CD-RECEIVER
KDC-X917
KDC-X817
KDC-9017
KDC-X717
INSTRUCTION MANUAL
COMPACT
DIGITAL AUDIO
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the
best performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on
the warranty card, and in the space provided below. Refer to the model and serial
numbers whenever you call upon your KENWOOD dealer for information or service on
the product.
Model KDC-X917, KDC-X817, KDC-9017, KDC-X717 Serial number
© B64-1891-00 (KW)
Contents
Safety precautions ...................4
Handling Compact discs...........6
Tuner features
Menu settings
Tuning...................................................20
Station Preset Memory ........................20
Auto Memory Entry..............................20
Direct Access Tuning ...........................21
Station Name Preset (SNPS) ................22
Station Name Preset Play (SNPP) .......23
Menu System .......................................33
Security Code .......................................34
Touch Sensor Tone...............................35
Manual Time Adjustment .....................35
Calendar Adjustment ............................35
Calendar Mode .....................................35
Memo Mode.........................................36
Automatic Time Adjustment.................36
Selectable Illumination..........................37
Switching Display Mode.......................37
Icon/Spectrum analyzer Select .............37
Font Select............................................37
Brightness level adjustment.................37
Dimmer.................................................38
Time setting for removing
General features
Power .....................................................8
Volume....................................................9
Attenuator...............................................9
Switching Modes....................................9
Loudness ..............................................10
System Q..............................................10
Speaker & Woofer setting....................10
Faceplate Angle Adjustment ................11
Switching Full-Screen Display ..............11
Switching the Upper Part Display.........12
Switching the Lower Part Display ........12
Forced Closing......................................14
Removing the Faceplate.......................14
Non-Fading Output ...............................15
RDS features
RDS (Radio Data System).....................24
Alarm ....................................................24
Radio Text Scroll...................................24
Program Type (PTY) Function...............24
Registration of a station as a PTY ........25
CD/External disc control features
Playing CDs...........................................26
Playing Other Disc mode......................27
Fast Forwarding and Reversing Disc Play
..............................................................27
Track Search .........................................27
Disc Search...........................................28
Track / Disc Repeat...............................28
Track Scan ............................................28
Random Play.........................................28
Text Scroll.............................................29
Presetting Disc Names (DNPS) ............30
Magazine Random Play ........................31
Direct Track Search ..............................31
Direct Disc Search................................32
Disc Name Preset Play (DNPP) ...........32
the faceplate.........................................38
System Q..............................................38
Built-in Amp Mute Control....................38
Dual Zone System ................................38
External Amp Control ...........................39
Traffic Information Function .................39
Clean Reception System Circuit
Audio control features
Audio Control Setting ...........................16
Bass Center Frequency ........................16
Bass Level ............................................16
Bass Quality Factor...............................16
Bass Extend..........................................16
Middle Center Frequency.....................17
Middle Level .........................................17
Middle Quality Factor ...........................17
Treble Center Frequency......................17
Treble Level ..........................................17
Balance Level........................................17
Fader Level ...........................................17
Non-Fading Level..................................17
High-pass Filter Frequency
(CRSC) .................................................39
Text Scroll.............................................39
Basic Operations of remote....40
Installation
Accessories ..........................................43
Installation Procedure ...........................43
Connecting Wires to Terminals ............44
Installation (non-Japanese cars)............45
Locking the faceplate to the unit..........45
Removing the Unit................................46
Installation (Japanese-cars)...................47
for Front Output....................................18
High-pass Filter Frequency
for Rear Output.....................................18
Low-pass Filter Frequency
Troubleshooting Guide...........48
Specifications.........................52
for Non-Fading Output..........................18
Phase for Non-Fading Output...............18
Volume Offset ......................................18
— 2 —
2Warning
NOTE
2CAUTION
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous
radiation exposure.
In compliance with Federal Regulations,
following are reproductions of labels on, or
inside the product relating to laser product
safety.
reasonable protection against harmful
interference in a residential installation. This
equipment may cause harmful interference
to radio communications, if it is not installed
and used in accordance with the instructions.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
Location : Bottom Panel
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications
to this equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction manual.
The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
NOTE
This Class B digital apparatus complies with
Canadian ICES-003.
— 3 —
Safety precautions
IMPORTANT INFORMATION
About the disc changer to be
2WARNING
2CAUTION
To prevent injury or fire, take the
To prevent damage to the machine,
take the following precautions:
• Make sure to ground the unit to a negative
12V DC power supply.
• Do not open the top or bottom covers of
the unit.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or
humidity. Also avoid places with too much
dust or the possibility of water splashing.
• Do not subject the faceplate to excessive
shock, as it is a piece of precision
equipment.
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse
with the wrong rating may cause your unit
to malfunction.
• To prevent a short circuit when replacing a
fuse, first disconnect the wiring harness.
• Do not place any object between the
faceplate and the unit.
• Do not use your own screws. Use only the
screws provided. If you use the wrong
screws, you could damage the unit.
• Do not apply excessive force to the moving
faceplate. Doing so will cause damage or
malfunction.
• Do not apply excessive force to the open
faceplate or place objects on it. Doing so
will cause damage or breakdown.
connected:
To connect a disc changer having the "O-N"
switch to this unit, set the "O-N" switch to
"N".
following precautions:
• Insert the unit all the way in until it is fully
locked in place. Otherwise it may fall out of
place when jolted.
When you connect a model with no "O-N"
switch, the converter cord CA-DS100
available as an option may be required. For
details, consult your Kenwood dealer.
If a model with no "O-N" switch is
connected, some unavailable functions and
information that cannot be displayed are
generated, such as the DNPS, DNPP,
Magazine random play, and CD Text display.
Note that none of the KDC-C100, KDC-C302,
C205, C705, and non-Kenwood CD changers
can be connected.
• When extending the ignition, battery, or
ground wires, make sure to use
automotive-grade wires or other wires with
2
a 0.75mm (AWG18) or more to prevent
wire deterioration and damage to the wire
coating.
• To prevent a short circuit, never put or
leave any metallic objects (such as coins or
metal tools) inside the unit.
• If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
• Make sure not to get your fingers caught
between the faceplate and the unit.
• Be careful not to drop the unit or subject it
to strong shock.
The unit may break or crack because it
contains glass parts.
2CAUTION
You can damage both your unit and
the CD changer if you connect them
incorrectly.
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter
into the unit, the adapter might separate
from the CD and damage the unit.
— 4 —
• The illustrations of the display and the
panel appearing in this manual are
examples used to explain more clearly how
the controls are used. Therefore, what
appears on the display in the illustrations
may differ from what appears on the
display on the actual equipment, and some
of the illustrations on the display may
represent something impossible in actual
operation.
• The functions that can be used and the
information that can be displayed will differ
depending on the external disc players
being connected.
Cleaning the CD Slot
NOTE
As dust tends to accumulate in the CD slot,
clean it every once in a while. Your CDs can
get scratched if you put them in a dusty CD
slot.
• If you experience problems during
installation, consult your Kenwood dealer.
• If the unit fails to operate properly, press
the RESET button. The unit returns to
factory settings when the RESET button is
pressed. If the unit still fails to operate
properly after the RESET button has been
pressed, contact your local KENWOOD
dealer for assistance.
• Press the reset button if the disc auto
changer is first controlled and operates
incorrectly. The original operating condition
will return.
DAB
OFF
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
Lens Fogging
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the CD player of the unit. Called
lens fogging, CDs may be impossible to play.
In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit
still does not operate normally after a while,
consult your Kenwood dealer.
AUTO
AME
AUD
NF
Cleaning the Unit
If the faceplate of this unit is stained, wipe it
with a dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the
stain off with a cloth moistened with neutral
cleaner, then wipe neutral detergent off.
Reset button
• We recommend the use of the Security
Code function (see p. 34) to prevent theft.
2CAUTION
Applying spray cleaner directly to the unit
may affect its mechanical parts. Wiping the
faceplate with a hard cloth or using a volatile
liquid such as thinner or alcohol may scratch
the surface or erases characters.
— 5 —
Handling Compact discs
Playing a CD that is dirty, scratched
or warped can cause the sound to
skip and the unit to operate
incorrectly, resulting in worsened
sound quality. Take the following
precautions to prevent your CDs from
getting scratched or damaged.
Storing CDs
Checking New CDs for Burrs
When playing a new CD for the first time,
check that there are not any burrs stuck to
the perimeter of the disc or in the central
hole. CDs with burrs stuck on them may not
load properly or may skip while playing.
Remove burrs using a ballpoint pen or a
similar utensil.
• Do not store CDs in areas exposed to
direct sunlight (such as a car seat or the
dashboard) or other hot places. A CD-R or
CD-RW is more susceptible than a music
CD to damage from high temperatures and
humidity, and in some cases, may become
unusable if left in the car for long periods
of time.
• Remove CDs from the unit when not
listening to them for a while, and put them
back in their cases. Do not pile up CDs
that are removed from their cases or prop
them against something.
Handling CDs
• Do not touch the recorded side of the CD
(the side opposite the label) when holding
it.
Burrs
Burrs
Cleaning CDs
If a CD has gotten dirty, wipe it off gently
using a commercially available cleaning cloth
or a soft cotton cloth, starting from the
center of the disc and moving outward. Do
not clean CDs with conventional record
cleaners, anti-static formulas, or chemicals
such as paint thinner or benzene.
• The reflective film on a CD-R or a CD-RW is
more fragile than that on an ordinary music
CD, and may peel off if scratched. Fingerprints
on a CD-R or CD-RW are also more likely to
cause skipping when the disc is played. For
these reasons, handle the disc very carefully.
Detailed handling instructions will appear on
the CD-R or CD-RW package: read this
information carefully before using the disc.
• Do not stick tape on either side of the CD.
Tape
— 6 —
Do Not Load CD Accessories
Do not use commercially available CD
accessories that can be loaded into the CD
slot, such as stabilizers, protective sheets,
or CD cleaning discs, since they can cause
the unit to malfunction.
Do Not Use Special Shape CDs
• Be sure to use round shape CDs only for
this unit and do not use any special shape
CDs. Use of special shape CDs may cause
the unit to malfunction.
Do Not Use CDs with Sticker on the
Labeled Side
Do not use the CD with the label sticker
stuck on it.
Using such a CD may cause the CD to be
deformed and the sticker to peel off,
resulting in malfunction of the unit.
Removing the CD
Only remove the CD from the machine in a
horizontal direction, holding it flat. You may
damage the surface of the CD if you try
pulling it down as it ejects.
• Be sure to use CDs with disc mark
only for this unit.
