PLASMA MONITOR
OWNER’S MANUAL
MODELS : MU-50PZ44/44M/44V
MU-50PZ44A/44MA/44VA
MU-50PZ44B/44MB/44VB
MU-50PZ44K/44MK/44VK
MU-50PZ44R/44MR/44VR
MU-50PZ44S/44MS/44VS
MU-50PZ90/90M/90V
MU-50PZ90A/90MA/90VA
MU-50PZ90B/90MB/90VB
MU-50PZ90K/90MK/90VK
MU-50PZ90R/90MR/90VR
MU-50PZ90S/90MS/90VS
Please read this owner’s manual thoroughly before operating
the Monitor.
Retain it for future reference.
Record model number and serial number of the Monitor.
See the label attached on the back of the Monitor and relate
this information to your dealer if you ever require service.
Model Number :
Serial Number :
a
P/NO : 3828VA0410A (RF03GB)
Warning
Warning
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
FCC NOTICE
• A Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
• Any changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
2
Plasma Monitor
Safety Instructions
Safety Instructions
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential elec-
trical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and
observe the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation
that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian StandardsAssociation.
1. Read Instructions
9. Attachments
All the safety and operating instructions should be read
before the product is operated.
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
2. Follow Instructions
10. Ventilation
All operating and use instructions should be followed.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by plac-
ing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is pro-
vided or the manufacturer’s instructions have been adhered
to.
3. Retain Instructions
The safety and operating instructions should be retained for
future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.
5. Cleaning
11. Power Sources
Unplug this product from the wall outlet before cleaning. Do This product should be operated only from the type of power
not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
6. Water and Moisture
Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub, in a wet base-
ment, or near a swimming pool.
12. Power-Cord Polarization
This product is equipped with a three-wire grounding type
plug, a plug having a third (grounding) pin. This plug will only
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or on fit into the grounding-type power outlet. This is a safety fea-
an unstable cart, stand, tripod, bracket, or table. The product
may slide or fall, causing serious injury to a child or adult,
and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manu-
facturer, or sold with the product. Any mounting of the prod-
uct should follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the manufac-
turer.
ture. If you are unable to insert the plug into the outlet, con-
tact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.
8. Transporting Product
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
PORTABLE CART WARNING
Owner’s Manual
3
Safety Instructions
Safety Instructions continued
14. Outdoor Antenna Grounding
19. Servicing
If an outside antenna or cable system is connected to the Do not attempt to service this product yourself as opening or
product, be sure the antenna or cable system is grounded so
as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical
Code (U.S.A.), ANSI/ NFPA 70 provides information with
regard to proper grounding of the mast and supporting struc-
ture, grounding of the lead-in wire to an antenna discharge
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service per-
sonnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
unit, size of grounding conductors, location of antenna-dis- qualified service personnel under the following conditions:
charge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
Example of Grounding According to National
Electrical Code Instructions
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been
damaged.
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Electric Service
Equipment
f. If the product exhibits a distinct change in performance.
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
21. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the man-
ufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
NEC - National Electrical Code
15. Lightning
For added protection for this product (receiver) during a light- shock, or other hazards.
ning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect 22. Safety Check
the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to deter-
mine that the product is in proper operating condition.
16. Power Lines
An outside antenna system should not be located in the 23. Wall or Ceiling Mounting
vicinity of overhead power lines or other electric light or
The product should be mounted to a wall or ceiling only as
power circuits, or where it can fall into such power lines or recommended by the manufacturer. The product may slide
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
or fall, causing serious injury to a child or adult, and serious
damage to the product.
24. Heat
17. Overloading
The product should be situated away from heat sources
Do not overload wall outlets and extension cords as this can such as radiators, heat registers, stoves, or other products
result in a risk of fire or electric shock.
(including amplifiers) that produce heat.
18. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
4
Plasma Monitor
Contents
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4
Screen Menu Options
Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .20
Setting Picture Format . . . . . . . . . . . . . . . . . . .20
Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .20
Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Screen Position . . . . . . . . . . . . . . . . . . . . . . . .21
Manual Configure . . . . . . . . . . . . . . . . . . . . . . .21
Screen Adjustments . . . . . . . . . . . . . . . . . . . . .22
Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Selecting Wide VGA/XGA mode . . . . . . . . . . . .22
Luminance Noise Reduction . . . . . . . . . . . . . . .22
PIP (Picture-in-Picture) Feature
Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23
PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .23
Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23
Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Selecting an Input Signal Source for PIP . . . . . .23
Twin Picture Setup Options
Introduction
Controls and Connection Options . . . . . . . . . . . .7
Remote Control Key Functions . . . . . . . . . . . . . .8
Installation
Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10
External Equipment Connections . . . . . . . . . .11~14
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11
External A/V Source Setup . . . . . . . . . . . . . . . .12
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14
Operation
Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .15
Menu Language Selection . . . . . . . . . . . . . . . . . .15
Video Menu Options
APC (Auto Picture Control) . . . . . . . . . . . . . . . .16
Manual Picture Control . . . . . . . . . . . . . . . . . . .16
Auto Color Temperature Control . . . . . . . . . . . .16
Manual Color Temperature Control . . . . . . . . . .16
Audio Menu Options
DASP (Digital Auto Sound Processing) . . . . . . .17
Manual Sound Control . . . . . . . . . . . . . . . . . . .17
AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17
Time Menu Options
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .18
On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .18
Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Special Menu Options
Watching Twin Picture . . . . . . . . . . . . . . . . . . . .24
Sub Picture Size Adjustment . . . . . . . . . . . . . . .24
Swapping the Twin Picture . . . . . . . . . . . . . . . .24
Selecting a Source for the Twin Picture . . . . . . .24
External Control Device Setup . . . . . . . . . . . . . . . .25~30
IR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31~32
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .33
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Menu Rotation For Vertical Viewing . . . . . . . . . .19
Setup and Operation Checklist
Setup and Operation Checklist
(See pages 11~13 for available connection and operational setup options.)
1. Unpack Monitor and all accessories.
5. Turn video source equipment on.
2. Connect all external video and audio equipment.
see pages 11 ~ 14.
6. Select viewing source for Monitor.
See page 8.
3 Install batteries in remote control.
See page 8.
7. Fine-tune source image and sound to personal preference
or as required by source.
See pages 16 ~ 17.
4. Turn Monitor on.
See page 15.
8. Additional features Setup
See Contents above.
After reading this manual, keep it handy for future reference.
Owner’s Manual
5
Introduction
Introduction
What is a Plasma Display Panel (PDP)?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that
instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is
clear and visible to viewers anywhere in the room.
Wide Screen
The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture
feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would
not fit.
The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen
The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell
defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be accept-
able. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective.
Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed
to minimize cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with
cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operat-
ing and cooling the PDP.
The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the
operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not suffi-
cient cause for the PDP to be exchanged or returned.
6
Plasma Monitor
Introduction
Controls
Front Panel Controls
- This is a simplified representation of front panel.
Here shown may be somewhat different from your monitor.
ON/OFF
INPUT SELECT
MENU
VOL.
E, D Buttons
VOLUME (F,G) Buttons
Main Power Button
INPUT SELECT Button
MENU Button
Remote Control Sensor
Power Standby Indicator
Illuminates red in standby mode,
Illuminates green when the
Monitor is turned on.
