KCA-R70FM/Cover for K 02.7.2 11:16 AM Page 1
FM MODULATOR SYSTEM
KCA-R70FM
INSTRUCTION MANUAL
SYSTEME A MODULATION DE FM
MODE D’EMPLOI
SISTEMA DE MODULADOR FM
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you
obtain the best performance from your FM modulator system.
For your records
Record the serial number, found on the back of the unit, in the spaces desig-
nated on the warranty card, and in the space provided below. Refer to the
model and serial numbers whenever you call upon your KENWOOD dealer for
information or service on the product.
Model KCA-R70FM Serial number
©PRINTED IN JAPAN B64-2432-00/00 (K)(+)
'03/12 11 10 9 8 7 6 5 4 3 2 1 '02/12 11 10 9 8 7 6
KCA-R70FM_U.S 02.7.2 11:20 AM Page 3
Safety Precautions
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
• To prevent a short circuit when replacing a
fuse, first disconnect the wiring harness.
IMPORTANT INFORMATION
About the disc changer to be
connected:
To connect a disc changer having the "O-N"
switch to this unit, set the "O-N" switch to "N".
Note that none of the KDC-C100, KDC-C302,
C205, C705, and non-Kenwood CD changers
can be connected.
You can damage both your unit and the CD
changer if you connect them incorrectly.
Precautions when connecting disc changers
released in 1997 or earlier.
The optional switching adapter KCA-S210A is
necessary to connect a disc changer that is
not equipped with the "O-N" switch except
KDC-C100, KDC-C302, C205 and C705.
2WARNING
Take the following precautions to
prevent fire and avoid personal injury:
• When extending the ignition wire, battery
wire, or ground wire, use 0.75mm2 (AWG18)
or larger automotive grade wire to avoid wire
deterioration or damage to the covering.
• Check that no metal objects (coins, tools,
etc.) are left inside the unit to avoid short
circuits.
• If you smell or see smoke, turn the power
off immediately and consult your Kenwood
dealer.
• Do not touch the liquid crystal fluid if the
LCD is damaged or broken due to shock. The
liquid crystal fluid may be dangerous to your
health or even fatal.
NOTE
• If you have difficulty in installing this unit in
your vehicle, contact your Kenwood dealer.
• If it doesn’t seem to be working properly,
first press the Reset button. If the
malfunction persists, consult your Kenwood
dealer.
Cleaning the Unit
If the front panel gets dirty, turn off the
power and wipe the panel with a dry silicon
cloth or soft cloth.
If the liquid crystal fluid from the LCD
contacts your body or clothing, wash it off
with soap immediately.
Reset button
2CAUTION
• Some car stereos cause the sound of the
tuner to make for a moment when an
engine is activated.
• The reception of the tuner may be reduced
a little if the KCA-R70FM is used.
• If the sound is lower than the tuner sound,
raise up the volume level of the CD/MD
with using the receiver.
2CAUTION
Do not use hard cloths or paint thinner,
alcohol, or other volatile solvents. These may
damage external surfaces or remove
indicator characters.
Take the following precautions to
keep the unit in proper working order.
• Be sure the unit is connected to a 12V DC
power supply with a negative ground
connection.
• Do not open the top or bottom cover.
• Do not install the unit in places it is exposed
to direct sunlight, high heat or humidity,
water may splash over it, or dust exists.
• Do not use your own screws. Use only the
screws provided. If you use the wrong
screws, you could damage the unit.
— 3 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 4
Safety Precautions
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications
to this equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction manual.
The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
NOTE
This Class B digital apparatus complies with
Canadian ICES-003.
— 4 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 5
General features
Set the car radio FM station to 88.3 MHz. See Page 13 for
more information on changing the transmission frequency.
Power
SRC
Turning ON the Power
Press the [SRC] button.
Turning OFF the Power
Press the [SRC] button for at least 1 seconds.
The FM modulator is turned OFF and the radio can be heard.
• Be sure to turn down the volume whenever you listen to the
radio or a cassette tape after stopping the disc play.
• During the disc play is being conducted, you are not able to
receive ordinary Radio broadcasting because antenna output is
switched into compact disc player‘s side.
Switching Modes
Press the [SRC] button.
Source required
Display
Sirius
"SIRIUS"
CD/MD auto-changer
"CHANGER"/"CHANGER-1"/
"CHANGER-2"
Auxiliary input
Off
"AUX"
For Auxiliary input one of the below optional accessories is
necessary.
