Specifications
Model
AV-21FT
B, G, I, D, K, K1
PAL, SECAM, NTSC 3.58 / 4.43 MHz (in VIDEO mode only)
= 46.25 to 168.25 MHz
VHF high channel (VH) = 175.25 to 463.25 MHz
UHF channel (U) = 471.25 to 863.25 MHz
AV-21AT
COLOUR TELEVISION
TV RF systems
Colour systems
Contents
AV-21FT
AV-21AT
Channel and frequencies VHF low channel (VL)
Locations ................................
Preparation .............................
Viewing a Television
2
4
I Receives cable channels in mid band (X to Z, S1 to S10),
super band (S11 to S20) and hyper band (S21 to S41) .
Power input
AC110 to 240 V, 50 / 60 Hz
Programme ...........................12
Power consumption
Maximum 105 W, Average 68 W
Screen size
(measured diagonally)
Picture tube 55 cm
Visible area 51 cm
Viewing Images from an
External Device ....................14
INSTRUCTIONS
Thank you for purchasing this JVC
colour television.
To ensure your complete
understanding, please read this
manual thoroughly before operation.
Audio output
(Rated power output)
5W (monaural)
5W (monaural)
Sound and Picture ...............15
Other Features......................17
Speakers
(6 cm × 12 cm) oval × 2
(5 cm × 9 cm) oval × 2
External input / output
VIDEO input (RCA)
AUDIO input (RCA)
Troubleshooting ...................23
Specifications.........Back cover
VIDEO output (RCA)
AUDIO output (RCA)
Headphone jack: mini jack (dia. 3.5 mm)
Dimensions (W × H × D) 619 mm × 458 mm × 486.5 mm 502 mm × 451 mm × 480.5 mm
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR
MOISTURE.
Weight
22 kg
19.5 kg
Accessories
• Remote control unit: RM-C364 × 1
• AA / R6 / UM-3 dry cell battery × 2
Design and specifications subject to change without notice.
CAUTION:
• TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES
REGARDING THE USE OF THIS TV.
• Operate only from the power source specified on the TV.
• Avoid damaging the power plug and power cord.
• Avoid improper installation and never position this TV where good ventilation is
unattainable. When installing this TV
distance recommendations must be
maintained between the floor and
15 cm
wall, as well as installment in a tightly
enclosed area or piece of furniture.
Adhere to the minimum distance
10 cm
10 cm
15 cm
guidelines shown for safe operation.
• Do not allow objects or liquid into the cabinet openings.
• In the event of a fault, unplug this TV and call a service technician. Do not
attempt to repair it by yourself or remove the rear cover.
• When you don’t use this TV for a long period of time, be sure to disconnect the
power plug from the AC outlet.
LCT0748-001A-H
0400-Ki-AB-NV-JMT
2000 VICTOR COMPANY OF JAPAN, LIMITED
Preparation
Preparation
I Connecting other external devices
1. Connecting the aerial and external devices
Notes: .........................................................................................................................
• For further details, refer to the manuals provided with the devices you are connecting.
• Connecting cables are not supplied.
• The front and rear AUDIO/VIDEO input jacks are directly connected so that input to either
jack is output through both.You cannot provide input to both the front and rear jacks at the
same time. Disconnect one input, or use one of the jacks as an output jack only (for
monitoring or recording).
....................................................................................................................................
To audio
output
To video
output
I Connecting the aerial and VCR
If not connecting a VCR (video cassette recorder), do 1.
If connecting aVCR, proceed 1 © 2 © 3.
• You can view images from the VCR without doing 3. For details, see “To view
images from a VCR connected to the TV with only an aerial cable” on page 14.
VIDEO AUDIO
IN
VCR (for playing)
OUT
VCR (for recording)
VHF/UHF outdoor aerial
To audio
input
To video
input
To video
output
Camcorder
1
VIDEO AUDIO
IN
or
TV game
To audio
output
OUT
2
3
To RF
output
To audio
output
To video
output
MENU
VIDEO AUDIO
IN
Headphones
To aerial input
VCR
1
• Illustration of AV-21FT.
Note: ..................................................................................................................
• Use headphones with a mini jack (dia. 3.5 mm). When using headphones, the speaker
sound output is disabled.
