eSATA II 2-Port ExpressCard
Quick Installation Guide
IntroducingtheeSATAII2-PortExpressCard
The eSATA II 2-Port ExpressCard is an ultra high-speed
dual channel Serial ATA Generation 2 controller.
FeaturesandBenefits
•
Ad d s tw o external (eSATA) p orts to you r
ExpressCard equipped notebook computer for
external drive connections
•
•
Supports data transfer speeds up to 3.0Gb/ s
(300MB/ s)
Supports Native Command Queuing (NCQ) and
SATA TCQ commands
•
•
Compliant with Serial ATA 1.0a specification
Compliant with eSATA (external SATA) connector
specifications
•
•
Supports SATA hard disk hot-plugging
Breaks the 137GB barrier! Works with various
brands of large capacity Serial ATA hard disks
SystemRequirements
•
•
•
PC or Mac notebook with an available ExpressCard
slot
Windows® 2000 / XP (32-/ 64-bit) / Server 2003 &
2008 (32-/ 64-bit) / Vista (32-/ 64-bit)
Mac OS® X v10.4.9 - v10.5.6
1
04-0487A
Windows Driver Installation
This section provides instructions to install the eSATA II
2-Port ExpressCard drivers.
Windows2000
1. Install the ExpressCard into an ExpressCard slot.
2. At the Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommended) and click Next.
4. Insertthedriver CD,checkCD-ROM drives,uncheck
the other boxes, and click Next. Click Next again.
5. Click Finish then restart Windows to complete the
driver installation.
Windows XP / Server 2003 (32-bit)
1. Install the ExpressCard into an ExpressCard slot.
2. At the Found New Hardware Wizard:
XP (w/SP1 or earlier) / Server 2003: continue to step #3
XP (w/SP2 or later) / Server 2003 (w/ SP1 or later):
select No, not this time, then click Next.
3. Insert the driver CD, select Install the software
automatically (Recommended), click Next, then
click Next again.
4. Click Finish, then restart Windows to complete the
driver installation.
Windows XP / Server 2003 (64-bit)
1. Install the ExpressCard into an ExpressCard slot.
2. At the Found New Hardware Wizard,select No,not
this time, then click Next
3
3. Insert the driver CD, select Install the software
automatically (Recommended), click Next, then
click Next again.
4. Click Finish then restart Windows to complete the
driver installation.
WindowsVistaTM (32-/64-bit)
1. Install the ExpressCard into an ExpressCard slot.
2. At the Found New Hardware window, click Locate
and install driver software (recommended), click
Continue.
3. At the next window, insert the driver CD andVista
will automatically detect and install the correct
driver.
4. At the successfull installed window, click Close
then restart Windows to complete the driver
installation.
WindowsServer2008(32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware window,select Locate
and install driver software (Recommended), then
click Don't Search Online.
3. Insert the driver CD and Windows will search the
CD and install the correct driver.
4. At Windows has finished installing the driver
software for this device, click Close to complete the
installation.
ToVerifyWindowsInstallation
1. Use Device Manager to verify proper installation.
For Windows 2000 / XP / Server 2003: Right click My
Computer, click Manage, click Device Manager.
4
For Windows Vista: Right click Computer, click
Manage, click Continue. Click Device Manager.
For Windows Server 2008: Right click Computer and
click Manage. Double click Diagnostics, click
Device Manager.
2. Double click either SCSI and RAID controllers or
Storage controllers, and Silicon Image SiI 3132...
Controller should be displayed.
Windows Device Connection
ExternalDevices
External Serial ATA devices should come with their own
accessories. In most cases, you just need to power up the
external device and connect it to the external port. For
more information, please refer to the external device's
manual.
ConnectingHardDiskDrives
When connecting a hard disk drive, hold the eSATA II
2-Port ExpressCard so it does not move from side to side,
otherwise, the ExpressCard may eject from the slot.
Hot-PluggingHardDiskDrives
Follow these instructions to remove a hard drive from a
powered up system, not following these instructions
may corrupt or destroy data or cause system crashes.
1. Right click My Computer and click Manage. (For
Windows Vista operating system, click Continue).
2. Select Device Manager.
3. Double click Disk Drives, right click the hard disk
and select Disable. (Select Enable for a previously
disabled hard drive)
5
4. You can now unplug the hard disk.
Note: When reconnecting a Disabled hard disk, it
must be enabled, otherwise, it will not work
properly in Windows. To enable the hard disk,
follow steps 1-3. At step #3, select Enable.
