SL7810/65 Coffee Machine
4222.200.0290.1_DFU.indd
1
3/26/09 11:03:48 AM
3
14. Do not use this appliance at altitudes higher than 6800 ft./
2200m above sea level.
15. Flush the Coffee Machine with fresh water before using it for
the first time (See ‘Preparing the machine for use’).This will
cause the boiler to fill with water; which is essential for the
machine to work properly.
16.To prevent scalds and/or property damage, always make sure
Coffee Machine lid is securely in place and properly locked
before you start using the machine and during brew cycle. Do
not force when opening or closing lid.
17. Do not open lid until Coffee Machine has finished brew cycle.
Hot steam or hot water trapped under lid cover could burn
your fingers.
18.Warning:To reduce the risk of fire or electric shock,
do not remove the bottom cover. No user serviceable
parts are inside. For assistance call 1-866-473-6736
SAVETHESE
INSTRUCTIONS
SPECIAL INSTRUCTIONS
This Coffee Machine has a short cord to reduce the hazards of
becoming entangled in or tripping over a longer cord.An extension
cord may be used if the rating is equal to or greater than the rating
of the Coffee Machine. Use an extension cord rated 13 amperes
or greater. Care must be taken to arrange extension cord so that it
does not hang over the edge of counter top or table top, where it
can be pulled on by children or tripped over unintentionally.
Operating the Coffee Machine and another appliance at the same
time from the same electrical circuit could cause an electrical
overload, which would blow the fuse or trip the circuit breaker.
SPECIAL POLARIZED PLUG
INSTRUCTIONS
This Senseo Coffee Machine has a polarized plug (one blade is
wider than the other) as an added safety feature.To reduce the risk
of electric shock:
- Plug will fit into polarized outlet only one way.
- If plug does not properly fit into outlet at first, reverse it.
- If plug still does not fit, contact a qualified electrician.
DO NOT ATTEMPTTO DEFEATTHIS
SAFETY FEATURE IN ANYWAY.
4222.200.0290.1_DFU.indd
3
3/26/09 11:03:49 AM
4
WARNING:
-To avoid risk of personal injury or damage to property as a result
of overflow, be sure that the cup or mug is centered under the
coffee outflow unit during the brew cycle.
- Brewed coffee and coffee pods are very hot. Handle with care to
avoid scalding.
- If coffee outflow unit overflows or fails to drain into cup/mug
during brewing cycle, do not open lid or handle coffee outflow
unit or coffee pod holder(s). Unplug Coffee Machine and wait for
contents to cool before handling.
- Do not remove any part of Coffee Machine or cup/mug during
the brew cycle as scalding could occur.
- Use only fresh, cool water in this appliance. Do not put any other
liquids in this appliance except as instructed in the ‘Descaling’
section. Do not refill the water reservoir with hot water or
coffee.
- DO NOT attempt to move an appliance containing hot liquids or
during the brewing process. Allow appliance to cool completely
before moving.
- Keep appliance at least 4 inches away from walls or other objects
while operating. Do not place any object on top of coffee
machine while operating.
PLEASE READ AND SAVETHIS
INSTRUCTION BOOKLET.
4222.200.0290.1_DFU.indd
4
3/26/09 11:03:49 AM
5
TABLE OF CONTENTS
Features
6
Introduction
Preparing the machine for use
Brewing coffee
Cleaning
7
8
10
12
13
14
15
15
17
Descaling
Storage
Assistance
Trouble shooting guide
Warranty
To fully benefit from the support that Senseo
4222.200.0290.1_DFU.indd
5
3/26/09 11:03:49 AM
6
Features
A
Water reservoir
BReservoir splash guard
C1-pod holder; for 1 small cup of coffee (125 ml/app. 4.0 oz)
D2-pod holder, for 2 small cups of coffee (125 ml/app. 4.0 oz each)
or 1 mug of coffee (250 ml/app. 8.0 oz)
ECoffee outflow unit
FCover of coffee outflow unit
GDrip tray
HCup tray
IMetal distribution disk
JSealing ring
KOutflow valve
LIndicator light
4222.200.0290.1_DFU.indd
6
3/26/09 11:03:49 AM
7
Introduction
With the Senseo® coffee machine by Senseo you can enjoy a perfect
cup of coffee - topped with a rich frothy coffee layer - whenever
you feel like it. Each cup is freshly brewed, so you're always sure of
that pure, smooth taste.The patented Senseo brewing system in
combination with the special Senseo coffee pods makes sure you get
only the very best in flavor and aroma from freshly roasted coffee.
