there any shorted wires caused by pinched-cables or have
power connector plugs been forced into power connector sockets
the wrong way?
Diskette Drive Activity Light Does Not Light
Check the following:
•
•
Are the diskette drive’s power and signal cables properly installed?
Are all relevant switches and jumpers on the diskette drive set
correctly?
•
•
Is the diskette drive properly configured?
Is the diskette drive activity light always on? If so, the signal cable
may be plugged in incorrectly.
If you are using the onboard diskette controller, use the BIOS setup to
make sure that “Onboard Floppy” is set to “Enabled." If you are using
an add-in diskette controller, make sure that “Onboard Floppy” is set
to “Disabled.”
Optical Drive Activity Light Does Not Light
Check the following:
•
Are the CD-ROM/DVD-ROM drive’s power and signal cables
properly installed?
•
•
Are all relevant switches and jumpers on the drive set correctly?
Is the drive properly configured?
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
130
Cannot Connect to a Server
•
Make sure the network cable is securely attached to the correct
connector at the system back panel.
•
•
•
•
Try a different network cable.
Make sure you are using the correct and the current drivers.
Make sure the driver is loaded and the protocols are bound.
Make sure the hub port is configured for the same duplex mode as
the network controller.
•
•
Make sure the correct networking software is installed.
If you are directly connecting two servers (without a hub), you will
need a crossover cable.
•
Check the network controller LEDs next to the NIC connectors.
Problems with Network
The server hangs when the drivers are loaded.
•
Certain drivers may require interrupts that are not shared with
other PCI drivers. For these drivers, it may be necessary to alter
settings so that interrupts are not shared. See the documentation
that came with your PCI card(s) for information on changing
interrupts.
Diagnostics pass but the connection fails.
•
•
Make sure the network cable is securely attached.
Make sure you specify the correct frame type in your NET.CFG file.
The controller stopped working when an add-in adapter was
installed.
•
Make sure the cable is connected to the port from the onboard
network controller.
•
•
Make sure your BIOS is current.
Make sure the other adapter supports shared interrupts. Make
sure your operating system supports shared interrupts.
•
Try reseating the add-in adapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
131
The add-in adapter stopped working without apparent cause.
•
•
Try reseating the adapter first; then try a different slot if necessary.
The network driver files may be corrupt or deleted. Delete and
then reinstall the drivers.
•
Run the diagnostics.
System Boots when Installing PCI Card
System Server Management features require full-time “standby”
power. This means some parts of the system have power going to
them whenever the power cord is plugged in, even if you have turned
the system power off with the power button on the control panel. If
you install a PCI card with the AC power cord plugged in, a signal may
be sent to the command the system to boot. Before installing a PCI
card, you should always:
•
Turn off the server power by using the power button on the front
of the system.
•
Unplug the AC power cord(s) from the server.
Problems with Newly Installed Application
Software
Problems that occur when you run new application software are
usually related to the software, not the server hardware. Faulty
equipment is unlikely, especially if other software runs correctly.
Check the following:
•
•
•
•
•
Make sure the system meets the minimum hardware requirements
for the software. See the software documentation.
Make sure the software is properly installed and configured for
the system. See the software documentation.
Use only an authorized copy. Unauthorized copies often do not
work.
If you are running the software from a diskette, CD-ROM or DVD-
ROM, try a different diskette.
Make sure the correct device drivers installed.
If the problems persist, contact the software vendor’s customer service
representative.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
132
Problems with Application that Ran Correctly
Earlier
Problems that occur after the system hardware and software have
been running correctly sometimes indicate equipment failure.
However, they can also be caused by file corruption or changes to the
software configuration.
Check the following:
•
•
•
If you are running the software from a diskette, CD-ROM or DVD-
ROM, try a different diskette.
Uninstall and reinstall the software. Make sure all necessary files
are installed.
If the problems are intermittent, there may be a loose cable, dirt in
the keyboard (if keyboard input is incorrect), a marginal power
supply, or other random component failures.
•
If you suspect that a transient voltage spike, power outage, or
brownout might have occurred, reload the software and try
running it again. Symptoms of voltage spikes include a flickering
video display, unexpected system reboots, and the system not
responding to user commands.
Random errors in data files: If you are getting random errors in
your data files, they may be getting corrupted by voltage spikes
on your power line. If you are experiencing any of the above
symptoms that might indicate voltage spikes on the power line,
you may want to install a surge suppressor between the power
outlet and the system power cord.
Hard Drive(s) are not Recognized
Check the following:
•
•
Make sure the drive is not disabled in BIOS Setup.
