PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
PRELIMINARY
Directions For Use
PRF227S
PLW225S
P
3135-125-20871
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
INTRODUCTION
Philips Institutional TV Software
Your Philips Institutional Television can be configured to operate in either "Consumer" or "Commercial" operational
modes.
Commercial Mode: Your Philips Institutional Television is configured at the Factory to operate in Commercial mode.
When the television is in Commercial mode, access to its operation from its front panel controls or from a guest-mode
remote can be limited, depending upon the settings of the Institutional TV features. For examples, the unit’s front panel
controls can be “locked-out” (rendered inoperable), only certain channels can be selected, and/or the volume can be lim-
ited to a given range.
Consumer Mode: When in the Consumer mode, the unit operates as a standard TV, bypassing the Institutional
Television feature set, thus allowing normal initial power ON, channel selection, and volume control (as well as a vari-
ety of selectable Menu features). When the TV is in Consumer mode, Philips RC-5 system 0 (guest-mode) remotes, such
as the RC2524BK and the RL9820BK (optional accessories) can access the Consumer-mode Main Menu, and configure
the television to the full extent offered in this mode. Guest-mode 21-button remotes such as the RC2524BK use the Menu
button to access the Consumer menu. Guest-mode 20-button remotes such as the RL9820BK, which do not have a Menu
button, use the Sleep button to access the Consumer menu. Simultaneously pressing the front panel’s Volume - and
Volume + buttons also invokes the Consumer menu.
Identifying the Operational Mode: To identify the television’s operational mode, a system 7 (commercial setup mode)
master setup remote (RG4172BK, optional accessory) must be used. With the RG4172BK in setup mode (press TV
SETUP on the RG4172BK), press Recall. The following information will appear on-screen:
STATUS ITEM
STATUS DATA
MEANING
SYSTEM STATUS (LO1ITV-US4PV)
n/a
Information title
MODE
COMMERCIAL / CONSUMER
CHANNEL, INPUT (CHANNEL, INPUT)
OFF / ON
Operational mode
CHANNEL
DCM
Currently-tuned channel
Data communications module offline /
online
CODES
211 222 001 035
TUNED / NOT TUNED
0031h
Internal data for factory / service use.
Signal present / absent
SIGNAL
OP HRS
Number of cumulative hours unit has
been operated (hexadecimal)
ERRORS
0 0 0 0 0
3.3
Internal data for factory / service use.
Television software version.
VERSION
Changing Operational Modes: To change the television’s mode between Consumer and Commercial modes, a system
7 (commercial setup mode) master setup remote must be used. With the RG4172BK in setup mode (press TV SETUP on
the RG4172BK), enter the following keystroke sequence: 0 2 4 9 9 5 Menu. Only the RG4172BK, when it is in setup
mode can change the television’s mode between Consumer and Commercial, and provide complete access to the televi-
sion’s Institutional Features. The RG4172BK can be set to operate in either its master setup remote mode, or in guest-
mode. The RG4172BK’s guest mode facilitates testing the desired Institutional / Commercial configuration.
3
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
SETTING THE INSTITUTIONAL TV OPERATIONAL MODE
To change the operational mode of the Philips Institutional TV, use the RG4172BK in setup mode (press TV SETUP on
the RG4172BK), and enter the following keystroke sequence: 0 2 4 9 9 5 Menu. Select the desired mode from the
Operational Mode menu. IMPORTANT NOTE: IF YOU CHANGE THE OPERATIONAL MODE TO CONSUMER MODE,
YOU MUST POWER THE TELEVISION OFF AND BACK ON TO COMPLETE THE MODE CHANGE.
NOTE: ONCE THE TELEVISION IS IN CONSUMER MODE, DO NOT USE THE SETUP REMOTE TO ACTIVATE COMMER-
CIAL FEATURES. OTHERWISE, THE COMMERCIAL FEATURES WILL AFFECT CONSUMER OPERATION. IT WILL THEN
BE NECESSARY TO PLACE THE TELEVISION BACK INTO COMMERCIAL MODE, THEN INTO CONSUMER MODE, AND
THEN POWERED OFF AGAIN TO PROPERLY PLACE THE TELEVISION BACK INTO CONSUMER MODE.
