30” WIDE LCD Color TV/MONITOR
Owner’s Manual
Model:LT-30FMP
Warnings
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN.
WARNING :
To reduce the risk of electric shock do not remove cover (or back).
No user serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons..
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THE SET TO RAIN OR
MOISTURE.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to
Article 820-40 of the National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close to the point
of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B
DIGITAL device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a residential Installation. This equipment generates, uses and can
radiate radio frequency energy and, if Not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization.
Unauthorized modification could void the user’s authority to operate this product.
3
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use
can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have
been built into your new product, please read and observe the following safety points when
installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this operating guide can help you get many years
of enjoyment and safe operation that are built into your new product.
This product complies with all applicable U.S. Federal regulations and voluntary safety standards.
1. Read Instructions
9. Attachments
All the safety and operating instructions
Do not use attachments not recommended by the
product manufacturer as they may cause
hazards.
should be read before the product is
operated.
2. Follow Instructions
10. Ventilation
All operating and use instructions should e
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be locked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer ’s instructions have been adhered
to.
followed.
3. Retain Instructions
The safety and operating instructions should
be retained for future reference.
4. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water for
example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or
near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or
tilted surface, or on an unstable cart, stand,
tripod, bracket, or table. The product may
slide or fall, causing serious injury to a child or
adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or
sold with the product. Any mounting of the
product should follow the manufacturer’s
instructions, and should use a mounting
11. Power Sources
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your product dealer
or local power company. For products intended
to operate from battery power, or other sources,
refer to the operating instructions.
12. Power Cord Polarization
This product is equipped with a three-wire
grounding-type plug, a plug having a third
(grounding) pin This plug will only fit into a
grounding-type power outlet. . This is a safety
feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
accessory
manufacturer.
8. Transporting Product
A product and cart combination should be
recommended
by
the
13. Power Cord Protection
Power-supply cords should be routed so that
they are not likely to be walked on or pinched by
items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
moved with care. Quick stops, excessive
force, and
may cause
cart
uneven surfaces
the product and
combination to
overturn.
4
PORTABLE CART WARNING
IMPORTANT SAFETY INSTRUCTIONS
14. Outdoor Antenna Grounding
19. Servicing
If an outside antenna or cable system is
connected to the product, be sure the antenna or
cable system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Article 810 of the National
Electrical Code (U.S.A.), ANSI/NFPA 70 provides
information with regard to proper grounding of
the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna-
discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode.
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by f
ollowing the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or the cabinet
has been damaged.
Example of Grounding According to National
Electrical Code Instructions
f. If the product exhibits a distinct change in
performance.
21. Replacement Parts
15. Lightning
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
For added protection for this product (receiver)
during a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
22. Safety Check
16. Power Lines
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
An outside antenna system should not e
located in the vicinity of overhead power lines
or other electric light or power circuits, or where
it can fall into such power lines or circuits.
When installing an outside antenna system,
extreme care should be taken to keep from
touching such power lines or circuits, as
contact with them might be fatal.
23. Wall Mounting
The product should be mounted to a wall only as
recommended by the manufacturer. The product
may slide or fall, causing serious injury to a child or
adult, and serious damage to the product.
24. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
17. Overloading
Do not overload wall outlets and extension
cords as this can result in a risk of fire or
electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
5
Contents
Before operating the set, please read this manual carefully.
3
4~5
7
Warnings
Important Safety Instructions
Contents
Supplied Accessories
Controls
Channel of panel
Remote controller
Basic Operation
On and off
8
9~11
9
10~11
12
12
Channel selection
Volume adjustment
Q.View
12
12
12
Mute Function
12
On screen Language selection
On Screen Menus and Displays
Setting up TV Channel
Auto Program
12
13
14~16
14
Manual Program
Program Iist
15
16
Picture Control
Manual picture control
Auto picture control
Sound Control
17
17
17
18
Captions
19
Parental Control
Other functions
TV, VIDEO, COMPONENT and S-VIDEO mode
Auto sleep
20~22
23~24
23
23
Blue Back
23
Auto Wide
23
Sleep timer
24
SAP
24
PIP function
24
External Equipment Connection
Antenna Connection
COMPONENT INPUT
A/V INPUT
25~26
25
25
25
S-VIDEO INPUT
DTV INPUT
26
26
Headphone OUT
Sub Woofer OUT
Connecting PC as monitor
Product specifications
Troubleshooting
Limited Warranty
26
26
27~28
29
30
31
7
Supplied Accessories
L Make sure the following accessories are provided with Product.
1. AC/DC adaptor
2. AC cord
4. Batteries (2EA)
3. Remote controller
6. PC ANALOG IN cable
PSM
TV/AV
CH
CH
VOL
VOL
5. Owner’s manual
7. PC DIGITAL IN cable
30" Wide LCD Color TV/Monitor
Owner's Manual
Model: LT-30FMP
8. PC Audio IN cable
본
제품은 국내에서만 사용할
수
있습니다.
사용설명서를 읽고 난 뒤에는 제품을 사용하는 사람이
볼
수
있는 곳에 보관해 주십시오.