Make sure the drive is connected correctly and that is plugged into
the power supply.
•
•
Make sure the drive is compatible.
Make sure you have not exceeded the power budget for the
server.
•
If using SCSI drives, verify that each SCSI ID number is unique on
Download from Www.Somanuals.com. All Manuals Search And Download.
133
the SCSI bus. See your drive documentation for details on setting
the SCSI ID for your drives.
•
•
If using ATA drives, verify that the master/slave settings are set
correctly. See your drive documentation for details on setting the
master/slave settings.
If using a RAID configuration with SCSI or SATA drives, make sure
the RAID card is installed correctly.
Bootable CD-ROM Is Not Detected
Check the following:
•
Make sure the BIOS is configured to allow the CD-ROM to be the
first bootable device.
LED Information
The Acer Altos G520 includes LEDs that can aid in troubleshooting your
system. A table of these LEDs with a description of their use is listed
below.
LED Name
Function
Location
Color
Correction
System
fault
Visible fault
warning
Control
Green or
Amber
•
Amber =
panel and
board rear
left corner
critical error or
non-
recoverable
•
Amber blink =
non-critical
ATA
activity
Control
panel
Control
panel and
board left
side
Green
Blinking =
Activity. No action
required.
Memory
fault 1-6
Identify
failing
DIMM end
front of
board
Amber
On = Fault
memory
module
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Troubleshooting
134
LED Name
Function
Location
Color
Correction
POST
Display
boot 80
POST code
Left rear of
board
Each LED
can be
Off,
See the POST code
table
code 1-4
(LSB, bit1,
bit2, MSB)
Green,
Amber,
Red
Fan Pack
Fault
Warn on
fan failure
Front center
board
Amber
Amber
Amber
On = Fault
On = Fault
On = Fault
CPU 1 & 2
Fan Fault
Identify fan
failure
Front center
board
CPU 1 & 2
Fan Fault
Identify
processor
failure
1” behind
processor
socket
5v
Standby
Identify 5v
standby
power on
state
Front left
board
Amber
Green
On = 5v standby
power on
Power
LED
Identify the
power state
of the
Control
panel
•
•
•
Off = Power is
off (off or S5)
On = Power on
or S0)
system
Slow Blink =
Low power
state (S1 - S3)
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to install the
ASM software package.
Download from Www.Somanuals.com. All Manuals Search And Download.
137
Installing ASM
Acer Server Manager (ASM) consists of the ASM Console and the ASM
Agent. These two components are both required to perform server
management tasks.
System requirements
ASM requires TCP/IP connectivity between the ASM Console and the
ASM Agent.
ASM Agent
•
•
•
•
Altos Server System
Min. of 128 MB RAM
SCSI/IDE hard drive with at least 100 MB free hard disk space
Microsoft Windows NT 4.0 or Windows 2000 Server/Advanced
Server operating system
ASM Console
•
•
•
•
Intel Pentium III (500 MHz) or higher processor
128 MB of RAM
SCSI/IDE hard drive with at least 100 MB free hard disk space
Microsoft Windows 2000 Professional/XP/Server/Advanced Server
operating system
•
Ethernet card
System setup
Make sure that your system meets the requirements listed above
before proceeding. You may also want to change your screen to
800 x 600 resolution or higher for optimum viewing.
Installing ASM Agent
To install ASM Agent:
1
Log in to the managed server using the Administrator account.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: ASM Quick Installation Guide
138
2
Insert the EasyBUILD Management CD into the server’s CD-ROM
drive.
The installation sequence will automatically be displayed.
Select the option for ASM installation.
3
4
The installation wizard will be initialized.
Follow all onscreen instructions to complete installation.
For detailed instructions on installing ASM Agent, refer to the
ASM User’s manual.
To launch the program, on the Windows taskbar click on the Start
button, point to Programs, select Acer Server Management Suite then
click ASM Agent.
Installing ASM Console
To install ASM Console:
1
Log in to the target Windows-based PC using the Administrator
account.
2
Insert the EasyBUILD Management CD into the computer’s
CD-ROM drive.
The installation sequence will automatically be displayed.
Select the option for ASM installation.
3
4
The installation wizard will be initialized.
Follow all onscreen instructions to complete installation.
For detailed instructions on installing ASM Console, refer to the
ASM User’s manual.
To launch the program, on the Windows taskbar click on the Start
button, point to Programs, select Acer Server Management Suite then
click ASM Console.