Connection Options
Back Connection Panel
- Connection panels shown may be somewhat different from your monitor.
Y
PB
PR
AUDIO L (MONO)
AUDIO
L
R
R
(
)
(
)
(
)
(
)
R
L
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
DVI INPUT
RGB INPUT AUDIO INPUT RGB OUTPUT
AUDIO INPUT
COMPONENT INPUT
S-VIDEO
VIDEO INPUT AUDIO INPUT
AC INPUT
EXTERNAL SPEAKER
1
2
3
4
5
6
7
8
1. EXTERNAL SPEAKER (8 ohm output)
5. REMOTE CONTROL
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker
Connect your wired remote control to the remote control
port on the Monitor.
Stand’ manual.
6. COMPONENT INPUT/AUDIO INPUT JACKS
2. RS-232C INPUT (CONTROL/SERVICE) PORT
Connect a component video/audio device to these jacks.
Connect to the RS-232C port on a PC.
7. S-VIDEO INPUTS
3. DVI (Digital Visual Interface) INPUT/
RGB INPUT/AUDIO INPUT JACKS
Connect the monitor output connector from a PC to the
appropriate input port.
Connect S-Video out from an S-VIDEO VCR to the S-VIDEO
input.
AUDIO/VIDEO INPUT JACKS
Connect audio/video out from external equipment to these
jacks.
4. RGB OUTPUT PORT
You can watch the RGB signal on another monitor, connect
RGB OUTPUT to another monitor’s PC input port.
8. POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is indi-
cated on the Specifications page. Never attempt to operate
the Monitor on DC power.
Owner’s Manual
7
Introduction
Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the monitor.
- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press
the key again as necessary.
POWER
Switches the Monitor between
INPUT SELECT
Selects source: Video, S-Video,
ON and STANDBY.
SLEEP
Sets the Sleep Timer.
(Refer to p.18)
RGB, DVI, or Component mode.
POWER
SLEEP
DASP
INPUT SELECT
To select the sound appropriate to
your viewing program character:
Flat, Music, Cinema, Sports, or
User (Refer to p.17)
APC
Adjusts the factory preset picture
according to the room.
APC
ARC
DASP
PIP ARC
(Refer to p.16)
PIP
TWIN PICTURE
SUB INPUT
MUTE
PIP ARC
Changes the PIP picture format.
(Refer to p.23)
ARC
Changes the picture format.
(Refer to p.20)
SWAP
MENU
TWIN PICTURE
(Refer to p.24)
PIP
Switches the sub picture on or off.
(Refer to p.23)
OK
VOL
VOL
SUB INPUT
Selects the input source for the sub
picture.
SWAP
Exchanges main and sub picture
images. (Refer to p.23, 24)
MUTE
Switches the sound on or off.
1
4
7
2
5
8
0
3
6
9
MENU
Displays on screen menus one by one.
Exits the current menu.
OK
D / E
Selects menu option.
NUMBER buttons
Memorizes menu changes.
F / G (Volume button)
Increases/decreases sound level.
Adjusts menu settings.
WIN. SIZE
Adjusts the sub picture size.
POWER
REW
STOP
PLAY
P/STILL
FF
WIN.POSITION
REC
Moves the sub picture.
VCR BUTTONS
Control some video cassette
recorders.
WIN.SIZE WIN.POSITION SPLIT ZOOM
SPLIT ZOOM
ZOOM -
ZOOM +
Enlarges the picture.
ZOOM-/ZOOM+
Enlarges or reduces
the main picture size.
Installing Batteries
• Open the battery compartment cover on the back side and
insert the batteries with correct polarity.
• Install two 1.5V batteries of AAA type. Don’t mix used batteries
with new batteries.
8
Plasma Monitor
Installation
Installation
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer
where you purchased the product.
POWER
SLEEP
INPUT SELECT
APC
ARC
DASP
PIP ARC
PIP
TWIN PICTURE
SUB INPUT
MUTE
SWAP
MENU
OK
VOL
VOL
1
4
7
2
5
8
0
3
6
9
POWER
REW
STOP
PLAY
P/STILL
1.5V
FF
REC
WIN.SIZE WIN.POSITION SPLIT ZOOM
ZOOM
-
ZOOM
+
Owner’s Manual
Batteries
BNC-RCA Adapter
Remote Control
D-sub 15 pin Cable
Power Cord
DVI-D Cable
Installation Instructions
• The Monitor can be installed in various ways such as on a wall, or on a desktop etc.
• The plasma display is designed to be mounted horizontally or vertically. The speakers shown are optional.
GROUNDING
Power
Supply
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
Short-circuit
Breaker
unit by connecting it to telephone wires, lightening rods, or gas pipes.
Wall Mount: Horizontal installation
For proper ventilation, allow a clearance of 4” on each
side and 2” from the wall. Detailed installation instruc-
tions are available from your dealer, see the optional
Wall Mounting Bracket Installation and Setup Guide.
2
inches
4 inches
4 inches
4 inches
4 inches
Owner’s Manual
9
Installation
Installation Instructions continued
Desktop Pedestal Installation
For proper ventilation, allow a clearance of 4” on each
side and the top, 2.36” on the bottom, and 2” from the
wall. Detailed installation instructions are included in the
optional Desktop Stand Installation and Setup Guide
available from your dealer.
4 inches
2
inches
4 inches
4 inches
2.36 inches
Wall Mount: Vertical installation (MU-50PZ44M/44V/90M/90V series models only)
Detailed installation instructions are included in the
optional Vertical Wall Mounting Bracket Installation and
Setup Guide available from your dealer.
NOTE: When installing the monitor vertically, the front
panel controls must be in the left side position.
When installing the monitor vertically, you
have to change the OSD display mode so
that the menus will appear correctly and also
to protect the monitor from overheating
(Refer to P. 19).
10 Plasma Monitor
Installation
External Equipment Connections
NOTE: Not all cables shown are included with the plasma display.
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor
- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still
picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen.
How to connect
1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO
INPUT.
2. Connect the audio and video cables from the VCR's output jacks to
the monitor input jacks, as shown in the figure.
Y
PB
PR
AUDIO L (MONO)
AUDIO
L
R
R
When connecting the monitor to VCR, match the jack colors (Video
= yellow, Audio Left = white, and Audio Right = red).
AUDIO INPUT COMPONENT INPUT
S-VIDEO VIDEO INPUT AUDIO INPUT
Mono VCR: Connect the video output cable from the VCR to the
VIDEO input on the monitor.
S-VIDEO VCR: Connect the S-Video output cable from the VCR to
the S-VIDEO input on the monitor. (Note that S-Video offers higher
quality).
How to use
1. Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
2. Use the INPUT SELECT button on the remote control to select
Video.
(If connected to S-VIDEO, select the S-Video input source.)
S-VIDEO
OUT
IN
VCR
(R) AUDIO (L)
VIDEO
Cable TV Setup
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.
The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.
- For further information regarding cable TV service, contact your local cable TV service provider(s).
How to connect
1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO
INPUT.
2. Connect the audio and video cables from the Cable Box's output
jacks to the monitor input jacks, as shown in the figure.
