SERVICE SUPPLEMENT
TO 39132.0000
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
39132.0003A 04/12 ©2010 Bunn-O-Matic Corporation
INTRODUCTION
This equipment will brew a half-gallon batch of coffee into an awaiting dispenser. It can be easily
configured for 120V 15 amp, 120/208V 20 amp or 120/240V 20 amp.The brewer may have a hot water
faucet for allied beverage use. It is only for indoor use on a sturdy counter or shelf.
CONTENTS
Warranty............................................................................................... 2
Contents .............................................................................................. 3
Programming....................................................................................... 4
Schematic Wiring Diagram............................................................... 10
39132.3 040312
Page 3
PROGRAMMING
PROGRAMMING THE BREWER
The information in this manual covers only the differences between this model and the standard Axiom.
Access to service level 4 is same as standard Axiom.
The following function screens are in order of appearance. Each screen will have instructions on how to access,
and the procedures to program the various functions of the brewer.
IMPORTANT PROGRAMMING NOTES
- READ CAREFULLY -
To exit the programming mode at any time, press and release "ENABLE BREW ON/OFF" switch located on the
front switch panel. The display will return to the MAIN SCREEN.
If none of the programming switches are pressed within one minute during the setup of the brewer, the
programming of the function screen that is being set will be exited and the display will return to the MAIN
SCREEN.
Always remember to place an empty server and funnel under the sprayhead when operating the brewer dur-
ing the set-up of PULSE BREW, CALIBRATE FLOW and testing the brew valve in TEST OUTPUTS.
PROGRAMMING LOCKOUT SWITCH
(Mounted on main control board)
This switch can be set to prevent access to the programming settings of the brewer. Once all the cor-
rect brew settings are programmed, the operator can set the switch to the "LOCK" position to prohibit
anyone from changing the settings.With the switch in the "LOCK" position, the programming menus
can still be accessed to view the current settings. However, no changes will be saved.
LOCK
SET
Disconnect brewer
from power source
before removing any
panel!
REVERSE
FORWARD
READY TO BREW
WATER TEMP: 200°
Push and hold left "hidden"
button to access service
program modes.
39132.3 040312
Page 4
SERVICE PROGRAMMING
Freq&AdjustCaps?
NO YES
DISPLAY BREW TIMES
TEST RFID BOARD
NO YES
NO
YES
GLASS FRESH HRS
(-) .5 (+)
ThermalFresh HRS
FRESHNESS TIMEOUT
NO YES
(-)
2.0
(+)
WARMER MINs PAST
FRESHNESS:
FRESHNESS SCAN
EXPIRATION ALARM
5
NO
DONE
YES
DISABLE
ENABLE
EXPIRATION SECS
ADJUST ALARM
SET DATE/TIME ?
NO YES
(-)
10
(+)
NO VOLUME ? YES
Return To Main Screen
PRE-EXPIRE ALARM
AXIOM
DISABLE
ENABLE
VERSION xx.xx
Displays Model &
Software Version
39132.3 040312
Page 5
SERVICE PROGRAMMING
This allows you to monitor the frequency of the warmer(s) sensing
coils.
Freq&AdjustCaps?
NO
YES
Also allows you to monitor the adjustment capacitors, which are used
to keep the coil frequency at it's nominal value (125.0 khz)
125.0 0000
125.0 0000
* TOP F
* TOP R
Use the "Brewer" button to toggle between screens.
125.0 0000
* MAIN
Press right hidden button to advance to next function.
This allows you to read the "age" of any brewed batch in a particular
carafe (as long as it is equipped with an RFID chip). The sensor coil
will read the chip and brewer will display time of day it was brewed.
DISPLAY BREW TIMES
NO
YES
This screen will automatically scroll through all warmers.
Press right hidden button to advance to next function.
MAY 10
2010
MAIN 10:00:00 AM
This allows you to monitor individual sensing coils and RFID board.
TEST RFID BOARD
NO
YES
RFID CIRCUIT BOARD
VERSION # xx.xx
CONTINUED
39132.3 040312
Page 6
SERVICE PROGRAMMING
PRESS ANY SWITCH
TO EXIT
If a carafe is placed on a particular warmer, a "box" will appear next
to it's indicator. If the box is filled (solid) it's not expired yet. If the
box is empty, the time is expired. See example: MAIN = expired; Top
Front = not expired; Top Rear = expired.
10:00:00 AM
M
TF
TR
Press right hidden button to advance to next function.
Enables the "FRESHNESS ALERT!" message and sets the
expiration time. The expiration time is the amount of time the
product is allowed to sit in the glass decanter before an alert
message is displayed. DEFAULT: .5
GLASS FRESH HRS
(-) .5 (+)
Range: OFF/0.5 - 4.0 hrs
Enables the "FRESHNESS ALERT!" message and sets the
expiration time. The expiration time is the amount of time the
product is allowed to sit in the thermal server before an alert
message is displayed. DEFAULT: 2.0
ThermalFresh HRS
(-)
2.0
(+)
Range: OFF/0.5 - 4.0 hrs
Sets the amount of time the warmers will turn off after an alert
message is displayed. DEFAULT: 5
Range: OFF/1 - 30 min
WARMER MINs PAST
FRESHNESS:
5
Allows brewer to continually scan the warmer sensor coils and
display freshness times.
