INSTRUCTION MANUAL
Digital Movie
VPC-C1EX
VPC-C1
Important note
This manual explains how to safely operate the VPC-C1EX and
VPC-C1. Any information regarding only one of these products will
be labeled as such.
Please read these instructions carefully before using the camera. Make
sure to read and understand the section “USING YOUR CAMERA
SAFELY AND CORRECTLY” on pages 7 to 24. Keep this manual in a
safe place for later reference.
Tested to Comply with FCC Standards
FOR HOME OR OFFICE USE
The FCC logo is included in the rating that can be found inside the battery case.
Declaration of Conformity
Model number
Trade Name
: VPC-C1
: SANYO
Responsible party: SANYO FISHER COMPANY
Address
Telephone No.
: 21605 Plummer Street, Chatsworth, California 91311
: (818) 998-7322
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
eFOR CANADIAN USERS
This Class B digital apparatus complies with Canadian ICES-003.
Conformity to EC Directives
e
This unit complies with EC Directives 89/336/EEC
and 73/23/EEC.
e
The rating plate can be found inside the set after the
battery cover and battery are removed.
English ii
OUTLINE OF OPERATION
To help you get started enjoying using your camera right away, given below is
an outline of the fundamental operation, from setup to shooting to playback.
SETUP
(1) Connect the AC adapter/charger (page 128).
(2) Install the battery pack and SD Memory
Card*1 in the camera (page 35, 36).
CAUTION
e
e
This camera uses an SD Memory Card
instead of photographic film to record
images. Be sure to install the SD Memory
Card before operating the camera. A 128MB
SD Memory Card is supplied with this
camera.
Be sure to format the SD Memory Card with
this camera before using it. A card that is not
formatted using the camera may limit your
full use of all the camera’s capabilities.
SHOOTING
(1) Turn on the camera (page 37).
(2) Take photos in the BASIC operation mode*2.
e
In the BASIC mode, it's easy to take great photos
right away.
e
e
e
To switch the menu mode, see page 42.
For shooting video clips, see page 47.
For shooting still photos, see page 48.
1 English
PLAYBACK
(1) View your photos in the BASIC operation
mode (page 64).
Playback as well is easy in the BASIC mode.
*1: About the SD Memory Card
In this manual, the SD Memory Card is
referred to as “card”.
*2: Shooting in the BASIC mode
For recording and viewing images, your
camera has two modes to choose from. In the
BASIC mode, only the basic camera functions
are used. In the EXPERT mode, you have full
access to all the camera's functions.
Symbols used in this manual
HINT
Points that may prove useful when using the camera.
NOTE
Points giving some extended instructions or special points to pay
attention to.
CAUTION Points that require special attention.
(page xx) Refer to the page indicated for detailed information.
You may find the answers to questions or problems concerning camera
operation in the sections “COMMONLY ASKED QUESTIONS” (page 149) and
“TROUBLESHOOTING” (page 157).