When connecting the monitor to a Cable Box, match the jack colors
Y
P
B
PR
AUDIO L (MONO)
AUDIO
L
R
R
(Video = yellow, Audio Left = white, and Audio Right = red).
AUDIO INPUT
COMPONENT INPUT
S-VIDEO VIDEO INPUT AUDIO INPUT
How to use
1. Use the INPUT SELECT button on the remote control to select
Video.
2. Select your desired channel with the remote control for cable box.
(R) AUDIO (L) VIDEO
TV
VCR
RF
Cable
Cable Box
Owner’s Manual 11
Installation
External A/V Source Setup
How to connect
1. Connect the provided BNC-RCA adapter to the monitor’s
VIDEO INPUT.
Y
P
B
PR
AUDIO L (MONO)
2. Connect the audio and video cables from the external
equipment's output jacks to the monitor input jacks, as
shown in the figure.
AUDIO
L
R
R
AUDIO INPUT
S-VIDEO VIDEO INPUT AUDIO INPUT
COMPONENT INPUT
When connecting the monitor to external equipment, match
the jack colors (Video = yellow, Audio Left = white, and
Audio Right = red).
Camcorder
How to use
1. Use the INPUT SELECT button on the remote control to
select Video.
Video Game Set
2. Operate the corresponding external equipment. Refer to
external equipment operating guide.
AUDIO
VIDEO
R
L
DVD Setup
How to connect
1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR)
INPUT jacks and connect the DVD audio outputs to the AUDIO
INPUT jacks on the monitor, as shown in the figure.
Y
PB
PR
AUDIO L (MONO)
AUDIO
L
R
R
2. If your DVD only has an S-Video output jack, connect this to the
S-VIDEO input on the monitor and connect the DVD audio outputs
to the AUDIO INPUT jacks on the monitor, as shown in the figure.
AUDIO INPUT COMPONENT INPUT
S-VIDEO VIDEO INPUT AUDIO INPUT
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT SELECT button on the remote control to select
Component. (If connected to S-VIDEO, select the S-Video exter-
nal input source.)
3. Refer to the DVD player's manual for operating instructions.
• Component Input ports
To get better picture quality, connect a DVD player to the compo-
nent input ports as shown below.
or
(R) AUDIO (L)
B
(R) AUDIO (L)
R
S-VIDEO
DVD
Component ports of the
Y
PB
PR
Monitor
Pr
R-Y
Cr
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Video output ports
of DVD player
PR
DTV Setup
- To watch digitally broadcast programs, purchase and
connect a digital set-top box.
- This monitor supports HDCP (High-bandwidth Digital
Contents Protection) protocol for DVI DTV
(480p,720p,1080i) mode.
Y
P
B
PR
AUDIO L (MONO)
AUDIO
L
R
R
REMOTE
CONTROL
DVI INPUT
RGB INPUT AUDIO INPUT RGB OUTPUT
AUDIO INPUT
COMPONENT INPUT
S-VIDEO
VIDEO INPUT AUDIO INPUT
How to connect
Use the monitor’s COMPONENT (Y, PB, PR) INPUT,
RGB or DVI jack for video connections, depending on
your set-top box connector. Then, make the corre-
sponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner’s
manual for the digital set-top box.)
2. Use INPUT SELECT on the remote control to select
Component, RGB, or DVI.
or
or
(R) AUDIO (L)
(R) AUDIO (L)
RGB-DTV OUTPUT
(R) AUDIO (L)
B
R
DVI-DTV OUTPUT
Digital Set-top Box
12 Plasma Monitor
Installation
PC Setup
- This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends
configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel
(DDC) protocol.
- The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning
rate for the graphic card.
How to connect
1. To get the best picture quality, adjust the PC
graphics card to a 1024x768, 60Hz. Resolutions
(
)
(
)
(
)
(
)
over UXGA cannot be displayed.
R
L
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
2. Use the monitor’s RGB INPUT or DVI (Digital
Visual Interface) INPUT port for video connections,
depending on your PC connector.
RGB INPUT
DVI INPUT
AUDIO INPUT RGB OUTPUT
EXTERNAL SPEAKER
If the graphic card on the PC does not output ana-
log and digital RGB simultaneously, connect only
one of either RGB INPUT or DVI INPUT to display
the PC on the monitor.
If the graphic card on the PC does output analog
and digital RGB simultaneously, set the monitor to
either RGB or DVI; (the other mode is set to Plug
and Play automatically by the monitor.)
3. Then, make the corresponding audio connections.
If using a sound card, adjust the PC sound as
required.
How to use
1. Turn on the PC and the monitor.
2. Turn on the display by pressing the POWER button on the monitor's remote control.
3. Use the INPUT SELECT button on the remote control to select RGB or DVI.
4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC
graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable.
• Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become
permanently imprinted on the screen. Use the Orbiter screen saver when possible.
• The synchronization input form for Horizontal and Vertical frequencies is separate.
Owner’s Manual 13
Installation
Monitor Display Specifications (RGB-PC / DVI-PC Mode)
Horizontal
Vertical
Horizontal
Vertical
Resolution
Resolution
Frequency(KHz) Frequency(Hz)
Frequency(KHz) Frequency(Hz)
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
35.156
37.879
46.875
53.674
49.725
31.500
35.000
37.500
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
56.25
60.31
75.00
85.06
74.55
60.00
70.00
75.00
60.00
70.00
75.00
60.00
70.06
75.02
60.05
70.01
75.00
60.00
60.02
60.00
75.02
60.00
75.02
31.500
35.000
37.500
48.363
56.476
60.023
54.348
63.995
67.500
60.000
63.981
47.700
59.625
47.700
59.625
640x350
852x480
720x400
1024x768
1152x864
640x480
1280x960
1280x1024
800x600
1360x768
1366x768
832x624
848x480
14 Plasma Monitor
Operation
Operation
Turning on the Monitor
Turning on the Monitor just after installation
1. Connect power cord correctly.
2. Press the
ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby
mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT
button on the remote control and then the Monitor will switch on.
Turning on the Monitor (power cord is still connected)
1. If the Monitor was turned off with the
ON/OFF button on the Monitor
• Press the ON/OFF button on the Monitor to turn the Monitor on.
2. If the Monitor was turned off with the remote control and then the
ON/OFF button on the Monitor
• Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the
Monitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on.
Menu Language Selection
- The menus can be shown on the screen in the selected language. First select your language.
1. Press the MENU button and then use D
button to select the SPECIAL menu.
E
/
VIDEO
AUDIO
TIME
Language
G
English
Key lock
2. Press the G button and then use D
button to select Language.
E
Español
Português
Français
/
ISM Method
Low power
Set ID.
3. Press the G button and then use D E button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your choice.
OSD Rotate
/
SPECIAL
SCREEN
TWIN
4. Press the OK button to save.
MENU
Prev.
Owner’s Manual 15
Operation
Video Menu Options
- Video menu adjustment are unique to each input source. Readjust Video menu settings for each following
input source as preferred.
• RGB (PC) / DVI (PC),
• RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i)
• Video / S-Video / Component (480i)
APC (Auto Picture Control)
- APC adjusts the Monitor for the best picture appearance.
- When adjusting Video menu options (contrast, brightness, color, sharpness, and tint) manually, APC automatically
changes to User.
