Life is good Computer Monitor L226WU User Manual

User’s Guide  
L226WU  
Make sure to read the Important Precautions before using the product.  
Keep the User's Guide(CD) in an accessible place for future reference.  
See the label attached on the product and give the information to your  
dealer when you ask for service.  
Important Precaautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place the  
display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,  
laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release of  
heat generated during operation. If these openings are blocked, built-up heat can  
cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal  
The fluorescent lamp used in this product contains a small amount of mercury.  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
A2  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Connecting the stand base  
1
Place the monitor with its front facing downward on a cushion or soft cloth.  
2.  
.
Rotate the Stand Body as shown in figure  
.
1
1
3
Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.  
Once assembled take the monitor up carefully and face the front side  
4.  
.
Stand Base  
Stand Body  
Warning  
The tape and locking pin may only be removed from those monitors equipped with a standing base  
when the base is pulled up.  
Otherwise, you may be injured by the protruding sections of the stand.  
A3  
Connecting the Display  
Disassembling the stand  
1. Put a cushion or soft cloth on aflat  
2. Place the monitor face Down on  
surface.  
the cushion or soft cloth.  
3. Pushing Latch inside, Take the stand base from stand body.  
Important  
This illustration depicts the general model of connection. Your monitor may differ from the items  
shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may fall and get  
damaged or injure your foot.  
A4  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Positioning your display  
1.  
Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range : -3˚~17˚  
Swivel :356˚  
Height Range : maximum 5 .51 inch (140.0mm)  
140.0mm  
* Please be sure to  
remove the Locking  
pin to adjust the height.  
Ergonomic  
It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward  
tilt angle of the monitor should not exceed 5 degrees.  
You do not need to replace the Locking pin after it is removed, to adjust its height.  
A5  
Connecting the Display  
Using the Computer  
1. Make sure to turn off the computer and product.  
2
1
Connect signal input cable  
screw of the signal cable.  
and power cable  
in order, then tighten the  
A
B
C
Connect DVI Cable  
Connect D-sub Cable  
Connect USB Cable  
Analog signal Digital signal  
D-sub DVI  
Power Cord  
USB  
AC-IN  
D-SUB  
DVI-D  
Wall-outlet type  
PC-outlet type  
C
B
DVI-D(This feature is notAavailable in all countries.)  
2. Press  
button on the front switch panel to turn the power on.  
When monitor power is turned on, the 'Self Image Setting  
Function' is executed automatically.  
(Only Analog Mode)  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user  
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual  
input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push the  
AUTO/SET’ button on the front panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on the  
OSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.  
A6  
Use USB programs  
Connecting the USB(Universal Serial Bus) Cable  
1.  
Plug in the USB cable as in the diagram.  
One USB Upstream port  
Two USB Downstream ports  
Connect to downstream connectors of desktop or  
laptop computers, mouse, memory stick or USB  
hard disk. (However, the computer must support  
USB and have the USB port.)  
AC-IN  
D-SUB  
DVI-D  
Tidying USB (Universal Serial Bus) Cable  
1.  
Elevate the monitor as far as possible follow  
the arrow to rotate, and plug the USB cable  
into the monitor.  
2.  
Tidy the USB cable as in the diagram,  
press(follow the arrow) the cable holder,  
and open it.  
3.  
Fit the USB cable into the cable holder as in  
the diagram.  
When connecting multi screens  
A7  
Use USB programs  
Use USB programs  
The display feature can be used by easily connecting the USB cable between  
laptops/desktops and the USB port at the back of the monitor.  
System Requirements  
In order to make full use of USB Display features, your computer must meet the following minimum  
system requirements:  
1.2 GHz CPU or higher, 512 MB memory or higher (Recommended Specifications: 1.6  
GHz Core2 Duo CPU, 1 GB memory)  
USB 2.0 Interface  
Windows 2000 (Service Pack 4), Windows XP (Service Pack 2) Operating Systems (O/S)  
are supported. (But, Windows 98, ME, NT, Vista, Macintosh, Linux Operating Systems  
(O/S) are not supported.)  
1. Connect the USB cable as shown in the picture and press the 'SOURCE' button on the front of the  
monitor to select the main display.  
2. “LG USB Easy Connection” driver installation automatically starts.  