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to install the
optional rack mount kit for Acer Altos G520.
Download from Www.Somanuals.com. All Manuals Search And Download.
141
System rack installation
Aside from its tower configuration, the Altos G520 server system can
also be mounted in a rack-model position. A rack mount kit is
available for customers who want to mount a server tower system in a
server rack. To purchase a rack mount kit, contact your local Acer
representative or order directly from Acer.com.
The figure below shows the Altos G520 mounted in as a rack server
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Altos G520 Rack Installation Guide
142
Vertical mounting hole pattern
The four vertical rails of a rack contain mounting holes arranged in a
manner shown in the figure below:
The system occupies 5U in the rack. Count the U positions and hole
numbers from the bottom up.
Note: The unit of measurement used in this document is "U"
(1U = 1.75 inches or 44.45 mm). The total sum of the heights of all
components in the rack measured in "U" cannot exceed the
height of the rack. For more information, refer to the
documentation that came with your system rack.
The distance from the center of two holes with closer spacing to the
center of the next pair is equivalent to 1U.
When installing components, you must start your measurement from
the center of the two holes with closer spacing. Otherwise, the screw
holes on the component may not match those on the rack.
Download from Www.Somanuals.com. All Manuals Search And Download.
143
Screw types for rack installation
The following screws are used in the mounting process for the Acer
Altos G520 and other rack-mount components.
Screw type
Figure
Usage
1
2
#8-32 x 0.25 inch
Securing the inner mounting
rails to the server
Hex head
Attaching the side handles to
the server
#6-32 0.25 inch
3
4
M4 x L8
M4 nut
Securing the mounting
brackets to the inner sliding
piece
M6 x L10
Cage nut
Securing the cable carrier
and the mounting rails to the
rack
Supports the M6 metal
screws for securing server
components to the rack
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Altos G520 Rack Installation Guide
144
Installing the system into the rack
The Altos G520 Rack mount kit contains the server tray, two sets of
rack brackets and mounting rails. The rack brackets attach the server
tray to the mounting rails, which allow the server tray to slide in and
out of the server rack for maintenance purposes.
1
2
3
Remove all items from the rack mount kit package.
Extend the inner rail until the rail release latch clicks.
Press the release latch then slip the inner rail out.
Do the same thing with the other rack bracket.
4
Attach the inner rails to each side of the server tray with the
release catches toward the front end of the server tray.
Download from Www.Somanuals.com. All Manuals Search And Download.
145
Installing cage nuts
Cage nuts are used to secure system and other components to the
vertical rails in the rack.
To install cage nuts:
•
•
•
Insert the lower lip of the cage nut over the bottom of the
opening at the back of a rail.
With your fingers, pinch the cage nut rack fastener and push
in until the top lip locks into position.
Repeat this process to install the other cage nuts in their
appropriate locations.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Altos G520 Rack Installation Guide
146
5
Extend the middle sliding piece of each mounting rail forward
until it clicks.
6
Install the server tray into the rack by first carefully aligning the
inner rails with the fully extended middle mounting rails on the
rack. Press the release latch on both sides of the server and slide
the server tray.
Caution! To avoid personal injury, care should be taken when
pressing the component rail release latches and sliding the
component into the rack.
7
8
9
Place the system on the server tray with the removeable left panel
facing up.
Secure the system by tightening the two tooless screws at the back
of the server tray to back of the server.
Insert the power, peripheral and networking cables into the
appropriate ports. Refer to ”Connecting peripherals” on page 24
for detailed instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to create
SATA RAID.
Download from Www.Somanuals.com. All Manuals Search And Download.
149
Configuring the onboard SATA
RAID
This section briefly shows how to create RAID 1 (mirror) volume with
onboard SATA RAID function.
How to enable the onboard SATA RAID
function
Load BIOS default setting
1
Power on the server to start the system POST (Power On Self Test)
process. During bootup, press <F2> to enter the BIOS setup screen.
2
Press <F9> to load BIOS default setting and press <F10> save the
configuration changes and exit setup.
Enable onboard SATA RAID function
1
2
3
In the BIOS Setup Utility, move cursor to <Advanced>. Then select
<IDE Configuration> and press Enter.
Move cursor to Configure S-ATA as RAID and press Enter to change
the Options to [Enabled].
Press <F10> save the configuration changes and exit setup.
How to create RAID 1 volume
Enter the onboard SATA RAID Configuration Utility
When you see the Intel Embedded Server RAID information shows on
the screen during the POST (Power-On Self Test), press <Ctrl> + <E> to
enter the Embedded RAID Configuration Utility.
