ASA Electronics TV/VCP Floor Console
Model K-9 With out Harness and Antenna
12 Volt DC powered remote controlled 9” television AVT-975
12 Volt DC powered remote controlled VHS Video Cassette Player AVP-7000
Installation Instructions
Audiovox Specialized Applications, LLC
23319 Cooper Drive
Elkhart IN 46514
1 (219) 264-3135
Page 1 of 10
P/N 8007132
REV. B BJ
Download from Www.Somanuals.com. All Manuals Search And Download.
There are six (6) steps to install the K-9 TV/VCP floor console:
Step # 1
Step # 2
Step # 3
Step # 4
Step # 5
Step # 6
Remove face of the console
Install brackets and the straps
Install console to the floor of the vehicle
Install VCP
Install TV
Replace console face
STEP #1 REMOVE THE FACE OF THE CONSOLE
Þ Remove 4 Phillips screws securing face of console to body of console.
Þ Set screws and face aside. Take care that screws do not get lost.
1) Disassemble shroud.
P/N 8007132
Page 3 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Step #2 Install brackets and straps
1) Mount brackets using four screws. Do not use center hole.
2) Use soldering iron, if necessary, to melt holes in open strap, as shown.
3) Use soldering iron, if necessary, to melt holes in closed strap, as shown.
P/N 8007132
Page 4 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Pre-drill 1/8” pilot holes on bottom TV shelf for strap.
P/N 8007132
Page 5 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
1) Attach both straps and customer-supplied harness, securing harness as needed.
P/N 8007132
Page 6 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Step #3 INSTALL CONSOLE TO FLOOR OF VEHICLE
Þ BEFORE DRILLING ANY HOLES VERIFY THAT DRILL BIT WILL NOT ENTER
INTO FRAME RAIL(S) OF VEHICLE, ELECTRICAL WIRES, FUEL LINES,
BRAKE LINES, HOSES, EXHAUST SYSTEMS OR ANY OTHER ITEMS THAT
WILL IMPAIR OPERATION OF VEHICLE. THE BOLTS OF THE FLOOR
CONSOLE MUST SECURE TO FLOOR PANEL OF VEHICLE. CLIMB UNDER
VEHICLE AND LOOK TO VERIFY THAT HOLES WILL BE IN PROPER
LOCATIONS.
Þ Set console on floor of vehicle and mark where holes are to be drilled. Drill
small 1/8” pilot holes to verify that drill holes are in proper locations.
Þ After verifying that 1/8” pilot holes are in proper locations, use ¼” drill bit to
enlarge 1/8” pilot holes.
Þ Set console on floor over holes.
Þ Place bolts through feet of console and into holes previously drilled.
Þ Place one large fender washer over each of bolts and attach nuts.
Þ Tighten nuts down securely. Have second person inside vehicle hold bolts
securely with box-end wrench while person underneath vehicle tightens down
nuts.
P/N 8007132
Page 7 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP #4 INSTALL VCP INTO CONSOLE
Þ Remove VCP from box.
Þ Connect white RCA connector (customer supplied) from console wiring harness
to white audio output jack of VCP.
Þ Connect yellow RCA connector (customer supplied) from console wiring harness
to yellow audio output jack of VCP.
Þ Connect DC power connector (customer supplied) from console to DC power
jack of VCP.
Þ Slide VCP into slot in front of console.
P/N 8007132
Page 8 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP #5 INSTALL TV INTO CONSOLE
Þ Connect yellow RCA connector (customer supplied) to yellow RCA input jack on
rear of television. This is the video connection.
Þ Connect white RCA connector (customer supplied) to white RCA input jack on
rear of television. This is the audio connection.
Þ Connect DC power connector (customer supplied) to rear of television.
Þ Connect coaxial cable antenna “F” connector (customer supplied)to rear of
television “ANT” input.
Þ Place television on shelf of console.
Þ Secure television down with two straps. Make absolutely certain that straps are
tight.
P/N 8007132
Page 9 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP #6 REPLACE THE FACE OF THE CONSOLE
Þ Place face of console over body of console. Gently tap into place.
Þ Install four Phillips screws that hold the face to the body.
P/N 8007132
Page 10 of 10
Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
|