Nokia 2160i User Manual

OWNER’S

MANUAL

K e ys a n d th e D is p la y

Switches phone

on/off when you

press and hold.

Adjusts volume of the earphone

or handsfree speaker.

These keys perform

the function shown

on the display

directly above them

(e.g., here the keys

are the “Menu” and

“Memory” keys).

“Dials” the number

on display. With

display clear, redials

last number dialed.

Ends a call.

PRINTED IN CANADA

Public System the phone uses (A, B, or both).

None shown: Home area only.

A call is in progress.

Digital signaling is in use.

The phone is roaming in a home type

system. Flashing: roaming in a non-home

type system.

The phone is in alpha mode.

You have a voice message.

You have a text message. If

flashing, text memory is full.

Memory location, menu,

or option number.

Battery

Charge

Signal

Strength

These words change; they determine the function of the

display, the left

^{keys direct}ñ^{ly below them (e.g., with these words on}

key is the “Menu” key and the right

key is the “Memory” key).

C o n n e c t o r s

➊

➋

➌ ➍

1) For Rapid Cigarette Lighter Charger, Rapid Travel

Charger, and Standard Travel Charger

2) Power connector for Desktop Charger CHH-2/CHH-2L

3) System and data connector for accessories, desktop

chargers, and HF car kit

4) For external antenna

iii

Ta b le o f C o n te n t s

1. Sa fe t y At A G la n c e ............................ 1

2 . Th e B a t te r y ....................................... 3

3 . B a s ic s ............................................... 7

Switching On or Off..............................................7

Signal Strength ....................................................7

Access Codes .....................................................7

4 . M a k in g a n d Re c e iv in g C a lls ............. 9

Answering a Call ..................................................9

Making a Call .......................................................9

Speed Dialing.....................................................10

Last Number Redial ...........................................10

One-Touch Dialing .............................................10

Emergency Key 9...............................................11

Voice Mail Key 1 ................................................11

Earpiece Volume................................................11

Calling Line Identification....................................12

Special Ringing Tone .........................................12

Key Lock............................................................13

Call Waiting........................................................13

Calling Card Calls...............................................14

5 . Vo ic e a n d Te x t M e s s a g e s .............. 15

Voice Messages.................................................15

Message Mode..................................................16

Text Messages...................................................16

To Dial a Number in a Message .........................17

6 . Th e Pe r s o n a l D ir e c to r y .................. 19

Alpha Mode .......................................................19

Entering Names .................................................20

Storing Numbers and Names.............................21

Recalling Stored Numbers .................................22

Recalling Stored Names.....................................22

7 . Te m p o r a r y L is ts & C a ll Tim e r s .......2 4

To view Dialed Numbers ....................................24

To view Last Received Calls...............................24

To view Missed Calls..........................................24

Call Timers.........................................................25

8 . To u c h To n e s .................................. 2 6

Sending Individual Touch Tones........................ 26

Sending Strings of Touch Tones........................ 26

Touch Tone Settings in the Phone..................... 28

9 . Th e M e n u ....................................... 2 9

Summary of Menu Functions and Shortcuts...... 30

Menu 01, Memory Functions............................. 32

Menu 2, Messages............................................ 32

Menu 3, Call Settings ........................................ 32

Menu 4, Phone Settings.................................... 34

Menu 5, Security Options.................................. 37

Menu 6, Network Services ................................ 38

Menu 7, System Search .................................... 43

Menu 8, NAM Selection..................................... 43

Menu 9, Number Editor..................................... 44

Menu 10, Alert Options ..................................... 44

Menu 11, Lock the Keys.................................... 45

10 . D a ta a n d Fa x C a lls ....................... 4 6

11. Ac c e s s o r ie s .................................. 4 8

Batteries............................................................ 48

Chargers........................................................... 50

12 . C a r e a n d M a in te n a n c e ................. 5 3

13 . Fo r Yo u r Sa fe t y ............................ 5 4

Traffic Safety ..................................................... 54

Operating Environment...................................... 54

Emergency Calls ............................................... 55

14 . Te c h n ic a l D a t a ............................. 5 7

1. S a f e t y A t A G la n c e

Read these simple guidelines before using your

phone. Failure to comply with these guidelines

may be dangerous or illegal.

For more detailed safety information, see

“For Your Safety” on page 54.

Ro a d Sa fe t y C o m e s Fir s t

Don't use a hand-held phone while driving; park the

vehicle first.

Sw itc h O ff In H o s p it a ls

Switch off your phone when near medical equip-

ment. Follow any regulations or rules in force.

Sw itc h O ff O n Air c r a ft

Mobile phones can cause interference. Using them

on aircraft is illegal.

Sw itc h O ff W h e n Re fu e lin g

Do not use your phone at a refueling point. Do not

use near fuels or chemicals.

Sw itc h O ff N e a r B la s t in g

Do not use your phone where a blasting operation

is in progress. Observe restrictions, and follow any

regulations or rules in force.

Us e Se n s ib ly

Use only in the normal position (to ear). Avoid un-

necessary contact with the antenna when phone is

on.

In te r fe r e n c e

All mobile phones may be subject to radio interfer-

ence, which may affect the performance of your

phone. Therefore, you should never rely solely upon

any cellular phone for essential communications

(e.g., medical emergencies).

Q u a lifie d Se r v ic e

Only qualified service personnel may install or repair

cellular phone equipment. Use only approved ac-

cessories and batteries.

Us in g th is O w n e r ’s M a n u a l

The cellular phone described in this manual is approved for

use in AMPS/TDMA networks.

A number of features included in this guide are called

Network Services. They are special services provided by

cellular service providers. Before you can take advantage

of any of these Network Services, you must subscribe to

them through your home service provider. You can then

activate these functions as described in this manual.

The manual activation commands for various services are

not presented in this guide (e.g. ∗ and # characters for

activating or deactivating services). The phone nevertheless

is capable of handling commands given in that form. For

these commands please consult with your service

provider.

FC C /In d u s t r y C a n a d a N o t ic e

Your phone may cause TV or radio interference (e.g. when

using a telephone in close proximity to receiving equip-

ment). The FCC/Industry Canada can require you to stop

using your telephone if such interference cannot be elimi-

nated. If you require assistance, contact your local service

facility.

THIS DEVICE COMPLIES WITH PARTS 15 AND 68 OF

THE FCC RULES. OPERATION IS SUBJECT TO THE

CONDITION THAT THIS DEVICE DOES NOT CAUSE

HARMFUL INTERFERENCE.

2 . Th e B a t t e r y

Your phone is powered by a rechargeable battery. Use

only batteries approved by the phone manufacturer and

recharge your battery only with the chargers approved by

the manufacturer.

New batteries must be charged with

the phone off for at least 24 hours

before initial use. A new battery’s

full performance is achieved only

after two or three complete charge

and discharge cycles!

Note: This chapter gives only the basics for battery usage.

See “Accessories” on page 48 for more information on

chargers and other accessories.

NICKEL CADMIUM AND NICKEL METAL

HYDRIDE BATTERIES MUST BE RECYCLED OR

DISPOSED OF PROPERLY. MUST NOT BE DIS-

POSED OF IN MUNICIPAL WASTE.

NiCd

NiMH

In s t a llin g a b a tt e r y

Re m o v in g a b a t te r y

Switch off the phone before removing the battery.

C h a r g in g a b a tt e r y w ith Ra p id Tr a v e l

C h a r g e r (A C H -4 U)

1) Connect the lead from

the charger to the bot-

tom of the phone.

2) Connect the charger to

a standard 120V AC

outlet.

When the battery is charging, the battery

indicator on the right side of the display scrolls.

Allow the battery to completely charge.

Charging is finished when the segments stop

scrolling.

The charging times depend on the type of the

battery and the charger used.

See “Accessories” on page 48 for details.

When charging is finished, disconnect the charger from

the AC outlet and from the phone. When you disconnect

the power cord of any accessory, grasp and pull the plug,

not the cord.

D is c h a r g in g t h e b a tt e r y

Either leave your phone switched on until it turns itself off

or use the battery discharge facility of any approved

accessory available for your phone. The battery can be

charged and discharged hundreds of times but it will

eventually wear out. When the operating time is noticeably

shorter than normal, it is time to buy a new battery.

B a tt e r y C h a r g e

The phone gives you a warning tone

and the message BATTERY LOW when

only a couple of minutes of talk time re-

main. When no more battery power

remains, you get a Recharge Battery

Tone and the message RECHARGE

BATTERY. The phone switches itself off.

Connect your phone directly to a charger or place it on a

charging stand with the power on or off to begin charging.

Note: In some vehicles, the ignition must be on in order to

charge the phone with the cigarette lighter adapter.

If the message NOT CHARGI NG is displayed, charging is

suspended. Check that the battery is not overheated (over

104°F/40°C), too cold, or connected to a non-approved

charging device. Wait for a while, connect the charger to

the phone again and retry. If charging still fails, contact

qualified service personnel.

Im p o r ta n t B a t te r y In fo r m a tio n

For good operation times, discharge the battery from time

to time by leaving your phone switched on until it turns

itself off or by using the battery discharge facility of any

approved accessory available for your phone. Do not

attempt to discharge the battery by any other means.

•

When a charger is not in use, disconnect it from the

power source. Do not leave the battery connected to

a charger for longer than a week; overcharging may

shorten its life.

•

If left unused, a fully charged battery will discharge

itself in about a week at room temperature.

When the battery is not in use, store it uncharged in a

cool, dark and dry place.

•

Temperature extremes affect the ability of your battery

to charge: it may require cooling or warming first.

Do not short circuit the battery. Accidental short cir-

cuiting can occur when a metallic object (e.g. coin,

clip, or pen) causes direct connection of the + and -

terminals of the battery (metal strips on the back of

the battery), for example when you carry a spare bat-

tery in your pocket or purse. Short circuiting the termi-

nal may damage the battery or the connecting object.

•

Use the battery only for its intended purpose.

Never use any charger or battery that is damaged or

worn out.

•

Leaving the battery in hot or cold places, such as in a

closed car in summer or winter conditions, reduces

the capacity and lifetime of the battery. Always try to

keep the battery between 59°F and 77°F (15°C and

25°C). A phone with a hot or cold battery may tempo-

rarily not work, even if the battery is fully charged.