To optimize the taste of the coffee, you should keep the following
aspects in mind:
Fresh water
Use fresh water every day. Before using for the first time or if you
have not used the machine for some time, rinse the water reservoir,
fill it with fresh water and flush the machine before you begin brewing
coffee (see ‘Preparing the machine for use’).
Senseo coffee pods
In order to avoid damage, use only Senseo coffee pods that have been
specifically developed for your Senseo coffee machine for a pure,
smooth taste.The Senseo coffee pods will stay fresh longer if you close
the package by means of the keep-fresh seal after use or if you store
them in a storage container.
A clean machine
Scale build-up may cause overheating of the heating element and may
make the safety cut-out operate prematurely, switching off before the
water boils. Scale may also reduce the working life of the machine and
may lengthen the brewing time.
Clean and descale your Senseo coffee machine regularly (see 'Cleaning'
and 'Descaling'). Remove used coffee pods after brewing. If a used
pod has been left in the coffee machine and you have not used the
machine for some time, flush the machine before you use it again (see
'Preparing the machine for use').
4222.200.0290.1_DFU.indd
7
3/26/09 11:03:50 AM
8
Preparing the machine for use
◗ Use this Senseo coffee machine for its intended household use as
described in this manual.
YOU CANNOT BREW COFFEE IFYOU HAVE NOT
FLUSHEDTHE SENSEO COFFEE MACHINE FIRST!
The flushing cycle causes the boiler to be filled with water.After this
the coffee machine is ready for use.
Flush the machine in the following way:
1
2
3
Remove the water reservoir.
C
C
C
Fill the water reservoir with cold water up to the MAX
indication and put it back into the machine.
Release the lid by moving the lever upwards.
4
5
Open the lid.
C
C
Put either the 1- or 2-pod holder in the machine without using
any coffee pod(s).
4222.200.0290.1_DFU.indd
8
3/26/09 11:03:51 AM
9
6
Close the lid and lock the lever.
Make sure the lever is properly locked by pushing it down until it snaps
home with a click.
Never flush the machine with the lid open!The lid must be properly
locked.
C
C
C
B
B
7
Put the plug into a 120V AC electrical outlet.
8
Put a bowl (with a capacity of at least 1.5 liters/1.6 qt.) under
the coffee outflow unit to collect the water.
9
Press on/off button I.Then press both the ° and °°
buttons briefly at the same time.
◗ The machine will fill itself with water from the water reservoir.
This will take some time and you will probably not notice that
this is happening. After a while, the machine will start flushing and
it will switch itself off after the flushing cycle. During the flushing
cycle the machine produces more noise than during a regular
brewing cycle.
B
Before brewing coffee for the first time, clean the coffee outflow unit and
the pod holders with hot water and some dish soap or in a dishwasher.
Clean the water reservoir thoroughly in hot water, if necessary with some
dish soap.
◗ Now your Senseo coffee machine is ready for use!
Brewing coffee
1
Fill the water reservoir with cold water up to the MAX
indication and put it back into the machine.
C
Never pour milk, coffee, hot water or carbonated water into the water
reservoir.
- ° MIN: minimum amount of water required to brew one 4.0 oz.
cup of Senseo coffee.
- °° MIN: minimum amount of water required to brew one 8.0 oz.
mug or two 4.0 oz. cups of Senseo coffee.
- HD7810:A full reservoir allows you to make up to five 4.0 oz. cups
Senseo coffee.
4222.200.0290.1_DFU.indd
9
3/26/09 11:03:53 AM
10
2
Press on/off button I.
C
C
The indicator light blinks while the water is heating up. Heating up takes
approx. 90 seconds.
◗ The coffee machine is ready for use when the indicator light is lit
continuously.
3
4
Release the lid by moving the lever upwards.
Open the lid.
5
First place the appropriate coffee pod holder in the machine.
Make sure the coffee pod holder is clean and the sieve in the center is
not clogged (i.e. with loose coffee grounds).
B
◗ If you want to make one 4.0 oz. cup of Senseo coffee, use the 1-
C
C
pod holder.
◗ If you want to make one 8.0 oz. mug or two 4.0 oz. cups of
Senseo coffee, use 2 coffee pods in combination with the deeper
2-pod holder and the °° button.
6
Place the Senseo coffee pod(s) properly in the center of the
pod holder, with the flat Senseo side up and the rounded side
facing down.
B
Use Senseo coffee pods that have been specifically developed for your
Senseo coffee machine for a pure and smooth taste.
