Motorola StarTAC 85 User Manual

Cellular  
Telephone  
Owners  
Manual  
TABLE OF CONTENTS  
GENERAL SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . 6  
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
PHONE OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Preparing Battery for Initial Use. . . . . . . . . . . . . . . . . . . . . 12  
Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Quick Change Method . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Turn Phone On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Placing a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Automatic Redialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Call in Absence Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Signal Strength Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Displaying Battery Voltage Meter. . . . . . . . . . . . . . . . . . . . 19  
Low Battery Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Adjusting Earpiece Volume . . . . . . . . . . . . . . . . . . . . . . . . 20  
Adjusting Ringer Volume. . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Volume Meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Muting Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Displaying Own Phone Number . . . . . . . . . . . . . . . . . . . . 20  
Two-System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Illuminated Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Antenna System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Storing Numbers to a Memory Location. . . . . . . . . . . . . . . 22  
Memory Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Changing Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
3
TABLE OF CONTENTS  
Clearing Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Recalling from Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Memory Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Recalling Last Number Called . . . . . . . . . . . . . . . . . . . . . . 24  
Recalling Area Code / Prefix (Postscripting) . . . . . . . . . . . . 24  
Turbo Dial™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
One-Touch Emergency Dialing . . . . . . . . . . . . . . . . . . . . . 25  
Super Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Scratch Pad Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Tone Dialing (Two-Part Calling) . . . . . . . . . . . . . . . . . . . . . 26  
Pause Dialing (Memory Linking) . . . . . . . . . . . . . . . . . . . . 26  
Placing a Linked Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
To Enable/Disable a Specific Feature . . . . . . . . . . . . . . . . . 29  
Distinctive Ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Automatic Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Multiple Key Answer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Automatic Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
One-Touch Emergency Dialing . . . . . . . . . . . . . . . . . . . . . 32  
VOX Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Reminder Beeps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
PIN Code Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Feature Status Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
TIMERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Individual Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Resettable Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Cumulative Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
One Minute Beep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
4
TABLE OF CONTENTS  
SECURITY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Electronic Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Displaying Unlock Code . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Changing Unlock Code. . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Automatic Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Outgoing Call Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . 38  
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Chargers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Ultra Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Travel Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . . . . . . 44  
ROAMING AND SYSTEM OPERATION. . . . . . . . . . . . . . . 47  
Service Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Weak Signal Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Roaming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Selectable System Registration. . . . . . . . . . . . . . . . . . . . . . 48  
Changing System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
C Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
BEFORE CALLING FOR SERVICE . . . . . . . . . . . . . . . . . . . 51  
MESSAGE GLOSSARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
PATENT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . 60  
QUICK REFERENCE SECTION. . . . . . . . . . . . . . . . . . . . . . 61  
5
GENERAL SAFETY INFORMATION  
IMPORTANT  
Read This Information Before Using Your  
Hand-held Portable Cellular Telephone  
First introduced in 1984, the hand-held portable cellular telephone  
is one of the most exciting and innovative electronic products ever  
developed. With it, you can stay in contact with your office, your  
home, emergency services, and others.  
For the safe and efficient operation of your phone, observe  
these guidelines.  
Your cellular telephone is a radio transmitter and receiver. When it  
is ON, it receives and also sends out radio frequency (RF) energy.  
The phone operates in the frequency range of 824 MHz to 894  
MHz and employs commonly used frequency modulation (FM)  
techniques. When you use your phone, the cellular system  
handling your call controls the power level at which your phone  
transmits. The power level can range from 0.006 of a watt to 0.6  
of a watt.  
Exposure to Radio Frequency Energy  
In 1991, the Institute of Electrical and Electronics Engineers (IEEE),  
and in 1992, the American National Standards Institute (ANSI),  
updated the 1982 ANSI Standard for safety levels with respect to  
human exposure in RF energy. Over 120 scientists, engineers, and  
physicians from universities, government health agencies, and  
industry, after reviewing the available body of research, developed  
this updated Standard. In March 1993, the Federal  
Communications Commission (FCC) proposed the adoption of this  
updated Standard.  
The design of your phone complies with this updated Standard. If  
you want to limit RF exposure even further, you may choose to con-  
trol the duration of your calls and operate your phone in the most  
power efficient manner.  
Efficient Phone Operation  
For your phone to operate at the lowest power level consistent with  
satisfactory call quality. Please observe the following guidelines.  
If your phone has an extendable antenna, extend it fully. Some  
models allow you to place a call with the antenna retracted.  
However, your phone operates more efficiently with the antenna  
fully extended.  
Hold the phone as you would any other telephone. While speak-  
ing directly into the mouthpiece, position the antenna up and over  
your shoulder.  
6
GENERAL SAFETY INFORMATION  
Do not hold the antenna when the phone is in use. Holding the  
antenna affects call quality and may cause the phone to operate at  
a higher power level than needed.  
Antenna Care and Replacement  
Do not use the phone with a damaged antenna. If a damaged  
antenna comes into contact with the skin a minor burn may result.  
Replace a damaged antenna immediately. Take your phone to a  
qualified service center for repair.  
Use only the supplied or approved antenna. Non-approved anten-  
nas, modifications, or attachments could impair call quality, dam-  
age the phone and violate FCC regulations.  
Driving  
Check the laws and regulations on the use of cellular telephones in  
the areas where you drive. Always obey them. Also, when using  
your phone while driving, please:  
• Give full attention to driving,  
• Use hands-free operation, if available, and  
• Pull off the road and park before making or answering a call if  
driving conditions so require.  
Electronic Devices  
Most modern electric equipment—for example equipment in hos-  
pitals and cars—is shielded from RF energy. However, RF energy  
from cellular telephones may affect malfunctioning or improperly  
shielded electronic equipment.  
RF energy may affect improperly installed or inadequately shielded  
electronic operating and entertainment systems in motor vehicles.  
Check with the manufacturer or its representative to determine if  
these systems are adequately shielded from external RF energy. You  
should also check with the manufacturer of any equipment that has  
been added to your vehicle.  
Consult the manufacturer of any personal medical devices (such as  
pacemakers, hearing aids, etc.) to determine if they are adequately  
shielded from external RF energy.  
Turn your phone OFF in health care facilities when any regulations  
posted in the areas instruct you to do so. Hospitals or health care  
facilities may be using remote RF monitoring equipment.  
Aircraft  
Turn your phone OFF before boarding any aircraft.  
• Use it on the ground only with crew permission.  
• Do not use in the air.  
7
GENERAL SAFETY INFORMATION  
To prevent possible interference with aircraft systems, Federal  
Aviation Administration (FAA) regulations require you to have per-  
mission from a crew member to use your phone while the plane is  
on the ground. To prevent interference with cellular systems, FCC  
regulations prohibit using your phone while the plane is in the air.  
Children  
Do not allow children to play with your phone. It is not a toy.  
Children could hurt themselves or others (by poking themselves or  
others in the eye with the antenna, for example). Children also  
could damage the phone, or make calls that increase your tele-  
phone bills.  
Blasting Areas  
To avoid interfering with blasting operations, turn your unit OFF  
when in a blasting area or in areas posted: Turn off two-way  
radio. Construction crews often use remote control RF devices to  
set off explosives.  
Potentially Explosive Atmospheres  
Turn your phone OFF when in any area with a potentially explosive  
atmosphere. It is rare, but your phone or its accessories could gener-  
ate sparks. Sparks in such areas could cause an explosion or fire  
resulting in bodily injury or even death.  
Areas with a potentially explosive atmosphere are often, but not  
always, clearly marked. They include: fueling areas such as gas sta-  
tions, below deck on boats, fuel or chemical transfer or storage facil-  
ities, and areas where the air contains chemicals or particles, such as  
grain, dust, or metal powders, and any other areas where you would  
normally be advised to turn off your vehicle engine.  
Do not transport or store flammable gas, liquid, or explosives in the com-  
partment of your vehicle which contains your phone or accessories.  
Vehicles powered by liquefied petroleum gas (such as propane or  
butane) must comply with the National Fire Protection Standard  
(NFPA-58). For a copy of this standard, contact the National Fire  
Protection Association, One Batterymarch Park, Quincy, MA 02269,  
Attn: Publications Sales Division.  
Magnetic Storage Media  
Your phone contains a magnet. Do not place your phone in close  
proximity to magnetic storage media such as diskettes or credit cards  
for extended periods of time.  
Batteries  
CAUTION: To prevent injuries or burns, do not allow metal objects  
to contact or short circuit the battery terminals.  
8
GENERAL SAFETY INFORMATION  
The design of Motorola’s cellular telephone complies with all applic-  
able RF Safety Standards.  
Motorola meets the standards and recommendations for the protec-  
tion of public exposure to RF electromagnetic energy established by  
governmental bodies and other qualified organizations, such as the  
following:  
• National Council on Radiation Protection and Measurements  
(NCRP). Report 86.  
• Department of Health and Welfare Canada Safety Code 6.  
• Verband Deutscher Elektroigenieure (VDE) DIN-0848.  