...........................................................................................................................
• Illustration of AV-21FT.
5
4
Preparation
Preparation
5. Selecting the on-screen language
2. Connecting the power cord
You can select one of three languages for the on-screen display. The displayed
menus on the screen are described in the selected language.
Insert the Power plug into an AC outlet.
In this manual, on-screen descriptions are given in English. Select ENGLISH.
3. Inserting batteries into the remote control
Correctly insert two batteries, observing the
end first.
and
polarities and inserting the
CHANNEL
SCAN
RETURN+
- --
/
0
DISPLAY
MUTING
CAUTION: ...........................................
DISPLAY button
• Follow the cautions printed on the
batteries.
............................................................
MENU
MENU
/
buttons
MENU –/+ buttons
Notes: .................................................
CHANNEL
VOLUME
• Use AA/R6/UM-3 dry cell batteries.
• Battery life is approximately six months to
one year depending on frequency of use.
• If the remote control operates erratically,
replace the batteries.
• For details on menu operations using the front control buttons on the TV, see
page 22.
• We recommend that you use the supplied
batteries initially and replace them as
soon as operation becomes erratic.
The supplied batteries are for testing, not
regular use.
1. Press MENU
to display the following menu.
The following menu is displayed in one of three languages.
/
............................................................
ꢀꢁꢂꢃ
3
MENU
3
AUTO CH PRESET
MANUAL CH PRESET
Aꢄꢅꢆ ꢂꢇꢈꢅꢉꢆꢊꢋꢇ
ꢉꢌꢍꢂꢇꢎ ꢂꢇꢈꢅꢉꢆꢊꢋꢇ
LANGUAGE
ENGLISH
ꢎꢏꢐꢋ
ꢉꢌꢈꢈꢋꢑꢊ
4.Turning your TV on
ꢄꢐꢒꢉꢇꢅꢓ
ꢌꢖꢉꢇꢄꢗ -+
ꢄꢐꢔꢆꢕ
DISPLAY
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
1. Press the Main power button on the TV to turn the TV’s main power
on.
English
Chinese
Russian
Notes: ...................................................................................................................
• If a different menu is displayed, repeatedly press the MENU
is displayed.
• If the menu appears in English, the TV’s on-screen language is already set to English, so
you can skip steps 2 and 3.
..............................................................................................................................
The POWER lamp lights.
button until this menu
/
If image does not appear:
Your TV is in the standby mode. Press the POWER button on the remote control
to turn your TV on.
• You can also turn on your TV by pressing the CHANNEL
/
button on your
TV.
2. Press MENU
menu.
to select the third item on the
/
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
To turn your TV off:
Press the POWER button on the remote control.Your TV enters the standby
mode.
LANGUAGE
ENGLISH
3. Press MENU –/+ to select ENGLISH.
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
To turn the TV’s main power off:
Press the Main power button on the TV. The POWER lamp goes off.
The menu is displayed in English.
4. Proceed to “6. Presetting TV stations” on the following page.
• If you want to complete operations at this stage, press the DISPLAY button to
turn the menu display off.
7
6
Preparation
Preparation
I Manual Channel Preset
You can manually preset the desired TV stations to the desired channels.
6. Presetting TV stations
To view a TV programme, you must first preset TV stations to channels on the TV.
This TV has 100 channels (channel 1 to 99 and channel AV).
You can choose between two functions, the Auto Channel Preset and Manual
Channel Preset and preset TV stations to channels on TV.
1. Press MENU
PRESET.
to select MANUAL CH
/
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
LANGUAGE
ENGLISH
• If a different menu is displayed, repeatedly press the
MENU button until this menu is displayed.
Note: ...........................................................................................................................
/
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
• After you have finished presetting, you can set undesired channels to be skipped over, see
page 11.
....................................................................................................................................
2. Press MENU –/+.
MANUAL
FINE
SKIP
The sub-menu is displayed.
NO
B/G
SOUND SYSTEM
EXIT
• The channel No. is displayed as a PR No. For
example, channel 1 will be displayed as PR 1.
However, channel AV will be displayed as AV.
DISPLAY
MUTING
Channel
No.
