The 4000/7000DLT
Tabletop Series
Installation and
Operation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Associated Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Explanation of Symbols and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
2
Description
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Front Panel Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Other Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
SCSI Host Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
SCSI Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Application Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
3
Safety
Safety Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
4
Installation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Unpacking and Inspecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Installing the Host Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Connecting the Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Connecting More than One 4000/ 7000DLT Series . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Setting the SCSI ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Check the SCSI Bus Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Connecting Power and Turning On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Installing the Backup Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
5
Operation and Maintenance
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Power-on Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Drive Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
iv
Contents
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Drive Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Loading the Data Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Tape in Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Removing the Data Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Cleaning the Tape Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Cleaning the Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
6
Troubleshooting and Diagnostic
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Use Cleaning Tape LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Why the Use Cleaning Tape LED Gets Turned ON . . . . . . . . . . . . . . . . . . . . . . . . 7-6
High Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
A
Specification
General Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Contents
v
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Drive Configuration
Drive Dependent Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
SCSI Bus Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
DLT4000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
DLT7000 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
SCSI Bus Termination and Terminator Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
DLT4000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
DLT7000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-7
C
Regulatory Notices
FCC Notices (U.S. Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Shielded Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Product Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
IC Notice (Canada Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
EN 55022 Compliance (Czech Republic Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
CE Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
VCCI Notices (Japan Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Index
vi
Contents
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Figure 4-1
Figure 4-2
Figure 5-1
Figure B-1
Figure B-2
Figure B-3
Figure B-4
Figure B-5
Figure B-6
Figure B-7
Figure B-8
7000DLT Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
4000DLT Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
7000DLT Series Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
DLT Data Cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Cable Diagram for 4 4000/ 7000DLT Series Units. . . . . . . . . . . . . . . . 4-4
SCSI ID Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Loading a Data Cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
DLT4000 Tape Drive Connectors (Left Side). . . . . . . . . . . . . . . . . . . .B-3
Disable Parity Pins on SCSI ID Connector. . . . . . . . . . . . . . . . . . . . . .B-3
DLT7000 Tape Drive Connectors (Right Side) . . . . . . . . . . . . . . . . . .B-4
Disable Parity Pins on DFDT Connector . . . . . . . . . . . . . . . . . . . . . . .B-4
DLT4000 Tape Drive Connectors (right side) . . . . . . . . . . . . . . . . . . .B-5
TRM PWR/ TRM ENB Jumper Position . . . . . . . . . . . . . . . . . . . . . . . .B-6
DLT7000 Tape Drive Connectors (right side) . . . . . . . . . . . . . . . . . . .B-7
Term Power Pins on TRM PWR Connector. . . . . . . . . . . . . . . . . . . . .B-7
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
Figures
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table 2-1
Table 2-2
Table 2-3
Table 2-4
Table 2-5
Table 2-6
Table 2-7
Table 3-1
Table 5-1
Table 5-2
Table 5-3
Table 5-4
Table 5-5
Table 5-6
Table 5-7
Table 6-1
Table A-1
Maximum Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Transfer Rate (Compressed Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Drive to Model Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Front Panel Indicators and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Rear Panel Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Media Cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Cartridge Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Hazard Alert Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Drive States Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Drive Status LCD Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Operating Condition Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Drive Operation LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Tape in Use Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Using the Cleaning Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Cleaning Cycle LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Problem Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Tables
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Associated Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Explanation of Symbols and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2
Introduction
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
1-
Overview
This manual contains information and instructions necessary
for the safe operation of the 4000/ 7000DLT Series. The topics
discussed in this chapter are:
•
•
•
•
•
•
Overview
Intended Audience
Organization
Associated Documents
Explanation of Symbols and Notes
Assistance
Intended Audience
This guide is intended for operators, trained customer
specialists, and maintenance personnel of the service partner
who interact with the 4000/ 7000DLT Series.
Organization
This publication contains chapters detailing the operation of
the 4000/ 7000DLT. The chapters topics include:
Chapter 1
Introduction - Describes the overview,
intended audience, organization,
associated documents, explanation of
symbols and notes, and how to obtain
additional assistance.
Chapter 2
Chapter 3
Description - Describes general information
about the 4000/ 7000DLT Series.
Safety - Describes the hazard symbols,
messages, safety features, and operational
considerations for the safe operation of the
4000/ 7000DLT Series.
Chapter 4
Chapter 5
Installation - Describes the functional
installation of the 4000/ 7000DLT Series.
Installation and Operation - Describes the
proper installation instructions and
operational characteristics of the
4000/ 7000DLT Series.
Overview
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Troubleshooting and Diagnostic - Describes
the troubleshooting and diagnostic
techniques for the 4000/ 7000DLT Series.
Appendix A
Appendix B
Specifications - Outlines the specifications of
the 4000/ 7000DLT Series.
Drive Configuration - Describes the specific
information necessary to configure the
4000/ 7000DLT Series.
Index
Associated Documents
None.
Explanation of Symbols and Notes
The following symbols and highlighted passages note
important information. Detailed explanations of these
symbols are found in Hazard Alert Messages on page 3-3.
Detailed explanations for the above symbols are provided in
Hazard Alert Messages on page 3-3.
<1> + <2>
Italics
Press these keys simultaneously.
Headline, e. g., Chapter Name, Description
Special Term, e. g., Utilities.
Bold
Courier
Terms appearing on the operating panel,
switch position, e. g., ON, OFF
1-4
Introduction
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Description
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Front Panel Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Other Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
SCSI Host Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
SCSI Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Application Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Additional Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2
Description
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
2-
Overview
This section of the document provides a physical description
of the switches, indicators and connectors on the front and
rear panels of the 4000/ 7000DLT Series. Additional
information describes other requirements (additional
hardware and/ or software) needed to utilize the
4000/ 7000DLT Series.
Description
The 4000/ 7000DLT Series consists of two models, the
DLTTM4000 and the DLTTM7000. They are all SCSI-2
compatible, high performance, streaming tape cartridge data
storage devices designed for storage of near-line and off-line
data. All models use data compression, compaction, and
Digital Linear Tape (DLT) to obtain the capacities shown in
Table 2-1. The 4000/ 7000DLT Series are equipped with a 2-
line by 20-character backlit LCD display. The LCD displays
drive status messages, error messages, and drive Power-On
Self-Test (POST) results messages.
Table 2-1
Maximum Capacity
Model
DLTTape III
DLTTape IIIXT
DLTTape IV
4000DLT
10 GB (native)
15 GB (native)
20 GB (native)
20 GB (compressed) 30 GB (compressed)
40 GB (compressed)
7000DLT
10 GB (native) 15 GB (native)
35 GB (native)
20 GB (compressed) 30 GB (compressed)
70 GB (compressed)
The 4000/ 7000DLT Series are equipped with a 5 1/4 inch form
factor, half-inch tape drive. The design includes a dual-
channel read/ write head, Digital Lempel-Ziv (DLZ) high-
efficiency data compression, and tape mark directory to
maximize data throughput and minimize data access time.
Used for unattended backups or archiving, the 4000/ 7000DLT
Series allows you to back up a higher data capacity at higher
speed than either 8mm or 4mm DAT-based drives. Table 2-2
lists the maximum compressed mode transfer rates of the two
models:
Overview
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2-2
Model
Transfer Rate (Compressed Mode)
Maximum
Maximum
(Read Operation)
Sustained
(Write Operation)
4000DLT
7000DLT
3.0 MB/ sec
10.0 MB/ sec
3.0 MB/ sec
10.0 MB/ sec
3.5 MB/ sec
10.0 MB/ sec
The removable tape media cartridge allows long-term off-line
and/ or off-site data storage. The tape media is rated at up to
500,000 passes and has a shelf life of up to 30 years providing
superior media durability and data reliability.
Table 2-3 on page 2-4 lists the drive models used in the
4000/ 7000DLT Series. Tape density is selected either from the
drive front panel or the host. The 4000DLT, and 7000DLT
drives can read/ write 2.6, 6.0, and 10.0 GB formatted tapes for
100% interchange compatibility with earlier DLT drives.
Table 2-3
Model
Drive to Model Identification
Drive Model
4000DLT
7000DLT
DLT4000
DLT7000
The 4000/ 7000DLT Series includes Flash EEPROM
technology that allows easy on-site installation of firmware
updates from tape or from the host.