1. Press the APC button repeatedly to select the picture appearance setup option as shown below.
Clear
Optimum
Soft
User
• You can also adjust APC in the VIDEO menu.
•
Clear, Optimum, and Soft settings are preset for optimum picture quality at the factory and cannot be changed.
Manual Picture Control (User option)
- You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer.
VIDEO
AUDIO
TIME
APC
1. Press the MENU button and then use D / E button to select the VIDEO menu.
ACC
Color temp.
2. Press the G button and then use
button to select the desired picture option
/ E
D
Contrast
85 G
Brightness
Color
60
50
50
0
(Contrast, Brightness, Color, Sharpness, or Tint).
3. Press the G button and then use F / G button to make appropriate adjustments.
4. Press the OK button to save.
SPECIAL
Sharpness
Tint
SCREEN
TWIN
MENU Prev.
Auto Color Temperature Control
- To initialize values (reset to default settings), select the Normal option.
- When adjusting color temperature options (red, green, and blue) manually, ACC automatically changes to User.
1. Press the MENU button and then use D / E button to select the VIDEO menu.
VIDEO
AUDIO
TIME
APC
ACC
G
Normal
Cool
2. Press the G button and then use D / E button to select ACC .
Color temp.
Contrast
Brightness
Color
Warm
User
85
60
50
50
0
3. Press the G button and then use D / E button to select either Normal (Default), Cool
(Preset), Warm (Preset), or User (Manual Adjustment).
SPECIAL
Sharpness
Tint
SCREEN
TWIN
4. Press the OK button to save.
MENU Prev.
Manual Color Temperature Control (User option)
- You can adjust red, green, and blue to any color temperature you prefer.
1. Press the MENU button and then use D / E button to select the VIDEO menu.
VIDEO
AUDIO
TIME
APC
ACC
2. Press the G button and then use D / E button to select the Color temp .
Color temp.
G
Red
0
0
0
Contrast
Brightness
Color
85
60
50
50
0
Green
Blue
3. Press the G button and then use D / E button to select Red, Green, or Blue.
SPECIAL
Sharpness
Tint
4. Use the F / G button to make appropriate adjustments.
SCREEN
TWIN
• The adjustment range for Red, Green, and Blue is -20 ~ +20.
MENU Prev.
5. Press the OK button to save.
16 Plasma Monitor
Operation
Audio Menu Options
DASP (Digital Auto Sound Processing)
- DASP lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate
sound options based on the program content.
- When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to User.
1. Press the DASP button repeatedly to select the appropriate sound setup as shown below.
Flat
Music
Cinema
Sports
User
• You can also adjust DASP in the AUDIO menu.
•
Flat, Music, Cinema and Sports are preset for good sound quality at the factory and cannot be
changed.
Manual Sound Control (User option)
DASP
AVL
VIDEO
AUDIO
TIME
1. Press the MENU button and then use D / E button to select the AUDIO menu.
Balance
0
2. Press the G button and then use
button to select the desired sound option
/ E
D
Treble
Bass
50 G
50
(Balance, Treble, or Bass).
SPECIAL
3. Press the G button and then use F / G button to make appropriate adjustments.
SCREEN
TWIN
4. Press the OK button to save.
MENU Prev.
AVL (Auto Volume Leveler)
- This feature maintains an equal volume level; even if you change channels.
VIDEO
AUDIO
TIME
1. Press the MENU button and then use D / E button to select the AUDIO menu.
DASP
AVL
G
On
Off
2. Press the G button and then use D / E button to select AV L .
Balance
Treble
Bass
0
50
50
3. Press the G button and then use D / E button to select On or Off.
SPECIAL
4. Press the OK button to save.
SCREEN
TWIN
MENU Prev.
Owner’s Manual 17
Operation
Time Menu Options
Clock Setup
- If current time setting is wrong, reset the clock.
1. Press the MENU button and then use D / E button to select the TIME menu.
2. Press the G button and then use D / E button to select Clock.
3. Press the G button and then use D / E button to set the hour.
VIDEO
AUDIO
TIME
Clock
G
--
:
--
Off timer
On timer
Auto off
SPECIAL
4. Press the G button and then use D / E button to set the minutes.
SCREEN
TWIN
5. Press the OK button to save.
MENU Prev.
On/Off Timer Setup
- Timer function operates only if current time has been already set.
- Off-Timer function overrides On-Timer function if they are set to the same time.
1. Press the MENU button and then use D / E button to select the TIME menu.
VIDEO
AUDIO
TIME
Clock
2. Press the G button and then use D / E button to select Off timer or On timer.
Off timer
On timer
Auto off
G
On
Off
3. Press the G button and then use D / E button to select On.
12
00
30
:
• To cancel On/Off timer function, select Off.
SPECIAL
Vol.
SCREEN
TWIN
4. Press the G button and then use D / E button to set the hour.
MENU Prev.
5. Press the G button and then use D / E button to set the minutes.
6. For only On timer function; Press the G button and then use D / E button to set
volume level.
7. Press the OK button to save.
Auto Off
- If there is no input signal, the Monitor turns off automatically after 10 minutes.
1. Press the MENU button and then use D / E button to select the TIME menu.
VIDEO
AUDIO
TIME
Clock
Off timer
On timer
2. Press the G button and then use D / E button to select Auto off.
Auto off
G
On
Off
3. Press the G button and then use D / E button to select On or Off.
SPECIAL
4. Press the OK button to save.
SCREEN
TWIN
MENU Prev.
Sleep Timer
- The sleep timer turns the Monitor off at a preset time. Note that this setting is cleared when the monitor is turned off.
z
1. Press the SLEEP button repeatedly to select the number of minutes. First the
z --- Min option appears on the
screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to count
down from the number of minutes selected.
3. To check the remaining minutes before the monitor turns off, press the SLEEP or OK button once.
z
4. To cancel the Sleep Timer, press the SLEEP button repeatedly until
z--- Min appears.
18 Plasma Monitor
Operation
Special Menu Options
Key Lock
- The monitor can be set up so that it can only be used with the remote control.
- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.
- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.
1. Press the MENU button and then use D / E button to select the SPECIAL menu.
VIDEO
Language
Key lock
G
On
Off
AUDIO
2. Press the G button and then use D / E button to select Key lock.
ISM Method
Low power
Set ID.
TIME
3. Press the G button and then use D / E button to select On or Off.
OSD Rotate
SPECIAL
W
• When you select On, the display ‘
on the front panel is pressed.
Key lock’ appears on the screen if any button
SCREEN
TWIN
MENU
Prev.
4. Press the OK button to save.
-In setting Key lock ‘On’, if the monitor is turned off with the remote control, press the INPUT SELECT button
on the monitor or POWER, INPUT SELECT on the remote control to turn the monitor on.
ISM (Image Sticking Minimization) Method
- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost
image remaining; even when you change the image. Avoid allowing a fixed image to remain on the Monitor's
screen for a long period of time.
VIDEO
Language
1. Press the MENU button and then use D / E button to select the SPECIAL menu.
Key lock
AUDIO
TIME
Normal
ISM Method
G
2. Press the G button and then use D / E button to select ISM Method.
White wash
Orbiter
Low power
Set ID.
Inversion
SPECIAL
OSD Rotate
3. Press the G button and then use D / E button to select either Normal, White wash,
Orbiter, or Inversion.