Loading onboard SATA RAID default setting
1
2
3
Select Objects from Management menu.
Select Adapter from Objects. The selectable adapter will be listed.
Press Enter on the adapter and the adapter setting will be shown
on the screen. You can change the setting from this menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: SATA RAID Configuration
150
4
5
Select Factory Default and YES to load the default settings.
Exit the configuration utility and press <Ctrl> + <Alt> + <Del> to
reboot the server.
Create RAID 1 volume
1
2
Select Configuration from Management Menu.
Select New Configuration from the Configuration menu and select
YES to continue. An array selection window displays the devices
connected to the current controller.
3
4
Press the arrow keys to choose specific physical drives and press
spacebar to associate the selected drive with the current array. The
indicator for selected drive change from READY to ONLINE
Add 2 drives to current array and press <Enter> to finish creating
current array.
5
6
Press Enter again to select array to configure.
Press spacebar to select the array and press <F10> to configure the
logical drive
7
The default RAID level for 2 disk drives is RAID1. Just select Accept
to use the default setting and press <Enter> to return to the
ARRAY SELECTION MENU.
8
9
Press <Enter> to end the array configuration.
Select YES to Save Configuration and press any key to return to the
Configure menu.
Initial RAID Volume
1
2
Press <Esc> to return to the Management Menu.
Select Initialize from Management menu. All logical drives should
be listed under Logical Drives.
3
4
Press <Spacebar> to select drives for initialization. The selected
drive will be shown in yellow.
After selecting the drives, press <F10> and select YES to start the
initialization process.
5
6
When initialization is complete, press any key to continue.
Press <Esc> to return to the Management Menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
151
Save and Exit Embedded RAID Configuration Utility
1
When RAID configuration and initialization is complete, press
<Esc> in the Management Menu and select YES to exit the
Embedded RAID Configuration Utility.
2
Press <Ctrl> + <Alt> + <Del> to reboot the server. Now you can
start installing an OS on the RAID array.
NOTE: You can find the onboard SATA RAID driver in the
EasyBUILD™ Resource CD and SATA RAID utility in the
EasyBUILD™ Management CD.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: SATA RAID Configuration
152
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix shows you how to create
RAID.
Download from Www.Somanuals.com. All Manuals Search And Download.
155
Configuring the SCSI/SCSI RAID
HBA
This section briefly shows how to create a RAID 1 (mirror) volume. This
feature requires installation/presence of LSI Logic 20320-R or LSI Logic
22320-R U32 SCSI controllers.
How to use SCSI HBA setup utility
During the Power-On Self Test (POST), press <Ctrl > + <C> to enter the
LSI Logic Configuration Utility.
Loading HBA Default Settings
1
In the LSI Logic MPT SCSI Setup Utility, please press F2 and select
Global Properties. Then, select <Restore Defaults>.
2
3
4
5
Press ESC, then select <Save changes then exit this menu>.
Move cursor to <53C1020/1030> and press Enter.
Move cursor to <Restore Defaults> and press Enter.
Press ESC, then select <Save changes then exit this menu>.
How to use SCSI RAID HBA setup utility
How To Create RAID 1 (Mirror) volume with a Hot
Spare Disk
1
In the LSI Logic MPT SCSI Setup Utility, please select <53C1020/
1030> and press Enter.
2
3
Move cursor to <RAID Properties> and press Enter.
In Array Disk field, press Space key to change the hard disk to
[Yes].
Note: In the Array Disk field, if you change settings, you will see
the following messages. Press the DELETE key to erase data.
F3 - keep Data (Create 2 disk array)
Delete - Erase Disk (Create 2 to 6 disk array)
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: RAID Configuration
156
4
In Hot Spare field, press Space key to change the hard disk to [Yes].
Note: In the Hot Spare field, if you change settings, you will see
the following messages. Press the DELETE key to ignore it.
WARNING: Data on drive will be LOST!
Press DELETE if data loss OK or any other key to cancel.
Press ESC, then select <Save changes then exit this menu>.
5
RAID Volume Initialization
After you create RAID volume and save the changes, the disk controller
will initialize RAID volume automatically. As LSI Logic 20320-R/22320-R
can support background initialization, you don’t have to wait for the
initialization to complete. Now, you can exit LSI Logic Configuration
Utility.
Exit and Restart the server
1
Press ESC, then select <Exit the Configuration Utility>. Then, you
will see a [Global properties saved. Hit any key to reboot.]
message.
2
Press a key to reboot system.