The 4000/ 7000DLT Series includes embedded diagnostic
software that tells you when head cleaning is required,
diagnostic results, and drive operating status. The drive has
embedded data logging of errors for failure analysis.
Front Panel Controls and Indicators
Figure 2-1 on page 2-5, and Figure 2-2 on page 2-6 show the
controls and indicators located on the front panel of the
4000/ 7000DLT Series.
2-4
Description
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-1
7000DLT Front Panel
Description
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-2
4000DLT Front Panel
2-6
Description
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2-4
Front Panel Indicators and Controls
2-line by 20-character Displays drive status, error messages, POST results
LCD Display
Beeper
Sounds whenever it is OK to operate the cartridge insert/
release handle. The green Operate Handle LED should be
ON whenever the Beeper sounds.
Write Protected
(orange)
ON = Tape write-protected.
OFF = Tape write enabled.
Tape in Use
Blinking = Tape moving.
(yellow)
ON = Tape loaded; ready for use.
Use Cleaning Tape
(yellow)
ON = Drive head needs cleaning, or the tape is bad.
OFF = cleaning complete, or cleaning unnecessary.
Operate Handle
(green)
ON = OK to operate the cartridge insert/ release handle.
OFF = Do not operate the cartridge insert/ release handle.
Density Select 2.6
ON = Tape is recorded in 2.6 GB format.
(yellow)
Blinking = Tape is recorded in another density.
Density Select 6.0
ON = Tape is recorded in 6.0 GB format.
(yellow)
Blinking = Tape is recorded in another density.
Density Select 10.0
ON = Tape is recorded in 10.0 GB format.
(yellow)
Blinking = Tape is recorded in another density.
Density Select 20.0
(yellow) [4000DLT
only]
ON = Tape is recorded in 20.0 GB format.
Blinking = Tape is recorded in another density.
Density Select 70.0
(yellow) [7000DLT
only]
ON = Tape is recorded in 70.0 GB format.
Blinking = Tape is recorded in another density
Compress
(yellow)
ON = Compression mode enabled.
OFF = Compression mode disabled.
Density Override
(yellow)
ON = Density selected from front panel.
OFF (default) = Density selected from host.
Blinking = In density selection mode.
Unload Button
Pressing this button initiates a manual unload of the tape.
This may take from 10 seconds to 4 minutes depending on
tape position.
Cartridge Insert/
Release Handle
Lift this handle (only when the Operate Handle LED is ON,
and after the momentary beep sounds) to load or eject a
cartridge from the drive. The handle lifts to the open
position and lowers to the closed position.
Description
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel Controls and Connectors
Figure 2-3 on page 2-8 shows the controls and connectors
located on the rear panel of the 7000DLT Series.
3
AC Power
Connector
Pow er
Switch
SCSI ID
Sw itch
SCSI Channel
Connectors
Figure 2-3
7000DLT Series Rear Panel
Table 2-5 describes the controls and connections.
Table 2-5
Rear Panel Controls and Connectors
Control or Connector
Purpose
Power Switch
Turns power to the unit on and off.
Receptacle for AC power cord.
AC Power Connector
SCSI Channel Connectors
Connections for the interface cable that connects the
unit with the host computer and/ or to other devices
on the SCSI channel. The interface cable can be
attached to either connector.
The 7000DLT, a fast, wide SCSI-2 device, uses a 68-
pin high density SCSI device connector.
SCSI ID Switch
Used to select the SCSI ID for the DLT drive. Factory
set at 0.
2-8
Description
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Cartridge
The data cartridges used in the DTL7000 Series are housed in
4-inch plastic cases and employ 1/ 2-inch metal particle tape.
Table 2-6 describes and lists the media cartridges that can be
used with the four models.
Table 2-6
Model
Media Cartridge
Drive
Model
Cartridge
Color
Tape
Length
Cartridge Model
4000DLT
7000DLT
DLT4000
DLT7000
DLTTape III
DLTTape IIIXT
DLTTape IV
gray
white
black
1100 feet
1800 feet
1800 feet
DLTTape III
DLTTape IIIXT
DLTTape IV
gray
white
black
1100 feet
1800 feet
1800 feet
The Write-Protect switch prevents accidental erasure of data.
If the switch is moved all the way to the left, the cartridge is
write-protected and the drive cannot write to, or erase data
from, the cartridge. The small orange rectangle will be visible
whenever the cartridge is write-protected. Additionally, an
arrow (beneath the orange rectangle and above the two lines
on the switch), lets you know that data cannot be written to
the cartridge. If the switch is moved all the way to the right,
the cartridge is write-enabled and the drive can write data to,
or erase data from, the cartridge. The orange rectangle will not
be visible whenever the cartridge is write-enabled. On the
right side of the write-protect switch an arrow over one line
indicates that if you slide the switch to the right, data can be
written to the cartridge. Refer to Figure 2-4 on page 2-10.
Description
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
O RANG E
INDICATO R
W RITE-PRO TECT
SW ITCH
W RITE-PRO TECTED
W RITE-ENABLED
Figure 2-4
DLT Data Cartridge
Always remove any cartridge from the drive before turning
off host system power. Failure to remove a cartridge can
result in cartridge and drive damage.
Caution
When you remove the cartridge from the drive, return the
cartridge to its plastic case to prolong the cartridge life.
Other Requirements
SCSI Host Adapter
If your host system does not have an integrated SCSI
controller, a SCSI host adapter must be used to connect the
host computer with the 7000DLT Series. The host adapter you
choose will depend on your system requirements and your
needs.
2-10 Description
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Interface Cable
The kind of cable you need will depend on the kind of SCSI
bus connector on your host adapter. The 7000DLT, a fast, wide
SCSI-2 device, uses a 68-pin high density SCSI device
connector.
Application Software
The software you use will depend upon your storage needs
and the system you are using.
Additional Items
•
At least one data cartridge. See Table 2-7.
Table 2-7
Model
Cartridge Requirements
Required Cartridge
4000DLT
7000DLT
DLTTape IV
DLTTape IV
•
A SCSI bus active terminator.
Other Requirements
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2-12 Description
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety
Safety Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2
Safety
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
3-
Safety Conventions
The following symbols are used throughout the document.
Table 3-1
Hazard Alert Messages
Symbol Damage to ...
Signal Word
Definition
Consequence
Imminent hazardous
electrical situation
Death or serious
injury
Persons
Material
Potential damaging
situation
Possibly damage
to the product or
environment
Caution
Note
Tips for operators
No hazardous or
damaging
consequences
Important or useful
information
No hazardous or
damaging
consequences
The danger exists of a fatal electric shock. At places
designated with this symbol, electrical current can be
present even after switching off the main switch. Before
starting any work, always confirm that all electrical
connections are free of electrical current.
This symbol means that specific regulations, rules, notices,
and working procedures must be observed. Ignoring this
symbol can lead to equipment damage or destruction or to
other property damage.
Caution
This symbol draws attention to user tips. No dangerous or
damaging consequences for personnel or property are
associated with this symbol.
Note
This symbol indicates useful information. No dangerous or
damaging consequences for personnel or property are
associated with this symbol.
Safety Conventions
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
All safety and operating instructions should be read before
this product is operated, and should be retained for future
reference. This unit has been engineered and manufactured
to assure your personal safety. Improper use can result in
potential electrical shock or fire hazards. In order not to
defeat the safeguards, observe the following basic rules for
its installation, use and servicing.
•
•
•
Heed Warnings - All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions - All operating and use instructions
should be followed.
Power Sources - The product should be connected to a
power source only of the type directed in the operating
instructions or as marked on the product.
•
•
Power Cord Protection - The AC line cord should be
routed so that it is not likely to be walked on or pinched
by items placed upon or against it, paying particular
attention to the cord at the wall receptacle, and the point
where the cord exits from the product.
Power Switch - The power switch used in this product
does not disconnect both supply conductors when placed
in the OFF position. To completely disconnect power from
this product, unplug the AC power cord from the
receptacle on the back of the unit.