- KCA-S210A
- CA-C1AX
- CD changer with an Auxiliary input function installed.
— 5 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 6
Sirius satellite radio tuner features
Selecting Sirius Mode
Press the [SRC] button.
Select the "SIRIUS" display.
¢
u
SRC
SRCH
• You need to subscribe to SIRIUS to receive the service by Sirius
Satellite Radio. Consult SIRIUS if "CALL 888-539 SIRIUS TO
SUBSCRIBE" appears.
• It may take a little time to start receiving after you selected the
SIRIUS source.
• If the signal receiving fails, "ACQUIRING SIGNAL" appears.
4
Switching Seek Mode
d
SEEK
DISP
# 1-6
Sets the seeking mode.
Press the [SEEK] button.
Each time the button is pressed the Seek mode switches as
shown below.
Preset station number
Band display
Channel number
Display
Operation
"SEEK 1"
"SEEK 2"
Normal manual seeking control.
Search in order of the channels in the
Preset memory.
SCAN indicator
You cannot operate this unit during switching Channel or Category.
Selecting the Preset Band
Press the [u] button.
Each time the button is pressed the preset band switches
between the SR1,SR2,SR3, and SR4.
— 6 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 7
2 Release it when the channel you want to listen to is received
Channel Preset Memory
Putting the channel in the memory.
Press the [SEEK] button for at least 1 second.
1 Select the preset band
Press the [u] button.
2 Select the channel to put in the memory
Channel Search
Press the [4] or [¢] button.
You can switch from Up/Down of Channel in a category being
selected to Previous/Next of Category that includes Channel
being received and vice versa.
3 Put the channel in the memory
Press the [#1] — [#6] button for at least 2 seconds.
The preset number display blinks 1 time.
On each band, 1 channel can be put in the memory on each [#1]
— [#6] button.
1 Enter Channel Search mode
Press the [SRCH] button.
2 Select the Category
Only the channel number is stored. Category information is not
stored.
Press the [u] or [d] button.
3 Select the Channel
Press the [4] or [¢] button.
Canceling Channel Search
Press the [SRCH] button.
Preset Tuning
Calling up the channels in the memory.
You cannot operate this unit until all the Category information is
acquired.
1 Select the preset band
Press the [u] button.
2 Call up the channel
Press the [#1] — [#6] button.
Channel Scan
Scanning for the channel you want to listen to.
1 Start Channel Scan
Press the [SEEK] button for at least 1 second.
"SCAN" indicator is ON.
— 7 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 8
Sirius satellite radio tuner features
Switching Display
Direct Access Tuning (Function of remote)
You can display various kinds of text data transmitted from
broadcasting stations by switching as follows.
Entering the channel and tuning.
1 Enter Direct Access Tuning mode
Press the [DISP] button.
Each time the button is pressed the display switches as shown
Press the [DIRECT] button on the remote.
2 Enter the channel number
below.
Press the number buttons.
Information
Display
Channel Number
Channel Name
Song Title
Artist Name
Category Name
Album Title
3 Do Channel Search
"CHANNEL"
"SONG"
"ARTIST"
"CATEGORY"
"ALBUM"
Press the [4] or [¢] button.
Canceling Direct Access Tuning
Press the [DIRECT] button on the remote.
• If you make no button operation for 10 seconds, the Direct Access
Tuning mode is automatically canceled.
• You can set up to Channel number 223.
• If there is no signal in the input Channel, "NO CHANNEL" appears.
• If you cannot receive any signal in the input Channel due to a bad
condition on radio wave or another problem, "ACQUIRING SIGNAL"
appears.
— 8 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 9
Disc control features
Playing Disc
Play:
¢
Press the [SRC] button.
6
u
SRC
Select the "CHANGER"/"CHANGER-1"/ "CHANGER-2" display.
Stop the play:
Press the [SRC] button for at least 1 second.
The FM modulator is turned OFF and the radio can be heard.
Pause and play:
Press the [6] (38...Remote) button.
Each time the button is pressed it pauses and plays.
If you press the switch once more, the disc is replayed from
the paused part.
This unit enables control of an MP3-compatible disc auto-changer.
MP3 media formats, refer to the instruction manual of the MP3-
compatible disc auto-changer to be connected.
4
d
SCN
RDM REP
DISP
M.RDM
Fast Forwarding and Reversing
Track time
Track number
Disc number
Fast Forwarding
Hold down on the [¢] button.
