Wireless G
UsB AdApter
User mAnUAl
Model 530361
INT-530361-UM-0408-01
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™
Wireless G USB Adapter, Model 530361.
Compatible with 802.11b and 802.11g wireless access points and routers,
this adapter lets you upgrade your wireless network without the need to
replace existing equipment. Transfer or receive digital images, videos
and MP3 files with link speeds of up to 54 Mbps using proven and reliable
Wireless G technology. With the easy-to-follow instructions in this manual,
you’ll soon be able to enjoy the benefits of these additional features:
• Connects your notebook or PC to a wireless network
• Includes USB stand and extension cable
• Turbo Mode technology for enhanced wireless throughput
• Supports WEP (64/128 bit), WPA and WPA2 data encryption
• Supports Software AP function (turns your wireless client into a
wireless access point)
• Supports WMM (Wi-Fi Multimedia) for increased multimedia data
throughput
• Windows 98SE/2000/Me/XP/Vista compatible
• Lifetime Warranty
FCC CertiFiCations
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
ꢀ
CAUTION: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference; and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC rF radiation exposure statement
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment, and should be installed and operated with
a minimum distance of 2.5 cm (1 in.) between the radiator and your body.
SAR (specific absorption rate) compliance has been established in laptop
computer configurations with a USB port on the side near the center, as
tested in the application for certification, and can be used in laptops with
substantially similar physical dimensions, construction and electrical and
RF characteristics. Use in other devices, such as PDAs or lap pads, is
not authorized. This transmitter is restricted for use with the specific
antenna(s) tested in the application for certification. The antenna(s) used
for this transmitter must not be co-located or operated in conjunction with
any other antenna or transmitter.
r&tte ComplianCe statement
This equipment complies with all the requirements of Directive 1999/5/EC
of the European Parliament and the Council of March 9, 1999, on radio
equipment and telecommunication terminal equipment (R&TTE) and the
mutual recognition of their conformity. The R&TTE directive repeals and
replaces Directive 98/13/EEC (Telecommunications Terminal Equipment
and Satellite Earth Station Equipment) as of April 8, 2000.
eu Countries intended For use
The ETSI version of this device is intended for home/office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden and the U.K., and
is also authorized for use in EFTA member states Iceland, Liechtenstein,
Norway and Switzerland. (EU countries not intended for use: none.)
ꢁ
tABle of contents
section
page
Installation..........................................................................................6
Configuration ....................................................................................7
Network........................................................................................9
Profile ................................................................................................10
Profile Configuration ............................................................. 12
Profile Authentication & Encryption (Security)...................... 13
802.1x Setting/Certification................................................... 16
802.1x Setting/CA Server...................................................... 17
Statistics .................................................................................... 18
Advanced................................................................................... 18
WMM..........................................................................................21
About..........................................................................................22
WPS Configuration....................................................................22
SoftAP ......................................................................................................24
Configuration .............................................................................24
Security Setting .........................................................................26
Access Control ..........................................................................28
MAC Table .................................................................................29
Event Log...................................................................................29
Statistics ....................................................................................30
About..........................................................................................30
Specifications................................................................................... 31
NOTE: Some screen-shot images have been modified to fit the format
of this user manual.
ꢂ
CONTENTS
instAllAtion
Prior to connecting the Wireless G USB Adapter:
• Uninstall any previously loaded versions of the driver and utility.
• Install the software program from the CD. NOTE: The following Windows
XP procedure is similar for Windows 98SE/Me/2000/2003/Vista.
1. Insert the setup CD in the CD-ROM drive and run the setup program.
2. Read the license agreement that displays; click “Yes” to proceed.
3. In Windows XP, a “Microsoft (Windows) Zero Configuration Tool” option
displays. It’s recommended that the alternative “Ralink Configuration
Tool” option be selected, as it features more functions. Click “Next.”
4. To run the adapter at a higher speed, select “Optimize for performance”
to enable the Tx Burst mode. Otherwise, “Optimize for WiFi” sets the
adapter to run with a standard wireless network. Click “Next.”
ꢃ
INSTALLATION
5. Once the software
installation begins,
a Setup Status
screen is followed
by a prompt to
connect the Wireless
G USB Adapter to
your computer. The
system automatically
detects the adapter.
