Samsung GH68 07973A User Manual

X200.book Page 1 Friday, October 14, 2005 10:31 AM  
*
Depending on the software installed or your service provider or country,  
some of the descriptions in this guide may not match your phone exactly.  
* Depending on your country, your phone and accessories may appear  
different from the illustrations in this guide.  
Printed in India  
Code No.:GH68-07973A  
English. 10/2005. Rev 1.0  
World Wide Web  
X200.book Page 3 Friday, October 14, 2005 10:31 AM  
Drive safely at all times  
Do not use a hand-held phone while driving. Park  
the vehicle first.  
Switch off the phone when refuelling  
Do not use the phone at a refuelling point (service  
station) or near fuels or chemicals.  
Important  
safety  
Switch off in an aircraft  
Wireless phones can cause interference. Using them  
in an aircraft is both illegal and dangerous.  
precautions  
Switch off the phone near all medical  
equipment  
Failure to comply with the following  
precautions may be dangerous or illegal.  
Hospitals or health care facilities may be using  
equipment that could be sensitive to external radio  
frequency energy. Follow any regulations or rules in  
force.  
X200.book Page 1 Friday, October 14, 2005 10:31 AM  
Interference  
Keep your phone away from small children  
All wireless phones may be subject to interference,  
which could affect their performance.  
Keep the phone and all its parts, including accessories,  
out of the reach of small children.  
Be aware of special regulations  
Accessories and batteries  
Meet any special regulations in force in any area and  
always switch off your phone whenever it is forbidden  
to use it, or when it may cause interference or danger.  
Use only Samsung-approved accessories and  
batteries. Use of any unauthorised accessories could  
damage your phone and may be dangerous.  
• The phone could explode if the battery is  
replaced with an incorrect type.  
• Dispose of used batteries according to the  
manufacturer’s instructions.  
Water resistance  
Your phone is not water-resistant. Keep it dry.  
Sensible use  
Use only in the normal position (held to the ear). Avoid  
unnecessary contact with the antenna when the phone  
is switched on.  
Qualified service  
Only qualified service personnel may repair your  
phone.  
Emergency calls  
For more detailed safety information, see "Health and  
safety information" on page 60.  
Key in the emergency number for your present  
location, then press  
.
1
X200.book Page 2 Friday, October 14, 2005 10:31 AM  
About this Guide  
Tri-band operation  
This User’s Guide provides you with condensed  
information about how to use your phone. To quickly  
learn the basics for your phone, please refer to “Get  
started” and “Step outside the phone.”  
Use your phone in worldwide GSM networks, in  
any of 900, 1800, and 1900 bands.  
In this guide, the following instruction icons appear:  
Special  
features of your phone  
Indicates that you need to pay careful  
attention to the subsequent information  
regarding safety or phone features.  
Simple, compact design with Intenna  
Indicates that you can get more information  
on the referenced page.  
Samsung’s powerful intenna technology allows  
the best call quality without an annoying  
external antenna.  
Indicates that you need to press the  
Navigation keys to scroll to the specified  
option and then select it.  
IrDA  
Send and receive Phonebook  
data via an infrared port.  
Indicates a key on the phone. For example,  
[
]
[
]
Indicates a soft key, whose function is  
< >  
displayed on the phone screen. For example,  
<Menu>  
2
X200.book Page 3 Friday, October 14, 2005 10:31 AM  
Web browser  
Calendar and to do list  
Keep track of your daily and  
monthly schedules and tasks.  
Access the wireless web to get  
current information and up-to-  
the-minute a wide variety of  
media content.  
Alarm  
Use your phone as an alarm  
clock to wake you up in the  
morning or notify you to an  
event.  
Java  
Enjoy Java-based embedded  
games and download new  
games.  
Calculator  
Perform basic calculations and  
do currency conversions.  
Phonebook  
Store home, office, or cellular  
phone numbers for your entries.  
Multimedia Message Service (MMS)  
Send and receive MMS messages with a  
combination of text, images, and sounds.  
Voice recorder  
Record memos or sounds.  
3
X200.book Page 4 Friday, October 14, 2005 10:31 AM  
Send messages...................................................... 16  
View messages....................................................... 18  
Contents  
Enter text  
19  
22  
27  
58  
Unpack  
6
6
ABC, T9, Number, and Symbol mode  
Call functions  
Your phone  
Buttons, features, and locations  
Get started  
Advanced calling features  
Menu functions  
7
First steps to operating your phone  
All menu options listed  
Solve problems  
Install and charge the phone..................................... 7  
Power on or off........................................................ 8  
Keys and display ..................................................... 9  
Access menu functions ............................................ 11  
Customise your phone............................................. 12  
Make/Answer calls .................................................. 14  
Help and personal needs  
Health and safety information  
60  
67  
Step outside the phone  
14  
Index  
Begin with games, web, messages, and other special  
features  
Play games............................................................ 14  
Browse the web...................................................... 15  
Use Phonebook....................................................... 16  
4
X200.book Page 5 Friday, October 14, 2005 10:31 AM  
Overview of menu functions  
To access Menu mode, press <Menu> in Idle mode.  
1 SIM AT  
2
p. 27  
4 Sound settings  
p. 32  
6 Funbox  
p. 42  
8 Phonebook  
p. 50  
1 Ring tone  
2 Ring volume  
3 Alert type  
4 Keypad tone  
5 Message tone  
6 Alert on call  
7 Folder tone  
8 Power on/off  
9 Extra tones  
p. 32  
p. 32  
p. 32  
p. 32  
p. 32  
p. 33  
p. 33  
p. 33  
p. 33  
1 WAP browser  
2 Games  
3 Sounds  
4 Images  
5 Delete all  
6 Memory status  
p. 42  
p. 44  
p. 45  
p. 45  
p. 45  
p. 45  
1 Search  
p. 50  
p. 50  
p. 51  
p. 51  
p. 51  
p. 52  
p. 52  
p. 52  
2 New entry  
3 Group search  
4 Edit group  
5 Speed dial  
6 Delete all  
7 Memory status  
8 SDN*  
2 Call records  
p. 27  
1 Missed calls  
2 Received calls  
3 Dialled calls  
4 Delete all  
p. 27  
p. 28  
p. 28  
p. 28  
p. 28  
p. 28  
7 Organiser  
p. 46  
5 Call time  
6 Call cost*  
1 Alarm  
2 Calendar  
3 Time & Date  
4 Calculator  
5 To do list  
6 Voice memo  
7 Currency exchange  
p. 46  
p. 46  
p. 47  
p. 48  
p. 48  
p. 49  
p. 49  
9 Phone settings  
p. 53  
5 Messages  
p. 33  
3 Network services  
p. 29  
1 Infrared activate  
2 Display settings  
3 Greeting message  
4 Own number  
5 Language  
6 Security  
7 Extra settings  
8 Short cut  
p. 53  
p. 54  
p. 55  
p. 55  
p. 55  
p. 55  
p. 57  
p. 57  
p. 57  
1 Text messages  
2 Multimedia  
messages  
p. 33  
p. 37  
1 Call diverting  
2 Call barring  
3 Call waiting  
4 Network selection  
5 Caller ID  
6 Closed user group  
7 Band selection  
p. 29  
p. 30  
p. 30  
p. 30  
p. 31  
p. 31  
p. 31  
3 Push messages  
p. 41  
9 Reset settings  
*Shows only if supported by your  
SIM card.  
5
X200.book Page 6 Friday, October 14, 2005 10:31 AM  
Unpack  
Your phone  
Make sure you have each item  
Buttons, features, and locations  
Earpiece  
Display  
Phone  
Travel adapter  
User’s guide  
Navigation keys  
(Up/Down/Left/  
Right)  
Web access/  
Confirm key  
Headset jack  
Left soft key  
Volume keys  
Right soft key  
Battery  
Power on/off/  
Menu exit key  
You can obtain various accessories from your local  
Samsung dealer.  
Dial key  
Cancel/Correct  
key  
Alphanumeric  
keys  
The items supplied with your phone and the accessories  
at your Samsung dealer may vary, depending on your  
country or service provider.  
Special  
function keys  
Microphone  
Infrared port  
6
X200.book Page 7 Friday, October 14, 2005 10:31 AM  
Get started  
Install the battery.  
Replace the cover.  
First steps to operating your phone  
SIM card information  
When you subscribe to a cellular network, you receive  
a plug-in SIM (Subscriber Identity Module) card  
loaded with your subscription details, such as your  
PIN, and available optional services.  
Install and charge the phone  
Plug the travel adapter  
into the phone.  
Plug the adapter into  
a standard AC wall  
outlet.  
Remove the battery  
cover.  
Insert the SIM card.  
If the phone is already  
on, first turn it off by  
Make sure that the  
gold-coloured contacts  
on the card face down  
into the phone.  
holding [  
].  
7
X200.book Page 8 Friday, October 14, 2005 10:31 AM  
Get started  
Power on or off  
When the phone is completely charged (the  
battery icon becomes still), unplug the adapter  
from the power outlet.  
Power on  
1. Open the phone.  
2. Press and hold [ ] to turn on  
the phone.  
Remove the adapter from the phone.  
Do not turn on  
the phone when  
mobile phone  
3. If necessary, enter the PIN and  
use is prohibited.  
press <OK>.  
Power off  
1. Open the phone.  
Low battery indicator  
2. Press and hold [ ].  
When the battery is low:  
a warning tone sounds,  
the battery low message displays, and  
the empty battery icon  
blinks.  
If the battery level becomes too low, the phone  
automatically turns off. Recharge your battery.  
8
X200.book Page 9 Friday, October 14, 2005 10:31 AM  
Keys and display  
Keys  
End a call.  
Press and hold to switch the phone on or off.  
In Menu mode, cancel input and return the  
phone to Idle mode.  
Perform the function indicated on the bottom  
line of the display.  
Enter numbers, letters, and some special  
characters.  
In Idle mode, press and hold [1] to access  
In Idle mode, access your favourite menus  
directly.  
p. 57  
In Menu mode, scroll through menu options.  
your voicemail server. Press and hold [  
0] to  
enter an international call prefix.  
Enter special characters.  
In Idle mode, launch the web browser.  
In Menu mode, select the highlighted menu  
option or confirm input.  
In Idle mode, press and hold  
or deactivate Silent mode. Press and hold  
to enter a pause between numbers.  
[
]
to activate  
[
]
Make or answer a call.  
In Idle mode, retrieve the recent numbers  
dialled, missed, or received.  
Adjust the phone volume.  
In Idle mode, adjust the keypad tone  
volume.  
Delete characters from the display.  
In Menu mode, return to the previous menu  
level.  
9
X200.book Page 10 Friday, October 14, 2005 10:31 AM  
Get started  
Display  
IrDA feature activep. 53  
Icons  
(continued)  
Layout  
Roaming  
Icons  
display various icons.  