Battery installation
uInserting batteries
1. Remove the battery cover by pulling it upward in the direction shown by the arrow.
2. Insert the batteries with correct polarity ( "+" to "+", and "-" to "-" ).
3. Replace the battery compartment cover.
→
→
*Install two high-quality 1.5V "AAA" alkaline batteries. Don't mix old batteries with
new batteries.
*Remove batteries when you won't use the remote controller for long time. Liquid
leakage from old batteries may cause operation failure.
uNotes for using remote controller
• Make sure there are no objects between the remote controller and its sensor.
• Don't place the remote control near a heater or in damp place. Strong impact to the
remote control may cause operation failure.
• Signal from the remote control may be disturbed by sun light or other bright light. In
this case, darken the room or move the TV.
8
Controls
1. ON/OFF Switches TV set on or off.
2. MENU
Displays a menu.
3. + CH - (Channel Up/Down)
Selects a Channel or a menu item.
4. + VOL - (Volume Up/Down)
Adjusts the volume./ Adjusts menu settings.
5. TV/AV Selects TV, VIDEO, COMPONENT, S-VIDEO, PC-ANALOG or PC-DIGITAL
or DTV(Option) mode./Clears the menu from the screen.
6. Power Indicator
Illuminates in red when the TV is in standby mode./ Illuminates in green when the TV
is switched on. Illuminates in blinked when the power save mode(only PC mode).
7. Remote control sensor
Accepts the IR signal of remote controller.
1
2
3
4
5
6
7
1. DC 24V adaptor input
2. PC ANALOG (D-SUB)
3. PC DIGITAL (DVI-I)
4. PC Audio IN
Connect the audio cable from the PC to the PC Audio IN of the set.
5. HEADPHONE out
Connect a headphone to this socket.
6. AUDIO IN[L(MONO)/R]
Connect the audio (L, R) output of S-VIDEO and COMPONENT.
7. S-VIDEO input
8. COMPONENT (DVD/DTV)
9. AV-IN
10. AV-OUT
11. Sub Woofer OUT
12. Ant. (Antenna input)
9
Controls
All the functions can be controlled with the remote controller. Some functions can
also be adjusted with the buttons on the front panel of the set.
Remote controller
Before you use the remote controller, please install
the batteries.
POWER
1
2
1
4
7
2
5
3
6
9
1. POWER
3
Turns the TV on from standby or off to standby mode.
8
0
2. MUTE
*
*
5
6
Turns the sound on and off.
PSM
SSM
SAP
4
7
MENU
TV/AV
CH
3. NUMBER buttons
8
Selects Channel numbers.
VOL
VOL
OK
TV/PC
SLEEP
4. PSM (Picture Status Memory)
10
CH
9
Recalls your preferred picture setting
CC
Q.VIEW
LIST
5. SSM (Sound Status Memory)
Recalls your preferred sound setting
PIP
ARC
INPUT
6. SAP
POSITION SWAP MODE
510-004B
CH
Adjusts the MTS-stereo, Mono, SAP
7. MENU
Displays a main menu.
8. TV/AV
Selects TV, VIDEO, COMPONENT, S-VIDEO, PC-
ANALOG, PC-DIGITAL or DTV mode.
Clears the menu from the screen.
9. SLEEP
Sets the sleep timer.
10. TV/PC
Selects TV , PC-ANALOG or PC-DIGITAL, DTV mode directly.
10
Controls
11. CHxy (Channel Up/Down)
Selects next Channel or a menu item.
POWER
12. VOLÏq (Volume Up/Down)
Adjusts the sound level.
Adjusts menu settings.
1
4
7
2
5
3
6
9
8
13. OK
0
*
*
Accepts your selection or displays the current mode.
PSM
SSM
SAP
MENU
TV/AV
14. CC
CH
13
12
Set the caption function.
11
VOL
VOL
OK
15. Q.VIEW
TV/PC
SLEEP
CH
Returns to the previously viewed Channel.
CC
Q.VIEW
LIST
16
15
14
16. LIST
Displays the program list menu.
18
17
PIP
ARC
INPUT
19
17. PIP
Displays a PIP(Picture In Picture) screen.
POSITION SWAP MODE
510-004B
CH
23
22
20
18. ARC
21
Selects a screen mode- 16:9, 14:9, ZOOM,1:1, 4:3.
19. INPUT
Selects the AV source of sub picture in PIP mode.
20. POSITION
Selects a position of PIP screen.
21. SWAP
Switches a main picture for sub picture in PIP mode.
22. MODE
Selects a PIP screen mode. – 16:1, 9:1, double window and scan mode.
It’s possible when a main mode is video mode.
23.xCHy
Selects a Channel when RF signal is displayed in PIP mode.
11
Basic Operation
Turning the TV On and Off
Standby Setup: The AC-DC converter and the AC power
cord must be set up and connected to have the TV in
standby mode ready to be turned on. Press the power
button on the front panel of the TV to go into standby
mode.
1. If the TV is in standby mode, press the Power
button on the remote controller or the TV itself to
turn the TV on.
2. Press the Power button again on the remote
controller or the TV itself to turn the TV off.
PSM
TV/AV
CH
CH
Note : If the TV is on and the power button is pressed to
turn the TV off, the TV goes into standby mode.