NOTE: In Windows
Vista, a Found New
Hardware screen appears (above) when the adapter is connected. You
can ignore the message, as it disappears once installation is complete.
6. When the Finish screen appears, click “Finish.”
confiGUrAtion
The configuration utility — which displays automatically once the adapter
is connected — is a powerful application that helps you configure the
adapter and monitor link status and statistics during the communication
process. This adapter will auto-connect to the wireless device that has
the better signal strength and no wireless security setting.
ꢄ
CONFIGURATION
The configuration utility appears as an icon in the Windows system tray
while the adapter is running. You can
open it by double-clicking on the icon.
In Windows XP, there is a “Windows Zero Configuration Tool” option for
setting up wireless clients. If you prefer to use the configuration utility,
there are two ways to switch to it instead of using the Windows tool.
option 1
1. Right-click the utility icon in the
system tray and select “Use
RaConfig as Configuration
utility.”
option 2
1. Right-click the icon on the left side
of the system tray and select “View Available Wireless Networks.”
2. Click “Change advanced settings.”
ꢅ
CONFIGURATION
3. Uncheck “Use Windows
to configure my wireless
network settings” to
enable the utility for the
adapter. NOTE: If
“Wireless Zero
Configuration Tool” is
enabled, you can only
configure the advanced
settings or check the
link status and statistics
from the configuration
utility of the adapter.
NETWORK
When you open the configuration utility, the system scans all the channels
to find access points/stations within the accessible range of the adapter
and automatically connect to the wireless device with the highest signal
strength. On the Network screen, all the networks nearby are listed.
You can change the connection to another network or add one of the
networks to your own profile list.
ꢆ
CONFIGURATION
Available Networks: This list shows all available wireless networks within
the range of the adapter. It also displays network information: SSID,
BSSID, Signal Strength, Channel, Encryption, Authentication and
Network Type. To connect to a network on the list, double-click the
item and the adapter will connect automatically to it.
Rescan: Click “Rescan” to collect the new information of all the wireless
networks nearby.
Connect: Click “Connect” to connect to the selected network.
Add to Profile: Click to add the selected network to the Profile list.
PROfIlE
The Profile screen is for managing networks you connect to frequently.
You can add, delete, edit and activate a profile on this screen.
Profile List: The Profile List displays all the profiles and their related
settings, including Profile Name, SSID, Channel, Authentication,
Encryption and Network Type.
Add, Edit, Delete: Click the corresponding button to add, edit or delete
the selected profile(s). Clicking “Add” displays the Add Profile screen,
which presents 1) Configuration and 2) Authentication and Encryption
(Security).
Activate: To display status information about your current wireless
connection, select the profile and click “Activate.” When a profile is
activated, the adapter will be initially connected to it.
10
CONFIGURATION
Status: This field displays the SSID and MAC ID of the network the
adapter is connecting to.
Extra Info: This field displays the link status.
Channel: This field displays the number of the radio channel and the
frequency used for the networking.
Link Speed (Mbps): These fields display the transmission (Tx) and the
reception (Rx) rates of the network. The maximum transmission rate
is 54 Mbps.
Throughput (Kbps): These fields display the speed of data being
transmitted (Tx) and received (Rx).
Link Quality: This status bar indicates the quality of the link. The
higher the percentage, the better the quality.
dBm: To display the signal strength measured in dBm (decibels in
milliwatts), click this box on the Network screen (see Page 9).
Signal Strength: This bar shows the signal strength level. The higher
the percentage being shown in the bar, the more radio signal being
received by the adapter. This indicator helps to find the proper position
of the wireless device for quality network operation.
Noise Strength: This bar displays the noise level in the wireless
environment.
11
CONFIGURATION
proFile ConFiguration
Profile Name: Define easily recognizable profile names to identify the
different networks.
SSID: The SSID (up to 32 printable ASCII characters) is the unique name
identified in a WLAN. The ID prevents the unintentional merging of
two co-located WLANs. If you specify an SSID for the adapter, then
only the device with the same SSID can interconnect to the adapter.
To add a nearby network to the profile list, pull down the menu to view
all the networks that can be selected.
Power Save Mode: The two power-saving functions are available only
when Network Type (see below) is set to “Infrastructure.”