SELECT BY
PROGRAM BY -+
SEARCH BY VOL-+ DISPLAY
PR 1 VL
EXIT BY
DISPLAY button
MENU
MENU
/
buttons
MENU –/+ buttons
3. Press MENU –/+ to select the channel No. to be preset.
CHANNEL
VOLUME
VOLUME –/+ buttons
REMOTE CONTROL UNIT
RM-C364
4. Press VOLUME –/+ to start selection of the TV station.
or
is displayed on the screen.
When a TV station is received, the
or
display goes out, and the TV
station is preset to the currently selected channel No.
I Auto Channel Preset
You can automatically preset all TV stations that can be received on your TV to
channels in one simple operation.
• If you have selected the wrong TV station for preset, repeatedly press the
VOLUME –/+ button until the desired TV station is selected.
• To stop the Manual Channel Preset, press any button other than the VOLUME
–/+ button.
Notes: .........................................................................................................................
• When you use this function, no station is preset to the channel AV.
Channel AV is offered for viewing images from a VCR connected to your TV with only an
aerial cable. For more details, see page 14.
• If the Auto Channel Preset does not work well, preset TV stations manually, see page 9.
....................................................................................................................................
If the picture is not clear:
Use the Fine function to fine-tune the TV station.
1. Press MENU
to select FINE.
/
MANUAL
FINE
SKIP
SOUND SYSTEM
EXIT
NO
B/G
2. Hold VOLUME –/+ down to fine-tune the TV
station so that the best image is displayed on
screen.
1. Press MENU
to select AUTO CH PRESET.
• If a different menu is displayed, repeatedly press the
MENU button until this menu is displayed.
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
/
LANGUAGE
ENGLISH
SELECT BY
PROGRAM BY -+
FINE
PR 3 VL
EXIT BY
BY VOL-+ DISPLAY
/
or indicates that the TV station is being
fine-tuned.
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
2. Press MENU – /+ to start the Auto Channel
Preset function.
ON SEARCH is displayed on the screen.
When you have finished presetting all TV channels that can be received on your
TV, the display will go out and the Auto Channel Preset function will end.
• To stop the Auto Channel Preset, press the MENU –/+ button.
Continued on next page.
9
8
Preparation
Preparation
I Skip
MANUAL
FINE
SKIP
SOUND SYSTEM
EXIT
5. Press MENU
to select SOUND SYSTEM.
/
When selecting channels, you can set undesired channels to be skipped.
NO
B/G
Channels set to be skipped cannot be selected by the CHANNEL
the CHANNEL SCAN button.
• Channels to which a station has not been preset are automatically set to be
/
buttons nor
6. Press VOLUME –/+ to select the appropriate
sound system.
SELECT BY
PROGRAM BY -+
CHANGE BY VOL-+ DISPLAY
PR 3 VL
EXIT BY
• For the sound systems in each country or region, refer
to the table “The Broadcasting systems of Each
country or Region”.
skipped.
1. Press MENU
PRESET.
to select MANUAL CH
/
MENU
AUTO CH PRESET
MANUAL CH PRESET
3
LANGUAGE
ENGLISH
7. Press MENU
to select MANUAL.
/
• If a different menu is displayed, repeatedly press the
MENU button until this menu is displayed.
/
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
8. Repeat steps 3 to 7 if you want to preset another TV station to a
channel.
2. Press MENU –/+.
MANUAL
FINE
SKIP
SOUND SYSTEM
EXIT
The sub-menu is displayed.
NO
B/G
9. Press DISPLAY to turn the display off.
SELECT BY
PROGRAM BY -+
PR 1 VL
EXIT BY
SEARCH BY VOL-+ DISPLAY
3. Press MENU
to select SKIP.
/
MANUAL
FINE
SKIP
SOUND SYSTEM
EXIT
NO
B/G
• The channel No. is displayed as a PR No. For
example, channel 1 will be displayed as PR 1.
However, channel AV will be displayed as AV.
Channel
No.
SELECT BY
PROGRAM BY -+
YES/NO BY VOL-+ DISPLAY
PR 1 VL
EXIT BY
The Broadcasting Systems of Each Country or Region
System
Area
Country or Region
4. Press MENU –/+ to select the channel you want to skip.
Sound
Colour
Bahrain, Kuwait, Oman, Qatar,
United Arab Emirates, Yemen, etc.