MegaRAID Configuration Utility
Turn on the system power. When prompted, press <Ctrl> + <M> to
enter the MegaRAID Configuration Utility. After entering the
MegaRAID Configuration Utility, you will see the Management Menu
on the screen.
Load RAID Card Default Setting
1
2
Select Objects from Management menu.
Select Adapter from Objects. The adapter setting will be shown on
the screen. You can change the setting from this menu.
3
4
Select Factory Default and YES to load the default settings.
Press <Ctrl> + <Alt> + <Del> to reboot the server.
Download from Www.Somanuals.com. All Manuals Search And Download.
157
Create RAID1 Volume
1
After the server has rebooted, press <Ctrl> + <M> to enter the
MegaRAID Configuration Utility again.
2
3
Select Configuration from Management Menu.
Select New Configuration from the Configuration menu and select
YES to continue. An array selection window displays the devices
connected to the current controller.
4
Press the arrow keys to choose specific physical drives and press
spacebar to associate the selected drive with the current array. The
indicator for selected drive change from READY to ONLINE A[array
number]-[drive number]. For example, ONLINE A1-2 means disk
drive 2 in array 1.
5
Add 2 drives to current array and press <Enter> to finish creating
current array.
6
7
Press <F10> to configure the logical drives.
The default RAID level for 2 disk drives is RAID1. Just select Accept
to use the default setting and press <Enter> to return to the
ARRAY SELECTION MENU.
8
9
Press <Enter> to end the array configuration.
Select YES to Save Configuration and press any key to return to the
Configure menu.
Assign Hot Spare Disk
1
2
Select Add/View Configuration from Configuration menu.
Press arrow keys to choose specific physical drives and press <F4>
to set the drive as Hot Spare Disk. Select YES to confirm and the
indicator for selected drive change from READY to HOTSP.
3
4
Press <Esc> to end the array configuration.
Select YES to Save Configuration and press any key to return to the
Configure menu.
Initialize RAID Volume
1
2
Press <Esc> to return to the Management Menu.
Select Initialize from Management menu. All logical drives should
be listed under Logical Drives.
3
Press <Spacebar> to select drives for initialization. The selected
drive will be shown in yellow.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: RAID Configuration
158
4
After selecting the drives, press <F10> and select YES to start the
initialization process.
5
6
When initialization is complete, press any key to continue.
Press <Esc> to return to the Management Menu.
Save And Exit MegaRAID Configuration Utility
1
When RAID configuration and initialization is complete, press
<Esc> in the Management Menu and select YES to exit the
MegaRAID Configuration Utility.
2
Press <Ctrl> + <Alt> + <Del> to reboot the server. Now you can
start installing an OS on the RAID array.
Download from Www.Somanuals.com. All Manuals Search And Download.
This appendix includes tables of codes and
error messages that may be encountered
when operating the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
161
POST Code Checkpoints
Each of the four LEDs can have one of four states: Off, Green, Red, or
Amber. The LED diagnostics feature consists of a hardware decoder
and four dual color LEDs. During POST, the LEDs will display all normal
Port80 codes representing the progress of the BIOS POST. Each
postcode will be represented by a combination of colors from the 4
LEDs. During the POST process, each light sequence represents a
specific Port-80 POST code. If a system should hang during POST, the
Diagnostic LEDs will present the last test executed before the hang.
When reading the lights, the LEDs should be observed from the back of
the system.
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A+Amber
Description
MSB
LSB
03
OFF
OFF
G
G
Disable NMI, parity, video
for EGA, and 03DMA
controllers. Initialize BIOS,
POST, Run-time data area.
Initialize BIOS modules on
POST entry and GPNV
area. Initialized CMOS as
mentioned in the Kernel
Variable “wCMOSFlags”
04
OFF
G
OFF
OFF
Check CMOS diagnostic
byte to determine if
battery power is OK and
CMOS checksum is OK.
Verify CMOS checksum
manually by reading
storage area. If the CMOS
checksum is bad, update
CMOS with power-on
default values and clear
passwords. Initialize status
register A.
Initializes data variables
that are based on CMOS
setup questions. Initializes
both the 8259 compatible
PICs in the system
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F: Diagnostic Code Checkpoints
162
Diagnostic LED Decoder
G=Green, R=Red, A+Amber
Check
point
Description
MSB
LSB
05
OFF
G
G
OFF
G
Initializes the interrupt
controlling hardware
(generally PIC) and
interrupt vector table.