• CAM (Constantly Awake Mode): With this selected, the adapter
will remain in an active mode.
• PSM (Power Save Mode): Enable the adapter in the power-save
mode when it is idle.
Network Type: Select from the drop-down menu.
• Infrastructure: This operation mode requires the presence of an
802.11 access point. All communication is done via the AP or router.
• Ad-Hoc: Select this mode to connect to another wireless station in
the wireless LAN network without using an access point or router.
Tx Power: To lower the transmit power of the adapter to reduce the power
used by the system, select a lower percentage from the drop-down
menu. NOTE: A lower power level will result in lower signal strength
and reduced coverage range.
12
CONFIGURATION
RTS Threshold: This is the minimum packet size required for an RTS
(request to send). For packets smaller than this threshold, an RTS is
not sent and the packet is transmitted directly to the wireless network.
Select a setting within a range of 0 to 2347 bytes. NOTE: A minor
change is recommended.
Fragment Threshold: This value defines the maximum size of packets;
any packet size larger than the value will be fragmented. If you’ve
decreased this value and experience high packet-error rates, you
can increase it again, but it will likely decrease overall network
performance. Select a setting within a range of 256 to 2346 bytes.
NOTE: A minor change is recommended.
proFile authentiCation and enCryption (seCurity)
Authentication Type: This pull-down menu setting has to be consistent
with the wireless networks that the adapter is intended to connect.
• Open: No authentication is needed within the wireless network.
• Shared: Only wireless devices using a shared key (WEP key
identified) are allowed to connect to each other.
• LEAP: This is a pre-EAP, Cisco-proprietary protocol with many of
the features of EAP protocols. Cisco controls the ability of other
vendors to implement this protocol, so it should be selected for use
only when a limited vendor choice for client, access point and server
products is not a concern. When you’ve set up LEAP authentication,
you need to enter the username and password of your computer.
• WPA: WPA provides a scheme of mutual authentication using either
IEEE 802.1x/Extensible Authentication Protocol (EAP) authentication
1ꢀ
CONFIGURATION
or pre-shared key (PSK) technology. It provides a high level of
assurance to enterprises, small businesses and home users that
data will remain protected and that only authorized users may access
their networks. For enterprises that have already deployed IEEE
802.1x authentication, WPA offers the advantage of leveraging
existing authentication databases and infrastructure.
• WPA-PSK: This is a special mode designed for home and small
business users who do not have access to network authentication
servers. In this mode, known as Pre-Shared Key, you manually
enter the starting password in your access point or gateway, as
well as in each wireless station in the network. WPA-PSK takes
over automatically from that point, keeping unauthorized users who
don’t have the matching password from joining the network, while
encrypting the data traveling between authorized devices.
• WPA2: Like WPA, WPA2 supports IEEE 802.1x/EAP authentication,
or PSK, technology. It also includes a new advanced encryption
mechanism using the Advanced Encryption Standard (AES). AES is
required for corporate or government users. The difference between
WPA and WPA2 is that WPA2 provides data encryption via AES. In
contrast, WPA uses the Temporal Key Integrity Protocol (TKIP).
• WPA2-PSK: This is also for home and small business use. The
difference between WPA-PSK and WPA2-PSK is that WPA2-PSK
provides data encryption via the AES. In contrast, WPA-PSK uses
the Temporal Key Integrity Protocol (TKIP).
• WPA-NONE: This is defined for Ad Hoc mode and behaves like
WPA-PSK (WPA-PSK is only defined for Infrastructure mode). The
user manually enters the Pre-Shared Key in each wireless station
in the network, and WPA-NONE controls unauthorized users who
don’t have the matching Pre-Shared Key from joining the network.
It also encrypts the data traveling between authorized devices.
802.1x Setting: When Authentication Type is set to “Open,” “Shared,”
“WPA” or “WPA2,” you can also enable IEEE 802.1x Setting to use the
authentication server or certification server to authenticate client users.
NOTE: See the two separate 802.1x Setting sections below for details.
Encryption: Select from the drop-down menu.
• None: Disables the encryption mode.
1ꢁ
CONFIGURATION
• WEP: Enables the WEP Data Encryption. When the item is selected,
you need to continue setting the WEP Encryption keys.