New text message  
New voicemail message  
Text and graphics  
display messages,  
instructions, and  
New multimedia message  
Active Silent mode or call ringer set  
information you enter.  
to vibrateꢀ  
p. 13, p. 32  
Soft key function  
Mute mode  
p. 25  
Menu Phonebook  
indicators  
show the current functions  
assigned to the two soft  
keys.  
Alarm set  
Battery power level  
Received signal strength  
Call in progress  
Icons  
Out of your service area; you  
cannot send or receive calls  
GPRS network  
Call diverting feature active  
p. 29  
10  
X200.book Page 11 Friday, October 14, 2005 10:31 AM  
Access menu functions  
Select an  
option  
1. Press the appropriate soft key.  
Use the soft  
keys  
The roles of the soft keys vary  
depending on the function you are  
using. The bottom line of the  
2. Press the Navigation keys to  
move to the next or previous  
option.  
display indicates their current role.  
Menu  
Phonebook  
3. Press <Select>, <OK>, or  
[
]
to confirm the function  
displayed or option highlighted.  
4. To exit, choose either of the  
following methods:  
Press < > or [  
up one level.  
C] to move  
Press the left soft  
key to access  
Menu mode.  
Press the right soft  
key to access the  
Phonebook menu.  
Press [ ] to return to Idle  
mode.  
Use shortcuts Press the number key  
corresponding to the option you  
want.  
11  
X200.book Page 12 Friday, October 14, 2005 10:31 AM  
Get started  
Customise your phone  
You can set wallpaper for the idle  
screen.  
Idle mode  
wallpaper  
1. In Idle mode, press <Menu  
>
Display  
language  
1. In Idle mode, press <Menu  
>
and select Phone settings  
Language  
and select Phone settings  
.
Display settings  
2. Select a language.  
Wallpaper Wallpaper list  
.
2. Select the image you want.  
1. In Idle mode, press <Menu  
>
Call ringer  
melody and  
volume  
and select Sound settings  
3. Press <Select>.  
Ring tone  
.
2. Select a ringtone.  
3. Select Ring volume  
.
4. Adjust the volume level.  
5. Press <OK>.  
12  
X200.book Page 13 Friday, October 14, 2005 10:31 AM  
You can set the Navigation keys as  
shortcuts to access your favourite  
menus.  
You can protect the phone against  
unauthorised use with a phone  
password. The phone will require  
the password on power-up.  
Phone lock  
Menu  
shortcuts  
1. In Idle mode, press <Menu  
>
and select Phone settings  
1. In Idle mode, press <Menu  
>
Short cut  
.
and select Phone settings  
Security  
password  
2. Enter the default password,  
.
Change  
2. Select a key.  
3. Select a menu to be assign to  
the key.  
00000000, and press <OK>.  
3. Enter a new 4- to 8-digit  
You can switch the phone to Silent  
mode to avoid disturbing other  
people with your phone sounds.  
Silent mode  
password and press <OK>.  
4. Enter the new password again  
and press <OK>.  
Press and hold [ ] in Idle mode.  
5. Select Phone lock  
6. Select Enable  
7. Enter the password and press  
OK>.  
.
.
<
13  
X200.book Page 14 Friday, October 14, 2005 10:31 AM  
Make/Answer calls  
Step outside the phone  
Begin with games, web, messages, and other special  
features  
1. Enter an area code and phone  
Make a call  
number.  
Play games  
2. Press [ ].  
3. To end the call, press [ ].  
1. In Idle mode, press <Menu  
>
Launch a game  
and select Funbox  
a game.  
2. Select START GAME  
Games  
1. When the phone is ringing,  
Answer a call  
press [ ].  
.
2. To end the call, press [ ].  
3. Select a game mode or press  
any key to start the game.  
Press [ / ].  
Adjust the  
volume during  
a call  
14  
X200.book Page 15 Friday, October 14, 2005 10:31 AM  
Browse the web  
1. Press the Navigation keys to  
move the selection.  
Play  
BubbleSmile  
Using a built-in web browser, you can get easy access  
to the wireless web to get a variety of up-to-date  
services and information and to enjoy downloads of  
web content.  
2. Press [1] or [3] to make a  
horizontal or vertical line of  
three identical bubbles.  
In Idle mode, press [  
].  
Launch the  
1. Press the Navigation keys to  
move the selection to the  
position you want to connect  
the pipe.  
web browser  
Play Fun2Link  
To scroll through browser items,  
press [Up] or [Down].  
Navigate the  
browser  
2. Press [  
] to insert a pipe.  
3. Repeat until you complete the  
pipeline.  
To select an item, press [  
].  
To return to the previous page,  
press [ ].  
C
To access browser options,  
press and hold [ ].  
15  
X200.book Page 16 Friday, October 14, 2005 10:31 AM  
Step outside the phone  
Use Phonebook  
1. In Idle mode, press  
Phonebook> and select  
Search  
Find an entry  
<
To the phone’s memory:  
Add an entry  
.
1. In Idle mode, enter a phone  
2. Select an entry.  
number and press <Save>.  
3. Scroll to a number and press  
2. Select a number type.  
[
<
] to dial, or press  
Options> to access options.  
3. Select Phone  
.
4. Enter a name and press <OK>.  
5. Press <OK> to save the entry.  
To the SIM card:  
Send messages  
1. In Idle mode, press <Menu  
and select Messages Text  
messages Write new  
2. Enter the message text.  
3. Press <Options> and select  
>
Send a text  
message (SMS)  
1. In Idle mode, enter a phone  
number and press <Save>.  
.
2. Select a number type.  
3. Select SIM  
.
Save and send or Send only  
.
4. Enter a name and press <OK>.  
4. If you selected Save and send  
,
5. Press <OK> to save the entry.  
select a memory location.  
5. Enter a destination number and  
press <OK>.  
16  
X200.book Page 17 Friday, October 14, 2005 10:31 AM  
1. In Idle mode, press <Menu  
and select Messages  
Multimedia messages  
Write new  
>
7. Enter a destination number or  
address, or select a number  
from Phonebook and press  
Send a  
multimedia  
message  
(MMS)  
.
<OK>.  
2. Enter the message subject  
8. To add other destinations,  
select Add destination and  
repeat from step 6.  
press <OK>.  
3. Select Add here and add  
message contents.  
9. To add destinations of other  
types, press < > and repeat  
from step 5.  
4. When you have finished, press  
Options> and select Send  
5. Select a destination type.  
6. Select one of Phone number  
E-mail address, or  
Phonebook  
<
.
10.When you have finished, select  
Send message  
.
,
.
17  
X200.book Page 18 Friday, October 14, 2005 10:31 AM  
Step outside the phone  
View messages  
When a notification appears:  
1. Press <View>.  
View a  
multimedia  
message  
When a notification appears:  
View a text  
2. Press <Options> and select  
1. Press <View>.  
message  
Retrieve  
.
2. Select a message from the  
Inbox.  
3. Select a message from the  
Inbox.  
From the Inbox:  
From the Inbox:  
1. In Idle mode, press <Menu  
>
Text  
1. In Idle mode, press <Menu  
>
and select Messages  
messages Inbox  
2. Select the message.  
and select Messages  
Multimedia messages  
Inbox  
2. Select the message.  
.
.
18  
X200.book Page 19 Friday, October 14, 2005 10:31 AM  
: Number mode  
Enter text  
None: Symbol mode  
ABC, T9, Number, and Symbol mode  
Using ABC mode  
Press the appropriate key until the character you want  
appears on the screen.  
You can enter text for some features such as  
messaging, Phonebook, or Organiser, using ABC  
mode, T9 mode, Number mode, and Symbol mode.  
Characters in order displayed  
Key  
Changing the text input mode  
The text input mode indicator displays when the  
cursor is in a text field.  
Upper case  
Lower case  
Write new  
Text input mode  
indicator  
Options  
Press the right soft key to change the input mode:  
space  
: ABC mode  
: T9 mode  
19  
X200.book Page 20 Friday, October 14, 2005 10:31 AM  
Enter text  
Tips for using ABC mode  
Using T9 mode  
T9 is a predictive text input mode that allows you to  
key in any character using single keystrokes.  
To enter the same letter twice or to enter a  
different letter on the same key, wait for the cursor  
to move to the right automatically or press [Right].  
Then, enter the next letter.  
Entering a word in T9 mode  
1. Press [  
each key once for each letter.  
For example, press [ ], [ ], [  
enter Hello in T9 mode.  
2] to [9] to start entering a word. Press  
Press [ ] to insert a space.  
Press [ ] to change case. Initial capital ( ),  
Capital lock ( ), and Lower case (  
available.  
4
3
5], [5], and [6] to  
) are  
T9 predicts the word that you are typing, and it  
may change with each key that you press.  
Press the Navigation keys to move the cursor.  
Press [ ] to delete characters one by one. Press  
and hold [ ] to clear the display.  
C
2. Enter the whole word before editing or deleting  
characters.  
C
3. When the word displays correctly, go to step 4.  
Otherwise, press [  
choices for the keys that you have pressed.  
For example, Of and Me use [ ] and [ ].  
0] to display alternative word  
6
3
4. Press [ ] to insert a space and enter the next  
word.  
20  
X200.book Page 21 Friday, October 14, 2005 10:31 AM  
Tips for using T9 mode  
Using Number mode  
Number mode enables you to enter numbers.  
Press [1] to enter periods or apostrophes  
automatically.  
Press the keys corresponding to the digits you want.  
Press [ ] to change case. Initial capital ( ),  
Capital lock ( ), and Lower case (  
available.  
) are  
Using Symbol mode  
Symbol mode enables you to insert symbols.  
Press [Left] or [Right] to move the cursor.  
Press [ ] to delete characters one by one. Press  
and hold [ ] to clear the display.  
C
To  
Press  
C
display more symbols  
select a symbol  
[Up] or [Down].  
Adding a new word to the T9 dictionary  
This feature may not be available for some languages.  
1. Enter the word that you want to add.  
the corresponding  
number key.  
clear the symbol(s)  
insert the symbol(s)  
[
C
].  
2. Press [0] to display alternative words for your key  
presses. When there are no more alternative  
words, Add displays on the bottom line.  
<
OK>.  
3. Press <Add>.  
4. Enter the word you want using ABC mode and  
press <OK>.  
21  
X200.book Page 22 Friday, October 14, 2005 10:31 AM  
Redialling recent numbers  
1. In Idle mode, press [ ] to display the list of  
recent numbers.  
Call functions  
Advanced calling features  
2. Scroll to the number you want and press [ ].  
Making a call  
1. In Idle mode, enter the area code and phone  
number.  
