OW N ER' S M A N UA L
This owne r's m a nua l for CDX-3 5 ,
CDX-3 5 C a nd CDX-3 5 P .
VESTAX CORPORATION
1-18-6 Wakabayashi, Setagaya-ku, Tokyo 154-0023 Japan
Phone:03-3412-7011 Fax:03-3412-7013
VESTAX America
2750C 29th Ave Suite. 115 Hollywood. Fl33020
Phone:303-766-5269 Fax:303-766-2196
(
)
VESTAX Europe Ltd.
Unit 5 Riverwey Industrial Park Alton, Hampshire GU34 2QL England
Phone:44-1420-83000 Fax:44-1420-80040
N O T E
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequeney energy
and, If not installed and used in accordance with the lnstructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment dose cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
●
●
●
Reorient or relocate the recelving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
●
Consult the dealer or an experiencced radio/TV technician for help.
N O T E
Changes or modifications may cause this unit to fail to comply wiht Part 15 of the
FCC Rules and may void the user's authority to operate the equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la Classe B respecte toutesles exigences du Réglement sur le matérier brouilleur du
Canada.
HOW TO CONNECT A PLUG
IMPORTANT
The wires in the mains lead are coloured in
accordance with the following code:
BLUE-"NEUTRAL"("N")
This apparatus is fitted with an approved moulded 13
Amp plug.To change a fuse in this type of plug
proceed as follows:
BROWN-"LIVE"(L")
1.Remove fuse cover and fuse.
1.The BLUE wire must be connected to the terminal
which is marked with the letter "N" or coloured
BLACK.
2.Fix new fuse which should be a BS1362 5A.
A.S.T.A. or BSI approved type.
3.Refit the fuse cover.
2.The BROWN wire must be connected to the
terminal which is marked with the letter "L" or
coloured RED.
3.Do not connect either wires to the earth terminal in
the plug which is marked by the letter "E" or by the
If the fitted plug is not suitable for your sockel
outlets, It should be cut off and an appropriate plug
fitted in its place. It the mains plug conlains a fuse.
this should have a value of 5A. If a plug without a
fuse is used, the fuse at the distribution board
should not be greater than 5A.
safely earth symbol
and-yellow.
↓or coloured green or green-
N O T E
Betore replacing the plug cover, make cenain that the
cord grip is clamped over the sheath of the lead-not
simply over the two wires.
The severed plug must be destroyed to
avoid a possible shock hazard it be
inserted into a 13A socket elsewhere.
CLASS
1
LASEN PNOOCUT
LUOKAN 1 LASENLAITE KLASS 1
LASENAPPANAT
42
IM P O R T A N T S A F E G U A R D S
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to meet strict quality and
safety standards. There are, however, some installation and operation
precautions which you should be particularly aware of.
1. Read instructions-All the safety and operating
instructions should be read before the appliance
is operated.
unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
10. Power sources-This product should be operated
only from the type of power source indicated on
the marking label. If you are not sure of the type
of power supply to your home, consult your
appliance dealer or local power company.
2. Retain instructions-The safety and operating
instructions should be retained for future
reference.
3. Heed Warnings-All warnings on the appliance
and in the operating instructions should be
adhered to.
11. Grounding or Polarization-This product is
equipped with a polarized alternating-current
(
line plug a plug having one blade wider than the
4. Follow Instructions-All operating and use
instructions should be followed.
)
other . This piug will fit into the power outlet
only one way. This is safety feature. If you are
unable to insert the plug fully into the outlet, try
reversing the plug. If this should still fail to fit,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
polarized plug.
5. Cleaning-Unplug this product from the wall
outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for
cleaning.
6. Attachments-Do not use attachments not
recommended by the product manufacturer as
they may cause hazards.
12. Power-Cord Protection-Power supply cords
should be routed so that they are not likely to be
walked on or pinched by intems placed upon or
against them, paying particular attention to cords
at plugs, convenience receptacles, and the point
where they exit from the appliance.
7. Water and Moisture-Do not use this product near
water-for example, near a dath tub, wash bowl,
kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, and the like.