• TKIP: The Temporal Key Integrity Protocol changes the temporal key
every 10,000 packets (a kind of message transmitted over a network.)
This ensures much greater security than the standard WEP security.
• AES: AES has been developed to ensure the highest degree of
security and authenticity for digital information. It’s the most advanced
solution defined by IEEE 802.11i for security in the wireless network.
NOTE: All devices in the network should use the same encryption
method to ensure the security of communications.
WPA Pre-Shared Key: The WPA-PSK key can be 8 to 64 characters in
length and can be letters or numbers. This same key must be used on
all the wireless stations in the network.
WEP Key (Key#1–4): WEP keys are used to encrypt data transmitted
in the wireless network. There are two types of key length: 64-bit and
128-bit. Assign a default encryption key (Key#1 to Key#4) by clicking
on the corresponding radio button. To fill in each text field:
• 64-bit: Input 10-digit hex values (in the A-F, a-f and 0-9 range) or
5-digit ASCII characters (a-z and 0-9) as the encryption keys.
For example: “0123456aef“ or “test1.”
• 128-bit: Input 26-digit hex values (in the A-F, a-f and 0-9 range) or
13-digit ASCII characters (“a-z” and “0-9”) as the encryption keys.
For example: “01234567890123456789abcdef“ or “administrator.”
The IEEE 802.1X specification describes a protocol that can be used for
authenticating both clients (802.1x Setting/Certification below) and servers
(802.1x Setting/CA Server below) on a network. The authentication
algorithms and methods are those provided by the Extensible Authentication
Protocol (EAP), a method of authentication that has been in use for a
number of years on networks that provide Point-to-Point Protocol (PPP)
support (as many Internet service providers and enterprises do). EAP
runs before network layer protocols transmit data over the link.
When an AP acting as an authenticator detects a wireless station on the
LAN, it sends an EAP request for the user’s identity to the device. In
turn, the device responds with its identity, and the AP relays this identity
to an authentication server (typically an external RADIUS server).
1ꢂ
CONFIGURATION
IEEE ꢅ02.1x Access Client
RADIUS Client
RADIUS Server
1
ꢀ
Access Point
2
ꢁ
Windows 200
1 Client requests to log in to the network
2 Log in with username and password
ꢀ Username and password sent to RADIUS server
ꢁ User login to the LAN approved or denied
802.1x setting/CertiFiCation
EAP Method: The EAP authentication protocols supported by this
adapter require that settings be consistent with the wireless access
points or routers that the adapter is intended to connect.
• PEAP & TTLS: These protocols are similar and easier to use than
TLS (below) in that they specify a stand-alone authentication protocol
to be used within an encrypted tunnel. TTLS supports any protocol
within its tunnel, including CHAP, MS-CHAP, MS-CHAPv2, PAP and
EAP-MD5. PEAP specifies that an EAP-compliant authentication
protocol be used; this adapter supports EAP-MSCHAP v2, EAP-TLS/
Smart Card and Generic Token Card. The client certificate is optional.
• TLS/Smart Card: This is the most secure of the EAP protocols, but
isn’t easy to use: It requires that digital certificates be exchanged in
1ꢃ
CONFIGURATION
the authentication phase. The server presents a certificate to the
client and, after validating the server’s certificate, the client presents
a client certificate to the server for validation.
Session Resumption: Click/check the box to activate or de-activate.
ID/Password: Enter the password as the identity for the server.
Client Certification: A client certificate is required for TLS, but is
optional for TTLS and PEAP. This forces a client certificate to be
selected from the appropriate Windows Certificate Store and made
available to the RADIUS server for certification.
Tunneled Authentication/Protocol: When the authentication type is
PEAP or TTLS, select a protocol for building the encrypted tunnel.
Tunnel Authentication: Select one of three options from the drop-
down menu: “EAP-MSCHAPv2,” “EAP-TLS/Smart card” or “Generic
Token Card.”
802.1x setting/Ca server
Use certificate chain: When the Extensible Authentication Protocol
(EAP) authentication type — such as TLS, TTLS or PEAP — is
selected and requires certification to tell the client what credentials to
accept from the authentication server in order to verify the server, you
need to enable this function. Choose the preferred server from the
drop-down menu to issue the certificate. If “Any Trusted CA” is
selected, any CA (certification authority) on the list (which is provided
by the Microsoft Certificate Store) is permitted.