Making a call from Phonebook  
Once you have stored a number in Phonebook, you  
can dial the number by selecting it from  
2. Press [ ].  
Phonebook.p. 50  
• Press [  
C] to clear the last digit or press and hold  
You can also use the speed dial feature to assign your  
most frequently called numbers to specific number  
[C] to clear the whole display. You can move the  
cursor to edit an incorrect digit.  
• Press and hold [ ] to enter a pause between  
numbers.  
keys.  
Dialling a number from the phone’s memory  
1. In Idle mode, press and hold [ ]. A + appears.  
p. 51  
0
Making an international call  
1. In Idle mode, press and hold [  
appears.  
2. Enter the location number for the phone number  
you want and press [ ].  
0]. The  
+
character  
3. Press [Up] or [Down] to scroll through other  
numbers.  
2. Enter the country code, area code, and phone  
number, then press [ ].  
4. Press <Dial> or [ ] to dial the number you want.  
22  
X200.book Page 23 Friday, October 14, 2005 10:31 AM  
Dialling a number from the SIM card  
When Active folder is active, you can simply open  
the phone. p. 57  
Press <Reject> or [ ] to reject a call.  
1. In Idle mode, enter the location number for the  
phone number you want and press [ ].  
2. Press [Up] or [Down] to scroll through other  
numbers.  
Viewing missed calls  
If you have missed calls, the screen displays how  
many calls you have missed.  
3. Press <Dial> or [ ] to dial the number you want.  
Ending a call  
1. Press <View>.  
Close the phone or press [ ].  
2. If necessary, scroll through the missed calls.  
3. Press [ ] to dial the number you want.  
Answering a call  
Using the headset  
Use the headset to make or answer calls without  
holding the phone.  
When you receive an incoming call, the phone rings  
and displays the incoming call image.  
Press <Accept> or [ ] to answer the call.  
Connect the headset to the jack on the left side of the  
phone.  
Tips for answering a call  
When Anykey answer is active, you can press  
any key to answer a call, except for <Reject> or  
[
].p. 57  
23  
X200.book Page 24 Friday, October 14, 2005 10:31 AM  
Call functions  
The button on the headset works as listed below:  
Making a second call  
You can make another call if your network supports it.  
1. Press <Hold> to put the call on hold.  
2. Make the second call in the normal way.  
3. Press <Swap> to switch between the calls.  
To  
Press  
redial the last call  
answer a call  
end a call  
the button twice.  
the button.  
the button.  
4. Press <Options> and select End held call to end  
the call on hold.  
5. To end the current call, press [ ].  
Options during a call  
You can access a number of functions during a call.  
Answering a second call  
You can answer an incoming call, if your network  
supports it and you have activated the call waiting  
Adjusting the volume during a call  
Use [ / ] to adjust the earpiece volume during a call.  
feature.  
p. 30  
Press [ ] to increase the volume level and [ ] to  
decrease the volume level.  
1. Press [ ] to answer the call. The first call is  
automatically put on hold.  
2. Press <Swap> to switch between the calls.  
Placing a call on hold/Retrieving  
Press <Hold> or <Unhold> to place the call on hold  
or retrieve the call.  
3. Press <Options> and select End held call to end  
the call on hold.  
4. To end the current call, press [ ].  
24  
X200.book Page 25 Friday, October 14, 2005 10:31 AM  
Using the Speakerphone feature  
Muting or sending key tones  
Use your phone as a speaker phone to talk and listen  
with the phone a short distance away.  
You can turn the key tones off or on.  
Press <Options> and select Mute keys or Send  
Press <Options> and select Speaker ON  
/Normal  
.
keys.  
To communicate with answering machines or  
computerised telephone systems, Send keys must  
be selected.  
Transferring a call  
You can transfer the currently active call to a caller on  
hold, if your network supports it. With this option, the  
two callers can talk to each other, but you are  
disconnected from the call.  
Sending a sequence of DTMF tones  
Dual tone multi-frequency (DTMF) tones are the tones  
used in phones for tone dialling.  
Press <Options> and select Transfer  
.
You can send DTMF tones as a group after entering the  
entire number you need to send or retrieving a  
number from Phonebook. This feature is helpful for  
entering a password or an account number when you  
call an automated system, like a banking service.  
Using the menu functions  
Press <Options> and select Menu  
.
Switching off the microphone  
You can temporarily switch off your phone’s  
microphone so that the other person on the phone  
cannot hear you.  
(Mute mode)  
1. When connected with a teleservice system, press  
<
Options> and select Send DTMF  
2. Enter the number you need to send and press  
OK>.  
.
Press <Options> and select Mute or Unmute  
.
<
25  
X200.book Page 26 Friday, October 14, 2005 10:31 AM  
Call functions  
Having a private conversation with one  
participant  
Using Phonebook  
You can access the Phonebook menu to locate or  
1. Press <Options> and select Select one  
2. Select a name or number from the participant list.  
3. Select Private  
.
store entries.p. 50  
Press <Options> and select Phonebook  
.
.
Making a multi-party call  
Use this feature to allow as many as six people to join  
a multi-party call, or conference call.  
You can talk privately with that person, while the  
other participants converse with each other.  
4. To return to the multi-party call, press <Options  
>
Your service provider must support multi-party calls  
for you to use this feature.  
and select Join  
.
Disconnecting one participant  
Setting up a multi-party call  
1. Call the first participant.  
1. Press <Options> and select Select one  
.
2. Select a name or number from the participant list.  
3. Select Remove  
2. Call the second participant. The first call is  
automatically put on hold.  
.
The participant is dropped from the call, but the  
call continues with the other parties.  
3. Press <Options> and select Join. The first  
participant is added to the multi-party call.  
4. Press [ ] to end the multi-party call.  
4. If desired, call another person or answer an  
incoming call.  
5. Press <Options> and select Join  
.
6. Repeat steps 4 and 5 as desired.  
26  
X200.book Page 27 Friday, October 14, 2005 10:31 AM  
Call records (Menu 2)  
Use this menu to view the calls you have dialled,  
received, or missed, the length of your calls, and the  
cost of your calls.  
Menu functions  
All menu options listed  
To access this menu, press <Menu> in Idle mode and  
SIM AT (Menu 1)  
select Call records  
.
This menu is available if you use a SIM AT card that  
provides additional services, such as news, weather,  
sports, entertainment, and location services. Available  
services may vary, depending on your service  
provider’s plans.  
Missed calls (Menu 2.1)  
This menu displays the most recently received calls  
that you did not answer.  
Accessing a call record  
1. Select a call record.  
For details, see your SIM card instructions or contact  
your service provider.  
2. Press [Up] or [Down] to move to another call  
record.  
To access this menu, press <Menu> in Idle mode and  
select SIM AT  
.
3. Press [ ] to dial or, <Options> to access call  
record options.  
27  
X200.book Page 28 Friday, October 14, 2005 10:31 AM  
Menu functions  
Using call record options  
Call time (Menu 2.5)  
While viewing call details, press <Options> to access  
the following options:  
This menu displays the time log for calls made and  
received. The actual time invoiced by your service  
provider will vary.  
Edit: change the number of the selected call  
record.  
Last call time: check the length of your last call.  
Delete: delete the selected call record.  
Total sent: check the total length of all the calls  
you have dialled.  
Received calls (Menu 2.2)  
Total received: check the total length of all the  
calls you have received.  
This menu displays the most recent calls you have  
received.  
Reset timers: reset the call timers. You need to  
enter the phone password.  
Dialled calls (Menu 2.3)  
The password is preset to 00000000. You can  
This menu displays the most recent calls you have  
dialled.  
change this password.p. 56  
Call cost (Menu 2.6)  
Delete all (Menu 2.4)  
This network feature displays the cost of calls. This  
menu is available only if your SIM card supports this  
feature. Note that this is not intended to be used for  
billing purposes.  
Use this menu to delete all of the records in each call  
type.  
1. Press [  
] to select the call types to be cleared.  
2. Press <Delete>.  
Last call cost: check the cost of your last call.  
3. Press <Yes> twice to confirm the deletion.  
28  
X200.book Page 29 Friday, October 14, 2005 10:31 AM  
Total cost: check the total cost of all of your calls.  
If the total cost exceeds the maximum cost set in  
Set max cost, you must reset the counter before  
you can make another call.  
Call diverting (Menu 3.1)  
This network service reroutes incoming calls to a  
phone number that you specify.  
1. Select a call diverting option:  
Max cost: check the maximum cost limit set in  
Divert always: divert all calls.  
Busy: divert calls when you are on another  
call.  
Set max cost  
.
Reset counters: reset the cost counters.  
Set max cost: set the maximum cost authorised  
for your calls.  
No reply: divert calls when you do not answer  
the phone.  
Unreachable: divert calls when you are not in  
an area covered by your service provider or  
when your phone is switched off.  
Cancel all: cancel all call diverting options.  
Price/Unit: set the price per unit that is applied  
when the cost of your calls is calculated.  
Network services (Menu 3)  
Use this menu to access network services. Please  
contact your service provider to check their availability  
and subscribe to them, if you wish.  
2. Select the type of calls to be diverted.  
3. To activate call diverting, press <Activate>.  
Otherwise, press <Options> and select Remove  
.
4. Enter the number to which calls are to be diverted  
To access this menu, press <Menu> in Idle mode and  
select Network services  
and press <OK>.  
.
29  
X200.book Page 30 Friday, October 14, 2005 10:31 AM  
Menu functions  
5. If you selected No reply, select the length of time  
the network delays before diverting a call and  
press <Select>.  
2. Select the type of calls to be barred.  
3. Press <Activate>. To deactivate call barring,  
press <Deactivate>.  
4. Enter the call barring password supplied by your  
Call barring (Menu 3.2)  
service provider and press <OK>.  
This network service allows you to restrict your calls.  
1. Select a call barring option:  
Call waiting (Menu 3.3)  
All outgoing: prohibit all outgoing calls.  
International: prohibit international calls.  
International except home: only allow calls  
to numbers within the current country when  
you are abroad, and to your home country.  
All incoming: prohibit incoming calls.  
Incoming while abroad: prohibit incoming  
calls when you use your phone outside of your  
home country.  
Cancel all: cancel all call barring settings,  
allowing calls to be sent and received normally.  
Change barring password: change the call  
barring password obtained from your service  
provider.  
This network service informs you when someone is  
trying to reach you while you are on another call.  
1. Select the type of calls to which the call waiting  
option will apply.  
2. Press <Activate>. To deactivate call waiting,  
press <Deactivate>.  
Network selection (Menu 3.4)  
This network service allows you to either automatically  
or manually select the network used when roaming  
outside of your home area.  
You can select a network other than your home  
network only if there is a valid roaming agreement  
between the two.  