13. Protective Attachment Plug-The appliance is
equipped with an attachment plug having
overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting
of protective device. If replacement of the plug
is required, be sure the service technician has
used a replacement plug specified by the
manufacturer that has the same overload
protection as the original plug.
8. Accessories-Do not place this product on an
unstable cart, stand, tripod, or table. The product
may fall, causing serious injury to a child or
adult, and serious damage to the appliance. Use
only with a cart,. stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
product. Any mounting of the appliance should
follow the manufacturer's instructions, and
sholud use a mounting accessory recommended
by the manufacturer.
14. Lightning-For added protection for this product
during lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet. This will prevent
damage to the product due to lightning and
power-line surges.
9. Ventilation-Slots and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating, and these openings must not be
blocked or covered. The openings should never
be blocked by placting the product on a bed, sofa,
rug, or other similar surface. This product should
never be placed near or over a radiator or heat
register. This product should not be placed in a
built-in installation such as a bookcase or rack
15. Overloading-Do not overload wall outlets and
extension cords as this can result in a risk of fire
or electric shock.
3
to its normal operation.
e. If the product has been dropped or cabinet has
been damaged.
16. Object and Liquid Entry-Never push objects of
any kind into this product through openings as
they may touch dangerous voltage points or
short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on
the product.
f. When the product exhibits a distinct change in
perfromance-this indicates need for service.
19. Replacement Parts-When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characterristics as the original parts.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
17. Servicing-Do not attempt to service product
yourself as opening or removing covers may
expose you to dangerrous voltage or other
hazards. Refer all servicing to qualified
sersonnel.
20. Safety Check-Upon completion of any service or
repairs to product, ask the service technician to
perfrom sefety checks to determine that the
product is in proper operating condition.
21. Carts and Stands-The appliance should be used
only with a cart stand that is recommended by
manufacturer.
18. Damage Requiring Service-Unplug this product
from the wall outlet and refer servicing to
qualified service personnel under the following
conditions:
a. When the power-supply cord or plug is
damage.
b. If liquid has been spilled or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product dose not operate normally by
following the operating instructions. Adjust
only those controls that are coverd by the
operating instructions as an improper
adjustment of other, controls may result in
damage and will often require extensive work
by a qualified technician to restore the product
22. An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.
F E ATU R E S
and play around with the loop on the fly.
●Master tempo / master key
●Analog-touch cueing system
Thanks to a large buffer memory and ultra-fast DSP,
the cue point can be searched for with a jog wheel,
just like an analog player. The sound is produced as
the wheel is spun, back and forth, slow or fast, just
like cueing vinyl. The new way of CD cueing, point
focus an alternative way of cueing is also provided.
The CDX-35 produces a short loop of sound around
the laser pick up, just like any other CD player. The
difference with the CDX-35 is that the length can be
adjusted from 0.013 to 3 seconds. Therefore, exactly
one beat, half bar or full bar can be monitored in a
loop and the loop can be moved around. This
advanced monitor system makes the CD cueing no
longer a pain but fun.
In addition to regular pitch control, the CDX-35
offers two advanced tempo and key controls. Thanks
to the DSP technology, the tempo can be changed +-
10% without changing the key, and the key can be
changed +-20% without changing the tempo. This
feature allows DJs to mix music in perfect pitch and
key.
●Reverse play
The CDX-35 even plays music in reverse. The
special technique, which was only possible with a
special analog turntable is now available by just
touching a button.
●Three plus one instant cue positions
The CDX-35 also offers more playability with the
total of four cue / memory points. This feature makes
the CDX-35 almost endless multi-sampling machine.
●Seamless loop
Up to 20 seconds of sound can be looped
instantaneously by pressing buttons. Dedicated start,
stop and re-loop / exit buttons allow the DJs to create
84
BEFO RE U SE
Notes on the Compact Disc (CD)
The surface which is glossy like a ralnbow is the front side of the CD, and the surface where the label
information is printed is the back side.
Unlike conventional analog disk turntables, the CD player reads information from the disc by applying laser
beam, in place of a stylus, on the front surface. Consequently, the performance of CD discs will not degrade
after repeated use like conventional analog disks.