SCREEN
TWIN
• Normal
MENU
Prev.
If image sticking is never a problem, ISM is not necessary - set to Normal.
• White wash
White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear
entirely with White Wash. To return to normal viewing, press the any button.
• Orbiter
Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid
a permanent image on the screen, the image will move every 1 minutes: Right → Right → Downside → Downside → Left
→ Left → Upside → Upside.
• Inversion
Inversion will automatically invert the plasma display panel color every 30 minutes.
4. Press the OK button to save.
Low Power
VIDEO
- Low power reduces the plasma display's power consumption.
Language
AUDIO
TIME
Key lock
ISM Method
1. Press the MENU button and then use D / E button to select the SPECIAL menu.
2. Press the G button and then use D / E button to select Low power.
3. Press the G button and then use D / E button to select On or Off.
Low power
G
On
Off
Set ID.
SPECIAL
OSD Rotate
SCREEN
TWIN
MENU
Prev.
• When you select On, the screen darkens.
4. Press the OK button to save.
Menu Rotation for Vertical Viewing (MU-50PZ44M/44V/90M/90V series models only)
VIDEO
1. Press the MENU button and then use the D / E button to select the SPECIAL menu.
Language
Key lock
AUDIO
2. Press the G button and then use the D / E button to select OSD Rotate.
ISM Method
Low power
Set ID.
TIME
3. Press the G button and then use the D / E button to select Normal or Rotate.
• Select Normal, if the monitor was installed horizontally.
• Select Rotate, if the monitor was installed vertically.
SPECIAL
OSD Rotate
G
Normal
Rotate
SCREEN
TWIN
MENU
Prev.
4. Press the OK button to save.
Owner’s Manual 19
Operation
Screen Menu Options
Auto Adjustment
- RGB (PC) mode only; This function doesn’t work for RGB-DTV.
- Automatically adjusts picture position and minimizes image shaking.
- After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.
- The Auto config. and Manual config. are not active in DVI mode.
1. Press the MENU button and then use D / E button to select the SCREEN menu.
VIDEO
Auto config.
ARC
G
To set
AUDIO
2. Press the G button and then use D / E button to select Auto config..
Zoom in/out
Position
TIME
Manual config.
3. Press the G button to run Auto configure.
Screen adj.
SPECIAL
Reset
• When Auto config. has finished, OK will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment again.
XGA Mode
SCREEN
TWIN
MENU Prev.
4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config.,
you can make further adjustments with the Manual config. option.
Setting Picture Format
- Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.
- Set every aspect ratio for RGB 480p, DVI 480p, Component 480i/480p, Video, and S-Video sources.
- Use 4:3, or 16:9 for other input sources.
1. Press the ARC button repeatedly to select the desired picture format. You can also adjust ARC in the SCREEN
menu.
• 4:3
- Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both
the left and right sides.
• 16:9
- Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.
• Horizon
- Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both
sides, to create a spectacular view.
• Zoom
- Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions
of the picture will be cropped.
Picture Size Zoom
- When enlarging or reducing the picture, the image may become distorted.
1. Use ZOOM+/ZOOM- button to enlarge or reduce the picture size.
• Zoom adjustment range is 100~300.
2. Adjust the main picture position using the D / E / F / G buttons while in enlarged picture mode.
Zoom out
100%
D
F
G
E
20 Plasma Monitor
Operation
Split Zoom
- Enlarges the picture in correct proportions.
- Split Zoom can be used for all input sources.
- In 2-Split Zoom mode, you can only move the image up or down.
- If a screen is enlarged, a screen can move without selecting section of screen Split Zoom.
- It’s not available to use this function if OSD Rotate is set to the Rotate option.
1. Press the SPLIT ZOOM button repeatedly to select either 2, 4 , or 9 Split Zoom.
9-Split zoom
4-Split zoom
2-Split zoom
▲
▼
1
4
7
2
5
8
3
6
9
▲
▼
▲
▼
1
4
2
5
1
4
◀
▶
◀
▶
◀
▶
2. Press the number button corresponding to the section you wish to enlarge. You can move within the enlarged
image with the D / E / F / G button. To return to normal viewing, press the SPLIT ZOOM button again.
Section 5 is enlarged to fill
the screen.
Example of choosing 5.
9-Split zoom
▲
▼
1
4
7
2
5
8
3
6
9
◀
▶
Screen Position
- This function works in the following mode:
RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i).
1. Press the MENU button and then use D / E button to select the SCREEN menu.
VIDEO
AUDIO
TIME
Auto config.
ARC
2. Press the G button and then use D / E button to select Position.
3. Press the G button and then use D / E / F / G button to adjust the position.
4. Press the OK button to save.
Zoom in/out
▲
Position
G
◀
▶
▼
Manual config.
Screen adj.
Reset
SPECIAL
SCREEN
TWIN
XGA Mode
MENU Prev.
Manual Configure (RGB-PC mode only)
- If the image still isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture
Phase manually.
- To correct the screen size, adjust Clock.
1. Press the MENU button and then use D / E button to select the SCREEN menu.
VIDEO
Auto config.
2. Press the G button and then use D / E button to select Manual config..
3. Press the G button and then use D / E button to to select Phase or Clock.
4. Use the F / G button to make appropriate adjustments.
AUDIO
TIME
ARC
Zoom in/out
Position
0
0
Manual config.
G
Phase
Clock
SPECIAL
Screen adj.
Reset
SCREEN
TWIN
XGA Mode
• The Phase adjustment range is 0 ~ 31.
• The Clock adjustment range is -50 ~ +50.
MENU Prev.
5. Press the OK button to save.
Owner’s Manual 21
Operation
Screen Menu Options continued
Screen Adjustments (Video, S-Video and Component 480i mode only)
- Use this function to correct jittering or picture instability while viewing a video tape.
1. Press the MENU button and then use D / E button to select the SCREEN menu.
2. Press the G button and then use D / E button to select Screen adj..
3. Press the G button and then use D / E button to to select TV or VCR.
VIDEO
AUDIO
TIME
Auto config.
ARC
Zoom in/out
Position
Manual config.
SPECIAL
Screen adj.
G
TV
• Select the VCR option if watching a VCR.
• Select the TV option for other equipment.(Except VCR)
VCR
Reset
YNR
SCREEN
TWIN
MENU Prev.
4. Press the OK button to save.
Initializing (Reset to original factory value)
- This function operates in every mode.
- To initialize the adjusted value
VIDEO
AUDIO
TIME
1. Press the MENU button and then use D / E button to select the SCREEN menu.
2. Press the G button and then use D / E button to select Reset.
3. Press the G button.
Auto config.
ARC
Zoom in/out
Position
Manual config.
Screen adj.
SPECIAL
• You can initialize Zoom In/Out, Manual config., Position, Split zoom, PIP size, PIP posi-
tion and sub picture size for twin picture.
To set
Reset
G
SCREEN
TWIN
XGA Mode
MENU Prev.
Selecting Wide VGA/XGA mode (RGB-PC, DVI-PC mode only)
- To see a normal picture, match the resolution of RGB XGA mode (1024x768, 1360x768, 1366x768) with the selection for XGA
mode and the resolution of RGB VGA mode (640x480, 848x480, 852x480) with the selection for VGA mode in the SCREEN
menu.