◗ Place 1 Senseo coffee pod in the 1-pod holder or
C
4222.200.0290.1_DFU.indd 10
3/26/09 11:03:55 AM
11
◗ Place 2 Senseo coffee pods in the 2-pod holder.
C
C
C
C
B
Make sure the coffee in the pod(s) is evenly distributed and press the
pod(s) lightly into the pod holder.
Never use torn pods or normal ground coffee, as this could cause the
B
machine to become blocked.
7
Close the lid and lock the lever.
Always check if the lid is properly locked.The lever must be pushed
down until it snaps home with a click.
Never start brewing coffee with the lid open!The lid must be properly
closed.
8
Place one cup, two cups or one mug under the outflow
openings.
If you are using cups, make sure they have a capacity of app. 5.0 oz. If
you are using a mug, make sure the mug has a capacity of app. 10.0
oz. Do not use cups or mugs that are too large, as they will cause the
coffee to get cold more quickly. If using one cup or one mug, be sure
to position the cup or mug right under the coffee outflow unit with its
two openings
9
Press the button indicating the number of cups of Senseo
coffee you want to brew.
- ° for one 4.0 oz. cup
- °° for two 4.0 oz. cups or one 8.0 oz. mug
◗ The Senseo coffee machine starts brewing.
- The machine automatically supplies the optimal amount of water.
- You can interrupt the brewing process at any time by pressing the
on/off button I. If you switch the machine back on after having
interrupted the brewing process, the machine will NOT complete
the interrupted brewing cycle.
Do not remove the water reservoir during a brewing cycle, as this will
cause the machine to draw in air.When this happens, the next cup will
only be partly filled.
If the mug/cups is/are half full when the machine stops brewing, there
was not enough water left in the water reservoir to brew two cups or
one mug. Refill the water reservoir and press button ° to fill up the
two cups or mug.
4222.200.0290.1_DFU.indd 11
3/26/09 11:03:57 AM
12
10 Remove and discard the coffee pod(s) after use by lifting the
coffee pod holder out of the machine and emptying it. Coffee
pod(s) should not be used more than one time.
Be careful when doing this, for there may still be some hot water/coffee
on the coffee pod(s) or steam may escape. If the coffee pod sticks to
the metal distribution disk inside the lid, let the pod cool down first
before carefully removing it, making sure not to touch the hot metal
disk.
Tips
◗ By rinsing the coffee pod holders and the coffee outflow unit
regularly, you will make sure that the coffee always tastes best.
◗ Senseo coffee will taste best if you stir it before drinking it.
◗ If you intend to make another cup of Senseo coffee later, just leave
the coffee machine switched on.The machine will automatically
switch itself off after app. one hour.
C
Cleaning
Never immerse the Senseo coffee machine in water or any other
liquid.
Never clean the machine by flushing it with the lid open.
1
Always turn machine off and unplug the machine before
cleaning it.
2
3
Clean the outside of the machine with a moist cloth.
Remove the coffee outflow unit.
C
C
◗ You can disassemble the coffee outflow unit for more thorough
cleaning!
4
Clean the coffee outflow unit, the pod holders and the drip
tray in hot water, if necessary with some dish soap, or in the
dishwasher.
C
4222.200.0290.1_DFU.indd 12
3/26/09 11:03:58 AM
13
5
Hold the cup tray in your hand while cleaning it with hot water,
if necessary with some dish soap.
C
C
C
The cup tray can also be cleaned in the dishwasher.
To clean the cup tray, remove it from the machine, as it might prove
sharp when handled incorrectly.Always handle it carefully!
6
Clean the coffee pod holders in hot water, if necessary with
some dishwashing soap or in the dishwasher.
Check if the sieve in the center of the pod holders is clogged. If the
sieve is clogged, unclog it by holding the pod holder under a running
faucet. If necessary, you can use a soft brush to unclog the sieve.
7
Clean the water reservoir in hot water, if necessary with some
dish soap or in the dishwasher.
The splash guard on the water reservoir can be removed to allow
thorough cleaning of the inside.
If you are using a soft brush or mesh covered sponge, be careful not to
damage the valve in the bottom of the water reservoir.
B
B
8
Rinse the parts with fresh water after cleaning and put them
back into the machine.
9
Clean the metal distribution disk with a moist cloth.
C
C
Be careful when you do this; make sure that the rubber sealing ring
does not get stuck under the edge of the metal distribution disk. If it
does, the coffee machine will start leaking!
Descaling
Regular descaling will prolong the life of your Senseo coffee machine
and will guarantee optimal brewing results for a long time. If the
machine is used twice a day on average, it must be descaled once
every 3 months.