Allow intermediate certificates: A server designates an issuer as a
trusted root authority by placing the issuer’s self-signed certificate,
1ꢄ
CONFIGURATION
which contains the issuer’s public key, into the trusted root certification
authority certificate store of the host computer. Intermediate or
subordinate certification authorities are trusted only if they have a
valid certification path from a trusted root certification authority.
Server Name: Enter the authentication server name.
Server name must match exactly: When selected, the server name
must exactly match the server name found on the certificate.
Domain name must end in specified name: When this is selected,
the server name field identifies a domain. The certificate must use a
server name belonging to this domain or one of its sub-domains (e.g.,
zeelans.com, where the server is blueberry.zeelans.com), but it may
be any name used in the certificate name field.
STATISTIcS
This screen enables you to view/compare the transmit and receive
statistical information of the connection. To reset the counters, click
”Reset Counter.”
ADvANCED
This screen enables you to configure more advanced settings, such as
the wireless mode and the protection mode.
Wireless Mode: Select from the drop-down menu.
• 802.11 B/G mix: If you have a mix of 802.11b and 802.11g wireless
stations in your network, it is recommended that the adapter be set
1ꢅ
CONFIGURATION
to this mode. This mode is also the default setting.
• 802.11 B only: Though the adapter is compatible with both 802.11g
and 802.11b wireless stations, if there are only 802.11b wireless
stations in the network, you can set the adapter to this mode.
Ad Hoc Wireless Mode: When the adapter is set in Ad Hoc (Peer to
Peer) mode, you can designate the wireless connection mode for the
Ad Hoc network.
• Only B: Though the adapter is compatible with both 802.11g and
802.11b wireless stations, if there are only 802.11b wireless stations
in the network, you can set the adapter to this mode.
• B/G Mixed: If you have a mix of 802.11b and 802.11g wireless
stations in your network, it is recommended that the adapter be set
to this mode. This mode is also the default setting.
• Only G: Though the adapter is compatible with both 802.11g and
802.11b wireless stations, if there are only 802.11g wireless stations
in the network, you can set the adapter to this mode.
Wireless Protection: If you have a mix of 802.11b and 802.11g wireless
stations in the network, it’s recommended that you enable the protection
mechanism, which can decrease the rate of data collisions between
802.11b and 802.11g wireless stations. When the protection mode is
enabled, the throughput of the adapter will be a little lower.
• Auto: Depending on the status of the network, this automatically
disables/enables the protection mode.
• On: Always enables the protection mode.
• Off: Always disables the protection mode.
1ꢆ
CONFIGURATION
Tx Rate: There are several options in the drop-down menu: “Auto” and a
range of speeds from “1 Mbps” to “54 Mbps.” When “Auto” is selected,
the device automatically chooses the most suitable transmission rate.
The higher the data rate designated in the network, the shorter the
distance allowed between the adapter and the wireless stations.
When the wireless mode is “802.11 B Only,” the maximum data rate is
11 Mbps (11b), making only “Auto,” “1 Mbps,” “2 Mbps,” “5.5 Mbps” and
“11 Mbps” available as options.
Enable Tx Burst: This enables the adapter to deliver better throughput
in the same period and environment.
Enable TCP Window Size: The TCP window is the amount of data a
sender can deliver on a particular connection before it gets an
acknowledgment back from the receiver that it has gotten some of it.
When the router or AP the adapter is connecting to has set up the
TCP window, you can enable the parameter to meet the data size for
the router or AP connection. The larger the TCP window, the better
the performance.
Fast Roaming at [-70] dBm: To fast roam to a nearby network without
interrupting the wireless connection (such as a multimedia application
or a voice call), you can set this parameter. The adapter will fast roam
when the receive sensitivity (signal strength) is below the value entered.
Show Authentication Status Dialog: Select to display.
Select Your Country Region Code: Channel availability varies from
country to country; for example, USA (FCC) channels are 1-11, while
Europe (ETSI) channels are 1-13.
Enable CCX: Cisco Compatible Extensions, for radio monitoring and
fast roaming.
Turn on CCKM: During normal operation, LEAP-enabled client devices
mutually authenticate with a new AP by performing a complete LEAP
authentication, including communication with the main RADIUS server.
