AOC Computer Monitor 2341VG User Manual

2
Safety  
National Conventions  
The following subsections describe notational conventions used in this document.  
Notes, Cautions, and Warnings  
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.  
These blocks are notes, cautions, and warnings, and they are used as follows:  
NOTE: A NOTE indicates important information that helps you make better use of your computer system.  
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to  
avoid the problem.  
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.  
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the  
specific presentation of the warning is mandated by regulatory authority.  
4
 
Power  
The monitor should be operated only from the type of power source indicated on the label. If you are not sure  
of the type of power supplied to your home, consult your dealer or local power company.  
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug  
will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire  
plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat  
the safety purpose of the grounded plug.  
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect  
the monitor from damage due to power surges.  
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.  
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate  
configured receptacles marked between 100 - 240V AC, Min. 5A  
The wall socket shall be installed near the equipment and shall be easily accessible.  
For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license (Only for  
monitors with power adapter).  
5
 
Installation  
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a  
person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by  
the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and  
use mounting accessories recommended by the manufacturer. A product and cart combination should be moved  
with care.  
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or  
electric shock. Never spill liquids on the monitor.  
Do not place the front of the product on the floor.  
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit  
instructions.  
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence  
overheating may cause a fire or damage to the monitor.  
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on  
the stand:  
6
 
Cleaning  
Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead  
of strong-detergent which will cauterize the product cabinet.  
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough  
as it will scratch the screen surface.  
Please disconnect the power cord before cleaning the product.  
Please refer to the drawings below to remove and clean the glass of the monitor.  
The headset can be hanged on the earphone handle as shown on the drawing below.  
7
 
Other  
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and  
contact a Service Center.  
Make sure that the ventilating openings are not blocked by a table or curtain.  
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.  
Do not knock or drop the monitor during operation or transportation.  
8
 
Setup  
Contents in Box  
Not all signal cables (Analog, USB, DVI, and HDMI cables) will be provided for all countries and regions. Please  
check with the local dealer or AOC branch office for confirmation.  
USB Camera will be not provided for customers. Please check with the local dealer or AOC branch office for  
confirmation.  
9
 
Setup Stand & Base  
Please setup or remove the base following the steps as below.  
Setup:  
Remove:  
10  
 
Adjusting Viewing Angle  
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your  
own preference.  
Hold the stand so you will not topple the monitor when you change the monitor's angle.  
You are able to adjust the monitor's angle from -5° to 20 °.  
NOTE:  
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.  
11  
 
Connecting the Monitor  
Cable Connections On Back of Monitor and Computer:  
1. Power  
2. DVI  
3. Analog (DB-15 VGA cable)  
4. USB  
To protect equipment, always turn off the PC and LCD monitor before connecting.  
1
2
Connect the power cable to the AC port on the back of the monitor.  
Connect one end of the 15-pin D-Sub / 24-pin DVI cable to the back of the monitor and connect the other end to the  
computer's D-Sub / DVI port.  
3
Connect one end of the USB cable to the back of the monitor and connect the other end to the computer's USB  
port.  
4
Turn on your monitor and computer.  
If your monitor displays an image, installation is complete. If it does not display an image, please refer  
Troubleshooting.  
12  
 
Wall Mounting  
Preparing to Install An Optional Wall Mounting Arm.  
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this  
procedure. Follow these steps:  
1
2
3
Remove the base and stand.  
Follow the manufacturer's instructions to assemble the wall mounting arm.  
Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the  
back of the monitor.  
4
5
Insert the 4 screws into the holes and tighten.  
Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for  
instructions on attaching it to the wall.  
Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official  
department of AOC.  
13  
 
Adjusting  
Setting Optimal Resolution  
Windows Vista  
For Windows Vista:  
1 Click START.  
2 Click CONTROL PANEL.  
3 Click Appearance and Personalization.  
4 Click Personalization  
14  
 