English 2
CONTENTS
OUTLINE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
USING YOUR CAMERA SAFELY AND CORRECTLY . . . . . . . . .7
CHECKING THE INCLUDED ACCESSORIES . . . . . . . . . . . . . .25
GETTING THE MOST OUT OF YOUR CAMERA. . . . . . . . . . . .27
i PREPARATION
PARTS NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
CHARGING THE BATTERY PACK. . . . . . . . . . . . . . . . . . . . . . .34
INSTALLING THE BATTERY PACK AND CARD . . . . . . . . . . . .35
TURNING THE POWER ON AND OFF. . . . . . . . . . . . . . . . . . . .37
OPERATION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
SWITCHING THE MENU MODE. . . . . . . . . . . . . . . . . . . . . . . . .42
BEFORE TAKING PICTURES. . . . . . . . . . . . . . . . . . . . . . . . . . .44
3 English
BASIC MODE
i SHOOTING
CAPTURING IMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ABOUT THE BASIC MODE SHOOTING SETTING SCREEN . . 52
CHANGING THE SHOOTING SETTINGS . . . . . . . . . . . . . . . . . 55
OTHER SHOOTING FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . 58
i PLAYBACK
VIEWING IMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
ABOUT THE BASIC MODE PLAYBACK SETTING SCREEN . . 68
OTHER PLAYBACK FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . 70
English 4
EXPERT MODE
i SHOOTING
ABOUT THE EXPERT MODE SHOOTING SETTING SCREEN 78
VIDEO IMAGE QUALITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
FOCUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
FLICKER-REDUCTION FUNCTION . . . . . . . . . . . . . . . . . . . . . .83
ISO SENSITIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
WHITE BALANCE SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . .85
EXPOSURE CORRECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
i PLAYBACK
ABOUT THE EXPERT MODE PLAYBACK SETTING SCREEN.87
ROTATE IMAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
EDITING VIDEO CLIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
PRINT SETTINGS (STILL IMAGES ONLY) . . . . . . . . . . . . . . . .98
5 English
OPTION SETTINGS
i CAMERA SETTINGS
ABOUT THE OPTION SETTING SCREEN . . . . . . . . . . . . . . . 105
GUIDANCE FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
OPERATIONAL SOUNDS SETTING . . . . . . . . . . . . . . . . . . . . 108
USB FUNCTION SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
FILE NO. RESET FUNCTION. . . . . . . . . . . . . . . . . . . . . . . . . . 111
DATE AND TIME SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
SCREEN LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
TV SYSTEM SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
POWER SAVE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
RESETTING THE CAMERA SETTINGS . . . . . . . . . . . . . . . . . 121
FORMATTING A CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
CHECKING THE REMAINING CARD MEMORY . . . . . . . . . . . 124
CHECKING THE REMAINING BATTERY PACK CHARGE. . . 126
i OTHER DEVICES AND CONNECTIONS
DOCKING STATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
CABLE ADAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
CONNECTING TO A PRINTER . . . . . . . . . . . . . . . . . . . . . . . . 139
i APPENDICES
COMMONLY ASKED QUESTIONS . . . . . . . . . . . . . . . . . . . . . 149
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
English 6
USING YOUR CAMERA SAFELY AND
CORRECTLY
CAMERA
WARNING
i If the camera makes a strange noise, emits a
strange odor, or if smoke comes out from it,
immediately turn off the power and remove the
battery pack.
e
If the camera is used under these conditions, it may cause
a fire or electric shock. Immediately turn off the digital
camera, remove the battery pack, and wait to make sure
no more smoke comes from the camera. Then take it to the
dealer for service. Do not try to repair or open the camera
yourself.
i Do not modify or open the cabinet
e
High voltage circuits are inside, and there is a high risk of
fire or electric shock if they are touched. Any internal
check, setting, or repair should be performed by the dealer.
i Do not use while driving
e
e
Do not capture images, play back images, or watch the
LCD monitor while driving a vehicle. Doing so may cause
an accident.
Be careful where you put down the camera inside an
automobile. During sudden stops or turns it may fall behind
the brake pedal and prevent braking.
i Be aware of your surroundings when using the
camera
e
e
Pay close attention to your surroundings when using the
camera. Failure to do so may lead to an accident or injury.
When using the camera while walking, be very careful of
your surroundings and especially the traffic to avoid
accidents.
e
Do not use the camera inside an airplane or elsewhere
where its use may be restricted.
7 English
WARNING
i Do not get the camera wet
e
This camera is not water-resistant. Do not allow it to get
wet, as doing so may cause a fire or electric shock.
e
Do not use the camera in a bathroom.
e
If the camera gets wet, immediately turn it off and remove
the battery pack. Then take it to a dealer for repair. Using
the camera after it has been become wet may cause a fire,
electric shock, or other accident.
i Do not use during a storm
e
To avoid the risk of being struck by lightning, do not use the
camera during a thunderstorm. In particular, if used in an
open field, you have an increased chance of being struck by
lightning. Quickly seek refuge in a place that will protect you
from lightning.
i Do not place on an unstable surface
e
e
The camera may fall, resulting in damage to the camera or
injury.