•
•
Object and Liquid Entry - Care should be taken to insure
that objects do not fall and liquids are not spilled into the
product’s enclosure through openings.
Servicing - The user should not attempt to service the
product beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
Precautions
Do not use oil, solvents, gasoline, paint thinner or insecticides
on the unit.
Do not expose the unit to moisture, to temperatures higher
than 140ºF (60ºC) or to extreme low temperatures.
Keep the unit away from direct sunlight, strong magnetic
fields, excessive dust, humidity and electronic/ electrical
equipment which generates electrical noise.
Hold the AC power plug by the head when removing it from
the AC source outlet; pulling the cord can damage the internal
wires.
3-4
Safety
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the unit on a firm level surface free from vibration, and do
not place anything on top of unit.
Precautions
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6
Safety
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Installation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Unpacking and Inspecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Installing the Host Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Connecting the Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Connecting More than One 4000/ 7000DLT Series . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Setting the SCSI ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Check the SCSI Bus Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Connecting Power and Turning On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Installing the Backup Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2
Installation
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
4-
Overview
This chapter explains the steps necessary to install and test
your 4000/ 7000DLT Series. It also provides an information
symbol for each event that you should verify as correct before
continuing.
Unpacking and Inspecting
Unpack all items from the carton.
None of the components should have any damage.
Save the packing materials in case you need to move or ship
the system in the future. You must ship the unit in the
original or equivalent packing materials or your warranty
may be invalidated.
Installing the Host Adapter
If your host computer does not have native SCSI capability
and the host adapter you are using is not installed, please
install it. Refer to the manual that came with your host adapter
for specific directions.
Connecting the Interface Cable
Attach an interface cable between the host adapter and your
4000/ 7000DLT Series. The kind of cable you need depends on
the kind of SCSI bus connector on your host adapter. The
4000/ 7000DLT Series has two SCSI device connectors on the
rear panel. It does not matter which connector you use.
Note
The bail (or other)
locks at the ends
of the SCSI cable
must be securely
fastened to insure
communications
between the
4000/ 7000DLT
Series and the
host computer.
Make sure that the SCSI cable between the host adapter and
the 4000/7000DLT Series is secure and the connections are
fastened correctly.
Overview
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting More than One 4000/
7000DLT Series
If you are connecting more than one 4000/ 7000DLT Series
unit on the same SCSI channel, simply connect each unit to the
previous unit with an additional interface cable. It doesn't
matter which SCSI connector on each 4000/ 7000DLT Series
unit you connect the interface cable to. Figure 4-1 shows a
sample configuration.
Note
Don’t forget to
install the SCSI
terminator on the
last device in the
chain.
Daisy Chained
Terminator
SCSI ID 3
SCSI ID 2
SCSI
Interface Cables
SCSI ID 1
Host Computer
SCSI ID 0
Figure 4-1
Cable Diagram for 4 4000/ 7000DLT Series Units
4-4
Installation
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the SCSI ID
Depending upon your setup, operating system and number of
Note
The SCSI ID has
been factory
SCSI devices on the bus, you may have to change the SCSI
address of the 4000/ 7000DLT Series. Each device on the bus
must have its own unique address. See Figure 4-1 on page 4-4
and Figure 4-2.
preset to 0.
All devices on a
SCSI bus must be
set to a unique
address.
ꢁ
3
ꢀ
SCSI ID
Switch
Figure 4-2
SCSI ID Switch
The SCSI ID switch is located on the rear of the 4000/ 7000DLT
Series (see Figure 7). Use a small pointed object to press either
the + button on the bottom, or the minus button on the top of
the switch to select the proper ID.
Note
All
4000/ 7000DLT
Series models can
be set to any SCSI
ID between 0 and
7. The 7000DLT, a
fast-wide SCSI-2
device, can be set
to any SCSI ID
between 0 and 15.
Setting the SCSI ID
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Count each device's SCSI ID in sequence 0 to 7 (or 0 to 15),
on each SCSI bus to confirm that no two devices have the
same ID.
Note
The SCSI Host
Adapter is
normally set to
SCSI ID 7, so this
ID is usually not
available for a
device.
Check the SCSI Bus Termination
SCSI buses require termination at each end for proper
operation. A typical external subsystem installation would be
terminated at the SCSI host adapter and at the last device in
the chain.
If an external device is being used with an internal device (on
the same channel), the SCSI host adapter would now be in the
middle of the bus rather than at the end. In this case, the
termination would be at the internal device and the last drive
in the external chain. The terminators on the SCSI host
adapter would be removed. See your SCSI host adapter
manual for directions on removing the terminators on the
board.
Is there a terminator installed on each end of the SCSI bus?
Note
For single-ended
drives,
recommends
using an active
single-ended
SCSI terminator.
For differential
drives, use a
passive
differential
terminator.
4-6
Installation
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Power and Turning On
Step 1
Step 2
Step 3
Plug the power cord into the back of the 4000/
7000DLT Series.
Plug the power cord from the 4000/ 7000DLT Series
into a GROUNDED electrical outlet.
Plug the power cord from your host system into the
same GROUNDED electrical circuit if possible.
Computers and peripherals should always share
the same grounds.
Step 4
Step 5
Turn ON the power to your host system.
Turn the 4000/ 7000DLT Series power ON.
Note
Turning on the
host computer
first ensures that
the SCSI bus
terminators
stabilize the bus
signals before the
tape drive is
turned on.
Installing the Backup Software
At this point, please refer to your backup software installation
guide and install the backup software.
After you have completed installation of your 4000/7000DLT
Series and the backup software, you should run a small
backup/restore and compare to confirm that your unit is
working correctly. See your software installation guide for
additional information.
Connecting Power and Turning On
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4-8
Installation
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Operation and
Maintenance
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Power-on Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Drive Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Drive Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Loading the Data Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Tape in Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Removing the Data Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Cleaning the Tape Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Cleaning the Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2
Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
5-
Overview
This section describes normal operating features of the
4000/ 7000DLT Series. Additionally, it explains how, and
when, to clean the tape head. This section also describes how
to clean the enclosure.
Power-on Self-Test
When you turn system power ON, the DLT drive performs a
Power-on Self-Test (POST). The sequence of events is:
•
The LEDs on the right front panel of the DLT drive will
turn on sequentially from top to bottom. All LEDs will
remain ON for a few seconds.
•
•
The LEDs on the left front panel will turn ON at the same
time for about three seconds and then turn OFF.
The
and
Operate Handle Write Protected
Use Cleaning
LEDs will turn OFF. The
LED will
Tape
Tape in Use
blink while the tape drive initializes.
•
If your external SCSI bus terminator has a Term Power
LED it should also be illuminated.
Overview
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive Status
LED Indicators
After initialization, the drive will be in one of the four states
listed in Table 5-1.
Table 5-1
Drive States Indications
Drive State
LED Indicator Displays and Drive Actions
No cartridge is present.
The
The
LED turns OFF.
Tape in Use
LED turns ON.
Operate Handle
The handle is unlatched.
The drive beeps momentarily.
A cartridge is present and
the handle is down.
The drive loads the cartridge.
When the
LED stops blinking and stays
Tape in Use
ON, the tape’s actual density lights. For example, if
the actual tape density is 2.6, then the LED turns ON
next to the 2.6 label.
When the
LED blinks, you can
Density Override
select a density. The drive is ready for use.
A cartridge is present, but
the handle is up (not
recommended).
The LED turns OFF. The
Handle
When you lower the handle, the cartridge loads.
Tape in Use
LED flashes.
Operate
The drive detects an error
condition.
Then all right or left side LEDs blink repeatedly.
You may try to unload the tape (if present) and
reinitialize the drive by pressing the
button
Unload
or turn power OFF and then ON again. The right or
left side LEDs stop blinking and the drive tries to
reinitialize. The LEDs turn ON steadily again and
then turn OFF if the test succeeds.
5-4
Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Messages
Table 5-2 describes the messages displayed on the LCD
during and immediately after the POST.
Drive Status LCD Messages
Table 5-2
Drive State
LCD Message
POST is executing.
Will be displayed for 3 to 5 seconds, followed by:
DRV F/ W is the firmware version of the drive.