Release your finger to play the disc at that point.
Reversing
Hold down on the [4] button.
Release your finger to play the disc at that point.
Indicator
Track Search
Searching for a song on the disc or in the MP3 folder.
Press the [4] or [¢] button.
— 9 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 10
Disc control features
Disc Search
Track/Disc Repeat
Selecting the disc set in the Disc changer.
Press the [u] or [d] button.
Replaying the song, disc in the Disc changer or MP3 folder
you're listening to.
Press the [REP] button.
When it's ON, the "REP" indicator is ON.
Each time the button is pressed the Repeat Play switches as
shown below.
Direct Track Search (Function of remote)
Doing Track Search by entering the track number.
Repeat play
Display
Track Repeat
Disc Repeat
OFF
Track No. blinks.
Disc No. blinks.
—
1 Enter the track number
Press the number buttons on the remote.
2 Do Track Search
Press the [T.UP] or [T.DOWN] button.
Canceling Direct Track Search
Track Scan
Press the [38] button.
Playing the first part of each song on the disc or MP3 folder you
are listening to and searching for the song you want to listen to.
1 Start Track Scan
Direct Disc Search
Press the [SCN] button.
"SCAN" indicator is ON.
(Function of disc changers with remote)
Doing Disc Search by entering the disc number.
2 Release it when the song you want to listen to is played
Press the [SCN] button.
1 Enter the disc number
Press the number buttons on the remote.
2 Do Disc Search
Random Play
Play all the songs on the disc or MP3 folder in random order.
Press the [+] or [–] button.
Canceling Direct Disc Search
Press the [38] button.
Press the [RDM] button.
Each time the button is pressed Random Play turns ON or OFF.
When it's ON, the "RDM" indicator is ON and the track number
blinks.
Input "0" to select disc 10.
When the [¢] button is pressed, the next song select starts.
— 10 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 11
Text/Title Scroll
Scrolling the displayed CD text, or MD title.
Press the [DISP] button for at least 1 second.
Magazine Random Play
(Function of disc changer)
Play the songs on all the discs in the disc changer in random
order.
Press the [M.RDM] button.
Each time the button is pressed the Magazine Random Play turns
ON or OFF.
Switching Display
Switching the information displayed.
When it's ON, the "RDM" indicator is ON and the track and disc
number blink.
Press the [DISP] button.
Each time the button is pressed the display switches as shown
When the [¢] button is pressed, the next song select starts.
below.
Information
Display
P-Time
A-Time
Disc title
Track title
Folder Search (Function of MP3)
Selecting the folder you want to listen to.
"DISC TITLE"
"TRACK TITLE"
1 Enter Folder Search mode
Press the [6] (38...Remote) button.
File No. display changes to Folder No. display during the Folder
Search mode.
2 Select the folder
Press the [u] or [d] button.
With the [d] button you move to the previous folder, and with
the [u] button to the next folder.
3 Decide the folder to play
Press the [6] (38...Remote) button.
The Folder Search mode releases, and the MP3 in the folder
being displayed is played.
— 11 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 12
Menu system
Menu System
The Menu system basic operation method is explained here. The
reference for the Menu items and their setting content is after
this operation explanation.
MENU
u
1 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
2 Select the menu item
Press the [u] or [d] button.
3 Set the menu item
Press the [4] or [¢] button.
You can continue by returning to step 2 and setting other items.
¢
4
d
4 Exit Menu mode
Press the [MENU] button.
When other items that are applicable to the basic operation method
above are displayed afterwards their setting content chart is
entered.
— 12 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 13
Changing the Transmission Frequency
Dynamic control
Select the frequency.
Settingt the Dynamic control.
Display
Setting
Display
Value
"D-CONT ON"
"D-CONT OFF"
The dynamic control is ON.
The dynamic control is OFF. (Initial setting)
"T-FREQ 87.7"
"T-FREQ 87.9"
"T-FREQ 88.1"
"T-FREQ 88.3"
"T-FREQ 88.5"
"T-FREQ 88.7"
"T-FREQ 88.9"
"T-FREQ 89.1"
"T-FREQ 89.3"
"T-FREQ 89.5"
"T-FREQ 89.7"
"T-FREQ 89.9"
87.7 MHz
87.9 MHz
88.1 MHz
88.3 MHz (Initial setting)
88.5 MHz
88.7 MHz
88.9 MHz
89.1 MHz
89.3 MHz
The unit comes with the prevention of distortion function to
reduce sound distortion.