5 Click Display Settings.  
6 Set the resolution SLIDE-BAR to 1920 by 1080.  
15  
Windows XP  
For Windows XP:  
1 Click START.  
2 Click SETTINGS.  
3 Click CONTROL PANEL.  
4 Click Appearance and Themes.  
5 Double click DISPLAY.  
16  
 
6 Click SETTINGS.  
7 Set the resolution SLIDE-BAR to 1920 by 1080.  
Windows ME/2000  
For Windows ME/2000:  
1 Click START.  
2 Click SETTINGS.  
3 Click CONTROL PANEL.  
4 Double click DISPLAY.  
5 Click SETTINGS.  
6 Set the resolution SLIDE-BAR to  
1920 by 1080.  
17  
 
Hotkeys  
Auto/Exit  
Power  
Eco Mode/<  
4:3 or wide/>  
Menu/Enter  
Power  
Press the Power button to turn 0n/off the monitor.  
Eco Mode / <  
Press the Eco key continuously to select the Eco mode of brightness when there is no OSD ( Eco mode hot key  
may not be available in all models).  
4:3 or wide image ratio / >  
When there is no OSD, press right hotkey continuously to change 4:3 or wide image ratio. (If the product screen size  
is 4:3 or input signal resolution is wide format, the hot key is disable to adjust. )  
Auto /Source / Exit  
When the OSD is closed, press Auto button will be auto configure hot key function .  
When the OSD is closed, press Source (or Auto/Source) button will be Source hot key function (Only for the models  
with dual or more inputs). Press Source button continuously to select the input source showed in the message bar ,  
press Menu/Enter button to change to the source selected.  
18  
 
OSD Setting  
Basic and simple instruction on the control keys.  
1) Press the MENU-button to activate the OSD window.  
2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button  
to activate sub-menu . Once the desired function is highlighted, press MENU-button to activate it.  
3) Press < or > to change the settings of the selected function. Press < or > to select another function in sub-menu .  
Press AUTO to exit . If you want to adjust any other function, repeat steps 2-3.  
4) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press  
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is  
off and then press power button to turn the monitor on.  
Notes:  
1) If the product has only one signal input, the item of "Input Select" is disable to adjust.  
2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disable to  
adjust.  
3) One of DCR, Color Boost, and Picture Boost functions is active, the other two function is turned off accordingly.  
19  
 
Luminance  
Press (Menu) to display menu.  
Press  
or  
to select  
(Luminance), and press  
to enter.  
Press  
or  
to select submenu, press  
or to  
to enter, and press  
adjust.  
Press  
to exit.  
20  
 
Brightness  
Contrast  
0-100  
0-100  
Backlight Adjustment  
Contrast from Digital-register.  
Standard  
Text  
Standard Mode  
Text Mode  
Eco mode  
Internet  
Game  
Movie  
Internet Mode  
Game Mode  
Movie Mode  
Sports Mode  
Sports  
Gamma1  
Gamma2  
Gamma3  
Adjust to Gamma1  
Adjust to Gamma 2  
Adjust to Gamma 3  
Gamma  
DCR  
Disable dynamic contrast ratio  
Enable dynamic contrast ratio  
Off  
On  
21  
Image Setup  
Press  
(Menu) to display menu.  
Press  
or  
to select  
(Image  
Setup), and press  
to enter.  
s  
Press  
or  
to select submenu, press  
to enter, and press  
or  
to  
adjust.  
Press  
to exit.  
22  
 
Adjust picture Clock to reduce  
Vertical-Line noise.  
Clock  
0-100  
0-100  
0-100  
0-100  
Adjust Picture Phase to reduce  
Horizontal-Line noise  
Phase  
Adjust the horizontal position of the  
picture.  
H.Position  
V.Position  
Adjust the vertical position of the  
picture.  
23  
Color Temperature  
Press  
(Menu) to display menu.  
Press  
or  
to select  
(Color  
to enter.  
Temperature), and press  
Press  
or  
to select submenu, press  
or to  
to enter, and press  
adjust.  
Press  
to exit.  
24  
 