•CD-Rs and CD-RWs which have not
undergone finalization processing cannot
be played. (For more information on
finalization processing, refer to the manual
for your CD-R/CD-RW writing software or
CD-R/CD-RW recorder.) Additionally,
depending on the recording status, it may
prove impossible to play certain CDs
recorded on CD-R or CD-RW.
— 7 —
General features
(KDC-X917/X817/9017)
5
¢
FM
Description about this indicator for these features can be displayed
by setting the Lower Part Display (page 12) to "... + Function
indicator."
SRC/
OFF
ANG
ANG
PTY
DAB
OFF
Power
MENU
AUTO
AME
AUD
LOUD
You can help prevent theft of the unit by reversing the
faceplate so that the control panel cannot be seen, hiding the
unit, and shutting off the audio.
DISP
NAME
NF
Power ON/OFF:
Q
DISP
CLK
ATT/
LOUD
AM/
NF
When you turn your vehicle's ignition on, the unit's power will
also turn on, with the faceplate reversing to show the control
panel.
4
5
When you turn your vehicle's ignition off, the faceplate will
reverse to hide the control panel after a period of time which
you have set in the "Time setting for removing the faceplate" in
the menu. The unit's power will turn off.
Alternatively, you can remove the faceplate during that period.
For details, refer to the "Removing the faceplate" (page 14).
KDC-X917/X817/9017
NOTE
• When the moving faceplate is hit by an object, it will stop and
return to its original state. Remove the object and repeat the
action.
• The status of the security code function (page 34) is display
whenever the power is switched on.
"CODE ON" : Security code has been registered
"CODE OFF" : Security code has not been registered
LOUD indicator
KDC-X717
2CAUTION
Using the Unit in Vehicles with Covered Consoles
• Make sure the console is uncovered while the faceplate is
reversed.
• Do not exert any excess force on the movable parts of the unit,
including the faceplate, as it can cause failure in the unit’s
mechanism.
LOUD indicator
— 8 —
Selecting standby mode:
Volume
Press the SRC button repeatedly and switch to "ALL OFF" .
When "ALL OFF" is displayed, the standby mode is activated.
The standby mode turns all functions off while leaving the
power to the unit on. Use this mode when you want to have
the display illuminated but don't want to listen to anything.
Increasing Volume:
Press the L button to turn up the volume.
Decreasing Volume:
Press the M button to turn down the volume.
NOTE
• The mode switches to the next mode from any mode which
cannot be used.
• The external disc control mode will differ depending on the unit
that is connected.
• To enable the selection of External disc control mode 2/AUX
mode, you should connect optional switching adapter KCA-
S210A (which allows you to select both External disc control
mode 2 and AUX mode) or CD changer (KDC-CPS87, KDC-
CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) or
switching adapter CA-C1AX (which allows you to select AUX
mode only).
During the AUX mode, "AUX" (or AUX-name display) will show
in the display. When the CA-C1AX is being used, the AUX
Mode will replace the External Disc Control Mode.
Attenuator
This function allows you to turn down the volume quickly.
Turning Attenuator On/Off:
Press the ATT button to switch the attenuator on and off.
When the attenuator is off, the volume returns to the original
level.
NOTE
Turning the volume up, or turning it all the way down deactivates
the attenuator function.
NOTE
Selecting AUX-name display
Pressing the DISP button for at least two seconds during the
AUX mode, AUX-name display is blinked for AUX-name selection
mode.
Pressing 4 or ¢ button during this mode allows you to select
"AUX" , "TV" , "VCP" , "GAME" or "PORTABLE" in the AUX mode.
The AUX-name selection mode can be exited by pressing the
DISP button or doing nothing for 10 seconds.
Switching Modes
Switching Modes:
Each time you press the SRC (source) button, the mode
switches as follows:
M
Tuner mode
M
CD mode
M
External disc control mode 1
M
External disc control mode 2 / AUX mode
M
Standby mode
— 9 —
General features
Note that some of these parameters cannot be controlled by the
audio control setting feature. (KDC-9017)
Their setting values are different depending on the setting of the
speaker and woofer setting mode.
Loudness
This function amplifies low and high tones when the volume is
turned down.
The LOUD indicator lights up when the loudness function is
on.
Turning Loudness On/Off:
Press the LOUD button for at least one second to switch the
loudness on and off.
NOTE
Speaker & Woofer setting
Speaker setting allows the System Q settings to be fine-tuned
The loudness function does not affect non-fading pre-out.
according to the type of speakers.
Woofer setting allows for Network configuration according to
the type of subwoofers.
1 Press the SRC button repeatedly to select the standby mode.
System Q
"ALL OFF" is displayed when the standby mode is selected.
You can recall the best audio setting preset for different types
of the music.
2 Press the Q button to enter the speaker setting mode.
3 Each time you press the FM/AM button, the mode switches as
Switching the Preset Sound Setting:
Each time you press the Q button, the preset sound setting
switches as follows:
follows:
Speaker setting mode
Scan of Flat – Easy
Easy
Jazz
Pops
Woofer setting mode (KDC-X917/X817/X717 only)
(Default setting)
User memory*
*User memory:
4 •In speaker setting mode
Flat
The unit returns to the state
adjusted the last time with
the audio control setting feature.
Top 40
Press either the 4 or ¢ button to select the type of
speaker. The setting switches as follows.
Off ("Speaker Setting OFF") /
Rock
For 6/6x9 in. speaker (Speaker Setting 6 9/6 inch") /
For 5/4 in. speaker ("Speaker Setting 5/4 inch")/
For the OEM speaker ("Speaker Setting O.E.M.")
• In woofer setting mode (KDC-X917/X817/X717 only)
Press either the 4 or ¢ button to select the type of Sub
woofer. The setting switches as follows.
NOTE
*
The System Q function changes the values of the following
sound quality parameters:
Bass center frequency, bass level, bass quality factor, bass
extend, middle center frequency, middle level, middle quality
factor, treble center frequency, treble level, non-fading level,
high-pass filter frequency for front output, high-pass filter
frequency for rear output, and low-pass filter frequency for non-
fading output.
"Woofer OFF" / "12in type A" / "10in type A" / "12in type B" /
"10in type B" / "12in type C" / "10in type C" / "8inch" / "12in
type D" / "10in type D"
— 10 —
In Source mode:
Demonstration
5 Press the Q button to end the speaker setting mode and
woofer setting mode.
NOTE
• Speaker setting function allows for tuning of bass, middle and
treble.
• Woofer setting allows for tuing of high-pass filter frequency,
low-pass filter frequency and non-fading level.
Spectrum Analyzer 1
Spectrum Analyzer 2
Spectrum Analyzer 3
Spectrum Analyzer 4 (KDC-X917/X817/9017)/
Each source display+ Graphic (KDC-X717)
Faceplate Angle Adjustment
You can adjust the faceplate angle for easy viewing.
In Stand by mode:
Sliding the faceplate:
Demonstration
Press the ANG button for at least one second.
Date + Clock + Function indicator
"ALL OFF"
NOTE
Please see the menu settings about selecting the display mode.
For details refer to the Switching Display Mode page for the
menu settings. (page 33)
NOTE
Do not apply excessive force to the faceplate under setting 2.
Switching Full-Screen Display
This function switches the type of information on the display
in the full screen display mode.
Each time you press the CLK button, the full screen display
changes as follows:
— 11 —
General features
• If you try to display the name of a disc that doesn't have one,
"NO NAME" is displayed instead.
• When there is an attempt to display the title of a disc for
which the disc title/track title has not been recorded, "NO
TEXT" is displayed for CD and "NO TITLE/NO NAME" is
displayed for MD.
Switching the Upper Part Display
This function switches the type of information on the upper
part display when the display mode is vertical division display.
Each time you press the DISP button, the upper part display
changes as follows:
• If you attempt to display disc title/track title when connecting
the CD changer not supported for CD text feature, caution
messages such as "NO TEXT" or "Reading" may be displayed.
• Depending on the type of characters of the CD Text, some
characters may not be displayable.
In Tuner mode:
Station frequency
SNPS name (only when being preset) /
Program Service name
(only during RDS station reception) (KDC-X917/X817 only)
NOTE
• Please see the menu settings about selecting the display mode.
For details refer to the Switching Display Mode page for the
menu settings. (page 33)
• The same items cannot be selected for both the upper part and
the lower part.
Radio text
(only during RDS station reception) (KDC-X917/X817 only)
NOTE
If the RDS station currently tuned to is transmitting no text
while the Radio Text Display mode is turned on, "NO TEXT"
will appear in the display. While awaiting reception, "Waiting"
will be displayed.
Switching the Lower Part Display
This function switches the type of information on the lower
part display when the display mode is vertical division display.
2WARNING
To prevent accidents, drivers should not look at the display
while on the road.
Each time you press the CLK button, the lower part display
changes as follows:
In Tuner mode:
In CD/External disc control mode:
Spectrum Analyzer1
Track Time
Spectrum Analyzer2 + Clock
Disc name (DNPS)(only when being preset)
Spectrum Analyzer2 + Graphic (KDC-X717 only)
Graphic + Clock (KDC-X717 only)
Disc Title (Units featuring CD text/MD only)
Track Title (Units featuring CD text/MD only)
Date + Function indicator (KDC-X917/X817/9017)/
Date (KDC-X717)
NOTE
Radio text + Function indicator
(only during RDS station reception) (KDC-X917/X817 only)
• You can give names to discs through the presetting disc
name function (page 30).
Note that depending on the unit, display may not be possible.
— 12 —
NOTE
NOTE
If the RDS station currently tuned to is transmitting no text
while the Radio Text Display mode is turned on, "NO TEXT"
will appear in the display. While awaiting reception, "Waiting"
will be displayed.
• You can give names to discs through the presetting disc
name function (page 30).
Note that depending on the unit, display may not be
possible.
• If you try to display the name of a disc that doesn't have
one, "NO NAME" is displayed instead.
• When there is an attempt to display the title of a disc for
which the disc title/track title has not been recorded, "NO
TEXT" is displayed for CD and "NO TITLE/NO NAME" is
displayed for MD.
2 WARNING
To prevent accidents, drivers should not look at the display
while on the road.
In CD/External disc control mode:
• If you attempt to display disc title/track title when
connecting the CD changer not supported for CD text
feature, caution messages such as "NO TEXT" or "Reading"
may be displayed.
Spectrum Analyzer1
Spectrum Analyzer2 + Clock
• Depending on the type of characters of the CD Text, some
characters may not be displayable.
Spectrum Analyzer2 + Graphic (KDC-X717 only)
Graphic + Clock (KDC-X717 only)
NOTE
Date + Function indicator (KDC-X917/X817/9017)/
Date (KDC-X717)
• Please see the menu settings about selecting the display mode.