■Handle the CD disc carefully so as not to damage the front surface.
■To maintain the CD disc flawless, do not place it in the following locations.
●In a place subject to direct sunlight or near a heat source such as a room heater.
●In a place subject to excessive moisture or dirt.
●In a place which may be subject to rain, for example near a window.
■Keep the disc surface always clean.
UP to about 6 billion items of data are recorded on the Cd disc surface. When cleaning the disc surface,
always use a specialized CD cleaner product and wipe in the direction as shown below.
●Wipe in the radial direction.
●Do not wipe in the circumference direction.
●Never use record cleaner designed for conventional analog disks, for this may degrade the CD disc surface.
■Always store disc properly in the case.
5
CONTROL AND FUNCTION
CONTROLLER UNIT
PLAYER UNIT
162
CONTROLLER UNIT
1 2
1 7
1 8 1 9
1 6
5
2 2
2 3
6
2 4
2 7
2 6
2 0
8
7
2 1
1 1
2 5
1 0
1 3
1 4
9
1 5
4
3
1
2
7
next track. The number of tracks skipped ahead.
① PLAY/PAUSE KEY
Each press of the PLAY/PAUSE button cause the
operation to change from play to pause or from pause
to play.
⑧ PREVIOUS KEY
Used for skipping backwards to the starting point of
the current track(one press). Pressing twice returns to
the starting point of the previous track. Pressing
additional times will return to the corresponding
previous track.
②CUE KEY
Pressing cue button returns the CD to the last set
"CUE" point and pauses it. The CUE point is either
the position at which "PLAY" was last actually
started or the "LOOP IN" point it was previously set.
Pressing the "CUE" button a second time allows the
music to be played from the "CUE" position until it is
released.
⑨ SEARCH DIAL
This search dial serves two functions depending on
the mode you are working in.
a, The search dial will act as a slow flame search
control when the CD is not playing but either
paused or set to a cue point.To set a new flame cue
point, spin the dial then press play when you have
determined the proper position. Press CUE to
return the 'CUE POINT'.
Repeatedly pressing the cue button allows the CD to
be played from the same position any number of
times. The CUE LED will light up from the time the
CUE button is pressed until the CD has reset to the
position at which play was started. Steady lighting of
this LED indicates the ready condition.
b, The search dial will temporarily bend the pitch of
the music up to +/- 10% if the song is already
playing by rotating the dial clockwise to speed up
or counterclockwise to slow down. The amount of
pitch change is determined by the speed of
rotation.
③ MONITOR KEY
When the monitor button is pressed during the
PAUSE mode ,a short loop sound of the paused
position is played back for monitoring. Then exact
position for the next start can be searched and set by
using the SEARCH DIAL.
⑩ PITCH CONTROLLER
The pitch can be changed up to +/- 10% by moving
sliding fader.
④ POINT FOCUS KEY
Used for changing time of monitor sound.
⑪ KEY CONTROL
The key can be change up to +/- 1 octave by rotating
⑤ CUE MEMORY
volume.
Press the cue memory button. The CUE BANK
indicater lights. You can select any cue bank. Press
BANK button (1,2,3).The controller memorizes cue
point.
⑫ MASTER TEMPO
Press the MASTER TEMPO button. The MASTER
TEMPO indicater lights. You can change the playing
speed by moving PITCH CONTOROLLER.
Even when the music's speed changes, the music
pitch does not change.
⑥ CUE MEMO 1,2,3 KEY
Used for setting and recall cuepoint.
⑦ NEXT KEY
Used for skipping forward to the starting point of the
8
21
⑬ LOOP START
◯ OPEN/CLOSE
Used for setting a start loop point and new cue
Press to load or eject the disc. Each press will open or
close the disc tray on the transport. Tray will not
open unless the disc has been paused.
point during play.
⑭ LOOP END
22
Used for setting the end loop point and and ◯ PLAYER SELECT SWITCH
releasing loop action.
The switch for select main player.
23
◯ SUB CUE
⑮ RELOOP/EXIT
Cue switch for second player unit.
This button is for cancel and return loop play .