When a wireless LAN is configured for fast re-association, however,
LEAP-enabled client devices roam from one access point to another
without involving the main server. Using Cisco Centralized Key
Management (CCKM), an access point configured to provide wireless
domain services (WDS) takes the place of the RADIUS server and
20
CONFIGURATION
authenticates the client so quickly that there is no perceptible delay
in voice or other time-sensitive applications.
Enable Radio Measurement: When this parameter is enabled, the Cisco
AP can run the radio monitoring through the associated CCX-compliant
clients to continuously monitor the WLAN radio environment and
discover any new APs that are transmitting beacons.
Non-Serving Channel Measurements: The Cisco access point can
perform monitoring measurements through the CCX-compliant clients
on the non-serving channels when this parameter is enabled.
Limit [xxx] milliseconds (0-2000): This setting limits the channel
measurement time. The default value is 250 milliseconds.
Turn off RF: Click to turn off the radio of the adapter; click again to turn
it back on.
WMM
This screen enables you to configure WMM (Wi-Fi Multimedia) and
other QoS settings, such as Power Save and Direct Link Setup.
WMM Enable: Click the check box (then click “Apply”) to enable the WMM
function, which then lets you configure the WMM Power Save and
Direct Link Setup functions.
• WMM – Power Save Enable: Click the check box to enable, then
click “Setting” to further configure the function as “AC_BK,” “AC_BE,”
“AC_VI” or “AC_VO.”
21
CONFIGURATION
• Direct Link Setup Enable: Click the check box to enable, then click
“Apply” to further configure the function (all within the Direct Link panel).
- MAC Address: Specify the MAC address of the client adapter you
want to direct link to and click “Apply” to add to the DLS Status
table (below).
- Timeout value: Specify the timeout value for the direct link being
set up.
ABOUT
On this screen, you can click the hyperlink for information on the wireless
chipset manufacturer. Basic information about the utility (driver, EEPROM
version, etc.) also displays, as do various addresses for quick reference.
NOTE: This adapter features Turbo Mode, which delivers a higher
throughput than IEEE 802.11g standard (up to 54 Mbps) by compressing
data and decreasing the wait time for sending data to routers or access
points. Turbo Mode is enabled automatically without any configuration.
WPS CONFIGURATION
The adapter supports WPS (Wi-Fi Protected Setup), allowing connection
to wireless APs without complicated procedures. Two WPS configuration
methods are available: PBC (push-button configuration) and PIN.
WPS AP List: Wireless access points offering WPS service are shown
22
CONFIGURATION
in this list. If the list is empty, that means that no WPS-enabled AP is
in the range.
WPS Probe IE: The Wireless Provisioning Services Information Element
(WPS IE) makes it easier to connect to public Wi-Fi networks you’ve
not previously connected to. Your computer must have the WPS IE
update for Windows XP SP2 installed in order to use the function.
Automatically select the AP: Select to activate.
Rescan: Click to scan for WPS-enabled APs (perform a site survey).
Information: Select a found WPS-enabled access point, then click
“Information” to display that AP’s details in a pop-up window.
PIN Code: The WPS PIN Code of this network adapter is required for
connection.
SSID (lower panel): The service set identifier of the connected WPS-
enabled access point.
MAC Address: The MAC address of connected WPS-enabled AP.
Authentication (lower panel): The authentication type of connected
WPS-enabled access point.
Encryption (lower panel): The encryption type of the connected WPS-
enabled access point
Detail: Click to show details of a selected WPS-enabled access point.
Connect: Click to connect to a WPS-enabled access point on the list.
Rotate: Click to connect to next WPS-enabled access point on the list.
Disconnect: Click to disconnect from a connected WPS-enabled access
point. If there are other wireless access points in the profile, the last
2ꢀ
CONFIGURATION
one will be connected; if there’s nothing in the profile, the adapter will
connect to any unsecured wireless AP nearby.
Delete: Delete the WPS-enabled access point from the list.
PIN: To use the PIN-type WPS configuration option, enter the PIN code
and then click “PIN.”
PBC: To use the PBC-type WPS configuration option, put the WPS-
enabled access point in WPS – PBC mode, then click “PBC.”
softAp
This adapter can run as a
wireless access point (AP).