Recall Warm Color Temperature  
from EEPROM.  
Warm  
Normal  
Cool  
6500K  
7300K  
9300K  
Recall Normal Color Temperature  
from EEPROM.  
Recall Cool Color Temperature  
from EEPROM.  
Recall SRGB Color Temperature  
from EEPROM.  
sRGB  
Red  
Red Gain from Digital-register  
Green Gain Digital-register.  
Blue Gain from Digital-register  
User  
Green  
Blue  
25  
Color Boost  
Press  
(Menu) to display menu.  
Press  
or  
to select  
to enter.  
(Color  
Boost), and press  
Press  
or  
to select submenu, press  
or to  
to enter, and press  
adjust.  
Press  
to exit.  
26  
 
Full Enhance  
Nature Skin  
Green Field  
Sky-blue  
on or off  
on or off  
on or off  
on or off  
on or off  
on or off  
Disable or Enable Full Enhance Mode  
Disable or Enable Nature Skin Mode  
Disable or Enable Green Field Mode  
Disable or Enable Sky-blue Mode  
Disable or Enable AutoDetect Mode  
Disable or Enable Demo  
AutoDetect  
Demo  
27  
Picture Boost  
Press  
Press  
(Menu) to display MENU.  
or  
to select  
(Picture  
to enter.  
Boost); and press  
Press  
or  
to select Bright Frame.  
Select “on” to activate Picture Boost.  
Press  
or  
to select submenu, press  
or to  
to enter, and press  
adjust.  
Press  
to exit.  
28  
 
Frame Size  
Brightness  
Contrast  
14-100  
0-100  
0-100  
Adjust Frame Size  
Adjust Frame Brightness  
Adjust Frame Contrast  
H. position  
V.position  
0-100  
Adjust Frame horizontal Position  
Adjust Frame vertical Position  
Disable or Enable Bright Frame  
0-100  
Bright Frame  
on or off  
29  
OSD Setup  
Press  
(Menu) to display menu.  
Press  
or  
to select  
(OSD  
Setup), and press  
to enter.  
Press  
or  
to select submenu, press  
or to  
to enter, and press  
adjust.  
Press  
to exit.  
30  
 
OSD Setup  
H.Position  
Adjust the horizontal position of  
OSD  
0-100  
V.Position  
Timeout  
0-100  
5-120  
Adjust the vertical position of OSD  
Adjust the OSD Timeout  
Transparence 0-100  
Language  
Adjust the transparence of OSD  
Select the OSD language  
31  
Extra  
Press  
(Menu) to display menu.  
Press  
or  
to select  
(OSD  
Setup), and press  
to enter.  
Press  
or  
to select submenu, press  
or to  
to enter, and press  
adjust.  
Press  
to exit.  
32  
 
Input Select  
Auto Config  
Select Analog Sigal Source as Input  
Auto adjust the picture to default  
D-SUB  
yes or no  
Image Ratio  
DDC-CI  
wide or 4:3  
yes or no  
0 to 24hrs  
Select wide or 4:3 format for display  
Turn ON/OFF DDC-CI Support  
Select DC off time  
Off time  
Show the information of the main  
image and sub-image source  
Information  
33  
Reset  
Press  
(Menu) to display menu.  
Press  
or  
to select  
to enter.  
(Reset),  
and press  
Press  
or  
to select YES or NO.  
Press  
to exit.  
34  
 
Reset  
yes or no  
Reset the menu to default  
35  
Exit  
Press  
(Menu) to display menu.  
Press  
or  
to select  
to enter.  
(Exit);  
and press  
Exit  
Exit the main OSD  
36  
 
LED Indicator  
Status  
LED Color  
Full Power Mode  
Green or Blue  
Active-off Mode  
Orange or red  
37  
 