LCD F/ W is the firmware version of the LCD controller.
ID is the SCSI ID setting of the drive.
CPH is the cululative power on hours of the drive.
TSL us the time since last cleaning cycle of the drive (resets
to zero after every cleaning cycle if powered by a power
cycle).
DCL is the drive data cartridge load counter.
POST completed, no cartridge is
present, and the handle is down.
or ‘4000DLT’ (DLT4000)
Note
This is the preferred state for the
4000/ 7000DLT when powering up.
POST completed, a cartridge is
present, but the handle is up
(not recommended).
Note
This message will appear after approximately 5 minutes.
The 4000/ 7000DLT should not be
left in this state when powering
down.
The drive detects an error
condition.
POST completes in about 13 seconds and the drive responds normally to all
commands. However, it may take longer for the media to become ready.
Drive Status
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
POST completes in about 13 seconds and the drive responds normally to all ommands.
However, it may take longer for the media to become ready.
Drive Operating Conditions
LED Indicators
Use Table 5-3 on page 5-6 to determine the drive’s operating
condition.
Table 5-3
Operating Condition Indications
Right Indicator Panel LED
Color State
Label
Operating Condition
Write Protected
Tape in Use
Orange
Yellow
Yellow
ON
OFF
Tape is write-protected.
Tape is write-enabled.
Blinking
ON
Tape is moving.
Tape is loaded; ready for use.
Use Cleaning Tape
ON
Drive head needs cleaning,
or the tape is bad.
Cleaning attempted, but tape
expired, so cleaning not
performed.
Remains on
after unloading
cleaning tape
After cleaning,
turns on again
Problem data cartridge. Try
when reloading another cartridge.
data cartridge
Operate Handle
Green
ON
OK to operate the Cartridge
OFF
Blinking
Insert/ Release Handle.
Do not operate the Cartridge
Insert/ Release Handle.
Drive was powered on with
door open. Close door and
let drive complete
initialization.
All Right Indicator
Panel LEDs or,
All Left Indicator
Panel LEDs
-
ON
Blinking
POST is starting.
An error has occurred.
5-6
Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-3
Operating Condition Indications
Left Indicator Panel LED
Color State
Label
2.6
Operating Condition
Yellow
Yellow
Yellow
ON
Blinking
Tape is recorded in 2.6
format.
Tape is recorded in another
density. You selected this
density for a write from BOT.
6.0
ON
Blinking
Tape is recorded in 6.0
format.
Tape is recorded in another
density. You selected this
density for a write from BOT.
10.0
ON (default)
Blinking
Tape is recorded in 10.0
format.
Tape is recorded in another
density. You selected this
density for a write from BOT.
20.0 (4000/ 7000DLT) Yellow
ON (default)
Blinking
Tape is recorded in 20.0
format.
Tape is recorded in another
density. You selected this
density for a write from BOT.
Compress
Yellow
Yellow
ON
OFF
Compression mode enabled.
(Compression can be done
only in 10.0, 15.0, 20.0, and
70.0 density.)
Compression mode disabled.
Density Override
ON
OFF (default)
Blinking
You selected a density from
the front panel.
Density will be selected by
the host (automatic).
You are in density selection
mode.
All Right Indicator
Panel LEDs, or,
all Left Indicator
Panel LEDs
-
Blinking
A POST error has occurred.
Drive Operating Conditions
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Messages
Table 5-4 on page 5-8 describes the messages displayed by the
LCD during normal operation:
Table 5-4
Drive Operation LCD Messages
Drive Operating
LCD Message
Condition
No tape in drive.
or, ‘4000DLT’ (DLT4000)
When loading or unloading
a tape.
DLTtype = DLT4000 (4000DLT), or DLT7000
(7000DLT).
During the loading process the display may toggle
between “Loading >>>” and “Calibrating>>>”.
Note
While loading the tape, the drive
will enter a false Ready Mode
condition for a short period. During
this false state the Tape In Use LED
will continue to blink. Do not
attempt any operations while the
LED is blinking.
When tape is unloaded.
5-8
Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-4
Drive Operation LCD Messages
When tape is loaded.
DLTtype = DLTTM4000 (4000DLT), or DLTTM7000
(7000DLT).
Compressed if compression mode enabled or
Standard if compression mode disabled.
20/ 40GB = DLTTM4000, 35/ 70GB = DLTTM7000.
This is the normal “Ready Screen”.
If write-protected tape is
inserted
During loading of a write-protected tape, the display
will change from:
“Loading>>>” to “Write Protected Tape Inside
Drive”, the LCD backlight will toggle on/ off and an
audible alarm will sound.
Write-protected tape fully
loaded.
WPT = Write Protected Tape in unit.
WPT will toggle to GB and back to WPT and
continue toggling until next drive action.
Drive Operating Conditions
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-4
Drive Operation LCD Messages
Whenever the system is
writing to a tape, these two
messages will alternate.
Each message will be
displayed for
approximately 2.5 seconds.
DLTtype = DLTTM4000 (4000DLT), or DLTTM7000
(7000DLT).
Compressed if compression mode enabled, standard
if compression mode disabled.
Writing – indicates the system is writing to the tape.
2.1:1 – indicates the current compression ratio being
used.
16GB – indicates the amount of tape still available to
be written to.
3 arrows in motion (
) – indicate tape travel.
Reading – indicates the system is reading from the
tape.
Whenever the system is
reading a tape, this
message will alternate with
the ready screen.
Motion Messages = Loading, Unloading, Reading,
Writing, Positioning, Erasing, Cleaning and
Rewinding.
Whenever a tape is in
motion.
3 arrows (
) – indicate tape travel.
Whenever an incorrect
cartridge type is placed into
a drive.
The LCD will flash and the beeper will sound while
this message is displayed.
Press the Unload button, the drive will begin
unloading the tape and the LCD will return to
normal operation messages.
5-10 Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-4
Drive Operation LCD Messages
The drive head needs
cleaning or the tape is bad.
followed by:
If new tape, or the drive
cannot initialize the tape.
followed by:
followed by:
A hardware error occurs
during normal operation.
Drive Operating Conditions
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Data Cartridge
Due to static the label or other items included in this
package will occasionally cling to the DLT cartridge.
Caution
Before loading into a drive, ensure that all other items from
this package are separated from the cartridge.
Never press in on the hub portion of the data cartridge.
Step 1
If you are planning to write data to, or erase data
from,thecartridge,makesurethe switch
Write-Protect
on the cartridge is in the write-enabled position (all
the way to the right).
A data cartridge can only be loaded when the
Handle
Caution
Operate
LED is ON. Do not attempt to open the
Cartridge
unless this LED is ON steady.
Insert/Release Handle
Step 2
Lift up on the
.
Cartridge Insert/Release Handle
Figure 5-1
Loading a Data Cartridge
5-12 Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
Step 4
Step 5
Insert the data cartridge into the slot.
Push the cartridge into the drive.
Push the Cartridge Insert/Release Handle closed.
The drive will go on-line.
A load sequence will initiate where the Operate Handle
LED will turn OFF and the Tape in Use LED will blink
while the drive moves the tape to BOT (Beginning of Tape).
When the tape is at BOT, the Tape in Use LED will turn ON
steady. Additionally, one of the compression density LEDs
on the Left Indicator Panel may be illuminated or blinking.
The tape is now ready for use.
Data Protection
Caution
The Write-Protect switch on the data cartridge can be
moved while the cartridge is loaded into the drive. The drive
will turn on the Write-Protect LED immediately. However,
if the drive is writing to the tape, write protect does not take
effect until the write operation completes.
Before loading the data cartridge, if you move the
Write-Protect switch to the left, the tape is write-protected;
the Write Protected LED (orange) is ON and data cannot be
written to, or erased from, the tape.
Before loading the data cartridge, if you move the
Write-Protect switch to the right, the tape is write-enabled
and data can be written to, or erased from, the tape (if it is not
software write-protected).
After loading the data cartridge and during operation, if you
move the Write-Protect switch from the write-protected
position (to the left) to the write-enabled position (to the
right), the tape becomes write-enabled after a variable amount
of time (seconds).