If the camera has fallen and its body is damaged, turn it off,
remove the battery pack, and take it to the dealer for repair.
Using the camera after its body has been damaged may
cause a fire or electric shock.
i Do not look through the camera into the sun
e
Do not look through the camera at the sun or any other
strong source of light. Doing so may seriously injure your
eyes.
i Do not use the flash close to a person’s face
e
To prevent possible eye injury, do not use the flash near a
person’s face (especially young children or babies). If the
flash is used close to a person’s opened eyes, there is a risk
that it may damage that person’s eyesight.
English 8
USING YOUR CAMERA SAFELY AND CORRECTLY
WARNING
i Do not use where there is risk of explosion
e
Do not use the camera in a location where there is explosive
gas, or any other flammable material in the air. Doing so may
cause a fire or an explosion.
i Keep the camera out of the reach of children
e
The following may happen if children play with the camera:
d They may wrap the strap around their neck and suffo-
cate.
d They may swallow the battery pack or other small
parts. In such a case, consult a physician immedi-
ately.
d They may damage their eyesight if the flash goes off
too close to their eyes.
d They may get hurt by the camera.
CAUTION
i Cautions when carrying the camera
e
Do not walk around holding the camera by the handstrap. It
may hit other objects and get damaged. When walking
around, hold the camera in your hand or place it in a pocket.
e
e
Be careful not to drop the camera or subject it to strong
shocks.
Make sure direct sunlight does not hit the camera lens, as
that may damage the internal parts. When not using the
camera, be sure to always turn it off and close the lens cover.
i If the camera is not going to be used for a long
period of time
e
For safety’s sake, remove the battery pack from the camera.
This will prevent any possible excess heat or leakage of
battery fluid that may result in injuries or damage to nearby
objects. (Note that when the battery pack is removed for a
long period, the time and date settings will be cleared.)
9 English
CAUTION
i Cautions during use and storage
e
This camera is a precision instrument. When using or
storing the camera, make sure to avoid the following
locations to avoid damage.
d Places in direct sunlight
d Places where humidity and temperature are high
d Places that may get wet
d Places close to an air conditioner or heater
d Inside a car
d Places where there is dust and dirt
d Places where there is a fire burning
d Places where volatile products are stored
d Places subject to vibration
Operating environment:
d Temperature
d Humidity
0°C to 40°C (operation)
–20 to 60°C (storage)
30 to 90% (operation, no condensation)
10 to 90% (storage, no condensation)
English 10
USING YOUR CAMERA SAFELY AND CORRECTLY
DOCKING STATION AND AC ADAPTER/
CHARGER
DANGER
i Do not recharge battery packs that are not Li-ion
battery packs (Model DB-L20)
e
Do not recharge a battery pack other than the supplied Li-ion
battery pack (DB-L20). Recharging a dry-cell battery or other
type of rechargeable battery may cause excess heat,
combustion, or leakage, and cause a fire, injuries, burns, or
damage to nearby objects.
i Use a 100 to 240 V AC power supply
e
If used with a power supply other than the one specified, it
may cause a fire or electric shock. The power cord is rated
for 125 V AC. Therefore, if you plan to use the docking
station and/or the AC adapter/charger in a region with a
different voltage, it may be necessary to replace the power
cord with one that can be used in that location. For details,
please see page 168.
i Do not disassemble or modify
e
e
It is dangerous to touch the inside. Doing so may cause a fire
or electric shock.
Do not use as a direct current generator.
i Do not get the docking station or AC adapter/
charger wet
e
Make sure they do not get wet, as doing so may cause a fire
or electric shock.
e
Do not use the camera in a bathroom.
e
If the docking station or AC adapter/charger gets wet,
immediately unplug it from the power outlet and remove the
battery pack. Then contact the place of purchase. If used
while wet, it may cause a fire, electric shock, or an accident.