OPERATIONAL MODE
CURRENT MODE
COMMERCIAL / CONSUMER
PRESS 1
CONSUMER MODE:
COMMERCIAL MODE:
PRESS 2
EXIT WITHOUT CHANGING MODES:
PRESS 0
PHILIPS INSTITUTIONAL TV REMOTE CONTROLS
Remote controls (optional accessories) used with Philips Institutional televisions.
RC2524BK
RL9820B
RG4172BK
RC2573*
Guest Remote
Guest Remote
Setup Remote
Future version of mas-
ter setup remote. Fully
functionally equivalent
to RG4172BK. Put
switch in SETUP posi-
tion to place remote in
setup mode. *Exact
model number subject
to change.
29-button guest remote 20-button guest remote.
with menu button, addi-
tional features (VCR con-
trol, etc.)
Master setup remote.
Required to change
operational modes and
access Institutional fea-
tures. Press TV SETUP
to place remote in
SETUP mode.
4
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
ITV MENU ITEMS & AVAILABILITY IN CONSUMER & COMMERCIAL MODES (MODELS PRF227S, PLW225S)
The following table summarizes the Commercial and Consumer menu items available on your Philips Institutional tele-
vision. The functions of these menu items will be discussed in greater detail later in this booklet. Menu items denoted
with a “>” invoke sub-menus, which will also be discussed later in this booklet. The column labeled CONSUMER indi-
cates the Main Menu items that are available when the television is in Consumer mode, and Menu or Sleep is pressed on
a guest-mode remote (or RG4172BK master setup remote in guest mode). The column labeled COMMERCIAL indicates
the Setup Menu items available with the RG4172BK master setup remote whenever the setup remote is in setup mode.
MENU ITEM
MENU TITLE
SETTINGS / OPTIONS
SETUP MENU / MAIN MENU
COMMERCIAL
CONSUMER
SETUP MENU
MAIN MENU
LANGUAGE
CHANNEL INSTALL
CABLE TUNING
BRIGHTNESS
COLOR
ENGLISH/ESPANOL/FRANÇAIS
>
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
ON/OFF
----|---- 0 - 63
----|---- 0 - 63
CONTRAST
SHARPNESS
TINT
----|---- 0 - 63
----|---- 0 - 63
----|---- -31 - +31
ON/OFF
NOISE REDUCTION
SOUND MODE
SAP
MONO / STEREO
OFF / NO SAP / ON
FIXED / VARIABLE
----|---- 0
AUDIO OUT
BALANCE
TREBLE
----|---- -31 - +31
----|---- -31 - +31
ON / OFF
BASS
INCRED STEREO
AVL
ON / OFF
VOLUME BAR
MIN VOLUME *
MAX VOLUME *
SWITCH ON VOLUME *
ON / OFF
----|---- 0 - 63
----|---- 0 - 63
----|---- 0 - 63 / STANDARD
SWITCH ON CHANNEL * Ch. 1-125 / FRONT / AUX / S-VIDEO / CVI / STANDARD
POWER ON *
STANDARD / FORCED
CHANNEL DISPLAY *
KEYBOARD LOCK *
ESP *
NUMBER/LABEL/ALL/NONE
ON/OFF
1-99/OFF
AUDIO/VIDEO MUTE
EXT AUD / VID OUT
WELCOME MESSAGE *
CHANNEL GUIDE *
REMINDER
OFF / BLACK / BLUE
x
x
ON / OFF
>
POWER ON/OFF/ON
ON / OFF
x
x
3 DIGIT ENTRY *
A/CH A/V SWITCH *
CC
ON / OFF
ON / OFF
OFF/CC-1/CC-2/CC ON MUTE
SAVE CC *
ON / OFF
V-CHIP MENU ITEM *
SAVE V-CHIP *
V-CHIP SETUP
SLEEPTIMER
ON / OFF
ON / OFF
>
x
x
OFF/15/30/45/60/90/120/180/240
SECURITY *
STANDARD/HIGH
>
EXIT
x
* COMMERCIAL FEATURE
5
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
ITV Menu Items & Availability In Commercial Mode (Features Menu) (models PRF227S, PLW225S)
The following menu is available on your Philips Institutional television when it is in Commercial mode. The Features
Menu items are limited to the following when pressing Menu or Sleep on a guest-mode remote (or RG4172BK master
setup remote in guest mode), or when pressing the front panel keyboard’s VOLUME + and VOLUME - simultaneously
(provided the television’s front panel keyboard has not been locked out, see KEYBOARD LOCK).