06
OFF
G
OFF
Do R/W test to CH-2 count
reg. Initialize CH-0 as
system timer. Install the
POSTINT1Ch handler.
Enable IRQ-0 in PIC for
system timer interrupt.
Traps INT1Ch vector to
"POSTINT1ChHandlerBloc
k."
08
G
OFF
OFF
OFF
Initializes the CPU. The
BAT test is being done on
KBC. Program the
keyboard controller
command byte is being
done after Auto detection
of KB/MS using AMI KB-5.
CO
R
R
OFF
OFF
Early CPU Init Start --
Disable Cache - Init Local
APIC
C1
C2
C5
C6
C7
R
R
R
R
R
R
OFF
G
G
Set up boot strap
processor information
R
OFF
G
Set up boot strap
processor for POST
A
A
A
OFF
G
Enumerate and set up
application processors
OFF
G
Re-enable cache for boot
strap processor
G
Early CPU Init Exit
Download from Www.Somanuals.com. All Manuals Search And Download.
163
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A+Amber
Description
MSB
LSB
0A
G
OFF
G
OFF
Initializes the 8042
compatible Key Board
Controller
0B
0C
0E
G
G
G
OFF
G
G
G
Detects the presence of
PS/2 Mouse
OFF
G
OFF
OFF
Detects the presence of
Keyboard in KBC Port
G
Testing and initialization
of different Input Devices.
Also, update the Kernel
Variables.
Traps the INT09h vector,
so that the POST INT09h
handler gets control for
IRQ1. Uncompress all
available language, BIOS
logo, and Silent logo
modules.
13
24
OFF
OFF
OFF
G
G
R
A
Early POST initialization of
chipset registers
OFF
Uncompress and initialize
any platform specific BIOS
modules
30
OFF
G
OFF
OFF
R
R
Initialize System
Management Interrupt
2A
A
OFF
Initializes different devices
through DIM. See DIM
Code Checkpoints section
of document for more
information
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F: Diagnostic Code Checkpoints
164
Diagnostic LED Decoder
G=Green, R=Red, A+Amber
Check
point
Description
MSB
LSB
2C
G
G
R
OFF
Initializes different
devices. Detects and
initializes the video
adapter installed in the
system that have optional
ROMs
2E
31
G
G
A
R
OFF
A
Initializes all the output
devices
OFF
OFF
Allocate memory for ADM
module and uncompress
it. Give control to ADM
module for initialization.
Initialize language and
font modules for ADM.
Activate ADM module.
33
37
OFF
OFF
OFF
A
A
A
A
Initializes the silent boot
module. Set the window
for displaying text
information.
G
Displaying sign-on
message, CPU
information, setup key
message, and any OEM
specific information.
38
G
OFF
R
R
Initializes different devices
through DIM. See DIM
Code Checkpoints section
of document for more
information.
39
G
G
OFF
OFF
R
A
R
Initializes DMAC-1 and
DMAC-2.
3A
A
Initialize RTC date/time
Download from Www.Somanuals.com. All Manuals Search And Download.
165
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A+Amber
Description
MSB
LSB
3B
G
OFF
R
A
Test for total memory
installed in the system.
Also, check for DEL or ESC
keys to limit memory test.
Display total memory in
the system.
3C
40
G
G
R
R
R
Mid POST initialization of
chipset registers.
OFF
OFF
OFF
Detect different devices
(Parallel ports, serial ports,
and coprocessor in
CPU...etc). successfully
installed in the system and
update the BDA,
EBDA...etc.
50
52
OFF
OFF
R
R
OFF
R
R
Programming the memory
hole or any kind of
implementation that
needs an adjustment in
system RAM size if
needed.
G
Updates CMOS memory
size from memory found
in memory test. Allocates
memory for Extended
BIOS Data Area from base
memory.
60
75
OFF
OFF
R
R
R
OFF
A
Initializes NUM-LOCK
status and programs the
KBD typematic rate.
A
Initialize Int-13 and
prepare for IPL detection.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F: Diagnostic Code Checkpoints
166
Diagnostic LED Decoder
G=Green, R=Red, A+Amber
Check
point
Description
MSB
LSB
78
G
R
R
R
Initializes IPL devices
controlled by BIOS and
option ROMs.
7A
7C
G
G
R
A
R
R
R
Intializes remaining
option ROMs.
A
Generate and write
contents of ESCD in
NVRam.
84
85
R
R
G
G
OFF
OFF
OFF
G
Log errors encountered
during POST.
Display errors to the user
and get the user response
for error.