Right-click the configuration
utility icon on the Windows
system tray and select
“Switch to AP Mode” to activate the SoftAP function.
CONFIGURATION
This screen enables you to configure the AP connection setting, the
Country Region Code and other advanced functions.
SSID: The SSID (up
to 32 printable
ASCII characters)
is the unique
MAC
name identified in
a wireless LAN.
The ID prevents
the unintentional
merging of two
co-locatedWLANs.
The default SSID
of the AP is
“SoftAP-X.” (“X”
is the last number
2ꢁ
SoftAp
of this adapter’s MAC address). Wireless adapters connected to the
access point should be set up with the same SSID as the AP.
Tx Rate: There are several options in the drop-down menu: “Auto” and a
range of speeds from “1 Mbps” to “54 Mbps.” When “Auto” is selected,
the device automatically chooses the most suitable transmission rate.
The higher the data rate designated in the network, the shorter the
distance allowed between the adapter and the wireless stations.
When the wireless mode is “802.11 B Only,” the maximum data rate is
11 Mbps (11b), making only “Auto,” “1 Mbps,” “2 Mbps,” “5.5 Mbps” and
“11 Mbps” available as options.
Channel: Select the number of the radio channel used by the access
point. Any wireless adapters connected to the AP should be set up
with the same channel.
Wireless Mode: Selects the wireless mode supported by the AP.
• 802.11 B/G Mixed: The AP works in 11b+g mixed mode.
• 802.11 B Only: The AP works in 11b mode.
• 802.11 G Only: The AP works in 11g mode.
Use MAC Address: Click to create a unique SSID based on the adapter’s
MAC address.
Security Setting: Click to further configure WLAN authentication and
security settings. (See the separate Security Setting section below.)
Country Region Code: Channel availability varies from country to
country; e.g., USA (FCC) channels are 1-11, while Europe’s (ETSI) are 1-13.
Beacon (ms): Define the time between beacons (default is 100 ms.)
Tx Power: To lower the transmit power of the AP to reduce the power
used by the system, select a lower percentage from the drop-down
menu. NOTE: A lower power level will result in lower signal strength
and reduced coverage range.
No forwarding among wireless clients: Enable to prevent wireless
clients connected to this AP from sharing information with each other.
Hide SSID: When this box is checked, the AP will not appear in the site
survey list of any wireless clients, meaning only the wireless clients
set with the same SSID can connect to the AP. This prevents the AP
being connected to by unauthorized users.
Default: Click to use the default value.
Apply: Click to apply the setting change(s).
2ꢂ
SoftAp
SECURITY SETTING
This screen — accessed by clicking “Security Setting” on the previous
SoftAP Configuration screen — lets you to configure the authentication
mode and encryption algorithm used within the AP.
pre-Shared Key
Authentication Type: Four types of authentication mode are
supported and presented in the drop-down menu.
• Open: No authentication is needed within the wireless network.
• WPA-PSK: This is a special mode designed for home and small
business users who do not have access to network authentication
servers. In this mode, known as Pre-Shared Key, you manually
enter the starting password in your access point or gateway, as well
as in each wireless station in the network. WPA-PSK automatically
takes over from that point, keeping unauthorized users who don’t
2ꢃ
SoftAp
have the matching password from joining the network, while
encrypting the data traveling between authorized devices.
• WPA2-PSK: This is also for home and small business use.
• WPA-PSK/WPA2-PSK: When selecting this mode, the AP supports
both WPA-PSK and WPA2-PSK.
Encryption Type: Five options are available in the drop-down menu.
• Not Use: Disables the encryption mode.
• WEP: Enables WEP Data Encryption. When the item is selected,
continue setting the WEP Key.
• TKIP: The Temporal Key Integrity Protocol changes the temporal
key every 10,000 packets (a kind of message transmitted over a
network.) This ensures much greater security than standard WEP
security.
• AES: Advanced Encryption Standard was developed to provide the
highest degree of security and authenticity for digital information.
It’s the most advanced solution defined by IEEE 802.11i for security
in a wireless network.
• BOTH: In this mode, the AP supports both TKIP and AES.
WPA Pre-Shared Key: The WPA-PSK key can be 8 to 64 characters in
length and can be letters or numbers. This same key must be used on
all the wireless stations in the network.