NiMH battery performance is particularly limited in

temperatures below 14°F (-10°C).

•

The battery is a sealed unit with no serviceable parts.

Do not attempt to open the case.

Do not dispose of a battery in a fire! Dispose of used

batteries in accordance with local regulations.

Recycle!

3 . B a s ic s

S w it c h in g O n o r O f f

•

Press and hold

for a second.

When switching on, if your phone has an extendible antenna,

extend the antenna fully. As with any other radio transmit-

ting device, avoid unnecessary contact with the antenna

when the phone is switched on.

Push in the antenna when you are not using the phone.

The phone carries out a short self-test and briefly displays

the phone number in use.

A Personal Reminder Note appears if you have pro-

^{grammed one with Menu 4 5. Press left}ñ ^{( Keep)}to

^{save it or right}ñ ^{( Er as e)}to delete it.

The phone can make and receive calls only when it

is switched on and is located in the cellular net-

work’s service area.

The phone automatically switches itself off if the operating

temperature exceeds 158°F (70°C).

S ig n a l S t r e n g t h

The stronger the radio signal, the better the call

quality. The higher the column on the left side of

the phone display, the better the signal at your

location.

If the signal strength is not good, try moving the

phone slightly. In a building, reception may be

better near a window.

A c c e s s C o d e s

Your phone uses a Security Code or Lock Code to help

protect against unauthorized use of the phone.

Note: Avoid using access codes similar to emergency

numbers such as 911 to prevent accidental dialing of the

emergency number.

Se c u r it y C o d e (5 d ig its )

•

^e^Wⁿ^h^te^e^rnit^th^th^e^e^pnh^p^o^rⁿ^e^e^ss^as^le^k^f^s^tñ^{for th}⁽^e^O^S^K^e⁾^c. ^{ur i t y code: ,}

The Security Code comes with your

phone and is required with some

phone features. Keep it secret and in a

safe place, separate from the phone.

You cannot change the Security Code.

If you need a new one, contact your

dealer. The default is 12345.

If you enter an incorrect security code ( CODE ERROR)

five times in a row, the phone won’t accept any entries for

the next five minutes.

L o c k C o d e

•

^W^pre^h^s^e^sⁿ^l^t^e^h^ft^eñ^phon⁽^e^O^a^K^s⁾^k.^{s for the lock code, enter it then}

You need the 4-digit lock code to turn

on the Automatic Phone Lock in

Menu 5 1. The default Lock Code is

1234.

4 . M a k in g a n d R e c e iv in g

C a lls

A n s w e r in g a C a ll

•

Press any key (except

then speak.

ð,

or volume keys)

With KEYS LOCKED, only

to stop the ringing sound, without answering the call.

answers calls. Press

M a k in g a C a ll

1) Extend antenna fully.

2) Key in phone number.

3) Press

Your phone can make and receive calls only when it is

switched on and in the cellular network’s service area,

and not set to Message Mode (see “Message Mode” on

page 16).

NO SERVI CE means that you are probably outside the

cellular service area. No calls can be placed or received.

If you try to make a call while NO SERVI CE is displayed,

the phone displays WAI T FOR SERVI CE, and tries to

make the call for the next 2 minutes.

Note: Check with your cellular system operator for infor-

mation about when you need to dial a ‘1’ and/or an area

code in addition to the number.

1) Press

^{If yo u m}ù^{a k e a m is t a k e e n t e r in g a n u m b e r}

once to delete the last digit, or

2) Press and hold

to clear the whole display.

H a n g in g u p

•

Press

S p e e d D ia lin g

1) Enter the memory location number (2 to 99).

2) Press

The phone recalls the phone number from the memory,

displays it briefly, then dials it.

^{Note: If you press 1}í, the phone dials the number

page 15). If you press 9

gency call only if Menu 3 4, Emergency Key 9, is set to On.

^{stored with Menu 2 3, S}í^{et Voice Mailbox Number (see}

, the phone initiates an emer-

L a s t N u m b e r R e d ia l

1) Clear display with

2) Press

Re d ia lin g a n y o f t h e la s t 5 n u m b e r s

1) Press then W or V within a second.

2) Once you see the number you want, press

to dial it.

^{Note: After}í, you must press W or V within a second

to scroll through the last 5 dialed numbers. Otherwise, the

phone automatically dials the most recently dialed number.

O n e - To u c h D ia lin g

•

Press and hold the key (2 to 8) for a few seconds until

the call is started.

The phone recalls the phone number from memory, dis-

plays it briefly, then dials it. To use this feature, Menu 3 3,

One-Touch Dialing, must be On and you must have stored

numbers in the location corresponding to the number you

pressed. See “The Personal Directory” on page 19 for

details on storing numbers.

Note: If you press and hold 1, the phone dials the number

stored with Menu 2 3, Set Voice Mailbox Number (see

page 15). If you press and hold 9, the phone initiates an

emergency call only if Menu 3 4, Emergency Key 9, is set

to On.

Im p o r ta n t !

Official emergency numbers vary by location (e.g. 911 or

other official emergency number). Only one emergency

number is programmed into your phone to be dialed

automatically by Emergency Key 9, which may not be the

proper number in all circumstances. Emergency Key 9

dialing does not operate with KEYS LOCKED or when the

phone is connected to a modem.

Em e r g e n c y K e y 9

Note: Emergency Key 9 works only if it has been set

to On in Menu 3 4!

1) Press 9 then

2) Press and hold 9 for more than 3 seconds.

The phone dials the preprogrammed emergency number

(e.g. 911) with either of these dialing methods. You can

also dial an emergency number by keying in the whole

emergency number then

Note: Pressing and holding Emergency Key 9 to dial an

emergency call does not function with KEYS LOCKED or

when the phone is connected to a modem. (See “Key Lock”

on page 13 later in this chapter for more information on

Key Lock.)

Vo ic e M a il K e y 1

•

Press and hold

for a few seconds.

The phone dials the number stored with Menu 2 3, Set

Voice Mailbox Number. See “Voice Messages” on page 15

for more information.

Ea r p ie c e Vo lu m e

The volume button on the side of the phone adjusts the

earpiece volume. The upper part of the button increases

and the lower part decreases the volume.

If an accessory with its own loudspeaker is connected to the

phone, the volume keys select the volume for that accessory.

^M1) ^u^P^ti^rⁿ^es^g^s^/^a^Uⁿⁿ^d^m^ho^u^ld^ti^leⁿ^f^g^tñ^{th e}⁽^p^Me^hⁿ^o^uⁿ⁾^ef^’o^sr f^mew^ics^re^oco^pn^hds^o.^{n e}

2) Press W to Mut e or Unmut e.

3) ^{Press left}ñ ^{( OK)}.

Muting and unmuting may be done only during an active call.

C a llin g L in e Id e n t if ic a t io n

If you have subscribed to and activated this network ser-

vice, the phone displays the caller’s phone number if the

system is able to identify it. The phone displays the caller’s

name if you have stored that caller’s name and number,

and the person calls you from the number you have stored.

The phone also displays a caller’s name if the network

supplies it, even if you don’t have the person’s name

stored in your phone.

CALL or NO I D CALL displays when the number is not

available. PRI VATE I D CALL displays when the caller

has prevented the number from being shown.

Note: For information about availability of and subscription

to Calling Line Identification, contact your system

operator.

S p e c ia l R in g in g To n e

You may set your phone to a special ring when particular

people call. To do this, store the person’s name and

number in your phone and include the character “!” some-

where in the person’s name (e.g. Joe!Smith). When that

person calls you from that number, you’ll know it by the

special ring you hear. For details on storing names and

numbers, see “The Personal Directory” on page 19.

Note: Special Ringing Tone works only when Calling Line

Identification is active and the calling number is available.

K e y L o c k

•

Press and hold ô, or press left

then ∗.

phone is in your pocket). Press left

^{Key Lock prevents accidental key p}ñ^{resses (e.g. when the}

the keypad.

then ∗ to unlock

Key Lock cannot be activated when the phone is connected

to a car kit or a handsfree desktop charger.

^N^em^ot^e^e^r:g^W^en^it^c^h^y^Kⁿ^e^u^y^m^s^b^Leo^r^c9k¹^e¹^d,⁽⁹^c¹^a¹^llí^{s ma}).^yP^br^ees^ps^oin^sg^si9^blí^{e to t}s^hh^eould

also work, if Menu 3 4, Emergency Key 9, is set to ON.

However, pressing and holding Emergency Key 9 does

not function.

When placing an emergency call, the emergency number

will be displayed only after you have keyed in all its digits.

After the emergency call, Key Lock becomes active again.

A n s w e r in g a c a ll w it h K e ys L o c k e d

•

Press

During the call the keypad remains unlocked which lets

you operate the phone as usual. After you end the call, Key

Lock becomes active again.

C a ll W a it in g

With Call Waiting, the active call is put on hold as you

answer the waiting (incoming) call. This service is available

only if you have subscribed to it through your network

operator. For details on Call Waiting availability and

operation, check with your network operator.

Note: If you do not answer a waiting call, the calling phone

number (if available) is added to the Missed Calls List.

C a llin g C a r d C a lls

If you use the phone’s Calling Card storage feature

(see “Menu 3 7, Calling Card” on page 33), you can use

the method described below. You won’t need to enter

Calling Card information every time you want to make a

card call.

Note: No physical credit cards are needed in order to

direct the call charges to the credit card.

To m a k e a C a llin g C a r d C a ll

1) Enter the phone number of the party to be called, be-

ginning with a 0 or a 1 if your calling card requires you

to enter a 0 or a 1 before the area code and phone

number. See your calling card for instructions.

2) Press and hold

for 3 seconds, until the phone

displays CARD CALL.

3) When you hear a tone or voice prompt, press left

( OK).

4) If you get another tone or voice prompt, press left

ñ ^{( OK)}again.

The call is then made, as if you had manually entered the

card information.

5 . Vo ic e a n d Te x t M e s s a g e s

Please check with your operator for the availability of

message features.