FRESHNESS SCAN
NO
DONE
YES
Enable/Disable beeper.
EXPIRATION ALARM
DISABLE
ENABLE
CONTINUED
39132.3 040312
Page 7
SERVICE PROGRAMMING
Sets the amount of delay between alarm beeps.
EXPIRATION SECS
(-) 10 (+)
Select "YES" to adjust beeper volume.
ADJUST ALARM
NO VOLUME ? YES
Press "+" to increase volume, or "-" to decrease.
ADJUST ALARM 5
-
+
Select "YES" to set date and/or time.
SET DATE/TIME ?
NO YES
Press "+" to scroll year forward, or "-" to scroll year back.
Press "+" to scroll month forward, or "-" to scroll month back.
YEAR 2010
DONE
(-)
(-)
(-)
(+)
(+)
(+)
MONTH MAY
DONE
Press "+" to scroll day forward, or "-" to scroll day back.
DAY
DONE
10
CONTINUED
39132.3 040312
Page 8
SERVICE PROGRAMMING
Press "+" to scroll hour forward, or "-" to scroll hour back.
HOUR 10 AM
DONE
(-)
(-)
(-)
(+)
(+)
(+)
Press "+" to scroll minute forward, or "-" to scroll minute
back.
MINUTE 00
DONE
Press "+" to scroll seconds forward, or "-" to scroll seconds
back.
SECOND 00
DONE
Enable/disable the 5 minute warning beep for a carafe about
to expire.
PRE-EXPIRE ALARM
DISABLE ENABLE
EXIT
39132.3 040312
Page 9
L1
N
L2
SCHEMATIC WIRING DIAGRAM
AXIOM BrewWISE-DV
Earth Ground
GRN
MAIN ON/OFF SWITCH
(Late Models only)
Chassis Ground
BLK-14
SELECTOR
SWITCH
LIMIT
THERMOSTAT
WHI-14
WHI/VIO-14
TANK HEATER
1425W
BLU-14
BLK-14
BLU-14
BLK-14
TANK HEATER
RED-14
OPTIONAL FAUCET HEATER
2268W
WHI
WHI
BREW STATION WARMER
(CONTROLLED BY ENABLE BREW SW)
REFILL
BLK
WHI/RED
WHI
WHI
WHI/BLU
SOL
DISPENSE
SOL
BLU-14
BLK-14
WHI
WHI
WHI/GRN
RELAY
J1-1
C
O
N
T
WHI
BLK
(TOP WARMERS)
R
O
L
P2
FRONT WARMER
P1
BRN/BLK
BRN/BLK
WHI
BRN/BLK
WHI/BLU
WHI/RED
YEL
WHI/VIO
VIO
WHI
J1-5
P
C
B
O
A
R
D
W
H
I
P1, P2, &
P3 ARE
PINS OF A
POLARIZED
THREE-PIN
CONNECTOR.
P3
P2
REAR WARMER
VIO
WHI/GRN
J1-10
J13-1
(LEFT WARMER)
FRONT WARMER
P1
YEL
WHI
WHI
J5-1
J6-1
J7-1
BRN
RED
ORN
YEL
GRN
BLU
J1-1
J1-5
TOP REAR WARMER SENSOR
LOWER WARMER SENSOR
W
H
I
REAR WARMER
P3
WHI/VIO
J13-5
TOP FRONT WARMER SENSOR
RFID
BOARD
RED
BLK
J12-1
BEEPER
CONTROL SWITCH ASSY CODES
2 WARMERS 2 WARMERS 2 WARMERS
CONTROL SWITCH ASSY
(NOTE – ALL WARMERS ARE NOT
AVAILABLE ON ALL MODELS!)
ON LEFT
A3
ON TOP
A3
ON RIGHT
A3
STATIC
SHIELD
BREW STATION
LEFT FRONT
LEFT REAR
J2-1
J2-5
A2
A1
TOP FRONT
TOP REAR
A5
A6
RIGHT FRONT
RIGHT REAR
START BREW
LEFT HIDDEN
RIGHT HIDDEN
“DIGITAL”
A5
A6
A4
B1
B2
D1
D2
D3
A4
B1
B2
D1
D2
D3
A4
B1
B2
D1
D2
D3
B1 A6 D1
A3 D2
A4 D3 A5 B2 A2
A1
J2-10
“BREWER”
“CONTROL”
BRN
GRN
BLU
J3-1
J3-3
WHI
BLK
J9-1
LEVEL PROBE
(SHORT)
LEVEL PROBE
(LONG)
t°
120V AC 2 WIRE
120/208V AC 3 WIRE
120/240V AC 3 WIRE
SINGLE PHASE
29077.0021A 06/10 ©2010 BUNN-O-MATIC CORPORATION
39132.3 040312
Page 10
|