24
During the loop play , press the RELOOP/EXIT ◯ SUB PLAY/PAUSE KEY
button. When playback reaches the loop out point ,
playback continues without returning to the loop in
point.
The play/pause switch for second player unit.
25
◯ PITCH INDICATER
Shows the present pitch value.
⑯ REVERSE
26
Press the REVERSE button. The REVERSE ◯ DISPLAY
indicater lights. The player starts reverse play.
During the reverse play, press REVERSE or STOP
button . Player will return normal playback.
Shows the information of playback. (Refer to
"DISPLAY")
27
◯ CONNECTOR
⑰ REPEAT
Plug your control cables for player unit.
Used to activate REPEAT mode. All repeat (Play
the next song and then repeat the whole CD) is
selected by pressing this button once. Single repeat
(repeat current song only) is selected by pressing
one more time. Repeat off is selected by one more
push.
⑱ DISPLAY KEY
Used to change DISPLAY MODE. Usually display
shows TRACK REMAIN TIME. TRACK
PLAYING TIME is selected by pressing button
once. DISC TOTAL REMAIN TIME is selected by
pressing one more time.
⑲ RING DISPLAY KEY
Used to change RING DISPLAY MODE.
⑳ STOP
Used to stop CD spinning.
9
DISPLAY
A MAIN PLAYER
G REVERSE
Shows the player (A or B) that the unit is selected.
Lights when the REVERSE function is used.
B TRACK
H REPEAT
Shows the track that the unit is playing.
Lights when repeat function is used. Shows present
repeat mode (repeat1/repeat all)
C TIME (MIN/SEC/FRM)
Shows the minutes/seconds/frames elapsed or I CUE MEMO 1,2,3
remaining depending on mode settings.
1 second = 75 frames
Lights when cue point is memorized in memory.
J MASTER TEMPO
D PITCH
Lights when the MASTER TEMPO function is used.
Shows present value of pitch.
K RING DISPLAY
E KEY
Shows present value of key.
Shows operation of playing disc . Press "RING
DISPLAY" , you can select 2 display mode.
F STAND-BY
Lights when the amount of data is stored in shock
proof memory.
10
[1] TIME MODE
Shows the time information of disc. In this mode, RING DISPLAY is working together time counter (TIME
DISPLAY ).
1. TRACK REMAIN TIME
2. TRACK PLAYING TIME
3. TOTAL REMAIN TIME
[2] DISK OPERATION MODE
Shows the operation of disc. In this mode, RING DISPLAY rotates in various speed and direction. Speed is
changed by playback speed. During normal playback, RING DISPLAY rotates clockwise. When REVERSE
mode is on, rotates counterclockwise.
211
PLAYER UNIT
●FRONT PANEL SECTION
2 9
2 8
3 2
3 3
3 0
3 1
3 4
3 5
3 6 3 7
to the starting point of the previous track. Pressing
additional times will return to the corresponding
previous track.
28
◯ POWER SWITCH
Turn on and turn off the machine from this button.
The unit should always be shut down with this button
first before any external power is removed.
◯34
NEXT KEY
Used for skipping forward to the starting point of the
next track. The number of tracks skipped ahead.
29
◯ DISK TRAY
Place your CD in here.
◯35
PLAY/PAUSE KEY
30
◯ LINK/TRACK DISPLAY
Each press of the PLAY/PAUSE button cause the
operation to change from play to pause or from pause
to play.
Connecting with controller, display shows setting of
player (A or B). Without controller, shows track
number.
◯
36
HEADPHONE LEVEL
Adjusts the headphone output level.
◯
31
OPEN/CLOSE KEY
Press to load or eject disc. each press will open or
close the disc tray on the transport.
note: Tray will not open unless the disc has been
stopped.
◯37
HEADPHONE JACK
Connect the headphones to this jack. Headphones
with its impedance from 8 ohm to 600 ohm can be
used.