If the sound is distorted severely, press the [4] or [¢] button
on the display unit and then set the function to "ON". If the
prevention of distortion function is set to "ON", the sound
extension is reduced.
If a disc with a high recording level is used, the sound may distort
even if the prevention of distortion function is set to "ON". In this
case, reduce the modulation level.
89.5 MHz
89.7 MHz
89.9 MHz
Some car radios cannot receive a 87.7 MHz frequency.
Text Scroll
Setting the displayed text scroll.
Display
Setting
Modulation level
Select the modulation level.
"SCROLL MANU"
"SCROLL AUTO"
Doesn't scroll.
Scrolls when the display changes.
Display
The texts scrolled are shown below.
• CD text
• Song title/ Artist name/ Album title/ Category name
• MD title
"MOD LEVEL 1"
"MOD LEVEL 2" (Initial setting)
"MOD LEVEL 3"
"MOD LEVEL 4"
— 13 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 14
Menu system
Sirius ID (ESN)
<When the KTC-SR901 is connected>
Sirius ID (Electronic Serial Number) is displayed.
— 14 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 15
Basic Operations of remote
Loading and Replacing the battery
Use two "AAA" batteries.
Slide the cover while pressing downwards to remove it as
illustrated.
SRC
RDM
Insert the batteries with the + and – poles aligned
SRC button
RDM button
REP button
properly, following the illustration inside the case.
D.UP
REP
+
-
button
button
CH-
SEARCH
D.DOWN
38/CH SEARCH
button
T.DOWN
T. DOWN button
D.REPEAT button
SCAN button
T.UP
T. UP button
D.REPEAT
SCAN
M.RDM
M.RDM/DIRECT
DIRECT
button
1
4
7
2
5
8
0
3
2WARNING
Store unused batteries out of the reach of children. Contact a doctor
immediately if the battery is accidentally swallowed.
6
9
Number buttons
• The provided batteries are intended for use in operation
checking, and their service life may be short.
• When the remote controllable distance becomes short, replace
both of the batteries with new ones.
REMOTE CONTROL UNIT
RC-513
• A portion of the operations may not be possible, depending on
the unit that is connected.
Do not set the remote on hot places such as above the dashboard.
Basic operations
[SRC] button
Each time the button is pressed the source switches.
— 15 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 16
Basic Operations of remote
In Sirius source
In Disc source
[+] buttons
[T.UP]/ [T.DOWN] buttons
Select the band.
Doing track forward and backward.
Each time the [+] button is pressed it switches between the
SR1, SR2, SR3, and SR4 bands.
[+]/ [–] buttons
Doing disc forward and backward.
[T.UP]/ [T.DOWN] buttons
Tune up or down the channels.
[38] button
Each time the button is pressed the song pauses and plays.
Number buttons
Press buttons [#1] — [#6] to recall preset channels.
[REP] button
Each time the button is pressed Track Repeat function turns ON
[DIRECT] button
or OFF.
Enters and cancels the <Direct Access Tuning> (page 8) mode.
[D.REPEAT] button
[CH SEARCH] button
Each time the button is pressed Disc Repeat function turns ON
Enters and cancels the <Channel Search> (page 7) mode.
or OFF.
[SCAN] button
[RDM] button
Each time the button is pressed Channel Scan turns ON or OFF.
Each time the button is pressed Random Play turns ON or OFF.
[M.RDM] button
Each time the button is pressed Magazine Random function
turns ON or OFF.
[SCAN] button
Each time the button is pressed Trak Scan function turns ON or
OFF.
Number buttons
When in <Direct Track Search> (page 10) and <Direct Disc
Search> (page 10), enter the track/disc number.
— 16 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 17
Accessories
Installation Procedure
1. To prevent a short circuit, remove the key from the ignition and
External view
Number of items
disconnect the - battery.
2. Make the proper input and output wire connections for each unit.
3. Connect the wiring harness wires in the following order: ground,
battery, ignition.
1
................................................2
................................................1
................................................1
4. Install the unit in your car.
5. Reconnect the - battery.
6. Press the reset button.
2WARNING
2
3
When drilling a hole in the car chassis to install the unit, check
first that nothing is on the other side.
2CAUTION
• If the fuse blows, first make sure the wires aren’t touching to
cause a short circuit, then replace the old fuse with one with
the same rating.