• Directives of the European Community, Directorate General V in  
Matters of Radio Frequency Electromagnetic Energy.  
• National Radiological Protection Board of the United Kingdom.  
GS-11, 1988.  
• American National Standards Institute (ANSI)/IEEE  
C95.1-1992.2.  
INTRODUCTION  
This phone represents the state-of-the-art in personal cellular tele-  
phones today. The listing below shows just a few of the exceptional  
features that this telephone contains:  
• Signal Strength Meter  
• Battery Meter  
Turbo Dialing  
• Auto Answer  
• Call Timers  
• One-Touch Emergency Dialing  
• 9 Selectable Ringer Styles  
• Multiple Key Answer  
• Memory Protect  
Remember, these are just a few of the great features that your phone  
provides to meet your business and personal needs. In addition, a num-  
ber of accessory options are available to help you tailor your cellular  
system to your individual preferences. These include a 3-Watt Booster  
or an Ultra Saver that plugs into the vehicle’s cigarette lighter to con-  
serve the telephone’s battery.  
To help you become familiar with your telephones features, we suggest  
you experiment with them as you progress through this manual.  
Please read the General Safety Information beginning on page 6 before  
operating the unit.  
9
1
2
3
4
888  
8888888  
5
6
7
5
8
10  
PHONE OVERVIEW  
1 Retractable Antenna — Extend for optimum performance.  
2 Earpiece  
3 Status Indicators — Flash or light steadily to alert you to a  
number of conditions:  
IU (In Use) — Flashes while a call is in process.  
RM (Roam) — Flashes if phone is accessing a service area out-  
side of your home system.  
NS (No Service) — Flashes or lights steadily if the phone is  
beyond the range of a cellular system. While lit, calls cannot  
be placed or received (See Service Area, page 47).  
Signal Strength Indicator — Flashes the relative strength of the  
signal received by the phone.  
Battery Strength Indicator — Lights steadily to indicate the  
estimated remaining capacity of the battery (See Displaying  
Battery Voltage Meter, page 19).  
4 Number Display — Displays phone number, memory location  
number , or message. Some information will require viewing  
sequentially displayed messages.  
5 Function Keys  
Recalls and displays numbers stored in memory.  
Ø Stores numbers in memory.  
Ç Clears digits from the display. Press and hold to clear  
entire display at once.  
Ï Used in conjunction with other keys to access special  
features.  
Í
´
Places or answers a call.  
Ends a call or exits special functions.  
Turns the phone on or off.  
≥ and ≤ Adjust earpiece and ringer volume.  
6 Numeric Keypad — Enters call information or programs features.  
7 Headset Jack — For handsfree use with optional headset  
accessory.  
8 Mouthpiece  
11  
GETTING STARTED  
P r e p a r i n g B a t t e r y f o r I n i t i a l U s e  
The Nickel-Cadmium or Nickel Metal Hydride Battery supplied with  
your telephone must be fully charged before placing your phone into  
service. The batteries are shipped from the factory in a discharged  
state in order to extend the life of the battery. It is recommended that  
you charge new batteries overnight, but not longer than 24 hours,  
using a Motorola-approved charger.  
WARNING: Battery may explode if exposed to fire. Charging your  
battery in anything other than a Motorola charger will void  
your warranty.  
CAUTION: To prevent injuries or burns, do not allow metal objects  
to contact or short circuit the battery terminals.  
12  
GETTING STARTED  
A t t a c h i n g t h e B a t t e r y  
1. Place the battery pack on the phone so that its grooves align.  
Align the top of the battery with the line on the back of the  
phone right below the arrows.  
2. Slide upward in the direction of the arrows on the back of the  
phone until it clicks into place.  
Battery Attachment  
R e m o v i n g t h e B a t t e r y  
1. Turn your telephone off.  
2. Depress the latch button on the rear of the battery and slide  
the battery pack downward until it stops.  
3. Lift the battery off.  
Battery Removal  
13  
GETTING STARTED  
Q u i c k C h a n g e M e t h o d  
The Quick Change Method allows you to remove your telephone  
battery at any time and replace it with a charged spare battery dur-  
ing a telephone call.  
This is especially useful if you receive the Lo BAT(low battery)  
message or audible tone during a call. Simply remove the battery  
from the telephone, put on the spare battery, and press . This  
will return you to your telephone call. The phone will not go  
through the normal power-up cycle described on page 15. You will  
only have 4 seconds to complete this action before your telephone  
call is terminated. It is a good idea to practice this procedure a few  
times before using it on an actual phone call. Advise the party on  
the other end of the call before beginning this procedure.  
14  
BASIC OPERATION  
T u r n P h o n e O n  
1. Extend antenna for optimal performance.  
2. Press once.  
3. Check the status indicators and display messages before plac-  
ing a call.  
No Service Indicator  
Roam Indicator  
In Use Indicator  
888  
8888888  
Start-up Self Tests  
Each time the telephone is turned on, it performs a series of self  
tests, sounds a tone, and lights all display positions and status indi-  
cators to check their operation. The signal strength meter and bat-  
tery strength meter then display and the keypad lights momentarily,  
as it will any time a key is pressed.  
Message  
Explanation  
•If your phone is programmed for two cel-  
lular systems, one of these messages will  
appear in the display upon power up.  
A1  
A2  
•These are reminders as to which system  
and phone number are currently  
in use.  
B1  
B2  
•Indicates that the phone has been locked  
and cannot send or receive calls until  
unlocked.  
Loc/D  
15  
BASIC OPERATION  
Status Indicators  
Indicators  
Explanation  
IU (In Use Indicator)  
•Flashes when call is in progress.  
888  
8888888  
NS (No Service Indicator)  
•Flashes or lights steadily if phone  
is beyond range of  
service area.  
a
cellular  
888  
•Calls cannot be placed or  
received while NS is lit.  
8888888  
RM (Roam Indicator)  
•If slow or rapid flashing, you are  
accessing a service area outside  
of your home system.  
Slow Flashing  
888  
8888888  
Roaming on a home  
type system.  
Rapid Flashing  
Roaming on a non-home  
type system.  
If no key is pressed within 8 seconds:  
•The keypad backlight will extinguish to conserve the battery level.  
•The signal strength meter will continue to flash indicating that the  
power is still on.  
16  
BASIC OPERATION  
P l a c i n g  
a
C a l l  
1. With the power on, enter the number you wish to call.  
2. Press Í.  
3. Begin the conversation when the called party answers.  
4. To terminate the call, press ´.  
To Correct an Error  
To clear the last digit entered, press and quickly release Ç. To  
clear the entire entry, press and hold Ç until the entire entry  
is erased.  
If Entering More Than 10 Digits  
You can call a phone number with up to 16 digits, but only the  
last 10 digits will appear in the display.  
When recalling a stored phone number that is longer than 10 dig-  
its, the display will flash the memory location number and the last  
10 digits of the number. Press again to view entire number.  
Unsuccessful Call Attempts  
If you hear one of the following signals, you have not successfully  
completed your call.  
Tone / Message Description  
Cellular System Busy  
fast busy  
Press Í again before ending the unsuccessful  
(reorder signal) call attempt to automatically redial the call  
SND TO  
(refer to Automatic Redialing page 18), or press  
REDIAL  
´ and dial the call again.  
Cellular System Could Not Complete the Call  
alternating  
high/low tone  
(intercept)  
SND TO  
You may have tried to place a call before the  
NS (No Service) indicator stops flashing to let  
you know your phone was fully operative.  
Either press Í again before ending the  
unsuccessful call attempt to automatically redial  
the call (refer to Automatic Redialing page 18),  
or press ´ and dial the call again.  
REDIAL  
busy signal  
The called party’s line is busy.  
17  
BASIC OPERATION  
A u t o m a t i c R e d i a l i n g  
Your telephone includes a convenient feature designed to make  
repetitive call attempts automatically when a cellular system  
is busy.  
If you receive an alternating high/low signal (intercept) or the fast  
busy tone (reorder signal) when attempting to place a call and wish  
to retry the call, press Í before ending the unsuccessful call  
attempt. REDIAL is then displayed.  
Your telephone will make the call attempt continuously over the  
next 4 minutes. Once a connection is made, the phone will ring  
once to alert you so that you may lift the phone to your ear and  
begin the conversation.  
If the call cannot be completed within 4 minutes, press Í to  
begin another cycle.  
R e c e i v i n g  
a
C a l l  
1. Press Í.  
NOTE: Pressing Í may activate call transfer or other optional  
system features. Contact your Cellular System Provider for more  
information.  
C a l l i n A b s e n c e I n d i c a t o r  
If your phone is on and an incoming call is unanswered, CALL is  
displayed for 8 seconds. The display and keypad backlight will  
extinguish to conserve the battery level. Pressing any key but Ç  
or ´ redisplays CALL to inform you of the call attempt. You must  
press Ç or ´ to cancel the message and clear the display.  