Group Rekey Interval: This function is available when using WPA-PSK
and WPA2-PSK encryption algorithms.
WEP Key (Key#1–4): WEP keys are used to encrypt data transmitted
in the wireless network. There are two types of key length: 64-bit and
128-bit. Assign a default encryption key (Key#1 to Key#4) by clicking
on the corresponding radio button. To fill in each text field:
• 64-bit: Input 10-digit hex values (in the A-F, a-f and 0-9 range) or
5-digit ASCII characters (a-z and 0-9) as the encryption keys.
For example: “0123456aef” or “test1.”
• 128-bit: Input 26-digit hex values (in the A-F, a-f and 0-9 range) or
13-digit ASCII characters (“a-z” and “0-9”) as the encryption keys.
For example: “01234567890123456789abcdef“ or “administrator.”
Show Password: The password will be displayed in clear text instead
of with asterisks.
2ꢄ
SoftAp
ACCESS CONTROL
This screen lets you configure the access control policy used within the
access point.
MAC Table
Access Policy: Select from the drop-down menu.
• Disable: Disables the MAC address filtering function.
• Allow All: Only wireless adapters with a MAC address on the access
list can connect to the AP.
• Reject All: Wireless adapters with a MAC address on the access
list will be prevented from connecting to the AP.
MAC Address: This is the unique 12-digit hexadecimal identification for
hardware devices in the network.
Access List: Displays all the MAC address that have been added.
• Add: Add the MAC address to the access list.
• Delete: Delete the selected MAC address from the access list.
• Remove All: Remove all MAC addresses from the access list.
Apply: Click to apply the setting change(s).
2ꢅ
SoftAp
MAC TABLE
This screen displays details of the wireless adapters connected to the AP.
MAC Table
MAC Address: The addresses of wireless adapters connected to the AP.
AID: The Association ID of the current connection.
Power Saving Mode: The supporting status of the power saving mode
of the connected wireless adapter.
EvENT LOG
This screen displays event times and messages. Click “Clear” to remove
displayed information.
MAC Table
2ꢆ
SoftAp
STATISTIcS
This screen displays the transmit and receive statistical information of
the AP. Click “Reset Counters” to clear the data.
MAC Table
ABOUT
This screen displays basic information about the utility, including the
MAC address.
MAC Table
ꢀ0
SoftAp
specificAtions
General
• Standards: IEEE 802.11b, IEEE 802.11g, 2.4 GHz
• Interface: Hi-Speed USB 2.0
• Chipset: Ralink RT2571 (RT73)
• Frequency band: 2.4000 – 2.4835 GHz (Industrial Scientific Medical
Band)
• Modulation: OFDM with BPSK, QPSK, 16QAM, 64QAM (11g) BPSK,
QPSK, CCK (11b)
• Data rate: 54/48/36/24/18/12/11/9/6/5.5/2/1 Mbps auto fallback
• Effective throughput: 35 Mbps with Packet-OVERDRIVE Turbo Mode
• Security: 64/128-bit WEP data encryption, WPA (TKIP with IEEE
802.1x) and WPA2 (AES with IEEE 802.1x)
• Transmit power: 15 dBm +/- 2 dBm
• Certification: FCC Class B, CE Mark
Environmental
• Dimensions: 95 (H) x 52 (W) x 38 (L) mm (3.7 x 2.0 x 1.5 in.)
• Extension cable length: 1.5 m (5 ft.)
• Weight: 0.22 kg (0.48 lbs.)
• Operating temperature: 0 – 40° C (32 – 104°F)
• Storage temperature: 0 – 70° C (32 – 158°F)
• Operating humidity: max. 95% RH, non-condensing
System Requirements
• Desktop PC with Pentium 300 MHz-compatible processor or higher
• Windows 98SE/Me/2000/XP/2003/Vista, Linux and MacOS X
• WPA2 encryption requires Windows 2000/XP/2003/Vista
• Available Hi-Speed USB 2.0 port
• Compatible with all 802.11g/b-compliant wireless products
Package Contents
• Wireless G USB Adapter
• USB extension cable with desktop stand
• Setup CD and user manual
ꢀ1
SpECIFICATIONS
INTellINeT NeTWoRK SolUTIoNS™ offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com.
Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.
|