• Do not let unconnected wires or terminals touch metal on the
car or anything else conducting electricity. To prevent a short
circuit, do not remove the caps on the ends of the
unconnected wires or the terminals.
The use of any accessories except for those provided might result in
damage to the unit. Make sure only to use the accessories shipped with
the unit, as shown above.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Insulate unconnected wires with vinyl tape or other similar
material.
• Some disc changers require optional equipment for connection.
See the section on "Safety Precautions" for details.
— 17 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 18
Connecting Wires to Terminals
CD/MD auto-changer /
Sirius satellite radio tuner
Display unit
Output
Control output
Changer connection wire
Control input
CD/MD auto - changer input
O-N selection switch
O N
"N"
FM modulator unit
FM/AM antenna input
FM/AM antenna output
Antenna plug
for automobile
Car stereo
with FM tuner
Ignition key
switch
ACC
Ignition wire + (Red)
Car fuse box
Battery wire + (Yellow)
Ground wire (Black) - (To car chassis)
Battery
2WARNING
Do not install an antenna of radio equipment or
distribute the antenna wire near the changer output
wire, for this could cause malfunction with this unit.
To prevent fire when the ignition wire (Red) or battery wire
(Yellow) is short-circuited by coming into contact with the
vehicle chassis (ground), only connect the power supply after
making the fuse box connections.
2CAUTION
Be sure to press the reset button after installation.
— 18 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 19
■
If you want to connect disc changers released in 1997 or earlier
Display unit
Control output
Connection wire
CD/MD auto - changer input
"TO CHANGER"
"TO HEAD UNIT"
Control input
Sirius satellite
radio tuner unit
FM modulator unit
]“N”
Connection wire
"TO HU"
CD/MD auto-changer
Output
O
N
OFF ON
AUX
PROTOCOL
SWITCH
AUX
IN
SWITCH
KCA-S210A
Changer connection wire
"TO CHANGER1"
•Set the PROTOCOL selection switch to the "N" position.
•The KCA-S210A must be connected to the Sirius satellite
radio tuner unit if they are connected at the same time.
•Up to two units of the Sirius satellite radio tuner unit or
disc autochanger can be connected at the same time.
— 19 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 20
Installation
■
■
Installation of Display unit
Installation of FM modulator unit
• Installation without using the trim mount plate 3
2CAUTION
1
Attach one strip of Velcro to the
slanted-line of the the display
units as shown to the left, and
attach the other strip of Velcro
to the parts where you wish to
attach the display units.
Display unit
Take sufficient care so
that the wires are not
caught under the seat.
If they are caught, they
may break.
Then, put velcros together and
install the display units.
φ 3
2
• Installation using the trim mount plate 3
Install the FM modulator unit beneath the front seat using
Metal fixture and Bind head screw as shown in the above
figure.
Display unit
3
Pass the wire from the display unit through the hole on the
trim mount plate and push fit the display unit into the trim
mount plate until it locks.
2CAUTION
• Be sure not to place the unit on such place as where it is
exposed to direct sunlight and temperature eventually rises.
It results in the deformation of the case.
• Depending on the installing location, the display unit may
not be able to receive the signals from the controller unit.
Install them after confirming that the signals can be
received.
• Install the unit in such a way that it does not disturb driving.
— 20 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 21
Troubleshooting Guide
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
Sirius source
? The Sirius mode cannot be selected.2
✔
✔
✔
The Sirius connection wire is not connected.
☞ Use the Sirius connection wire to connect the control unit and the
Sirius satellite radio tuner.
General
Connect the power supply of the Sirius satellite radio tuner.53
☞ Connect the battery wire and ground wire to the Sirius satellite
radio tuner.
? The power does not turn ON.01
✔
The fuse has blown.
☞ After checking for short circuits in the wires, replace the fuse with
one with the same rating.
The Sirius satellite radio tuner is not connected properly.55
☞ Connect the Sirius satellite radio tuner directly to this unit.
✔
No ACC position on vehicle ignition.02
☞ Connect the same wire to the ignition as the battery wire.
? No sound can be heard, or the volume is low.58
✔
The input/output wires or wiring harness are connected incorrectly.
☞ Reconnect the input/output wires and/or the wiring harness
correctly.
? Nothing happens when the buttons are pressed.04
✔
The computer chip in the unit is not functioning normally.
☞ Press the Reset button on the display unit (page 3).