FEATURES MENU
CC
OFF/CC-1/CC-2/CC ON MUTE
SLEEPTIMER
OFF/15/30/45/60/90/120/180/240
V-CHIP SETUP (see V-CHIP MENU ITEM)
EXIT
>
>
Notes:
ꢀ Regardless of whether the television is in Consumer or Commercial mode, if you press Menu on an RG4172BK
master setup remote when the setup remote is in setup mode, the television’s SETUP MENU described earlier will
appear.
ꢀ
Certain features that are unique to commercial setup, such as POWER ON FORCED and KEYBOARD LOCK will
remain in effect immediately after the television is placed in Consumer mode IF THE TELEVISION IS NOT FIRST POW-
ERED OFF. Such features are denoted with a “*” in the menu item summary and descriptions.
ꢀThe limited Features Menu appears when the television is in Commercial mode and a guest remote (or setup remote
in guest mode) Menu or Sleep button is pressed, or when the television’s front panel keyboard VOLUME - and VOL-
UME + are pressed simultaneously (provided the television’s front panel keyboard is not locked out, see KEYBOARD
LOCK).
Front Panel Controls*
Refer also to the sections in this documentation regarding the use of the front panel controls, specifically front keyboard
lock-out*.
PRF227S: The PRF227S front panel is limited to power on/off.
PLW225S: The PLW225S front panel consists of power on/off, volume, and channel controls. Channel - and Channel +
normally change the television’s channel or input to any of the channels or inputs currently in the Channel Ring (see
Channel Ring). Volume + and Volume - normally control the television’s audio volume. However, simultaneously press-
ing Volume + and Volume - invokes a menu. This will be either the Features Menu (see Features Menu, if the television
is in Commercial Mode, or the Main Menu, if the television is in Consumer Mode. Once either menu is active, Channel
+ and Channel - navigate vertically to select a menu item, and Volume + and Volume - change the currently-selected menu
item.
* NOTE: FRONT PANEL CONTROLS ARE INOPERATIVE IF THE FRONT KEYBOARD HAS BEEN LOCKED OUT. SEE FRONT
KEYBOARD LOCKOUT.
6
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
HOW TO USE THE ON-SCREEN MENU
This section explains the Philips Institutional Television’s menu items. As described previously, the availabili-
ty of each item depends upon the television’s current operational mode (Consumer or Commercial) and the
type of remote control command (guest or setup) issued.
LANGUAGE
SETUP ꢁ
CONSUMER ꢁ
FEATURES MENU ꢂ
An on-screen LANGUAGE option is available. You may set the TV's onscreen menu to appear in either English, French,
or Spanish text. With the Main Menu onscreen press the Menu button repeatedly, or use the Cursor (s) Up and Down (t)
buttons, to select LANGUAGE with the TV’s highlight control bar. Press the Cursor Right (+>) or Left (<- ) button on
the remote to select English, French (FRANCAIS), or Spanish (ESPANOL). Text in the onscreen Menu will appear in the
selected language. Remember, the Language control only makes the TV's onscreen Menu items appear in French or
Spanish text. It does not change the language of other onscreen text features, such as Closed Captioning.
CHANNEL INSTALL
SETUP ꢁ
CONSUMER ꢁ
FEATURES MENU ꢂ
When highlighted, use Channel Up/Down, or enter the desired channel number using the Number buttons you wish to
edit. The following control items, contained within the Channel Installation menu, will affect the chosen channel.