30  
X200.book Page 31 Friday, October 14, 2005 10:31 AM  
Automatic: connect to the first available network  
when roaming.  
Index list: list, add, or delete CUG index  
numbers. Press <Options> to access the options  
for setting up an index list.  
Manual: select the network you want.  
Outside access: enable calls to numbers other  
than those in the Closed user group. This feature  
depends on the nature of your CUG subscription.  
Caller ID (Menu 3.5)  
This network service allows you to prevent your phone  
number from being displayed on the phone of the  
person being called. However, some networks do not  
allow the user to change this setting.  
Default group: enable the default CUG, if you  
have set one with your service provider. When  
making a call, you are given the option of using  
your default CUG, instead of selecting one from the  
list.  
Default: use the default setting provided by the  
network.  
Hide number: ensure your number does not  
display on the other person’s phone.  
Band selection (Menu 3.7)  
For the phone to make and receive phone calls, it  
must register with an available network. Your phone  
can handle any of the following types of networks:  
GSM 1900 and Combined GSM 900/1800.  
Send number: send your number each time you  
make a call.  
Closed user group (Menu 3.6)  
The country where you purchased your phone  
determines the default band that it uses. When you  
travel abroad, you must remember to change to an  
appropriate band.  
Use this menu to set incoming and outgoing calls to be  
restricted to a selected user group. For details about  
how to create a closed user group, contact your  
service provider.  
31  
X200.book Page 32 Friday, October 14, 2005 10:31 AM  
Menu functions  
Vibra+melody: the phone vibrates three times  
and then starts ringing.  
Sound settings (Menu 4)  
Use this menu to customise various sound settings.  
Keypad tone (Menu 4.4)  
To access this menu, press <Menu> in Idle mode and  
select Sound settings  
.
Use this menu to select the tone that the phone  
sounds when you press a key.  
Ring tone (Menu 4.1)  
You can adjust the keypad tone volume using [ / ]  
in Idle mode.  
Use this menu to select a ringtone for the call ringer.  
You can select one of the default ring melodies or  
downloaded sounds.  
Message tone (Menu 4.5)  
Use this menu to change the sound settings for  
incoming SMS messages, MMS messages, and CB  
messages individually.  
Ring volume (Menu 4.2)  
Use this menu to adjust the ringtone volume.  
SMS tone: specify how you are informed of new  
SMS messages.  
Alert type (Menu 4.3)  
Use this menu to specify how you are to be informed  
of incoming calls.  
SMS-CB tone: specify how you are informed of  
new cell broadcast (CB) messages.  
Light only: the service light flashes; the phone  
neither rings nor vibrates.  
MMS tone: specify how you are informed of new  
MMS messages.  
Melody: the phone rings using the selected  
ringtone.  
Repetition: set how often the phone informs you  
of new messages.  
Vibration: the phone vibrates but not rings.  
32  
X200.book Page 33 Friday, October 14, 2005 10:31 AM  
Connect tone: set the phone to beep when an  
outgoing call is connected to the system.  
Alert on call (Menu 4.6)  
Use this menu to select whether or not the phone  
informs you when you receive a new message or when  
the time for an alarm comes during a call.  
Messages (Menu 5)  
Folder tone (Menu 4.7)  
Use the Messages menu to send and receive short  
messages, and multimedia messages. You can also  
use push message, voicemail, and cell broadcast  
message features.  
Use this menu to select the tone that the phone  
sounds when you open or close the phone.  
Power on/off (Menu 4.8)  
To access this menu, press <Menu> in Idle mode and  
select Messages  
.
Use this menu to select the melody that the phone  
plays when it is switched on or off.  
Text messages (Menu 5.1)  
Extra tones (Menu 4.9)  
Short Message Service (SMS) allows you to send or  
receive text messages including simple pictures,  
melodies, and animated images.  
Use this menu to customise additional tones for the  
phone.  
Error tone: set the phone to beep when you make  
a mistake.  
Minute minder: set the phone to beep every  
minute during an outgoing call to keep you  
informed of the length of your call.  
33  
X200.book Page 34 Friday, October 14, 2005 10:31 AM  
Menu functions  
Inbox (Menu 5.1.1)  
Outbox (Menu 5.1.2)  
Use this menu to view received text messages.  
Use this menu to view sent or saved text messages.  
While viewing a message, press <Options> to access  
the following options:  
While viewing a message, press <Options> to access  
the following options:  
Delete: delete the message.  
Delete: delete the message.  
Send: forward the message to other people.  
Text reply: reply to the sender.  
Call back: call the sender.  
Send: forward the message to other people.  
Cut address: extract URLs, e-mail addresses, or  
phone numbers from the message.  
Move to phone: move the message from the SIM  
card to the phone’s memory.  
Cut address: extract URLs, e-mail addresses, or  
phone numbers from the message.  
Move to SIM: move the message from the  
phone’s memory to the SIM card.  
Move to phone: move the message from the SIM  
card to the phone’s memory.  
Select objects: save images or sounds from the  
message into your phone.  
Move to SIM: move the message from the  
phone’s memory to the SIM card.  
Select objects: save images or sounds from the  
message into your phone.  
34  
X200.book Page 35 Friday, October 14, 2005 10:31 AM  
Write new (Menu 5.1.3)  
Templates (Menu 5.1.4)  
Use this menu to create and send text messages.  
1. Enter your message.  
Use this menu to create SMS templates with the  
sentences you use frequently so that you can retrieve  
and insert them when composing an SMS message.  
The maximum number of characters allowed in  
a short message varies by service provider. If  
your message exceeds the maximum number of  
characters, the phone will split the message.  
While viewing the templates list, press <Options> to  
access the following options:  
Edit: edit the template.  
Send message: send the template as an SMS  
message.  
2. Press <Options> to access the following options:  
Add objects: add a sound, melody, picture, or  
animated image to the message.  
Delete: delete the template.  
Add templates: retrieve a text template.  
Add emoticon: retrieve an emoticon.  
Add phonebook: add a Phonebook entry.  
Add bookmark: add a web page’s address.  
Emoticon templates (Menu 5.1.5)  
Your phone provides preset emoticons so that you can  
use when writing a message. Use this menu to create  
or edit emoticons.  
3. Press <Options> and select Send only  
,
Save  
While viewing the emoticon list, press <Options> to  
access the following options:  
and send or Save only  
.
4. If you select Save and send or Save only, select  
Add: add a new emoticon.  
a memory location.  
Edit: edit the selected emoticon.  
Send: send a message using the emoticon.  
Delete: delete the emoticon.  
5. Enter a destination number.  
6. Press <OK> to send the message.  
35  
X200.book Page 36 Friday, October 14, 2005 10:31 AM  
Menu functions  
Delivery reports: set the network to inform you  
when your message has been delivered.  
Settings (Menu 5.1.6)  
Use this menu to customise the SMS settings.  
Bearer selection: select the GSM or GPRS  
preferred bearer type.  
The setting options available in this menu may vary  
depending on your service provider.  
Delete all (Menu 5.1.7)  
Setting x (where  
each group has its own submenu.  
x
is the setting group number):  
Use this menu to delete all of SMS messages in each  
message box.  
Service centre: store or changes the number of  
your message centre.  
1. Press [  
cleared.  
] to select the message boxes to be  
Default destination: store a default destination  
number.  
2. Press <Delete>.  
3. Press <Yes> twice to confirm the deletion.  
Default type: set the default message type.  
Default validity: set the length of time your  
messages are stored in the SMS server.  
Memory status (Menu 5.1.8)  
Use this menu to check the number of SMS messages  
you have stored and total number of SMS messages  
you can store in each memory type.  
Setting name: change the name of the setting  
group.  
Common setting: the following options are  
available:  
Reply path: allow the recipient to reply to you  
through your message centre.  
36  
X200.book Page 37 Friday, October 14, 2005 10:31 AM  
The Archive box saves network messages  
indefinitely. Press <Options> and select Save  
when a text notification appears. The message is  
saved in the Archive box.  
Voice mail (Menu 5.1.9)  
Use this menu to store the number of the voicemail  
server and access your voicemails.  
You must enter the voice server number before you  
can access your voicemails. Your service provider  
can give the voice server number.  
Receive: select to receive broadcast messages, or  
not.  
Channel list: specify the channels from which you  
receive broadcast messages.  
Connect to voice server: connect to the voice  
server to allow you to listen to your messages. You  
can also connect to the voicemail server by  
Language: select the preferred languages in  
which broadcast messages display.  
pressing and holding [1] in Idle mode.  
Please contact your service provider for details.  
Voice server number: change the voicemail  
server number.  
Multimedia messages (Menu 5.2)  
Broadcast (Menu 5.1.0)  
Multimedia Message Service (MMS) delivers messages  
containing a combination of text, picture, and sound,  
from phone to phone or from phone to e-mail.  
The Cell Broadcast service delivers short messages on  
various topics such as the weather or traffic.  
Use this menu to change the settings for the service  
and access broadcast messages.  
Inbox (Menu 5.2.1)  
This menu displays MMS messages that you have  
received. The following icons tell you the message  
status:  
Read: open received messages.  
The Volatile box saves network messages until  
the phone is switched off.  
37  
X200.book Page 38 Friday, October 14, 2005 10:31 AM  
Menu functions  
Unread notification  
Read notification  
Retrieving from the server  
Processing your request  
Failed to send  
Properties: access the message properties.  
When you select a notification, you can access  
Retrieve to retrieve the message from the MMS  
server.  
Outbox (Menu 5.2.2)  
Read  
This menu displays MMS messages that you have  
sent. The following icons tell you the message status:  
Unread  
Being sent  
Sent  
While viewing a message, press <Options> to access  
the following message options:  
Failed to send  
To be sent  
Delete: delete the message.  
Reply: reply to the sender.  
Callback: call the sender.  
While viewing a message, press <Options> to access  
the following options:  
Cut address: extract URLs, e-mail addresses, or  
phone numbers from the message.  
Delete: delete the message.  
Forward: forward the message to other people.  
Cut address: extract URLs, e-mail addresses, or  
phone numbers from the message.  
Save picture: save an image from the message  
into the Images folder.  
Send: send or resend the message.  
Edit message: edit the message.  
Save sound: save a sound from the message into  
the Sounds folder.  
Properties: access the message properties.  
38  
X200.book Page 39 Friday, October 14, 2005 10:31 AM  
Preview: view the message you created.  
Draft (Menu 5.2.3)  
The maximum size allowed for a message can  
differ, depending on your service provider.  
After creating a multimedia message, you can store it  
in this message box for sending later.  
You can view a message and use the options the same  
3. If you want to change the added items, highlight  
one and press <Options> to access the following  
options:  
as in Outbox  
.
Write new (Menu 5.2.4)  
Edit text  
text, picture, or sound.  