Vo ic e M e s s a g e s

When you receive a voice message, the phone beeps,

lights the voice message indicator (

), and displays NEW

VOI CE MESSAGE. The phone shows the number of mes-

sages if there are more than one.

To use the methods described below to call your voice

mailbox, you must store your voice mailbox number in

your phone, which is described in this section.

To c a ll yo u r v o ic e m a ilb o x a ft e r r e c e iv in g

a m e s s a g e

With NEW VOI CE MESSAGE on display,

1) ^{Press left}ñ^{( Li s t en)}OR

2) Press

Note that your voice mailbox number must be stored in the

phone to use this method (see below).

To c a ll yo u r v o ic e m a ilb o x a n y t im e

•

Press and hold 1

You can also call your voice mailbox by pressing left

( Menu) 2 1.

To s to r e yo u r v o ic e m a ilb o x n u m b e r in

^t1^h) ^e^Pr^p^es^h^s^o^leⁿ^ft^eñ ^{( Menu)}2 3.

2) Key in voice mailbox number.

3) ^{Press left}ñ ^{( OK)}.

Once you enter the number, it is used until you change it again.

Note: The voice mailbox may be provided by the network

(and the network operator gives you the number to call).

M e s s a g e M o d e

•

Press left ñ ^{( Menu)}#. (This also sets Message

Mode off if it is on.)

1) ^{Press left}ñ ^{( Menu)}3 8.

2) Press W to On.

3) ^{Press left}ñ ^{( OK)}.

With “Message Mode” set to On, you can receive Voice

Mail Notification and Text Messages. You do not receive

any incoming calls. The phone displays MSGS ONLY. The

default setting is Off. “Message Mode” is a network service.

Please check for the availability from your network operator.

Te x t M e s s a g e s

When the text message network service is available and

you have subscribed to it, your phone can receive and

store text messages. The text message function is a net-

work service and may not be supported by your network.

Also, to use text messaging, you must have the phone

number of your message service center available.

The phone can store up to 30 text messages, with a

maximum of about 1,900 characters for all messages

combined. Contact your network operator for details

about the text messaging service and the maximum

number of characters allowed in a message.

The network may have its own default message that is dis-

played when the phone is in the network coverage area.

This does not prevent the use of your phone in any way.

Re a d in g Te x t M e s s a g e s

When you receive a text message and there is enough space

left in the message memory, MESSAGE RECEI VED (or NEW

URGENT or NEW EMERGENCY MESSAGE if applicable)

and the indicator (

) are displayed. See “The Display”

on page ii for a description of the Text Message indicator.

To r e a d m e s s a g e s im m e d ia t e ly

•

With MESSAGE RECEI VED on display, press left

( Read).

To r e a d te x t m e s s a g e s a n y tim e

1) ^{Press right}ñ ^{( Qui t )},then later:

2) ^{Press left}ñ ^{( Menu)}2 2.

3) Press W to view the first message.

4) Scroll message(s) with W or V.

The messages are shown in the order that they were re-

ceived or stored. New messages are shown first, in their

order of priority, then old messages, in their chronological

order.

NEW indicates an unread message and is followed by the

date and time of receipt.

OLD indicates that the message has already been read.

URGENT indicates that the message received was marked

“urgent” by the sender.

EMERGENCY indicates that the message received was

marked “emergency” by the sender.

LOCKED indicates that you have locked the message.

It will not be overwritten even if there is no more space in

memory and there is an attempt to deliver a new message

to your phone.

To D ia l a N u m b e r in a M e s s a g e

While the phone number in the message is displayed,

press

Te x t M e s s a g e O p t io n s

With message on screen,

1) ^{Press left}ñ ^{( Opt i on)}.

2) Press W to option you want.

3) ^{Press left}ñ ^{( OK)}.

Read next shows the next message.

Er as e deletes the current message from memory.

Lock/ Unl ock allows you to lock and unlock messages.

When a new message arrives and the message memory is

full, the new message automatically overrides old messages

unless they are locked.

Us e Number lets you edit or call the number currently

shown on the display. After selecting Us e Number , you

get the options Edi t and Qui t .

To edit the number (e.g., add or remove digits), press

Edi t . Use W or V to move the cursor right or left.

Use

of the cursor. You can dial the number on display any time

by pressing

to backspace over (delete) the number to the left

6 . T h e P e r s o n a l D ir e c t o r y

You can store up to 100 numbers and associated names

in your “Personal Directory”.

Stored numbers may be up to 16 digits long. Stored

names may be up to 16 characters long. The phone pro-

vides you with 8 extended number locations (any you

choose) that allow the stored number to contain up to 30

digits in addition to the name.

The identical name may be used only once in memory.

REPLACE NAME? appears when you try to store a name

already in memory.

A lp h a M o d e

To enter, retrieve, and view names, press ÷. The phone

displays ABC, meaning you can use keys to enter letters as

well as numbers, and you view names rather than

numbers.

When a number is displayed, press

ated name (if there is one). When a name is displayed,

press to see the associated number.

to see the associ-

When ABC is displayed, you can enter these characters:

K e y C h a r a c t e r s K e y

C h a r a c t e r s

PQRS7

∗

ABC2

DEF3

GHI4

JKL5

TUV8

WXYZ9

- ? ! , : ” ’ & $ ( ) 0

Advance to the next

space

MNO6

Blank space

Note: If you include the character ! in the stored name, the

phone rings distinctly when receiving calls from that num-

ber. See “Special Ringing Tone” on page 12 for more

information.

When ABC is not displayed, you can use the ∗ key to enter

these special characters:

Pr e s s

To G e t Th is Sp e c ia l C h a r a c te r :

Th is K e y:

óó

+, links memory locations together

p, creates a pause

óóó

óóóó

w, causes the phone to wait for input

En t e r in g N a m e s

1) Press

2) Press and release the key labeled with the letter you

want until that letter appears.

3) For another letter on the same key, press ∗ in

between letters or wait a few seconds. To erase a

letter if you make a mistake, press

To e n te r u p p e r /lo w e r c a s e

If you press and hold the key when entering letters, the

phone switches the letter from upper to lower case and

vice versa. For example, press and hold 2 to switch from

A to a. The phone stays in “lower case” until you press and

hold a key again to switch to upper case.

Ex a m p le N a m e : L is a

P r e s s t h is

Fo r t h is e ffe c t

alpha mode

5 5 5

press and hold 4 , then 4 4

l (lower case)

7 7 7 7

S t o r in g N u m b e r s a n d N a m e s

1) Key in phone number.

2) ^{Press right}ñ ^{( Memor y)}.

3) ^{Press left}ñ ^{( St or e)}.

4) Key in name (optional).

5) ^{Press left}ñ ^{( St or e)}^.

6) ^{Press left}ñ ^{( OK)}.

You can also enter another location number or scroll

through available location numbers with W or V after

the STORE I N LOCATI ON? prompt.

To fa s t s a v e

1) Key in phone number.

2) ^{Press and hold right}ñ ^{( Memor y)}.

To a d d a n a m e t o a s t o r e d p h o n e n u m b e r

1) Recall the stored number, and remember its location

(shown in upper right corner of the display).

2) Press

then key in name.

3) ^{Press right}ñ ^{( Memor y)}then left ñ ^{( St or e)}.

4) At STORE I N LOCATI ON? enter the location

number from step 1.

5) ^{Press left}ñ ^{( OK)}then left ñ ^{( OK)}again at

REPLACE?

To c h a n g e t h e n u m b e r s t o r e d w it h a

n a m e

1) Recall the stored number.

2) Press

repeatedly to erase number.

3) Key in new number.

4) ^{Press right}ñ ^{( Memor y)}.

5) ^{Press left}ñ^{( St or e)}then left ñ ^{( OK)}again at

REPLACE?

To e r a s e s t o r e d n a m e s a n d n u m b e r s

With display empty,

1) ^{Press right}ñ ^{( Memor y)}.

2) ^{Press left}ñ ^{( St or e)}then left ñ ^{( St or e)}

again.

3) Press W to name you want to erase, or key in name,

or press

to see numbers, then W.

4) ^{Press left}ñ ^{( Er as e)}^.

^{ñ ( Qui t ) instead o}ñ^{f left}^{( Qui t )}again to

Press right

you change your mind. Press right

exit the erase function. You may also use Menu 01 5 to

erase.

ñ ^{( Er as e)}if

Note: You cannot undo Erases so be careful!

To e r a s e a ll s to r e d n u m b e r s

1) ^{Press left}ñ ^{( Menu)}01 5.

2) Press W to Er as e Al l then left ñ ^{( OK)}.

3) ^{Press left}ñ ^{( OK)}at ARE YOU SURE?

R e c a llin g S t o r e d N u m b e r s

•

With display empty, press W or V.

Press W or V repeatedly to scroll through stored

numbers. Press to see corresponding names.

R e c a llin g S t o r e d N a m e s

•

With display empty, press

Press W or V repeatedly to scroll through stored names.

Press to dial the displayed name’s number.

then W or V.

To r e c a ll n u m b e r s b y m e m o r y lo c a tio n

1) Key in location number.

2) ^{Press right}ñ ^{( Memor y)}.

3) Press right ñ ^{( Fi nd)}.

Press to dial the displayed number or displayed

name’s number.

To r e c a ll n u m b e r s b y n a m e

1) ^{Press right}ñ ^{( Memor y)}.

2) Key in name or its first few letters.

3) ^{Press right}ñ ^{( Fi nd)}^.

If you enter only the first letters of the name and there is

more than one name beginning with these letters, press W

or V until you see the name you want.

Sta t u s o f th e D ir e c to r y

1) ^{Press left}ñ ^{( Menu)}01 6.

2) Press W to show the number of empty locations.

3) Press W again to show the number of full locations.

7 . Te m p o r a r y L is t s

& C a ll Tim e r s

The phone automatically stores the last 5 dialed numbers,

and calling numbers of the last 5 answered and last 5

missed calls.

Note: The phone displays the phone numbers of received

and missed calls only if the cellular system is able to iden-

tify the caller and you have subscribed to this service.

To v ie w D ia le d N u m b e r s

1) With display empty, press

2) Press W or V within a second.