Before installation, make sure your computer meets the minimum system requirements of Windows  
2000 (Service Pack 4) and Windows XP (Service Pack 2). If your computer fails to meet those  
When the “LG USB Easy Connection” program does not install automatically, please install the driver  
manually as shown below.  
3
1
4
6
2
5
If your computer fails to meet the system requirements, the warning message "DisplayLink Core  
Software" will be displayed. Press the [OK] button, and continue to install "LG USB Easy Connection"  
program.  
3. Install "LG USB Easy Connection" program as the instruction message says, fully remove the USB cable,  
and then reboot your computer. Without rebooting, "LG USB Easy Connection" will not operate properly.  
For more detailed information on installation and removal, refer to the accompanied <LG USB Easy  
Connection Installation Guide>.  
A8  
Use USB programs  
4. When the installation of "LG USB Easy Connection" program  
is completed, icons as shown in the picture will be created in  
the taskbar. With these icons, you can easily use features  
such as Screen Resolution, Color Quality, Screen Rotation,  
Extend To, Extend and Mirror.  
Color Quality : You can choose 16  
bit or 32 bit colors.  
Screen Resolution : Provides information on the  
resolution that the USB supports.  
Screen Rotation : You can set the direction to display USB images. (Pivot function)  
When there is an input USB signal, you can use Pivot programs on GUI.  
1. Lift the monitor to its highest height to utilize the Pivot function.  
Head  
o
section  
2. Landscape & Portrait : You can rotate the panel 90 clockwise.  
Please be cautious and avoid contact between the monitor  
head and the Stand Base when rotating the screen to access  
the Pivot function.  
Stand  
If the monitor head touches the Stand Base, then the Stand  
section  
Base could crack.  
3. When rotating the monitor, be careful with the connected cables.  
A9  
Use USB programs  
Extend To : Sets the location to display USB images.  
(1: Standard monitor, 3: USB Monitor)  
Left  
Right  
Below  
Above  
Extend : Expands the display to a sub screen.  
Mirror : Shows the same display as the main screen.  
Off : Does not to display data to make sure USB  
screen is not displayed.  
5. When using multiple USB monitors, you can set "LG USB Easy Connection" program  
separately for each monitor.  
Select No. 3 USB monitor and use "LG USB Easy  
Connection" features.  
2
In case of USB dual monitors.  
1
NOTE  
In a monitor to monitor connection, with one USB up to five are possible with direction connection, and up to six are  
possible with parallel connection.  
With the USB cable unconnected, you will not have any trouble using the PC.  
Monitor and USB Display connectors support USB 2.0 High Speed.  
Does not support DOS game (StarCraft) and other 3D games.  
For more information on USB, visit the following web site.(http://www.usb.org)  
‘LG USB Easy Connection’ program may be changed without notice for the purpose of product improvement.  
A10  
Control Panel Functions  
Front Panel Controls  
6
You can select the computer that you want to use by  
selecting input signal (DVI, D-Sub or USB).  
The default input signal is analogue (D-Sub).  
SOURCE Button  
MENU Button  
Use this button to enter or exit the On Screen Display.  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control  
settings, so that they cannot be inadvertently changed.  
Press and hold the MENU button for several seconds.  
The message "OSD LOCKED" should appear.  
You can unlock the OSD controls at any time by pushing  
the MENU button for several seconds. The message  
"OSD UNLOCKED" should appear.  
A11  
Control Panel Functions  
Use these buttons to select or adjust functions in the On  
Screen Display.  
-
+
Buttons  
For more information, refer to page A19.  
Use this button to enter a selection in the On Screen  
Display.  
AUTO/SET  
Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press  
the AUTO/SET button before entering the On Screen  
Display(OSD). This will automatically adjust your  
display image to the ideal settings for the current  
screen resolution size (display mode).  
The best display mode is  
-
22 inch monitor : 1680 x 1050  
Use this button to turn the display on or off.  
Power Button  
This Indicator lights up blue when the display operates  
normally(On Mode). If the display is in Sleep Mode  
(Energy Saving), this indicator color changes  
to amber.  
Power Indicator  
A12  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating parameters of  
the display is quick and easy with the On Screen Display Control system.  
A short example is given below to familiarize you with the use of the controls.  
The following section is an outline of the available adjustments and selections  
you can make using the OSD.  