For details refer to the Switching Display Mode page for the
menu settings. (page 33)
• The same items cannot be selected for both the upper part and
the lower part.
Disc name (DNPS)* + Function indicator (KDC-X917/X817/9017)/
Disc name (DNPS)* (KDC-X717)
Disc Title** + Function indicator (KDC-X917/X817/9017)/
Disc Title** (KDC-X717)
Track Title** + Function indicator (KDC-X917/X817/9017)/
Track Title** (KDC-X717)
*
(only when being preset)
** (Units featuring CD text/MD only)
— 13 —
General features
Forced Closing
Removing the Faceplate
This function prevents tampering with the unit your car is
being serviced etc.
The faceplate can be detached from the unit, helping to deter
theft.
Hiding the unit with the ignition turned on (forced closing):
Press the SRC button for at least one second.
Removing the faceplate:
1
Choose the way from among the following and open the
The faceplate will slide open. When the period of time which
you have set in the "Time setting for removing the faceplate" in
the menu has passed, the faceplate automatically reverses to
hide the control panel. However, you can remove the faceplate
during that period. For details, refer to the "Removing the
faceplate" (page 14).
faceplate.
Turn the ignition off, press the SRC button for at least one
second when the control panel has been hidden.
2 Holding the center part of the faceplate, pull it out during the
period which you have set in the "Time setting for removing
the faceplate" (page 38) in the menu.
NOTE
The faceplate bracket will automatically close.
• When the closing faceplate is hit by an object, the unit will turn
off without the faceplate closing all the way. Remove the object
and press the SRC button to turn the unit back on, then turn it
off again to have it close properly.
• Do not try to press the buttons on the control panel as the
faceplate is moving, as excessive force may damage the unit.
• During the forced closing of the unit (i.e., having the unit left
closed while ignition is turned on), the faceplate will not open
no matter how often the ignition is turned on or off.
2CAUTION
You can prevent tampering of the unit when letting someone
else drive your car by keeping it closed this way.
• When removing the faceplate, pull it out only when it is fully
open. The detachment of the faceplate while it is moving might
result in damage to the unit.
• Do not apply excessive force to the faceplate bracket without
attaching the faceplate. Doing so will cause the faceplate
bracket to be deformed.
To cancel the forced closing of unit and open control panel:
Press the left part at the upper side of the faceplate.
The faceplate will open and show the control panel.
• Do not touch the connector on the faceplate bracket after
removing the faceplate. Touching the connector may cause
damage to the unit.
NOTE
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts. For that reason, keep the faceplate
in its special storage case while detached.
• Do not expose the faceplate or its storage case to direct
sunlight or excessive heat or humidity. Also avoid places with
too much dust or the possibility of water splashing.
— 14 —
Audio control features
Reattaching the Faceplate:
¢
1 Hold the faceplate so that the control panel faces the front
toward you and set the left side of the faceplate in the
faceplate bracket.
FM
2CAUTION
Do not set the right side of the faceplate in the faceplate bracket
first, when reattaching the faceplate. Doing so may cause the
connector on the faceplate bracket to malfunction.
ANG
PTY
DAB
OFF
MENU
AUTO
AME
AUD
LOUD
DISP
NF
NAME
2 Press the right side of the faceplate until it locks.
AM
AUD
4
KDC-X917/X817/9017
Selecting mode
Setting value
Function of the KDC-X917/KDC-X817/KDC-X717
Non-Fading Output
You can turn the non-fading output on and off.
Turning non-fading output On/Off :
Press the NF button for at least one second to set the function
ON or OFF.
"NF ON" is displayed when the non-fading output is set ON.
KDC-X717
Selecting mode
Setting value
— 15 —
Audio control features
Function of the KDC-X917/KDC-X817/KDC-X717
Audio Control Setting
Adjust various parameters of sound quality.
Bass Center Frequency
Adjust the center frequency of the bass.
1 Press the AUD button for at least one second to enter the
Display and setting:
control mode.
"Bass FRQ" : 60 / 70 / 80 / 100 (Only when the bass quality
factor is set to 1.00, 1.25 or 1.50) / 150 (Only
when the bass quality factor is set to 2.00) Hz.
2 Selecting mode
Press either the FM or AM button.
Each time the button is pressed, the adjustment mode will
change.
Please refer to the following for the contents of the
adjustment modes.
NOTE
Bass Level
Adjust the bass level.
Source tone memory
Each source ( tape, CD, MD, FM, AM and disc changer ) has its
own memory in which to store the bass, middle, treble and N-F
level settings. (N-F level : KDC-X917/X817/X717 only)
The settings made for a particular source are recalled
automatically whenever you use that source ( for example, FM
mode uses the tone settings made for FM, AM for AM, etc.).
Display and setting:
"Bass" : - 8 – + 8
3 Adjust each mode
Press the 4/¢ button.
Function of the KDC-X917/KDC-X817/KDC-X717
Bass Quality Factor
Adjust the Bass quality factor.
Please refer to the following for the adjusting values.
4 Press the AUD button to end the control mode.
NOTE
Display and setting:
• Determining the parameters in the audio control setting would
clear all the adjustments made in the System Q and they are
replaced with the values in the audio control setting.
• The following parameters can be set when the System Q
function on the menu settings is ON.
"Bass Q" : 1.00 / 1.25 / 1.50 / 2.00
Bass center frequency, bass quality factor, bass extend, middle
center frequency, middle quality factor, and treble center
frequency.
Function of the KDC-X917/KDC-X817/KDC-X717
Bass Extend
Switch the Bass Extend mode on/off.
Display and setting:
"Bass EXT" : ON / OFF (When the bass extend mode is set to
on, low frequency response is extended by 20%.)
— 16 —
Function of the KDC-X917/KDC-X817/KDC-X717
Treble Level
Adjust the treble level.
Middle Center Frequency
Adjust the center frequency of the middle.
Display and setting:
Display and setting:
"TRE" : - 8 – + 8
"MID FRQ" : 0.5 / 1.0 / 1.5 / 2.0 kHz.
Balance Level
Adjust the balance level.
Middle Level
Adjust the middle level.
Display and setting:
"Balance" : Left 15 – Right 15
Display and setting:
"MID" : - 8 – + 8
Fader Level
Adjust the fader level.
Function of the KDC-X917/KDC-X817/KDC-X717
Display and setting:
Middle Quality Factor
Adjust the middle quality factor.
"Fader" : Rear 15 – Front 15
Display and setting:
"Middle Q" : 1.0 / 2.0
Function of the KDC-X917/KDC-X817/KDC-X717
Non-Fading Level
Adjust the Non-fading output level.
Function of the KDC-X917/KDC-X817/KDC-X717
Display and setting:
Treble Center Frequency
Adjust the center frequency of the treble.
"NF Level" : - 15 – + 15
NOTE
Display and setting:
• This mode is available only when the non-fading output function
is set to on.
• Not available during the Dual zone system is on.
"TRE FRQ" : 10.0 / 12.5 / 15.0 / 17.5 kHz
— 17 —
Audio control features
Function of the KDC-X917/KDC-X817/KDC-X717
NOTE
High-pass Filter Frequency for Front Output
Adjust the frequency of the High-pass filter for front output.
• This mode is available only when the non-fading output function
is set to on.
• Not available during the Dual zone system is on.
Display and setting:
"HPF Front" : Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /
150Hz / 180Hz / 220Hz
Function of the KDC-X917/KDC-X817/KDC-X717
Phase for Non-Fading Output
Adjust the phase for Non-Fading output.
NOTE
You can separately set the high-pass filter for front and rear
output, including preouts. The high-pass filter does not affect the
non-fading preout.
Display and setting:
"NF Phase" : Normal (0°) / Reverse (180°)
NOTE
• This mode is available only when the non-fading output function
is set to on.
• Not available during the Dual zone system is on.
Function of the KDC-X917/KDC-X817/KDC-X717
High-pass Filter Frequency for Rear Output
Adjust the frequency of the High-pass filter for rear output.
Display and setting:
"HPF Rear" : Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /
150Hz / 180Hz / 220Hz
NOTE
Volume Offset
Set the sound level of the each source selected by adjusting
the level difference between the basic sound level and the
required level.
You can separately set the high-pass filter for front and rear
output, including preouts. The high-pass filter does not affect the
non-fading preout.
Display and setting:
"Volume Offset"/"VOL Offset" : - 8 –
0
Function of the KDC-X917/KDC-X817/KDC-X717
Low-pass Filter Frequency for Non-Fading Output
Adjust the frequency of the Low-pass filter for Non-Fading
output.
Display and setting:
"LPF NF" : 50 Hz / 80 Hz / 120 Hz / Through
— 18 —
Tuner features
¢
FM
38
SRC
ANG
PTY
DAB
OFF
AUD
MENU
AUTO
AME
LOUD
DISP
NAME
NF
#1-6
AM
4
NAME
AUTO/
AME
KDC-X917/X817/9017
Preset station number
Frequency
ST indicator
Band display
KDC-X717
Frequency
Preset station number
AUTO indicator
Band display
ST indicator
— 19 —
Tuner features
• Preset station seek tuning
(KDC-X917/X817/9017)
Press the ¢ button to move to the next preset station (i.e.,
the one with the next highest number), and the 4 button to
move to the last preset station (i.e., the one with the next
lowest number).
Description about this indicator for these features can be displayed
by setting the Lower Part Display (page 12) to "... + Function
indicator."
• Manual Tuning
Press the ¢ button to increase the frequency by one step.
Press the 4 button to decrease the frequency by one step.
NOTE
Tuning
You can choose from three tuning modes: auto seek, preset
station seek, and manual.
The AUTO 1 indicator lights up when auto seek tuning is
selected, and the AUTO 2 indicator lights when preset station
seek tuning is selected. (KDC-X717 only)
The ST indicator lights up when stereo broadcasts are being
received.
Selecting Tuning Mode:
Station Preset Memory
Store the frequency of a station. You can then recall that
station with a single touch of a button.
Press the AUTO button.
Each time you press the AUTO button, the mode switches as
follows.
M
1 Select the band/station that you want to have stored.
Auto 1 (Auto Seek Tuning)
M
2 Press the button (#1-6) that you want to use for the station, for
at least two seconds.
Auto 2 (Preset Station Seek Tuning)
M
The button number blinks once in the display to indicate that
the data has been stored.
Manual (Manual Tuning)
Recalling a Preset Station:
Tuning:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
NOTE
1 Press the SRC (source) button repeatedly to select the tuner
mode. "TUNER" is displayed when the tuner mode has been
selected.
You can store six stations in each of the FM1, FM2, FM3, and
AM bands.
2 Press either the FM or AM button to select the band.
Each time you press the FM button, the band switches
between the FM1, FM2 and FM3 (which are used for groups
of preset stations).