? No broadcast can be received2
✔
The Sirius antenna is not connected.
? No sound or sound is low.52
☞ Connect it properly.
✔
✔
✔
The O-N selection switch of the disc changer is not set properly.
☞ Set the O-N selection switch to "N" position.
✔
No subscription is established.53
☞ Subscribe to SIRIUS.
The radio volume is sets to the minimum level.3
☞ Turn the radio volume up.
? No sound is heard even though the information concerning the
The input/output wire or wiring harness is connected incorrectly.55
☞ Connect the input/output wire or wiring harness correctly. See
"Connecting Wires to Terminals" (Page 18,19).
Sirius satellite radio tuner is displayed.67
✔
✔
✔
The radio volume is sets to the minimum level.
☞ Turn the radio volume up.
The microcomputer does not function correctly.68
☞ Press the Reset button of the display unit.(Page 3)
? Sound distortion.67
The signal levels differ depending on sources.
☞ Change the Modulation level / Dynamic control setting. (Page 13)
✔
The system is not connected properly.69
☞ Connect the system properly. See <Connecting Wires to
Terminals>. (Page 18,19)
? Nothing appears on the display.04
✔
The control output of the display unit is not connected properly.
☞ Connect the control output properly.
— 21 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 22
Troubleshooting Guide
Disc source
? Sound skips due to vibration.67
✔
Something is touching the CD/MD auto-changer.
? CD/MD play does not start.52
☞ Keep it away from the CD/MD auto-changer.
✔
✔
✔
CD/MD auto-changer input is not connected to the unit.
☞ Connect the CD/MD auto-changer input to the unit.
✔
The disc is dirty or damaged.68
☞ If sound skips at the same part, the disc is faulty. Check and, if
possible, clean the disc.
Power button is not turned ON.53
☞ Turn the power button ON.
✔
✔
✔
Changer unit is mounted on the a slant.69
☞ Mount the unit so that is level.
The PROTOCOL selection switch of the changer switching unit "KCA-
S210A" is not set properly.54
Changer unit is mounted in an unstable place.8
☞ Mount the unit in a stable place.
☞ Set the PROTOCOL selection switch to "N" position.
? The specified disc does not play, but another one plays instead.52
The angle adjustment switches are set improperly.69
✔
✔
✔
The specified CD is quite dirty.
☞ Clean the CD.
☞ Set the angle adjustment switches to the correct positions.
? Sound quality is poor.67
The CD is upside-down.53
☞ Load the CD with the labeled side up.
✔
The recording of the disc is poor.
☞ Try playing another disc. If the sound is good, the fault was with
the original disc.
The disc is loaded in a different slot from that specified.54
☞ Eject the disc magazine and check the number for the specified
disc.
✔
The disc is dirty or damaged.8
☞ Check and, if possible, clean the disc.
✔
The disc is severely scratched.55
☞ Try another disc instead.
? No sound is heard even though the information concerning the
CD/MD auto-changer is displayed.67
? The specified track will not play.58
✔
✔
✔
The radio volume is sets to the minimum level.
☞ Turn the radio volume up.
✔
Random play or magazine random play has been selected.
☞ Turn off random play or magazine random play.
The microcomputer does not function correctly.68
☞ Press the Reset button of the display unit. (Page 3)
? Cannot play CD-R or CD-RW.60
✔
Finalization processing is not being conducted for CD-R/CD-RW.
The system is not connected properly.69
☞ Connect the system properly. See <Connecting Wires to
Terminals>. (Page 18,19)
☞ Conduct finalization processing with CD recorder.
? Direct Track Search and Direct Disc Search can’t be done.66-1
✔
Another function is ON.
☞ Turn Random Play or other functions OFF.
? Track Search can't be done.66-2
✔
For the discs first or last song.
☞ For each disc, Track Search can't be done in the backward
direction for the first song or in the forward direction for the last
song.
— 22 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 23
MP3 source
? Cannot play an MP3.67
✔
The disc format is not accepted in the unit connected.
☞ Refer to the instruction manual of the disc changer (slave unit) for
creation of compatible formats.
✔
✔
The MP3 has no or invalid track name extension.68
☞ Add the ".MP3" extension to the MP3 track name.
The media is scratched or dirty.69
☞ Clean the media.
? Noise or no sound generated when an MP3 is played.70
✔
The track has the MP3 track name extension while it is not an MP3.
☞ Do not use the ".MP3" extension in non-MP3.