NOTE: Phone will not display or retrieve the phone number of the  
calling party.  
S i g n a l S t r e n g t h M e t e r  
The Signal Strength Meter (SSM) represents the relative strength of  
the signal received by your phone. The SSM is displayed as shown.  
The alone represents the lowest strength with each additional  
representing a stronger signal.  
18  
BASIC OPERATION  
888  
888  
8888888 8888888  
Weak Signal  
Strong Signal  
The SSM appears every time you turn your phone on. After 8  
seconds, the SSM will continuously flash the relative strength of the  
signal received by the phone.  
To best utilize the SSM, you should familiarize yourself with the rel-  
ative Signal Strength levels and their associated Call Placement and  
Call-in-Progress qualities.  
D i s p l a y i n g B a t t e r y V o l t a g e M e t e r  
1. Press Ï, .  
The Battery Voltage Meter (BVM) represents the current voltage  
level of the battery being used. You can use this to estimate the  
amount of battery capacity remaining. The BVM is displayed as a  
battery bar graph at the left side of the display.  
Low Battery  
Charged Battery  
Variables such as temperature, battery age, and charging conditions  
may affect battery voltage. To help remember which key to use,  
note that battappears on the key.  
L o w B a t t e r y W a r n i n g  
Low battery power is indicated by a short dual tone repeated peri-  
odically, and the displayed message LoBAT. If the message is  
ignored, the phone will automatically turn itself off as the battery  
approaches discharge.  
19  
BASIC OPERATION  
A d j u s t i n g E a r p i e c e V o l u m e  
Press and hold or to raise or lower the earpiece volume  
level.  
A d j u s t i n g R i n g e r V o l u m e  
1. Press Ï.  
2. Press and hold or to raise or lower ringer volume level.  
V o l u m e M e t e r  
The Volume Meter represents the current volume setting and will  
appear in the display whenever you adjust the earpiece or the  
ringer volume.  
v
v=  
Highest Volume  
Lowest Volume  
The volume level is displayed as a bar graph following the letter v  
at the left side of the display. The v alone represents the lowest vol-  
ume setting with each additional bar representing  
volume setting.  
a
higher  
M u t i n g M i c r o p h o n e  
1. While in a call, press Ï, .  
This feature allows you to confer privately with others during a con-  
versation. If you press Ï, during a call, the phone will dis-  
play MUTE. To reinstate the microphone, press Ï, again.  
The mute feature is canceled when you end your call. To help you  
remember which key to use, note that muteappears  
on the key.  
D i s p l a y i n g O w n P h o n e N u m b e r  
1. Press , £.  
2. The phone number that is currently active will be displayed.  
3. When you have finished viewing, press Ç.  
20  
BASIC OPERATION  
T w o - S y s t e m O p e r a t i o n  
Your telephone can operate over two different home systems if you  
have made proper arrangements with your Cellular System  
Operator. Both are designated as your home systembut are  
accessed with separate telephone numbers.  
While you may switch from one system to the other, only one of  
the two can be active at any given time. Calls are placed and  
received through the active system only.  
Switching to a Second Phone Number  
1. Press , £, Ø.  
2. The display will blank to confirm the switch and the newly  
activated number will appear.  
3. When you have finished viewing, press Ç.  
If you have two phone numbers programmed into your phone,  
each time the telephone is turned on, it displays a message indi-  
cating which System Type and phone number is currently active.  
The message shows the System Type and phone number applied,  
as follows:  
System Type and Phone Number  
Display  
A1  
Non-wireline type with phone number 1  
Non-wireline type with phone number 2  
Wireline type with phone number 1  
Wireline type with phone number 2  
A2  
B1  
B2  
If a call is placed to the inactive phone number, the caller will receive the  
recorded Not in Servicemessage.  
I l l u m i n a t e d K e y p a d  
Your keypad lights whenever the phone is turned on, or a call is  
received. To help conserve battery power, the keypad lighting turns  
off if no key is pressed. The display and keypad backlight remain lit  
during menu use.  
21  
BASIC OPERATION  
A n t e n n a S y s t e m  
The Antenna System of your telephone is designed for optimum  
performance with the antenna extended.  
There are two parts to the antenna, one internal and one retractable.  
This allows you to receive calls on your telephone without having  
the antenna extended. If NS (No Service) flashes or lights steadily,  
you may be calling from a fringe coverage area. It will be necessary  
to fully extend the antenna for optimum performance.  
MEMORY  
Your telephone provides 20 numeric memories in which to store  
frequently called phone numbers. The memory will accept entries  
designated by location numbers 01, 02, etc. Calls are placed from  
within the memory by pressing Í when the number is displayed.  
The telephone accepts up to 16 digits for each memory location.  
Before setting up your memory, we suggest that you read the rest of  
this section to become familiar with the ways in which you will  
access and use it.  
S t o r i n g N u m b e r s t o  
a
M e m o r y L o c a t i o n  
1. Enter the number you wish to save, up to 16 digits.  
2. Press Ø.  
3. Enter the two-digit location number (01, 02, etc.) in which  
you choose to place the entry. The location entered is dis-  
played to confirm storage.  
You must enter the location number within 8 seconds of pressing  
Ø or the operation will cancel. If FULL displays refer to Memory  
Protect, see below.  
M e m o r y P r o t e c t  
The directory has an automatic Memory Protect feature which pre-  
vents the accidental overwriting and loss of previously stored num-  
bers in memory. If you attempt to store an entry to a currently  
occupied memory location, the location number and FULL will  
display. The display will then alternate between the previously  
stored number and CHANGE?.  
22  
MEMORY  
If you wish to save to that location, thus overwriting and erasing the  
old information, press Ø.  
If you wish to store the entry in an alternate location, press ´,  
Ø and the alternate location number.  
C h a n g i n g E n t r i e s  
1. Press and the two-digit location number so that the num-  
ber to be changed is displayed.  
2. Press and release Ç to back out each of the digits dis-  
played.  
3. Enter the new number.  
4. Press Ø and the two-digit location. The location number  
and FULL will display. The display will then alternate  
between the previously stored number and CHANGE?.  
5. Press Ø to save the new information to this location.  
C l e a r i n g E n t r i e s  
1. Press and hold Ç.  
2. Press Ø.  
3. Enter the two-digit location number to be cleared.  
The display will alternate between the previously stored  
number and CHANGE?.  
4. Press Ø to clear the memory location.  
R e c a l l i n g F r o m M e m o r y  
1. Press .  
2. Enter the two-digit location number (01, 02, etc.) The display  
shows the location number, then the last 10 digits of its number.  
3. Press to review the complete number.  
M e m o r y S c r o l l i n g  
Memory Scrolling allows you to review your memory locations  
sequentially, beginning with the location of your choice. This is  
23  
MEMORY  
useful when searching for a specific number in memory when you  
are not certain of its location.  
1. Press , then the memory location where you wish to begin  
your review. The location number and digits stored will appear  
in the display. The appearance of an apostrophe (/) following  
the location number confirms that you have enabled  
memory scrolling.  
2. Press £ to scroll forward through the items.  
3. Press to scroll backwards.  
NOTE: and may also be used to scroll forward and backward,  
respectively.  
At any time while scrolling, you may place a call to the displayed  
number by pressing Í.  
NOTE: Memory Scrolling can be performed during a call. Pressing  
´ while scrolling during a call extinguishes the apostrophe (/)  
and cancels scrolling, but does not terminate the call.  
R e c a l l i n g L a s t N u m b e r C a l l e d  
1. Press , , , the display will show the last number  
called.  
2. To place a call to this number, press Í.  
R e c a l l i n g A r e a C o d e / P r e f i x ( P o s t s c r i p t i n g )  
You can add additional digits to the end of recalled numbers by  
entering them before pressing Í. This is particularly useful if you  
often place calls to the same area code and prefix.  
1. Recall two-digit location number where an area code and pre-  
fix is stored.  
2. Add additional digits as needed.  
3. Press Í.  
T u r b o D i a l ™  
Turbo Dial is the fastest method of dialing. The digit keys ¤  
through · provide an advanced form of Super Speed Dialing.  
24  
MEMORY  
1. Press and hold digit keys until the IU (In Use) indicator lights.  
This indicates that the call has been initiated.  
Once numbers have been stored in Memory Locations 02 through  
09, calls can be placed from these locations by pressing and hold-  
ing the associated key for approximately 1 second. There is no  
need to press Í. (01 is reserved for Emergency Dialing).  
O n e - T o u c h E m e r g e n c y D i a l i n g  
1. Press and hold until EMRGCY displays.  
Memory Location 01 may be used for 911 or any other emergency  
number you may wish to dial, even if your phone is locked.  
NOTE: Automatic Redial does not work with Emergency Dialing  
when the phone is locked.  
If your phone is locked and your three-digit unlock code ends with  
the digit 1, the phone will unlock but will not place a 911 call, even  
if you press and hold when unlocking your phone. If you are  
unlocking your telephone and the first or second digit of your three-  
digit unlock code is 1, and you press and hold , you will place  
an emergency call.  