Indonesia, Malaysia, Singapore,
Thailand, India, etc.
MANUAL
FINE
SKIP
SOUND SYSTEM
EXIT
5. Press VOLUME –/+ to select YES.
PAL
B/G
The channel you selected is set to be skipped.
YES
B/G
Asia,
Middle
East
To cancel the Skip:
select NO.
SELECT BY
PROGRAM BY -+
YES/NO BY VOL-+ DISPLAY
PR 5 VL
EXIT BY
China, Vietnam, etc.
PAL
PAL
D/K
I
Hong Kong, etc.
6. Repeat steps 4 and 5 if you want to set another
channel to skip.
Islamic Republic of Iran, Lebanon,
Saudi Arabia, etc.
SECAM
B/G
Russia, etc.
SECAM
PAL
D/K
D/K
B/G
I
Czech Republic, Poland, etc.
Germany, Holland, Belgium, etc.
UK, etc.
7. Press DISPLAY to turn the display off.
Europe
PAL
PAL
Oceania
Africa
Australia, New Zealand, etc.
Republic of South Africa, etc.
Nigeria, etc.
PAL
B/G
I
PAL
PAL
B/G
B/G
Egypt, Morocco, etc.
SECAM
11
10
Viewing a Television Programme
Viewing a Television Programme
3. Press VOLUME –/+ to adjust
4. To turn your TV off, press
2. Select a channel.
the sound.
VOLUME
POWER.
I Up/ down selection
POWER
1. Press CHANNEL
/
.
ECO
POWER
CHANNEL
SENSOR
SYSTEM
COLOUR SOUND
If the sound is abnormal:
Repeatedly press the SOUND
SYSTEM button to select the
appropriate sound system. For
details, see “Sound System” on
page 15.
PICTURE
MODE
Note: .............................................
Note: .............................................
• We recommend that you press the
Main power button on the TV to turn
the main power off if you do not plan
to use your TV for a long time or if you
wish to save energy.
1
2
3
6
9
TV/VIDEO
• Up/down selection cannot be selected
for channels to which the Skip has
been set to YES. (See page 11.)
4
5
8
0
......................................................
OFF
7
TIMER
......................................................
SYSTEM
COLOUR SOUND
CHANNEL
SCAN
RETURN+
- --
/
I Direct selection
1. Repeatedly press the -/--
button to select the desired
mode then press the
Number buttons.
DISPLAY
MUTING
MENU
1
4
7
2
5
8
0
3
6
9
CHANNEL
VOLUME
REMOTE CONTROL UNIT
RM-C364
Using the buttons on the TV
- --
/
Condition:...........................................................................................................
• Check to make sure the Child Lock function is set to OFF. When the Child Lock
function is set to ON, the TV cannot be operated using the front control buttons. For
details, see “Child Lock” on page 20.
- : 1-digit mode
(example)
Channel 6 © Press 6.
Channel AV © Press 0.
.............................................................................................................................
1. Press CHANNEL
turn your TV on.
to
3. Press VOLUME –/+ to
/
adjust the sound.
- - : 2-digit mode
(example)
1. Press POWER to turn your
CHANNEL
VOLUME
EXIT
Channel 6 © Press 0, 6.
Channel 16 © Press 1, 6.
Channel AV © Press 0, 0.
TV on.
POWER
Note: ...........................................
• If your TV does not turn on, press
the Main power button and then
press the CHANNEL
again.
....................................................
To turn your TV off:
Press the Main power button to turn
the main power off. The POWER
lamp goes off.
Notes: ...........................................
If the colour is abnormal:
Repeatedly press the COLOUR
SYSTEM button to select the
appropriate colour system. For
details, see “Colour System” on
page 15.
/
button
• If your TV does not turn on, press the
Main power button on the TV then
press the POWER button again.
• You can also turn on your TV by
pressing any of the following buttons;
POWER
2. Press CHANNEL
select a channel.
to
/
/
– the CHANNEL
– the Number buttons
button
SYSTEM
COLOUR SOUND
• If you press the Main power button
again, your TV turns on immediately.