/Edit picture/Edit sound: edit the  
You can create and send an MMS message.  
1. Enter the message subject and press <OK>.  
Add page: add pages. Move to each page by  
pressing [Left] or [Right] on the message  
screen.  
2. Press <Options> and add message contents using  
one of the following options:  
Add text: add message text.  
Delete: delete the item from your message.  
Duration: set how long one page displays.  
After the specified time, the display  
automatically scrolls to the next page.  
Add picture: add a picture to the message.  
Add sound: add a sound clip to the message.  
Save: save the message in the Draft or  
Templates box.  
4. When you have finished, select Send from the  
Settings: change the message settings.  
Add destination: enter destination numbers  
or addresses.  
options.  
5. Select a destination type (To, Cc, Bcc).  
6. Select one of Phone number  
,
E-mail address, or  
Phonebook  
.
39  
X200.book Page 40 Friday, October 14, 2005 10:31 AM  
Menu functions  
7. Enter a phone number or an e-mail address, or  
1. Press [  
cleared.  
] to select the message boxes to be  
select a number from Phonebook and press <OK>.  
8. To add more destinations, select Add destination  
2. Press <Delete>.  
and repeat from step 6.  
3. Press <Yes> twice to confirm the deletion.  
9. To enter additional numbers or addresses to other  
Memory status (Menu 5.2.7)  
destination types, press < >and repeat from step  
5.  
Use this menu to view the amount of memory  
available for MMS messages and memory currently in  
use in each message box.  
10.When you have finished, select Send message  
.
Templates (Menu 5.2.5)  
Setup (Menu 5.2.8)  
Use this menu to store MMS messages you saved as  
templates so that you can use them to create new  
messages.  
You can customise the settings for sending and  
receiving MMS messages.  
Delivery report: set the network to inform you  
when your message has been delivered.  
While viewing a message template, press <OK> to  
access the following options:  
Read reply: request a reply from the recipient.  
Edit message: send the message using the  
template.  
Auto download: set whether or not your phone  
retrieves new incoming messages from the MMS  
server without notifications.  
Delete: delete the template.  
Delete all (Menu 5.2.6)  
Message acceptance: select the category of  
messages you want to receive.  
Use this menu to delete all of MMS messages in each  
message box.  
40  
X200.book Page 41 Friday, October 14, 2005 10:31 AM  
Hide ID: hide your phone number on the  
recipient’s phone.  
Connection URL: enter the address of your MMS  
server.  
Expiry date: set the length of time your messages  
are stored in the message centre.  
Security: select a data transmission mode.  
IP address: enter the gateway address.  
User name: enter the user ID.  
Delivery time: set the time delay before  
messages are sent.  
Password: enter the password.  
Priority: set the priority level of your messages.  
APN: enter the access point name used for the  
address of the MMS server.  
Report allowed: send a delivery report from the  
network to the sender.  
Push messages (Menu 5.3)  
Page duration: set how long one page in your  
outgoing messages displays. After a specified time,  
the display automatically scrolls to the next page.  
Use this menu to access messages from the web  
server.  
Inbox: view push messages you have received.  
MMS profile (Menu 5.2.9)  
Receive: determine whether or not your phone  
receives push messages.  
You can configure required network settings for MMS.  
The last profile accessed is automatically activated for  
sending or receiving subsequent messages.  
Never: the phone rejects push messages.  
Always: the phone receives all push messages.  
Delete all: delete all push messages.  
Check with your service provider before you change  
any MMS settings on your phone.  
Profile name: assign a name to the MMS profile.  
41  
X200.book Page 42 Friday, October 14, 2005 10:31 AM  
Menu functions  
Navigating with the web browser  
Funbox (Menu 6)  
To  
Press  
[Up] or [Down].  
The Funbox menu allows you to use the web browser,  
play Java games, and access images and sounds  
stored in the phone’s memory.  
scroll through browser items  
select a browser item  
return to the previous page  
[
[
].  
To access this menu, press <Menu> in Idle mode and  
select Funbox  
.
C].  
WAP browser (Menu 6.1)  
Using page options  
The Wireless Application Protocol (WAP) browser on  
your phone allows you to access the wireless web.  
From any web page, press and hold [ ] to access the  
following options:  
From the wireless web, you can access up-to-date  
information and a wide variety of media content, such  
as games, wallpapers, and ringtones.  
Reload: reload the current page with updated  
information.  
Home: return to the homepage.  
Home (Menu 6.1.1)  
Go to URL: enter a URL address manually.  
Use this menu to connect your phone to the network  
and load the homepage of the wireless web service  
Show URL: view the URL address of the current  
web page.  
provider. You can also press [  
] in Idle mode.  
Edit home: change the page to be used for your  
homepage.  
Clear cache: delete information stored in the  
cache.  
42  
X200.book Page 43 Friday, October 14, 2005 10:31 AM  
Inbox: read messages received from a web  
server.  
Edit: edit the URL address and title of the  
bookmark.  
Delete: delete the bookmark.  
Exiting the web browser  
Press [ ] to exit the browser.  
http:// (Menu 6.1.3)  
Use this menu to manually enter a URL address and  
access the associated web page.  
Favorite (Menu 6.1.2)  
Use this menu to save URL addresses in order to  
quickly access web pages.  
Settings (Menu 6.1.4)  
Adding a bookmark  
Use this menu to set up servers for the web browser.  
Contact your service provider for details about your  
settings options.  
1. Select an empty location.  
2. Enter a URL address and press <Enter>.  
3. Enter a title for the bookmark and press <Enter>.  
Accessing a bookmarked page  
For each server, the following options are available:  
Profile name: assign a name to the server profile.  
Homepage URL: set the address of your  
homepage.  
Selecting a bookmark item launches the web browser  
and accesses the associated web page.  
Security: select a data transmission mode.  
Using bookmark options  
Bearer: select a bearer for each type of network  
After saving an item, press <Options> to access the  
following options:  
address accessed; GPRS or Data  
When the bearer is set to GPRS  
IP address: enter the web gateway address.  
.
:
Go to URL: access the website.  
43  
X200.book Page 44 Friday, October 14, 2005 10:31 AM  
Menu functions  
User name: enter the user ID.  
Games (Menu 6.2)  
Password: enter the password.  
You can download Java applications from various  
sources using the web browser, and store them in your  
phone.  
APN: enter the access point name of the GPRS  
network gateway.  
Java services may not available, depending on your  
service provider.  
When the bearer is set to Data  
:
IP address: enter the web gateway address.  
Login name: enter the user ID.  
Launching a game  
1. Select the game you want on the Games list.  
Password: enter the password.  
Dial-up number: enter the PPP server phone  
number.  
2. On the startup screen of the game, you can access  
the following options:  
Data call type: select a data call type.  
START GAME: start a new game.  
CONTINUE: continue the last game you  
played.  
HIGH SCORE: view the high score table. This  
option may not be available for some games.  
HOW TO PLAY: view how to play the game  
and the key functions for the game.  
OPTION: switch on or off the game sound.  
Clear cache (Menu 6.1.5)  
Use this menu to clear the cache, which is the  
temporary memory that stores the web pages you  
have recently accessed.  
3. Press [  
] to confirm your selection.  
44  
X200.book Page 45 Friday, October 14, 2005 10:31 AM  
Viewing game information  
Images (Menu 6.4)  
Scroll to the game you want and press <Info>.  
This menu displays images downloaded from the  
wireless web or received in messages.  
Changing the DNS settings  
While accessing an image, press <Options> to access  
the following options:  
You may need to change the DNS setting of the Java  
server at your service provider’s instructions.  
Rename: change the image name.  
1. Select Setting on the Games list.  
Delete: delete the image.  
2. Enter the primary DNS address and press <OK>.  
3. Enter the secondary DNS address and press  
Set as wallpaper: set the image as your  
wallpaper for the idle screen.  
<OK>.  
Delete all (Menu 6.5)  
Sounds (Menu 6.3)  
Use this menu to delete all of the downloaded items in  
This menu displays sounds downloaded from the  
wireless web or received in messages.  
the Games  
,
Sounds, and Images folders.  
1. Press [  
] to select the folders to be cleared.  
While accessing a sound, press <Options> to access  
the following options:  
2. Press <Delete>.  
3. Press <Yes> twice to confirm the deletion.  
Rename: change the sound name.  
Delete: delete the sound.  
Memory status (Menu 6.6)  
Set as ring tone: set the sound as your ringtone.  
Use this menu to check the total amount of memory  
for media items and the amount of memory currently  
in use in each media box.  
45  
X200.book Page 46 Friday, October 14, 2005 10:31 AM  
Menu functions  
Stopping an alarm  
Organiser (Menu 7)  
When the alarm sounds, press any key.  
The Organiser feature enables you to keep track of  
your schedule and tasks, and to record voice memos.  
You can also set the time and date and use convenient  
features, such as an alarm clock, a calculator, and a  
currency converter.  
To remove an alarm set, access it, press  
<Options> and select Remove alarm.  
To remove all alarm sets, select Remove alarm  
from the Alarm screen.  
To access this menu, press <Menu> in Idle mode and  
Setting the alarm to ring even if the phone is  
off  
select Organiser  
.
From the Alarm screen, select Autopower  
Enable.  
Alarm (Menu 7.1)  
If the phone is off when it is time for the alarm to ring,  
the phone switches on and sounds the alarm.  
Use this menu to set alarms to ring at a specific time.  
Setting an alarm  
1. Select the type of alarm.  
Calendar (Menu 7.2)  
Use this menu to consult the calendar, write memos,  
or set alarms to act as a reminder.  
2. Enter the time for the alarm to sound and press  
[
].  
3. Select AM or PM in 12-hour time format.  
Writing a memo  
4. If you selected Morning call in step 1, choose  
1. Select a date on the calendar.  
Monday to friday or Monday to saturday  
.
2. Enter your memo and press <OK>.  
46  
X200.book Page 47 Friday, October 14, 2005 10:31 AM  
3. Press [  
day.  
] to set an alarm to ring on the chosen  
While viewing a memo, press <Options> to access  
the following options:  
Otherwise, press <Skip>.  
4. Enter the time for the alarm and press [  
New: add a new memo.  
].  
Edit: edit the memo.  
To select an alarm melody, press <Melody>.  
Alarm: set an alarm for the memo.  
Delete: delete the memo.  
5. Select AM or PM in 12-hour format.  
The colour of the date on the calendar changes to  
pink to indicate that a memo exists for that date.  
Copy to: copy the memo to another date.  
Move to: change the date of the memo.  
Viewing a memo  
1. Select a date which has memos from the calendar.  
Time & Date (Menu 7.3)  
Use this menu to change the time and date displayed  
on your phone. Before setting the time and date,  
specify your time zone in World time  
2. Press [Up] or [Down] to view other memos  
scheduled for that day.  