Press the AM button to select the AM band.
3 • Auto Seek Tuning
Auto Memory Entry
Press the ¢ button to seek higher frequencies.
Press the 4 button to seek lower frequencies.
You can automatically store all the receivable frequencies in
the band currently being listened to, and then recall them with
the touch of a button later. This function is especially useful
when you are travelling and do not know what stations are
available. Up to six frequencies can be stored this way.
— 20 —
1 Select the band for auto memory entry.
2 Press the AME button for at least two seconds to start auto
memory entry.
The numbers of the preset station buttons are shown in order.
When all the stations in a certain band are stored in the preset
memory, the auto memory entry stops. The tuner then plays
the last station received.
Recalling a Preset Station:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
Function of the KDC-X917/KDC-X817/KDC-X717
Direct Access Tuning
(Function of remote)
When you know the frequency of the station that you want to
listen to, you can input it directly for quick access.
1 Select the band by pressing the FM or AM button.
2 Press the DIRECT button.
"----" is displayed for 10 seconds.
If you make no input in the 10-second period, direct access
tuning is automatically canceled.
3 Enter the frequency of the desired station.
If you want to listen to an FM station at 92.1 MHz, for
example, press 0, 9, 2, and 1.
If you want to listen to an AM station at 810 kHz, for example,
press 0, 8, 1, and 0.
NOTE
• You cannot enter frequencies above or below what a band can
receive.
• FM frequencies can only be input in 0.1 MHz steps, and not
0.01 MHz steps.
Canceling Direct Access Tuning:
Press the DIRECT button again.
— 21 —
Tuner features
Station Name Preset (SNPS)
Character
Button to press
# Times pressed
You can assign names to radio stations with the Station Preset
Memory. Up to 32 FM stations and 16 AM stations can be
assigned names.
#3
#2
#6
#2
#3
1
1
2
3
2
“D”
“A”
“N”
“C”
“E”
1 Adjust the frequency to the station whose name you want to
enter.
2 Press the NAME button for at least two seconds.
"NAME SET" is displayed once the station name preset mode
is entered.
5 Continue steps 3 and 4 until all the characters are chosen for
The cursor will blink in the position where letters are entered.
the name.
3 Press either the 4 or ¢ button to move the cursor to the
desired position.
NOTE
You can enter up to eight characters for each name.
The 4 button moves the cursor to the left, and the ¢
button to the right.
6 Assigning Names
You can also move the cursor left or right by pressing the 4
or ¢ buttons, respectively, on the remote.
Press the NAME button on the unit or the OK button on the
remote.
The name of the station is stored in memory, and the Station
Name Preset mode ends.
Also, if you make no input for 10 seconds, the name will be
stored up to the point that you have entered, and the mode
ends.
4 Each time the 38 button is pressed, the characters to be
entered change as listed below.
Press the FM or AM button to display the desired character.
Characters that can be displayed are as follows.
NOTE
Alphabet (upper case): A ~ Z
• You can assign names to up to 32 FM stations and 16 AM
stations.
• All the station names will be erased if you press the Reset
button.
Alphabet (lower case): a ~ z
Numerals and symbols: 0~9 @ ” ‘ ` % & * + - = , . / \ < > [ ]
• If you want to change the name of a station, first display the
name of the station (following steps 1 and 2 above), then
change the letter(s) that you want by following steps 3 and 4.
Special characters: á à é è íìó ò ú ù Ñ Ç ® ß ‹fl
îï ô ö û ü ñ ç © Æ › fi
â ä ê ë
NOTE
Direct Alphabet Input
(Function of remote with number/letter entry buttons :
KDC-X917/X817/X717 only)
Direct input can be made of letters (alphabetical) with the letter
entry buttons on the remote.
Example: Use the following table to enter the name "DANCE”.
— 22 —
RDS features
Function of the KDC-X917/KDC-X817
Station Name Preset Play (SNPP)
¢
(Function of Remote)
PTY
FM
You can search for the station for any station if its name has
been preset using Station Name Preset.
1 Press the DNPP button on the remote.
ANG
PTY
DAB
"SNPP" will be displayed once the station name preset play
mode is entered.
OFF
MENU
AUTO
AME
AUD
LOUD
The names of the stations stored in the band currently listened
to are displayed in the following order for five seconds each:
DISP
NAME
NF
= FM1 Ô FM2 Ô FM3 Ô AM +
Each time you press the ¢ button, the station display
switches in the forward direction.
CLK
DISP/
NAME
AM
#1-6
4
Each time you press the 4 button, the station display
switches in the reverse direction.
Stations whose names have not been stored will be displayed
as frequencies.
The program service name will appear for RDS stations. (KDC-
X917/X817 only)
NOTE
Program Service name
Changing the Displayed Band
Pressing the FM button switches between the FM1, FM2, FM3
and AM displays, in that order.
Pressing the AM button switches between the displays in the
reverse direction.
2 Once the name is displayed for the station you want to
listen to
Press the OK button.
Reception starts of the displayed station, and the station name
preset play mode ends.
Radio text
RDS indicator
TI indicator
Canceling mode during input:
Press the DNPP button.
The station name preset play mode is canceled.
— 23 —
RDS features
Function of the KDC-X917/KDC-X817
To scroll manually:
Description about this indicator for these features can be displayed
by setting the Lower Part Display (page 12) to "... + Function
indicator."
1 Press the DISP button to display radio text on the upper part
display.
2 Pressing the DISP button for at least one second results in one
scrolling display of the text.
NOTE
• Please see the menu settings (page 33) about switching
between manual scrolling and automatic scrolling.
• You can scroll text when the vertical division display mode has
been selected by the switching display mode function.
For details refer to the Switching Display Mode page for the
menu settings. (page 33)
RDS (Radio Data System)
RDS is a service used by radio stations to transmit data
outside normal radio broadcast signals.
When an RDS station is received, you can immediately find
out what kind of data is being transmitted by looking at the
program service name, which appears in the display after the
frequency.
The RDS indicator turns on when an RDS station is being
received.
Program Type (PTY) Function
Conduct auto seek tuning only on those stations with selected
kinds of programs.
Alarm
1 Press the PTY button.
When an emergency transmission (announcing disasters, etc.)
is made, the current function will be interrupted to allow the
warning to be received under the following conditions:
during tuner reception, or when the Traffic Information
function is turned on.
"PTY Select" is displayed once the program type selection
mode is entered.
NOTE
You cannot use this function while the traffic bulletin is received.
2 Select the type of program to be received
• Press either the FM or AM buttons repeatedly to select the
type of program you want to listen to.
The selection includes:
Radio Text Scroll
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
Speech
Music
(All Speech)
(All Music)
(News)
1. News
2. Information
3. Sports
4. Talk
(Information)
(Sports)
To scroll automatically:
(Talk)
(Rock)
(Classic Rock)
(Adult Hits)
Press the DISP or CLK button to display radio text on the
upper or lower part display.
5. Rock
6. Classic Rock
7. Adult Hits
The display of the text will be scrolled repeatedly.
— 24 —
8. Soft Rock
9. Top 40
10. Country
11. Oldies
12. Soft
(Soft Rock)
(Top 40)
NOTE
If no program can be found, "NO PTY" is displayed.
If you want to select another type of program, repeat steps 2 and
3 above.
(Country)
(Oldies)
(Soft)
(Nostalgia)
(Jazz)
(Classical)
(Rhythm and Blues)
(Soft R & B)
(Foreign Language)
Switching to Other Stations with the Same Type of Program:
When "PTY Found" is displayed, perform auto seek tuning.
The tuner scans for another station with the same type of
program.
13. Nostalgia
14. Jazz
15. Classical
16. R&B
17. Soft R&B
18. Language
Canceling Program Type Function During Its Operation:
Press the PTY button.
19. Religious Music (Religious Music)
Confirming Program Type:
20. Religious Talk
21. Personality
22. Public
(Religious Talk)
(Personality)
(Public)
(College)
(Weather)
Press the DISP button.
The program type of the station currently tuned to will be
displayed for five seconds. During that time, "Entry" will blink in
the display.
23. College
24. Weather
(Speech.....1~4, 18, 20~24, Music.....5~17, 19)
• You can select the type of program directly by pressing a
preset button. The buttons are factory-set to the following
type of programs:
NOTE
If you tune to frequencies for which no program type has been
stored, "No Entry" will be displayed.
1. Music
4. Sports
2. Speech
5. Classical
3. News
6. Jazz
NOTE
Changing the Preset Button Settings for Program Type
Registration of a station as a PTY
You can register a station as a program type.
After selecting the type of program to be stored in a certain
preset button, press that button for at least two seconds.
The previously stored data for that button are erased and the
new program type is stored.
To register a non-RDS station as a program type:
1 Tune your radio to the non-RDS station that you want to
3 Seeking the Selected Program Type
Press the 4 or ¢ button to make a seek of frequencies
with your selected type of program.
register as the program type.
2 Press the PTY button to enter the program type selection
The display blinks and the seek starts.
mode.
If your selected type of program is found, the name or the
frequency of the station is displayed and the station is tuned
into.
"PTY Found" is displayed for about 30 seconds.
If you make no key input in 30 seconds, the PTY selection
mode will turn off automatically.
3 Press the FM/AM button to select the program type you want
to register. Follow the instructions in 2 to enter the program
type selection mode.
4 Press the NAME button for at least two seconds.
The station will be registered as a program type, allowing it to
be the target of frequency seeks just as RDS stations are.
5 Press the PTY button to end the program type selection mode.
— 25 —
CD/External disc control features
(KDC-X917/X817/9017)
¢
38
Description about this indicator for these features can be displayed
by setting the Lower Part Display (page 12) to "... + Function
indicator."
DISC+
0
SRC
Playing CDs
ANG
PTY
DAB
OFF
AUD
Playing CDs:
MENU
Press the 0(EJECT) button to slide open the faceplate,
showing the CD (insertion) slot. Holding the CD with the
labeled side facing up, insert it in the slot. The faceplate will
close, and the CD will start playing.
AUTO
AME
LOUD
DISP
NAME
NF
The IN indicator will light when a CD has been inserted.
DISC-
CLK
SCAN
REP
M.RDM
DISP/
NAME
Playing CDs Already Inserted:
4
RDM
Press the SRC button repeatedly to select the CD mode.
"CD" is displayed when the CD mode has been selected.
The CD will start playing.
KDC-X917/X817/9017
Disc number Track number
Pausing and Restarting CD Play:
Track time
Press the 38 button to make the disc pause.
Press the same button again to start play again.
Eject:
Press the 0(EJECT) button. The faceplate will slide to eject the
CD.
Press the 0(EJECT) button to close the faceplate.