CHANNEL INSTALLATION
CHANNEL
FRONT / AUX / SVIDEO / CVI / 1 - 125
CHANNEL RING
INPUT
SAVED / DELETED
(ANTENNA) / FRONT / AUX / SVIDEO / CVI
LABEL
(--------)
VIDEO BLANK
AUDIO BLANK
AUTO PROGRAM
EXIT
OFF / ON
OFF / ON
>
>
CHANNEL RING - When highlighted, press the Cursor Right (+>) or Left (<- ) buttons on the remote to choose SAVED
(or DELETED). When SAVED is selected, the channel will remain or be added to the TV’s program memory. When
DELETED is selected, the channel will be dropped from the TV’s program memory and will not appear when the TV
channels are scanned (using the Channel +,- buttons).
INPUT - When highlighted, press the Cursor Right (+>) or Left (<- ) buttons on the remote to select ANTENNA,
FRONT, AUX, S-VIDEO, or CVI input signal options. The Input control directs the TV to select the specific indicated
input whenever this channel is tuned.
LABEL - When highlighted, press the Cursor Right (+>) button on the remote to select the first character space area.
Then press the Cursor Up and Down buttons to scroll through the list of available letter characters/numbers/& symbols
provided for your labeling use. Press the Cursor Right (+>) button to highlight the next character space and continue to
repeat the process until the complete label or channel title has been entered. The Channel Label will appear in the corner
of the TV screen beside the selected channel number.
VIDEO BLANK - When highlighted, press the Cursor Right (+>) or Left (<- ) buttons to turn the VIDEO BLANK con-
trol ON (or OFF). When ON, no video will be shown when this specific channel is tuned. When OFF, normal viewing of
video for this specific channel will take place.
AUDIO BLANK - When highlighted, press the Cursor Right (+>) or Left (<- ) buttons to turn the AUDIO BLANK con-
trol ON (or OFF). When ON, no sound will be heard through the TV speakers when the channel is tuned. When OFF,
normal sound playback will be heard for the selected channel.
CHANNEL - When highlighted, use Channel Up/Down, or enter the desired channel number using the Number buttons
you wish to edit. The following control items, contained within the Channel Installation menu, will effect the chosen
channel.
AUTO PROGRAM - When highlighted, press the Cursor Right (+>) or Left (<- ) buttons to begin an automatic chan-
nel search for all available received signal programs. Any channels found will be SAVED in the TV’s program memory.
7
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
HOW TO USE THE ON-SCREEN MENU (CONTINUED)
CABLE TUNING (OFF / ON)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
Your Philips television can be configured to operate in either Cable TV or broadcast / off-air tuning modes. In other
words, the TV must be configured depending upon whether a Cable TV signal or a normal antenna signal is applied to
its 75-ohm ANT/CABLE plug.
With the Menu onscreen, press the Menu button repeatedly , or use the Cursor Up and Down buttons, to select CABLE
TUNING with the TV's highlight control bar. Press the Cursor Right or Left button on the remote to select:
ON if you DO have Cable TV connected to the TV. Channels 1-125 may then be selected. Or, select OFF if you have an
Antenna connected to the TV, and then only channels 2-69 may be selected. Press STATUS/EXIT to remove the on-
screen menu.
BRIGHTNESS, COLOR, CONTRAST, SHARPNESS, TINT
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
Use the cursor-up and cursor-down buttons to select the picture parameter you wish to adjust. Use cursor left (<-) and
cursor right (+>) to adjust the picture parameter.
NOISE REDUCTION (ON/OFF)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
This feature reduces video noise in the displayed picture. Effectively reduces noise while having maximum peaking in
the bright parts of the picture. Differs from reducing Sharpness (see Sharpness) in that noise is reduced, but picture
detail is preserved.
SOUND MODE (MONO / STEREO)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
Use cursor left (<-) and cursor right (+>) to select monaural or stereo audio mode.
SAP (OFF / NO SAP / ON)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
Second Audio Program (SAP) is part of the stereo broadcast system. Sent as an additional audio channel SAP can be
heard apart from the current TV program sound. TV stations are free to use SAP for any number of purposes, but may
be used for foreign language translations of TV shows (or for weather and news bulletins). If a SAP signal is not pres-
ent with a selected program the SAP option cannot be selected
AUDIO OUT (FIXED / VARIABLE)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
When the FIXED audio out option is selected, the left and right audio outputs are fixed at a nominal 0.5vrms signal
level, and are unaffected by the television’s volume control setting. When the VARIABLE audio out option is selected,
the left and right audio outputs are controlled by the television’s volume control setting, and variable between 0.2vrms
and 2vrms nominal signal levels.
