User’s Guide
L194WT
L204WT
L194WTM
L204WTM
L194WTQ
L204WTQ
L194WTX
L204WTX
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
A2
Connecting the speakers
-
The feature is only for speaker models - L194WTM, L204WTM
Connecting the speaker
1. Place the monitor with its front facing downward on a soft cloth.
2. Insert the protruding hook of the speaker in the direction of the slot in the back of the product.
Slot
Hook
Audio DC-In
Cable
3. After setting up the speaker, connect the Audio DC-In Cable to the back of the product.
20.1 inch monitor
19 inch monitor
A
C
-
I
N
D
C
-O
U
T
D
-S
U
B
D
V
I-D
D
C
-O
U
T
D
-S
U
B
D
V
I-D
A
C
-IN
A3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand
1
.
2.
Place the monitor with its front facing downward on a soft cloth.
Assemble the Stand Body into the product in the correct direction as shown in the picture.
Make sure you push it until you hear it “click”.
R E A R
3
.
4.
Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.
Once assembled take the monitor up carefully and face the front side
REAR
FR
ONT
REAR
R E A R
FR
ONT
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
A4
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚
20
Warning:
When adjusting the angle of the screen, do not
put your finge r(s ) in be tw e e n the he ad of the
m onitor and the s tand body. You can hurt your
finger(s).
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
A5
Connecting the Display
Using the Computer
1. Place the monitor in a convenient, well-ventilated location near your computer.
2. Connect the signal cable. When attached, tighten the thumbscrews to secure the
1
connection.
3. Connect the power cord into a proper power outlet that is easily accessible and close to
2
the display.
19 inch monitor
Signal Cable
PowerCord
Analog signal Digital signal
NOTE
D-sub
DVI
This is a simplified representation
of the rear view.
This rear view represents a
general model; your display may
differ from the view as shown.
Varies according to model.
Wall-outlet type
2
1
PC-outlet type
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed
to change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
PC
DVI-D(This feature is not available in all countries.)
A6
Connecting the Display
20.1 inch monitor
Signal Cable
Analog signal Digital signal
PowerCord
D-sub
DVI
Varies according to model.
Wall-outlet type
NOTE
2
This is a simplified representation
of the rear view.
This rear view represents a
general model; your display may
differ from the view as shown.
1
PC-outlet type
DVI-D(This feature is not available in all countries.)
PC
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to change
the 15 pin high density (3 row) D-sub VGA connector on the supplied
cable to a 15 pin 2 row connector.
4. Press
button on the front switch panel to turn the power on.
When monitor power is turned on, the 'Self Image Setting
Function' is executed automatically.
(Only Analog Mode)
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual
input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push the
‘AUTO/SET’ button on the front panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on the
OSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.
A7
Using the speakers - The feature is only for speaker models - L194WTM, L204WTM
Side Jack
Headphone/Earphone Input
Automatically mutes the speaker volume
when the headphones are plugged in.
Rear
Audio Input
Connects to the *LINE OUT jack of the
PC sound card.
*LINE OUT
A terminal used to connect to the
AUDIO
IN
speaker including a built-in amplifier
(Amp). Make sure that the connecting
terminal of the PC sound card is checked
before connecting. If the Audio Out of PC
sound card has only Speaker Out,
reduce the PC volume.
If the Audio Out of the PC sound card
supports both Speaker Out and Line Out,
convert to Line Out using the card
jumper of the program (Refer to the
Sound Card Manual).
Speaker Out
*Line Out
<Jack of the PC sound card>
A8
Control Panel Functions
Back
Front Panel Controls
Control
Function
Use this button to enter or exit the On Screen Display.
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
Use these buttons to select or adjust functions in the On
Screen Display.
Buttons
:
For more information, refer to page A16.
SOURCE Hot key
Use this button to make D-Sub or DVI connector active.
This feature is used when two computers are connected
to the display. The default setting is D-Sub.
A9
Control Panel Functions
Control
Function
Use this button to enter a selection in the On Screen
Display.
AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SET button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
19 inch monitor : 1440 x 900
20.1 inch monitor : 1680 x 1050
Power Button
Use this button to turn the display on or off.
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
Power Indicator
A10
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the
or Buttons. When the icon you want
becomes highlighted, press the AUTO/SET Button.
Use the
/
Buttons to adjust the image to the desired level. Use the
AUTO/SET Button to select other sub-menu items.
Push the MENU Button once to return to the main menu to select another
function. Push the MENU Button twice to exit from the OSD.
A11
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
Main menu
Sub-menu
BRIGHTNESS
CONTRAST
GAMMA
A
D
Reference
PICTURE
To adjust the brightness,
contrast and gamma of the
screen
sRGB
To customize the color of
the screen
COLOR
PRESET
6500K
9300K
RED
GREEN
BLUE
To adjust the position of the
screen
HORIZONTAL
POSITION
VERTICAL
CLOCK
To improve the clarity and
stability of the screen
PHASE
TRACKING
SHAPNESS
LANGUAGE
SETUP
To customize the screen
status for a user's operating
environment
OSD
HORIZONTAL
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
FACTORY RESET
MOVIE / TEXT
FLATRON
F-ENGINE
To select or customize
desired image settings
USER
NORMAL
: Adjustable
A : Analog Input
D : Digital Input
NOTE
The order of icons may differ depending on the model (A12~A16 ).
A12
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
P I C T U R E
Menu Name
Sub-menus
Icons
Button Tip
MENU
SET
: Exit
: Adjust (Decrease/Increase)
: Enter
: Select another sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
A13
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
P I C T U R E
To adjust the brightness of the screen.
To adjust the contrast of the screen.
BRIGHTNESS
CONTRAST
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
COLOR
C O L O R
• sRGB: Set the screen color to fit the
SRGB standard color
PRESET
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
RED
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
GREEN
BLUE
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
POSITION
P O S I T I O N
To move image left and right.
To move image up and down.
HORIZONTAL
VERTICAL
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
A14
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
CLOCK
PHASE
Description
TRACKING
T R A C K I N G
To minimize any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
MENU : Exit
: Decrease
: Increase
SHARPNESS To adjust the clearness of the screen.
SET : Select another sub-menu
SETUP
To choose the language in which the
control names are displayed.
LANGUAGE
S E T U P
OSD
POSITION
To adjust position of the OSD window
on the screen.
If the output of the video card is different
the required specifications, the color
level may deteriorate due to video
signal distortion. Using this function, the
signal level is adjusted to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors are present in the screen.
WHITE
BALANCE
S E T U P
Use this function to set the power
indicator on the front side of the monitor
to ON or OFF.
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned on.
POWER
INDICATOR
MENU : Exit
: Adjust
: Adjust
SET : Select another sub-menu
FACTORY
RESET
Restore all factory default settings except
"LANGUAGE."
Press the
button to reset immediately.
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal.
A15
On Screen Display(OSD) Selection and Adjustment
The OSD screen will appear when you touch the
button
on the right side of the monitor.
Menu Name
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when applied Screen when not applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
appear on the left side, whereas the non-applied
screen will appear on the right side.Touch the SET
button to use the adjusted screen.
Main menu
Sub menu
Description
MOVIE This feature lets you easily select the best desired
TEXT image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE: For animation images in videos or movies
TEXT: For text images (Word processing etc.)
USER User
You can manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different envir
To adjust the USER sub-menu function,
Press the SET Button
...
(Brightness): Adjusts screen brightness.
...
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
...
RCM(Real Color Management): Selects the color mode.
0
Not applied
1
Green enhance
2
Flesh tone
3
Color Enhance
SAVE
Select the
sub-menu using the SET button
and save the YES value using the buttons.
NORMAL This is under normal operating conditions.
A16
Troubleshooting
Check the following before calling for service.
No image appears
G Is the power cord of the
•
•
•
Check and see if the power cord is connected
properly to the power outlet.
display connected?