87
8C
8D
8E
R
G
G
G
G
G
G
Execute BIOS setup if
needed/requested.
A
A
A
OFF
OFF
G
OFF
G
Late POST initialization of
chipset registers.
Build ACPI tables (if ACPI
supported).
OFF
Program the peripheral
parameters. Enable/
Disable NMI as selected
90
R
OFF
OFF
R
Late POST initialization of
system management
interrupt.
A0
A1
R
R
OFF
OFF
R
R
OFF
G
Check boot password if
installed
Clean-up work needed
before booting to
operating system.
Download from Www.Somanuals.com. All Manuals Search And Download.
167
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A+Amber
Description
MSB
LSB
A2
R
OFF
A
OFF
Takes care of runtime
image preparation for
different BIOS modules.
Fill the free area in F000h
segment with 0FFh.
Initializes the Microsoft
IRQ Routing Table.
Prepares the runtime
language module.
Disables the system
configuration display if
needed.
A4
A7
R
R
G
G
R
OFF
G
Initialize runtime
language module.
A
Displays the system
configuration screen if
enabled. Initialize the
CPU’s before boot, which
includes the programming
of the MTRR’s.
A8
A
OFF
R
OFF
Prepare CPU for operating
system boot including
final MTRR values.
A9
A
A
OFF
OFF
R
G
Wait for user input at
config display if needed.
AA
A
OFF
Uninstall POST INT1Ch
vector and INT09h vector.
Deinitializes the ADM
module.
AB
AC
A
A
OFF
G
A
R
G
A
Prepare BBS for Int 19
boot.
End of POST initialization
of chipset registers.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F: Diagnostic Code Checkpoints
168
Diagnostic LED Decoder
G=Green, R=Red, A+Amber
Check
point
Description
MSB
LSB
B1
00
R
OFF
OFF
R
A
Save system context for
ACPI.
OFF
OFF
OFF
Passes control to OS
Loader (typically INT19h).
Bootblock Initialization Code Checkpoints
The Bootblock initialization code sets up the chipset, memory and
other components before system memory is available. The following
table describes the type of checkpoints that may occur during the
bootblock initialization portion of the BIOS:
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A+Amber
Description
MSB
LSB
Before D1
Early chipset initialization
is done. Early super I/O
initialization is done
including RTC and
keyboard controller. NMI
is disabled.
D1
R
R
OFF
A
Perform keyboard
controller BAT test. Check
if waking up from power
management suspend
state. Save power-on
CPUID value in scratch
CMOS.
D0
R
R
OFF
R
Go to flat mode with 4GB
and GA20 enabled. Verify
the bootblock checksum.
Download from Www.Somanuals.com. All Manuals Search And Download.
169
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A+Amber
Description
MSB
LSB
D2
D3
R
R
R
G
G
R
Disable CACHE beforfe
memory detection.
Execute full memory sizing
module. Verify that flate
mode is enabled.
R
A
Disable CACHE before
memory detection.
Execute full memory sizing
module. Verify that flat
mode is enabled.
D4
D5
R
R
A
A
OFF
OFF
R
Test base 512KB memory.
Adjust policies and cache
first 8MB.
A
Bootblock code is copied
from ROM to lower system
memory and control is
given to it. BIOS now
executes out of RAM.
D6
R
A
G
R
Both key sequence and
OEM specific method is
checked to determine if
BIOS recovery is forced.
Main BIOS checksum is
tested. If BIOS recovery is
necessary, control flows to
checkpoint E0. See
Bootblock Recovery Code
Checkpoints section of
document for more
information.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F: Diagnostic Code Checkpoints
170
Diagnostic LED Decoder
G=Green, R=Red, A+Amber
Check
point
Description
MSB
LSB
D7
R
A
G
A
Restore CPUID value back
into register. The
Bootblock-Runtime
interface module is moved
to system memory and
control is given to it.
D8
D9
A
A
R
R
OFF
OFF
R
The Runtime module is
uncompressed into
memory. CPUID
information is stored in
memory.
A
Store the Uncompressed
pointer for future use in
PMM. Copying Main BIOS
into memory. Leaves all
RAM below 1MB Read-
Write including E000 and
F000 shadow areas but
closing SMRAM.
DA
A
R
G
R
Restore CPUID value back
into register. Give control
to BIOS POST (Execute
POST Kernel). See POST
Code Checkpoints section
of document for more
information.
Download from Www.Somanuals.com. All Manuals Search And Download.