BALANCE / TREBLE / BASS (-----||||| nn)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
Use the cursor-up and cursor-down buttons to select the audio parameter you wish to adjust. Use cursor left (<-) and
cursor right (+>) to adjust the audio parameter.
INCREDIBLE STEREO (ON / OFF)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
Processes the left and right audio channels to achieve a perceived increase in channel separation and spatial effect. Use
cursor left (<-) and cursor right (+>) to turn this feature on and off.
AVL (ON / OFF)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
Automatic volume leveling restricts the volume variation of audio signals to a relatively small range by boosting low-
level signals and reducing louder signals, thus maintaining a consistent volume level. Use cursor left (<-) and cursor
right (+>) to turn this feature on and off.
8
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
NOTES
9
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
HOW TO USE THE ON-SCREEN MENU (CONTINUED)
MIN VOLUME / MAX VOLUME* (VOL |||||---- nn)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. Limits the range throughout which the television’s
volume can be adjusted by a guest mode remote control, or by the television’s front panel keyboard (provided the front
panel keyboard has not been locked out, see KEYBOARD LOCK).
VOLUME BAR (ON / OFF)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
The Volume Bar feature, when set to ON, causes a volume change verification (VOL ||||||---- nn, where nn equals some
numeric value between 0 - 63) to appear on-screen whenever the volume is adjusted
SWITCH ON VOLUME* (||||||---- 0 - 63 / STANDARD)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. This feature determines the television’s volume when-
ever it is first turned on. A value (0 - 63) can be specified, or default to the television’s volume when last turned off
(STANDARD).
POWER ON* (STANDARD / FORCED)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. POWER ON FORCED means that the television will
automatically power-up whenever it is supplied with mains power. When POWER ON is set to FORCED, the television
will remain powered on long as mains power is applied, and cannot be turned off by a guest-mode remote, or by the
front panel keyboard (even if it is not locked out). POWER ON STANDARD means that the television will not auto-
matically power-on when mains power is applied.
CHANNEL DISPLAY* (NUMBER / LABEL / ALL / NONE) SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. CHANNEL DISPLAY determines the channel infor-
mation (NUMBER and / or LABEL), if any, that is displayed briefly whenever the channel is changed. Also see LABEL
in CHANNEL INSTALLATION. Also see REMINDER.
KEYBOARD LOCK* (ON / OFF)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. When KEYBOARD LOCK is OFF, the television’s
front panel keyboard will be accessible, but only to the extent depending upon the MIN VOLUME, MAX VOLUME,
POWER ON, and CHANNEL INSTALLATION. KEYBOARD LOCK, when ON, completely disables the television’s
front panel keyboard (Power, Volume -, Volume +, Channel -, Channel +).
ESP* (OFF / 1 - 99)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. ESP (Energy Savings Programmability), if not OFF,
determines the number of hours (1 - 99) the television will remain powered on after the most recent front panel keyboard
or remote control command. NOTE: If POWER ON (see POWER ON STANDARD / FORCED) is set to FORCED,
ESP has no effect.
AUDIO / VIDEO MUTE (OFF / BLACK / BLUE)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
AUDIO / VIDEO MUTE, also known as “A/V muting” eliminates annoying “static” and “snow” when no tuner or exter-
nal signal is present. When set to BLACK or BLUE, sets the screen set to a solid black or blue display, respectively, and
forces audio to be muted, when no valid tuner / video signal is present at the selected source.
EXTERNAL AUD/VID OUT (OFF / ON)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
To enable the Monitor Out jacks on the rear jack panel, set EXTERNAL AUD/VID to ON. When the Monitor Out jacks
are enabled, they provide the currently-selected source (tuner or video) signals, UNLESS CVI (COMPONENT VIDEO INPUT)
VIDEO IS SELECTED. IF CVI is the selected input, no video signal will be present at the Monitor Out video jack.
When EXTERNAL AUD/VID is set to OFF, no signals will be present at the Monitor Out jacks.