Step 1 is no longer required.
– the TV/VIDEO button
......................................................
CHANNEL
• Illustration of AV-21FT.
13
12
Sound and Picture
Viewing Images from an External Device
You can view images from VCRs or other external devices connected to your TV.
Sound System
If the sound is abnormal, select the
appropriate sound system. Each press
of the SOUND SYSTEM button
To select the VIDEO mode
via MENU operation:
1. Press TV/VIDEO to select the
ECO
POWER
SENSOR
VIDEO mode.
SYSTEM
COLOUR SOUND
PICTURE
MODE
TV/VIDEO
1. Press MENU
to
/
changes the sound system as follows.
1
2
5
3
6
TV/VIDEO
display the MENU 1 and
select INPUT.
TV mode
VIDEO mode
VIDEO
B/G
I
D/K
4
Channel
number
Notes: .................................................
MENU
or AV
• For the sound systems in each country or
region, see the table “The Broadcasting
Systems of Each Country or Region” on
page 10.
• You cannot select any sound system
when in VIDEO mode.
............................................................
Colour System
TV mode:
This mode is for viewing TV
programmes. Press the TV/VIDEO
MENU
1
If the colour is abnormal, select the
appropriate colour system. Each press
of the COLOUR SYSTEM button
INPUT
TV
ON TIMER
PR 1 0:00
OFF
/
VNR
button, or press the CHANNEL
buttons, or press the number
buttons to return to this mode.
changes the colour system as follows.
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
Picture Mode
I
n TV mode (channel 1 to 99 and AV):
2. Press MENU –/+ to select
To view images from a VCR
connected to the TV with only
an aerial cable:
Your VCR must be preset to the
channel AV of this TV.
SECAM
You can select one of three picture
adjustment modes.
Repeatedly press the PICTURE
MODE button to select the desired
mode.
AUTO
PAL
the VIDEO mode.
In VIDEO mode:
MENU
SECAM
AUTO
PAL
Thoroughly read the manual of
your VCR, and preset your VCR to
the channel AV using the Manual
Channel Preset function on page 9.
As a result, you can view images
from your VCR when you select the
channel AV in the TV mode.
NTSC4.43
NTSC3.58
BRIGHT:
Heightens contrast and sharpness.
TV mode changes to VIDEO
mode.
AUTO:
Automatic colour system selection.
STANDARD:
Standardizes picture adjustments.
Notes: .................................................
SOFT:
• For the colour systems in each country or
region, see the table “The Broadcasting
Systems of Each Country or Region” on
page 10.
Softens contrast and sharpness.
If the colour is abnormal:
Repeatedly press the COLOUR
SYSTEM button to select the
appropriate colour system. For
details, see “Colour System” on
page 15.
Note: ...................................................
• If the colour is abnormal even though you
selected AUTO, change the appropriate
colour system manually.
• Pressing the PICTURE MODE button
returns all the picture settings in the
MENU 4 menu to their default settings.
............................................................
............................................................
15
14
Other Features
Sound and Picture
Display
Eco Sensor
Muting
You can continuously display the
current channel number or VIDEO
mode on the screen.
Press the DISPLAY button.
To turn the display off, press the
DISPLAY button again.
You can adjust this TV so that the
screen automatically adjusts to the
optimum contrast according to the
brightness of your room. This function
reduces eye strain and the power
consumption of this TV.
You can turn the volume off instantly.
This is convenient when answering the
phone or when you have visitors.
Press the MUTING button.
To return the sound, press the
MUTING button again.
ECO
POWER
SENSOR
SYSTEM
COLOUR SOUND
PICTURE
MODE
1
2
5
8
0
3
6
9
TV/VIDEO
4
Repeatedly press the ECO SENSOR
button to select the desired mode.
OFF
7
TIMER
Note: ...................................................
• When selecting a channel or VIDEO mode
with no input signal, indication of selected
channel or VIDEO mode becomes fixed
on the screen.
CHANNEL
SCAN
RETURN+
- --
/
Picture Adjustment
ECO SENSOR DISPLAY:
The Eco Sensor function will work.
In this mode, the heart mark
indicating the brightness of your room
is displayed for several seconds each
time the brightness changes. The
number of heart marks displayed on
screen increases as your room
becomes darker.