The top right corner of the display shows the location

number of the last dialed number (L0 - L4). You may also

use Menu 01 1, Dialed Calls. Once you see the number

you want, press

to dial.

To v ie w L a s t R e c e iv e d C a lls

•

With display empty, press ∗ then W to scroll the

numbers.

The top right corner of the display shows the location

number of the 5 most recent calls you have answered

(R0-R4). Press

You may also use Menu 01 2, Received Calls.

to view associated names, if available.

To v ie w M is s e d C a lls

•

With display empty, press ∗∗ (+) then W.

If MI SSED CALLS is displayed, press left

( Li s t ) then W to scroll the list, OR

•

^{Press right}ñ ^{( Qui t )}to view the numbers later,

using ∗∗ W or Menu 01 3.

The top right corner of the display shows you the location

number (U0-U4) of the calling phone numbers of the 5

most recent calls you have not answered. Press

view associated names, if available. You may also use

Menu 01 3, Missed Calls.

To c le a r t e m p o r a r y lis ts

•

^{Press left}ñ ^{( Menu)}01 4.

This clears Dialed Numbers, Received Calls, and Missed

Calls. You cannot undo this operation so be careful!

C a ll Tim e r s

1) Press left ñ ^{( Menu)}01 7.

2) Press W to the timer you want to see.

This shows call durations for the currently-selected NAM

(phone number). The phone has separate timers for each

NAM your phone uses. See “Menu 8, NAM Selection” on

page 43 for more information about NAMs.

Note: The actual time invoiced for calls by your service

provider may vary, depending upon items such as network

features, rounding off for billing, and taxes.

^T1)^o^P^c^re^le^ss^a^l^r^ef^C^tñ^{a ll T}^{( M}^im^en^e^u^r⁾^s0⁽1^e7^x. ^{c e p t L ife Tim e r )}

2) Press W to CLEAR TI MERS.

3) ^{Press left}ñ ^{( OK)}.

4) Key in security code at Secur i t y code: then left

ñ ^{( OK)}.

Note: Life Timer cannot be cleared. It records the total

amount of time for all calls made and received with this

phone.

8 . To u c h To n e s

Your phone is a “Touch Tone” phone, meaning that it creates

certain sounds when you press the keys. These sounds

can be used for many automated, over-the-phone services

such as checking your bank balance, using your voice

mailbox options, and even checking airplane arrival and

departure times.

Touch Tones are called “DTMF” (Dual Tone Multifrequency)

tones in the phone.

S e n d in g In d iv id u a l To u c h To n e s

•

Press keys during call.

Touch Tones can be used only when a call is active.

You would use the Individual Touch Tone feature when, for

example, you are prompted to “press 1 and then the star

(∗) button”. You would simply press 1 ∗.

Note: Individual Touch Tones can be sent only if Menu 4 3

is not set to Off. Menu 4 3 is described on page 35.

S e n d in g S t r in g s o f To u c h To n e s

During a call, with the display empty:

1) Recall from memory the string you want to send.

2) ^{Press left}ñ ^{( Menu)}then

You can store a whole digit sequence in a memory loca-

tion and send it as Touch Tones. You could use this for

frequently-used strings of numbers, such as the access

codes for your voice mailbox.

rently on the display. You may also press and hold left

^{The phone sends (as Touch Tones) the digits that are}ñ^cur-

ñ^{( OK)}

⁽^th^M^e^eⁿⁿ^le^u^f⁾^tñ^then⁽^p^Q^re^u^sⁱ^s^t^W⁾^tt^oo^Sse^enⁿd^da^Ds^Ttr^Min^Fg^tho^efⁿTo^leu^ftch Tones.

To s to r e a To u c h To n e s t r in g

Store Touch Tone strings the same way as you store

phone numbers.

For example, you could store a voice mail number in the

personal directory.

To s to r e To u c h To n e s t r in g s w it h a p h o n e

n u m b e r

1) Key in the phone number.

2) Press ∗∗∗ (p) or ∗∗∗∗ (w).

3) Key in the Touch Tone string.

4) Store the number in the normal way.

∗∗∗ creates a “p” (pause) character. When you recall this

^{number sequence from memory and press}í, the

phone dials the phone number, pauses 2.5 seconds, then

sends the DTMF digits. You can add as many “p”

characters as you need to get the right delay time.

number sequence from memory and press

^{∗∗∗∗ creates a “w” (wait) character. When y}í^{ou recall this}

, the

phone dials the phone number, then waits for you to press

^{the left}ñ^{( DTMF)}^.This is handy if you are calling a num-

ber that then prompts you to enter information, such as

someone’s phone extension.

To lin k a s t o r e d p h o n e n u m b e r to D TM F

d ig it s in a n o th e r m e m o r y lo c a t io n

1) Key in the phone number.

2) Press ∗∗ (+).

3) Key in memory location storing the DTMF string.

4) Store the number in the normal way.

Use this if the phone number and DTMF digits do not fit in

one storage location; it links the phone number to the

memory location storing the DTMF string.

∗∗ creates a “+” (link to another memory location). When

you recall this number sequence from memory and press

í, the phone dials the phone number, then displays

digits stored in the memory location you have entered.

^{Press left}ñ ^{( DTMF)}to send them.

Entering only a “+” at the end of a stored number causes

the phone to prompt you for a memory location after the

call is connected. The phone expects a memory location

^a^le^f^f^tteñ^{r the}⁽^“+^O^”^K^c⁾^h.^aT^rh^ae^cn^tep^r.re^Esⁿs^tele^rf^at ñ^locat⁽^io^Dⁿ^Tⁿ^M^u^F^m⁾^bw^erh^aeⁿn^dth^pe^ress

phone displays the digits stored in that memory location.

To u c h To n e S e t t in g s in t h e P h o n e

Your phone’s Touch Tone settings are Menu 4 3, Manual

DTMF Tones, and Menu 4 4, Auto DTMF Length.

M e n u 4 3 , M a n u a l D TM F To n e s

1) ^{Press left}ñ ^{( Menu)}4 3.

2) Press W to your choice.

3) ^{Press left}ñ ^{( OK)}.

This determines the length of the individual Touch Tones

when you press keys during calls. Note that regardless of

this setting, strings of Touch Tones can be sent.

Cont i nuous means the tone sounds for as long as you

hold the key. Fi xed sets the tone length to 100 ms,

regardless of how long you press the key. Of f turns the

tones off, meaning that no tones are sent when you press

individual keys.

^M1) ^e^Lⁿ^e^u^ftñ^{4 4}⁽^,^M^A^e^uⁿ^t^u^o⁾4^D4^T. ^{M F L e n g th}

2) Press W to your choice.

3) ^{Press left}ñ ^{( OK)}.

This determines the length of Touch Tones in strings.

Shor t sets the DTMF tone length to 100 ms. Long sets

the DTMF tone length to 500 ms.

9 . T h e M e n u

The phone’s menus and submenus give access to most of

the phone’s functions.

M e n u g u id e lin e s

1) ^{Press left}ñ ^{( Menu)}to enter the menus.

2) Press W and V to step through menus, submenus,

and options.

gives help text on menus and submenus and

goes to the next screen of help text if there are

several.

4) ^{Press right}ñ ^{( Qui t )}to go back one level.

5) exits the menu facility without making changes.

^S1)^{c r}^P^o^re^l^s^li^sⁿ^l^g^eft^tñ^{h r o}⁽^u^M^g^e^h^nu^t⁾^h.^{e m e n u s}

2) Press W or V to menu you want.

3) Press left

(Sel ect or OK) to enter submenus

and choose options.

The current setting appears first in lists of setting options.

En t e r in g m e n u s b y n u m b e r (s h o r t c u ts )

•

^{Press left}ñ ^{( Menu)}then menu number then sub-

menu number then setting number.

The menus, submenus and setting options are numbered.

The number is shown in the display’s top right corner.

Once you reach the menu or submenu you want, you can

also use W or V to see options.

Note: Press the menu, submenu, and setting numbers

within a couple of seconds of each other when using this

method.

S u m m a r y o f M e n u Fu n c t io n s

a n d S h o r t c u t s

M e m o r y Fu n c t io n s

M e n u 0 1

Countdown Timer

Restore Settings

Language

Dialed Calls

Received Calls

Missed Calls

Clear All Call Lists

Memory Erase Options

Memory Status

Call Timers

Se c u r it y O p t io n

M e n u 5

Automatic Phone Lock

Change Lock Code

Restrict Calls

3 1 Outgoing Calls

3 2 International Calls

3 3 Incoming Calls

M e s s a g e s

M e n u 2

Listen to Voice

Messages

N e t w o r k Se r v ic e s

M e n u 6 (see note next page)

Read Messages

Set Voice Mailbox

Number

Public Systems

Dual Mode Selection

Voice Privacy

Call Forwarding

4 1 Forward All Calls

4 2 Forward If Busy

4 3 Forward If Not

Answered

C a ll Se t t in g s

M e n u 3

Ringing Volume

Ringing Tone

One-Touch Dialing

Emergency Key 9

Automatic Redial

Automatic Answer

Calling Card

4 4 Forward If Out of

Reach

4 5 Cancel All

Forwarding

Message Mode

Call Waiting

Send Own Number

Network Feature Setting

P h o n e Se t tin g s

M e n u 4

Lights

Keypad Tones

Manual DTMF Tones

Auto DTMF Length

Personal Reminder

Note

Sys te m Se a r c h

M e n u 7

M e n u 6 N o t e : The items

in Menu 6 shown in italics are

visible ONLY when activated

with Menu 6 7!

Selects which cellular

system to use.

N A M Se le c t io n

M e n u 8

N e t w o r k Se r vic e s

Some of the menu functions

are network services. These

functions can be utilized only

if provided by your cellular

network. To make use of a

network service, you must

first subscribe to it. For avail-

ability and subscription,

contact your network

Selects the phone’s system

and current phone number.

N u m b e r Ed it o r

M e n u 9

Allows editing of the

currently-displayed number.

operator.

A le r t O p t io n s

M e n u 10

Selects type of ringing or

silent service.

L o c k Th e K e ys

M e n u 11

Locks the keypad.