1
Fill the water reservoir up to the MAX indication with white
vinegar or with a mixture of descaler and water according to
the instructions on the package of the descaler.Then put the
water reservoir back into the coffee machine.
Use a citric acid based descaler.
4222.200.0290.1_DFU.indd 13
3/26/09 11:04:00 AM
14
2
Press on/off button I.
C
The machine is ready for use when the indicator light is lit continuously.
3
Place the 1-pod holder in the coffee machine, preferably with a
used coffee pod in it. Close the lid and make sure it is properly
locked.
We advise you to put a used coffee pod in the pod holder when you
descale the machine, as it will serve as a 'filter' to prevent the sieve in
the pod holder from getting clogged with scale residues.
4
Put a bowl with a capacity of at least 1.5 liters/1.6 qt. under
the coffee outflow unit to collect the vinegar or the mixture of
descaler and water.
C
C
5
Press button °° and let the machine operate. Repeat this
until the water reservoir is empty.
Never descale the Senseo coffee machine with the lid open. Make
sure the lid is properly locked.
6
Repeat steps 1 to 5 with new vinegar or a new mixture of
descaler and water.
7
Empty the water reservoir to remove the last vinegar or
mixture of descaler and water. Repeat step 1 to 5 with fresh
water only (i.s.o. vinegar or descaler) at least 3 times to fully
clean the machine. Discard hot water each time.
◗ Do not refill water reservoir with used hot water.
8
Discard the used coffee pod and clean the coffee pod holder
after descaling to prevent the sieve in the center from getting
clogged.
This coffee machine has no other user-serviceable parts.
For assistance call 1-866-473-6736.
Storage
◗ If the coffee machine has already been used and therefore has
been flushed with water, it may only be used and stored in a safe,
frost-free place to prevent it from becoming damaged.
◗ Empty water reservoir before storing.
4222.200.0290.1_DFU.indd 14
3/26/09 11:04:01 AM
15
Assistance
For assistance call toll free: 1-866-4SENSEO (1-866-473-6736) or visit
our website: www.senseo.com.
Information is available 24 hours a day, 7 days a week.
Troubleshooting guide
If you experience a problem with your Senseo coffee machine, you
may find the solution in the table below. If the table does not provide
the solution to your problem or if you have a question, see the chapter
'Assistance'.
Problem
Solution
The indicator light continues to blink slowly You need to flush the coffee machine. See 'Preparing the machine for use'.
You are using the Senseo coffee machine at an altitude higher than 2200 m/
6800 ft. above sea level.This has caused the water in the machine to start
boiling before it has reached the required temperature, which prevents the
machine from functioning properly. Switch the machine off and do not use
it at altitudes higher than 2200 m/6800 ft. above sea level.
The Senseo coffee machine does not
The coffee machine must be flushed with water before using it for the
produce coffee when used for the first time first time, so that the boiler will be completely filled with water. Flush
the coffee machine (see 'Preparing the machine for use') before you
start brewing coffee.
The indicator light continues to blink rapidly Make sure that the water reservoir has been properly placed;
Make sure that there is enough water in the water reservoir (water
level above the ° MIN level if you want to brew one 4.0 oz. cup and
above °° if you want to brew one 8.0 oz. mug or two 4.0 oz. cups);
Make sure that the ambient temperature is not lower than 10cC/50cF.
If it is lower, the appliance will not function properly.
Water leaks from the coffee machine
Make sure that the lid is properly closed (the lever must be properly locked);
Make sure that the water reservoir has not been filled beyond the MAX level;
Make sure that the sieve in the center of the coffee pod holder is not
clogged. If it is, unclog the sieve by holding the coffee pod holder under
a running tap. If necessary, you can use a soft brush, pin or a toothpick
to unclog the sieve;
Make sure the coffee pod(s) has/have been put properly in the center
of the coffee pod holder with the flat Senseo side up;
Make sure the sealing ring has not gotten stuck under the edge of
the metal distribution disk (see drawing at the beginning of these
instructions for use);
Make sure that the drip tray does not overflow. It is unlikely that it will
overflow, but it is easier to empty when half full than full.
It is perfectly normal for some drops of water to spill onto the counter.
This may happen, for instance, when you place or remove the water
reservoir. Be careful when removing used coffee pods, for there may still
be some water on the pods.
4222.200.0290.1_DFU.indd 15
3/26/09 11:04:01 AM
16
Problem
Solution
Do not remove the water reservoir when the coffee machine is
heating up, as this may cause some water to leak out of the machine
(this water would normally end up in the water reservoir).