◯32
STOP KEY
◯33
PREVIOUS KEY
Used for skipping backwards to the starting point of
the current track(one press). Pressing twice returns
212
●REAR PANEL SECTION
4 2
4 0
CD OUT
VES TAX CORP ORATION
MODEL NO.CDX-3 5
2 3 0 V～ 5 0 Hz 1 8 W
R
L
CLAS S 1 LAS ER P RODUCT�
KLAS S E1 LAS ER P RODUCT�
I.H.T. IEC8 2 5 �
�
MADE IN J AP AN
FABRIQUE AU J AP ON
S HOCK HAZARD, DO NOT REMOVE S CREWS .
CAUTION：�
CD B
CONTROLLER
MAX 5 V 0 .5 A
RIS QUE DE CHOC ELECTRIQUE,
NEP AS ENLEVER VIS .
�
ATTENTION：�
OP EN/
CLOS E
S ERIAL NO.
ON OFF
4 1
3 9
3 8
◯38
CONTROLLER CONNECTOR
◯41
OPEN/CLOSE LOCK
Plug your control cables for control unit.
When this switch is on, OPEN/CLOSE KEY of
player and controller is unavailable during playback.
◯39
PLAYER CONNECTOR
Plug your control cable for second player unit.
◯42
AC POWER CABLE
Should be plugged into your power outlet.
◯40
CD OUT JACK (RCA)
Connect your CD player to your mixer from this line
level output.
193
TECHNIQUES FOR DJ PLAY
CUEING OPERATIONS (setting a cue point)
[1] USE PAUSE MONITOR FUNCTION
PAUSE
①
①
During playback, when the disc comes to the
point you wish to cue, press the
PLAY/PAUSE and MONITOR button to
enter monitor mode.
“PLAY/PAUSE”
CUE POINT
direction of play back
②Adjust the length of monitoring sound
②
(0.039s ~ 3.0 s).
“MONITOR”
adjust the length of
monitoring sound
③Rotate the search dial to search for desired
③
location.
A
B
B
A
④When the flame number or the audiable
sound reaches the desired cueing point, press
the PLAY/PAUSE button. The cue point has
been stored in memory.
④⑤⑥
⑤During playback, press the "CUE" button.
The player's pickup will return to set the cue
point and enter the pause mode.
PLAY/PAUSE
⑥Press the PLAY/PAUSE button. Playback
will begin instantly from the cue point.
the cue point set
14
[2] USE THE SEARCH DIAL
①
①During playback, press the PLAY/PAUSE
button.
PAUSE
PLAY/PAUSE
CUE POINT
direction of play back
②Rotate the jog dial to search for desired
location. (Playback speed is changing from
0% to +/- 300% by rotating speed.)
②③
B
A
B
③To set the cue point while listening to the
sound, using the search dial to return the disc
to a point just before the point at which you
wish to begin playback from the cue.(The
sound heard in the audible pause mode is the
cue point.)
A
④When the flame number or the audiable
sound reaches the desired cueing point, press
the PLAY/PAUSE button. The cue point has
been stored in memory.
④⑤
During playback, press the "CUE" button.
The player's pickup will return to set the cue
point and enter the pause mode.
the cue point set
⑤Press the PLAY/PAUSE button. Playback
will begin instantly from the cue point.
15
CUE POINT MEMORY
One player of CDX - 35 can memorize 3 cue points.
[1] Setting the cue point memory
①②
①Set the cue point. (See the " cueing
operation")
②Press the "MEMO" button. The " 1 2 3 "
indicator lights on and off.
1
2
3
③Select any memory bank, and press bank
button.(EX : BANK 1)
③④
④The bank indicator lights. (EX: BANK 1)
The cue point has been stored in memory
bank.
[2] Recall the cue point memory
①Press the bank button (The cue point is already set.)
②Press the "CUE" button , the player's pickup will return to set the cue point and enter the pause mode.
③Press the PLAY/PAUSE button. Playback will begin instantly from the cue point.
[3] Clear the cue point memory
①When you press " STOP " button twice, the cue point memory is cleared.
②Turn off power of CDX-35, the cue point memory is cleared too.
16
LOOP PLAY
[1] DESIGNATE A LOOP
①
Press the PLAY /PAUSE button to begin playback.
Press the "START" button at the desired loop in point.