M e n u 0 1, M e m o r y Fu n c t io n s

See “The Personal Directory” on page 19 and “Temporary

Lists & Call Timers” on page 24 for descriptions of the

items in Menu 01.

M e n u 2 , M e s s a g e s

See “Voice and Text Messages” on page 15 for descriptions

of these menu items.

M e n u 3 , C a ll S e t t in g s

M e n u 3 1, Rin g in g Vo lu m e

You hear each ringing level as you scroll through the vol-

ume levels. When the phone is connected to a handsfree

desktop charger, handsfree car kit, or headset, the ringing

volume can be set separately for those accessories.

M e n u 3 2 , Rin g in g To n e

The phone plays a sample of each pattern as you scroll.

Note: The ringing tone is the same for all accessories.

M e n u 3 3 , O n e -To u c h D ia lin g

With this feature on, you can dial any of the phone num-

bers stored in personal directory locations 2-9 by pressing

and holding the number of the personal directory location.

Note: Pressing and holding 9 initiates an emergency call if

the Emergency Key 9 function is set On! Pressing and holding

1 always initiates a call to the number stored with Menu 2 3,

Set Voice Mailbox Number.

M e n u 3 4 , Em e r g e n c y K e y 9

With this feature on, the phone makes an emergency call

^{when you press 9 then}í. The phone dials the prepro-

grammed emergency number (e.g. 911).

You can also dial an emergency call by pressing and holding

9 for about three seconds, after which the call is initiated.

However, this method does not work when Key Lock is

active or when the phone is connected to a modem.

M e n u 3 5 , A u t o m a t ic Re d ia l

When this is on, your phone redials the number you are

tone) up to 10 times. Press

The phone beeps when the call goes through.

^{trying to call (if the network is}ô^{busy, indicated by a fast busy}

to end the call attempts.

M e n u 3 6 , A u t o m a t ic An s w e r

When the phone is connected to the headset or the

handsfree facility of the car kit, you can set the phone to

answer a call automatically after one ring. The car kit must

be equipped with the ignition sense option.

M e n u 3 7 , C a llin g C a r d

Your phone can store up to 4 calling cards.

1) ^{Press left}ñ ^{( Menu)}3 7. The phone lists Car d

A- D or None.

2) Press W until you see the card you want then press

^leftñ ^{( OK)}. This is the card your phone will auto-

matically use when you make calling card calls (see

“Calling Card Calls” on page 14 ). To use a different

card, select it and go through the steps again. The

phone will display previously-stored information.

3) ^{Enter your Security code then press left}ñ ^{( OK)}.

This gives you the SELECT DI ALI NG SEQUENCE

screen.

4) ^{Press left}ñ^{( Sel ect )}, scroll through the choices,

^{and press left}ñ ^{( OK)}for the one that matches

your calling card.

O p tio n

Us e fo r c ard s th at r e q uire yo u to :

Access No. Dial 1-800 access number, then phone number, then

+ Phone No. card number

+ Card No.

Access No. Dial 1-800 access number, then card number, then

+ Card No. phone number

+ Phone No.

Prefix

Dial a prefix (such as 0 or 1), then phone number,

+ Phone No. then card number.

+ Card No.

5) The phone then prompts you for other information,

such as Acces s number and Car d number.

Enter this information at each prompt and press left

ñ ^{( OK)}.

6) You can enter the calling card name by pressing

when the phone prompts you for the access number

^o^th^r^e^c^c^a^a^rd^rdⁿⁿ^u^a^m^m^b^e^e^.^r.^E^Tnh^t^e^er^p^it^h^a^oⁿⁿ^d^e^p^w^rⁱ^e^ll^s^th^s^e^leⁿ^ft^pñ^romp⁽^t^O^y^K^o⁾^u. ^for

To change stored calling card information (such as

your card number), go through these steps, but use

the

the new information then press left

^{key to erase already stored i}ñ^nform⁽^a^O^ti^K^o⁾ⁿ.^{. Key in}

M e n u 3 8 , M e s s a g e M o d e

See “Message Mode” on page 16 for a description of this

function.

M e n u 4 , P h o n e S e t t in g s

M e n u 4 1, L ig h ts

With lights on, the keypad lights come on when you press

a key or have an incoming call, and go off 15 seconds

later.

When the phone is connected to a car kit, desktop charger,

or cigarette lighter charger, the keypad lights are on

permanently when this setting is ON; when this setting is

OFF, the lights come on when you press a key or have an

incoming call, and go off 15 seconds later.

Note: You can turn on the lights for 15 seconds by pressing

the power key quickly, regardless of this setting.

M e n u 4 2 , K e yp a d To n e s

You can select the volume level or turn off the sound the

phone makes when you press a key.

Note: The keypad tone volume is set separately for each

accessory you use.

M e n u 4 3 , M a n u a l D TM F To n e s

M e n u 4 4 , A u t o D TM F L e n g th

See “Touch Tones” on page 26 for descriptions of these

items.

M e n u 4 5 , P e r s o n a l Re m in d e r N o t e

1) ^{Press left}ñ ^{( Menu)}4 5.

2) Key in a new message or edit the existing one.

3) Press left

( Opt i on).

4) Press W to St or e or Er as e.

5) ^{Press left}ñ ^{( OK)}.

The Personal Reminder Note displays when the phone is

switched on. The maximum length is 30 characters.

Characters you key in are added to the left of the cursor.

Press

to delete characters to the left of the cursor.

Press W or V to move the cursor right or left. St or e

stores the new or edited note for later use. The note is

displayed each time you switch the phone on. Er as e re-

moves the note from the display and from the memory.

^{Next time you switch the phone on, the stored no}ñ^te

^d( ⁱK^se^ple^ap^ys)^.t^Ooⁿs^ca^eve^yoit^uo^hr^ar^vig^eh^rt^eñ^{ad th}⁽^e^Eⁿ^r^o^a^te^s^,^e^p⁾^ret^so^sd^lee^fle^tte it. It

displays each time you turn the phone on until you erase it.

M e n u 4 6 , C o u n t d o w n Tim e r

1) ^{Press left}ñ ^{( Menu)}4 6.

2) Key in time to count down at Set t i mer : . Enter

hours 00-99 and minutes 00-59.

3) ^{Press left}ñ ^{( OK)}.

4) ^{Press right}ñ ^{( Qui t )}twice to exit.

The phone sounds an alarm and displays COUNTDOWN

COMPLETED when it finishes counting down the amount

of time you enter. The timer stops if the battery runs out or

if you turn the phone off.

An incoming call overrides the timer alarm. After you have

completed the call, COUNTDOWN COMPLETED appears,

but the phone does not sound an alarm.

To s to p th e tim e r b e fo r e it a la r m s

•

Follow the steps above, but key in 0000 at Set

t i mer : .

•

Press any key except

^{To c le a r t h e a la r m}ð^{w h e n it is s o u n d in g}

M e n u 4 7 , Re s to r e Se tt in g s

You can reset the settings of certain menu functions to

factory defaults (as in a new telephone).

Note: The memory, timers, counters, and language

are not reset.

The following settings are set to the values shown:

Ringing Volume

Ringing Tone

Level 4 (3 in car mode)

Type 1

Off

One-Touch Dialing

Emergency Key 9

Automatic Redial

Automatic Answer

Message Mode

Lights

Keypad Tones

Manual DTMF Tones

Auto DTMF Length

Level 2

Continuous

Long

Automatic Phone Lock Off

Lock Code

1234

Dual Mode Selection

Voice Privacy

Ana. & Dig.

Off

Ringing Options

Ring

M e n u 4 8 , L a n g u a g e

You can choose the language your phone uses for all of its

displays: English, French, Spanish or Portuguese.

M e n u 5 , S e c u r it y O p t io n s

Most of the phone’s security features require a five-digit

security code, which is normally supplied with your phone.

The default is 12345. If you forget the security code, con-

tact your dealer. Since this code allows access to all the

operations of the phone, store it in a safe place, separately

from the phone.

M e n u 5 1, Au to m a tic P h o n e L o c k

When you turn this on, the phone’s lock becomes active

after you switch the phone off and back on. With the lock

on, the phone prompts you to Ent er l ock code: to

access memory and menu functions.

To e n te r t h e lo c k c o d e :

^p^A^r^t^e^E^sⁿ^s^t^le^e^ft^rñ^{l oc}⁽^k^OK^c⁾.^{ode: key in the lock code then}

•

When the phone is locked, calls may be possible to the

emergency number programmed into your phone (e.g. 911

or other official emergency number) including calls with the

Emergency Key 9. Also, you may call the number stored in

location 100.

To a n s w e r a c a ll w ith A u t o L o c k o n :

•

Press

To c a ll th e n u m b e r in lo c a t io n 10 0 w it h

A u t o L o c k o n :

•

Press W or V then

Note: To unlock the phone permanently after locking it,

you need to enter this function and select the AUTO LOCK

OFF option.

M e n u 5 2 , C h a n g e L o c k c o d e

In a lock code, only digits 0 to 9 are accepted. Lock codes

are four digits long.

M e n u 5 3 , Re s t r ic t C a lls

You can prevent the phone from dialing a number or receiving

a call. When calls are restricted, calls may be possible to

the emergency number programmed into your phone

(e.g. 911 or other official emergency numbers).

M e n u 5 3 1, O u t g o in g C a lls

Al l owed means that all calls can be made as usual.

Bl ocked means that no calls can be made. Li mi t ed

means that calls can be made only to phone numbers

stored in certain personal directory locations. You are

prompted for a FROM: and TO: value. For example, enter

FROM: 1 and TO: 15, to allow only calls to the numbers

stored in locations 1-15. Or, enter FROM: 3 and TO: 3, to

allow only calls to the number stored in location 3.

You can store an area code (for example, 214) in a mem-

ory location (e.g., 15). Then select Li mi t ed, and enter 15

in the FROM: and TO: values. You can then make calls to

only numbers starting with 214.

M e n u 5 3 2 , In te r n a t io n a l C a lls

Al l owed means you can make international calls

(i.e., calls beginning with the international prefix prepro-

grammed in your phone). Bl ocked means you can’t

make international calls with the phone.

M e n u 5 3 3 , In c o m in g C a lls

Al l owed means you can receive all calls. Bl ocked

means you can receive no calls.