After loading the data cartridge and during operation, if you
move the Write-Protect switch from the write-enabled
position (to the right) to the write-protected position (to the
left), the tape becomes write-protected after a variable amount
of time (seconds).
Tape in Use
Whenever the Tape in Use LED (yellow) is ON steady, the
tape is ready to use. When the tape is being read, written, or
rewound, Tape in Use blinks.
Data Protection
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-5 indicates what is happening during cartridge use:
Tape in Use Indications
(Right Indicator Panel)
Table 5-5
LED
State
ON steady
Blinks irregularly
Blinks regularly
Meaning
Tape in Use
A cartridge is loaded, but the tape is not
moving. This can mean no application is
communicating with the controller, or that
the application is communicating but is not
delivering commands for tape motion.
A read or write is in progress.
Tape is loading, unloading, or rewinding.
Operate
Handle
ON and beeper
sounds
Tape is unloaded into the cartridge and the
cartridge can now be removed, or if the
drive is unloaded, a cartridge can now be
inserted.
All LEDs
Blinking
An error has occurred during operation.
Removing the Data Cartridge
Remove a cartridge from the drive before turning OFF host
Caution
system power. Failure to remove a cartridge before turning
OFF host system power can result in cartridge and drive
damage.
To unload a cartridge from the drive perform the following
steps
Step 1
The
Push the
button.
Unload
LED will blink as the tape rewinds.
Tape in Use
A data cartridge can only be unloaded when the
Caution
Operate
LED is ON. Do not attempt to open the
Handle
Cartridge
unless this LED is ON steady.
Insert/Release Handle
Step 2
Step 3
When the
LED is ON (and the
Cartridge
open to eject the cartridge
Operate Handle
beeper has sounded), pull the
Insert/Release Handle
from the drive.
Remove the cartridge.
5-14 Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4
Push the Cartridge Insert/Release Handle closed.
Caution
When you remove the cartridge from the drive, return the
cartridge to its plastic case to prolong the cartridge life.
Cleaning the Tape Head
The 4000/ 7000DLT Series is a highly sophisticated unit. No
routine maintenance is required apart from periodically
cleaning the drive head whenever the Use Cleaning Tape
LED is illuminated and the LCD displays the following
message:
followed by
If your 4000/ 7000DLT Series fails to operate correctly,
immediately call the customer service.
Cleaning the head should always be performed as the first
step if the Use Cleaning Tape LED illuminates and the LCD
displays the above message.
Table 5-6 on page 5-16 tells you when to use the cleaning tape.
Cleaning the Tape Head
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-6
Using the Cleaning Tape
If . . .
It means . . .
You should . . .
While using a data
cartridge, the
Cleaning Tape
illuminates and the front
panel LCD displays:
The drive head needs
cleaning or the tape is
bad
Use the cleaning cartridge.
Load the cleaning
cartridge according to
Loading the Data Cartridge
on page 5-12.
Use
LED
When cleaning is
complete, the beeper will
sound alerting you to
remove the cleaning
cartridge. Remove the
cleaning cartridge from the
drive according to
and:
RemovingtheDataCartridge
on page 5-14
While using a data
The data cartridge may
be damaged
Back up the data from this
cartridge onto another
cartridge, it may be
cartridge, the
Use
LED
Cleaning Tape
begins to blink and the
front panel LCD
displays:
damaged. A damaged
cartridge may cause
unnecessary use of the
cleaning cartridge.
and
LED Your data cartridge may
Try another data cartridge.
Use Cleaning Tape
still illuminates after you
clean the drive head.
be causing the problem
LED Cleaning has not been
accomplished and the
cleaning cartridge has no
remaining cycles
Replace the cleaning
cartridge.
Use Cleaning Tape
illuminates after you
load the cleaning
cartridge
available.
Using cloth swabs, cotton swabs, cleaning agents, or
unapproved cleaning cartridges will void your warranty.
Use only an approved cleaning cartridge.
Caution
5-16 Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
To clean the head, use a cleaning cartridge. Inert the cleaning
cartridge in the drive as described in Loading the Data Cartridge
on page 5-12. The drive will automatically clean the head.
When the cleaning operation is complete, the beeper will
sound alerting you to remove the cleaning cartridge. The
following messages will be displayed during the cleaning
process.
Table 5-7
Cleaning Cycle LCD Messages
When tape is loaded.
DLTtype = DLTTM4000 (4000DLT), or DLTTM7000
(7000DLT).
Compressed if compression mode enabled or
Standard if compression mode disabled.
20/ 40GB = DLT4000, 35/ 70GB = DLT7000.
This is the normal “Ready Screen”.
While loading the cleaning
tape.
DLTtype = DLTTM4000 (4000DLT), or DLTTM7000
(7000DLT).
While the cleaning cycle is
executing.
When cleaning cycle is
completed.
When the cleaning process is complete, the LCD will
display the following for 3 to 5 seconds:
CCL ia the Cleaning Cartridge Load Counter and
equals the number of timews that6 a cleaning
cartridge has been loaded in this drive.
CCA is the cumulative number of times this cleaning
cartridge has been used to clean a drive.
Cleaning the Tape Head
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-7
Cleaning Cycle LCD Messages
When cleaning tape is
unloaded.
Do not remove the cleaning cartridge before the drive
sounds the beeper.
Caution
Remove the cleaning cartridge from the drive as described in
Removing the Data Cartridge on page 5-14.
If you load the cleaning cartridge into the drive after it has
exhausted its cleaning cycles, it will not clean the head (the
cycle is noticeably shorter) and the Use Cleaning Tape LED
will be illuminated. Be sure to replace the cleaning cartridge
when the cleaning cycle is noticeably shorter.
Cleaning the Enclosure
The outside of the enclosure can be cleaned with a damp
towel. If you use a liquid all-purpose cleaner, apply it to the
towel. Do not spray the enclosure.
5-18 Operation and Maintenance
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Troubleshooting
and Diagnostic
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Use Cleaning Tape LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Why the Use Cleaning Tape LED Gets Turned ON . . . . . . . . . . . . . . . . . . . . . . . . 7-6
High Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2
Troubleshooting and Diagnostic
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
6-
Overview
This section lists a number of common problems and the
actions to take to correct them. It provides information on why
the DLT drive turns on the Use Cleaning Tape LED. The
section also explains what to do when you need technical
support.
Troubleshooting Chart
If the 4000/ 7000DLT Series fails during POST or operation,
use the following table to determine the problem and the
action to take:
Table 6-1
Problem Chart
If . . .
Then . . .
You should . . .
Your system does not
recognize the
Your system might not be Configure your system to
configured to see the see the ID.
4000/ 7000DLT Series unit SCSI ID
The SCSI ID might not be Change the SCSI ID and
unique
reconfigure the system.
The new ID is effective at
the next power-on.
The parameters for your
SCSI adapter may be
incorrect
Check your SCSI adapter
installation.
The SCSI signal cable
may be loose
Make sure the connector on
each end of the cable is
fully seated and the bail
locks are secure.
The SCSI terminator may
not be present or might
be loose
Install the terminator;
make sure the terminator is
fully seated and the bail
locks are secure.
Overview
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1
Problem Chart
Your system does not
recognize the
4000/ 7000DLT Series unit
(Continued)
The SCSI bus may not be
correctly terminated
If the 4000/ 7000DLT Series
unit is the last or only
device on the bus, make
sure the terminator is
installed on the
4000/ 7000DLT.
If the 4000/ 7000DLT Series
unit is not the last or only
device on the bus, check
the cable connections and
make sure the terminator is
installed at the end of the
bus.
The SCSI terminator may
not be at the end of the
bus, or more than two
terminators may be
present
Be sure to install a
terminator at each end of
the bus. One terminator is
usually installed at the host
system.
The SCSI bus might be
too long.
Limit the bus length to the
ANSI SCSI-2 standard of 6
meters (19 feet) for single
ended buses [3 meters for
the 7000DLT].
Too many devices might
be on the bus
Limit the number of
devices on the bus
(including the host system)
to eight.
Check your system
configuration rules.