2CAUTION
Disc title/Track title/DNPS
• Do not attempt to insert a CD into the slot if another one is
already there.
IN indicator
KDC-X717
• The unit can only play 5 in. CDs. If you insert a 3 in. CD, it will
get stuck inside and can cause the unit to malfunction.
• When the faceplate has been slid open, it might interfere with
the shift lever or something else. If this happens, pay attention
to safety and move the shift lever or take an appropriate action,
then operate the unit.
Track number
Track time
NOTE
• The sound will be temporarily muted while the faceplate is
moving.
• When you load a CD and eject it right away, the next time you
try to insert the CD may not load. In such a situation, take the
CD out for a moment and then reinsert it.
Disc title/Track title/DNPS
IN indicator
— 26 —
NOTE
Playing Other Disc mode
You cannot use reverse play between tracks depending on the
model being connected. Instead, the reverse play function is
canceled when it reaches the beginning of a track, at which point
normal play will automatically resume.
This function permits the connection of optional players and
the playing of discs other than the loaded CD (in the current
unit).
Playing Discs:
Press the SRC button repeatedly to select the external disc
control mode.
The disc will start playing.
NOTE
Track Search
Search forward or backward through the tracks on the disc
until you reach the one that you want to listen to.
The external disc control mode will differ, depending on the unit
that is connected.
Mode Display Examples
• "CD2" ...when a CD player is connected
• "CD-CH"/"MD-CH"/"DISC" ...when a disc changer is connected
• "CD-CH1"/"MD-CH1"/"DISC1" , "CD-CH2"/"MD-CH2"/"DISC2"
...when two disc changers are connected
Making a Reverse Track Search:
Press the 4 button to display the desired track number.
Press once to search back to the beginning of the current
track, twice to search back to the beginning of the previous
track, and so forth.
Pausing and Restarting Disc Play:
Press the 38 button to make the disc pause.
Press the same button again to start play again.
Play starts at the beginning of the displayed track number.
NOTE
(For disc changers)
NOTE
Pressing the 4 button while listening to track 1 will only search
back to the beginning of that track. The reverse search is not
"recycled" to the last track on the disc.
When one disc has finished playing its last track, the next disc in
the changer will start playing. When the last disc in the changer
has finished, the player will return to the first disc and start
playing it.
Making a Forward Track Search:
Press the ¢ button to display the desired track number.
Press once to fast forward to the next track, twice to fast
forward to the track after that, and so forth.
Play starts at the beginning of the displayed track number.
NOTE
(For disc changers)
You cannot make a forward track search when listening to the
last track on a disc.
Fast Forwarding and Reversing Disc Play
Fast Forwarding Disc Play:
Hold down on the ¢ button.
Release your finger to play the disc at that point.
Reversing Disc Play:
Hold down on the 4 button.
Release your finger to play the disc at the point.
— 27 —
CD/External disc control features
NOTE
Disc Search
(Function of disc changers)
Repeat play is canceled when you eject the disc.
Search forward or backward through the discs in a disc
changer.
Making a Reverse Disc Search:
Track Scan
Press the DISC– button to display the desired disc number.
Each time the button is pressed, the displayed disc number
decreases by one.
Successively play the beginning of each track on a disc until
you find the track that you want to listen to.
Play starts at the beginning of the displayed disc.
Starting the Track Scan:
Making a Forward Disc Search:
Press the SCAN button. "Scan ON" is displayed and the first 10
seconds of each track will be played, in order.
The track number currently being heard blinks in the display.
Press the DISC+ button to display the desired disc number.
Each time the button is pressed, the displayed disc number
increases by one.
Stopping to Listen to the Track Being Scanned:
Press the 38 or SCAN button again to stop the scan and keep
on listening to a track normally.
Play starts at the beginning of the displayed disc.
NOTE
"Load" is displayed when discs are being exchanged on the disc
changer.
NOTE
• The track scan function is canceled when you eject the disc.
• The track scan function only scans each track on a disc once.
Track / Disc Repeat
Repeat playing the track or the disc currently being listened to.
Random Play
Play all the tracks on the current disc in random order.
Turning Repeat Play On/Off:
1 Press the RDM button to switch random play on and off.
"Random ON" is displayed when random play is turned on.
The track number will change over and over in the display as
the next track is being selected.
Press the REP button to switch repeat track/disc play on and
off as follows:
M
Track Repeat ON
When the track has been selected, play will begin.
The selected track number blinks in the display as it is being
played.
M
Disc Repeat ON (Function of disc changers)
M
Repeat OFF
NOTE
(For disc changers)
When all the tracks on a certain disc have been played using
random play, the next disc on the changer will start playing using
the same function.
"Track Repeat ON"/"Repeat ON" is displayed and the track
number blinks in the display when track repeat is on.
"Disc Repeat ON" is displayed and the disc number blinks in
the display when disc repeat is on.
2 To change the track being heard, press the ¢ button.
Another track will be selected and played.
— 28 —
NOTE
Random play is canceled when you eject the disc.
Text Scroll
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
To scroll automatically:
Press the DISP or CLK button to display the disc or track title
on the upper or lower part display.
The display of the text will be scrolled repeatedly.
To scroll manually:
1 Press the DISP button to display the disc or track title on the
upper part display.
2 Pressing the DISP button for at least one second results in one
scrolling display of the titles.
NOTE
• Please see the menu settings (page 33) about switching
between manual scrolling and automatic scrolling.
• You can scroll text when the vertical division display mode has
been selected by the switching display mode function.
For details refer to the Switching Display Mode page for the
menu settings. (page 33)
— 29 —
CD/External disc control features
NOTE
Presetting Disc Names (DNPS)
Direct Alphabet Input
(Function of remote with number/letter entry buttons :
KDC-X917/X817/X717 only)
If the disc changers that were manufactured and sold after 1997
(except for KDC-C560) are connected, you can directly input
letters using the number/letter entry buttons on the remote.
Example: Use the following table to enter the name "DANCE".
Store the names of discs to be displayed when played.
1 Play the disc whose name you want to preset.
NOTE
• This function is not available for disc changers that do not
feature the Disc Name Preset function.
• The Disc Name Preset function cannot be used during the
Magazine random play as well as while a disc title or track title
is displayed.
Character
Button to press
# Times pressed
#3
#2
#6
#2
#3
1
1
2
3
2
“D”
“A”
“N”
“C”
“E”
2 Press the NAME button for at least two seconds.
"NAME SET" is displayed and the disc name preset mode is
entered.
The cursor blinks in the position where character input can be
made.
3 Press either the 4 or ¢ button to move the cursor to the
desired position.
5 Continue steps 3 and 4 until all the characters are chosen for
The 4 button moves the cursor to the left, and the ¢
button to the right.
the name.
NOTE
You can also move the cursor left or right by pressing the 4
or ¢ buttons, respectively, on the remote.
You can enter up to 12 characters for each name.
4 Each press of the 38 button results in the type of characters
that are to be entered changing between alphabet and
numerals/symbols.
6 Press either the NAME button on the main unit or the OK
button on the remote.
The disc name is stored and the disc name preset mode is
canceled.
Press the DISC+ or DISC– button to display the desired
character.
If you make no entry in a 10-second period, the name will be
stored with the characters input so far.
Characters that can be displayed are as follows.
NOTE
Alphabet (upper case): A ~ Z
• The number of discs whose names can be stored will differ
depending on the disc changer that is connected. Please see
your disc changer manual for details.
Alphabet (lower case): a ~ z
Up to 30 CDs can be registered with this unit.
Numerals and symbols: 0~9 @ ” ‘ ` % & * + - = , . / \ < > [ ]
• Discs are identified by their total length and number of tracks. If
another disc happens to have the same specifications as one
that you have already stored a name for, the name will be
displayed for it, too.
Special characters: á à é è íìó ò ú ù Ñ Ç ® ß ‹fl
îï ô ö û ü ñ ç © Æ › fi
â ä ê ë
— 30 —
• If you want to change the name of a disc, repeat steps 1 and 2
to display the name, and then repeat steps 3 and 4 to input the
changes.
• Pressing the reset button erases the disc names stored in this
unit, but does not erase the names stored in a disc changer.
Function of the KDC-X917/KDC-X817/KDC-X717
Direct Track Search
(Function of Remote)
Using the remote, directly input the track number that you
want to listen to.
1 Using the number buttons on the remote, input the number of
the track that you want to listen to.
The selected track number will blink in the display for 10
seconds.
If you make no further input in the 10-second period, the
number entry mode will automatically be canceled.
Magazine Random Play
Play the tracks on all the discs in the disc changer in random
order.
(Function of disc changers)
2 Press either the 4 or ¢ button while the track number is
blinking.
The track starts playing.
1 Press the M.RDM button to switch magazine random play on
and off.
Canceling Direct Track Search While It Is Operating:
Press the 38 button.
"M.Random ON" is displayed when magazine random play is
turned on.
NOTE
You cannot use the direct track search function during random or
magazine-random play.
The disc and track numbers will change over and over in the
display as the next track is being selected.
When the disc/track has been selected, play will begin.
The selected disc/track number blinks in the display as it is
being played.
2 To change the track being heard, press the ¢ button.
Another disc/track will be selected and played.
NOTE
• Magazine random play is canceled when you eject the disc.
• The time needed for random selection depends on the number
of discs loaded in the disc magazine.
— 31 —
CD/External disc control features
Function of the KDC-X917/KDC-X817/KDC-X717
NOTE
Direct Disc Search (Function of disc changers with remote)
Using the remote, directly input the disc number that you
want to listen to.
• This function can only be used in disc changers that were
manufactured or sold as of 1997. Also note that some units
cannot provide a display unless the disc name preset has been
made by the unit that is playing.
• Discs in the disc changer that have never been played before
will appear as "NO ACCESS" when the disc names are
displayed. When you cannot identify a disc because of the "NO
ACCESS" display after inserting a disc magazine, try playing it to
display the disc name. Also note that "NO DISC" will be
displayed when a disc has not been loaded.
1 Using the number buttons on the remote, input the number of
the disc that you want to listen to.
The selected disc number will blink in the display for 10
seconds.
If you make no further input in the 10-second period, the
number entry mode will automatically be canceled.
NOTE
Rapid display (forward / reverse):
Press the DISC+ or DISC– button.
• Input "0" to select disc 10.
Pressing the DISC+ button will rapidly display the preset
• If you input more than two numbers all at once, a search will be
made only of the last number input.
names/disc titles in order.
Pressing the DISC– button will rapidly display the preset
names/disc titles in reverse order.
• You cannot use the direct disc search function during random
play or magazine random play.
2 When the name appears for the disc you want to play
Press the OK button.