Driver  
Monitor Driver  
Windows 7  
1.Start Windows® 7  
2.Click on the 'Start' button and then click on 'Control Panel'.  
3. Click on the 'Display' icon.  
38  
 
4.Ckick on the “Change display settings” button.  
5.Click the Advanced Settings” button.  
6.Click the “Monitor” tab and then click the “Properties” button.  
39  
7.Click the “Driver” tab.  
8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... “and then  
click the "Browse my computer for driver software" button.  
9. Select "Let me pick from a list of device drivers on my computer".  
40  
10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory:  
X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive).  
11. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button.  
12. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk  
drive.  
13. Close all open windows and remove the CD.  
14. Restart the system. The system will automatically select the maximum refresh rate and corresponding Color  
Matching Profiles.  
41  
Windows Vista  
1. Click "Start " and "Control Panel". Then, double-click on "Appearance and Personalization".  
2. Click "Personalization" and then "Display Settings".  
3. Click "Advanced Settings...".  
42  
 
4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your  
monitor is completed. The monitor can be used as is.  
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".  
5. Click "Update Driver..." in the "Driver" tab.  
6. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers  
on my computer".  
7. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive  
F:\Driver (CD-ROM Drive).  
8. Select your monitor model and click on the 'Next' button.  
9. Click "Close" "Close" "OK" "OK" on the following screens displayed in sequence.  
43  
Windows XP  
1. Start Windows® XP  
2. Click on the 'Start' button and then click on 'Control Panel'.  
3. Select and click on the category ‘Appearance and Themes’  
4. Click on the 'Display' Item.  
44  
 
5. Select the 'Settings' tab then click on the 'Advanced' button.  
6. Select 'Monitor' tab  
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.  
- If the 'Properties' button is active, click on 'Properties' button.  
Please follow the steps below.  
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.  
45  
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button.  
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.  
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F:  
(CD-ROM Drive).  
11. Click on the 'Open' button, then click the 'OK' button.  
12. Select your monitor model and click on the 'Next' button.  
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP' message,  
please click on the 'Continue Anyway' button.  
13. Click on the 'Finish' button then the 'Close' button.  
14. Click on the 'OK' button and then the 'OK' button again to close the Display Properties dialog box.  
46  
Windows 2000  
1. Start Windows® 2000  
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.  
3. Double click on the 'Display' Icon.  
4. Select the 'Settings' tab then click on 'Advanced...'.  
5. Select 'Monitor'  
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.  
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.  
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.  
7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on 'Next'  
and then click on 'Have disk...'.  
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).  
9. Click on the 'Open' button, then click on the 'OK' button.  
10. Select your monitor model and click on the 'Next' button.  
11. Click on the 'Finish' button then the 'Close' button.  
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.  
Windows ME  
1. Start Windows® Me  
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.  
3. Double click on the 'Display' Icon.  
4. Select the 'Settings' tab then click on 'Advanced...'.  
5. Select the 'Monitor' button, then click on 'Change...' button.  
6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.  
7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on  
'Next' and then click on 'Have Disk...'.  
8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button.  
9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.  
10. Click on 'Finish' button then the 'Close' button.  
47  
 
i-Menu  
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on  
screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation  
guide.  
48  
 