NOTE  
Allow the display to stabilize for at least 30 minutes before making image adjustments.  
To make adjustments in the On Screen Display, follow these steps:  
AUTO/SET  
MENU  
MENU  
+
+
-
-
Press the MENU Button, then the main menu of the OSD appears.  
To access a control, use the - or + Buttons. When the icon you want  
becomes highlighted, press the AUTO/SET Button.  
Use the - /+ Buttons to adjust the image to the desired level. Use the  
AUTO/SET Button to select other sub-menu items.  
Push the MENU Button once to return to the main menu to select another  
function. Push the MENU Button twice to exit from the OSD.  
A13  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
Main menu  
Sub-menu  
BRIGHTNESS  
CONTRAST  
GAMMA  
A
D
USB  
Reference  
PICTURE  
To adjust the brightness,  
contrast and gamma of  
the screen  
sRGB  
6500K  
9300K  
To customize the color  
of the screen  
COLOR  
PRESET  
RED  
GREEN  
BLUE  
HORIZONTAL  
VERTICAL  
CLOCK  
PHASE  
To adjust the position  
of the screen  
POSITION  
To improve the clarity  
TRACKING  
and stability of the screen  
SHARPNESS  
LANGUAGE  
SETUP  
To customize the screen  
status for a user's  
OSD  
HORIZONTAL  
operating environment  
POSITION VERTICAL  
WHITE BALANCE  
POWER INDICATOR  
FACTORY RESET  
ARC  
FLATRON  
F-ENGINE  
MOVIE / TEXT  
USER  
To select or customize  
desired image settings  
NORMAL  
: Adjustable  
A : Analog Input  
D : Digital Input  
USB: Digital Input  
NOTE  
The order of icons may differ depending on the model (A14~A19).  
A14  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MENU Button, then the main menu of the OSD appears.  
Menu Name  
P I C T U R E  
Sub-menus  
Icons  
Button Tip  
MENU  
: Exit  
: Adjust (Decrease/Increase)  
: Enter  
: Select another sub-menu  
+
-
SET  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
A15  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
PICTURE  
P I C T U R E  
To adjust the brightness of the screen.  
To adjust the contrast of the screen.  
BRIGHTNESS  
CONTRAST  
GAMMA  
Set your own gamma value. : -50/0/50  
On the monitor, high gamma values  
display whitish images and low gamma  
values display high contrast images.  
MENU : Exit  
-
: Decrease  
: Increase  
+
SET : Select another sub-menu  
COLOR  
C O L O R  
Select the screen color.  
PRESET  
• sRGB: Set the screen color to fit the  
SRGB standard color  
specification.  
• 6500K: Slightly reddish white.  
• 9300K: Slightly bluish white.  
Set your own red color levels.  
Set your own green color levels.  
Set your own blue color levels.  
RED  
MENU : Exit  
GREEN  
BLUE  
-
: Decrease  
: Increase  
+
SET : Select another  
sub-menu  
A16  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
POSITION  
P O S I T I O N  
To move image left and right.  
To move image up and down.  
HORIZONTAL  
VERTICAL  
MENU : Exit  
-
: Decrease  
+
: Increase  
SET : Select another sub-menu  
TRACKING  
T R A C K I N G  
CLOCK  
To minimize any vertical bars or stripes  
visible on the screen background.  
The horizontal screen size will also  
change.  
PHASE  
To adjust the focus of the display.  
This item allows you to remove any  
horizontal noise and clear or sharpen  
the image of characters.  
MENU : Exit  
-
: Decrease  
: Increase  
SHARPNESS To adjust the clearness of the screen.  
+
SET : Select another sub-menu  
A17  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To choose the language in which the  
control names are displayed.  
LANGUAGE  
SETUP  
OSD  
To adjust position of the OSD window  
on the screen.  
POSITION  
S E T U P  
WHITE  
If the output of the video card is different  
the required specifications, the color level  
may deteriorate due to video signal  
distortion. Using this function, the signal  
level is adjusted to fit into the standard  
output level of the video card in order to  
provide the optimal image.  
BALANCE  
Activate this function when white and  
S E T U P  
black colors are present in the screen.  
Use this function to set the power  
indicator on the front side of the monitor  
to ON or OFF.  