VOL
VOL
Channel selection
You can select a Channel number with the CHxy button
or NUMBER buttons.
Volume adjustment
Press the VOLÏq button to adjust the sound level.
Quick view
Press the Q.VIEW button to view the last channel you
were watching.
Sound mute function
Press the MUTE button. The sound is switched off and
the mute display
appears.
To cancel mute mode, press the MUTE button again,
VOLÏq, SSM button or SAP button.
On screen menu language selection
The menu can be displayed on the screen in desired
language.
Language
English
First select your language.
Français
1. Press the MENU button.
Español
2. Select the Setup menu.
3. Select the Language.
4. Press the CHxy button to select your desired
language.
▲▼
MENUꢀꢀTV/AV
5. Press the TV/AV button.
All the on screen menu will appear in the selected
language.
12
On Screen Menus and Display
1. Press the MENU button to display main menu.
Equalizer
Flat
2. Press the CHxy button to select menus-Picture,
Sound, Special, Setup.
Music
3. Adjust each menu with the VOLÏq button.
4. Press the MENU button to return to preceding menu.
5. Press the TV/AV button to finish adjusting menu.
Movie
Speech
User
0.1 0.5 1.5ꢀ 5.0ꢀꢀ10Khz
MENUꢀTV/AV
Picture
Contrast
Brightness
Color
Main menu
Picture
▲▼
90
75
75
50
0
q
q
q
q
Sound
Auto program
Tuner mode
Special
TV
Sharpness
Tint
Setup
Start
▲▼ ◀▶ MENUꢀꢀTV/AV
▲▼ ◀▶ MENUꢀTV/AV
▲▼ ◀▶ MENUꢀꢀTV/AV
Sound
Equalizer
Balance
AVL
Manual program
▶
Tuner mode
Channel
Fine
TV
0
7
Off
▶▶▶
▶▶▶
Surround
nVolume
MTS
Off
0
Search
Name
Mono
0
Sub woofer
Storage
On
▲▼ ◀▶ MENUꢀTV/AV
0-9 ▲▼ ◀▶ OKꢀMENUꢀTV/AV
Program Iist
PSM
TV/AV
Special
5
1
2
3
4
6
7
8
9
Input
TV
CH
CH
Auto Sleep
Blue back
Captions
Off
Off
Off
VOL
VOL
▲▼ ◀▶ OKꢀMENUꢀTV/AV
▲▼ ◀▶ MENUꢀꢀTV/AV
Language
English
Français
Setup
Español
Auto program
Manual program
Program Iist
▶
▶
▶
▶
▶
Language
▲▼
MENUꢀꢀTV/AV
Parental control
Parental control
Aux. Block Sources Unblocked
MPAA Unblocked
▲▼ ◀▶ MENUꢀTV/AV
Age Block
content Bik
Set Hours
▶
▶
* AV mode can select only Language and Parental
control in Setup menu.
◀▶ 00Hours
Set Passward ◀▶ ToꢀSet
LockꢀOn/OffꢀMustꢀSetꢀHours
13
Setting up TV Channel
Once you have preset the Channel, you will be able to use
the CHxy to scan the Channel you Programmed.
Channel can be tuned using Auto or Manual Program menu.
Auto program
Tuner mode
TV
Start
Auto Program
All Channel that can be received are stored by this
method. It is recommended that you use Auto Program
during installation of this set.
▲▼ ◀▶ MENUꢀꢀTV/AV
1. Press the MENU button.
2. Select the Setup menu.
3. Select the Auto program menu.
4. Press the CHxy button to select Tuner mode.
5. Select a Tuner mode with the VOLÏq button.
Ïq
TV
Cable
6. Select the Start with the CHxy button.
7. Press the VOLÏq button to start Auto program.
8. Press the MENU button to stop Auto Program.
9. Press the TV/AV button to return to normal TV
viewing.
PSM
TV/AV
CH
CH
VOL
VOL
14
Setting up TV Channel
Manual Program
Manual program
Tuner mode
Channel
Fine
TV
Manual Program lets you manually tune and arrange
the Channels in whatever order you desire. Also you can
assign a Channel name with 5 characters to each
Channel number.
7
▶▶▶
▶▶▶
Search
Name
1. Press the MENU button.
2. Select the Setup menu.
3. Select Manual program menu.
Storage
On
0-9 ▲▼ ◀▶ OKꢀMENUꢀTV/AV
4. Press the CHxy button to select Tuner mode.
5. Select a Tuner mode with the VOLÏq button.
Ïq
TV
Cable
6. Press the CHxy button to select Channel.
7. Select the Fine menu and adjust the received signal
with VOLÏq button.
8. Press the CHxy button to select Search. Press
the NUMBER buttons to commence searching.
9. Press the CHxy button to select Name.
Press the VOLÏq button. You can use a blank
+, -, the numeric 0 to 9, and the alphabet A to Z.
With the VOLÏq button, you can select in the
opposite direction.
PSM
TV/AV
CH
10. If this Channel is the one required, press the
CHxy button to select Storage. Press the VOLÏq
button twice to select On.
VOL
VOL
To select another channel,repeat steps 5 to 10.