.
Using calendar memo options  
Set time: enter the current time.  
On the calendar screen, press <Options> to access  
the following options:  
Set date: enter the current date.  
World time: set your local time zone and find out  
what time it is in another part of the world.  
Search all: view all of the memos you created.  
Delete all: delete all memos.  
Time format: select 12-hour or 24-hour time  
format.  
Go to date: go to a specific date.  
Exit: exit the Calendar menu.  
47  
X200.book Page 48 Friday, October 14, 2005 10:31 AM  
Menu functions  
4. Enter your deadline and press [  
].  
Calculator (Menu 7.4)  
Use this menu to perform basic arithmetic functions  
such as addition, subtraction, multiplication, and  
division.  
Viewing the task  
When you select the To do list menu, the tasks display  
with a check mark, if the task has been done, and a  
priority level indicator;  
and for Low.  
To change the status of a specific task, press [  
1. Enter the first number.  
for High,  
for Normal,  
Press <.()> to insert a decimal point or a  
bracket.  
]
.
Press  
[
] or [ ] to move the cursor.  
2. Press the Navigation keys to access the math  
function you want.  
While viewing a task or the task list, press <Options  
to access the following options:  
>
3. Enter the second number.  
New: add a new task.  
4. Press [  
] to view the result.  
Mark: change the status of the task.  
Edit: edit the task.  
5. If necessary, repeat from step 2 to continue the  
calculation.  
Sort: sort the task by priority or status.  
Copy: copy the task.  
To do list (Menu 7.5)  
Copy to calendar: copy the task to the calendar  
as a memo.  
Use this menu to create tasks and manage them.  
Creating a task  
1. Press <New>.  
Delete: delete the task.  
Delete all: delete all tasks.  
Exit: exit the To do list menu.  
2. Enter the first task and press <OK>.  
3. Select a priority level.  
48  
X200.book Page 49 Friday, October 14, 2005 10:31 AM  
Press <Options> to access the following options:  
Voice memo (Menu 7.6)  
Play: play back your voice memo.  
Use this menu to record voice memos. A voice memo  
can be up to 30 seconds.  
Send: send the voice memo via MMS.  
Rename: change the name of the voice memo.  
Voice record (Menu 7.6.1)  
1. Press <Record> to start recording.  
2. Speak into the microphone.  
Properties: access the properties of the voice  
memo.  
Delete: delete the voice memo.  
3. When you press <Stop>, or if the recording time  
expires, the following options display:  
Delete all (Menu 7.6.3)  
Replay: play back your memo.  
Re-record: discard the memo and record  
another one.  
Save: save the memo.  
Quit: cancel your recording and exit the Voice  
memo menu.  
Use this menu to delete all of the voice memos you  
have recorded at one time.  
Memory status (Menu 7.6.4)  
You can check the total amount of memory and the  
amount of memory currently in use for voice memos.  
4. Select Save to save the voice memo.  
Currency exchange (Menu 7.7)  
5. Enter a name of the voice memo and press <OK>.  
Use this menu to do currency conversions.  
Memo list (Menu 7.6.2)  
1. Enter the rate of foreign currency and press  
<OK>.  
Use this menu to access the list of voice memos you  
have recorded.  
49  
X200.book Page 50 Friday, October 14, 2005 10:31 AM  
Menu functions  
2. Enter the amount of the source currency you want  
3. Scroll to a number and press [ ] to dial, or press  
Options> to access Phonebook options.  
to convert and press <OK>.  
<
The amount you entered and its equivalent value  
in the foreign currency display.  
Using Phonebook options  
While viewing an entry, press <Options> to access  
the following options:  
Paste: paste the number into the normal dialling  
mode.  
Phonebook (Menu 8)  
You can store phone numbers on your SIM card and in  
your phone’s memory. The SIM card and phone’s  
memory are physically separate, but they are used as  
a single entity called Phonebook.  
Edit: edit entry information.  
Delete: delete the number.  
Copy: copy the number to the phone’s memory or  
SIM card.  
To access this menu, press <Menu> in Idle mode and  
select Phonebook, or press <Phonebook>.  
Caller group: assign a caller group.  
Add entry: add a new entry.  
Search (Menu 8.1)  
Send via IrDA: send the entry via infrared port.  
Use this menu to search for numbers in Phonebook.  
New entry (Menu 8.2)  
Finding an entry  
1. Enter the first few letters of the name that you  
want to find.  
Use this menu to add a new entry to Phonebook.  
Storing an entry in the phone’s memory  
1. Select a number type.  
2. Select an entry from the Phonebook list.  
50  
X200.book Page 51 Friday, October 14, 2005 10:31 AM  
2. Select Phone  
.
3. Select the name you want.  
3. Enter a name and press <OK>.  
4. Press [ ] to dial the number or <Options> to  
access Phonebook options.  
4. Enter a number or an e-mail address and press  
<
Save>.  
Edit group (Menu 8.4)  
5. Change the location number, if you want, and  
Use this menu to edit your caller groups’ properties.  
press <OK>.  
From the group list, press <Options> to access the  
following options:  
Storing an entry on the SIM card  
1. Select a number type.  
Call ring tone: set a ringtone for incoming calls  
from the group.  
2. Select SIM  
.
3. Enter a name and press <OK>.  
SMS tone: set a ringtone for incoming messages  
from the group.  
4. Enter a number and press <Save  
>
5. Change the location number, if you want, and  
Graphic: set a graphic icon for incoming calls from  
the group.  
press <OK>.  
Group name: assign a name to the group.  
Group search (Menu 8.3)  
Use this menu to search your entries in Phonebook in  
caller groups.  
Speed dial (Menu 8.5)  
Use this menu to assign speed dial numbers (2 to 9) to  
eight of your most frequently called numbers.  
1. Enter the first few letters of the group name.  
2. Select a group and press <View>.  
51  
X200.book Page 52 Friday, October 14, 2005 10:31 AM  
Menu functions  
Assigning speed dial entries  
Delete all (Menu 8.6)  
1. Select a key location from  
for your voicemail server.  
2
to  
9. Key  
1
is reserved  
Use this menu to delete all of the entries from  
Phonebook.  
2. Select an entry from the Phonebook list.  
1. Press [  
] to select the locations to be cleared.  
3. Select a number, if the entry has more than one  
number.  
2. Press <Delete>.  
3. Enter the phone password and press <OK>.  
4. Press <Yes> twice to confirm the deletion.  
Managing speed dial entries  
While viewing the Speed dial screen, press  
Memory status (Menu 8.7)  
<
Options> to access the following options:  
Change: assign a different number to a key.  
Delete: delete the speed dial setting for a key.  
Use this menu to check the total number of entries  
you can store and the number of the entries you have  
stored in the phone’s memory or on the SIM card.  
Delete all: delete the speed dial settings for all  
keys.  
SDN (Menu 8.8)  
Number: check the name and number assigned to  
This menu is available if your SIM card supports  
Service Dialling Numbers (SDN). Use this menu to  
view the list of SDNs assigned by your service  
provider, including emergency numbers, directory  
enquiries, and voicemail numbers.  
a key.  
Dialling speed dial entries  
Press and hold the appropriate key in Idle mode.  
Scroll to the number you want and press <Dial> or  
[
].  
52  
X200.book Page 53 Friday, October 14, 2005 10:31 AM  
align the IrDA port on the phone with the IrDA port  
on your phone computer or another phone.  
Phone settings (Menu 9)  
Use this menu to customise your phone settings. You  
can also reset the settings to their default values.  
To access this menu, press <Menu> in Idle mode and  
select Phone settings  
.
Infrared activate (Menu 9.1)  
Use this menu to send or receive data to or from IrDA-  
compatible computers or phones through the infrared  
port.  
The connection is ready for data transmission.  
If there is no communication between your phone and  
the IrDA-compliant device within 30 seconds  
With PC (Menu 9.1.1)  
activating the feature, it is automatically deactivated.  
Use this menu to use the infrared feature with a  
computer.  
With other phone (Menu 9.1.2)  
To use an infrared connection, you must:  
Use this menu to send or receive Phonebook entries  
from another compliant phone.  
configure and activate an IrDA-compliant infrared  
port on your PC.  
activate the infrared feature on the phone; the  
IrDA icon ( ) appears on the top line of the  
display.  
53  
X200.book Page 54 Friday, October 14, 2005 10:31 AM  
Menu functions  
Receiving data from another phone  
Sending your Phonebook  
1. Align the IrDA ports on both phones with each  
other.  
You can send Phonebook entries via IrDA connection.  
Display settings (Menu 9.2)  
2. When the list of the received data displays, select  
one of the two options:  
Use this menu to change settings for the display and  
light.  
To save an individual item:  
1. Select the item you want from the list.  
Wallpaper (Menu 9.2.1)  
2. Press <Options> and select Save to save the  
You can change the background image and the  
settings for the text of Idle mode.  
data.  
Otherwise, select Discard to delete the data.  
Wallpaper list: select a background image.  
To save all data:  
Text display: determine the phone displays the  
time and date.  
1. From the item list, press <Options> to select  
one of the following options:  
Text colour: select a text colour.  
Save all vCard: save all Phonebook entries.  
Discard all vCard: delete all Phonebook  
entries.  
Brightness (Menu 9.2.2)  
You can adjust the brightness of the display for  
varying lighting conditions.  
2. When FDN (Fixed Dialling Number) mode is  
enabled on your phone, enter the PIN2 and  
press <OK>.  
Contrast (Menu 9.2.3)  
You can adjust the contrast of the display for varying  
lighting conditions.  
3. Press <Save> to save the entries.  
54  
X200.book Page 55 Friday, October 14, 2005 10:31 AM  
Backlight (Menu 9.2.4)  
Greeting message (Menu 9.3)  
You can select the length of time the backlight and the  
display stay on.  
Use this menu to enter the greeting that is displayed  
briefly when the phone is switched on.  
Backlight on: select the length of time the  
backlight stays on.  
Own number (Menu 9.4)  
Use this feature to check your phone numbers, or to  
assign a name to each of the numbers. Changes made  
here do not affect the actual subscriber numbers on  
your SIM card.  
Backlight dim: select the length of time the  
display is in Dimming mode after the backlight  
turns off. After a specified time, the display turns  
off.  
Language (Menu 9.5)  
Service light (Menu 9.2.5)  
Use this menu to select one of several languages for  
the display text.  
The service LED on the front of the phone indicates  
when service is available on the phone. Use this menu  
to set whether or not the service light is used.  
Security (Menu 9.6)  
Use this menu to protect the phone against  
unauthorised use by managing the several access  
codes of your phone and SIM card.  
Graphic logo (Menu 9.2.6)  
Use this menu to display your service provider’s logo  
instead of its name.  