The 4000/ 7000DLT Series The 4000/ 7000DLT Series Check the 4000/ 7000 Series
unit does not power up
unit has no power
unit power cord
connections with the 4000/
7000DLT Series unit power
switch OFF.
6-4
Troubleshooting and Diagnostic
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1
Problem Chart
All right or all left
indicator panel LEDs on
the drive front panel
blink
A drive fault has
occurred
Try to unload the tape and
reinitialize the drive by
pressing the Unload button
or turn the 4000/ 7000DLT
Series unit power off and
then on again.
The LEDs will stop
blinking and the drive will
try to reinitialize. The LEDs
will turn on steady again
and go off if the test
succeeds.
You are finding fatal or
nonfatal errors for which
The bus termination or
SCSI signal cable
Make sure the SCSI bus is
terminated.
you cannot determine the connections might be
cause
incorrect
The AC power source
grounding might be
incorrect
Use an AC outlet for the
4000/ 7000 Series unit on
the same AC circuit as the
AC line powering the host
system.
Use Cleaning Tape LED
If an excessive number of read-after-write errors are detected
during normal operation of the 4000/ 7000DLT Series, the
Use
LED will be turned on by the drive.
Cleaning Tape
Usually, the
LED is turned on by the
Use Cleaning Tape
drive because of a dirty head, so the head should be cleaned
and the operation tried again.
If the
LED is again turned on and this
Use Cleaning Tape
seems to be a cartridge rather than a drive problem, make sure
that all the data on that cartridge is backed up to a new
cartridge by doing a complete backup from the source drive,
if necessary. Then discard the old cartridge. If you are unsure
of the problem source, call customer service.
The
LED is normally turned off by
Use Cleaning Tape
executing a cleaning cycle or by cycling power to the
4000/ 7000DLT Series.
Use Cleaning Tape LED
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Why the Use Cleaning Tape LED Gets
Turned ON
The
LED will be turned on whenever the
Use Cleaning Tape
drive has determined that low level error performance has
degraded to a point where drive head cleaning is absolutely
required. It does this by counting the number of C3 (soft)
errors as well as the RAW (Read After Write) errors over a
number of Mbytes. When a predetermined error rate
threshold is reached, the drive displays the warning. Some
drives display the warning after a specified number of hours
of tape motion have been logged. When a tape is loaded, it
may take several minutes for the indication to come on
because the drive will wait for a specific number of bytes to be
written. A hard (non-recoverable) error will cause the
warning to be displayed immediately.
The most common reasons that the
LED
Use Cleaning Tape
gets turned on for, in order of highest rate of occurrence, are
listed below:
•
•
Dirty ("Stained") heads.
A cleaning cycle must be executed to clear this indication.
Worn tape.
DLT tapes are rated at 500,000 passes. Applications that
overwrite small blocks of data cause "shoe shining" of the
tape against the head and will reach the 500,000 passes
sooner than might be expected.
•
Bad environment.
Data errors result from a number of factors, each of which
subtract from the margin between good data recovery
and an error. Electrical or magnetic interference can
decrease this margin. High levels of dust contamination,
high humidity, and heat can also be significant factors.
Placing a CRT monitor on top of, or directly next to, a
4000/7000DLT Series should always be avoided.
•
Worn heads.
The tape heads will eventually wear out causing the time
between cleanings to get shorter and shorter. Tape head
failure is usually predicted at about 12% of the MTBF
rating (10,000 hours).
•
Defective drive.
Drive amplifier settings could be off, causing error rate
degradation. The drive could simply have failed.
6-6
Troubleshooting and Diagnostic
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
High Humidity
To minimize the chance of condensation, please observe the
following guidelines:
•
If you expose cartridges to temperatures outside the
operating limits (5-40°C/ 40-113°F), stabilize them before
you use them. To do this, leave the cartridges in the
operating temperature for a minimum of two hours.
•
Avoid temperature problems by ensuring that the
ventilator slots at the front of the drive and the grille on
the bottom of the chassis are not obstructed so that the
drive has adequate ventilation
•
•
•
Position the drive where the temperature is relatively
stable, for example, away from open windows, fan
heaters, and doors.
Avoid leaving cartridges in severe temperature
conditions, for example, in a car standing in bright
sunlight.
Avoid transferring data (reading from and writing to
cartridges) when the temperature is changing by more
than 10°C per hour.
High Humidity
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8
Troubleshooting and Diagnostic
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Specification
General Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
Specification
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
A-
General Specification
This section contains specification information on the
4000/ 7000DLT Series. See Table A-1.
Table A-1
Specifications
Drive
Type:
Quantum® DLT™4000
Quantum® DLT™7000
4000DLT
7000DLT
Data Transfer Rate
(compressed mode):
180 MB/ min.
600 MB/ min.
4000DLT
7000DLT
Enclosure
Electrical Interface:
Physical Interface
SCSI-2
SCSI-2 Fast, Wide
4000DLT
7000DLT
50-pin, shielded, low-density device connector
68-pin, shielded, high-density device connector
Reliability
Maintenance
Periodic cleaning of drive head using DLT cleaning
cartridge.
MTBF:
MTTR:
More than 80,000 power-on hours
Within 30 minutes (drive replacement)
Physical
Dimensions:
Weight:
5.75"(h) x 10.50" (w) x 14.50" (d)
14 lbs.
Environment
Electrical:
100-240 vac, 50-60 Hz, 0.6 - 0.3A
less than 40 watts
Power Consumption
BTU/ Hour:
:
170 to 205
Environment (continued)
Temperature
5 ° C to 10° C (Operating)
-40° C to 66° C (Storage/ Shipping)
:
Humidity
20% to 80% (Operating)
:
10% to 95% (Storage/ Shipping)
General Specification
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
0.25G (5-500 Hz) (Operating)
Table A-1
Vibration:
0.5G (5-500 Hz) (Storage/ Shipping)
Shock:
2G Operating
30G Storage/ Shipping
A-4
Specification
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Drive
Configuration
Drive Dependent Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
SCSI Bus Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
DLT4000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
DLT7000 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4
SCSI Bus Termination and Terminator Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
DLT4000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5
DLT7000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2
Drive Configuration
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
B-
Drive Dependent Configuration
This section describes the options you can select by installing
jumpers on the DLT Tape Drives.
SCSI Bus Parity
The following paragraphs detail information about parity
selection on different drive types.
DLT4000 Drives
If your host computer system does not generate SCSI bus
parity, you can disable parity checking in the DLT drives by
installing a jumper over two pins on the SCSI ID connector.
See Figure B-1 for location of the connector.
Front
Bezel
Left Side
SCSI ID
Connector
Figure B-1
DLT4000 Tape Drive Connectors (Left Side)
Figure B-2 shows which pins of the SCSI ID connector have to
be jumpered to disable parity.
Disable
Parity
Figure B-2
Disable Parity Pins on SCSI ID Connector
Drive Dependent Configuration
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
DLT7000 Drive
If your host computer system does not generate SCSI bus
parity, you can disable parity checking in the DLT7000 drive
by installing a jumper over two pins on the DFDT connector.
See Figure B-3 for location of the connector.
Front
Bezel
TRM PWR Connector
Right Side
DFDT Connector
Figure B-3
DLT7000 Tape Drive Connectors (Right Side)
Figure B-4 shows which pins of the DFDT connector have to
be jumpered to disable parity.
Disable
Parity
Figure B-4
Disable Parity Pins on DFDT Connector
B-4
Drive Configuration
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Bus Termination and Terminator
Power
The following paragraphs describe information about
termination selection on different drives.
Note
The SCSI bus
must be
terminated at
both ends, and at
least one device
must supply
terminator
power.
DLT4000 Drives
The DLT4000 drives can be configured to supply terminator
power and termination on the bus, by jumpering specific pins
on the TRM PWR/ TRM ENB connector. See Figure B-5 for the
location of the TRM PWR/ TRM ENB connector).
Front
Bezel
TRM PWR/TRM ENB
Right Side
Figure B-5
DLT4000 Tape Drive Connectors (right side)
Figure 14 and the table following it illustrate the possible
position(s) for the TRM PWR/ TRM ENB jumper(s).