G Is the power indicator
Press the Power button.
light on?
Adjust the brightness and the contrast.
G Is the power on and the
power indicator blue or
green?
G Is the power indicator
•
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
amber?
• Try to turn on the PC
.
•
•
This message appears when the signal from the
G Do you see an "OUT OF
RANGE" message on
the screen?
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
G Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
Do you see a "OSD LOCKED" message on the screen?
G
Do you see “OSD
LOCKED” when you
push MENU button?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENU button for several
seconds: the message
“OSD UNLOCKED” will appear.
A17
Troubleshooting
Display image is incorrect
G Display Position is
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
incorrect.
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
G On the screen
background, vertical
bars or stripes are
visible.
•
•
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
G Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
Important
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer
.
A18
Troubleshooting
Display image is incorrect
G The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
mono or abnormal.
•
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be higher than AC100-240V 50/60Hz.
G The screen blinks.
Have you installed the display driver?
G
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
G
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
A19
Specifications
L194WT/L194WTQ/L194WTX
Display
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
19 inches viewable
0.2835 mm pixel pitch
Horizontal Freq.
Analog : 30 - 83 kHz (Automatic)
Digital : 30 - 83 kHz (Automatic)
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Sync Input
Vertical Freq.
Input Form
Signal Input
15 pin D-Sub Connector
Video Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1440 x 900 @75 Hz
Digital : VESA 1440 x 900 @60 Hz
VESA 1440 x 900 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B
:
≤
≤
34 W(Typ.)
1 W
1 W
Power
Consumption
0n Mode
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
&Weight
Width 43.48 cm / 17.11 inches 43.48 cm / 17.11 inches
Height 36.99 cm / 14.56 inches 28.73 cm / 11.31 inches
Depth 22.60 cm / 8.89 inches
5.87 cm / 2.31 inches
Net
Tilt
3.6 kg (7.94 lbs)
-5˚~20˚
Tilt Range
AC 100-240V~ 50/60Hz 0.8A
Power Input
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Stand Base
Signal cable
Power cord
NOTE
Information in this document is subject to change without notice.
A20
Specifications
L194WTM
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
19 inches viewable
0.2835 mm pixel pitch
Display
Sync Input
Video Input
Horizontal Freq.
Analog : 30 - 83 kHz (Automatic)
Digital : 30 - 83 kHz (Automatic)
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green),Digital
15 pin D-Sub Connector
Vertical Freq.
Input Form
Signal Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1440 x 900 @75 Hz
Digital : VESA 1440 x 900 @60 Hz
VESA 1440 x 900 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B
:
≤
≤
34 W(Typ.)
1 W
1 W
Power
Consumption
(without speaker)
0n Mode
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
&Weight
Width 43.48 cm / 17.11 inches 43.48 cm / 17.11 inches
Height 36.99 cm / 14.56 inches 28.73 cm / 11.31 inches
Depth 22.60 cm / 8.89 inches
5.87 cm / 2.31 inches
Net
Tilt
3.6 kg (7.94 lbs)
-5˚~20˚
Tilt Range
AC 100-240V~ 50/60Hz 0.8A
Power Input
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Stand Base
Signal cable
Power cord
Audio
RMS Audio Output
1W+1W(R+L)
Input Sensitivity
Speaker Impedance
0.7Vrms
16Ω
NOTE
Information in this document is subject to change without notice.
A21
Specifications
L204WT/L204WTQ/L204WTX
Display
20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
20.1 inches viewable
0.258 mm pixel pitch
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)
Digital : 30 - 83 kHz (Automatic)
Sync Input
Vertical Freq.
Input Form
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Signal Input
15 pin D-Sub Connector
Video Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1680 x 1050 @ 60 Hz
Digital : VESA 1680 x 1050 @ 60 Hz
VESA 1680 x 1050 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B
:
≤
≤
45W(Typ.)