If you enter an incorrect PIN/PIN2 three times in  
succession, the SIM card is blocked. To unblock it  
you need to enter your PUK/PUK2 (Personal  
Unblocking Key). The codes are supplied by your  
network operator.  
Dialling font colour (Menu 9.2.7)  
Use this menu to select a font colour for the numbers  
entered while dialling.  
55  
X200.book Page 56 Friday, October 14, 2005 10:31 AM  
Menu functions  
PIN check (Menu 9.6.1)  
Privacy (Menu 9.6.5)  
The 4-to 8-digit PIN (Personal Identification Number)  
protects your SIM card against unauthorised use.  
When this feature is enabled, the phone requires your  
PIN each time it is switched on.  
Use this menu to lock your media contents, including  
MMS messages, voice memos, images, and sounds.  
1. Press [  
] to select the items to be locked.  
2. Press <OK> to lock the marked items.  
Change PIN (Menu 9.6.2)  
3. Enter the phone password and press <OK>.  
Use this menu to change your PIN. The PIN check  
feature must be enabled to use this feature.  
To access a locked item, you need to enter the phone  
password.  
Phone lock (Menu 9.6.3)  
SIM lock (Menu 9.6.6)  
The Phone lock feature locks the phone from  
unauthorised use.  
The SIM lock feature allows your phone to work only  
with the current SIM by assigning a SIM lock code. You  
must enter the SIM lock code to use a different SIM  
card.  
When this feature is enabled, you must enter a 4- to  
8-digit phone password each time the phone is  
switched on.  
FDN mode (Menu 9.6.7)  
The password is preset to 00000000. To change the  
password, use the Change password menu.  
If supported by your SIM card, Fixed Dialling Number  
(FDN) mode restricts your outgoing calls to a limited  
set of phone numbers. When this feature is enabled,  
you can make calls only to phone numbers stored on  
the SIM card.  
Change password (Menu 9.6.4)  
Use this menu to change your phone password.  
56  
X200.book Page 57 Friday, October 14, 2005 10:31 AM  
2. Select a menu to be assigned to the key.  
Change PIN2 (Menu 9.6.8)  
If supported by your SIM card, the Change PIN2  
feature changes your current PIN2.  
Reset settings (Menu 9.9)  
Use this menu to reset the phone’s settings you have  
changed.  
Extra settings (Menu 9.7)  
You can turn the automatic redialling or answering  
feature on or off.  
Enter the 4- to 8-digit phone password and press  
<
OK>.  
The password is preset to 00000000. You can  
change this password. p. 56  
Auto redial: set the phone to make up to ten  
attempts to redial a phone number after an  
unsuccessful call.  
Active folder: answer an incoming call by opening  
the phone.  
Anykey answer: answer an incoming call by  
pressing any key, except <Reject> or [ ].  
Short cut (Menu 9.8)  
You can use the Navigation keys as shortcut keys to  
access specific menus directly from Idle mode. Use  
this menu to change the shortcut assignments for the  
keys.  
1. Select a key to be used as a shortcut key.  
57  
X200.book Page 58 Friday, October 14, 2005 10:31 AM  
Solve problems  
“Enter PUK”  
The PIN code has been entered incorrectly three  
Solve problems  
Help and personal needs  
times in succession, and the phone is now blocked.  
Enter the PUK supplied by your service provider.  
To save the time and expense of an unnecessary service  
call, perform the simple checks in this section before  
contacting a service professional.  
“No service,” “Network failure,” or “Not  
done” displays  
The network connection has been lost. You may be  
in a weak signal area. Move and try again.  
When you switch on your phone, the  
following messages may appear:  
You are trying to access an option for which you  
have no subscription with your service provider.  
Contact the service provider for further details.  
“Insert SIM card”  
Be sure that the SIM card is correctly installed.  
“Phone locked Enter password”  
You have entered a number but it was not  
dialled  
The automatic locking function has been enabled.  
You must enter the phone’s password before you  
can use the phone.  
Be sure that you have pressed [ ].  
Be sure you have accessed the right cellular  
network.  
“Enter PIN”  
You are using your phone for the first time. You  
must enter the PIN supplied with the SIM card.  
Be sure that you have not set an outgoing call  
barring option.  
The PIN check feature is enabled. Every time the  
phone is switched on, the PIN has to be entered.  
To disable this feature, use the PIN check menu.  
58  
X200.book Page 59 Friday, October 14, 2005 10:31 AM  
Try moving the phone slightly or moving closer to a  
window if you are in a building.  
Your correspondent cannot reach you  
Be sure your phone is switched on. ([ ] pressed  
for more than one second.)  
No number is dialled when you re-call a  
Phonebook entry  
Be sure you are accessing the correct cellular  
network.  
Use the Search menu to ensure the number has  
been stored correctly.  
Be sure that you have not set an outgoing call  
barring option.  
Re-store the number, if necessary.  
Your correspondent cannot hear you speaking  
The battery doesn’t charge properly or the  
phone sometimes turns itself off  
Be sure you have switched off the microphone.  
Be sure you are holding the phone close enough to  
your mouth. The microphone is located at the  
bottom of the phone.  
Wipe the charging contacts both on the phone and  
on the battery with a clean soft cloth.  
If the above guidelines do not help you to  
solve the problem, take note of:  
The phone starts beeping and “Warning Low  
battery” flashes on the display  
The model and serial numbers of your phone  
Your warranty details  
Your battery is insufficiently charged. Recharge the  
battery.  
A clear description of the problem  
The audio quality of the call is poor  
Check the signal strength indicator on the display  
). The number of bars indicates the signal  
strength from strong ( ) to weak ( ).  
Then contact your local dealer or Samsung after-sales  
service.  
(
59  
X200.book Page 60 Friday, October 14, 2005 10:31 AM  
Health and safety information  
SAR tests are conducted using standard operating  
positions with the phone transmitting at its highest  
certified power level in all tested frequency bands.  
Although the SAR is determined at the highest certified  
power level, the actual SAR level of the phone while  
operating can be well below the maximum value. This is  
because the phone is designed to operate at multiple  
power levels so as to use only the power required to reach  
the network. In general, the closer you are to a base  
station, the lower the power output of the phone.  
Health and safety information  
SAR certification information  
This phone meets European Union (EU) requirements  
concerning exposure to radio waves.  
Your mobile phone is a radio transmitter and receiver. It is  
designed and manufactured to not exceed the limits for  
exposure to radio-frequency (RF) energy, as  
recommended by the EU Council. These limits are part of  
comprehensive guidelines and establish permitted levels  
of RF energy for the general population. The guidelines  
were developed by independent scientific organisations  
through the periodic and thorough evaluation of scientific  
studies. The limits include a substantial safety margin  
designed to ensure the safety of all persons, regardless of  
age and health.  
Before a new model phone is available for sale to the  
public, compliance with the European R&TTE Directive  
must be shown. This directive includes as one of its  
essential requirements the protection of the health and  
safety of the user and any other person.  
The exposure standard for mobile phones employs a unit  
of measurement known as Specific Absorption Rate (SAR).  
The SAR limit recommended by the EU Council is 2.0W/  
* The SAR limit for mobile phones used by the public is 2.0 watts/  
kilogram (W/kg) averaged over ten grams of body tissue. The  
limit incorporates a substantial margin of safety to give addi-  
tional protection for the public and to account for any variations  
in measurements. The SAR values may vary, depending on  
national reporting requirements and the network band.  
*
kg.  
The highest SAR value for this model phone was 0.74W/kg.  
60  
X200.book Page 61 Friday, October 14, 2005 10:31 AM  
Extreme temperatures will affect the charging capacity  
of your battery: it may require cooling or warming  
first.  
Do not leave the battery in hot or cold places because  
the capacity and lifetime of the battery will be  
reduced. Try to keep the battery at room temperature.  
A phone with a hot or cold battery may not work  
temporarily, even when the battery is fully charged. Li-  
ion batteries are particularly affected by temperatures  
below 0°C (32°F).  
Do not short-circuit the battery. Accidental short-  
circuiting can occur when a metallic object like a coin,  
clip or pen causes a direct connection between the +  
and – terminals of the battery (metal strips on the  
battery). For example, do not carry a spare battery in  
a pocket or bag where the battery may contact metal  
objects. Short-circuiting the terminals may damage  
the battery or the object causing the short-circuiting.  
Precautions when using batteries  
Never use a charger or battery that is damaged in any  
way.  
Use the battery only for its intended purpose.  
If you use the phone near the network’s base station,  
it uses less power. Talk and standby time are greatly  
affected by the signal strength on the cellular network  
and the parameters set by the network operator.  
Battery charging time depends on the remaining  
battery charge, the type of battery, and the charger  
used. The battery can be charged and discharged  
hundreds of times, but it will gradually wear out. When  
the operation time is noticeably shorter than normal, it  
is time to buy a new battery.  
If left unused, a fully charged battery will discharge  
itself over time.  
Use only Samsung-approved batteries, and recharge  
your battery only with Samsung-approved chargers.  
Disconnect the charger from the power source when it  
is not in use. Do not leave the battery connected to a  
charger for more than a week, since overcharging may  
shorten its life.  
Dispose of used batteries in accordance with local  
regulations. Always recycle. Do not dispose of  
batteries in a fire.  
61  
X200.book Page 62 Friday, October 14, 2005 10:31 AM  
Health and safety information  
Road safety  
Electronic devices  
Your wireless phone gives you the powerful ability to  
communicate by voice, almost anywhere, anytime. But an  
important responsibility accompanies the benefits of  
wireless phones, one that every user must uphold.  
Most modern electronic equipment is shielded from radio  
frequency (RF) signals. However, certain electronic  
equipment may not be shielded against the RF signals  
from your wireless phone. Consult the manufacturer to  
discuss alternatives.  
When driving a car, driving is your first responsibility.  
When using your wireless phone while driving, follow local  
regulations in the country or region you are in.  
Pacemakers  
Pacemaker manufacturers recommend that a minimum  
distance of 15 cm (6 inches) be maintained between a  
wireless phone and a pacemaker to avoid potential  
interference with the pacemaker. These recommendations  
are consistent with the independent research and  
recommendations of Wireless Technology Research. If you  
have any reason to suspect that interference is taking  
place, switch off your phone immediately.  
Operating environment  
Remember to follow any special regulations in force in the  
area you are in, and always switch off your phone  
whenever it is forbidden to use it, or when it may cause  
interference or danger.  
When connecting the phone or any accessory to another  
device, read its user’s guide for detailed safety  
instructions. Do not connect incompatible products.  
Hearing aids  
Some digital wireless phones may interfere with some  
hearing aids. In the event of such interference, you may  
wish to consult your hearing aid manufacturer to discuss  
alternatives.  