If you do not wish to have EMRGCY appear in the display, this can  
be deactivated by using the Feature Menu found on page 29.  
S u p e r S p e e d D i a l i n g  
Super Speed Dialing is a fast method of placing calls from  
the memory.  
Once information is stored in a memory location, Super Speed  
Dialing allows you to place a call without pressing .  
1. Enter the location number.  
2. Press Í. The number will not appear in the display  
for review.  
NOTE: Attempting the sequence , Í will place a call to  
the operator.  
S c r a t c h P a d M e m o r y  
The Scratch Pad permits entry of numbers from the keypad during  
conversation.  
25  
MEMORY  
If your party gives you another number to call, simply enter it from  
the keypad. If you make an error, press Ç to erase the last digit  
entered or hold Ç to erase the entire entry.  
Advise your party that they will hear tones as you store the num-  
ber. To call the Scratch Pad number at the end of an outgoing con-  
versation, press ´, Í.  
T o n e D i a l i n g ( T w o - P a r t C a l l i n g )  
Your telephone provides the standard Dual Tone Multi-Frequency  
(DTMF) signals used to access alternate long distance services, sig-  
nal pagers, answering machines, etc. Generally, these services use a  
two-part procedure: First, a call is placed from the memory or  
through the keypad to a central telephone number, then a second  
dial tone is heard and the additional tone digits are sent.  
To Tone Dial from the keypad, make the initial call. Append addi-  
tional tone digits using the keypad. The tones are automatically sent  
as you press the keys. Do not press Í.  
To Tone Dial from a memory location, place the initial call. Recall  
from memory (using , two-digit location number) the number  
you wish to send as DTMF digits. Press , Í. Repeat these  
steps as required to send separate groups of numbers.  
Memory Linking is used when constant number sequences are  
required, such as banking inquiries, answering machines, and  
voice mail.  
P a u s e D i a l i n g ( M e m o r y L i n k i n g )  
1. Enter the first group of numbers from the keypad or recall  
them from memory by pressing and the two-digit  
location number.  
2. Insert a pause by pressing Ï, Í. o will appear where the  
pause is inserted.  
3. Enter the next group of numbers, or recall them from memory  
by pressing Ï, and the two-digit location number.  
4. Repeat this sequence for as many groups as you wish up to a  
26  
MEMORY  
maximum of 24 digits. (Each pause occupies a digit.)  
However, in order to store this information to a memory loca-  
tion, each sequence can only contain 16 digits.  
5. To store a Linked Sequence, press Ø, then enter the two-  
digit location number where you wish to store the number.  
Two-Part Calling, as described on page 26, can be automated by a  
unique feature which permits the programming and memory stor-  
age of pauses between groups of numbers. When recalled or sent,  
the telephone stops transmitting at the pause and waits for your  
response (i.e., secondary dial tone).  
EXAMPLE: To construct a number sequence which you might use  
to inquire about your bank balance, follow this example.  
The bank’s telephone number is 123-4567. Your ID number is 888.  
Your account number is 22.  
NOTE: Pressing or £ may be required by the bank.  
Instruction and Key Sequence  
Display  
1. Enter the phone number of the bank—  
, ¤, , , , , ,  
or recall it from Memory Location 02—  
, , ¤.  
1234567  
2. Create a pause—  
Ï, Í.  
234567o  
67o888C  
3. Enter the ID number and a pound sign—  
°, °, °, £,  
or recall it from Memory Location 03—  
Ï, , , .  
4. Create another pause—  
Ï, Í.  
7o888Co  
88Co22C  
10  
5. Enter the account number and a pound  
sign— ¤, ¤, £.  
6. To store the number, press Ø and the  
two-digit location number. The memory  
location number will be displayed to  
confirm storage. Each memory location  
will only accept up to 16 digits.  
(Indicates the two -digit  
location number 10)  
27  
MEMORY  
IMPORTANT: Do not add PIN Code in Linked Sequence. Phone  
will automatically insert PIN Code when placing a Linked Call.  
Follow instructions on page 33.  
P l a c i n g  
a
L i n k e d C a l l  
Follow the procedure shown below to place a Linked Call from a  
sequence already stored to a memory location (see the example on  
the previous page to construct this sequence).  
1. Recall the Linked Sequence from its memory location by  
pressing , two-digit memory location.  
2. Wait for the system response, then press , Í to send the  
second group of numbers. Continue to press , Í at the  
time of system prompt until all digit groups are sent.  
IMPORTANT! To place a Linked Call with PIN Code, first follow  
the instructions on page 33. Your PIN Code will be automatically  
inserted in the Linked Sequence after the first pause by simply  
pressing , Í after you hear the system beeps.  
28  
FEATURES  
These features are designed to simplify operation or provide addi-  
tional convenience during special situations. The Feature Menu  
permits you to review, enable or disable most of your telephone’s  
features through the keypad and display.  
T o E n a b l e / D i s a b l e  
a
S p e c i f i c F e a t u r e  
1. Press Ï, .  
2. Scroll the menu by pressing or £ until the desired  
feature displays.  
3. Press Ç to change the status of the displayed feature  
between on and off.  
4. Press ´ to exit the Feature Menu.  
NOTE: ≤ or ≥ may also be used for scrolling to any feature in  
the Feature Menu.  
Feature Menu  
Feature  
Display  
One Minute Beep  
Individual Timer  
Distinctive Ringer  
Automatic Answer  
Multiple Key Answer  
Automatic Lock  
Emergency Dialing  
VOX  
ONE MiN TMR OFF  
iNDiV TMR OFF  
RiNGERSTYLE  
AUTO ANSR OFF  
MKEY ANSROFF  
AvTo LocK OFF  
EMRGCY CAII ON  
voX OFF  
Reminder Beeps  
PIN Code Activation  
REMiNDMSG ON  
PiN iNAcTivE  
29  
FEATURES  
D i s t i n c t i v e R i n g e r  
Your phone includes a new feature called Distinctive Ringer. This  
feature allows you to access one of nine different ringer styles.  
When this feature is selected, the phone will provide a brief sam-  
ple of that ringer style.  
1. Press Ï, .  
2. Scroll the menu by pressing or £ until the display  
shows:  
RiNGER  
STYLE  
3. Press Ç once to select this feature.  
The selected ringer will sound as an example of this ringer  
style. The ringer style will show:  
SELECT  
1-9  
4. Press - · to sample the different ringer styles.  
OR  
Press - £ to scroll through the ringer styles. The  
display will show the number of the selected ringer style.  
5. Press Ø to select the desired ringer style.  
The display will show:  
RiNGER  
XSET  
where the X is the number of the ringer style selected.  
6. Press ´ to exit the menu.  
A u t o m a t i c A n s w e r  
This feature permits you to answer calls without pressing Í. When  
your phone receives a call, it will ring twice and then the IU (In Use)  
indicator will illuminate and a tone will sound to let you know the call  
is live. Answer the call by lifting the phone to your ear.  
30  
FEATURES  
ANSR ON  
AvTo  
AvTo  
Feature enabled  
ANSR OFF  
Feature disabled  
To change this feature’s setting, enter the Feature Menu by follow-  
ing the instructions listed on page 29.  
M u l t i p l e K e y A n s w e r  
This allows the user to answer an incoming call by pressing Í,  
≤ or ≥ or any digit key, after the first ring has been completed.  
1. To activate this feature, enter the menu by pressing Ï, .  
2. Scroll with the and £ keys until you get to:  
MKEY  
ANSROFF  
3. Use Ç to turn feature on or off.  
A u t o m a t i c L o c k  
This feature automatically locks your phone each time it is turned off.  
AvTo  
AvTo  
LocK ON  
Feature enabled  
LocK OFF  
Feature disabled  
To change this feature’s setting, enter the Feature Menu by follow-  
ing the instructions listed on page 29.  
31  
FEATURES  
O n e - T o u c h E m e r g e n c y D i a l i n g  
Memory Location 01 may be used for an emergency number that  
you may wish to dial, even if your phone is locked.  
EMRGCY  
CAII ON  
Feature enabled  
EMRGCY CAII OFF  
Feature disabled  
To change this feature’s setting, enter the Feature Menu by follow-  
ing the instructions listed on page 29.  
When this feature is disabled, the number stored in Memory  
Location 01 will still be dialed if the phone is unlocked and if you  
press and hold , but EMRGCY will not appear in the display.  
NOTE: If Call Restriction Service Level 1 is enabled an emergency  
call will not be placed unless , , Í is used to override  
the restriction.  
NOTE: Automatic Redial does not work with Emergency Dialing  
when the phone is locked.  
V O X O p e r a t i o n  
Voice Operated Transmission (VOX) is a method of conserving bat-  
tery power by activating the unit’s transmitter only while talking. In  
this manner, your battery’s charge can be extended.  