171
Bootblock Recovery Code Checkpoint
The bootblock recovery code gets control when the BIOS determines
that a BIOS recovery needs to occur because the user has forced the
update or the BIOS checksum is corrupt. The following table describes
the type of checkpoints that may occur during the Bootblock recovery
portion of the BIOS:
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A=Amber
Description
MSB
LSB
OFF
E0
R
R
R
Initialize the floppy
controller in the super I/O.
Some interrupt vectors are
intialized. DMA controller
is initialized. 8259
interrupt controller is
initialized. L1 cache is
enabled.
E9
A
R
R
OFF
Set up floppy controller
and data. Attempt to read
from floppy. Determine
information about root
directory of recovery
media.
EA
A
R
A
OFF
Enable ATAPI hardware.
Attempt to read from
ARMD and ATAPI CD-
ROM. Determine
information about root
directory of recovery
media.
EB
A
R
A
G
Disable ATAPI hardware.
Jump back to checkpoint
E9.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F: Diagnostic Code Checkpoints
172
Diagnostic LED Decoder
G=Green, R=Red, A=Amber
Check
point
Description
MSB
A
LSB
EF
A
R
A
R
G
Read error occured on
media. Jump back to
checkpoint EB.
F0
R
R
Search for pre-defined
recovery file name in root
directory.
F1
F2
R
R
R
R
R
A
R
Recovery file not found.
A
Start reading FAT table
and analyze FAT to find
the clusters occupied by
the recovery file.
F3
R
R
A
A
Start reading the recovery
file cluster by cluster.
F5
R
A
R
R
A
R
Disable L1 cache.
FA
A
A
Check the validity of the
recovery file configuration
to the current
configuration of the flash
part.
FB
A
R
A
A
Make flash write enabled
through chipset and OEM
specific method. Detect
proper flash part. Verify
that the found flash part
size equals the recovery
file size.
F4
R
A
R
R
The recovery file size does
not equal the found flash
part size.
FC
A
A
A
A
R
R
R
Erase the flash part.
FD
A
Program the flash part.
Download from Www.Somanuals.com. All Manuals Search And Download.
173
Diagnostic LED Decoder
Check
point
G=Green, R=Red, A=Amber
Description
MSB
A
LSB
FF
A
A
A
The flash has been
updated successfully.
Make flash write disabled.
Disable ATAPI hardware.
Restore CPUID value back
into register. Give control
to F000 ROM and
F000:FFF0h.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F: Diagnostic Code Checkpoints
174
Download from Www.Somanuals.com. All Manuals Search And Download.
175
Serial Console Features
103
System Management 102
Index
A
Acer Server Manager (ASM)
137
BPL4 cage configuration 43
installing cage 46
system requirements 137
ASM Agent 137
system setup 137
Caring features
CPU
5
removing 55
install ASM Agent 137
install ASM Console 138
D
DIMM
installing 60
B
BIOS setup 71
Advanced 76
Boot Settings Configuration
expansion card
91
Floppy Configuration 83
IDE Configuration 78
Primary/Secondary/
I
Slave 80
Memory Configuration 88
PCI Configuration 87
Processor Summary and
MegaRAID Configuration 156
Memory
3
77
USB Configuration 85
Boot 90
Boot Device Priority 92
remove side panel 41
Removable Devices 95
entering 72
Exit 107
P
Main 74
Security 97
peripherals 24
keyboard 24
monitor 26
power cable 27
power supply module
installing 67
removing the User pass-
word 99
Supervisor password 97
User password 97
Server 100
Event Log Configuration
105
Processor
3
Download from Www.Somanuals.com. All Manuals Search And Download.
176
system upgrade 37
S
SCSI cable cage configuration 49
installing cage 51
installing hard disk 50
removing cage 51
SCSI HBA setup 155
SCSI RAID HBA 155
SCSI RAID HBA setup 155
ESD precautions 37
post-installation instructions 38
preinstallation instructions 37
T
turning off the system 33
turning on the system 28
power-on problems 29
Serial ATA ports
Storage
system boards 14
mainboard layout 14
4
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Acer Computer Monitor Aspire L200 User Manual
ADTRAN Modem 1200153L1 User Manual
ADTRAN Network Router T1 FT1 CSU User Manual
Aico Smoke Alarm RFD User Manual
Alpine Car Video System PKG RSE3DVD User Manual
Altec Lansing Speaker IM5 User Manual
American Standard Fan 41011 User Manual
Badger Basket Baby Carrier 00569 User Manual
Barco Projection Television R9001280 User Manual
Beko Clothes Dryer DPU 8360 W User Manual