CH
15
Setting up TV Channel
Program list
Program Iist
You can check the Programs stored in the memory by
displaying the Program list.
5
1
2
3
4
6
7
8
9
1. Press the MENU button.
2. Select the Setup menu.
3. Press the CHxy button select Program list.
▲▼ ◀▶ OKꢀMENUꢀTV/AV
Selecting a Channel in the Program list
Select a Channel with the CHxyor VOLÏq button.
The set switches to the chosen Channel number.
Paging through a Program list
When The set is TV mode, there are 7 program table
pages in which contain 69 programs and when the
set is cable mode, there are 13 program table pages
in which contain 125 programs.
Pressing the CHxy or VOLÏqbutton repeatedly
turns the pages.
The channel which is a signal is indicated with a white
color. The channel which is a no signal is indicated
with a blue color.
And the channel which searches a signal is indicated
with a yellow color.
PSM
TV/AV
CH
VOL
VOL
CH
16
Picture Control
You can adjust picture Contrast, Brightness, Color, Sharpness and Tint to the levels
you prefer.
Manual Picture Control
Picture
Contrast
Brightness
Color
1. Press the MENU button.
90
75
75
50
0
2. Select the Picture.
3. Press the CHxy buttons to select a picture item.
4. Press the VOLÏq buttons to adjust the picture
condition as you want.
Sharpness
Tint
5. Press the TV/AV button to store for the picture
User.
▲▼ ◀▶ MENUꢀꢀTV/AV
Selected Item
Contrast
Setting Change
More darkness VOLÏ 0~100 qVOL More light
Brightness
Color
Less bright VOLÏ 0~100 qVOL More bright
Lower color intensity VOLÏ 0~100 qVOL Higher color intensity
Soft picture VOLÏ 0~100 qVOL Hard picture
More purple VOLÏ 50~50 qVOL More green
Sharpness
Tint
PSM
TV/AV
CH
CH
VOL
VOL
Auto Picture Control
PSM (Picture Status Memory)
1. Press the PSM button.
2. Press the PSM button repeatedly to select [PSM].
Each press of the button changes the screen display as
below.
Dynamic → Standard → Mild → Game → User
• Dynamic : Vivid Picture Appearance
• Standard : Standard Picture Appearance
• Mild : Softer Picture Appearance
• Game : External Video Game Picture Setup
• User : Manual Picture Setup
17
Sound Control
You can select your preferred sound setting; Flat, Music,
Movie or Speech and you can also adjust the sound
frequency of equalizer, balance. If you switch AVL to on,
the set automatically keeps on an equal volume level even
if you change program.
Sound
Equalizer
Balance
AVL
▶
0
Off
Surround
nVolume
MTS
Off
0
1. Press the MENU button.
2. Select the Sound menu.
Mono
0
3. Press the CHxy button to select the desired sound
item; Equalizer, Balance, AVL, Surround or
Sub woofer
▲▼ ◀▶ MENUꢀTV/AV
n
Volume, MTS.
4. Press the VOLÏq button to make desired
adjustment.
5. Press the VOLÏq button in Equalizer to set the
Equalizer.
Equalizer
Flat
Music
Movie
Speech
User
0.1 0.5 1.5ꢀ 5.0ꢀꢀ10Khz
▲▼
MENUꢀTV/AV
PSM
TV/AV
CH
CH
6. Press the CHxy button to select your preferred setting ;
Flat, Music, Movie, Speech or User.
VOL
VOL
To set the Equalizer User.
a. Select User by pressing the CHxy button.
b. Select a sound band by pressing the VOLÏq button.
c. Make appropriate sound level with the CHxy button.
d. Press the MENU button to return to preceding MENU
and the TV/AV button to return to normal TV viewing.
7. Select the Balance menu and adjust the balance of speakers.
8. Select the AVL(Automatic Volume Leveler) menu On or Off
9. Select the Surround menu On or Off.
10. Select the nVolume menu and adjust the volume from
headphone.
11. Press the SAP button to select the desired sound item.
Each time you press the SAP buttons, the MTS is displayed
one by one as shown below.
Stereo → SAP → Mono
Auto Sound Control
SSM (Sound Status Memory)
1. Press the SSM button.
2. Press the SSM button repeatedly to select.
Each press of the button changes the screen display as below.
Flat → Music → Movie → Speech → User
18
Captions
Closed captioning is a process, which converts the audio portion of a television
program into written words, which then appear on the television screen in a form
similar to subtitles. Closed captions allow viewers to read the dialogue and narration
of television programs.
Using Closed Captions
Captions are the subtitles of the dialogue and narration of
television programs. For prerecorded programs, program
dialogue can be arranged into captions in advance. It’s
possible to caption a live program by using a process called
real-time captioning, which creates captions instantly.
Professional reporters using a machine shorthand system
and computer for translation into English normally do real-
time captioning.
Captioning is an effective system for the hearing-impaired,
and it can also aid in teaching language skills.
Shooting... Goal in.....
The picture at left shows a typical caption.
Poor reception conditions are encountered:
• IGNITION:
Picture may flutter, drift, and suffer from black spots or horizontal streaking. Usually
caused by interference from automobile ignition systems, neon lamps, electrical drills,
and other electrical appliances.