- If the input source is RGB VGA mode, the screen menu option is changed from XGA mode to VGA mode automatically.
VIDEO
1. Press the MENU button and then use D / E button to select the SCREEN menu.
AUDIO
Auto config.
2. Press the G button and then use D / E button to select VGA mode/XGA mode.
ARC
TIME
Zoom in/out
3. Press the G button and then use D / E button to select the desired VGA/XGA resolution.
Position
SPECIAL
SCREEN
TWIN
Manual config.
Screen adj.
Reset
1024x768
1360x768
1366x768
4. Press the OK button to save.
XGA Mode
G
MENU Prev.
Luminance Noise Reduction (Video, S-Video and Component 480i modes only)
- Use YNR to reduce the picture noise which may appear on the screen.
VIDEO
AUDIO
TIME
1. Press the MENU button and then use D / E button to select the SCREEN menu.
Auto config.
ARC
2. Press the G button and then use D / E button to select YNR.
Zoom in/out
Position
3. Press the G button and then use D / E button to select On or Off.
SPECIAL
Manual config.
Screen adj.
Reset
4. Press the OK button to save.
On
Off
SCREEN
TWIN
YNR
G
MENU Prev.
22 Plasma Monitor
Operation
PIP (Picture-In-Picture) Feature
- PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the
other source will show a smaller inset image.
PIP Size
Watching PIP
Press the WIN.SIZE button and then use F / G button to
Press the PIP button repeatedly to turn PIP on or off.
change the sub picture size.
Component
Video
10 : 30
Win.size
F
G
PIP Aspect Ratio
Swapping the PIP
Press the PIP ARC button. The sub picture appears as shown.
Press the SWAP button to switch the main and sub pictures.
Component
Video
Video
Component
10 : 30
10 : 30
16 :
9
4 :
3
Main Picture
Sub Picture
Moving the PIP
Press the WIN.POSITION button.
Press the D / E / F / G button repeatedly until desired posi-
tion is achieved. The sub picture moves up/down/left/right.
Win.position
▲
◀
▶
▼
Selecting an Input Signal Source for the PIP
Use the SUB INPUT button to select the input source for
the sub picture.
Available Sub Picture Sources
Main Picture Source
Video
S-Video, Component 480i/480p/720p/1080i, RGB, and DVI
Video, Component 480i/480p/720p/1080i, RGB, and DVI
Video,S-Video, RGB, and DVI
Video and S-Video
Component 480i, Video, and S-Video
S-Video
Component 480i
Component 480p/720p/1080i
RGB and DVI
Owner’s Manual 23
Operation
Twin Picture Setup Option
- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the
same time. Each source is given half the screen.
Watching Twin Picture
Press the TWIN PICTURE button repeatedly to select one of the Twin Picture options.
DW 1
DW 2
Sub Picture Size Adjustment
Press the WIN.SIZE button and then use F / G button to change the sub picture size.
• Using the WIN.SIZE function in Twin Picture mode, main and sub picture sizes are
changed simultaneously.
Using the WIN.SIZE function in PIP mode, sub picture size is changed.
• WIN.POSITION is not functional in Twin Picture mode.
Win.size
G
F
Swapping the Twin Picture
Use the SWAP button to switch the main and sub pictures in twin picture mode.
Component
Video
Video
Component
10 : 30
10 : 30
Main Picture
Sub Picture
Selecting a Source for the Twin Picture
Use the SUB INPUT button to select the input source for the sub picture.
Available Sub Picture Sources
Main Picture Source
Video
S-Video, Component 480i/480p/720p/1080i, RGB, and DVI
Video, Component 480i/480p/720p/1080i, RGB, and DVI
Video,S-Video, RGB, and DVI
Video and S-Video
Component 480i, Video, and S-Video
S-Video
Component 480i
Component 480p/720p/1080i
RGB and DVI
24 Plasma Monitor
External Control Device Setup
External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the Monitor’s functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
- RS-232C connection cables are not supplied with the Monitor.
Y
PB
PR
AUDIO L (MONO)
AUDIO
L
R
R
(
)
(
)
(
)
(
)
R
L
RS-232C INPUT
(CONTROL/SERVICE)
REMOTE
CONTROL
DVI INPUT
RGB INPUT AUDIO INPUT RGB OUTPUT
AUDIO INPUT
COMPONENT INPUT
S-VIDEO
VIDEO INPUT AUDIO INPUT
AC INPUT
EXTERNAL SPEAKER
Type of Connector: D-Sub 9-pin Male
No. Pin Name
1
5
1
2
3
4
5
6
7
8
9
No Connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
9
6
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
RS-232C Configurations
3- Wire Configuration
(Not standard)
7-Wire Configuration
(Standard RS-232C cable)
PC
PDP
PC
PDP
TXD
RXD
GND
DTR
DSR
RTS
CTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
2
3
5
4
6
7
8
3
2
5
6
4
8
7
2
3
5
4
6
7
8
3
2
5
4
6
7
8
TXD
GND
DTR
DSR
RTS
CTS
D-Sub 9
D-Sub 9
D-Sub 9
D-Sub 9
Owner’s Manual 25
External Control Device Setup
Set ID
- Use this function to specify a monitor ID number.
- Refer to ‘Real Data Mapping 1’. See page 27.
1. Press the MENU button and then use the D / E button to select the SPECIAL menu.
VIDEO
AUDIO
TIME
Language
Key lock
2. Press the G button and then use D / E button to select Set ID..
ISM Method
Low power
3. Press the G button and then use F / G button to adjust Set ID. to choose the desired
monitor ID number.
Set ID.
G
1
SPECIAL
OSD Rotate
SCREEN
TWIN
• The adjustment range of Set ID. is 1 ~ 99.
MENU
Prev.
Communication Parameters
• Baud rate : 115200 bps (UART)
• Data length : 8 bits
• Stop bit : 1 bit
• Communication code : ASCII code
• Parity : None
Command Reference List
Transmission / Receiving Protocol
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
01. Power
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
a
b
c
d
e
f
0 ~ 1
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
0 ~ 4
[Command 1]: k, j
[Command 2]: To control PDP set.
*
*
*
0 ~ 3
[Set ID]: You can adjust the set ID to choose desired moni-
tor ID number in Special menu. Adjustment range
is 1 ~ 99. When selecting Set ID ‘0’, every con-
nected PDP set is controlled. Set ID is indicated
as decimal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
[DATA]: To transmit command data.
0 ~ 1
0 ~ 1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 1
g
h
i
08. Brightness
09. Color
*
*
*
10. Tint
j
Transmit ‘FF’ data to read status of command.