Troubleshoot  
Problem & Question  
Possible Solutions  
Make sure the power button is ON and the Power Cord is properly connected  
to a grounded power outlet and to the monitor.  
Power LED Is Not ON  
Is the power cord connected properly?  
Check the power cord connection and power supply.  
Is the cable connected correctly?  
(Connected using the D-sub cable)  
Check the DB-15 cable connection.  
(Connected using the DVI cable)  
Check the DVI cable connection.  
* DVI input is not available on every model.  
If the power is on, reboot the computer to see the initial screen (the login  
screen), which can be seen.  
No images on the screen  
If the initial screen (the login screen) appears, boot the computer in the  
applicable mode (the safe mode for Windows ME/XP/2000) and then change  
the frequency of the video card.  
(Refer to the Setting the Optimal Resolution)  
If the initial screen (the login screen) does not appear, contact the Service  
Center or your dealer.  
Can you see "Input Not Supported" on the screen?  
You can see this message when the signal from the video card exceeds the  
maximum resolution and frequency that the monitor can handle properly.  
Adjust the maximum resolution and frequency that the monitor can handle  
properly.  
Make sure the AOC Monitor Drivers are installed.  
Picture Is Fuzzy & Has  
Adjust the Contrast and Brightness Controls.  
Ghosting Shadowing Problem Press to auto adjust.  
Make sure you are not using an extension cable or switch box. We  
recommend plugging the monitor directly to the video card output connector  
on the back .  
Move electrical devices that may cause electrical interference as far away  
from the monitor as possible.  
Picture Bounces, Flickers Or  
Wave Pattern Appears In The  
Picture  
Use the maximum refresh rate your monitor is capable of at the resolution  
your are using.  
49  
 
The Computer Power Switch should be in the ON position.  
The Computer Video Card should be snugly fitted in its slot.  
Make sure the monitor's video cable is properly connected to the computer.  
Inspect the monitor's video cable and make sure no pin is bent.  
Make sure your computer is operational by hitting the CAPS LOCK key on  
the keyboard while observing the CAPS LOCK LED. The LED should either  
turn ON or OFF after hitting the CAPS LOCK key.  
Monitor Is Stuck In Active  
Off-Mode"  
Missing one of the primary  
colors (RED, GREEN, or  
BLUE)  
Inspect the monitor's video cable and make sure that no pin is damaged.  
Make sure the monitor's video cable is properly connected to the computer.  
Screen image is not centered  
or sized properly  
Adjust H-Position and V-Position or press hot-key (AUTO).  
Adjust RGB color or select desired color temperature.  
Picture has color defects  
(white does not look white)  
Horizontal or vertical  
Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and  
disturbances on the screen  
FOCUS.  
Press to auto-adjust.  
50  
Specification  
General Specification  
Model number  
Driving system  
Viewable Image Size  
Pixel pitch  
2341Vg  
TFT Color LCD  
58.5cm diagoanl  
0.2655mm(H) x 0.2655mm(V)  
R, G, B Analog lnterface  
H/V TTL  
Panel  
Video  
Separate Sync.  
Display Color  
Dot Clock  
16.7M Colors  
148.5 MHz  
Horizontal scan range  
30 kHz - 80 kHz  
Horizontal scan Size(Maximum)  
Vertical scan range  
509.76mm  
55 Hz - 75 Hz  
Vertical scan Size(Maximum)  
Optimal preset resolution  
286.74mm  
1920 x 1080 (60 Hz)  
1920 x 1080 (60 Hz)  
VESA DDC2B/CI  
Highest preset resolution  
Resolution  
Plug & Play  
Input Connector  
Input Video Signal  
D-Sub 15pin & DVI 24pin  
Analog: 0.7Vp-p(standard), 75 OHM, Positive  
& DVI-D Digital Interface (TMDS)  
Power Source  
100~240VAC, 50/60Hz  
Active < 30 W  
Power Consumption  
Standby < 0.1 W  
Connector Type  
15-pin Mini D-Sub & 24-pin DVI  
Detachable  
Signal Cable Type  
Dimensions & Weight:  
Physical  
412.5 mm  
619.7 mm  
186.8 mm  
5.55 kg  
Height (with base)  
Characteristics  
Width  
Depth  
Weight (monitor only)  
Environmental Temperature:  
Operating  
C to 40° C  
Non-Operating  
Humidity:  
-25°Cto 55°C  
Operating  
10% to 85% (non-condensing)  
5% to 93% (non-condensing)  
51  
Non-Operating  
 