Ask your Cellular System Provider if VOX Operation is supported  
in your area. If VOX is not supported in your system, VOX selec-  
tion will have no effect.  
voX  
Feature enabled  
ON  
voX  
Feature disabled  
OFF  
To change this feature’s setting, enter the Feature Menu by follow-  
ing the instructions listed on page 29.  
32  
FEATURES  
R e m i n d e r B e e p s (Available in some models only)  
Your Cellular Carrier may offer enhanced features such as Short  
Messaging. Ask your Cellular Service Provider if this is supported in  
your system. If Short Messaging is not supported in your system,  
Reminder Beep selection will have no effect.  
Reminder Beep is an audible notification to alert the user that they  
have received a message. It will beep every 2 minutes until the new  
messages have been read.  
1. Press Ï, .  
2. Scroll with the and £ keys until you get to:  
REMiND  
MSGON  
3. Use Ç to turn feature on or off.  
3. To exit Feature menu, press ´.  
To change this feature’s setting, enter the Feature Menu by follow-  
ing the instructions listed on page 29.  
P I N C o d e A c t i v a t i o n  
Your Cellular Carrier may require a Personal Identification Number  
(PIN) when placing outbound calls. This code assures the cellular  
system that the person placing the call is an authorized user. Ask  
your Cellular Service Provider if this is required in your system.  
Store you PIN Code in Memory Location 07 (Pfor PIN). A maxi-  
mum of 7 digits are allowed.  
PiN  
AcTivE  
Feature enabled  
PiN iNAcTivE  
Feature disabled  
To change this feature’s setting, enter the Feature Menu by follow-  
ing the instructions listed on page 29.  
33  
FEATURES  
1. Enter the number you wish to call.  
2. Press Í.  
3. Wait for double tone Beep Beep.  
4. Press Í.  
The phone will automatically send the PIN Code (stored in Memory  
Location 07).  
If you enter a service area which does not require a PIN Code, dis-  
able the feature in the Feature Menu.  
F e a t u r e S t a t u s R e v i e w  
To Review Status  
1. Press Ï, , ·, .  
2. Press or £ to scroll messages.  
To End Review  
1. Press ´.  
Status Review permits you to scroll through your operating settings  
for your reference.  
34  
TIMERS  
Call Timers provide a useful means of monitoring the air-time spent  
in conversation. Several of these operate in the background and  
can be displayed at any time.  
Each timer begins counting as a cellular channel is assigned, or  
when the phone rings to signal an incoming call. If an incoming  
call is not answered, the timers revert to their previous values.  
I n d i v i d u a l C a l l T i m e r  
To Display  
1. Press , £, £.  
This timer accumulates the air-time of  
and seconds.  
a
call in minutes  
It automatically resets before a new call is placed and when the  
phone is turned off.  
R e s e t t a b l e C a l l T i m e r  
To Display  
1. Press , £, £, £.  
To Reset  
1. Press Ï, , , Ç.  
This timer accumulates the air-time in minutes from the point at  
which it is reset.  
This Resettable Timer is generally utilized as a guide to track  
monthly air-time usage and is set in conjunction with the monthly  
billing cycle.  
C u m u l a t i v e C a l l T i m e r  
To Display  
1. Press , £, £, £, £.  
This non-resettable timer accumulates the phone’s total air-time in  
minutes, starting with the initial factory setting.  
35  
TIMERS  
O n e M i n u t e B e e p  
1. Press Ï, .  
2. Scroll the menu by pressing or £ until the display  
shows:  
ONEMiN TMRON  
Feature enabled  
ONEMiN TMROFF  
Feature disabled  
3. Press Ç once to turn this feature on or off.  
4. To exit the Feature Menu, press ´.  
Provides a tone ten seconds before the end of each minute  
during calls.  
36  
SECURITY FEATURES  
Your telephone offers several forms of security features against  
unauthorized use. Activating these features requires either your  
three-digit unlock code, or the six-digit security code. The factory  
programmed unlock code is 1, 2, 3 and the factory programmed  
security code is 000000.  
NOTE: It is common for the unlock code to be the last 3 digits of  
your phone number when it is programmed by your carrier.  
E l e c t r o n i c L o c k  
To Lock  
1. Press Ï, and hold .  
2. Phone will display Loc?.  
3. Press Ø to lock or press ´ to exit without locking  
the phone.  
4. Phone will display Loc/D.  
If a call is received during this period, the phone will ring and  
you must enter the unlock code before the call can be answered.  
To Unlock  
1. Enter your three-digit unlock code.  
NOTE: The factory preprogrammed unlock code is 1, 2, 3.  
The Electronic Lock prevents use of the telephone by disabling both  
incoming and outgoing calls. To help remember which key to use, note  
Lock appears on the key.  
If you make an error when entering your unlock code, press Ç  
and start again.  
D i s p l a y i n g U n l o c k C o d e  
1. Press Ï, .  
2. Enter your six-digit security code.  
3. Press . The unit will display Loc (and your three-digit  
unlock code).  
37  
SECURITY FEATURES  
C h a n g i n g U n l o c k C o d e  
1. Press Ï, .  
2. Enter your six-digit security code.  
3. Enter the new desired three-digit unlock code.  
4. Press Ø. The new unlock code will display to confirm storage.  
A u t o m a t i c L o c k  
This feature automatically locks your phone each time the unit is  
turned off.  
1. Press Ï, .  
2. Scroll the menu by pressing or £ until the desired  
feature displays.  
3. Press Ç once to change the status of the displayed feature  
between on and off.  
4. Press ´ to exit the Feature Menu.  
O u t g o i n g C a l l R e s t r i c t i o n s  
Your telephone can be set to restrict Call Placement (as when lend-  
ing the unit to another person). Using the six-digit security code,  
you may select one of the levels of restriction listed below.  
1. Press Ï, .  
2. Enter your six-digit security code.  
3. Enter the number of the Service Level (1 or 4) you wish  
to use.  
4. Press Ø. The unit will display LEVEL and the  
number selected.  
38  
SECURITY FEATURES  
Description  
Display  
No restrictions. (Standard setting)  
LEVEL 4  
LEVEL 1  
Phone will place calls only from memory  
locations 01-10. No keypad dialing. No memory  
storage. If locations 01-10 are cleared, no outgoing  
calls can be made.  
To change the unit to unrestricted operation, use the procedure  
above and enter service level 4.  
ACCESSORIES  
Motorola offers a variety of accessories for use with your cellular  
phone. The accessories packaged with your phone may vary.  
Accessories are available separately if they were not included with  
your phone. For optimum performance, we recommend you use  
Motorola approved batteries, chargers and other accessories with  
your phone. Be sure to use genuine Motorola batteries and acces-  
sories. Under its cellular telephone warranty, Motorola specifically  
disclaims any responsibility for damage caused by the use of  
portable cellular telephone accessories not manufactured or sup-  
plied by Motorola.  
B a t t e r i e s  
The Motorola batteries packaged with your phone are discharged  
and must be fully charged before use. Prior to initial use, it is rec-  
ommended that new batteries be charged overnight. Performance  
may be affected if batteries are not charged in an approved  
Motorola charger.  
Your battery needs no maintenance other than routine charging.  
The battery should be at or near room temperature when charging.  
WARNING: Battery may explode if disposed of in fire.  
CAUTION: To prevent injuries or burns, do not allow metal objects  
to contact or short circuit the battery terminals.  
Motorola offers a wide selection of batteries to meet your changing  
needs.  
Nickel Metal Hydride Batteries  
Your phone package may have included a nickel metal hydride  
39  
ACCESSORIES  
battery. Nickel metal hydride batteries are high capacity batteries  
which offer up to 30% more talk time than comparable nickel cad-  
mium batteries. Several sizes and capacities are available. To help  
achieve maximum life and capacity of your new nickel metal  
hydride battery, it is suggested that you charge with Motorola  
approved chargers, and do not leave the battery in the charger for  
more than 24 hours.  
Nickel Cadmium Batteries  
Motorola offers many sizes and capacities of rechargeable nickel  
cadmium batteries for your phone. Nickel cadmium batteries can be  
optimally charged with any approved Motorola charger. To insure  
maximum life and capacity of your new nickel cadmium battery, do  
not leave the battery in the charger for more than 24 hours.  
Alkaline Batteries  
A NON-rechargeable battery housing that holds alkaline batteries  
is available as an option. The Alkaline Talk PAK is ideal as a spare  
battery or emergency back-up. Six standard AA alkaline batteries  
can be used, and provide up to three and a half hours of continu-  
ous talk time for your phone.  
C h a r g e r s  
AC Charger/Transformer  
The AC Charger/Transformer allows you to plug your phone  
directly into a power supply and charge attached batteries. This AC  
Charger/Transformer is very compact, making it ideal for home or  
travel.  
To attach the AC Charger/Transformer to your phone, locate the metal  
contacts on one side of the AC Charger/Transformer, as well as those  
on the bottom-rear of the phone. Match the metal contacts together,  
making sure that the white dot on the AC Charger/Transformer faces  
40  
ACCESSORIES  
the same direction as the front of the telephone. You will hear a  
click to indicate that the connection has been properly made. Plug  
the AC Charger/Transformer in an AC wall outlet.  