As with other mobile radio transmitting equipment, users  
are advised that for the satisfactory operation of the  
equipment and for the safety of personnel, it is  
recommended that the equipment should only be used in  
the normal operating position (held to your ear with the  
antenna pointing over your shoulder).  
62  
X200.book Page 63 Friday, October 14, 2005 10:31 AM  
Other medical devices  
Potentially explosive environments  
If you use any other personal medical devices, consult the  
manufacturer of your device to determine if it is  
adequately shielded from external RF energy.  
Switch off your phone when in any area with a potentially  
explosive atmosphere, and obey all signs and instructions.  
Sparks in such areas could cause an explosion or fire  
resulting in bodily injury or even death.  
Your physician may be able to assist you in obtaining this  
information.  
Users are advised to switch off the phone while at a  
refuelling point (service station). Users are reminded of  
the need to observe restrictions on the use of radio  
equipment in fuel depots (fuel storage and distribution  
areas), chemical plants, or where blasting operations are  
in progress.  
Switch off your phone in health care facilities when  
regulations posted in these areas instruct you to do so.  
Vehicles  
RF signals may affect improperly installed or inadequately  
shielded electronic systems in motor vehicles. Check with  
the manufacturer or its representative regarding your  
vehicle.  
Areas with a potentially explosive atmosphere are often  
but not always clearly marked. They include the areas  
below decks on boats, chemical transfer or storage  
facilities, vehicles using liquefied petroleum gas, such as  
propane or butane, areas where the air contains chemicals  
or particles, such as grain, dust or metal powders, and any  
other area where you would normally be advised to turn  
off your vehicle engine.  
You should also consult the manufacturer of any  
equipment that has been added to your vehicle.  
Posted facilities  
Switch off your phone in any facility where posted notices  
require you to do so.  
63  
X200.book Page 64 Friday, October 14, 2005 10:31 AM  
Health and safety information  
Emergency calls  
Other important safety information  
Only qualified personnel should service the phone or  
install the phone in a vehicle. Faulty installation or  
service may be dangerous and may invalidate any  
warranty applicable to the device.  
Check regularly that all wireless phone equipment in  
your vehicle is mounted and operating properly.  
Do not store or carry flammable liquids, gases, or  
explosive materials in the same compartment as the  
phone, its parts, or accessories.  
For vehicles equipped with an air bag, remember that  
an air bag inflates with great force. Do not place  
objects, including installed or portable wireless  
equipment, in the area over the air bag or in the air  
bag deployment area. Improperly installed wireless  
equipment could result in serious injury if the air bag  
inflates.  
Switch off your phone before boarding an aircraft. It is  
dangerous and illegal to use wireless phones in an  
aircraft because they can interfere with the operation  
of the aircraft.  
Failure to observe these instructions may lead to the  
suspension or denial of telephone services to the  
offender, or legal action, or both.  
This phone, like any wireless phone, operates using radio  
signals, wireless, and landline networks as well as user-  
programmed functions, which cannot guarantee  
connection in all conditions. Therefore, you should never  
rely solely on any wireless phone for essential  
communications like medical emergencies.  
To make or receive calls, the phone must be switched on  
and in a service area with adequate signal strength.  
Emergency calls may not be possible on all wireless phone  
networks or when certain network services and/or phone  
features are in use. Check with local service providers.  
To make an emergency call:  
1. Switch on the phone.  
2. Key in the emergency number for your present  
location. Emergency numbers vary by location.  
3. Press [ ].  
Certain features like Call Barring may need to be  
deactivated before you can make an emergency call.  
Consult this document and your local cellular service  
provider.  
64  
X200.book Page 65 Friday, October 14, 2005 10:31 AM  
Do not store the phone in cold areas. When the phone  
warms up to its normal operating temperature,  
moisture can form inside the phone, which may  
damage the phone’s electronic circuit boards.  
Do not drop, knock, or shake the phone. Rough  
handling can break internal circuit boards.  
Do not use harsh chemicals, cleaning solvents, or  
strong detergents to clean the phone. Wipe it with a  
soft cloth slightly dampened in a mild soap-and-water  
solution.  
Do not paint the phone. Paint can clog the device’s  
moving parts and prevent proper operation.  
Do not put the phone in or on heating devices, such as  
a microwave oven, stove, or radiator. The phone may  
explode when overheated.  
When the phone or battery gets wet, the label  
indicating water damage inside the phone changes  
colour. In this case, phone repairs are no longer  
guaranteed by the manufacturer's warranty, even if  
the warranty for your phone has not expired.  
Care and maintenance  
Your phone is a product of superior design and  
craftsmanship and should be treated with care. The  
suggestions below will help you fulfill any warranty  
obligations and allow you to enjoy this product for many  
years.  
Keep your phone and all its parts and accessories out  
of the reach of small children and pets. They may  
inadvertently damage these things or choke on small  
parts.  
Keep the phone dry. Precipitation, humidity, and  
liquids contain minerals that corrode electronic  
circuits.  
Do not use the phone with a wet hand. Doing so may  
cause an electric shock to you or damage to the  
phone.  
Do not use or store the phone in dusty, dirty areas, as  
its moving parts may be damaged.  
Do not store the phone in hot areas. High  
temperatures can shorten the life of electronic  
devices, damage batteries, and warp or melt certain  
plastics.  
If your phone has a flash or light, do not use it too  
close to the eyes of people or animals. This may cause  
damage to their eyes.  
65  
X200.book Page 66 Friday, October 14, 2005 10:31 AM  
Health and safety information  
Use only the supplied or an approved replacement  
antenna. Unauthorised antennas or modified  
accessories may damage the phone and violate  
regulations governing radio devices.  
If the phone, battery, charger, or any accessory is not  
working properly, take it to your nearest qualified  
service facility. The personnel there will assist you, and  
if necessary, arrange for service.  
66  
X200.book Page 67 Friday, October 14, 2005 10:31 AM  
Index  
Call cost • 28  
Call records  
A
D
F
ABC mode, text input • 19  
Active folder • 57  
Alarm • 46  
Date, set • 47  
Deleting  
FDN (Fixed Dialling Number)  
mode • 56  
dialled • 28  
missed • 27  
received • 28  
call records • 27  
Folder tone • 33  
Funbox • 42  
Answering  
MMS • 38, 40  
phonebook • 52  
SMS • 34, 40  
Call time • 28  
Caller ID • 31  
Calls  
call • 23  
G
second call • 24  
Anykey answer • 57  
Auto redial • 57  
Games • 44  
Delivery reports, message • 40  
Dialled calls • 28  
Dialling font, set • 55  
Display  
Greeting message • 55  
answering • 23  
barring • 30  
holding • 24  
redialling • 22  
rejecting • 23  
transferring • 25  
waiting • 30  
H
B
Health and safety • 60  
Holding, call • 24  
Background image • 54  
Backlight time, set • 55  
Band selection • 31  
Barring, calls • 30  
Battery  
backlight, set • 55  
brightness • 54  
contrast • 54  
icons • 10  
language • 55  
layout • 10  
service light, set • 55  
settings • 54  
I
Icons, description • 10  
Images, downloaded • 45  
Inbox, messages  
MMS • 37  
CB(CellBroadcast)messages•  
37  
Characters, enter • 19  
Connection tone • 33  
Converter • 49  
Creating messages  
MMS • 39  
charging • 7  
low indicator • 8  
precautions • 61  
Broadcast messages • 37  
Browser, web • 42  
SMS • 34  
Infrared port • 53  
International calls • 22  
Internet • 42  
Diverting calls • 29  
DTMF tones, send • 25  
C
E
SMS • 35  
CUG (Closed User Group) • 31  
Calculator • 48  
Calendar • 46  
J
Emergency calls • 64  
Java applications • 44  
67  
X200.book Page 68 Friday, October 14, 2005 10:31 AM  
Index  
Minute minder • 33  
Missed calls • 27  
MMS messages  
65  
display • 10  
icons • 10  
locking • 13, 56  
password • 56  
resetting • 57  
switching on/off • 8  
unpacking • 6  
Resetting phone • 57  
Ringer  
incoming calls • 32  
messages • 32  
Road safety • 62  
Roaming • 30  
K
Keypad tones  
selecting • 32  
sending/muting • 25  
volume • 32  
creating/sending • 39  
deleting • 38  
setting • 40  
L
viewing • 37  
S
Language, select • 55  
Last number, redial • 22  
Locking  
Multiparty-calls • 26  
Safety  
Phonebook  
N
Names  
information • 60  
SDN (Service Dialling  
Numbers) • 52  
Security, calls • 55  
Sent messages  
MMS • 37, 38  
SMS • 34  
Service light • 55  
Shortcut • 13, 57  
Silent mode • 13  
SIM card  
inserting • 7  
locking • 56  
SMS messages  
creating/sending • 35  
deleting • 36  
setting • 36  
adding • 50  
deleting • 52  
finding • 50  
options • 50  
speed dialling • 51  
menu functions • 56  
phone • 56  
SIM card • 56  
entering • 19  
searching • 50  
Network band, selection • 30  
Network services • 29  
Low battery indicator • 8  
PIN, change • 56  
M
PIN2, change • 57  
Power on/off tone • 33  
Privacy • 56  
Problems, solve • 58  
Push messages • 41  
O
Memory status  
downloaded items • 45  
messages • 40  
phonebook • 52  
Message tone • 32  
Messages  
Organiser • 46  
Outbox, messages  
MMS • 38  
SMS • 34  
R
P
cell broadcast • 37  
greeting • 55  
MMS • 37  
push • 41  
SMS • 33  
Received calls • 28  
Recording, voice memos • 49  
Redialling  
Password  
call barring • 30  
phone • 56  
Phone  
automatically • 57  
manually • 22  
viewing • 34  
care and maintenance •  
voice • 37  
68  
X200.book Page 69 Friday, October 14, 2005 10:31 AM  
Sound settings • 32  
Sounds, downloaded • 45  
Speakerphone • 25  
Speed dial • 51  
Switching on/off  
microphone • 25  
phone • 8  
T
T9 mode, text input • 20  
Templates  
MMS • 39  
SMS • 35  
Text, enter • 19  
Time, set • 47  
V
Voice memos • 49  
Voicemail server • 37  
W
Waiting call • 30  
Wallpaper • 54  
Web browser  
access • 42  
bookmarks • 43  
World time • 46  
69  

Sony J30SDI User Manual
Sony Cell Phone CMD Z28 User Manual
Sonic Alert SBS550BC User Manual
Samsung SGH a877 Series User Manual
Samsung SCH R330 Series User Manual
Samsung DLP TV SP42L6HX User Manual
Panasonic CQ VX999EW User Manual
Panasonic CQ RX400U User Manual
Oki 70037301 User Manual
Nokia 6680 User Manual