POWER  
INDICATOR  
If you set OFF, it will go off.  
If you set ON at any time, the power  
indicator will automatically be turned on.  
4:3 IN WIDE  
To select the image size of the screen.  
MENU : Exit  
-
: Adjust  
+
: Adjust  
SET : Select another  
sub-menu  
WIDE  
4:3  
4:3 : Depending on the input video signal ratio,  
it is automatically changed to an optimized  
screen ratio. (The 1280X1024 input signal is  
changed to 5:4 ratio and 1024X768 to 4:3.)  
Resolution  
Screen ratio  
1280x1024  
1152x864  
1024x768  
800x600  
640x480  
720x480  
5 : 4  
4 : 3  
4 : 3  
4 : 3  
4 : 3  
3 : 2  
The input signal which the 4:3 IN WIDE does not  
support '4:3' is the following.  
-
The 22 inch monitor is  
720x400,1280x768,1360x768,1440x900 1680x1050  
Restore all factory default settings except  
FACTORY  
RESET  
"LANGUAGE."  
Press the  
button to reset immediately.  
+
If this does not improve the screen image, restore the factory default settings.  
If necessary, perform the white balance function again. This function will be enabled only when  
the input signal is an analog signal.  
A18  
On Screen Display(OSD) Selection and Adjustment  
The OSD screen will appear when you touch the  
button on the front of  
the monitor.  
Menu Name  
Icons  
Sub-menu Name  
FLATRON F-ENGINE  
Screen when applied Screen when not applied  
When you execute F-ENGINE, two tones will appear  
on the screen as shown. The applied screen will  
appear on the left side, whereas the non-applied  
screen will appear on the right side.Touch the SET  
button to use the adjusted screen.  
Main menu  
Sub menu  
Description  
This feature lets you easily select the best desired  
image condition optimized to the environment  
(ambient illumination, image types etc).  
MOVIE  
TEXT  
MOVIE: For animation images in videos or movies  
TEXT: For text images (Word processing etc.)  
MENU : Exit  
,
: Move  
+
-
SET : Select  
USER User  
You can manually adjust brightness, ACE or RCM.  
You can save or restore the adjusted value even  
when using a different environment.  
To adjust the USER sub-menu function,  
...  
(Brightness): Adjusts screen brightness.  
Press the SET Button  
...  
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.  
...  
RCM(Real Color Management): Selects the color mode.  
0
Not applied  
1
Green enhance  
2
Flesh tone  
Color Enhance  
3
SAVE  
Select the  
sub-menu using the SET button  
MENU : Exit  
and save the YES value using the buttons.  
: Decrease  
-
+
: Increase  
SET : Select another sub-menu  
NORMAL  
This is under normal operating conditions.  
A19  
Troubleshooting  
Check the following before calling for service.  
No image appears  
Is the power cord of the  
Check and see if the power cord is connected  
properly to the power outlet.  
display connected?  
Is the power on and the  
power indicator blue or  
green?  
Adjust the brightness and the contrast.  
Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
amber?  
• Try to turn on the PC  
.
Do you see an "OUT OF  
RANGE" message on  
the screen?  
This message appears when the signal from the  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
This message appears when the signal cable  
between your PC and your display is not  
Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
connected. Check the signal cable and try again.  
Do you see a "OSD LOCKED" message on the screen?  
Do you see “OSD  
LOCKED” when you  
push MENU button?  
• You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
“OSD UNLOCKED” will appear.  
A20  
Troubleshooting  
Display image is incorrect  
Display Position is  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, adjust the image  
position using the H position and V position icon  
in the on screen display.  
incorrect.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
vertical bars or stripes using the CLOCK icon in  
the on screen display.  
On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
horizontal bars using the PHASE icon in the on  
screen display.  
Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
portrayed.  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
Important  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
Reasons for Recommending Optimal Resolution : The aspect ratio is 16:10.  
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might encounter  
problems such as blurred letters, blurry screen, cut-off screen display or tilted  
screen.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer  
.
A21  
Troubleshooting  
Display image is incorrect  
The screen color is  
Check if the signal cable is properly connected  
and use a screwdriver to fasten if necessary.  
Make sure the video card is properly inserted in  
the slot.  
mono or abnormal.  
Set the color setting higher than 24 bits (true color)  
at Control Panel - Settings.  