In order to optimize battery charge time, plugging in the AC  
Charger/Transformer will power your phone off. The phone cannot  
be powered on while the AC Charger/Transformer remains plugged  
in. If you need to make or receive a call, you will need to unplug  
the AC Charger/Transformer from the phone.  
AC Charger Rates  
Battery Type  
Hours (to 90% Capacity)  
Standard Slim NiMH  
Standard NiCd  
6.5  
8
Extra Capacity NiMH  
Extra Capacity NiCd  
13  
13  
Overnight Dual Charger  
The Overnight Dual Charger accommodates any two batteries. The  
front pocket can recharge a battery with the phone attached. The  
yellow lamps indicate that the unit or batteries are properly inserted  
and charging. The lamp on the charger will not change color or  
extinguish when charging is complete.  
Overnight Dual Charger Rates  
Battery Type  
Hours (to 90% Capacity)  
Standard Slim NiMH  
Standard NiCd  
9
7.5  
12  
Extra Capacity NiMH  
Extra Capacity NiCd  
12  
IntelliCharge™ XT Rapid Charger  
The optional IntelliCharge™ XT Rapid Charger accommodates any  
two batteries. The front pocket can recharge a battery with the tele-  
phone attached.  
41  
ACCESSORIES  
NOTE: It is recommended that  
Talk Pak batteries be charged in  
the front pocket.  
The battery in the front pocket has  
priority and if it is in range, is rapid  
charged first. Once the rapid charge  
of the front pocket battery is complete, the charger switches to rapid  
charge of the second battery.  
Each pocket of the IntelliCharge™ XT Rapid Charger has its own  
multi-color lamp to indicate that the battery and/or telephone have  
been properly placed in the charger pocket and that the battery is  
either rapid charging (red) or trickle charging (green). A flashing yel-  
low lamp indicates that the battery is out of range for a rapid charge,  
or waiting for the battery in the priority pocket to be charged first.  
To protect the battery, rapid charging halts prior to reaching full  
charge and trickle charging begins. Leave the slim and standard  
batteries in the IntelliCharge™ XT Rapid Charge for two additional  
hours to reach full capacity, three additional hours for an Extra  
Capacity battery.  
Batteries will not rapid charge when they are below 50°F (10°C) or  
above 113°F (45°C). In addition, new batteries (or batteries which  
have been stored without use) may not rapid charge. In these  
instances, the charger light will turn green within one minute, indi-  
cating the need for overnight charging. Leave the slim and standard  
batteries in for 10 hours to reach full capacity. New batteries may  
take up to five discharge/overnight recharge cycles before reaching  
maximum capacity.  
NOTE: If you have an IntelliCharge™ Rapid Charger and an  
Overnight Dual Charger, be certain to plug each charger’s trans-  
former into the proper base. They are not interchangeable.  
IntelliCharge™ XT Charger Rates  
Battery Type  
Minutes (to 90% Capacity)  
Standard Slim NiMH  
Standard NiCd  
65 Min.  
55 Min.  
90 Min.  
85 Min.  
Extra Capacity NiMH  
Extra Capacity NiCd  
42  
ACCESSORIES  
U l t r a S a v e r  
The optional Ultra Saver requires no installation and allows you to  
power your telephone from a vehicle’s battery via the cigarette  
lighter. This is particularly valuable when driving rental cars. While  
using the Ultra Saver, you conserve your phone’s battery, and also  
provide a slow charge to the battery. To attach the Ultra Saver to  
your phone, locate the metal contacts on the flat side of the Ultra  
Saver connector, as well as those on the bottom-rear of the phone.  
Match the metal contacts together, making sure that the white dot  
on the Ultra Saver connector faces the same direction as the front  
of the telephone. You will hear a click to indicate that the connec-  
tion has been properly made. Plug the Ultra Saver into the vehicle’s  
cigarette lighter socket.  
Your telephone will now be powered by the vehicle’s battery rather  
than the telephone’s battery. The keypad backlighting and display  
will remain on as long as the Ultra Saver is attached to the unit and  
plugged into the vehicle.  
NOTE: The Ultra Saver has a three-amp fuse, which you may  
replace yourself if necessary.  
To remove the Ultra Saver from the phone, use one of the two fol-  
lowing methods.  
Standard Method  
Turn off your telephone, then squeeze both sides of the Ultra Saver  
connector until the tabs release. Then remove the connector from  
the rear of the phone.  
Quick Change Method  
This method allows you to unplug your telephone from the Ultra  
Saver during a telephone call without losing the call. Unplug the  
43  
ACCESSORIES  
coil cord from the telephone by squeezing both sides of the Ultra  
Saver connector until the tabs release, then press .  
This will return you to your telephone call. The phone will not go  
through the normal power-up cycle described on page 15. You will  
only have five seconds to complete this action before your tele-  
phone call is terminated. Advise the party on the other end of the  
call before beginning this procedure.  
T r a v e l C h a r g e r  
The optional small, compact and lightweight DPC Travel Charger  
can charge any size battery. For nickel cadmium or nickel metal  
hydride, the standard batteries will recharge in approximately 5  
hours or less, the larger extra capacity batteries in approximately 10  
to 15 hours. Simply attach your battery to the charger in the same  
manner as your phone. A yellow light indicates that the battery is  
properly inserted and charging.  
M i s c e l l a n e o u s A c c e s s o r i e s  
Carry Case  
Durable leather or vinyl carry cases to protect your phone with any  
size battery attached are available.  
Headset  
An earphone and microphone in one small piece that connects  
directly into the optional headset jack on the side of your phone is  
available for simple hands-free and private telephone conversations.  
To use the headset, simply plug in the headset. Your phone will  
operate normally, except for a few features that occur only when  
the headset is plugged in. Remember to press ´ to end your call  
when the headset is connected.  
To easily answer a call when using the headset, the Multiple Key  
Answer always turns on whenever the headset is plugged in. This  
will allow you to answer a call simply by pressing the volume keys.  
To adjust the volume of the earpiece, press the desired volume key  
with the headset attached. The headset can be connected or dis-  
connected at any time without affecting a call in process. To termi-  
nate the call, press ´.  
NOTE: Some jurisdictions prohibit or regulate your use of a head  
44  
ACCESSORIES  
set while driving a vehicle. Please check the laws of your jurisdic-  
tion before purchasing or using a headset.  
THE Portable Cellular Connection™ Interface  
Your phone is data compatible and may be used in conjunction  
with THE Portable Cellular Connection Interface to connect to  
peripheral devices that are compliant with telephone industry RJ-11  
specifications.  
THE Portable Cellular Connection kit for your phone series consists of  
the Portable Cellular Connection Interface box and a cable that con-  
nects the interface box to the accessory connector on the bottom of  
the phone. The interface box includes mounting clip, rechargeable  
nickel cadmium battery and an outlet for charging. The diagram  
below shows typical connections for this type of interface.  
RJ 11  
Device  
888  
8888888  
Modular  
Connector  
Cellular  
RJ 11  
Connection  
Connector  
Wall Transformer  
or Car Adapter  
Examples of such peripheral devices:  
• FAX (facsimile machine)  
• Personal Computer  
CELLect™ PCMCIA or POCKET Modems  
Send and receive FAXes, E-mail and data (from data peripherals)  
with your cellular phone. Simply connect the appropriate data  
cable to the accessory connector on the bottom of the phone and  
to the CELLect modem on the other end. The PCMCIA modem  
works with data devices using a standard PCMCIA Type II slot, and  
the Pocket modem connects to a data device through a standard  
serial communications connector.  
45  
ACCESSORIES  
Compaq Direct Connect  
The direct connection cable allows Compaq computers using  
Compaq’s SpeedPAQ™ 144 internal modem to transmit data or  
FAXes over the cellular system. Simply connect one end of the  
cable to your phone and the other end to the cellular connector on  
the modem.  
SpeedPAQ is a trademark of Compaq Computer Corporation.  
46  
ROAMING AND SYSTEM OPERATION  
There are generally two types of cellular systems serving any met-  
ropolitan area. One of these will most likely be operated by the  
telephone company that provides telephone service to your com-  
munity, generally referred to as a wireline carrier. The other  
Cellular Service Provider is a radio common carrier, referred to as  
a non-wireline carrier.  
Your Cellular Service Operator will provide information concern-  
ing specific features, procedures, and coverage in your  
particular area.  
S e r v i c e A r e a  
The area within which the telephone operates is defined by your Cellular  
Service Provider. Since this is a radio system, no exact boundaries (as on  
a map) can be drawn. The red NS (No Service) lights if you are beyond  
range of a service area. There may be locations within your area, such  
as tunnels and underground parking facilities where the unit may act as  
if it were beyond range.  