M e n u 6 , N e t w o r k S e r v ic e s

M e n u 6 1, P u b lic Sys t e m s

The phone uses the setting of this item to determine which

public system to use. See “Menu 7, System Search” on

page 43, for more information about the systems your phone

can work in.

In each cellular service area there are usually two cellular

operators operating public systems of type “A” or “B”.

One of the public systems (A or B) is your home system

(depending on your operator) but your phone can work

with both types of systems. With Menu 7, you can select

the type of system the phone should use.

(If you have registered with several operators, use Menu 8,

NAM SELECT, to select a NAM. This determines which

phone number and “home system” the phone uses.)

Bot h A&B means that when roaming, the phone first tries

to use a home-type system (such as “B” if the home sys-

tem is B). If this is not available, it then tries to use a non-

home type system (such as “A” if the home system is B).

Homet ype A or Homet ype B means the phone tries

to use only a home-type system.

Non- Home A or Non- Home B means the phone tries to

use only a non-home-type system.

Home Ar ea means the phone cannot roam at all.

Note: To use this option, your home system operator must

have a roaming agreement with the host company whose

system you try to use. Contact your home system operator

for the roaming agreements they have with other operators.

Depending on the selection either the A or B indicator

(or both) will appear. Neither indicator appears if Home

Area is selected.

Ro a m in g In d ic a to r s in P u b lic Sys te m s

When the phone begins roaming, it beeps, displays

ROAMI NG, and lights the roaming indicator ( ). For a

description of the two states of the roaming indicator, see

“Keys and the Display”, page ii. Some cellular systems can

recognize a roaming phone automatically. In other

systems, you must contact the cellular operator before the

system can recognize the phone. You will need to give

your phone number, your phone’s ESN (electronic serial

number), and how you plan to pay for your calls. There is

usually an additional charge for roaming calls.

Note: The ESN for your cellular phone is printed under the

battery pack on the back of the phone.

M e n u 6 2 , D u a l m o d e Se le c t

You can set the phone to work in AMPS ( Anal og) and/

or TDMA ( Di gi t al ) networks. The network can always

override your setting, however. When the phone is in dual

mode ( Ana. & Di g. ) , the cellular network automatically

selects the right mode. The phone automatically returns to

dualmode ( Ana. & Di g. ) when you switch the phone

off and back on.

M e n u 6 3 , Vo ic e P r iv a c y

You may set this to On or Of f . Voi ce Pr i vacy On

encrypts the voice channel only in networks with digital

service. If you have this feature on and voice privacy be-

comes inactive for any reason the phone displays VOI CE

PRI VACY I NACTI VE and beeps. Check for availability of

this function from your network operator.

Note: Menu items 6 4, 6 5, and 6 6 appear on your

phone’s menu only if you are using the first telephone

number of your phone (see “Menu 8, NAM Selection”

on page 43), you have subscribed to the service from

your network operator, and you have activated the

menu items with Menu 6 7.

M e n u 6 4 , C a ll Fo r w a r d in g

This appears on the menu only if activated with Menu 6 7.

1) ^{Press left}ñ ^{( Menu)}6 4.

2) Press W to forwarding option.

3) ^{Press left}ñ ^{( OK)}.

4) Press W to Act i vat e or Cancel .

5) ^{Press left}ñ ^{( OK)}.

This forwards your calls to the number that is on display

when you select Act i vat e.

For war d Al l Cal l s (Menu 6 4 1) forwards all

incoming calls.

For war d I f Bus y (Menu 6 4 2) forwards calls only

when you are on the phone.

For war d I f Not Ans wer ed (Menu 6 4 3) forwards

calls if you don’t answer.

For war d I f Out of Reach (Menu 6 4 4) forwards

calls if you are out of the serving cellular network.

Cancel Al l For war di ng (Menu 6 4 5) cancels all

currently-active forwarding options.

M e n u 6 5 , C a ll W a itin g

This appears on the menu only if activated with Menu 6 7.

1) ^{Press left}ñ ^{( Menu)}6 5.

2) Press W to Act i vat e or Cancel .

3) ^{Press left}ñ ^{( OK)}.

If you activate call waiting, you will receive a tone during a

call to let you know you have an incoming call. The phone

may also display the incoming caller’s identification.

^{To answer the incoming call, press}í. (The current call

is put on hold.)

M e n u 6 6 , Se n d O w n N u m b e r

This appears on the menu only if activated with Menu 6 7.

1) ^{Press left}ñ ^{( Menu)}6 6.

2) Press W to Yes (to show number) or No (to not show

number).

3) ^{Press left}ñ ^{( OK)}.

4) Key in the number you want to call at Number : prompt.

5) Press

to call.

This specifies whether or not to display (i.e., Send) your phone

number to the person you are calling. Your selection here ap-

plies only to the next call you make. After that it goes back to

the default. Check with your network operator to find out

what the default is.

Note: This feature functions only in systems equipped with

Calling Number Identification. Contact your network operator

to see if this is available.

M e n u 6 7 , N e tw o r k Fe a tu r e Se t tin g

Call Forwarding, Call Waiting, and Send Own Number are

services available through your network operator.

When you subscribe to any of these services, your operator

or dealer gives you a separate code that you use to activate

and deactivate each service.

Menu 6 7 lets you store all the codes you use in your

phone. Once you store the code in your phone, the service

appears as a menu item. You can then use the menu to

activate and deactivate CALL FORWARDI NG, CALL

WAI TI NG, and SEND OWN NUMBER.

To remove an item from the menu, go through the steps

shown in “To Store Codes”, but simply press left

( OK) after the Feature code: prompt (without entering a

code).

^T1)^o^P^s^re^to^ss^{r e}^left^cñ^{o d e}⁽^s^M^:^enu)6 7. This puts you in the

Network Feature Setting Menu.

2) At Feat ur e Code: enter the code you want to

store in your phone (e.g. ∗74) then left ñ ^{( OK)}.

3) Press W until you see CALL FORWARDI NG, CALL

WAI TI NG, or SEND OWN NUMBER. Press left

( OK) to choose the one you want the code to apply to.

With CALL FORWARDI NG, you then choose the

^r^s^e^p^aecch^ifi^y^c^o^t^u^y^r^p^c^e^hoo^f^ic^C^e^A^t^L^h^L^en^F^le^O^ft^Rñ^WARD⁽^I^O^N^K^G⁾^..^{Press W to}

⁴5)⁾^P^P^r^r^e^e^s^s^s^{s Wleftt}ñ^{o rea}⁽^ch^OK^A⁾^c.^{t i vat e or Cancel}

M e n u 7 , S y s t e m S e a r c h

Your phone works in Public Systems (such as your Home

System), and in Private Systems (if supported by the net-

work). With Menu 7, you choose how the phone selects a

network to use. The default is Aut omat i c, which means

the phone automatically searches for networks available to

you and chooses the appropriate one. Every time you

switch on the phone, it resets this to Aut omat i c.

(Note that it chooses which Public system to use based on

the choice you make in Menu 6 1, Public Systems).

If you choose Manual , the phone searches for networks,

then begins displaying them. The phone displays AVAI L-

ABLE: or NOT AVAI L: for the systems it finds. (You

cannot use NOT AVAI L: systems.) Use the W key to

scroll through the choices, and press ( OK) when you see

the one you want.

If you choose New Sear ch, the phone begins a new

search for new Private and Residential systems. When it

finds the best new system, it displays it. You can then

Sel ect it, or start another search by pressing Next .

To s w itc h fr o m p r iv a te t o p u b lic

If you are in a private system and want access to a public

^{system, press and hold left}ñ ^{( Menu)},when you are

not in a call. You can then search through and select avail-

able public systems. The phone uses the public system

you choose for one outgoing call. After that it goes back to

Aut omat i c system selection.

M e n u 8 , N A M S e le c t io n

1) Press left ñ ^{( Menu)}8.

2) Press W to phone number to use.

3) ^{Press left}ñ ^{( Sel ect )}.

The cellular operator programs your phone with software

called a Number Assignment Module (NAM) when you

3 cellular systems, each giving your phone a different

NAM, which contains unique data for you such as your

phone number, home service area, and A-key.

Only one NAM is in effect at a time. When you select a

NAM (phone number), you are also selecting your Home

System. The first phone number displayed with this menu

is the phone number in use.

Note: You need at least one active number to make calls.

You cannot change from one NAM to another during a call.

M e n u 9 , N u m b e r Ed it o r

The number you want to edit must be on the display.

1) ^{Press left}ñ ^{( Menu)}9.

Pressing

removes the digit left of cursor.

Pressing W or V moves the cursor right or left.

Key in new numbers and special characters as you

need them.

2) Press left

number. You can press

^{ñ ( OK) wh}í^{en you’re done editing the}

to dial the edited numbe r .

Your changes aren’t saved unless you save the number!

M e n u 10 , A le r t O p t io n s

With Ri ng & Vi br a the phone rings and vibrates for in-

coming calls. With Ri ng the phone sounds a ringing tone.

With Beep Once the phone sounds a short beep. With

Vi br at e the phone only vibrates. With Si l ent , the

phone only flashes its lights and CALL.

The vibrator function can be activated, but it functions only

if an optional vibrating battery is used (BBT-1XV). Contact

your dealer for more information.

For different ringing volume levels and tone patterns, use

“Menu 3 1, Ringing Volume” on page 32 and “Menu 3 2,

Ringing Tone” on page 32.

When the phone starts to alert, you can press

the ringing tone. The phone continues to alert silently by

to mute

flashing the lights and the text CALL on the display.

When Beep Once, Vi br at e or Si l ent has been

chosen, the phone displays SI LENT. Call related tones

like message received or voice mail indication beeps

become shorter with one of the above options selected.

When Si l ent has been chosen, Automatic Answer

(Menu 3 6) does not work.

If Vi br at e is selected and no vibrating battery is at-

tached, the phone automatically goes into Si l ent mode

for incoming calls. If the phone is set to Vi br at e and

then placed in a Handsfree stand, the phone rings only.

When the phone is connected to a HF desktop charger,

HF car kit, or headset, the alert options can be set

separately for each of these accessories.