1 W
1 W
Power
Consumption
0n Mode
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
&Weight
Width 46.62 cm / 18.35 inches 46.62 cm / 18.35 inches
Height 38.40 cm / 15.11 inches 30.54 cm / 12.02 inches
Depth 22.60 cm / 8.89 inches
6.46 cm / 2.54 inches
Net
Tilt
4.8 kg (10.58 lbs)
Tilt Range
-5˚~20˚
AC 100-240V~ 50/60Hz 1.2A
Power Input
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Stand Base
Signal cable
Power cord
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A22
Specifications
L204WTM
20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD
Display
Anti-Glare coating
20.1 inches viewable
0.258 mm pixel pitch
Sync Input
Video Input
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)
Digital : 30 - 83 kHz (Automatic)
Vertical Freq.
Input Form
56 - 75 Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green) Digital
15 pin D-Sub Connector
Signal Input
DVI - D connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Analog : VESA 1680 x 1050 @60 Hz
Digital : VESA 1680 x 1050 @60 Hz
VESA 1680 x 1050 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B
:
≤
≤
45W(Typ.)
1 W
1 W
Power
Consumption
(without speaker)
0n Mode
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
&Weight
Width 46.62 cm / 18.35 inches 46.62 cm / 18.35 inches
Height 38.40 cm / 15.11 inches 30.54 cm / 12.02 inches
Depth 22.60 cm / 8.89 inches
6.46 cm / 2.54 inches
Net
Tilt
4.8 kg (10.58 lbs)
Tilt Range
-5˚~20˚
Power Input
AC 100-240V~ 50/60Hz 1.2A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
Stand Base
Signal cable
Power cord
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Audio
RMS Audio Output
1W+1W(R+L)
Input Sensitivity
Speaker Impedance
0.7Vrms
16Ω
NOTE
Information in this document is subject to change without notice.
A23
Specifications
Preset Modes (Resolution)
19 inch monitor
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
70
70
60
75
60
75
75
60
75
75
65
60
75
60
60
75
1
2
3
4
5
6
7
8
9
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
1440 x 900
1440 x 900
1440 x 900
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
55.500
55.935
70.635
10
11
12
13
14
*15
**16
*Recommend Mode
**Only Analog Mode
20.1 inch monitor
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1680 x 1050
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
64.674
65.290
70
60
75
60
75
60
75
75
60
75
60
60
10
*11
**12
*
Digital Recommend Mode
** Analog Recommend Mode
A24
Specifications
Indicator
LED Color
MODE
blue
amber
Off
On Mode
Sleep Mode
Off Mode
Signal Connector Pin Assignment
8
16
24
1
9
17
DVI-D Connector
Pin
1
2
3
4
5
6
7
8
Signal(DVI-D)
T. M. D. S. Data2-
T. M. D. S. Data2+
T. M. D. S. Data2/4 Shield
T. M. D. S. Data4-
T. M. D. S. Data4+
DDC Clock
Pin
16
Signal(DVI-D)
Hot Plug Detect
T. M. D. S. Data0-
T. M. D. S. Data0+
T. M. D. S. Data0/5 Shield
T. M. D. S. Data5-
T. M. D. S. Data5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock-
17
18
19
20
21
22
23
24
DDC Data
Analog Vertical Sync.
T. M. D. S. Data1-
T. M. D. S. Data1+
T. M. D. S. Data1/3 Shield
T. M. D. S. Data3-
T. M. D. S. Data3+
+5V Power
9
10
11
12
13
14
15
Ground (return for +5V,
H. Sync. and V. Sync.)
T. M. D. S. (Transition Minimized Differential Signaling)
A25
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. Place the monitor with its front facing downward on a soft cloth.
2. Hold the body of the stand as shown in the image
and bend slightly to the
1
right.
2
3. Pull the stand to the direction as shown in the image
to separate.
1
2
R
A
E
R
T
4. Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or will mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate is
purchased.
Kensington Security Slot
Connected to a locking
cable that can be purchased
separately at most
computer stores
A26
Digitally yours
|