If an external SCSI terminator is used, configurations 2 and
4 in Figure B-6 on page B-6 cannot be used.
Caution
SCSI Bus Termination and Terminator Power
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
No Term Power
Disable Active Termination
Term Power
Disable Active Termination
1
3
No Term Power
Enable Active Termination
Term Power
Enable Active Termination
2
4
Figure B-6
TRM PWR/ TRM ENB Jumper Position
If . . .
And . . .
Then You Should . . .
Another device is
providing
terminator power
The 4000/ 7000DLT
Series is not at the
end of the SCSI bus
chain
Connect jumpers as 1 in Figure B-6.
Connect jumpers as 2 in Figure B-6.
Connect jumpers as 3 in Figure B-6.
Connect jumpers as 4 in Figure B-6.
Another device is
providing
terminator power
The 4000/ 7000DLT
Series is at the end
of the SCSI bus
chain
No other device on
the SCSI bus is
providing
The 4000/ 7000DLT
Series is not at the
end of the SCSI bus
chain
terminator power
No other device on
the SCSI bus is
providing
The 4000/ 7000DLT
Series is at the end
of the SCSI bus
chain
terminator power
B-6
Drive Configuration
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
DLT7000 Drives
The DLT7000 drive can be configured to supply terminator
power, by jumpering specific pins on the TRM PWR
connector. See Figure B-7 and Figure B-8 for the location of the
TRM PWR connector.
Front
Bezel
TRM PWR Connector
Right Side
DFDT Connector
Figure B-7
DLT7000 Tape Drive Connectors (right side)
TERMPOWER
Figure B-8
Term Power Pins on TRM PWR Connector
SCSI Bus Termination and Terminator Power
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
B-8
Drive Configuration
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
C
Regulatory
Notices
FCC Notices (U.S. Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Shielded Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Product Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
IC Notice (Canada Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
EN 55022 Compliance (Czech Republic Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
CE Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
VCCI Notices (Japan Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Download from Www.Somanuals.com. All Manuals Search And Download.
C-2
Regulatory Notices
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
C-
FCC Notices (U.S. Only)
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the manufacturer's instruction manual, may cause
interference with radio and television reception. This
equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment
does cause harmful interference with radio or television
reception, which can be determined by turning the equipment
off and on, you are encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
•
Reorient the receiving antenna.
Relocate the computer with respect to the receiver.
Move the computer away from the receiver.
Plug the computer into a different outlet so that the
computer and the receiver are on different branch circuits.
If necessary, consult an experienced radio/ television
technician for additional suggestions. You may find the
following booklet helpful:
•
FCC Interference Handbook, 1986, available from the U.S.
Government Printing Office, Washington, DC 20402,
Stock No. 004-000-00450-7.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
•
•
This device may not cause harmful interference.
This device must accept any interference received,
including interference that may cause undesired
operation.
Shielded Cables
Use only shielded cables for connecting peripherals to this
device to reduce the possibility of interference with radio and
television reception. Using shielded cables ensures that you
maintain the appropriate FCC radio frequency emissions
compliance (for a Class A device) or FCC certification (for a
Class B device) of this product.
FCC Notices (U.S. Only)
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Type
The following information is provided on the device or
devices covered in this document in compliance with FCC
regulations:
Product Name
Model number
4000/ 7000DLT Tabletop Unit
TBD
Company name Advanced Digital Information
Corporation, PO Box 97057, Redmond, WA
98073-9757 USA
Phone number
(425) 881-8004
IC Notice (Canada Only)
Most tape libraries are classified by the Industry Canada (IC)
Interference-Causing Equipment Standard #3 (ICES-003) as
Class B digital devices. To determine which classification
(Class A or B) applies to your tape library, examine all
registration labels located on the bottom or the back panel of
your library. A statement in the form of "IC Class A ICES-3" or
"IC Class B ICES-3" will be located on one of these labels.
Note that Industry Canada regulations provide that changes
or modifications not expressly approved by the tape library
manufacturer could void your authority to operate this
equipment.
This Class B (or Class A, if so indicated on the registration
label) digital apparatus meets the requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la Classe B (ou Classe A, si ainsi
indiqué sur l'étiquette d'enreg-istration) respecte toutes les
exigences du Reglement sur le Materiel Brouilleur du Canada.
C-4
Regulatory Notices
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
EN 55022 Compliance (Czech Republic
Only)
This device belongs to category B devices as described in EN
55022, unless it is specifically stated that it is a category A
device on the specification label. The following applies to
devices in category A of EN 55022 (radius of protection up to
30 meters). The user of the device is obliged to take all steps
necessary to remove sources of interference to telecom-
munication or other devices.
Pokud nenÌ na typovÈm ötitku poËÌtaËe uvedeno, ûe spad·
do t¯Ìdy A podle EN 55022, spad· automaticky do t¯Ìdy B
podle EN 55022. Pro za¯ÌzenÌ za¯azen· do t¯Ìdy A (ochrannÈ
p·smo 30m) podle EN 55022 platÌ n·sledujÌcÌ. Dojde-li k
ruöenÌ telekomunikaËnÌch nebo jinych za¯ÌzenÌ, je uûivatel
povinen provÈst takov· opat¯enÌ, aby ruöenÌ odstranil.
CE Notice
Marking by the symbol indicates compliance of this tape
library to the EMC (Electro-magnetic Compatibility) directive
of the European Community. Such marking is indicative that
this tape library meets or exceeds the following technical
standards:
EN 55022
"Limits and Methods of Measurement of
Radio Interference Characteristics of
Information Technology Equipment." This
system is an EN 55022 Class B device.
EN 50082-1:1997 "Electromagnetic compatibility-
Genericimmunity standard Part 1: Res-
idential, commercial, and light industry."
EN 61000-4-2
"Electromagnetic compatibility for
industrial-process measurement and
control equipment Part 2: Electrostatic
discharge requirements." - Severity level 3.
IEC 801-3
"Electromagnetic compatibility for
industrial-process measurement and
control equipment Part 3: Radiated
electromagnetic field requirements." -
Severity level 2.
EN 55022 Compliance (Czech Republic Only)
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
EN 61000-4-4
"Electromagnetic compatibility for
industrial-process measurement and
control equipment Part 4: Electrical fast
transient/ burst requirements." - Severity
level 2.
EN60950:1992 + Amd.1:1993 + Amd.2:1993 with
considerations to Amd.3:1995
"Safety of Information Technology
Equipment including Electrical Business
Equipment."
A "Declaration of Conformity" in accordance with the
preceding standards has been made and is on file at ADIC
Europe, Z.A. du Bel-Air, 21 avenue Saint-Fiacre, F78100 -
Saint-Germain en Laye, FRANCE.
VCCI Notices (Japan Only)
This is a Class B product based on the standard of the
Voluntary Control Council for Interfer-ence for information
technology equipment. If this equipment is used near a radio
or television receiver in a domestic environment, it may cause
radio interference. Install and use the equip-ment according
to the instruction manual.
Note that VCCI regulations provide that changes or
modifications not expressly approved by the tape library
manufacturer could void your authority to operate this
equipment.