Check if the screen is set to interlace mode and if  
yes, change it to the recommend resolution.  
The screen blinks.  
Have you installed the display driver?  
Have you installed the  
display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette) that comes with your  
display. Or, you can also download the driver from  
Make sure to check if the video card supports  
Plug&Play function.  
Do you see an  
"Unrecognized monitor,  
Plug&Play (VESA DDC)  
monitor found"  
message?  
A22  
Specifications  
Display  
22 inches (55.868 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
22 inches viewable  
0.282*0.282 mm pixel pitch  
Horizontal Freq.  
28 - 83 kHz (Automatic)  
Sync Input  
Video Input  
Vertical Freq.  
Analog : 56 - 75 Hz (Automatic)  
Digital, USB : 60 Hz (Automatic)  
Input Form  
Separate Sync.  
SOG (Sync On Green)  
Digital (HDCP)  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
USB Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Digital, USB  
Max  
Recommend  
DDC 2B  
VESA 1680 x 1050 @60 Hz  
VESA 1680 x 1050 @60 Hz  
Resolution  
Plug&Play  
:
45 W(Typ.)  
2 W  
2 W  
Power  
On Mode  
Sleep Mode  
Consumption  
Off Mode  
Dimensions  
& Weight  
With Stand  
Without Stand  
Width  
Height  
Depth  
50.17 cm / 19.75 inches 50.17 cm / 19.75 inches  
43.00 cm / 16.93 inches 37.14 cm / 14.62 inches  
25.11 cm / 9.89 inches  
6.00 cm / 2.36 inches  
Net  
6.2 kg (13.78 lbs)  
Tilt  
-3˚~17˚ (Head)  
Range  
Height  
Swivel  
Rotation  
5.51inch (140.0mm)  
356˚  
90˚ clockwise  
AC 100-240V~ 50/60Hz 1.2A  
Operating Conditions  
Power Input  
Environmental  
Conditions  
Temperature  
10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20˚C to 60 ˚C  
5 % to 90 % non-Condensing  
A23  
Specifications  
Stand Base  
Power cord  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
Standard  
Data Rate  
USB 2.0, Self-Power  
Max 480 Mbps  
USB  
Power Consumption Max 2.5W x 2  
NOTE  
Information in this document is subject to change without notice.  
A24  
Specifications  
Preset Modes (Resolution)  
Analog,Digital supporting modes  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
720 x 400  
640 x 480  
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
64.674  
65.290  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
3
640 x 480  
4
800 x 600  
5
800 x 600  
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1680 x 1050  
7
8
9
10  
11  
*12  
*Recommend Mode  
USB supporting mode  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
640 x 480  
720 X 400  
800 x 600  
31.469  
31.468  
37.879  
49.727  
48.363  
67.500  
63.681  
60.000  
63.981  
55.469  
65.290  
60  
70  
60  
75  
60  
75  
75  
60  
60  
60  
60  
1
2
3
4
832 x 624  
5
1024 x 768  
1152 x 864  
1152 X 870  
1280 x 960  
1280 x 1024  
1440 x 900  
1680 x 1050  
6
7
8
9
10  
11  
Indicator  
LED Color  
MODE  
blue  
amber  
Off  
On Mode  
Sleep Mode  
Off Mode  
A25  
Installing the Wall mount plate  
This monitor satisfies the specifications of the Wall mount plate or  
the interchange device.  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Separate the stand using a screwdriver as shown in the picture.  
3. Install the Wall mount plate.  
Wall mount plate(Separate purchase)  
This is stand-type or wall mount type and is  
connectable with Wall mount plate.  
Please refer to the installation guide for more  
details, which is provided when Wall mount  
plate is purchased.  
Kensington Security Slot  
Connected to a locking cable that can be  
purchased separately at most computer stores.  
A26  
Digitally yours  

Intel 631xESB User Manual
JVC XV MK5GSL User Manual
Lenovo Computer Monitor 9352 User Manual
LG Electronics LG Life Good Computer Monitor W2361VG User Manual
Maytag Cooktop JEC7430AA User Manual
Mitel INT1400 User Manual
Nortel Networks Nortel IP Phone 1110 User Manual
Philips 24PW8504 User Manual
Philips DVP3254KX User Manual
Philips SE6551B User Manual