• GHOSTS:
Ghosts are caused when the TV signal splits and follows two paths. One is the direct
path and the other is reflected off tall buildings, hills or other objects. Changing the
direction or position of the antenna may improve reception.
• SNOW:
If your receiver is located at the weak, fringe area of a TV signal, your picture may be
marred by small dots. It may be necessary to install a special antenna to improve the
picture.
An old, bad, or illegally recorded tape is played.
Strong, random signals from a car or airplane interference with the TV signal.
The signal from the antenna is weak.
The program wasn't captioned when it was produced, transmitted or taped.
1. Press the MENU button.
2. Select the the Special menu
3. Press the CH xy buttons to select Caption menu.
Special
Input
TV
4. Press the VOL Ïqbutton, select the Caption mode.
5. Each time you press the VOLÏq buttons, the caption
mode is displayed one by one as shown below.
Auto Sleep
Blue back
Captions
Off
Off
Off
→ OFF ↔ CC1 ↔ CC2 ↔ CC3 ↔ CC4 →
↑
↓
▲▼ ◀▶ MENUꢀꢀTV/AV
← TEXT4 ↔ TEXT3 ↔ TEXT2 ↔ TEXT1 ←
6. Press the TV/AV button
* This TV is programmed to remember which mode it was last set to, even if you
switch the POWER off.
* To convert as below needs about 10 seconds. (Because time to read information
for conversion is quite long in contrast with the others.)
CC4
↔
TEXT1
↔
TEXT2
19
Parental Control
If used, this optional feature can “block” undesirable programming from appearing on the TV.
Note: Parental Control is not available in PC Mode. To block Computer inputs, use
the block AUX SOURCES option in the Parental Control menu in TV Mode; computer
inputs will not be available.
Parental Control offers the user a wide variety of options and settings that restrict or
“block” the programming that can appear on the TV. Parental control allows the user
the capability of defining which program rating they consider accept-able, to the
younger or more sensitive viewer. It can be preset and turned either on or off by the
user who specifies the secret 4-number code, the password. The number of hours
blocked are specified. General audience and children viewer blocks should both be
programmed into the TV’s memory. Viewer ratings are specified for both TV and the
motion picture industry; both rating systems should be used, for complete coverage.
The ratings are based on the ages of children.
Overview
To insure complete coverage for all TV programs, (movies and regular TV shows)
choose a rating for MPAA, from the selections below. AND choose ratings from the
TV Parental Guidelines Rating System on the next page, using the Age Block option
for General Audiences, and for Children. In addition to those, you may wish to add
additional restrictions from the Content Block menu. See the Parental Control menu,
and submenus example on the next page.
Things to Consider before Setting Up Parental Control
Determine which rating you consider acceptable to the viewer. (For example, if you
choose TV-PG, all more restrictive ratings will be automatically blocked; the viewer
will not be able to see: TV-PG, TV-14, or TV-MA rated programming.)
Do you want to block the auxiliary video source entirely? (Blocks the signal sent by
the equipment, such as a VCR, connected to the TV Audio/Video input jacks; in the
Aux. Block option.) Or leave unblocked, then choose allowable ratings.
Block program “Content” based on individual parameters such as: Strong Dialog,
Bad Language, Sex Scenes, Violence Scenes, or Fantasy Violence Scenes; in the
Content Blk option.
How many hours do you want Parental Control to be active? You can set the Hours
option for up to 99 hours.
Select a secret password; in the Set Password option. Use the number keys on the
remote. Don’t forget the password, it is the only way you can access the Parental
Control menu and change rating selections, or turn Parental Control off.
Do you want Parental Control to be active all the time? If not, you can turn it on or off
with the Lock On/Off option.
* You can set different Parental Control viewing restrictions for general
audiences and for children - - both can be active at the same time.
* Simply specifying one content block such as Sex Scenes, will not automatically
block another content in the programs from appearing.
* Even if you choose to leave the Aux inputs unblocked, the ratings you specify
will automatically restrict the programming that appears from the video sources.
* You cannot disable Parental Control by disconnecting the TV from power. Block
hours will automatically reset to the original block time setting specified if power
is disconnected.
