Make every picture perfect
SP4200 VARIABLE POWER
STUDIO FLASH SET
SP4200 Flash Studio Kit
Thank you for your purchase of the SP4200 Flash Softbox Studio
kit. This manual has been written to help you with the assembly,
operating procedures and accessories. Square Perfect's SP4200
Flash Kit is manufactured with the finest material available. Your
flash kit will provide many years of quality service with proper care
andhandling.
Please read this manual carefully before use, and keep it handy
for use during break down of equipment. Please read and heed all
safety precautions listed in this manual. To order spare bulbs
or replacement parts, contact us at [email protected].
Also check out our extended line of photo equipment now
available.
Flash Studio Kit Includes:
Nylon Carry Case. Compartmentalized for easy use
1x2 SP200 lamp body.
12' power cord.
1
Four leaf barndoor.
1x3 Four panel softbox set.
with lamp connector.
Electronic radio trigger /
receiver with sync cord and
adaptors.
1x1 Flat reflector for creative
fill techniques,
includes carry case
1x1 Complete backdrop stand with
carry case
1x1 Snoot will direct light to
exact spot without
affecting surrounding
1x1 Umbrella - double
layered reflective
inside, light proof
backing.
1 set Red, blue, yellow frosted
and honeycomb filter.
area.
1x3 SP8061 professional duty
adjustable light stand.
Stand extends from 39" to 8'1/2".
1x3 Four panel softbox set.
with lamp connector.
1x1 Varigated dye backdrop
1x1 Black backdrop
1x1 White backdrop
1x1 Twelve foot boom with adjustable
weight counter balance bag.
Specifications:
SP200 Lamp Head Operation:
Power Input : AC110-130 volt, 50 Hz
Flash Power : 200w (joule) in full
Guide No. : GN45
9.
10.
Color Temperature : 5600K
Flash-Tube Lifetime : over 8,000 typical flashing
Flash Power Setting : 1/32 to full
Recharge Time : 2 seconds in full
Flash Duration : 1/600 sec.; 1/1000 sec.
Slave Range : 35ft /10m
9.
4.
3.
5.
8.
2.
1.
11.
6.
Lighting Range : 55 degree
Modeling Power : Halogen 100w
Synch Voltage : 5 volt
12.
7.
8.
Fuse : 6A
Dimension : 4" x 7-1/2"
Weight : 1.8 Lb (800g)
5. Flash test.
9. Flash digital readout.
10. Remote button.
11. Flash ring.
1. On/Off electric supply.
2. Variable flash buttons.
3. On/Off variable, model lamp.
4. On/Off flash ready beep.
6. Sync receptacle.
7. Safety fuse.
8. AC receptacle.
12. Model lamp.
SAFETY PRECAUTIONS:
•Become thoroughly familiar with this product before use. Run
through at least one practice assembly and breakdown before
you schedule a shoot.
• Make sure that the main voltage corresponds to that stated on
the SP160 lamp. Account for number of lamps in use.
• Never leave the lighting unsupervised when in use. Keep
children or incompetent persons away from lighting equipment.
• If the lamp or the cord show sign of wear or damage, it should
be replaced or repaired by a qualified electrician before use.
• Wait until the bulb is completely cool before touching or
removing it.
• Never use the SP160 lamp outside in a wet environment.
• Never move the appliance by pulling the cord. Make sure the
cords do not come in contact with halogen bulb. Do not wind
the cord around the appliance.
• Stand the SP160 on a flat surface only to prevent toppling.
• Do not touch the metal parts on the lamp while in use, these
metal parts will become very hot.
Softbox Assembly:
4. Next insert the fourth rod
into the SP 4" ring. Note: Keep
the velcro flaps at the ring
open to allow sufficient slack.
5. Insert the forth rod into the
pocket on the velcro strap.
1. Pictured is the SP4" lamp ring
connector shown with the
large end of the flex rod inserted.
3. With three rods inserted into
the ring and corners, fold the
SP 4" ring into the tent.
2. Small end of flex rod fits into
corner pocket on the softbox
tent.
7. Now close the velcro flaps
as shown in the picture.
6. Push the velcro strap into
place just below the lip of the
tent. Note: the rods take a good
deal of force to flex into position.
10. Attach the outer diffusion
lens to velcro patches on
the outer edges.
8. The SP 4" ring can now be
attached to the SP 160 flash unit.
DO NOT over tighten.
9. Next attach the inner diffusion
lens with the velcro straps.
Technical Notes for the electronic radio trigger device:
TheSP Flash Kit is shipped with theDRT-2G electronic
radio flash triggering devicefor yourconvenience.
It is an easy to use device that will give you extra
control in the photographic studio environment. The
DRT-2G is designed to work with a variety of flash
units. We provide a wide range of sync cord adaptors
tofit mostpopular brands.
The DRT-2G trigger has two channels and uses a 23A
battery (installed). The DRT-2G receiver uses two AAA
batteries(notincluded).
4.Switch the remote flash unit power
switch to the ON position with the DRT-2G
receiver attached. Push the test button
on the DRT-2G trigger, it should trigger
theremoteflash unit.
1.To use the DRT-2G trigger device, first
slide the trigger into the hot shoe found
on top on your camera. If a hot shoe is not
available, use the sync cord attachment
found ontheside of thetrigger device.
2.Attach the receiver to a remote flash unit.
Use the proper sync cord adaptor
provided, plug intosynccord socket.
5.To change channels on the DRT-2G
trigger, slide the channel switch on the
side of the trigger device to the opposite
position. Next press the power switch on
the receive unit twice to reset the
receiver.
3.Switch the receiver unit ON/OFF button to
the ON position. Press the test button
located on the top of the trigger unit. You
will see a twinkling of the LED on the
receiver unit. This indicates the trigger is
working properly and is locked-in on a
working channelof thereceiver.
To order spare bulbs or replacement parts,
contact us at [email protected]. Also check
outourextendedlineof photoequipment.
|