DISPLAY
MUTING
You can adjust the picture as you like.
............................................................
1. Press MENU
repeatedly
to display the MENU 4.
/
MENU
CHANNEL
VOLUME
MENU
4
Off Timer
TINT
COLOUR
BRIGHT
CONT.
SHARP
You can set this TV to turn off
automatically within a specified period
of time.
Repeatedly press the OFF TIMER
button to select the period of time.
REMOTE CONTROL UNIT
RM-C364
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
ECO SENSOR:
The Eco Sensor function will work.
However, in this mode, the heart mark
will not be displayed even if the
brightness of your room changes.
2. Press MENU
to select an
item and press MENU –/+ to
/
adjust it.
• You can set the period of time a
maximum of 120 minutes in 10
minute increments.
• 1 minute before the Off Timer turns
off the TV, GOOD NIGHT! displays.
–
Item
+
Reddish
TINT (tint)
Greenish
ECO SENSOR OFF:
The Eco Sensor function will not work.
Lighter COLOUR (colour depth) Deeper
Darker
Lower
Softer
BRIGHT (brightness) Brighter
CONT. (contrast) Higher
SHARP (sharpness) Sharper
To display the remaining time:
Press the OFF TIMER button once.
To cancel the Off Timer:
Press the OFF TIMER button to return
the period of time to 0.
Note: .............................................
• TINT (tint) is displayed only when
viewing images from NTSC3.58 or
NTSC4.43 colour systems.
......................................................
Note: ...................................................
• The Off Timer will not turn off the TV’s
main power.
............................................................
3. Press DISPLAY to turn the
display off.
17
16
Other Features
Other Features
5. Press DISPLAY to turn the
display off.
Return +
On Timer
By setting a channel to “Return
channel”, you can return to that
channel with one touch.
Your TV will automatically turn on and
tune into the channel you want after a
certain period of time you have
specified.
ECO
POWER
SENSOR
6. Press POWER to turn the TV
off.
SYSTEM
COLOUR SOUND
PICTURE
MODE
The ON TIMER lamp will stay lit.
1
2
3
6
9
TV/VIDEO
/
1. Press CHANNEL
or the
Notes: ...........................................
Number buttons to select a
channel to set to “Return
channel”.
4
5
8
0
1. Press MENU
repeatedly
/
• If you turn off the TV’s main power by
pressing the Main power button, the
On Timer setting is canceled.
• If you do not turn off the TV after
starting the On Timer, once the time
set for the On Timer is reached, the
channel will automatically switch to
the channel set for the On Timer.
......................................................
to display the MENU 1.
OFF
7
TIMER
2. Press MENU
ON TIMER.
to select
/
CHANNEL
SCAN
RETURN+
- --
/
2. Press RETURN + for more
than 3 seconds continuously.
RETURN PLUS PROGRAMMED!
appears.
DISPLAY
MUTING
MENU
INPUT
ON TIMER
1
TV
Channel
No.
PR 1 0:00
OFF
MENU
VNR
3. When viewing another
channel, press RETURN +.
The channel changes to the
channel set for “Return channel”.
PROGRAM BY -+
SELECT BY
OPERATE BY VOL-+ DISPLAY
EXIT BY
CHANNEL
VOLUME
While the On Timer is operating:
The ON TIMER lamp lights.
3. Press MENU –/+ to select a
channel you want to view
when the TV turns on.
REMOTE CONTROL UNIT
RM-C364
When the time set for the On
Timer is reached:
The TV automatically turns on and the
channel set for the On Timer is
displayed.
To cancel the channel set for
“Return channel”:
Press the RETURN + button for more
than 3 seconds continuously.
• RETURN PLUS CANCELLED!
appears.
Note: .............................................
• You cannot select the channel AV, the
VIDEO modes, and the channels for
which the Skip is set (See page 11).
......................................................
Channel Scan
Notes: .................................................
• For safety reasons the TV will
You can search for the channel you
want to view while scanning all of the
channels that can be viewed on this
TV.
automatically turn off if no operations are
made within approximately two hours after
the TV is turned on with the On Timer.
• The Off Timer and Auto Shutoff have
priority over the On Timer.