2 Press either the DISC+ or DISC– button while the number
inputted is blinking.
The disc whose name is displayed will be recalled, and the disc
name preset play (DNPP) mode will end.
The disc starts playing.
Canceling Direct Disc Search While It Is Operating:
To cancel DNPP mode:
Press the 38 button.
Press the DNPP button.
The disc name preset play (DNPP) mode will be canceled.
Disc Name Preset Play (DNPP)
(Function of Remote)
If you have preset the name of a disc that you want to listen to
in the disc changer, you can look for it by name and start
playing it.
1 Press the DNPP button on the remote.
"DNPP" will appear in the display, and the disc name preset
play mode is entered.
The names of all the discs in the disc changer will appear
successively in the display for five seconds each.
Discs whose names have not been preset will appear as "NO
NAME" in the display.
— 32 —
Menu settings
(KDC-X917/X817/9017)
¢
FM
Description about this indicator for these features can be displayed
by setting the Lower Part Display (page 12) to "... + Function
indicator."
SRC
38
Menu System
AUTO
You can set the defaults for additional functions in the menu
mode. Make a setting for each function, referring to the
following operations.
1 Enter the menu mode
DISP
MENU
AM
#1-6
Press the MENU button for at least one second.
"MENU" is displayed when the menu mode is entered.
The function that you can adjust is indicated with the current
settings displayed.
4
KDC-X917/X817/9017
2 Selecting function to set
Menu display
Press the FM button to search through the functions until you
see the one you want to adjust in the display.
Press the AM button to search through the functions
backward.
Function items change in the order of features that follow in
the menu system.
Example: If you want to switch the setting of the touch sensor
tone function from on to off, first search through the
functions until you see "Beep ON" in the display.
TI indicator
3 Changing setting for currently displayed function
Press either the 4 or ¢ button.
KDC-X717
The setting will change for each function.
Menu display
Example: The setting of the touch sensor tone will switch from
on to off, and "Beep OFF" is displayed.
4 Ending the menu mode
Press the MENU button.
NOTE
Make sure to end the menu mode when finished.
If you fail to end the menu mode, several functions may not
operate properly, including the Traffic Information function and
the Alarm function.
— 33 —
Menu settings
Security Code <In Stand by mode>
When the battery is removed from the unit's power switch,
you cannot turn on the unit again unless the preset security
code is input. This function helps prevent theft.
# Times
pressed
Step
Button to press
Display
1
2
3
4
#1
#2
#3
#4
4
6
2
1
“3”
“5”
“1”
“0”
NOTE
You must follow steps 1 to 8 to be able to use the Security Code
function. Turning off the power during the procedure will
deactivate the security code setting.
Once the security code function has been activated, "Security"
disappears from the MENU system. Note that it will no longer be
possible to cancel this function afterwards.
6 Press the DISP button for at least three seconds.
The security code will be set.
"RE-ENTER" will appear in the display for one second, asking
you to enter the code once again for confirmation. When
"CODE" appears in the display, you can start inputting the
code.
1 Press the SRC button repeatedly to select the standby mode.
"ALL OFF" is displayed when the standby mode is selected.
2 Select the four digits to use in your security code.
NOTE
7 Press the Preset button and input the security code again.
8 Press the DISP button again for at least three seconds.
"APPROVED" will appear in the display, with the security code
function turning on. From this point on, if the unit is
disconnected from the battery, the security code must be
entered the first time that the unit's power is turned on.
"ENTER" and "CODE" will appear in the display, asking you to
input the code.
The four-digit security code is very important, as you will need it
to turn the unit on again when the code security function is on.
Choose the number carefully and do not forget it (write it down
and keep it separately in a safe place).
3 Press the MENU button for at least one second.
"MENU" is displayed first and then "Security" is displayed.
NOTE
4 Press either the 4 or ¢ button for at least one second.
"ENTER" will appear in the display for one second, indicating
the code setting mode has been entered. When "CODE"
appears in the display, you can start inputting the code.
If you input an incorrect security code, the code setting mode
will be canceled automatically. Follow the steps from 4 to 8
above again.
5 Press the preset button and enter the security code that you
have selected in step 2.
If you press the RESET button or remove the battery:
The first time you turn the unit on again, "CODE" will appear in
the display, asking you to input the security code.
Repeat steps 7 and 8 above, and input the security code.
You can start operating the unit again when "APPROVED"
appears in the display.
Example: Use "3510" as the security code.
If you enter the incorrect code, the power will turn off. Enter
the correct code to turn the unit on.
— 34 —
Touch Sensor Tone
Calendar Adjustment
This function produces a beep sound that accompanies button
operation. It can be switched on or off.
Adjust the date for the unit so that you can use the calendar
function.
Display and setting:
Display and setting:
"Beep ON" : Beep setting is on. (Default setting)
"Beep OFF" : Beep setting is off.
1 Select the display "Date Adjust" during the selecting function in
the menu system.
NOTE
2 Press either the 4 or ¢ button for at least one second to
enter the Calendar adjustment mode.
The beep sound is not output from the preout jacks.
The date display will blink.
3 Selecting the item (day, month, or year) to adjust
Press the 4 or ¢ button.
The item blinking in the display can be adjusted.
Manual Time Adjustment
Adjust the time manually.
4 Adjusting the date
Press the FM or AM button.
The item of the date blinking in the display will change.
NOTE
(KDC-X917/X817 only)
This adjustment is available only when the automatic time
adjustment is set to off. (page 36)
5 Press the MENU button to end the Calendar Adjustment
mode.
Display and setting:
1 Select the display "Clock Adjust" during the selecting function
in the menu system.
2 Press either the 4 or ¢ button for at least one second to
enter the Manual time adjustment mode.
The time display will blink.
Calendar Mode
You can set the date formats of the calendar function.
Display and setting:
3 • Adjusting the hours
1 Select the display "Date Mode" during the selecting function in
Press the FM button to advance the hours, or press the AM
button to make the hours go back.
the menu system.
• Adjusting the minutes
Press the ¢ button to advance the minutes, or press the
4 button to make the minutes go back.
2 Press the 4 and ¢ button to select the date format you
want to show in the display.
The sample of the date format for today is displayed.
4 Press the MENU button to end the Manual Time Adjustment
mode.
Exiting the Manual Time Adjustment mode would start the
clock counting.
— 35 —
Menu settings
Memo Mode
Alphabet (upper case): A ~ Z
You can input the text to be displayed and set the date when
that text will appear in the display with the calendar function.
Alphabet (lower case): a ~ z
Display and setting:
Numerals and symbols: 0~9 @ ” ‘ ` % & * + - = , . / \ < > [ ]
1 Select the display "Memo Mode" during the selecting function
in the menu mode.
Special characters: á à é è íìó ò ú ù Ñ Ç ® ß ‹fl
îï ô ö û ü ñ ç © Æ › fi
â ä ê ë
2 Press either the 4 or ¢ button for at least one second to
enter the Memo mode.
The date display will blink.
• Selecting the character
Press the FM and AM button.
3 Selecting the set of the date and text to be displayed
Press the FM and AM button.
8 Press the MENU button to end the Memo Mode.
NOTE
If you want to input a new text, select the blank display.
4 Entering the month or day setting mode
Press the 4 and ¢ button to enter the month or day
setting mode.
• The text you selected automatically appears on the date you set
when the unit’s power is first turned on. (Calendar function)
The DISP button for at least one second scrolls the display
once, regardless of the text scroll setting.
The month display blinks when in month mode, the day display
blinks when in day setting mode.
Pressing a button other than the DISP button will cause the text
to disappear from the display.
5 Changing the month or day
• You can enter up to 32 characters for each text.
• The calendar function can be set up to 30 cases.
• To delete the date and text setting, set both the month and day
of the date to "00" or set all of the text to blanks.
Press the FM and AM button.
6 Entering the text input mode
Press the ¢ button to enter the text input mode.
The cursor blinks in the position where character input can be
made.
7 Inputting / Changing the text
• Moving the cursor
Function of the KDC-X917/KDC-X817
Press the 4 and ¢ button.
• Changing the type of characters
Press the 38 button.
Automatic Time Adjustment
With automatic time adjustment, you can set the clock time
automatically according to time data sent from RDS stations
(after receiving RDS signals for several minutes). You can also
set the time manually if the automatic time adjustment
function is turned off.
Each time the button is pressed, the type of characters
switches as follows.
Display and setting:
"SYNC ON" : Automatic time adjustment
"SYNC OFF" : Manual time adjustment (Default setting)
— 36 —
Adjusting Time Automatically:
Function of the KDC-X917/KDC-X817/KDC-9017
Tune to a RDS station and receive the signal for several
minutes.
Icon/Spectrum analyzer Select
This function permits switching of the spectrum analyzer
The clock will adjust automatically to the local time.
NOTE
display.
Display and setting:
The clock will not adjust automatically if the RDS station tuned to
is not transmitting time data. In such a case, try another RDS
station.
1 Select the display "Icon/Speana Select" during the selecting
function in the menu system.
2 Pressing the 4 or ¢ button switches the Icon/Spectrum
analyzer.
Selectable Illumination
You can switch the color of the button illumination between
Function of the KDC-X917/KDC-X817/KDC-9017
Font Select
You can change the font used on the display.
green and red.
Display and setting:
"Button Color Green"/"Button Green" :
The color of the illumination is green.
"Button Color Red"/"Button Red" :
The color of the illumination is red.
Display and setting:
1 Select the display "Font Select" during the selecting function in
the menu system.
2 Pressing the 4 or ¢ button switches the font on the
display.
Function of the KDC-X717
Switching Display Mode
You can select the display mode of this unit.
Brightness level adjustment
You can adjust the brightness level of the unit separately
Display and setting:
when your car's light switch has been turned on or off.
"Display Type A" : Divide the display into the upper and lower
parts to separately provide different
information. (Vertical division display) (page
12) (Default setting)
Display and setting:
"Bright 0" – "Bright 10"
NOTE
"Display Type B" : The display will turn on by using only the
upper part of the display and clock.
"Display Type C" : Use the entire display to provide a single
type of information. (Full screen display)
(page 11)
The initial setting value while your car's light switch is turned on
is "5" , and while the light is turned off is "10".
— 37 —
Menu settings
Function of the KDC-X917
Dimmer
You can dim the display.
Built-in Amp Mute Control <In Stand by mode>
Toggles on or off the mute control on the built-in amplifier.
Turning on this control enhances the preout quality.
NOTE
The dimmer function is not available for units if the dimmer wire
is not connected.
Display and setting:
"Builtin AMP Mute ON" : Built-in Amp Mute is ON.