Altitude:  
Operating  
0~ 3,658m (0~ 12,000 ft )  
Non-Operating  
0~ 12,192m (0~ 40,000 ft )  
Preset Display Modes  
HORIZONTAL  
VERTICAL  
STANDARD  
RESOLUTION  
FREQUENCY(KHz)  
FREQUENCY(Hz)  
640x480@60Hz  
640x480@72Hz  
640x480@75Hz  
800x600@56Hz  
800x600@60Hz  
800x600@72Hz  
800x600@75Hz  
1024x768@60Hz  
1024x768@70Hz  
1024x768@72Hz  
1024x768@75Hz  
1280x1024@60Hz  
1280x1024@70Hz  
1280x1024@72Hz  
1280x1024@75Hz  
1440x900@60Hz  
1680x1050@60Hz  
1152x864@75Hz  
1280x960@60Hz  
1920x1080@60Hz  
720x400@70Hz  
640x480@67Hz  
832x624@75Hz  
31.469kHz  
37.861kHz  
37.5kHz  
59.94 Hz  
72.809 Hz  
75 Hz  
VGA  
35.156kHz  
37.879kHz  
48.077kHz  
46.875kHz  
48.363kHz  
56.476kHz  
57.669kHz  
60.023kHz  
63.981kHz  
74.882kHz  
63.981kHz  
79.976kHz  
55.935kHz  
65.29kHz  
67.5kHz  
56.25 Hz  
60.317 Hz  
72.188Hz  
75 Hz  
SVGA  
XGA  
60.004 Hz  
70.069 Hz  
71.996 Hz  
75.029 Hz  
60.02 Hz  
69.853 Hz  
60.02 Hz  
75.025 Hz  
55.876 Hz  
59.95Hz  
75Hz  
SXGA  
WXGA  
WSXGA  
***  
60kHz  
60Hz  
HD  
67.5kHz  
59.934Hz  
70.087Hz  
66.667Hz  
74.551Hz  
IBM-MODE DOS  
MAC MODE VGA  
MAC MODE SVGA  
31.469kHz  
35kHz  
49.725kHz  
52  
 
Pin Assignments  
Pin Number  
15-Pin Side of the Signal Cable  
Video-Red  
Video-Green  
Video-Blue  
N.C.  
1
2
3
4
5
Detect Cable  
GND-R  
6
7
GND-G  
8
GND-B  
9
+5V  
10  
11  
12  
13  
14  
15  
Ground  
N.C.  
DDC-Serial data  
H-sync  
V-sync  
DDC-Serial clock  
Pin No.  
Signal Name  
Pin No.  
Signal Name  
Pin No.  
Signal Name  
1
2
TMDS Data 2-  
TMDS Data 2+  
9
TMDS Data 1-  
TMDS Data 1+  
17  
18  
TMDS Data 0-  
TMDS Data 0+  
10  
TMDS Data 2/4  
Shield  
TMDS Data 1/3  
Shield  
TMDS Data 0/5  
Shield  
3
11  
19  
4
5
TMDS Data 4-  
TMDS Data 4+  
12  
13  
TMDS Data 3-  
TMDS Data 3+  
20  
21  
TMDS Data 5-  
TMDS Data 5+  
TMDS Clock  
Shield  
6
DDC Clock  
14  
+5V Power  
22  
7
8
DDC Data  
N.C.  
15  
16  
Ground(for+5V)  
Hot Plug Detect  
23  
24  
TMDS Clock +  
TMDS Clock -  
53  
 
Plug and Play  
Plug & Play DDC2B Feature  
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the  
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional  
information about its display capabilities.  
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over  
the DDC2B channel.  
54  
 
Regulation  
FCC Notice  
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
NOTICE :  
The changes or modifications not expressly approved by the party responsible for compliance could void the user's  
authority to operate the equipment.  
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.  
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this  
equipment. It is the responsibilities of the user to correct such interference. It is the responsibility of the user to  
correct such interference.  
55  
 