W e a k S i g n a l A l e r t  
If you are called while in a location the system determines is inadequate  
for high quality service, you may hear a series of beeps to inform you of  
the call attempt. The caller will receive the recorded Not in Service”  
message, CALL appears in the display, and the green on indicator flashes  
quickly. If this occurs, you must press Ç before the unit will operate.  
Most systems do not impose air-time charges for such call attempts. This  
feature is usually turned off.  
NOTE: This indicator is controlled through the initial programming of  
your phone. Refer to the Programming Guide for more details.  
R o a m i n g  
The term Roamingapplies to the use of cellular telephones within sys-  
tems other than those designated as their Homesystem. RM (Roam)  
lights whenever the unit comes within range of a visited system. As your  
phone begins to roam, it seeks service according to the conditions you  
have selected.  
Slow flashing of RM (Roam) signals that your phone unit is accessing a  
home type system, while rapid flashing indicated the unit is attempting  
connection through a non-home type system.  
47  
ROAMING AND SYSTEM OPERATION  
Contact your system operator, or that of the visited system, for informa-  
tion on dialing and billing procedures.  
To use alternate long distance services when roaming, be certain to dial  
the appropriate area code and local number to access the alternate car-  
rier in the visited area. Then use the Tone Dialing sequence described on  
page 26. If you selected Two-System Operation (see page 21) enter ,  
£ to verify the currently active number. This is especially important if  
your two home systems have different area codes, or if RM (Roam) is  
flashing within home service area.  
S e l e c t a b l e S y s t e m R e g i s t r a t i o n  
To Review Current Setting:  
1. Press , .  
The display will show the current active system choice.  
2. Repeatedly press to review the System Type modes.  
(Press ´ to exit without changing selections.)  
3. Press Ø to activate the displayed selection.  
System Type Selection  
C Scan  
Display  
CSCAN  
When programmed, this is the default setting.  
Standard Mode  
Your phone first seeks a home type system, then  
a non-home type.  
If home system is non-wireline (type A)  
If home system is wireline (type B)  
Invert Preference Mode  
STD AB  
STD BA  
Your phone first seeks a non-home type system,  
then home type. (Select this mode if in a fringe  
area of your home system or in certain  
roaming situations.)  
If home system is non-wireline (type A)  
SCAN BA  
Fast flashing RM (Roam) indicator = call on B system  
Slow flashing RM (Roam) indicator = call on home  
type system  
Slow flashing IU (In Use) indicator = call on  
home system  
48  
ROAMING AND SYSTEM OPERATION  
System Type Selection  
Display  
If home system is wireline (type B)  
Flashing RM (Roam) indicator = call on A system  
SCAN AB  
Slow flashing RM (Roam) indicator = call on home  
type system  
Slow flashing IU (In Use) indicator = call on  
home system  
Home Only Mode  
XOME  
Phone will not operate outside its home system.  
Scan A Mode  
SCAN A  
Phone will operate only within non-wireline  
(A) systems.  
Scan B Mode  
SCAN B  
Phone will operate only within wireline  
(B) systems.  
Enter SID Mode (Available in some models only) PREF /D SiDS  
Unit will operate only within specifically  
identified systems. This choice requires entry of  
up to 15 System ID numbers for those systems  
over which you wish to operate. The SID digits  
are entered as obtained from your Cellular  
Service Operator. When Preferred SIDS is  
enabled, C Scan Mode is disabled. See page 50.  
C h a n g i n g S y s t e m T y p e  
The choice of System Type, as described on page 48, may be  
selected or canceled as follows:  
1. Press , . The display shows the current active choice.  
Repeatedly press until the desired System Type appears  
in the display.  
2. If you chose Preferred SIDS, press Ø and then enter the  
five-digit number at this time. Use and £ to move to  
the next SID location.  
3. To activate the selection, press Ø.  
4. To return to normal operation, press ´.  
49  
ROAMING AND SYSTEM OPERATION  
NOTE: Constant flashing of the RM (Roam) indicator, or a steadily  
lit NS (No Service) indicator while within your home service area  
may indicate an unintentional choice has been made. If this occurs,  
re-enter System Type Selection to see if the unit is operating in  
Standard Mode, or if an alternate selection has been made.  
C
S c a n  
Your Motorola cellular telephone may be equipped with a special  
level of A/B System Selection called C Scan. Check with your service  
shop. This feature will limit the systems on which you can inadver-  
tently operate and thus minimize billing problems. C Scan is a fea-  
ture that must be activated or deactivated by a Motorola Authorized  
Service Center or dealer.  
When C Scan is activated Preferred SIDS will be deactivated. See  
page 49.  
If you review the Roam characteristics of your phone with the ,  
sequence, C Scan will be the first choice that appears in the dis-  
play if you have at least one negative system ID entered. Repeatedly  
pressing £ or will scroll through the other five system selec-  
tion choices as shown on page 48. You may press Ø to select an  
alternate choice when it appears in the display. Your choice will  
remain in effect until you turn off your telephone. On every power-  
up cycle, the telephone will automatically revert back to the C Scan  
mode of operation.  
When the NS (No Service) indicator blinks, you are either in an area  
that cannot give you service due to the C Scan mode, or when no  
cellular service is available. In either case, you may select another  
level of A/B system selection as described previously. If you have  
selected standard preference or invert preference and the NS (No  
Service) indicator is on, you are in a true no service areawhere  
cellular service is not available.  
50  
BEFORE CALLING FOR SERVICE  
Is the unit locked?  
See Electronic Lock, page 37.  
Is the NS (No Service) indicator lit?  
See page 16.  
Is a unique operating mode programmed?  
Constant flashing of RM (Roam) while in your home service area  
may indicate that an incompatible System Type has been selected.  
See System Type Selection, page 48.  
Is the unit operating with non-standard settings?  
If when you first turn the unit on, o is displayed, you may have  
inadvertently selected improper operating characteristics. See  
Feature Status Review, page 34.  
Have you selected the wrong home system?  
If your unit is programmed for Two-System Operation, press ,  
£ to display the active telephone number. See Two-System  
Operation, page 21.  
Have you charged the battery?  
Place the unit in the charger and verify that the charger indicator  
lamp is lit. If it does not light, check all wire connections and  
remove and reseat the battery. See Preparing Battery for Initial Use,  
page 12.  
51  
MESSAGE GLOSSARY  
A
key displayed as A”  
System Aphone number 1  
System Aphone number 2  
A1  
A2  
AUTO ANSROFF Automatic Answer feature  
MKEY ANSROFF Multiple Key Answer Feature  
B1  
B2  
System Bphone number 1  
System Bphone number 2  
Battery Meter  
C
Precedes Cumulative Timer display (also used  
to display £ key)  
CALL  
Shows incoming call, Call in Absence, or  
Weak Signal Alert  
CHANGE?  