Notes: .................................................
• When you turn the TV off, the “Return
channel” setting will be canceled.
• When you press the RETURN + button
while viewing the channel set for “Return
channel”, the channel changes to the
previously viewed channel.
4. Press VOLUME –/+ to select
the period of time after which
you want to turn on the TV.
The ON TIMER lamp lights and the
On Timer starts.
............................................................
1. Press CHANNEL SCAN.
Channels will be scanned in
channel No. order.
• Each time you press the button,
the period of time changes in 15
minute intervals (up to 12 hours).
• When you press the RETURN + button
while in a VIDEO mode, the mode
switches to TV mode. To return to the
channel set for “Return channel”, press
the RETURN + button again.
2. When the channel that you
want to view appears, press
CHANNEL SCAN again
before scanning for the next
channel begins.
MENU
1
INPUT
TV
ON TIMER
VNR
............................................................
PR 3 11:00
OFF
PROGRAM BY -+
SELECT BY
When there is no setting for
“Return channel”:
When you press the RETURN +
button, the channel changes to the
previously viewed channel.
EXIT BY
OPERATE BY VOL-+ DISPLAY
Note: ...................................................
To cancel the On Timer:
Press the VOLUME –/+ button to
return the period of time to 0:00.
• Channel Scan selection cannot be
selected for channels to which the Skip
has been set to YES. (See page 11.)
............................................................
18
19
Other Features
Other Features
Child Lock
Auto Shutoff
Blue Back
4
5
8
0
6
9
OFF
7
TIMER
You can disable the front control
buttons of the TV.
When this function is set to ON, the TV
can be operated using only the remote
control.
Use this function to prevent children
from operating the TV at their own
discretion (without parental consent).
You can set your TV to turn off if no
signals are received for about 15
minutes or longer after the end of a
broadcast.
You can mute the sound and change
the picture into a blue screen while no
signals come into the TV, or when the
input signals are unstable.
CHANNEL
SCAN
RETURN+
- --
/
DISPLAY
MUTING
1. Press MENU
repeatedly
1. Press MENU
repeatedly
/
/
MENU
to display the MENU 2.
to display the MENU 2.
2. Press MENU to select
AUTO SHUTOFF.
2. Press MENU
BLUE BACK.
to select
/
/
CHANNEL
VOLUME
1. Press MENU
repeatedly
/
MENU
AUTO SHUTOFF
CHILD LOCK
BLUE BACK
2
MENU
AUTO SHUTOFF
CHILD LOCK
BLUE BACK
2
REMOTE CONTROL UNIT
RM-C364
to display the MENU 2.
OFF
OFF
OFF
OFF
OFF
ON
2. Press MENU
CHILD LOCK.
to select
/
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
MENU
AUTO SHUTOFF
CHILD LOCK
BLUE BACK
2
OFF
OFF
ON
VNR
3. Press MENU –/+ to select ON.
3. Press MENU –/+ to select ON.
(Video Noise Reduction)
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
AUTO SHUTOFF
ON
BLUE BACK
ON
You can reduce the picture noise.
ON:
ON:
3. Press MENU –/+ to select ON.
1. Press MENU
repeatedly
/
Activates the Auto Shutoff.
OFF:
Activates the Blue Back.
OFF:
to display the MENU 1.
CHILD LOCK
ON
2. Press MENU
VNR.
to select
/
Cancels the Auto Shutoff.
Cancels the Blue Back.
ON:
Notes: ...........................................
Activates the Child Lock, disabling
operation of the TV using the front
control buttons.
4. Press DISPLAY to turn the
display off.
MENU
INPUT
ON TIMER
1
TV
• To view a broadcast even when the
reception signal is poor, set the Blue
Back to OFF.
PR 1 0:00
OFF
VNR
Notes: .................................................
• The Auto Shutoff function does not turn off
the TV’s main power.
• The Auto Shutoff will not work for a
VIDEO mode.
............................................................
OFF:
• Even when the Blue Back is set to
OFF, the sound may not be audible.
• The Blue Back function does not
operate in VIDEO mode.
SELECT BY
OPERATE BY -+
EXIT BY
DISPLAY
Cancels the Child Lock.