* COMMERCIAL FEATURE
10
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
HOW TO USE THE ON-SCREEN MENU (CONTINUED)
WELCOME MESSAGE* (>)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. The Welcome Message feature makes it possible for
an on-screen message to appear whenever the television is first turned on. The message will remain until any front-panel
keyboard command or remote control command is received. The Welcome Message sub-menu is shown below.
WELCOME MESSAGE
MESSAGE
LINE 1
LINE 2
CLEAR
OFF / ON
(20 characters)
(20 characters)
>
>
EXIT
Use cursor-up and cursor-down to select the Welcome Message sub-menu item. While Line 1 or Line 2 of the Welcome
Message message is highlighted, use cursor-left and cursor-right to enter message-edit mode and position the cursor with-
in the line of the message content. Use cursor-up and cursor-down to change the character at the current position. Press
RECALL on the Setup Remote to exit the editing mode and resume Welcome Message sub-menu item selection.
ꢀ
NOTE: WELCOME MESSAGE, when ON, overrides CHANNEL GUIDE at power-on, if the latter has been
enabled.
CHANNEL GUIDE* (OFF / ON / POWER ON)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. CHANNEL GUIDE provides an on-screen list of all
channels / inputs currently saved in the channel ring (see CHANNEL INSTALL) and their corresponding labels (see
CHANNEL INSTALL), for any channels / inputs for which labels have been assigned. When CHANNEL GUIDE is ON,
the channel guide appears when a remote control CH GDE command is received. When CHANNEL GUIDE is set to
POWER ON, the channel guide appears when the television is first powered on, as well as when a remote control CH
GDE command is received. When CHANNEL GUIDE is OFF, the channel guide never appears.
REMINDER* (OFF / ON)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢂ
The REMINDER feature, when ON, causes the television to constantly display the currently-tuned channel / input and/or
its label (if one has been assigned, see CHANNEL INSTALLATION) in the upper-left-hand corner of the screen. When
REMINDER is OFF, the channel number / label will only appear briefly immediately after channel / input is selected.
NOTE: The REMINDER feature is available in the television’s commercial-mode TV SETUP and CONSUMER menus.
3-DIGIT ENTRY* (OFF / ON)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. Determines whether two or three remote-control digit
commands initiate a channel-tune command. When OFF, tuning will occur upon the reception of two remote-control digit
commands. When ON, tuning will occur upon the reception of three remote-control digit commands.
* COMMERCIAL FEATURE
11
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
A/CH A/V SWITCH* (OFF / ON)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Available in / applicable to Commercial Setup Menu / Commercial Mode. Alternate channel Audio / Video switching.
When A/CH A/V SWITCH is OFF, the remote-control A / CH (alternate channel) command causes the television to select
the channel / input that was selected just prior to the currently-selected one. When A/CH A/V SWITCH is ON, the
remote-control A / CH (alternate channel) command causes the television to successively switch between all A/V inputs
currently saved in the Channel Ring and the television’s most-recently-tuned RF channel.
CC (OFF / CC-1 / CC-2 / CC ON MUTE)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢁ
This feature activates closed-captioning mode 1 or mode 2 when CC-1 or CC-2, respectively, is selected. When CC ON
MUTE is selected, CC-1 is activated when the television receives a remote-control MUTE command.
SAVE CC* (OFF / ON)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Applicable / available only to the Commercial Mode / setup menu. When SAVE CC is OFF, the television will always
power-up with closed-captioning turned off. When SAVE CC is ON, the television “remembers” the most recently-
selected closed-captioning mode. In other words, the television will always power-up with closed-captioning set to the
mode to which it was last set.
V-CHIP MENU ITEM * (OFF / ON)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Available in / applicable to Commercial Setup Menu / Commercial Mode. Determines whether the V-CHIP SETUP menu
item appears when the television is in COMMERCIAL MODE and is displaying the FEATURES MENU (see COM-
MERCIAL MODE / FEATURES MENU).
SAVE V-CHIP (OFF / ON)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Available in / applicable to Commercial Setup Menu / Commercial Mode. When SAVE V-CHIP is ON, the television
“remembers” the most recently-selected V-CHIP configuration. In other words, the television will power-up with V-
CHIP in the state in which it was last configured.