? Takes time before the unit starts playing MP3.71
✔
The medium contains many discs, tracks, and hierarchical levels.
☞ The unit checks all tracks on the loaded medium first. If the
medium has many tracks recorded, it may take a long time for the
unit before it starts playing MP3.
? Fails to play MP3 in the intended order.72
✔
The MP3 tracks were not written by the CD writer in the order in
which you wanted them to be played.
☞ Depending on the CD writer, you may be able to set the order in
which MP3 tracks are to be played by writing them onto a
medium with their track names beginning with play sequence
numbers such as "01" to "99".
? The sound skips when an MP3 is being played.73-1
✔
The media is scratched or dirty.
☞ Clean the media.
✔
The recording condition is bad.73-2
☞ Record the media again or use another media.
? The songs in the selected folder aren’t played in Folder Search
mode.77
✔
There are no MP3 in the selected folder.
☞ Make sure there’s recorded content in the MP3 media.
? The MP3 track search takes time.78
✔
Many tracks are recorded on the media.
☞ When the media directory is complex, the track search can take
time.
— 23 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 24
Troubleshooting Guide
The messages shown below display your systems condition.
EJECT:
No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.E01
➪ Load the disc magazine properly.
NO DISC:
TOC Error:
No disc has been loaded in the disc magazine.E02
➪ Load a disc into the disc magazine.
No disc has been loaded in the disc magazine.E04
➪ Load a disc into the disc magazine.
The CD/MD is quite dirty. The CD is upside-down. The CD is scratched a lot.
➪ Clean the CD/MD and load it correctly.
Nothing has been recorded on the MD.E77
➪ The next MD will automatically be played.
No tracks are recorded on the MD, although it has a title.E77
➪ The next MD will automatically be played.
BLANK DISC:
No Track:
E-12:
Now reading the data in the disc.E77
➪ Normal playback is resumed upon completing the reading of the disc data.
The unit is malfunctioning for some reason.E77
E-77:
➪ Press the reset button on the display unit. If the "E-77" code does not disappear, consult your nearest service center.
Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.E99
➪ Check the disc magazine, and then press the reset button on the display unit. If the "Mecha Error" code does not
disappear, consult your nearest service center.
The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),
stopping all operation.E0d
Mecha Error:
Hold Error:
➪ Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C
(140°F), the disc will start playing again.
ANTENNA ERR: The antenna is not connected correctly.E77
➪ Make sure the antenna is connected correctly and then turn OFF/ON the SIRIUS source or Display unit.
Broadcast cannot be received due to an error in this unit.E77
➪ Turn OFF/ON the SIRIUS source or Control unit, or press the reset button on the Display unit.
The ESN (Electronic Serial Number) is not registered in Sirius satellite radio tuner unit.E77
➪ Consult your nearest service center.
Neither a disc changer nor the Sirius satellite radio tuner is connected.E77
➪ Connect a disc changer or the Sirius satellite radio tuner.
TUNER ERROR:
ESN ERROR:
LINE ERROR:
The number of disc changers and Sirius satellite radio tuners exceeds the limit of connection to this system.E77
➪ Up to two units can be connected. Rearrange your connection not to exceed the limit of the connection.
— 24 —
KCA-R70FM_U.S 02.7.2 11:20 AM Page 25
Specifications
Specifications subject to change without notice.
Modulating Frequency (200KHz STEP) ..........87.7, 87.9, 88.1, 88.3,
88.5, 88.7, 88.9, 89.1,
89.3, 89.5, 89.7, 89.9,
MHz
General
Operating Voltage................................................14.4 V (11 ~ 16 V)
Current consumption ..............................................................1.4 A
Operating Temperature ................................................–10 ~ 50 °C
Size (W × H × D)
Remote Controller ........................................43 × 135 × 22 mm
(1-11/16 × 5-5/16 × 7/8 in.)
Display unit....................................................154 × 43 × 17 mm
(6-1/16 × 1-11/16 × 11/16 in.)
FM modulator unit ........................................150 × 30 × 80 mm
(5-7/8 × 1-3/16 × 3-1/8 in.)
Trim mount plate ..........................................188 × 58 × 18 mm
(7-3/8 × 2-5/16 × 11/16 in.)
Weight
Remote Controller..................................................50 g (0.11 lbs)
Display unit ..........................................................145 g (0.32 lbs)
FM modulator unit ..............................................460 g (1.01 lbs)
— 25 —
|