11 English
DANGER
i Cautions when plugging in
e
Securely plug the power cord all the way into the power
outlet. If the docking station or AC adapter/charger is used
with the power cord not fully plugged in, heat may be
generated and cause a fire.
e
e
e
Do not use if the power cord is damaged or cannot be
correctly plugged into the power outlet. Using in this
condition may cause a fire or electric shock.
Do not allow dust, etc., to build up on the power cord or
power outlet. A build-up of dust may cause a short circuit
or generate heat and cause a fire.
When unplugging the power cord, be sure to hold the plug
part and slowly pull it out of the power outlet. Pulling the
cord portion may damage the power cord and cause a fire
or electric shock.
i Do not pull on the power cord to unplug it
e
Do not leave the power cord plugged into the power outlet
while the other end is not plugged into the docking station
or AC adapter/charger. The loose end can cause
electrocution if touched with wet hands or if handled by
children.
e
e
Use only the supplied power cord. If a different power
cord is used, it may be rated for a different current load,
and that may cause a fire.
The supplied power cord is for exclusive use with the
devices supplied with your camera. Do not use it with
other devices, as doing so may cause a fire or electric
shock.
e
e
Do not use a bundled power cord, as the heat generated
may cause a fire.
When using an extension cord, make sure that the total
wattage of the connected devices does not exceed the
rated value of the extension cord. If the power load
exceeds the rated value, it may cause a fire.
English 12
DANGER
i Keep out of the reach of children
e
Children may place the battery pack or other small
components in their mouth or perform some other such
unforeseeable action. If swallowed, consult a physician
immediately.
i If smoke or a strange odor is emitted, or if
strange noises are heard, immediately unplug
the power cord from the power outlet
e
e
If used under these conditions, it make cause a fire or
electric shock.
If strange conditions such as these occur, immediately
unplug the device, remove the battery pack, and wait to
make sure no more smoke is emitted. Then contact the
place of purchase. Do not try to repair or open the device
yourself.
i Do not handle with wet hands
e
Handling the docking station or AC adapter/charger with
wet hands may cause an electric shock.
i Do not use during a storm
e
Do not touch the docking station, AC adapter/charger or
power cord while it is plugged into a power outlet during a
thunderstorm. Doing so may cause an electric shock.
13 English
CAUTION
i Do not damage the power cord
e
Do not place heavy objects on the power cord. Do not
place the power cord near a heat source. Do not
excessively bend the power cord, modify it, or secure it
with staples. Doing so may damage the power cord and
cause a fire or electric shock.
e
If the power cord is damaged, or if it does not plug
properly into the docking station, AC adapter/charger or
wall outlet, contact the place of purchase.
i Do not place on an unstable surface
e
e
The camera may fall, resulting in damage to the camera
or injury.
If it falls and the body is damaged, remove the battery
pack and contact the place of purchase. If used while
damaged, it may cause a fire, electric shock, or other
damage.
i Operating and storage conditions
e
Do not use close to a heat source (close to a stove or
heater) or leave it exposed to direct sunlight.
Operating environment:
d Temperature
d Humidity
0 to 40°C (charging)
–20 to 60°C (storage)
20 to 80%
(charging and storage)
English 14
LI-ION BATTERY PACK (DB-L20)
DANGER
This camera uses a Li-ion battery pack (Model DB-L20).
i If there is leaking, discoloration, change of
shape, rise in temperature, damaged exterior,
strange odor or any other abnormal condition,
immediately discontinue use and remove the
battery pack from the camera, taking care to
keep it well away from fire.
e
Continued use of the battery pack under any of these
conditions may result in fire, injury, explosion or other
serious damage.
e
If battery fluid is leaking, placing the battery pack in close
proximity to a fire or other heat source may ignite the
battery fluid and result in fire, damage, eruption of battery
fluid, or smoke fumes.
i Do not transform, take apart, or modify.