[Cr]: Carriage Return
11. Sharpness
k
l
ASCII code ‘0x0D’
12. OSD Select
13. Remote Control Lock Mode
14. PIP/Twin
[
]: ASCII code ‘space (0x20)’
m
n
o
p
q
r
0 ~ 1
0 ~ 3
15. PIP Aspect Ratio
16. Split Zoom
0 ~ 1
21 ~99
0 ~ 3
OK Acknowledgement
17. PIP Position
18. Treble
[Command2][ ][Set ID][ ][OK][Data][x]
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 3
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
19. Bass
s
t
20. Balance
21. Color Temperature
22. Red Adjustment
23. Green Adjustment
24. Blue Adjustment
25. PIP Input Source
26. Abnormal State
27. ISM Method
28. Low Power
u
v
w
$
y
z
p
q
r
0 ~ C8
0 ~ C8
0 ~ C8
0 ~ 4
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
0 ~ a
0 ~ 3
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
j
0 ~ 1
29. Orbiter Time Setting
30. Orbiter Pixel Setting
31. Picture Size Setting
for Twin Picture mode
32. Auto Configure
j
1 ~ FE
0 ~9
j
s
t
Data 1: Illegal Code
2: Not supported function
3: Wait more time
j
0 ~64
j
u
1
• Menu doesn’t display on screen when setting the 4,
12, 13, and 26 ~ 32.
26 Plasma Monitor
External Control Device Setup
04. Screen Mute (Command2:d)
01. Power (Command2:a)
G To control Power On/Off of the Monitor.
Transmission
GTo select screen mute on/off.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
1 : Power On
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Acknowledgement
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
GTo show Power On/Off.
Transmission
05. Volume Mute (Command2:e)
[k][a][ ][Set ID][ ][FF][Cr]
GTo control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Data 0 : Power Off
1 : Power On
Acknowledgement
Transmission
[a][ ][Set ID][ ][OK][Data][x]
[k][e][ ][Set ID][ ][Data][Cr]
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback
presents status about each function.
Data 0 : Volume mute on (Volume off)
1 : Volume mute off (Volume on)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
02. Input Select (Command2:b) (Main Picture Input)
G To select input source for the Monitor.
06. Volume Control (Command2:f)
You can also select an input source using the INPUT
GTo adjust volume.
SELECT button on the Monitor's remote control.
You can also adjust volume with the volume buttons
on remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Transmission
Data 0 : RGB
1 : Component
3 : S-video
4 : DVI
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
2 : Video
• Refer to ‘Real data mapping1’ as shown below.
Acknowledgement
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast (Command2:g)
03. Aspect Ratio (Command2:c) (Main picture format)
G To adjust screen contrast.
GTo adjust the screen format.
You can also adjust contrast in the Video menu.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Special menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Transmission
Data Min : 0 ~ Max : 64
[k][c][ ][Set ID][ ][Data][Cr]
• Refer to ‘Real data mapping1’ as shown below.
Acknowledgement
Data 0 : Wide screen (16:9)
1 : Normal screen (4:3)
2 : Full screen (Zoom)
3 : Horizon
[g][ ][Set ID][ ][OK][Data][x]
Acknowledgement
Real data mapping 1
*
[c][ ][Set ID][ ][OK][Data][x]
0 : Step 0
* You select either 16:9 or 4:3 screen aspect ratio using the
PC, DTV 720p/1080i.
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
64 : Step 100
Owner’s Manual 27
External Control Device Setup
08. Brightness (Command2:h)
13. Remote Control Lock Mode (Command2:m)
G To adjust screen brightness.
G To lock the remote control and front panel controls on the
You can also adjust brightness in the Video menu.
monitor
Transmission
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
[k][m][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
Data 0: Lock off
1: Lock on
• Refer to ‘Real data mapping 1’. See page 27.
Acknowledgement
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
[h][ ][Set ID][ ][OK][Data][x]
• If you’re not using the remote control and front panel con-
trols on the monitor, use this mode. When main power is
on/off, remote control lock is released.
09. Color (Command2:i)
GTo adjust the screen color.
14. PIP / Twin (Command2:n)
You can also adjust color in the Video menu.
G To control the PIP (Picture-in-Picture) or Twin Picture.
You can also control the PIP/Twin picture mode using the PIP
or TWIN PICTURE button on the remote control or in the
Twin menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
Transmission
• Refer to ‘Real data mapping 1’. See page 27.
Acknowledgement
[k][n][ ][Set ID][ ][Data][Cr]
Data 0: PIP/DW off
1: PIP
2: DW1
3: DW2
[i][ ][Set ID][ ][OK][Data][x]
Acknowledgement
[n][ ][Set ID][ ][OK][Data][x]
10. Tint (Command2:j)
GTo adjust the screen tint.
You can also adjust tint in the Video menu.
15. PIP Aspect Ratio (Command2:o)
G To select the PIP picture format.
You can also select the PIP picture format using PIP ARC
on the remote control.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64
Transmission
• Refer to ‘Real data mapping 1’. See page 27.
[k][o][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0: 4:3
1: 16:9
[j][ ][Set ID][ ][OK][Data][x]
Acknowledgement
[o][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command2:k)
16. Split Zoom (Command2:p)
GTo adjust the screen sharpness.
GTo operate split zoom function and select the split
You can also adjust sharpness in the Video menu.
zoom section number.
Transmission
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
[k][p][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
Data Min: 21 ~ Max: 99
• Refer to ‘Real data mapping 1’. See page 27.
Acknowledgement
• Refer to ‘Real data mapping 2’.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
[p][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command2:l)
GTo select OSD (On Screen Display) on/off.
Transmission
Real data mapping 2
*
21: Selection 1 of 2 split zoom
24: Selection 4 of 2 split zoom
41: Selection 1 of 4 split zoom
42: Selection 2 of 4 split zoom
44: Selection 4 of 4 split zoom
45: Selection 5 of 4 split zoom
91: Selection 1 of 9 split zoom
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off
1: OSD on
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
99: Selection 9 of 9 split zoom
28 Plasma Monitor
External Control Device Setup
17. PIP Position (Command2:q)
21. Color Temperature (Command2:u)
GTo adjust color temperature.
G To select sub picture position for PIP.
You can also adjust ACC in the Video menu.
You can also adjust the sub picture position using
Win.position on the remote control or in the Twin menu.
Transmission
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Normal 1: Cool 2: Warm 3: User
[k][q][ ][Set ID][ ][Data][Cr]
Data 0: Right down on screen
1: Left down on screen
2: Left up on screen
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
3: Right up on screen
Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
22. Red Adjustment (Command2:v)
GTo adjust red in color temperature.
Transmission
18. Treble (Command2:r)
[k][v][ ][Set ID][ ][Data][Cr]
GTo adjust treble.
Data Min: 0 ~ Max: C8
You can also adjust treble in the Audio menu.
• Refer to ‘Real data mapping 3’ as shown below.
Acknowledgement
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
[v][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 1’. See page 27.
Acknowledgement
23. Green Adjustment (Command2:w)
[r][ ][Set ID][ ][OK][Data][x]
GTo adjust green in color temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
19. Bass (Command2:s)
Data Min: 0 ~ Max: C8
GTo adjust bass.
• Refer to ‘Real data mapping 3’ as shown below.
You can also adjust bass in the Audio menu.
Acknowledgement
Transmission
[w][ ][Set ID][ ][OK][Data][x]
[k][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 1’. See page 27.
Acknowledgement
24. Blue Adjustment (Command2:$)
GTo adjust blue in color temperature.
Transmission
[s][ ][Set ID][ ][OK][Data][x]
[k][$][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: C8
20. Balance (Command2:t)
• Refer to ‘Real data mapping 3’ as shown below.
Acknowledgement
GTo adjust balance.
You can also adjust balance in the Audio menu.