M e n u 11, L o c k t h e K e y s

•

Press left ñ ^{( Menu)}then 11.

left

^Theñ^{keys remain locked until you unlock them by pressing}

then ∗. With KEYS LOCKED and no call in

progress, no key tones are heard and no key presses are

accepted, except for calls to 911 (or other official prepro-

^{grammed emergency number),}í, and

When placing an emergency call, the emergency number

is displayed only after you have keyed in all its digits. After

the emergency call, Key Lock automatically becomes ac-

tive again. Keys cannot be locked when the phone is

connected to a car kit or in the handsfree desktop charger.

10 . D a t a a n d F a x C a lls

The phone can send or receive data when it is connected

to a compatible data terminal (such as a fax machine or

PC) through a data adapter. See the documentation for

the data adapter and terminal.

Only analog data can be sent and received.

The phone recognizes the type of the connected terminal

automatically. For instance, if a fax machine is connected

to the phone, the phone makes a fax call.

Note: Pressing and holding 9 to initiate an emergency call

does not work when the phone is connected to a modem.

To s ta r t a n o u t g o in g d a t a o r fa x c a ll

1) Check that the data terminal is properly installed.

A data or fax transmission is always started from the

data terminal.

2) Start the transmission from the data terminal in the

normal way. For example, to send a telefax, start the

transmission from the fax machine’s keypad. The

phone calls the number you dialed from the terminal’s

keypad.

3) After the transmission, end the call from the data

terminal. OR, press

To r e c e iv e a d a t a c a ll

1) Check that the data terminal is properly installed.

2) Press

to answer the call. OR, if you know that the

incoming call is a data call, you can answer the call

from the data terminal.

3) After the transmission, end the call from the data ter-

minal. OR, press

To r e c e iv e a fa x c a ll

1) Check that the data terminal is properly installed.

2) Press

to answer the call. OR, if you know this is

an incoming fax, you can answer the call from the fax

machine’s keypad.

3) After the transmission, end the call from the fax

machine’s keypad. OR, press

11. A c c e s s o r ie s

In addition to the accessories that were included in your

phone’s sales package, you may also find a separate full

color accessories brochure. You can select from a wide

range of Nokia accessories to accommodate your specific

communication needs.

For availability, please check with your local dealer.

A fe w p r a c tic a l r u le s fo r a c c e s s o r y o p e r a tio n

•

Keep all accessories out of the reach of small children.

When you disconnect the power cord of any acces-

sory, grasp and pull the plug, not the cord.

•

Check regularly that all cellular phone equipment in a

vehicle is mounted and operating properly.

Installation of complex car accessories must be made

by qualified personnel only.

Note: Use only batteries, antennas, chargers, and acces-

sories approved by the phone manufacturer. The use of

any other types will invalidate any approval or warranty ap-

plying to the phone, and may be dangerous.

B a t t e r ie s

The following battery options are available for your phone.

Charging times in the table are approximate, using either

the Rapid Travel Charger (ACH-4U) or the Rapid Cigarette

Lighter Charger (LCH-2). Talk times are also approximate.

(BBH-1S) 600 mAh NiMH Slim Battery

(BBT-1XV) 600 mAh NiMH Vibrating Battery

(BBH-1SF) 800 mAh NiMH Extended Slim Battery

(BBH-2H) 1100 mAh NiCd Ultra Extended Battery

(BBH-1H) 1700 mAh NiMH Ultra Extended Battery

Also see “The Battery” on page 3 and “Important Battery

Information” on page 5.

A p p r o x im a t e b a t t e r y o p e r a tio n tim e s

C h a r g in g

Tim e

St a n d b y

Tim e

B a t t e r y

Ta lk Tim e

(Digital)

Up to 1 hr.

10 min.

(Analog)

Up to 45 min.

(ACH-3U/

AEC3518)

270 min.

(ACH-4U)

60 min.

(BBH-1S)

Slim

600 mAh

NiMH

(Digital)

26-30 hrs.

(Analog)

14-19 hrs.

(Digital)

Up to 1 hr.

10 min.

(Analog)

Up to 45 min.

(ACH-3U/

AEC3518))

270 min.

(ACH-4U)

60 min.

(BBT-1XV)

Vibrating

600 mAh

NiMH

(Digital)

26-30 hrs.

(Analog)

14-19 hrs.

(Digital)

Up to 1 hr.

30 min.

(Analog)

Up to 1 hr.

(BBH-1SF) (ACH-3U/

(Digital)

40 hrs.

(Analog)

25 hrs.

Extended

Slim

AEC3518)

270 min.

(ACH-4U)

60 min.

800 mAh

NiMH

(Digital)

Up to 2 hrs.

30 min.

(Analog)

Up to 1 hr.

30 min.

(BBH-2H)

Ultra

Extended

1100 mAh

NiCd

(ACH-3U/

AEC3518))

540 min.

(ACH-4U)

120 min.

(Digital)

52-60 hrs.

(Analog)

28-38 hrs.

(BBH-1H)

Ultra

Extended

1700 mAh

NiMH

(ACH-3U/

AEC3518))

840 min.

(ACH-4U)

150 min.

(Digital)

Up to 3 hrs.

30 min.

(Analog)

Up to 2 hrs.

(Digital)

71-83 hrs.

(Analog)

40-52 hrs.

Note: Battery operation times vary according to signal

conditions, network parameters set by the operator, and

how you use the batteries.

Using the phone near the network’s base station con-

sumes less power. Keeping the antenna fully extended

whenever possible maintains the connection to the net-

work with less power.

CONTAINS: NICKEL METAL HYDRIDE

AND/OR NICKEL CADMIUM BATTERY.

MUST BE RECYCLED OR DISPOSED OF

PROPERLY. MUST NOT BE DISPOSED

OF IN MUNICIPAL WASTE.

NiMH

NiCd

C h a r g e r s

It is recommended that you allow your battery to fully dis-

charge before you recharge it. Batteries last longer and

perform better if allowed to discharge fully at least once a

week.

Sta n d a r d Tr a v e l C h a r g e r (AC H -3 U)

This charger can be used with all

battery options. Note that you can-

not make calls during charging

when the battery is fully discharged.

Plug the charger into a wall outlet

and connect the lead to the base of

the phone or to a light desk stand.

Ra p id Tr a v e l C h a r g e r (AC H -4 U)

This lightweight AC charger can be

used with all battery options. Calls

can be made during charging, even

with a fully discharged battery.

To use the Rapid Travel Charger

(ACH-4U), plug it into a standard

120V AC wall outlet, and connect the

lead from the charger to the base of

the phone.

The charger can also be used together

with the optional Compact Desktop

Charging Stand (CHH-2) and Light Desk

Stand (CHH-2L).

Ra p id C ig a r e tt e L ig h t e r C h a r g e r (L C H -2 )

You can charge the

phone battery from your

vehicle battery by using

the Rapid Cigarette Light-

er Charger (LCH-2). You

can also use the charger

with stands (CHH-2) and

CHH-2L (described be-

low). Calls are possible during charging.

A green light indicates the charger is ready for charging

(when not charging) or finished charging (if it has been

charging). A red light indicates charging. The battery

charging times are the same as those for the Rapid Travel

Charger (ACH-4U).

The input voltage range is from 10 to 30V DC, negative

grounding. Avoid prolonged charging with the Rapid Cig-

arette Lighter Charger (LCH-2) when the car engine is not

running; this may cause the battery of your car to drain.

Note also that in some cars the cigarette lighter plug is not

provided with electricity if the ignition is not switched on.

Fu s e Re p la c e m e n t

The Rapid Cigarette Lighter Charger contains a protective

fuse. The fuse is located in the charger tip. If the charger

does not work, the fuse may be blown, in which case re-

place it with a 3 amp. 125 volt fuse. Never use a fuse with

a higher rating.

C o m p a c t D e s k to p C h a r g in g St a n d

(C H H -2 )

The Compact Desktop Charging

Stand (CHH-2) allows you to

place both the phone and a spare

battery for charging at the same

time in the stand. It is compatible

with all battery options.

The charger starts to charge the spare battery as soon as

it has finished charging the phone battery.

Connect either the Rapid Travel Charger (ACH-4U) or the

Rapid Cigarette Lighter Charger (LCH-2) to the stand, and

then plug the Rapid Travel Charger or Rapid Cigarette

Lighter Charger into a wall outlet or vehicle respectively.

Place the phone and/or the spare battery in the stand.

To discharge the spare battery, press the blue button on

the stand. When the battery is totally discharged, recharg-

ing starts automatically. (If you wish to stop discharging,

press the button again to start the charging right away.)

Only the spare battery can be discharged.

The blinking red light indicates discharging, the continuous

red light indicates recharging and the green light indicates

trickle charging. The phone is ready for use when the

green light appears (check the charge on the phone

display).

L ig h t D e s k St a n d (C H H -2 L )

The Light Desk Stand (CHH-2L)

offers support for the phone

during charging. Used together

with the Standard Travel Charg-

er (ACH-3U), Rapid Travel

Charger (ACH-4U), or the Rapid

Cigarette Lighter Charger

(LCH-2), this drop-in stand is an economical choice when

you need your phone close at hand, always ready for calls.

Charging is indicated by the scrolling battery bars on the

right side of the phone’s display. Charging is finished when

the scrolling stops.

12 . C a r e a n d M a in t e n a n c e

Your phone is a product of superior design and craftsman-

ship and should be treated with care. The suggestions

below will help you to fulfill the warranty obligations and to

enjoy this product for many years.

•

Keep the phone and all its parts and accessories out

of small childrens’ reach.

•

Keep the phone dry. Precipitation, humidity and

liquids contain minerals that will corrode electronic

circuits.

•

Do not use or store the phone in dusty, dirty areas.

Its moving parts can be damaged.

Do not store the phone in hot areas. High tempera-

tures can shorten the life of electronic devices, damage

batteries, and warp or melt certain plastics.

•

Do not store the phone in cold areas. When the

phone warms up (to its normal temperature), moisture

can form inside the phone, which may damage

electronic circuit boards.

•

Do not attempt to open the phone. Non-expert

handling of the phone may damage it.

Do not drop, knock or shake the phone. Rough

handling can break internal circuit boards.