e
Safety mechanisms and protective devices have been in
incorporation in the battery pack for the purpose of
preventing danger. Any modification, by transforming,
disassembling, or directly soldering to it, etc., will defeat
these safety devices and possibly cause the battery pack
to catch fire, explode, or leak or spew battery fluid.
i Do not connect the (+) and (–) terminals with a
wire or other metal implement. Do not carry
loose or keep with necklaces, hairpins, etc.
e
Doing so may result in a short circuit, high voltage flow,
fire, explosion, leaking or spewing battery fluid, or heat
generation. Metal such as a wire or necklace, etc. may
cause heat to be generated.
i Do not throw the battery pack in the fire or sub-
ject it to heat
e
Doing so may cause the insulation to melt, damage the
gas discharge valve and safety mechanisms, or ignite
the battery fluid, resulting in fire or explosion.
15 English
DANGER
i Do not drop, hit, or submit the battery pack to
strong shocks
e
If the safety mechanisms and protective devices are
broken, an abnormal chemical reaction may occur inside
the battery pack, or cause the battery pack to catch fire,
explode, leak or spew battery fluid, or generate heat.
i Do not allow the battery pack to come into con-
tact with fresh or salt water, or allow the termi-
nals to become wet.
e
If the safety mechanisms and protective devices are
damaged by corrosion, an abnormal chemical reaction
may occur inside the battery pack, or cause the battery
pack to catch fire, explode, leak or spew battery fluid, or
generate heat.
i Operating and storage conditions
e
Temperature when using or recharging: 0 to 40°C
e
Do not use, recharge, store or leave the battery pack near fire or
inside a car exposed to the hot sun, etc. (locations in which the tem-
perature reaches 60°C or higher).
e
At high temperatures, the safety mechanisms and protective devices
inside the battery pack may be damaged by corrosion, causing an
abnormal chemical reaction to occur, or cause the battery pack to
catch fire, explode, leak or spew battery fluid, or generate heat. If the
safety mechanisms and protective devices are damaged, the battery
pack will become unusable. An environment with extremely high or
low temperatures will cause the battery capacity to deteriorate and
shorten the usable time, and may even shorten the battery life.
Avoid storing the battery pack with it near full charge. It is recom-
mended to store the battery pack when it is near fully discharged.
If the battery pack is completely discharged, it may become unable to
be recharged again. To avoid this, charge the battery pack for at
least five minutes every six months.
e
e
e
e
Storage temperature: –10°C to 30°C
When not using the battery pack, remove it from the camera and
store at 0°C to 30°C in a place with no condensation.
Humidity: 10% to 90% (no condensation)
English 16
DANGER
i Use only the supplied docking station and AC
adapter/charger
e
If another charger is used, the battery pack may be
overcharged, or recharged with an abnormal voltage,
causing an abnormal chemical reaction to occur, or cause
the battery pack to catch fire, explode, leak or spew battery
fluid, or generate heat.
i Use the battery pack only in the specified device
e
If the battery pack is used in a device other than that
specified, it may cause an abnormal voltage flow, or cause
the battery pack to catch fire, explode, leak or spew battery
fluid, or generate heat.
i Do not peel or damage the outer case
e
Damaging the outer case, inserting nails, hitting with a
hammer, stepping on the battery pack, etc. may cause a
short circuit inside the battery pack or cause the battery
pack to catch fire, explode, leak or spew battery fluid, or
generate heat.
i If the battery pack is leaking and the electrolyte
gets on your skin or clothing, immediately rinse
with clean water
e
If the electrolyte gets into your eyes, you risk losing your
eyesight. Immediately rinse your eyes with clean,
running water, and seek medical attention right away.
Any electrolyte that comes into contact with your skin or
clothing may harm your skin. Immediately rinse the area
with clean, running water.
i Insert the battery pack correctly, as specified
e
e
When installing the battery pack in the charger or
camera, pay attention to the indicated polarity (+ and –),
and insert it correctly.