"Builtin AMP Mute OFF" : Built-in Amp Mute is OFF. (Default
setting)
Display and setting:
"Dimmer ON" : The dimmer setting is on. (Default setting)
"Dimmer OFF" : The dimmer setting is off.
Dual Zone System <In AUX mode>
Time setting for removing the faceplate
You can set the interval during which the open control panel
cannot reverse to be hidden. During the period you have set,
the faceplate can be removed from the faceplate bracket.
The following operation allows separate sound sources to
control the output of the front and rear speakers. The Dual
zone system can only be switched on or off when the source is
set to the AUX mode.
Display and setting:
Display and setting:
"Off Wait" : 0sec / 3sec (Default setting) / 5sec / 10sec / 15sec
/ 20sec / 25sec (sec=seconds)
"Zone 2 ON" : The dual zone system function is on.
"Zone 2 OFF" : The dual zone system function is off. (Default
setting)
NOTE
• You must purchase the optional KCA-S210A/CA-C1AX/KDC-
CPS82/KDC-CX82/KDC-CPS85/KDC-CX85/KDC-CPS87/KDC-
CX87 device before you can use this function.
• You can choose to send the AUX input through the rear
channel, and the unit’s tuner or audio source through the front
channel.
Function of the KDC-X917/KDC-X817/KDC-X717
System Q
When this system is set to on, the System Q factors (Bass
center frequency, Bass quality factor, Bass extend, Middle
center frequency, Middle quality factor, and Treble center
frequency) appear during the audio control mode.
• The Bass, Middle, Treble and Loudness adjustments do not
affect the rear channel.
• When the Dual zone system is turned on, the External disc
control features cannot be used.
• When you set the Dual zone system to on while the non-fading
preout is switched on, the sound of the non-fading preout does
not be outputted.
Display and setting:
"System Q ON" : The System Q factors appear and can be
adjusted. (Default setting)
"System Q OFF" : The System Q factors are not appeared.
— 38 —
Function of the KDC-X917/KDC-X817/KDC-X717
NOTE
External Amp Control
Adjust the bass boost level of the external amplifier using the
main unit.
• When you are listening to the audio source, you cannot change
to another TI station.
• When you turn on the TI function, the motorized antenna will
extend automatically.
Display and setting:
"AMP Bass Flat"/"AMP Bass FLT" :
Bass boost level is flat. (Default setting)
"AMP Bass +6" : Bass boost level is low (+6dB).
"AMP Bass +12" : Bass boost level is high (+12dB).
Clean Reception System Circuit (CRSC)
<In FM reception of Tuner mode>
Temporarily have reception switched from stereo to mono to
reduce multi-path noise when listening to the FM station.
NOTE
As of December 2000, the power amplifiers controllable by the
main unit are as follows:
KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T
Display and setting:
"CRSC ON" : The CRSC is on. (Default setting)
"CRSC OFF" : The CRSC is off.
Function of the KDC-X917/KDC-X817
NOTE
Traffic Information Function
You can listen to traffic information. If you are listening to
tapes or discs, they will continue playing until a traffic bulletin
is broadcast.
Strong electrical fields (such as from power lines) may cause
unstable sound quality when CRSC is turned on. In such a
situation, turn it off.
Display and setting:
"TI ON" : The Traffic Information function is on.
When the function is on, the TI indicator is turned on.
When none is being received, the TI indicator will
blink on and off. When a traffic information station is
being received, the TI indicator will turn on.
When a traffic bulletin begins to be broadcast, "Traffic
Info" will be displayed.
Text Scroll
This function permits the CD text, MD title, Radio text, and
Calender function to be scrolled and the entire text to be
displayed. Switching between manual scrolling and automatic
scrolling is permitted.
If you are listening to a tape or disc when a traffic
bulletin begins, they will automatically be turned off.
When the bulletin ends or poor reception is
experienced, the tape or disc will begin playing again.
"TI OFF" : The Traffic Information function is off. (Default
setting)
Display and setting:
"Scroll Auto" : Automatic scrolling (Default setting)
"Scroll Manual" : Manual scrolling
Switching to a Different Traffic Information Station:
Use the 4 / ¢ buttons to make an auto seek of the TI
stations in a certain band.
— 39 —
Basic Operations of remote
KDC-X917/X817/X717
2CAUTION
Do not set the remote on hot places such as above the
dashboard.
Loading and Replacing the Batteries:
Use two "AAA"-size batteries.
4
¢
Slide the cover while pressing downwards to remove it as
illustrated.
38
Insert the batteries with the + and – poles aligned properly,
following the illustration inside the case.
1
4
7
2
5
8
0
3
6
9
2WARNING
KDC-9017
Store unused batteries out of the reach of children. Contact a
doctor immediately if the battery is accidentally swallowed.
NOTE
+
SRC
SRC
TUNE /4/TRACK
TUNE +/¢/TRACK +
38
• The provided batteries are intended for use in operation
checking, and their service life may be short.
• When the remote controllable distance becomes short, replace
both of the batteries with new ones.
• A portion of the operations may not be possible, depending on
the unit that is connected.
4
FM/DISC +
ATT
AM/DISC
¢
TUNE
TRACK
FM
+
DSIC
38
AM
—
DNPP/
SBF
OK
DNPP
OK
Basic operations
REMOTE CONTROL UNIT
• VOLUME buttons
Press the + button to turn the volume up.
Press the – button to turn the volume down.
— 40 —
• SRC button
Tuner features
Each time you press the SRC button, the mode switches as
follows:
• 4/¢ (TUNE) buttons
Press the 4 button to make decreasing seeks (using the
preset tuning mode).
M
Tuner mode
Press the ¢ button to make increasing seeks (using the preset
tuning mode).
M
CD mode
M
Use to move the cursor left or right during station name input.
External disc control mode 1
• AM/FM buttons
M
Press the AM button to select the AM band.
Press the FM button to select and switch between FM1, FM2,
and FM3 bands.
External disc control mode 2 / AUX mode
M
Standby mode
During station name input, selects digits and symbols.
NOTE
• DIRECT/OK button
During station name input, stores the already input data in
memory and ends the input mode.
During Station name preset play mode, selects station.
Enters and cancels the Direct access tuning mode. (KDC-
X917/X817/X717 only)
• The mode switches to the next mode from any mode which
cannot be used.
• The external disc control mode will differ depending on the unit
that is connected.
• To enable the selection of External disc control mode 2/AUX
mode, you should connect optional switching adapter KCA-
S210A (which allows you to select both External disc control
mode 2 and AUX mode) or CD changer (KDC-CPS87, KDC-
CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) or
switching adapter CA-C1AX (which allows you to select AUX
mode only).
• DNPP button
Enters and cancels the Station Name Preset Play mode.
• 38 button
Enters and cancels the Program Type Selection (PTY) mode.
(KDC-X917/X817 only)
Selects the type of characters at the time of entering the station
name.
During the AUX mode, "AUX" (or AUX-name display) will show
in the display.
When the CA-C1AX is being used, the AUX Mode will replace
the External Disc Control Mode.
• Number/letter entry buttons (KDC-X917/X817/X717 only)
Press buttons #1-6 to recall preset stations.
Use to enter letters (alphabetical) during station name preset.
Use to enter frequency of the desired station during Direct
access tuning mode.
• ATT button
Turns down the volume quickly. To return the volume to its
original level, press the button again. Turning the volume up, or
turning it all the way down deactivates the attenuator function.
— 41 —
Basic Operations of remote
CD/External disc control features
• 4/¢ buttons
Press the 4 button to search through the tracks backward.
Press the ¢ button to search through the tracks forward.
Use to move the cursor while entering disc name.
• DISC buttons (for disc changers)
Press the DISC– button to search through the discs backward.
Press the DISC+ button to search through the discs forward.
Select numbers and symbols while entering disc name.
• 38 button
When a disc is playing, this button pauses the play.
Press the same button again to start play again.
Selects the type of characters at the time of entering the disc
name.
• OK button
During disc name input, stores the already input data in memory
and ends the input mode.
Selects disc during the disc name preset play mode.
• DNPP button (for disc changers)
Enters and cancels the Disc Name Preset Play mode.
• Number/letter entry buttons (KDC-X917/X817/X717 only)
Used to specify the track (disc) number used in direct track
(disc) searches.
Use to enter letters during disc name preset.
— 42 —
Accessories
Installation Procedure
1. To prevent a short circuit, remove the key from the ignition and
External view
External view
......... Number of items
disconnect the - battery.
......... Number of items
2. Make the proper input and output wire connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following order: ground,
battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
1
2
3
7
.........1
.........1
8
9
0
.........1
.........2
.........1
8. Press the left part at the upper side of the faceplate once to
make the faceplate control panel appear.
.........1
.........1
2CAUTION
• If your car's ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition wire
to a power source with a constant voltage supply, as with
battery wires, the battery may die.
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Do not let unconnected wires or terminals touch metal on
the car or anything else conducting electricity. To prevent a
short circuit, do not remove the caps on the ends of the
unconnected wires or the terminals.
4
5
6
.........1
.........2
.........2
2CAUTION
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
Do not use any accessories other than those provided with
your unit. If you use other accessories, you may damage the
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Insulate unconnected wires with vinyl tape or other similar
material.
• Some disc changers need conversion cords for connection.
See the section on "Safety Precautions" for details.
• Mount the unit so that the mounting angle is 30° or less.
— 43 —
Connecting Wires to Terminals
2WARNING
Rear right output (Red)
Rear left output (White)
If you connect the ignition wire (red) and the battery
wire (yellow) to the car chassis (ground), you may
cause a short circuit, that in turn may start a fire.
Always connect those wires to the power source
running through the fuse box.
Non-fading right output (Red)
(KDC-X917/X817/X717 only)
Non-fading left output (White)
(KDC-X917/X817/X717 only)
2CAUTION
When only two speakers are being connected to the
system, connect the connectors either to both the
front output terminals or to both the rear output
terminals (do not mix front and rear). For example, if
you connect the + connector of the left speaker to a
front output terminal, do not connect the - connector
to a rear output terminal.
Front right output (Red)
Front left output (White)
To KENWOOD disc changer/
DAB control input/
KPA-SD100/KPA-HD100/KPA-
SS100
NOTE
To connect these leads, refer to the
relevant instruction manuals.
FM/AM antenna input
If no connections are made, do not let the wire come out from the tab.
Fuse (10A)
Wiring harness
(Accessory1)
When using the optional power amplifier, connect
P.CONT
to its power control terminal.
Power control wire (Blue/White)
Depending on what antenna you are using, connect
either to the control terminal of the motor antenna, or
to the power terminal for the booster amplifier of the
film-type antenna.
White/Black
ANT
CONT
Motor antenna control wire (Blue)
To front left
speaker
FRONT • L
+
White
To car light control switch
ILLUMI
Dimmer control wire (Orange / White)
Gray/Black
To front right
speaker
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.