Assigning a Drive Letter in Windows
Windows may not assign a drive letter to a hard drive
enclosurethat waspartitioned and formatted in a different
computer. If this happens when you connect your
enclosure, follow the directions below to assign it a drive
letter. The steps, written from Windows Server 2003, are
similar in all Windows versions.
1. Right click My Computer, click Manage, click Disk
Management. In this window look for a Healthy
disk without a name and drive letter assigned to it,
See Figure 2 below.
Figure 2
6
2. Right click on the Healthy disk, that does not have
a drive letter, then click on Change Drive Letter and
Paths. See Figure 3 below.
Figure 3
3. At Change Drive Letters and Paths box, click Add.
Figure 4
7
4. At Add Drive Letter or Path box, select Assign the
following drive letter, choose an available drive
letter from the drop down box, then click OK.
Figure 5
5. A drive letter should be assigned to the Healthy
drive. Repeat these steps if no drive letter appears.
Figure 6
8
Safely Remove Hardware (Windows only)
Use Windows Safely Remove Hardware utility to stop
the ExpressCard before removing it from the ExpressCard
slot. Not doing so may corrupt or destroy your data.
Windows 2000 / XP / Server 2003 & 2008
1.
The utility is in the taskbar by the system clock.
For Windows 2000: Click the Unplug or Eject
Hardware icon.
For Windows XP / Server 2003 & 2008: Click the
Safely Remove Hardware icon.
2. Click Safely Remove Silicon Image SiI 3132
SATALink Controller.
3. Wait for the Safe to Remove Hardware pop-up box
to appear before removing the ExpressCard from
the ExpressCard slot.
WindowsVista
The eSATA II ExpressCard will appear in the Safely
Remove Hardware utility only if it is plugged into the
computer before booting up Windows.
1. Click the Safely Remove Hardware icon.
2. Click Safely Remove Silicon Image SiI 3132
SATALink Controller.
3. At the Safe To Remove Hardware box, click OK. It
is now safe to remove the ExpressCard.
Note: If the ExpressCard does not appear in the
Safely Remove Hardware utility, the connected
hard drive(s)must first be disabled before removing
the ExpressCard from the slot. Not doing so may
corrupt or destroy your data. See Hot Plugging
Hard Disk Drives on page 5 for more information.
9
Mac OS Driver Installation
This section provides information on how to install the
eSATA II 2-Port ExpressCard drivers.
1. Insert driver CD. At the desktop double click Driver
icon.
2. Double click Mac folder.
3. Double click Sil3132_1.1.9u_Si1_Pkg.pkg.
4. Click Continue, Continue, Continue, then Agree.
5.
In OS 10.5,click Change Install Location.Otherwise,
please continue with step #6.
6. Select the destination drive, click Continue, then
click Install.
7. At Authenticate, if there's a password enter it now,
then OK. Otherwise, just click OK.
8. At the successful install screen, click Close.
9. Restart Mac OS to complete the installation. When
Mac OS resumes, insert the expresscard at any time.
To Verify Mac Installation
1.
At the Desktop, click Go, then click Utilities.
2. Double click System Profiler.
3. Under Hardware, click PCI Cards.
4. On the right side of the screen, ExpressCard and
Subsystem ID:0x3132,along with other data should
be displayed.
Mac OS Hot-swapping Hard Disk Drives
1. Click and drag the drive icon into the Trashcan.
2. You can now safely unplug the hard disk drive.
10
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
to your questions could be just a few clicks away. You can also submit
questions online and a technical support analysts will promptly
respond.
SIIG offersa lifetimemanufacturer warranty with thisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyour purchase has passed the store's return policy period,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. Ifthe product is determined to be defective,
an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
11
About SIIG, Inc.
Founded in 1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
ofI/ O connectivity products,including PCI&ISA serialand parallel
ports,USB,SerialATA &UltraATA controllers,FireWire (1394a/ b),
networking, sound cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIG productsoffer comprehensiveuser manuals,many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK,and through e-commerce sites.
PRODUCT NAME
eSATA II 2-Port ExpressCard
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
eSATA II 2-Port ExpressCard is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarksofSIIG,Inc. Microsoft,Windowsand WindowsVista areeither registered trademarksor
trademarks of Microsoft Corporation in the United States and/ or other countries. Mac and Mac OS
areregistered trademarksofApple,Inc. Othernamesused in thispublication areforidentification only
and may betrademarksoftheir respectivecompanies.
June, 2009
Copyright © 2009 by SIIG, Inc. All rights reserved.
|