V-CHIP SETUP (>)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢁ
V-Chip setup menu.
SLEEPTIMER (OFF / 15 / 30 / 45 / 60 / 90 / 120 / 180 / 240)
SETUP ꢁ CONSUMER ꢁ FEATURES MENU ꢁ
Determines the amount of time, in minutes, subsequent to the selection of the specified interval, that the television will
remain powered-on before automatically powering off.
SECURITY * (STANDARD / HIGH)
SETUP ꢁ CONSUMER ꢂ FEATURES MENU ꢂ
Available in / applicable to Commercial Setup Menu / Commercial Mode. When SECURITY is set to STANDARD,
access to the television’s Commercial Setup Menu is possible with a guest-mode remote control, by means of the follow-
ing remote-control keystrokes: 3 1 9 7 5 3 MUTE.
!NOTE: The SECURITY item itself does not appear when the Commercial Setup Menu is invoked in this manner. This
feature, as with all Commercial Setup features, can only be changed with a Master Setup Remote.
* COMMERCIAL FEATURE
12
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
Side Jack Panel
JACK PANELS
Rear Jack Panel
Jack Panel Information
- The setting of the Commercial menu item EXT AUD/VID OUT determines whether or not signals will be pres-
ent at the rear jack panel’s Monitor Out jacks. If EXT AUD/VID OUT is set to OFF, no signals will be present
at these jacks.
- When using CVI (component video input), no video signal will be present at the video monitor output jack,
even if EXT AUD/VID OUT is set to ON.
- The rear jack panel's left and right audio inputs are shared among all rear jack-panel external video inputs. Thus,
regardless of which rear jack-panel video input is selected (Video, S-Video, CVI), the audio signals present at
the audio inputs will be heard.
13
RENEWED
90 DAY
LIMITED WARRANTY
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
FACTORY DEFAULT SETTINGS
INITIAL VOLUME SETTING (0 - 63)
15
AUX / S-VIDEO AVAILABLE
COMMERCIAL / CONSUMER
OFF
COMMERCIAL
YES
MONITOR-OUT JACKS
COMPONENT VIDEO IN
YES
LANGUAGE (ENGLISH / FRANCAIS / ESPANOL)
CHANNEL INSTALL (> ANY RINGS & ADD/DELETE)
PROPLUS SETUP (> EVENTS 1-7 ENABLED/DISABLED)
CABLE TUNING (ON / OFF)
BRIGHTNESS (0 - 63)
ENGLISH
2-13
n/a
ON
28
COLOR (0 - 63)
22
CONTRAST (0 - 63)
57
SHARPNESS (0 - 63)
25
TINT (-31 - +31)
0
NOISE REDUCTION (ON / OFF)
SOUND MODE (MONO / STEREO)
SAP
OFF
STEREO
X
AUDIO OUT (FIXED/VARIABLE)
BALANCE (-31 - +31)
VARIABLE
0
TREBLE (0 - 63)
31
BASS (0 - 63)
31
INCREDIBLE STEREO (ON / OFF)
AVL (OFF / ON)
OFF
OFF
VOLUME BAR (OFF / ON)
OFF
MIN VOLUME (0 - 63)
0
MAX VOLUME (0 - 63)
63
SWITCH ON VOLUME (STANDARD / 0 - 63)
SWITCH ON CHANNEL (STD/FRONT/AUX/TV1-TV125)
POWER ON (STANDARD / FORCED)
CHANNEL DISPLAY (NONE / NUMBER / LABEL / ALL)
KEYBOARD LOCK (ON / OFF)
ESP (OFF / 1 - 99)
STANDARD
STANDARD
STANDARD
ALL
OFF
OFF
A/V MUTE (OFF / BLACK / BLUE)
EXT AUD / VID OUT
OFF
ON
WELCOME MESSAGE (> MESSAGE ON/OFF)
CHANNEL GUIDE (OFF / ON / POWER ON)
REMINDER (OFF / ON)
OFF
OFF
OFF
THREE DIGIT ENTRY (OFF/ON)
A/CH A/V SWITCH (ON / OFF)
CC (OFF / CC-1 / CC-2 / CC ON MUTE / OFF)
SAVE CC (OFF / ON)
OFF
ALT/CH
OFF
OFF
V-CHIP MENU ITEM (OFF / ON)
SAVE V-CHIP (OFF / ON)
OFF
OFF
V-CHIP SETUP (>MASTER DISABLE OFF/ON)
SLEEPTIMER (OFF/15-240)
SECURITY (STANDARD / HIGH)
OFF
OFF
STANDARD
15
PLW225S & PRF227S DFU
# 3135-125-20871
PRELIMINARY 04/15/02
DIMENSION DRAWINGS
PLW225S
PRF227S
16
PRELIMINARY 04/15/02
INDEX
3-DIGIT ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OPERATIONAL MODE, IDENTIFYING . . . . . . . . . . . . 3
PHILIPS INSTITUTIONAL TVSOFTWARE . . . . . . . . . 3