If the battery pack is installed with the wrong orientation,
it may cause an abnormal chemical reaction while in the
charger, an abnormal voltage flow when it is used, or
cause the battery pack to catch fire, explode, leak or
spew battery fluid, or generate heat.
17 English
WARNING
i Always stop the recharging after the prescribed
recharge time, even if the battery pack is not
fully charged
e
If you continue to recharge the battery pack, it may cause
the battery pack to catch fire, explode, leak or spew
battery fluid, or generate heat.
i Keep out of the reach of children
e
They may handle the battery pack in an unforeseeable
manner that results in damage.
CAUTION
i Charge the battery pack before using it
e
Always recharge the battery pack before using it for the
first time, or when using it after it has been kept in storage
for a long time. During recharging, the battery pack may
be warm. This is normal and does not indicate a
malfunction.
i Note concerning the battery pack after use
e
The battery pack may be warm immediately after the
camera is used. If removing the battery pack, turn off
the camera and allow the battery pack to cool down
before removing it.
i Recycling the battery pack
e
To conserve the environment and for efficient use of
natural resources, please discharge the used battery
pack, cover the (+) and (–) terminals with tape and recycle
the insulated battery pack.
e
If disposing of the battery pack as unburnable trash,
please follow all applicable regulations of your area.
English 18
Concerning the accessories
WARNING
i Cautions concerning the use of the AC adapter/charger
e
e
Use only the supplied docking station and AC adapter/charger with your
camera. Do not use a docking station or AC adapter/charger other than the
ones indicated here, designed for specific use with your camera.
If a docking station or AC adapter/charger other than the ones specified is
used, it may damage the camera and cause a fire or electric shock.
i Cautions concerning the card
e
e
Immediately after use, the card will be very hot. Before removing the card,
turn off the camera and wait for the temperature to cool down.
Keep out of the reach of children. Young children may put the media in their
mouth and choke or cause some other unexpected injury or accident.
19 English
CONCERNING THE LITHIUM BATTERY
(CR2025)
WARNING
i Cautions concerning the CR2025 bat-
tery
e
A CR2025 lithium battery is used for the
remote control. Do not use a battery other
than the CR2025 lithium battery.
e
Install the battery with the (+) and (–)
terminals correctly oriented as indicated. If the
battery is placed in the wrong orientation, it
may cause a fire, overheating, or rupturing.
e
e
e
Do not recharge, short circuit, disassemble, modify, heat, or place the
battery in a fire. Doing so may cause a fire, overheating, or rupturing.
Do not hold the battery with metal tweezers or a similar tool. Doing so may
cause a short circuit leading to a fire, overheating, or rupturing.
Do not perform soldering on the battery or use, store, or leave it near a fire,
under direct sunlight, in a hot car, or other high temperature location.
e
Do not use the battery if it is leaking.
e
If the electrolyte gets into your eyes, you risk losing your eyesight. Do not
rub your eyes, wash them immediately with clean water, and seek medical
attention right away. If electrolyte gets on your skin or clothing, it may cause
irritation. Immediately wash with clean water.
e
Keep the battery out of the reach of children. If the battery is accidentally
swallowed, contact a physician immediately. It may cause poisoning or
suffocation.
e
e
When disposing of batteries, make sure to follow all applicable regulations.
When disposing of the lithium battery, place tape on its positive (+) and
negative (–) terminals to prevent shorting. Do not mix the lithium battery
with other batteries. Doing so may cause a fire or rupturing.
English 20
FOR CORRECT USE OF YOUR CAMERA
i Cautions before capturing important images
e
e
Before capturing important images, make sure that the camera is
operating properly and in condition to capture the image properly.
Sanyo Electric shall not be held responsible for any losses that result
from images that could not be recorded, are erased, destroyed, or
damaged in any way due to a problem with the camera, any of its
accessories, or its software.
i Caution concerning copyrights
e
The images you capture with your camera are for your own private use;
any other use may violate the rights of copyrights owners.
i Cautions when cleaning the camera
Cleaning procedure
1
2
Turn off the camera and remove the battery pack.