[$][ ][Set ID][ ][OK][Data][x]
Transmission
Real data mapping 3
*
[k][t][ ][Set ID][ ][Data][Cr]
0 : -20
5 : -19
A : -18
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 1’. See page 27.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
5F: -1
64: 0
69: +1
C3: +19
C8: +20
Owner’s Manual 29
External Control Device Setup
25. PIP Input Select (Command2:y)
29. Orbiter Time Setting (Command2:r)
GTo adjust orbiter operation time term.
G To select input source for sub picture in PIP mode.
Transmission
Transmission
[j][r][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: FE
[k][y][ ][Set ID][ ][Data][Cr]
Data 0: RGB
2: Video
1: Component
3: S-video
4: DVI
Acknowledgement
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
[y][ ][Set ID][ ][OK][Data][x]
26. Abnormal State (Command2:z)
30. Orbiter Pixel Setting (Command2:s)
GTo recognize an abnormal state.
GTo adjust pixel number in orbiter function.
Transmission
Transmission
[k][z][ ][Set ID][ ][FF][Cr]
Data FF:Read
[j][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 9
Acknowledgement
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
[s][ ][Set ID][ ][OK][Data][x]
Data 0: Normal (Power on and signal exist)
1: No signal (Power on)
2: Turn the monitor off by remote control
3: Turn the monitor off by sleep time function
4: Turn the monitor off by RS-232C function
5: 5V down
31. Picture Size Setting for Twin Picture mode
(Command2:t)
GTo adjust main picture size in twin picture mode.
6: AC down
Transmission
7: Turn the monitor off by Fan Alarm function
8: Turn the monitor off by off time function
9: Turn the monitor off by auto off function
a: Turn the monitor off by AV board detect
[j][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 27.
Acknowledgement
27. ISM Method (Command2:p)
[t][ ][Set ID][ ][OK][Data][x]
GTo avoid having a fixed image remain on screen.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
32. Auto Configure (Command2:u)
Data 0: Normal
1: White wash
2: Orbiter
3: Inversion
GTo adjust picture position and minimize image shaking
automatically. Auto Configure only works in RGB-PC
mode.
Acknowledgement
Transmission
[p][ ][Set ID][ ][OK][Data][x]
[j][u][ ][Set ID][ ][Data][Cr]
Data 1: To set
28. Low Power (Command2:q)
Acknowledgement
GTo control the low power function on/off.
Transmission
[u][ ][Set ID][ ][OK][Data][x]
[j][q][ ][Set ID][ ][Data][Cr]
Data 0: Low power off
1: Low power on
Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
30 Plasma Monitor
IR Code
IR Code
How to Connect
G
Connect your wired remote control to the Remote Control port on the Monitor.
Remote Control IR Code
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
TC
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
G Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
G Lead code
9 ms
4.5 ms
0.55 ms
G Repeat code
9 ms
2.25 ms
G Bit description
• Bit “0”
• Bit “1”
0.56 ms
1.12 ms
0.56 ms
2.24 ms
G Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
Owner’s Manual 31
IR Code
Code (Hexa)
Function
Note
UP (D)
DOWN (E)
VOL+ (G)
00H
01H
02H
03H
08H
C4H
C5H
09H
10H
11H
12H
13H
14H
15H
16H
17H
18H
19H
0BH
D5H
C6H
5AH
D8H
BFH
0EH
44H
43H
52H
4DH
60H
61H
63H
64H
6BH
40H
41H
69H
6AH
7BH
79H
76H
77H
AFH
99H
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On/Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (RGB/DVI/Video/S-video/Component)
Discrete IR Code (Input RGB Selection)
Discrete IR Code (Input DVI Selection)
Discrete IR Code (Input Video Selection)
Discrete IR Code (Input S-video Selection)
Discrete IR Code (Input Component Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (PIP/TWIN Exchange)
R/C Button (4:3/16:9)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
VOL- (F)
POWER On/Off
POWER ON
POWER OFF
MUTE
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
AII INPUT SELECT
RGB
DVI
VIDEO
S-VIDEO
COMPONENT
SLEEP
OK (Á)
MENU
DASP
APC
PIP
SUB INPUT
SWAP
PIP ARC
TWIN PICTURE
ZOOM +
ZOOM -
Window Size
Window Position
Split Zoom
ARC
ARC (4:3)
ARC (16:9)
ARC (ZOOM)
Auto configure
R/C Button
R/C Button(4:3/16:9/Zoom Mode Selection)
Discrete IR Code (Only 4:3 mode)
Discrete IR Code (Only 16:9 mode)
Discrete IR Code (Only ZOOM mode)
Discrete IR Code (Only RGB-PC mode)
32 Plasma Monitor
Troubleshooting Checklist
Troubleshooting Checklist
• Check whether the Monitor is turned on.
• Power cord inserted into wall outlet?
No picture &
No sound
• Test the wall power outlet, plug other product’s power cord into the wall outlet
where the Monitor’s power cord was plugged in.
• Press the VOLUME (G) button.
Picture OK &
No sound
• Sound muted? Press MUTE button.
• Check to see if there is any object between the Plasma Display and the
remote control causing obstruction.
The remote control
• Are batteries installed with correct polarity (+ to +, - to -)?
doesn’t work
(Refer to p.8)
• Install new batteries. (Refer to p.8)
• This is normal, the image is muted during the plasma display startup process.
Please contact your service center, if the picture has not appeared after five
minutes.
Picture appears slowly
after switching on
• Select Color in the VIDEO menu and press the VOLUME (G) button.
(Refer to p.16)
No or Poor color
or Poor picture
• Keep a sufficient distance between the Monitor and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.)
Horizontal/vertical bars
or picture shaking
• Check for local interference such as an electrical appliance or power tool.
No output from one of
the speakers
• Adjust Balance in the AUDIO menu. (Refer to p.17)
• A change in ambient humidity or temperature may result in an unusual noise
when the plasma display is turned on or off and does not indicate a fault with
the monitor.
Unusual sound from
inside the monitor
Owner’s Manual 33
Maintenance
Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your
new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and
a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the
screen.
2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor.
Cleaning the Cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.
Extended Absence
If you expect to leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to
unplug the power cord to protect against possible damage from lightning or power surges.
34 Plasma Monitor
Specification
Product Specifications
MU-50PZ44/44A/44B/44K/44R/44S
MU-50PZ44M/44MA/44MB/44MK/44MR/44MS
MU-50PZ44V/44VA/44VB/44VK/44VR/44VS
MU-50PZ90/90A/90B/90K/90R/90S
MU-50PZ90M/90MA/90MB/90MK/90MR/90MS
MU-50PZ90V/90VA/90VB/90VK/90VR/90VS
MODELS
Width (inches / mm)
Height (inches / mm)
Depth (inches / mm)
Weight (pounds / kg)
Power requirement
Resolution
48.2 / 1223
28.9 / 734
4.1 / 105
95.2 / 43.2
AC120V, 60Hz
1366 x 768 (Dot)
Color
16,770,000 (256 steps of each R, G and B)
32 ~ 104°F (0 ~ 40°C)
Less than 80%
Operating Temperature Range
Operating Humidity Range
Maximum Elevation
6561 feet (2000m)
•
The specifications shown above may be changed without notice for quality improvement.
Owner’s Manual 35
|