20
Parental Control
1. Press the MENU button.
2. Select the Setup menu
3. Select the Parental Control.
4. Press the CHxy button to select.
5. Adjust each item with VOLÏq button
Parental control
Content BLK
Age Block
Aux. Block Sources Unblocked
General
Unblocked
General
Children
Unblocked
Unblocked
MPAA Unblocked
Language
Sex scenes
Violence
Unblocked
Unblocked
Unblocked
Unblocked
Unblocked
Age Block
content Bik
Set Hours
▶
▶
◀▶ 00Hours
F-Violence
No-Rating
Set Passward ◀▶ ToꢀSet
LockꢀOn/OffꢀMustꢀSetꢀHours
Parental Control
Selected Item
Setting Change
↔
Unblocked Blocked
↔
Aux. Block Source
↔
↔
↔
X
Unblocked G and Above PG and Above PG-13 and
MPAA
↔
↔
Above R and Above NC-17 and Above
Set Hours
00~99 hours
↔
On Off
Lock On/Off
Age Block
↔
↔
↔
↔
Unblocked TV-G and Above TV-PG and Above TV-14
General
and Above TV-MA
↔
↔
Children
Content Block
Dialog
Unblocked TV-Y and Above TV-Y7
↔
↔
Unblocked TV-PG and Above TV-14
↔
↔
↔
Unblocked TV-PG and Above TV-14 and Above TV-MA
Language
Sex Scenes
Violence
↔
↔
↔
Unblocked TV-PG and Above TV-14 and Above TV-MA
↔
↔
↔
Unblocked TV-PG and Above TV-14 and Above TV-MA
↔
Unblocked TV-Y7
F- Violence
No-Rating
↔
Unblocked Blocked
a. As shown above, with the Parental Control menu on-screen, use the UP arrow to
highlight an option like Content Block, then press the Right arrow.
b. Use the Up/Left/Right arrows to select and adjust or set the rating for an option.
For Sex Scenes for example, use the “From TV-PG” setting. (See the Mini Glossary,
Ratings Charts on this and the previous page for rating definitions.)
c. After you have selected and adjusted the parental control menu options to your
preferences:
- Set the hours you want Parental Control active.
- Set a 4-number password.
- Set the Lock On/Off option to either on or off.
* When the Parental Control menu is Lock On, PIP picture is scrambled.
21
Parental Control
INFORMATION
MOTION PICTURE ASSOCIATION OF USA (MPAA) RATING SYSTEM
Grade
Meaning
G
General Audiences Content not offensive to most viewers
Parental Guidance Content is such that parents may not want their
PG
Suggested
children to view the program.
Program is inappropriate for preteens, with a greater
degree of offensive material Suggested than a PG
rated program
Parental Guidance
Suggested
PG-13
R
Not for children under age 17. Strong elements of
Restricted viewing
sex and/or violence.
Not for children under age 17 under any
circumstances. Strong sexual content.
NC-17 Restricted Viewing
Hard Core Films
X
Same as NC-17 rating.
TV PARENTAL GUIDELINE RATING SYSTEM
Grade
Meaning
Considered suitable for all audiences; children may
watch unattended.
TV-G General Audience
Suggested Unsuitable for younger children, may
TV-PG Parental Guidance contain: Suggestive Dialog, Bad Language, Sex, and
Violence Scenes
Parents Strongly
Cautioned
Unsuitable for children under 14, may contain: Strong
Dialog, Bad Language, Sex, and Violence Scenes.
TV-14
Mature Audience
Only
Adults only, may contain: Strong Dialog, Bad
Language, Sex, and Violence Scenes.
TV-MA
CHILDREN’S CLASSIFICATIONS
Grade
Meaning
TV-Y
Children
Considered suitable for all children under 7 years old.
Considered suitable for children over 7, may contain
TV-Y7 Children 7 and over
Fantasy Violence Scenes.
22
Other functions
TV, VIDEO, COMPONENT, and
Special
Input
TV
S-VIDEO modes
Auto Sleep
Blue back
Captions
Off
Off
Off
(You can’t set PC ANALOG and PC DIGITAL mode in this
menu. Use the TV/AV button)
Inputs can be set for TV, VIDEO, COMPONENT or S-VIDEO
mode. VIDEO mode is used when a Video Cassette
Recorder (VCR), or other equipment is connected to the set.
Note: When a VCR is connected to the aerial socket the set
is used in TV mode. See the ‘Connection of external
equipment’ section.
▲▼ ◀▶ MENUꢀꢀTV/AV
1. Press the MENU button.
2. Select the Special menu.
3. Press the CH xybutton to select Input.
4. Press the VOLÏqbutton to select TV, VIDEO,
COMPONENT and S-VIDEO.
VIDEO: VIDEO OUT connected to the VIDEO socket of
the set.
COMPONENT: COMPONENT connected to the
COMPO-NENT INPUT socket of the set.
PSM
S-VIDEO: S-VIDEO VCR connected to the S-VIDEO
TV/AV
sockets of the set.
CH
CH
Alternatively you can select the TV, VIDEO, COMPONEN-T,
S-VIDEO, PC ANALOG and PC DIGITAL, DTV modes by
pressing the TV/AV button.
VOL
VOL
PC ANALOG: PC connected to the D-SUB in of the set.
PC DIGITAL: PC connected to the DVI in of the set.
DTV: DTV Set Top Box connected to the COMPONENT IN
of the set.
Auto sleep
If you select Auto sleep on the set will automatically
switch itself to standby mode approximately ten minutes
after a TV Channel stops broadcasting.
1. Press the MENU button, select the Special menu.
2. Press the CHxy button to select Auto sleep.
3. Press the VOLÏq button to select On.
4. Press the TV/AV button to return to normal TV viewing.
Blue back
Channel without signal appear in blue.
Auto wide (Aspect Ratio Control)
Press the ARC button to select a desired picture format.
Each press of the ARC button, selects Auto Wide, 16:9, 14:9, ZOOM, 1:1 and Auto
wide mode.
23
Other functions
Sleep timer
You don’t have to remember to switch the set off before
you go to sleep. The sleep timer automatically switches the
set to standby after the preset time elapses.