EXT.
CONT.
FRONT • R
+
External amplifier control wire
(Pink / Black) (KDC-X917/X817/X717 only)
Gray
Green/Black
Ignition key
switch
To rear left
speaker
REAR • L
+
ACC
Green
Ignition wire (Red)
Car fuse box
Car fuse
box
(Main fuse)
Purple/Black
Battery wire (Yellow)
To rear right
speaker
REAR • R
+
Purple
Ground wire (Black) - (To car chassis)
Battery
–
+
— 44 —
Installation (non-Japanese cars)
Locking the faceplate to the unit
I
Installation (non-Japanese cars)
I
Locking the faceplate to the unit
If you want to lock the faceplate to the unit so that it does not
fall off, follow the directions below.
Firewall or metal support
1
2
Refer to the function "Removing the faceplate (page 14)" and
remove the faceplate.
Accessory4
Insert the provided screw into the hole at the center of the
bottom side of the faceplate which you have removed from
the unit.
Bend the tabs of the
mounting sleeve with
a screwdriver or similar
utensil and attach it in
place.
Accessory7
Phillips truss
head sheet
metal screw
(commercially
available)
3
Refer to the section "Removing the faceplate (page 14)" and
then reattaching the faceplate.
2CAUTION
Accessory2
Metal mounting
strap
Never insert the taptite screws (ø2 × 4 mm) in any other
screw holes than the one specified. If you insert it in another
hole, it will contract and may cause damage to the mechanical
parts inside the unit.
NOTE
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
2CAUTION
To attach this unit, make sure the front of the control panel faces
you and fit it into the mounting sleeve by pressing the four
corners of the hard rubber frame at the same time.
Do not apply strong pressure to other sections than the corners;
otherwise troubles such as the impossibility of opening or closing
the panel may result.
— 45 —
Removing the Unit
I
I
Removing the Unit
Removing the hard rubber frame
Insert the removal tool into the indentations in the hard rubber
frame, and pull it gently until the lock is released.
1
Refer to the section “Removing the hard rubber frame” and
then remove the hard rubber frame.
2
3
Remove the Hex-head screw with integral washer (M4×8) on
the back panel.
Insert the two removal tools deeply into the slots on each
side, as shown.
Accessory4
Catch facing up
Accessory0
Removal tool
Accessory3
Removal tool
4
Push upward the removal
tool toward the top, and
pull out the unit halfway
whilst pressing towards the
inside.
2CAUTION
Be careful to avoid injury from the catch pins on the removal
tool.
5
Pull the unit all the way out
with your hands, being
careful not to drop it.
— 46 —
Installation (Japanese-cars)
I
Installing Radio Bracket in Japanese-made Cars (J-Cars)
(For Nissan Car)
After aligning the J-Car bracket with
the factory-installed radio bracket,
tighten the screws.
8mm
Accessory8
J-Car Bracket
Accessory5
for Nissan car
5mm
(follow indications for L/R)
Factory-installed
Radio Bracket
(For Toyota Car)
After aligning the factory-installed
radio bracket, tighten the screws.
8mm
Accessory6
for Toyota car
Factory-installed
Radio Bracket
L
5mm
NOTE
A pair of J-Car Brackets (Accessory 8)
are not used when fitting in a Toyota
car.
R
2CAUTION
Damage to the unit will result from
using screws other than those
provided.
Factory trim bezel
Accessory9
J-Car Trim Plate
(place thick part on
bottom)
— 47 —
Troubleshooting Guide
What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The power does not turn on.
The fuse has blown.
After checking for short circuits in the wires, replace the
fuse with one with the same rating.
Nothing happens when the
buttons are pressed.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (see p. 5).
Radio reception is poor.
The car antenna is not extended.
Pull the antenna out all the way.
The antenna control wire is not connected.
Connect the wire correctly, referring to the section on
"Connecting Wires to Terminals".
The memory is erased when
the ignition is turned off.
The battery wire has not been connected to the proper
terminal.
Connect the wire correctly, referring to the section on
"Connecting Wires to Terminals".
The ignition and battery wire are incorrectly connected.
Connect the wire correctly, referring to the section on
"Connecting Wires to Terminals".
The faceplate does not open or
close.
The faceplate is incorrectly attached.
Reattach the faceplate correctly, See the section on
"Removing the Faceplate".(page.14)
Free switching of the sound
quality.
The system Q function is set on Scan mode.
Refer to the “System Q” page and switch it to a
function other than Scan mode.(see p. 10)
Audio control setting cannot be
achieved.
The system Q function is set on Scan mode.
Refer to the “System Q” page and switch it to a
function other than Scan mode.(see p. 10).
— 48 —
PROBLEM
POSSIBLE CAUSE
SOLUTION
No sound can be heard, or the
volume is low.
Attenuator is turned on.
Turn off Attenuator.
The fader or balance settings are set all the way to one
side.
Reset the fader or balance settings.
The input/output wires or wiring harness are connected
incorrectly.
Reconnect the input/output wires or the wiring harness
correctly. See the section on "Connecting Wires to
Terminals".
The values of Volume offset are low.
Increase the values of Volume offset. (see p. 18)
Check the speaker wiring.
One of the speaker wires is being pinched by a screw in
the car.
The sound quality is poor or
distorted.
The speakers are not wired correctly.
Reconnect the speaker wires so that each output
terminal is connected to a different speaker.
A CD ejects as soon as it is
loaded.
The CD is upside-down.
The CD is quite dirty.
Load the CD with the labeled side up.
Clean the CD, referring to the section on "Cleaning CDs"
(see p. 6).
The sound skips on a CD.
The CD is scratched or dirty.
Clean the CD, referring to the section on "Cleaning CDs"
(see p. 6).
A track will not play.
Random play has been selected.
Turn off random play.
Can’t remove disc.
The cause is that more than 10 minutes has elapsed
since the vehicle ACC switch was turned OFF.
The disc can only be removed within 10 minutes of the
ACC switch being turned OFF. If more than 10 minutes
has elapsed, turn the ACC switch ON again and press
the Eject button.
— 49 —
Troubleshooting Guide
CD/External disc control mode
PROBLEM
POSSIBLE CAUSE
SOLUTION
The disc control mode cannot
be selected.
No wire has been connected to the disc changer input
terminal on the unit.
Connect the wire to the disc changer input terminal on
the unit.
The specified disc does not
play, but another one plays
instead.
The specified CD is quite dirty.
Clean the CD.
The CD is upside-down.
Load the CD with the labeled side up.
The disc is loaded in a different slot from that specified.
Eject the disc magazine and check the number for the
specified disc.
The disc is severely scratched.
Something is touching the disc changer.
The CD is scratched or dirty.
Try another disc instead.
The sound skips.
Remove whatever is touching it.
If skipping happens at the same place when the car is
stopped, something with the CD is wrong. Clean the CD.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (see p. 4).
The display shows that the
changer is being played, but no
sound can be heard.
The specified track will not
play.
Random play or magazine random play has been
selected.
Turn off random play or magazine random play.
Track repeat, disc repeat, track
scan, random play, and
magazine random play start by
themselves.
The setting is not canceled.
The settings for these functions remain on until the
setting to off or the disc ejected, even if the power is
turned off or the source changed.
Cannot play CD-R or CD-RW.
Finalization processing is not being conducted for CD-
R/CD-RW.
Conduct finalization processing with CD recorder.
A non-compatible CD changer is being used to play the
CD-R/CD-RW.
Use a CD changer compatible with CD-R/CD-RW to play.
If the following situations, consult your nearest service center:
• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX-85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is
entered when switching modes.
— 50 —
The following messages are displayed when certain problems are occurring in your system. Take the
recommended actions.
No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.
Eject
] Load the disc magazine properly.
No CD in the unit.
] Insert the CD.
No disc has been loaded in the disc magazine.
] Load a disc into the disc magazine.
No Disc
No disc has been loaded in the disc magazine.
] Load a disc into the disc magazine.
TOC Error
The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.
] Clean the CD and load it correctly.
Nothing has been recorded on the MD.
Blank DISC
No Tr DISC
NO PANEL
No tracks are recorded on the MD, although it has a title.
The faceplate of the slave unit being connected to this unit has been removed.
] Replace it.
The unit is malfunctioning for some reason.
] Press the reset button on the unit. If the "E- 77" code does not disappear, consult your nearest service center.
E-77
Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.
] Check the disc magazine. And then press the reset button on the unit. If the "Mecha Error" code does not disappear,
consult your nearest service center.
Mecha Error
The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),
stopping all operation.
] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),
the disc will start playing again.
Hold Error
IN
If this indicator blinks, the CD player is malfunctioning.
] Eject the CD and try inseting it again.
If the CD cannot be ejected, press the eject button and hold it in until the CD is ejected.
— 51 —
Specifications
Specifications subject to change without notice.
FM tuner section
Audio section
Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz
Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 Ω)
Quieting Sensitivity (S/N = 50dB) ...............15.2dBf (1.6 µV/75 Ω)
Frequency response ( 3.0 dB)..............................30 Hz – 15 kHz
Signal to Noise ratio (MONO)..............................................70 dB
Selectivity ( 400 kHz).......................................................≥ 80 dB
Stereo separation (1 kHz) ....................................................40 dB
Maximum output power.................................................50 W × 4
Full Bandwidth Power (at less than 1% THD) ................22 W × 4
Tone action
Bass : ..........................................................100 Hz 10 dB
Middle : .........................................................1 kHz 10 dB
Treble : ........................................................10 kHz 10 dB
Preout level / Load (during disc play)....................4500 mV/10 kΩ
Preout impedance.................................................................80 Ω
AM tuner section
Frequency range (10 kHz space) ...................530 kHz – 1700 kHz
Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)
General
Operating voltage (11 – 16V allowable) ..............................14.4 V
Current consumption.............................................................10 A
Installation Size (W x H x D) ..........................182 × 53 × 162 mm
7-3/16 × 2-1/16 × 6-3/8 in.
CD player section
Laser diode ....................................................GaAlAs (λ=780 nm)
Digital filter (D/A) .....................................8 Times Over Sampling
D/A Converter .......................................................................1 Bit
Spindle speed ..............................................500 – 200 rpm (CLV)
Wow & Flutter........................................Below Measurable Limit
Frequency response ( 1 dB).................................10 Hz – 20 kHz
Total harmonic distortion (1 kHz) ......................................0.01 %
Signal to Noise ratio (1 kHz) ..............................................105 dB
Dynamic range ....................................................................93 dB
Channel separation..............................................................96 dB
Weight ..................................................................4.2 lbs (1.9 kg)
— 52 —
|