In all other cases, call 1-866-473-6736 for assistance
The lid cannot be opened.
A vacuum may have temporarily formed under the lid.Turn the
machine off. Pull the lever up as far as it will go and wait 24 hours
before opening the lid.
Make sure that the sieve in the center of the coffee pod holder is not
clogged. If it is, unclog the sieve by holding the coffee pod holder under
a running faucet. If necessary, you can use a soft to unclog the sieve.
If problems continue to occur, call 1-866-473-6736 for assistance
The coffee machine produces less coffee than
before.
Perhaps the sieve in the centre of the pod holder is clogged. If this is
the case, unclog the sieve by rinsing the pod holder under a running
faucet. If necessary, you can use a soft brush to unclog the sieve.
Descale the machine (see 'Descaling').
The lid cannot be closed properly.
Check if a used coffee pod is sticking to the metal distribution disk. If
this is the case, remove the used pod. Make sure that the sealing ring is
lying flat.
The machine has been stored in a room that
was not frost-free.
Call 1-866-473-6736 for assistance
The Senseo coffee is not strong enough.
Make sure you have used the correct number of pods and pressed the
right button. Use 1 pod in combination with the 1-pod holder and the
° button. Use 2 pods in combination with the 2-pod holder and the
°° button;
Check if the coffee pod(s) has/have been placed properly in the center
of the pod holder, to prevent water from escaping along the edge of
the pod(s).When you are using two coffee pods on top of each other,
make sure that the flat Senseo sides of both pods are facing up and
rounded sides are facing down. Press the pods lightly into the pod
holder;
Make sure you have not used the same pod twice by accident. Do not
use a pod twice, as it will give the coffee a bad taste. Use a fresh pod
for every brew;
The coffee in the pod needs to be evenly distributed;
If you prefer a more robust flavor, Senseo coffee pods with a stronger
blend are available.
The Senseo coffee is too strong
If you prefer a milder flavor, Senseo coffee pods with a milder blend are
available.
The Senseo coffee is not hot enough
Do not use cups that are too large, as they will cause the coffee to get
cold more quickly.When using cups, make sure they have a capacity of
150 ml/app. 5.0 oz.When using a mug, make sure it has a capacity of
280 ml/10.0 oz.When using a mug, always use 2 pods in combination
with the 2-pod holder and the °° button.
4222.200.0290.1_DFU.indd 16
3/26/09 11:04:01 AM
17
LIMITEDWARRANTY
Sara Lee Corporation hereby warrants that if your Senseo Single Serve Gourmet Coffee Maker Model
SL7810 (except cord, coffee pods and accessories) is found to be defective in materials or workmanship
during the period one year from the date of purchase, Sara Lee Corporation will, at its option, either (1)
repair or replace any defective product without charge to you, or (2) refund your purchase price. This
warranty extends only to the original retail purchaser.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack of
reasonable care, the affixing of any attachment not provided with the product, loss of parts, or subjecting
the product to any but the specified voltage.1 Use of unauthorized replacement parts will also void this
warranty. Sara Lee Corporation will not pay for warranty service performed by a non-authorized repair
service.
In order to obtain warranty service, call our Consumer Affairs Hotline at 1-866-473-6736. You will need
proof of purchase to obtain a warranty remedy.
REPAIR, REPLACEMENT OR REFUND (ATTHE OPTION OF SARA LEE CORPORATION) ISYOUR
ONLY REMEDY UNDERTHE ABOVE WARRANTY. SARA LEE CORPORATION SHALL NOT BE
LIABLE FOR ANY OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS, EXPENSES OR
DAMAGES.
NO OTHER WARRANTY,WRITTEN OR ORAL, IS AUTHORIZED BY SARA LEE CORPORATION.
ALL IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITEDTO,THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITEDTOTHE DURA-
TION OFTHE APPLICABLE WRITTEN WARRANTY ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state.
1 Read the instructions enclosed with your SENSEO unit carefully.
Manufactured for:
Sara Lee
3500 Lacey Road
Downers Grove, IL 60515
SENSEO® is a registered trademark of Sara Lee/DE N.V. when used for coffee pods
©2009 Sara Lee Corporation
4222.200.0290.1_DFU.indd 17
3/26/09 11:04:01 AM
18
4222.200.0290.1_DFU.indd 18
3/26/09 11:04:01 AM
19
4222.200.0290.1_DFU.indd 19
3/26/09 11:04:01 AM
|