C-6
Regulatory Notices
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
5-13, . . . . . . . . . . . . . . . . . . . . . .5-14, 5-15
cartridge insert/ release handle . . . . . . . .2-7, 2-8
Chapter Organization . . . . . . . . . . . . . . . . . . . .1-3
cleaning cartridge . . . . . . . . . . . . . 5-16, 5-17, A-3
cleaning the drive head . . . . . . . . . . . . . . . . . .5-15
cleaning the enclosure . . . . . . . . . . . . . . . . . . .5-17
Cleaning the Tape Head . . . . . . . . . . . . . . . . .5-15
Compress LED . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Compression mode . . . . . . . . . . . . . . . . . . . . . . .2-8
Compression mode disabled . . . . . . . . . . . . . .5-7
compression mode disabled . . . . . . . . . . . . . . .5-9
Compression mode enabled . . . . . . . . . . . . . . .5-7
compression mode enabled . . . . . . . . . . . . . . . .5-9
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
customer assistance . . . . . . . . . . . . . . . . . . . . . .7-5
- 1 -
10.0 format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
10.0 GB format . . . . . . . . . . . . . . . . . . . . . . 2-4, 2-8
- 2 -
2.6 format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
2.6 GB format . . . . . . . . . . . . . . . . . . . . . . . 2-4, 2-8
20.0 format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
20.0 GB format . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
- 6 -
6.0 format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
6.0 GB format . . . . . . . . . . . . . . . . . . . . . . . 2-4, 2-8
- 7 -
- D -
70.0 GB format . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
data capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Data cartridge . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
data cartridge 2-10, 2-11, 5-11, 5-12, 5-13, 5-16, B-5
data compaction . . . . . . . . . . . . . . . . . . . . . . . . .2-3
data compression . . . . . . . . . . . . . . . . . . . . . . . .2-3
data transfer rate . . . . . . . . . . . . . . . . . . . . . . . . A-3
Density Override LED . . . . . . . . . . . . . . . .2-8, 5-4
Density Select 10.0 LED . . . . . . . . . . . . . . . . . . .2-8
Density Select 2.6 LED . . . . . . . . . . . . . . . . . . . .2-8
Density Select 20.0 LED . . . . . . . . . . . . . . . . . . .2-8
Density Select 6.0 LED . . . . . . . . . . . . . . . . . . . .2-8
Density Select 70.0 LED . . . . . . . . . . . . . . . . . . .2-8
density selection mode . . . . . . . . . . . . . . .2-8, 5-7
diagnostic results . . . . . . . . . . . . . . . . . . . . . . . .2-5
Digital Linear Tape . . . . . . . . . . . . . . . . . . . . . . .2-3
dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
- A -
AC Power Connector . . . . . . . . . . . . . . . . . . . . . 2-9
Application Software . . . . . . . . . . . . . . . . . . . . 2-12
archiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Associated Documents . . . . . . . . . . . . . . . . . . . 1-4
- B -
backup software . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
bail locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3, 7-3
Beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
- C -
Cartridge Insert/ Release Handle 2-8, 5-6, 5-12,
Download from Www.Somanuals.com. All Manuals Search And Download.
disable parity . . . . . . . . . . . . . . . . . . . . . . .B-3, B-4
drive error messages . . . . . . . . . . . . . . . . . . . . . 2-7
Drive head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
drive head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
drive operating condition . . . . . . . . . . . . . . . . . 5-5
Drive Operating Conditions . . . . . . . . . . . . . . . 5-5
drive operating status . . . . . . . . . . . . . . . . . . . . 2-5
drive POST results . . . . . . . . . . . . . . . . . . . . . . . 2-7
drive Power-On Self-Test (POST) . . . . . . . . . . 2-3
Drive Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
drive status messages . . . . . . . . . . . . . . . . 2-3, 2-7
drive type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Motion Messages . . . . . . . . . . . . . . . . . . . . . . .5-10
- O -
off-line storage . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
off-site data storage . . . . . . . . . . . . . . . . . . . . . .2-4
Operate Handle LED 2-7, 2-8, 5-3, 5-4, 5-6, 5-12,
5-13, . . . . . . . . . . . . . . . . . . . . . . . . . . .5-14
Organization
Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
- P -
packing materials . . . . . . . . . . . . . . . . . . . . . . . .4-3
physical attributes . . . . . . . . . . . . . . . . . . . . . . A-3
POST . . . . . . . . . . . . . . .5-3, 5-4, 5-5, 5-6, 5-7, 7-3
power consumption . . . . . . . . . . . . . . . . . . . . . A-3
Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
power switch . . . . . . . . . . . . . . . . . . . . . . . .2-9, 7-4
Power-on Self-Test . . . . . . . . . . . . . . . . . . . . . . .5-3
- E -
electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
electrical interference . . . . . . . . . . . . . . . . . . . . . 7-6
embedded data logging of errors . . . . . . . . . . 2-5
embedded diagnostic software . . . . . . . . . . . . 2-5
environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
environmental attributes . . . . . . . . . . . . . . . . A-3
error messages . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
- R -
Ready Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8, 4-3
reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Removing the Data Cartridge . . . . . . . . . . . . .5-14
- F -
firmware updates . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Flash EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
front panel . . . . . . . . . . 2-4, 2-5, 2-8, 5-3, 5-7, 7-5
- S -
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . .3-3
SCSI adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
SCSI address . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
SCSI bus . . . . . . . . . . . 4-6, 4-7, 7-4, 7-5, B-5, B-6
SCSI bus chain . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
SCSI bus connector . . . . . . . . . . . . . . . . . .2-12, 4-3
SCSI Bus Parity . . . . . . . . . . . . . . . . . . . . . . . . . B-3
SCSI bus parity . . . . . . . . . . . . . . . . . . . . . B-3, B-4
SCSI Bus Termination . . . . . . . . . . . . . . . . . . . .4-6
SCSI Bus Termination and Terminator Power B-5
SCSI cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
SCSI channel . . . . . . . . . . . . . . . . . . . . . . . .2-9, 4-4
SCSI Channel Connectors . . . . . . . . . . . . . . . . .2-9
SCSI connector . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
SCSI controller . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
SCSI device connectors . . . . . . . . . . . . . . . . . . .4-3
SCSI devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
SCSI Host Adapter . . . . . . . . . . . . . . . . . . . . . . .4-6
SCSI host adapter . . . . . . . . . . . . . .2-11, 2-12, 4-6
SCSI ID . . . . . . . . . . . . . . . . . . . . .2-9, 4-5, 4-6, 7-3
SCSI ID connector . . . . . . . . . . . . . . . . . . . B-3, B-4
SCSI ID Switch . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
- H -
hardware error . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
head cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
host adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
host computer . . . . . .2-9, 2-11, 4-3, 4-7, B-3, B-4
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7, A-4
humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
- I -
Intended Audience . . . . . . . . . . . . . . . . . . . . . . 1-3
interchange compatibility . . . . . . . . . . . . . . . . . 2-4
interface cable . . . . . . . . . . . . . . . . . . . 2-9, 4-3, 4-4
- M -
magnetic interference . . . . . . . . . . . . . . . . . . . . 7-6
maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Mean Time Between Failures . . . . . . . . . 7-6, A-3
Mean Time To Repair . . . . . . . . . . . . . . . . . . . A-3
media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4, 5-5
in-8 Index
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI ID switch . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
SCSI Interface Cable . . . . . . . . . . . . . . . . . . . . 2-12
SCSI interface cable . . . . . . . . . . . . . . . . . . . . . . 4-3
SCSI signal cable . . . . . . . . . . . . . . . . . . . . . . . . 7-3
SCSI terminator . . . . 2-12, 4-4, 4-6, 5-3, 7-3, 7-4
shelf life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Symbols and Notes . . . . . . . . . . . . . . . . . . . . . . 1-4
system configuration . . . . . . . . . . . . . . . . . . . . . 7-4
- T -
Tape density . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Tape In Use LED . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Tape in Use LED . . 2-7, 5-3, 5-4, 5-6, 5-13, 5-14
temperature . . . . . . . . . . . . . . . . . . . . . . . 7-7, A-3
temperature problems . . . . . . . . . . . . . . . . . . . . 7-7
term power . . . . . . . . . . . . . . . . . . . . B-5, B-6, B-7
terminator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
- U -
Unload Button . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Unload button . . . . . . . . . . . . . . . . . 5-4, 5-14, 7-5
Use Cleaning Tape LED 2-7, 5-3, 5-6, 5-15, 5-16,
5-17, . . . . . . . . . . . . . . . . . . . . . . . . 7-5, 7-6
- V -
ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
- W -
warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3, 5-16
weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
write enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Write Protected LED . . . . . . . . 2-7, 5-3, 5-6, 5-13
write-enabled . . . . . . . . . . . . 2-10, 5-6, 5-12, 5-13
Write-Protect switch . . . . . . . . . . 2-10, 5-12, 5-13
write-protected . . . . . . . . 2-7, 2-10, 5-6, 5-9, 5-13
Index
in-9
Download from Www.Somanuals.com. All Manuals Search And Download.
in-10 Index
62-0162-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|