The START button lights, and the END ,RELOOP/EXIT
button lights on and off.
set loop-in point
①②
②
S
direction of playback
③④
set loop
out point
MAXIMUM 20 second
③
As playback continues, press the "END" button at the loop
S
E
out point.
The END button lights.
�
LOOP
④Loop play begins automatically (between the loop-in and
loop-out points).
back
⑤
⑤During the loop play, press the "START" button. The
player's pickup will return to set the loop in point and
continues loop play.
S
E
LOOP
[2] CHANGE THE LOOP END POINT
[3] CANCEL /RETURN LOOP PLAY
During loop play, press the "RELOOP/EXIT" button. Loop
play is canceled.
A
B
S
When playback reaches the loop out point, Playback
continues without returning to the loop in point. After
canceling loop play, press the "RELOOP/EXIT" button
during playback. Playback will return to the previously set
loop and loop play will be resumed (reloop).
LOOP
A
B
adjust end pointby
pressing A or B button
During the loop play, press the "NEXT"
or "PREVIOUS" button.
The loop out point moves in 1-flame
increments.
117
MASTERTEMPO
Press the MASTER TEMPO button. The MASTER TEMPO
indicator lights.
PITCH INDICATER
Shows position of memorized tempo by LED.
Please refer to following example.
1
◯
2
◯
3
◯
4
◯
P LAYS ELECT
Cha ng e t o �
t he B s ide .
Cha ng e �
P LAYERS ELECT �
�
S W from A t o B
Adjus t t he t e m po�
（e x.t e m po：-6 ％）�
Adjus t t he t e m po�
（e x.t e m po：0 ％）�
（e x. pla ye r A）�
（e x. pla ye r B）�
5
◯
6
◯
Cha ng e t o �
t he As ide .
t urn off t he LED you c a n�
c ont roll pit c h norm a lly
P re s e nt fa de r pos it ion：0 ％�
�
Me m orize d t e m po：-6 % �
ke e p m e m orize d �
t e m po（：-6 ％）
（e x. pla ye r A）�
�
�
�
P it c h indic a t e r �
lig ht s on m inus s ide
Whe n t he pit c h c ont rolle r re t urn t he pos it ion
of m e m orize d t e m po（：-6 ％）, t he m e m orize d
t e m po is re le a s e .
The pit c h indic a t e r s hows whic h s ide of pre s e nt
fa de r pos it ion m e m orize d t e m po is s e t .
108
CONNECTION
One Player and One Controller
Player CDX-35P
C
O
N
T
R
O
L
L
E
R
Controller CDX-35C
Two Player and Controller
Player CDX-35P
CD, B
CONTROLLER
CONTROLLER
Controller CDX-35C
Player CDX-35P
Connection for another EQUIPMENTS
CONTROLLER
CD OUT
CD, B
LINE
4, 5
LINE
1, 2
CONTROLLER
CD OUT
Controller CDX-35C
INPUT
MASTER OUT
MAIN SPERKER
MAIN SPERKER
Power amplifier [Vestax PT-X1000A]
CHANNEL
A
CHANNEL
B
PROTECT B.T.L
POWER
PEAK
PEAK
POWER
INPUT
INPUT
ON / OFF
MINI
MAX
MINI
MAX
Sperker cable
Sperker cable
DJ MIXER PMC-170A
19
SPECIFICATION
Total Power requirement
Weigth
115V/230VAC, 18W
0.8kg(Controller),
2.4kg(Player)
Demensions (WxHxD)mm
Attachments
210x49x165(Controller)
190x82x257(Player)
Owner's manual
(CDX-35, CDX-35C, CDX-35P)
Connector cable
(CDX-35, CDX-35P)
Quantization
16bit linear
Sampling Frequency
Digital Filter
44.1kHz
8times over sampling
16Mbit,10sec
CIRC
Shock Proof Memory
Error Correcting System
Harmonic Distortion
Frequency response
Signal To Noise Ratio
Channel Separation
CD OUT
Less than 0.011%
20Hz～20KHz
More than 96dB
More than 85dB
2Vrms
HEADPHONE LEVEL
0.6Vrms(1%THD)
20
443 S 851250
Vestax Corporation
|