WEEE Declaration  
Disposal of Waste Equipment by Users in Private Household in the European Union.  
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other  
household waste.Instead, it is your responsibility to dispose of your waste equipment by handing it over to a  
designated collection point for the recycling of waste electrical and electronic equipment.The separate collection  
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure  
that it is recycled in a manner that protects human health and the environment. For more information about where  
you can drop off your waste equipment for recycling, please contact your local city office, your household waste  
disposal service or the shop where you purchased the product .  
HG Declaration  
SAFETY: Lamp Disposal  
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF  
ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE  
ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.  
56  
   
EPEAT Declaration  
EPEAT is a system to help purchasers in the public and private sectors evaluate, compare and select desktop  
computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and  
consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers to  
secure market recognition for efforts to reduce the environmental impact of its products.  
AOC believes in protecting the environment.  
With a key concern for the conservation of natural resources, as well as land ll protection, AOC announces the  
launch of AOC monitor’s packaging recycling program. This program is designed to help you discard of your  
monitor carton and ller materials properly. If a local recycling center is not available, AOC will recycle the  
packaging material for you, including foam ller and carton. AOC Display solution will only recycle AOC monitor  
packaging. Please refer to the following website address:  
Only for North and South American, excluding Brazil:  
For Germany:  
For Brazil:  
57  
 
Service  
Warranty Statement for Europe  
LIMITED THREE-YEAR WARRANTY*  
AOC Color Monitors sold within Europe  
AOC International (Europe) GmbH warrants this product to be free from defects in material and workmanship for a  
period of Three (3) years after the original date of consumer purchase. During this period, AOC International  
(Europe) GmbH will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a  
new or rebuilt product at no charge except as *stated below. The defective products that are replaced become the  
property of AOC International (Europe) GmbH.  
If the product appears to be defective, please contact your local dealer or refer to the warranty card when attached  
to the product.  
Deliver the product freight pre-paid, along with the dated proof of purchase, to the AOC Authorized Service Center.  
If you cannot deliver the product in person:  
Pack it in its original shipping container (or equivalent)  
Put the RMA number on the address label  
Put the RMA number on the shipping carton  
Insure it (or assume the risk of loss/damage during shipment)  
Pay all shipping charges  
AOC International (Europe) GmbH is responsible neither for any damage or loss during inbound transport damage  
nor to inbound product that was not properly packaged.  
AOC International (Europe) GmbH will pay the return shipping charges within one of the countries specified within  
this warranty statement. AOC International (Europe) GmbH is not responsible for any costs associated with the  
transportation of product across international borders. This includes the international border within the European  
Union.  
* This limited warranty does not cover any losses or damages that occur as a result of  
Shipping or improper installation or maintenance  
Misuse  
Neglect  
Any cause other than ordinary commercial or industrial application  
Adjustment by non-authorized source  
Repair, modification, or installation of options or parts by anyone other than an AOC Authorized Service Center  
Improper environment  
Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other irregularities  
This limited warranty does not cover any of the product firmware or hardware that you or any third party have  
58  
 
modified or altered; you bear the sole responsibility and liability for any such modification or alteration.  
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A  
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER  
PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD.  
AOC INTERNATIONAL (EUROPE) GMBH OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY  
AND EXCLUSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) GMBH LIABILITY, WHETHER  
BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED  
THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO  
EVENT SHALL AOC INTERNATIONAL (EUROPE) GMBH BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF  
USE OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE.  
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY  
GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM  
COUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE  
MEMBER COUNTRIES OF THE EUROPEAN UNION.  
Information in this document is subject to change without notice.  
59  
Warranty Statement for North & South America (excluding Brazil)  
WARRANTY STATEMENT  
for AOC Color Monitors  
Including those Sold within North America as Specified  
Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of  
three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original date of consumer  
purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. ) will, at its option, either  
repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except  
as *stated below. The parts or product that are replaced become the property of EPI.  
In the USA to obtain service under this limited warranty, call EPI for the name of the Authorized Service Center  
closest to your area. Deliver the product freight pre-paid, along with the dated proof of purchase, to the EPI  
Authorized Service Center. If you cannot deliver the product in person:  
Pack it in its original shipping container (or equivalent)  
Put the RMA number on the address label  
Put the RMA number on the shipping carton  
Insure it (or assume the risk of loss/damage during shipment)  
Pay all shipping charges  
EPI is not responsible for damage to inbound product that was not properly packaged.  
EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is  
not responsible for any costs associated with the transportation of product across international borders. This  
includes the international borders of the countries within this warranty statements.  
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free  
* This limited warranty does not cover any losses or damages that occur as a result of:  
Shipping or improper installation or maintenance  
Misuse  
Neglect  
Any cause other than ordinary commercial or industrial application  
Adjustment by non-authorized source  
Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service Center  
Improper environment  
Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities  
This three-year limited warranty does not cover any of the product's firmware or hardware that you or any third  
party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.  
60  
 