Press the SLEEP button to select the number of minutes.
The display will appear on the screen, followed by 0, 10,
20, 30, 60, 90, 120, 180 and 240. The timer begins to
count down from the number of minutes selected.
Note:
B
120
a. To view the remaining sleep time, press the SLEEP
button once.
b. To cancel the sleep time, Select 0 with the SLEEP button.
SAP
Press the SAP button.
You can select the Sound output system-Stereo, Mono and
SAP and the language during dual language broadcast.
PIP Function
Viewing the PIP picture
Press the PIP button. (Press the PIP button again, to
turn off PIP.)
PSM
TV/AV
CH
CH
Selecting the PIP picture mode
Press the MODE button to adjust the PIP picture mode.
Each press the MODE button, selects the 16:1, 9:1,
double window and multi picture mode.( Multi picture
mode is just available when the main picture is in AV
mode.)
VOL
VOL
Moving the PIP picture
Press the POSITION button to adjust the position of sub
picture in PIP mode.
Switching the main and PIP picture
Press the SWAP button to switch the main and sub
picture in PIP mode.
Viewing the external source input
Press the INPUT button to select the input source of sub
picture in PIP mode.
Press the CH xy button to select the Channel desired
in TV mode of sub picture.
24
External Equipment Connection
You can connect additional equipment, such as VCRs, camcorders etc. to your set.
Examples are shown below.
Antenna connection.
1. Connect RF out on the VCR to the Antenna input
on the rear of the TV
ANT.
2. Connect the antenna cable to the antenna in
jack on the VCR.
3. Use the TV/AV button to select TV mode.
4. Press the PLAY button on the VCR.
VCR
COMPONENT INPUT
1. Connect the COMPONENT video output sockets
(Y Cb Cr) of the COMPONENT to the
COMPONENT INPUT sockets of the set.
2. Connect the audio cable from the COMPONENT
to the COMPONENT INPUT sockets of the set.
3. Press the TV/AV button to select COMPONENT
mode.
4. Press the PLAY button on the DVD.
The COMPONENT playback picture appears on
the screen.
A/V INPUT
1. Connect the AV out jacks on of the VCR to A/V-
In jacks on the TV.
2. Press the TV/AV button to select VIDEO mode.
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the
screen.
Note : If you have a mono VCR, connect the audio
cable from the VCR to the L(MONO) socket of the
set.
25
External Equipment Connection
S-VIDEO Input
If using an S-VIDEO source, the picture quality will
be improved over a video source.
1. Connect the S-VIDEO output of a VCR to the
S-VIDEO input on the TV.
2. Connect the audio cables from the S-VIDEO
VCR to the L (MONO) R inputs on the TV.
3. Select S-VIDEO mode by pressing the TV/AV
button repeatedly.
ANT.
4. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
VCR
DTV Input
1. Connect the DTV video output sockets(Y,Pb, Pr)
of the DTV set top box to the COMPONENT
Input sockets of the set.
2. Connect the audio cable from the DTV set top
box to the Audio Input sockets of the set.
3. Press the TV/AV button to select DTV mode.
AUDIO OUT
DTV OUT
<DTV set top box>
Headphone jack
Headphone
DC24V
Insert the headphone plug to the
headphone jack on the TV.
ANT.
You can listen to thesound through
the headphone; no sound from the
speaker on the TV. To adjust the headphone volume,
use the Volume menu in the Sound menu.
Sub woofer
ANT.
DC24V
Sub woofer Out
Connect the cable of the sub woofer to
the sub woofer output on the TV.
You can listen to the bass well.
To adjust the bass volume, use the Sub woofer
menu in the sound menu.
26
Connecting PC as monitor
Contrast
Picture adjustment
x
You can adjust picture Contrast, Brightness,
Horizontal/Vertical position,Clock, Phase, Auto and Reset
as you prefer.
0
Ï
100
q
100
y
1. Press the TV/AV or TV/PC button to select the PC
mode.
2. Press the MENU button.
3. Press the CHxy button
to select the desired
picture item.
1024 X 768
AUTO
48.4KHz 60.0Hz
▲▼ ◀▶ MENUꢀꢀTV/AV
4. Press the VOLÏqbutton to make appropriate
adjustments.
Contrast
This function is to adjust picture to light/dark.
Brightness
This function is to adjust brightness of picture.
Temperature
Temperature is a measure of the warmth of the image
color.
Horizontal Position/Vertical Position
This function is to adjust picture to left/right and up/down
as you prefer.
PSM
TV/AV
CH
Clock
VOL
VOL
This function is to minimize any vertical bars or stripes
visible on the screen background. And the horizontal
screen size will also change.
CH
Phase
This function allows you to remove any horizontal noise
and clear or sharpen the image of characters.
Auto
This function is for the automatic adjustment of the
screen position, clock and clock phase. The displayed
image will disappear for a few seconds while the Auto-
configuration is in process
Note Some signal from some graphics boards may not
function properly. If the results are unsatisfactory, adjust
our monitor’s position, clock and clock phase manually.
Reset
This function allows you to return to the good picture
reproduction Programmed at the factory and cannot be
changed.