4. Press DISPLAY to turn the
display off.
3. Press MENU –/+ to select ON.
......................................................
VNR
ON
Note: ...................................................
4. Press DISPLAY to turn the
display off.
• The Child Lock is canceled when you turn
the TV’s main power off.
............................................................
ON:
Activates the VNR. Select ON
when viewing a noisy picture.
OFF:
Cancels the VNR.
4. Press DISPLAY to turn the
display off.
20
21
Troubleshooting
Other Features
Important: Review all the instructions in this manual.
2. Repeatedly press MENU to
select the desired function or
item.
Problem
Check/Action
Cannot turn TV on
Press the Main power button (see p.6).
Insert the power plug in an AC outlet.
To select a function or item
above the currently selected
function or menu:
Repeatedly press the MENU button
to proceed to another menu, and
then repeatedly press the MENU
button again to return to the
original menu. Then select the
function or item.
No picture nor sound
Press the TV/VIDEO button to select the correct mode (see
p.14).
Check the aerial connections.
Remote control inoperable Replace the batteries (see p.6).
Insert the batteries correctly.
Buttons on front of TV do
not work
Is the Child Lock function ON ? (see p.20).
The TV turns on suddenly The TV will automatically turn on when the On Timer is
operated (see p.19).
MENU –/+ buttons
The TV turns off suddenly The TV will automatically turn off in the following cases.
• When the Off Timer or Auto Shutoff is operated (see p.17
and p.21).
3. Press MENU –/+ or VOLUME
–/+ to carry out the desired
operation.
MENU
CHANNEL
VOLUME
EXIT
• When no operations are made within approximately two hours
after the TV was turned on with the On Timer (see p.19).
Abnormal sound
Abnormal colour
Select the appropriate sound system (see p.15).
• For details, see the description
for the respective function.
Adjust the colour and brightness (see p.16).
Select the appropriate colour system (see p.15).
Set the Picture mode to STANDARD (see p.15).
MENU button
VOLUME –/+
(EXIT) buttons
4. Press VOLUME –/+ to turn the
Lines or streaks in picture
(interference)
Move the components apart until the interference disappears.
Reposition the aerial.
menu display off.
• Illustration of AV-21FT.
Spotted picture (crosstalk) Move the aerial away from the source of interference.
Replace the aerial cable with a coaxial cable, which is less
prone to interference.
If the sub-menu is displayed:
The sub-menu cannot be turned off
by the VOLUME –/+ button when it
is displayed. Follow the procedure
below to turn the sub-menu display
off.
Menu operations using
the buttons on the TV
Double picture (ghost)
Reposition the aerial.
Replace with an aerial with good directionality.
Snowy picture
(image noise)
Check the aerial connection and aim it correctly.
Replace or repair the aerial.
You can operate functions in menus
using the front control buttons on the
TV without having to use the remote
control.
The TV channel changes
suddenly
The channel will automatically be changed when the On Timer
operates (see p.19).
1. Press MENU to select EXIT.
MANUAL
FINE
The screen turns blue
Is the Blue Back set to ON ? (see p.21).
SKIP
NO
Condition: ..........................................
SOUND SYSTEM
EXIT
B/G
The following are normal occurrences and are not the result of TV
malfunctions:
• When a still bright image (of a white dress, for example) appears on the screen, the image
may be coloured. This problem occurs in all CRTs, and when the bright image disappears,
the colouration also disappears.
• This TV is equipped with a microcomputer that may operate abnormally due to interference
from external devices. If this happens, press the Main power button to turn the main power
off and disconnect the power plug from the AC outlet. Then, reconnect the power plug to the
AC outlet and press the Main power button again.
• Check to make sure the Child Lock
function is set to OFF. When the Child
Lock function is set to ON, the TV cannot
be operated using the front control
buttons. For details, see “Child Lock” on
page 20.
SELECT BY
PROGRAM BY -+
EXIT
PR 1 VL
EXIT BY
BY VOL-+ DISPLAY
2. Press VOLUME –/+ to turn the
............................................................
sub-menu display off.
1. Press MENU to display the
menu.
If the desired menu is not
displayed:
Repeatedly press the MENU button
until the desired menu is displayed.
23
22
|