C SCAN  
Overwrite number in Selected Memory Location  
System Type Selection (default setting)  
Emergency Dialing in progress  
EMRGCY  
52  
MESSAGE GLOSSARY  
EMRCY OFF  
FULL  
Emergency Dialing feature  
Selected Memory Location is full  
System Type Selection — Home Mode  
Call Restriction selected  
XOME  
LEVEL 1  
LEVEL 4  
No Restrictions (standard setting)  
AUTOLOCKOFF Automatic Lock feature  
LO BAT  
Low Battery  
Loc/D  
MUTE  
Unit is locked  
Microphone muted  
No SERvicE No Service  
oN  
Telephone is on  
PiN AcTivE PIN Code Activation  
PREF /D SiDS System Type Selection (SID mode)  
R
Precedes Resettable Call Timer Display  
REDIAL  
Automatic Redial  
53  
MESSAGE GLOSSARY  
REMiND MSGON  
Reminder Beeps  
Signal Strength Meter  
SCAN A  
SCAN AB  
SCAN B  
SCAN BA  
STD  
System Type Selection (scan non-wireline Aonly)  
System Type Selection (scan Atype first, then B)  
System Type Selection (scan wireline Bonly)  
System Type Selection (scan Btype first, then A)  
All user features set to standard  
STD AB  
STD BA  
System Type Selection (non-wireline standard mode)  
System Type Selection (wireline standard mode)  
SYSTEM BvSY System Busy  
v=  
vOX  
Volume Meter  
Voice-Operated Transmission (VOX) selected  
VOX Mode feature  
vOX MODE  
54  
INDEX  
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Adjusting Earpiece Volume . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Adjusting Ringer Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Antenna System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Automatic Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Automatic Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31, 38  
Automatic Redialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
BEFORE CALLING FOR SERVICE. . . . . . . . . . . . . . . . . . . . . . 51  
C Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
Call in Absence Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Changing Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Changing System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Changing Unlock Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Charger Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-42  
Chargers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Clearing Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Cumulative Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
55  
INDEX  
Displaying Battery Voltage Meter. . . . . . . . . . . . . . . . . . . . . . 19  
Displaying Own Phone Number . . . . . . . . . . . . . . . . . . . . . . 20  
Displaying Unlock Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Distinctive Ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Earpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Electronic Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Enable/Disable a Specific Feature . . . . . . . . . . . . . . . . . . . . . 29  
Feature Status Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
GENERAL SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . 6  
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Illuminated Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Individual Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
TM  
IntelliCharge XT Rapid Charger . . . . . . . . . . . . . . . . . . . . . . 41  
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Low Battery Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Memory Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Memory Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
MESSAGE GLOSSARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
56  
INDEX  
Mouthpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Multiple Key Answer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Muting Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Nickel Metal Hydride Batteries . . . . . . . . . . . . . . . . . . . . . . . 39  
Number Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
One-Touch Emergency Dialing . . . . . . . . . . . . . . . . . . . . 25, 32  
Outgoing Call Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Overnight Dual Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Patent Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
Pause Dialing (Memory Linking) . . . . . . . . . . . . . . . . . . . . . . 26  
PHONE OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
PIN Code Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Placing a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Placing a Linked Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Preparing Battery for Initial Use. . . . . . . . . . . . . . . . . . . . . . . 12  
Quick Change Method (Battery). . . . . . . . . . . . . . . . . . . . . . . 14  
Quick Change Method (Ultra Saver) . . . . . . . . . . . . . . . . . . . 43  
QUICK REFERENCE SECTION. . . . . . . . . . . . . . . . . . . . . . . . 61  
Recalling Area Code/Prefix (Postscripting) . . . . . . . . . . . . . . . 24  
Recalling From Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
57  
INDEX  
Recalling Last Number Called . . . . . . . . . . . . . . . . . . . . . . . . 24  
Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Reminder Beeps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Resettable Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Roaming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
ROAMING AND SYSTEM OPERATION . . . . . . . . . . . . . . . . . 47  
Scratch Pad Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
SECURITY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Selectable System Registration. . . . . . . . . . . . . . . . . . . . . . . . 48  
Service Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Signal Strength Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Standard Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Storing Numbers to a Memory Location. . . . . . . . . . . . . . . . . 22  
Super Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Switching to a Second Phone Number. . . . . . . . . . . . . . . . . . 21  
System Type Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-49  
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
TM  
THE Portable Cellular Connection . . . . . . . . . . . . . . . . . . . . 45  
58  
INDEX  
TIMERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Tone Dialing (Two-Part Calling) . . . . . . . . . . . . . . . . . . . . . . . 26  
Turbo Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Turn Phone On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Two-System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Ultra Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Unlocking Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Volume Meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
VOX Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Weak Signal Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
WELCOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
59  
PATENT INFORMATION  
Manufactured under one or more of the following U.S. patents:  
4121218 4648125  
4124879 4649543  
4127824 D288683  
4138681 4654655  
4193036 D289156  
4254382 4662691  
4302845 4667333  
4312074 4668917  
4327319 4670747  
4329666 4672502  
4369516 4680787  
4369522 4681476  
4378603 4683585  
4390963 4692726  
D269873 4704588  
4398265 D292578  
4400584 4706036  
4400585 D292920  
D270835 4710724  
D271491 4711361  
Re.31470 4715063  
4431977 4716319  
4434461 4716391  
4455534 4723305  
4462098 D294257  
D275951 4727306  
4484153 4727583  
4485486 4730195  
4486624 4734635  
D276809 4736277  
4491972 4737976  
D277667 4740794  
4504834 4741018  
D278708 4741034  
4523155 4742562  
4546329 D295627  
4550426 4746242  
4551696 D295973  
4564821 D295975  
D282169 4751737  
4571595 D296187  
4573017 4761621  
4574243 4764737  
4585957 D297734  
4602218 D297735  
D284759 4777564  
D285439 Re.32768  
4616314 D299136  
4617520 4797929  
D286778 4798975  
4626309 4800348  
4628529 4802236  
4629829 4809356  
4630304 4811377  
4630305 4811404  
4633141 4827226  
4636593 4827507  
4636741 4829274  
D288432 4837534  
D301476 5059885  
4843621 5060294  
4845772 D322783  
D302015 D322955  
4851966 5081674  
4868576 5083304  
4870686 D324024  
D303656 D324388  
4876552 5095503  
4879533 D325028  
D305427 D325583  
4896124 5109536  
4897873 D325915  
D305717 5113436  
4904549 5117450  
4905288 5121047  
4905301 5122480  
D306293 5122722  
D306441 D327061  
D306594 5128834  
4912602 D328302  
4918732 5142551  
4922178 5142696  
4945570 5146620  
4954796 5148471  
4959851 5148473  
4963812 5148961  
4963843 5150359  
4965537 5150384  
4972355 5152006  
4972432 5157693  
4972455 5163159  
4975808 5164652  
4984290 5166596  
D314173 5175759  
D315330 5175874  
D315346 D332261  
D315543 5182749  
D315559 D332785  
D315565 5185566  
5004992 5187809  
D315907 5193223  
5008925 5195106  
D316417 5195108  
D316859 5201069  
5017856 5204977  
5018188 5210793  
5020091 5214675  
5020092 5222104  
5020093 5222251  
5028083 D337332  
5028859 5230007  
5029044 5230093  
5029233 5233633  
5031028 5235492  
5036532 5237257  
5053924 5239127  
5057762 5241545  
D320780 5241548  
5241650 5453997  
5241693 D362840  
5242767 5457744  
D339582 5459640  
5249302 5463646  
5251331 5465412  
D340710 5469177  
5260988 5475752  
5261119  
D365094  
5262710 D365817  
5263052 5486843  
5276707 5487184  
5278994 5488335  
D343173 5488649  
5280637 D366872  
D344087 5493198  
5287553 5493714  
5287555 5497126  
5287556 5497382  
D344511 D367640  
5301365 5499394  
5321847 5506490  
D348880 D368696  
5349588 5510693  
5359696 5511235  
5361400 D369162  
5363071 5513078  
5365549 D369359  
D352497 5519303  
5366826 5519346  
D353131 5524276  
D353361 5524278  
5375143 D370463  
5375258 5530922  
5379324 5542116  
D354055 5544250  
D354062 D372481  
5384825 5546275  
D356084 5546380  
5402447 D372896  
5406146 5551078  
5406562 5559471  
D357224 D374424  
D357457 D374872  
5410741 5572193  
D357680 5574976  
D357681 5577268  
5428836 D375732  
D359734 D375733  
D359735 D375734  
D359959 D375932  
5432017 D376127  
D360632 5588041  
5438684 5589796  
D361070 5590177  
5442680  
5446763  
5448763  
5448771  
Other patents pending.  
60  
QUICK REFERENCE SECTION  
Turn On  
Unlock  
Press .  
Enter the three-digit unlock code. If you make  
an error, press Ç and enter again.  
Place Call  
Turbo Dial  
Enter number, press Í.  
Press and hold any digit key ¤ - ·. Dials  
number stored in that memory location.  
Receive Call  
End Call  
Press Í.  
Press ´.  
Store Number  
Enter number, press Ø, then the two-digit  
Directory Location Number.  
Recall Number  
Press , then the two-digit Directory  
Location Number.  
Call Number Displayed  
Lock Unit  
Press Í.  
Press Ï, , Ø.  
Press Ï, .  
Review Battery Meter  
Adjust Volume  
Earpiece— Press and hold to increase.  
Release, press again to decrease.  
Ringer— Press Ï, then ≤ or ≥ as above.  
Recall Last Number Used Press , .  
Recall Own  
Press , £.  
Phone Number  
Individual Call Timer  
Resettable Call Timer  
Cumulative Call Timer  
Access Features Menu  
Press , £, £.  
Press , £, £, £.  
Press , £, £, £, £.  
Press Ï, .  
Review/Scroll  
Menu Features  
Press to scroll forward, £ to  
scroll back.  
Status Review  
Press Ï, , ·, . Press or  
£ to scroll through messages.  
61  
THIS PRODUCT MAY BE POWERED BY A  
RECHARGEABLE BATTERY WHICH MUST BE  
RECYCLED OR DISPOSED OF PROPERLY.  
• Refer to the battery label for battery type.  
• Recycling facilities may not be available in all areas.  
• For additional information regarding disposal or recycling call  
1-800-331-6456.  
For information about your product, or  
accessories for your product,  
please call Motorola’s Cellular Customer  
Response Center;  
in U.S.,1-800-331-6456;  
in Canada, 1-800-461-4575.  
For information about your cellular service,  
please call your service provider (Carrier).  
Please visit us at:  
and Motorola are trademarks of Motorola, Inc.  
Printed in U.S.A.  
© 1995 Motorola, Inc.  
68P09396A92-A  
1/29/97-RGC  

Nokia 103 User Manual
Motorola MOTORAZR V3t User Manual
Motorola i455 User Manual
Kyocera Cell Phone 3035 User Manual
Kenwood CD Player KDC MP3046 User Manual
JVC KD S723R User Manual
Hitachi CP L540E User Manual
Fujitsu MPB3043AT User Manual
Fujitsu Computer Drive MAP3367NP User Manual
American Audio CDI 300 User Manual