Contrast
x
0
Ï
100
q
100
Color
This function is to adjust intensity of the color.
y
1024 X 768
*
When DVI source is connected, Auto, Clock and
48.4KHz 60.0Hz
Phase don’t operate.
When DTV source is connected, you can adjust
*
▲▼ ◀▶ MENUꢀꢀTV/AV
picture Contrast, Brightness, Color, Temperature,
Horizontal Position/Vertical Position, Clock, Phase
and Reset as you prefer.
<The Picture adjustment of DTV mode>
27
Connecting PC as monitor
PC ANALOG(D-SUB) INPUT
1. Connect the PC ANALOG IN cable (D sub jack) from the monitor output
socket of the PC to the PC/DTV input socket of the set.
2. Connect the PC Audio IN cable from the PC to the PC Audio IN of the set.
3. Press the TV/AV or TV/PC button to select PC ANALOG IN mode.
4. Switch on the PC, and the
PC screen appears on the set.
DC24V
The set can be operated as
the PC monitor.
PC DIGITAL(DVI) INPUT
1. Connect the DVI of PC to
PC Audio IN
the DVI input on the TV.
PC Analog IN
PC Digital IN
2. Select PC-DIGITAL mode by
pressing the TV/AV button
repeatedly.
Resolution
Mode
Resolution
Horizontal frequency (KHz) Vertical frequency (Hz)
31.5 KHz
35 KHz
37.9 KHz
37.5 KHz
31.5 KHz
60 Hz
67 Hz
72 Hz
75 Hz
70 Hz
640X480
640X480
640X480
640X480
720X400
VGA
800X600
800X600
800X600
800X600
56 Hz
60 Hz
72 Hz
75 Hz
35.2 KHz
37.9 KHz
48.1 KHz
46.9 KHz
SVGA
1024X768
1024X768
1024X768
48.4 KHz
56.5 KHz
60.2 KHz
60 Hz
70 Hz
75 Hz
XGA
WXGA
1280X768
60 Hz
47.7 KHz
Note:
a. If possible, use the VESA 1,024x768@60Hz video mode to obtain the best
image quality for your LCD monitor. If used under the other resolutions,
some scaled or processed pictures may appear on the screen. The set has
been preadjusted to the mode VESA 1,024x 768 @60Hz.
b. Some dot defects may appear on the screen, like Red, Green or Blue
spots.However, this will have no impact or effect on the monitor
performance.
28
Product Spec.
Model
LT-30 FMP
Horizontal size 850 mm
Thickness 210 mm
Main body
Height
485 mm
Weight 15 kg
Power requirements
DC 24V/6.0A
NTSC
Television system
Television program
LCD PANEL
VHF: 2~13 UHF: 14~69 Cable: 01~125
30” WIDE TFT LCD panel
WXGA(1280 X 768)
Resolustion
Power consumption
MAX. 130W
External antenna impedance 75Ω
Audio output
10W + 10W
• DVI 1
• S-VIDEO IN 1
• HEADPHONE JACK 1
• PC IN 1
External IN/OUT ports
• PC AUDIO IN 1
• COMPONENT 1
• POWER IN 1
• ANTENNA IN 1
• SUB WOOFER OUT 1
AC Power Adaptor
AC 100-240V, 50/60Hz 24Vdc, 6.0A
29
Troubleshooting
Problem
Check item
• Insert the AC power cord plug securely in AC power outlet.
• Make sure the remote control is not in the standby
mode (The POWER/Standby indicator is red.)
No picture on screen and no sound
from speakers.
• Check the brightness setting of the display.
• Lamp may have malfunction.
• Make sure a cable with no VIDEO input signal is
connected to the S-VIDEO INPUT terminal.
No picture/No picture from AV
terminal.
• Check the sound setting.
• Make sure the sound is not muted.
• Make sure the connectors of the optional speaker
system are securely inserted.
Picture is displayed, but no sound
from the speakers.
• Make sure the setting of AV OUTPUT terminal
• Make sure COLOR and CONTRAST settings.
Picture is too light
Picture is too dark.
• Make sure BRIGHTNESS setting is not set too low.
• Check to see if BRIGHTNESS setting
• Lamp may have malfunction.
• Change the batteries.
• Make sure the infrared transmitter window is not
receiving strong light such as light from fluorescent
lamps.
Remote control does not work.
• The reception may be weak.
The picture is not sharp.
The picture moves.
• The state of the broadcast may also be bad.
• Make sure the antenna is facing the right direction.
• Make sure the outside antenna is not disconnected.
• Make sure the antenna is facing the right direction.
• There may be reflected electric waves from
mountains or buildings.
The picture is doubled or tripled.
The picture is spotted.
• There may be interference from automobiles, trains,
high voltage lines, neon lights, etc.
• There may be interference between the antenna cable
and power cable. Try positioning them further apart.
• Is the unit receiving interference from other devices?
Transmission antennas of radio broadcasting stations
and transmission antennas of amateur radios and
cellular phones may also cause interference.
There are stripes on the screen or
colors fade.
• Use the unit as far apart as possible from devices
that may cause possible interference.
30
LIMITED WARRANTY
31
|