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A  
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL  
FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR  
IMPLIED) APPLY AFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT  
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY  
NOT APPLY TO YOU.  
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE.  
EPI’ LIABILITY, WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICT LIABILITY, OR OTHER  
THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE  
BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF  
PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR  
CONSEQUENTIAL DAMAGE. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE  
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION  
MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.  
YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.  
In the United States of America, this limited warranty is only valid for Products purchased in the Continental United  
States, Alaska, and Hawaii.  
Outside the United States of America, this limited warranty is only valid for Products purchased in Canada.  
Information in this document is subject to change without notice.  
For more details, please visit:  
61  
Warranty Statement for AP  
LIMITED THREE-YEAR WARRANTY*  
AOC Color Monitors sold within AP  
AOC is one internal brand for its professional monitor ,TV technology ,affordable price and available  
service .Customer satisfaction-oriented is always what we are pursuing .  
We provide 3 years standard warranty for AOC monitor and 1-3 years standard warranty for AOC TV .However  
There is some slight warranty difference due to AOC different service strategic in different area/country ,so any  
question against warranty or any other AOC products warranty ,please leave the message via  
service.support@aoc.com .or check with the dealer or reseller in your country where you bought the product .We  
will response to you with top priority .  
AOC warrants this product to be free from defects in material and workmanship .  
During the warranty period, TPV will, at its option, either repair the defective product with new or rebuilt parts, or  
replace it with a new or rebuilt product at no charge except as *stated below. The defective products that are  
replaced become the property of AOC.  
*This limited warranty does not cover any losses or damages that occur as a result of  
Shipping or improper installation or maintenance  
Misuse or Neglect  
Any cause other than ordinary application  
Adjustment by non-authorized source  
Repair, modification, or installation of options or parts by anyone other than an AOC Authorized Service  
Center  
Improper environment- Excessive or inadequate heating or air conditioning or electrical powers failures,  
surges or other irregularities  
Fire, flood, earthquake, terrorist attack or other accidents  
This limited warranty does not cover any of the product firmware or hardware that you or any third party have  
modified or altered; customer bear the sole responsibility and liability for any such modification or alteration.  
It’s the right of AOC to issue or terminate the warranty terms. For exception cases, subject to report of our  
investigation, we reserve the right to terminate or modify terms of warranty policy.  
How to get your Warranty ?  
1. Please keep the purchase invoice ,and our service partner will take over the service against the invoice  
2. If you can not show the invoice ,please contact local dealer /.reseller for getting special support  
62  
 

GE 00008005 User Manual
FUNAI ET413E, ET419E User Manual
Electrolux Zanussi Professional FCF 4 User Manual
DFI U340 490 User Manual
Cypress CY7C1318CV18 267BZXC User Manual
Crucial Technology 960gb 2 5 Ssd M500 CT960M500SSD1 User Manual
Casio DQ 584B User Manual
BT SYNERGY 4000 User Manual 1
Antec Three Hundred User Manual
Acer LCD Monitor UM VH6AA 003 User Manual