Do not use harsh chemicals, cleaning solvents, or

strong detergents to clean the phone. Wipe it with a

soft cloth slightly dampened in a mild soap-and-water

solution.

•

If the phone or any of its accessories are not working

properly, take them to your nearest qualified service

facility. The personnel there will assist you, and if

necessary, arrange for service.

13 . F o r Yo u r S a f e t y

Tr a f f ic S a f e t y

Do not use a hand-held telephone while driving a vehicle.

If using a hand-held telephone park the vehicle before

conversing.

Always secure the phone in its holder; do not place the

phone on the passenger seat or where it can break loose

in a collision or sudden stop.

The use of an alert device to operate a vehicle’s lights or

horn on public roads is not permitted.

Remember road safety always comes first!

O p e r a t in g En v ir o n m e n t

Remember to follow any special regulations in force in any

area and always switch off your phone whenever it is forbid-

den to use it, or when it may cause interference or danger.

Operation of any radio transmitting equipment, including

cellular telephones, may interfere with the functionality of

inadequately protected medical devices. Consult a physi-

cian or the manufacturer of the medical device if you have

any questions. Other electronic equipment may also be

subject to interference.

As with other mobile radio transmitting equipment, users

are advised that for the satisfactory operation of the equip-

ment and for the safety of personnel, it is recommended

that the equipment should only be used in the normal op-

erating position.

Users are advised to switch off the phone when at a re-

fueling point (service station). Users are reminded of the

need to observe restrictions on the use of radio equipment

in fuel depots (fuel storage and distribution areas), chemical

plants or where blasting operations are in progress.

Do not store or carry flammable liquids, gases or explosive

materials in the same compartments as the phone, its

parts or accessories.

Only qualified personnel should install or service the phone

in a vehicle. Faulty installation or service may be danger-

ous and may invalidate the warranty.

Electronic fuel injection systems, electronic anti-skid braking

systems, electronic cruise control systems and other

electronic systems can malfunction due to the lack of pro-

tection from radio signals. Check regularly that all cellular

phone equipment in a vehicle is mounted and operating

properly.

Switch off your cellular phone when in an aircraft. The use

of cellular telephones in an aircraft may be dangerous to

the operation of the aircraft, disrupt the cellular network,

and is illegal.

Failure to observe these instructions may lead to suspen-

sion or denial of cellular telephone services to the offender,

or legal action or both.

Em e r g e n c y C a lls

IM P O RTA N T!

This phone, like any cellular telephone, operates using radio

signals, cellular and landline networks, and user-pro-

grammed functions which cannot guarantee connection in all

conditions. Therefore you should never rely solely upon any

cellular phone for essential communications (e.g. medical

emergencies).

Remember, to make or receive any calls this phone must

be switched on and in a service area with adequate cellular

signal strength.

Emergency calls may not be possible on all cellular net-

works or when certain network services and/or phone

features are in use. Check with local service providers.

Em e r g e n c y c a lls o n yo u r p h o n e

If certain features are in use (Keyguard, Locking, Call Re-

stricting, etc.), you may first need to turn those features off

before you can make an emergency call. Consult this doc-

ument and your local cellular service provider. When

making an emergency call, remember to give all the nec-

essary information as accurately as possible. Remember

that your cellular phone may be the only means of commu-

nication at the scene of an accident - do not cut off the call

until given permission to do so.

Em e r g e n c y c a llin g

1) If the phone is not on, switch it on.

2) Press and hold

to clear display.

3) Key in emergency number for your present location

(e.g. 911 or other official emergency number).

4) Press

IM P O RTA N T!

Use only batteries, antennas, chargers, and accessories

approved by the phone manufacturer. The use of any other

types will invalidate any approval or warranty applying to

the telephone, and may be dangerous.

14 . Te c h n ic a l D a t a

Cellular System

Weight

TDMA and AMPS

7.9 oz (224g) with 600mAh

NiMH battery

Capacity

169 cc

Frequency Range

824.010 - 848.970 MHz (TX)

869.010 - 893.970 MHz (RX)

Transmitter Output

Power

0.4mW to 600mW nominal

Battery Voltage

6 V nominal

Charging Current

800mA typical

Operating Temperature -20° C to + 40° C

(-4° F to + 104° F)

Number of Channels 832

Number of NAMs

Memory Locations

Memory Capacity

100

Alpha: 16 digits per location

Numeric: 16 digits per location

+ 30 digits in 8 locations.

Nokia is a registered trademark of Nokia Corporation.

The information contained in this User Guide was written for dual-mode phone

NHC-4NE/HE.

The right to make changes and improvements to any of the products

described in this guide without prior notice is reserved.

These commodities are authorized by the U.S. Government for export only to

Canada, Mexico, or the United States. They may not be resold, diverted,

transferred, transshipped or otherwise disposed of in any other country, either

in their original form or after being incorporated through an intermediate pro-

cess into other end-items, without the written approval of the U.S. Department

of State.

09/97

Printed in Canada

NOKIA One-Year Limited Warranty

Nokia Mobile Phones, Inc. (“NMPI”) warrants that this cellular

phone (“Product") is free from defects in material and workman-

ship, according to the following terms and conditions:

1. The limited warranty for the Product extends for ONE (1) year

beginning on the date of purchase of the Product.

2. The limited warranty extends only to the original consumer

purchaser (“Consumer”) of the Product and is not assignable or

transferable to any subsequent purchaser/end user.

3. The limited warranty extends only to Consumers who pur-

chase the Product in the United States.

4. During the limited warranty period, NMPI will repair, or replace,

at NMPI’s option, any defective parts, or any parts that will not

properly operate for their intended use with new or factory rebuilt

replacement items. No charge will be made to the Consumer for

any such parts. NMPI will also pay for the labor charges incurred

by NMPI in repairing or replacing the defective parts. The external

housing and cosmetic parts shall be free of defects at the time of

shipment and, therefore, shall not be covered under these limited

warranty terms.

5. Upon request from NMPI, the Consumer must provide infor-

mation to reasonably prove the date of purchase.

6. The Consumer shall bear the cost of shipping the Product to

the Customer Service Department of NMPI. NMPI shall bear the

cost of shipping the Product back to the Consumer after the

completion of service under this limited warranty.

7. The Consumer shall have no coverage or benefits under this

limited warranty if any of the following conditions are applicable:

a) The Product has been subject to abnormal use, abnormal

conditions, improper storage, exposure to moisture or dampness,

unauthorized modifications, unauthorized connections, unauth-

orized repair, misuse, neglect, abuse, accident, alteration,

improper installation, or other acts which are not the fault of NMPI,

including damage caused by shipping and blown fuses.

b) The Customer Service Department at NMPI was not notified by

Consumer of the alleged defect or malfunction of the Product

during the applicable limited warranty period.

c) The Product serial number plate or the accessory date code

has been removed, defaced, or altered.

d) The defect or damage was caused by the defective function of

the cellular system, or by inadequate signal reception by the

external antenna.

8. If a problem develops during the limited warranty period, the

Consumer should take the following step-by-step procedure:

a) The Consumer shall return the Product to the place of

purchase for repair or replacement processing.

b) If “a” is not convenient the Consumer may contact the

Customer Service Department at NMPI, at the phone number

listed on the bottom of the following page for further instructions.

c) The Consumer shall ship the Product prepaid and insured.

Expenses related to removing the Product from an installation are

not covered under this limited warranty.

d) The Consumer will be billed for any parts or labor charges not

covered by this limited warranty. The Consumer shall be

responsible for expenses related to reinstallation of the Product.

e) If the Product is returned to the Customer Service Department

at NMPI during the limited warranty period, but the problem with

the Product cannot be fixed under the terms and conditions of this

limited warranty, the Consumer will be notified and given an

estimate of the charges the Consumer must pay to have the

Product repaired, with all shipping charges billed to the Consumer.

If the estimate is refused, the Product will be returned freight

collect. If the Product is returned to the Customer Service

Department at NMPI after the expiration of the warranty period,

NMPI’s normal service policies shall apply and the Consumer will

be invoiced for all shipping charges.

9. The Product consists of newly assembled equipment that may

contain used components which have been reprocessed to allow

machine compliance with Product performance and reliability

specifications.

10. ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FIT-

NESS FOR A PARTICULAR PURPOSE OF USE, SHALL BE

LIMITED TO THE DURATION OF THE FOREGOING WRITTEN

WARRANTY, OTHERWISE, THE FOREGOING WARRANTY IS THE

PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND IN LIEU

OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. NMPI

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES OR A LOSS OF ANTICIPATED BENEFITS OR PROFITS,

RESULTING FROM THE PURCHASE OR USE OF THE PRODUCT

OR ARISING FROM THE BREACH OF THE WARRANTY EVEN IF

NMPI KNEW OF THE LIKELIHOOD OF SUCH DAMAGES.

11. Some states do not allow limitation of how long an implied

warranty lasts, so the above limitation may not apply to you (the

Consumer). Some states do not allow the exclusion of incidental or

consequential damages, so the above limitation or exclusions may

not apply to you (the Consumer). This limited warranty gives you

specific legal rights and you may also have other rights which vary

from state to state.

12. NMPI neither assumes nor authorizes any authorized service

center or any person or entity to assume for it any other obligation

or liability beyond that which is expressly provided for in this limited

warranty.

13. Questions concerning this limited warranty may be directed

to the Customer Service Department at Nokia, 6200 Courtney

Campbell Causeway, Suite 900, Tampa, FL 33630. Telephone

(813) 288-3800 or 1-800-666-5553, Facsimile: (813) 287-6612.

14. The limited warranty period for Nokia Product Corp. supplied

attachments and accessories are specifically defined within their

own warranty cards and packaging.

NOTES

Nikon MOTO QA4 User Manual
NAD C 521BEE User Manual
Motorola MOTORAZR2 68002425001 User Manual
Motorola CLIQ TM1668 User Manual
Melitta ME2TMDS User Manual
Maxtor MaxAttach NAS 4100 User Manual
LG Electronics TD7130 User Manual
Kenwood KDC 2024S User Manual
Audiovox VOX 8610 User Manual
Alpine CDA 7873R User Manual