POWER ON* (STANDARD / FORCED). . . . . . . . . . 10
RC2524BK GUEST REMOTE . . . . . . . . . . . . . . . . . . . 4
RC2573 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
REMINDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 5, 10-11
RG4172BK SETUP REMOTE . . . . . . . . . . . . . . . . . . . 3-6
RL9820B GUEST REMOTE. . . . . . . . . . . . . . . . . . . . . 4
SAFETY / PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . 2
SAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SAVE CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SAVE V-CHIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SECURITY (STANDARD / HIGH) . . . . . . . . . . . . . . . . 5, 12, 15
SETTINGS, FACTORY DEFAULT . . . . . . . . . . . . . . . 15
SETUP, ACCESS TO WITHOUT SETUP REMOTE . 12
SLEEPTIMER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SOUND MODE (MONO / STEREO). . . . . . . . . . . . . . 8
STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SWITCH ON VOLUME. . . . . . . . . . . . . . . . . . . . . . . . 10
V-CHIP MENU ITEM . . . . . . . . . . . . . . . . . . . . . . . . . 12
V-CHIP SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VIDEO BLANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
VOLUME BAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
WELCOME MESSAGE . . . . . . . . . . . . . . . . . . . . . . . 11
A/CH A/V SWITCH. . . . . . . . . . . . . . . . . . . . . . . . . . . 12-PB 12
AUDIO BLANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AUDIO OUT (FIXED / VARIABLE). . . . . . . . . . . . . . . . 8
AUDIO/ VIDEO MUTE . . . . . . . . . . . . . . . . . . . . . . . . 10
AUTO PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AVL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
BALANCE / TREBLE /BASS . . . . . . . . . . . . . . . . . . . . 8
BRIGHTNESS, COLOR, ETC.. . . . . . . . . . . . . . . . . . . 8
CABLE TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CHANGING OPERATIONAL MODES . . . . . . . . . . . . . 3
CHANNEL DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . 10
CHANNEL GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CHANNEL INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CHANNEL RING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
COMMERCIAL MODE . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONSUMER & COMMERCIAL MODES . . . . . . . . . . . 5
CONSUMER MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DIMENSION DRAWINGS. . . . . . . . . . . . . . . . . . . . . . 16
ESP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EXTERNAL AUD / VID OUT . . . . . . . . . . . . . . . . . . . 10
FACTORY DEFAULT SETTINGS. . . . . . . . . . . . . . . . 15
FRONT PANEL CONTROLS. . . . . . . . . . . . . . . . . . . . 3, 6
GUEST MODE REMOTE. . . . . . . . . . . . . . . . . . . . . . . 3
IDENTIFYING THE OPERATIONAL MODE . . . . . . . . 3
INCREDIBLE STEREO . . . . . . . . . . . . . . . . . . . . . . . . 8
INPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ITV MENU ITEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
JACK PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
KEYBOARD LOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LABEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . 14
LOCK-OUT, KEYBOARD . . . . . . . . . . . . . . . . . . . . . . 10
MENU ITEMS, COMMERCIAL & CONSUMER. . . . . . 5
MIN VOLUME/ MAX VOLUME. . . . . . . . . . . . . . . . . . 10
NOISE REDUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATIONAL MODE, CHANGING. . . . . . . . . . . . . . 3-4
17
|