Remove the dirt with a soft cloth.
If the camera is extremely dirty,
3
Wipe with a soft cloth moistened with a mild detergent diluted with water
and wrung dry.
Caution
e
Do not use benzene or thinner products to clean the camera.
Doing so may cause deformation, discoloration, or paint peeling.
When using a chemically treated cloth, carefully read its instructions and
warnings.
e
Do not spray insecticides or volatile sprays on the camera. Do not let rubber
or vinyl objects contact the camera for a long period. They may cause
deformation, discoloration, or paint peeling.
21 English
i Caution concerning the battery pack
e
Periodically clean with a dry cloth the terminals (contacts) of the batteries.
Do not touch the battery terminals with your bare hands. Doing so will allow
contaminants from your hands to adhere to the terminals and oxidize,
increasing the contact resistance. If the contact resistance increases, the
usable life of the batteries will diminish.
i Caution when cleaning the lens
e
If the lens gets dirty, use a commercially available air blower or a cleaning
cloth for photographic equipment to clean it.
i When not using the camera for a long period
e
e
Remove the battery pack. However, when the battery pack is removed for a
long time, the camera functions may begin to not work properly. Periodically
reinstall the battery pack and check the camera functions.
If the battery pack is left in the camera, a small amount of power is still used
even if the camera is turned off. If the battery pack is left in the camera for a
long period, it may become completely discharged and lose its ability to be
recharged again.
i Cautions concerning condensation
e
Using the camera with condensation inside it may damage the camera.
If condensation seems likely to form
e
Place the camera in a plastic bag and seal it, and then wait until the camera
has reached the ambient temperature.
Be careful of condensation under the following conditions
e
When moving the camera suddenly from a cold place to a warm place.
e
When the ambient temperature changes drastically, such as when a heater
is turned on to quickly heat the room.
e
e
When the camera is placed in the path of cool air from an air conditioner.
When the camera is placed in a location of high humidity.
English 22
FOR CORRECT USE OF YOUR CAMER
(continued)
i Caution concerning undesired interference
e
The camera may create undesired interference if used close to a television
or radio. To avoid this type of interference, make sure the cores on the
supplied cables are not removed.
Dedicated USB interface cable
Dedicated AV interface cable
Core
Core
i Caution concerning magnetism
e
Do not place credit cards, bank cards, floppy disks, or other items that may
be damaged by magnetic fields near the speaker. Data may be lost or the
magnetic strips on cards may be damaged.
i Cautions concerning data storage
e
e
It is recommended that any important data be copied onto a separate media
(such as a hard disk, MO disk, or CD-R disk).
Stored data may be lost (or corrupted) in cases such as those listed below.
Sanyo Electric will not be held responsible for any damage or lost profits
arising from the loss of data.
d If the card is used incorrectly.
d If the card is not inserted correctly into the camera.
d If the card is subjected to electrical or mechanical shocks or other
forces.
d If the card is removed from the camera or if the camera is turned off
during reading or writing operations.
d If the card has reached the end of its usable life.
23 English
i Cautions when handling the cards
e
e
The cards are precision devices. Do not bend, drop, or subject them to
strong forces or shocks.
Avoid using or storing the cards in places with extremely high or low
temperatures, subject to direct sunlight, in a completely closed vehicle, near
air conditioners or heaters, or in humid or dusty locations.
e
e
e
Avoid using or storing the cards in locations where strong static electrical
charges or electrical noise can be easily generated.
Do not allow the edges of the cards to become contaminated with foreign
materials. Gently wipe away any contamination with a soft, dry cloth.
Do not carry the cards in trouser pockets, as the cards may become
damaged when you sit down or make other movements that may apply
forces.
e
e
Before using a new card or a card that was used in other equipment, be
sure to format it using the camera (see “FORMATTING A CARD” on page
122).
When buying commercially available products, carefully read the
instructions and warnings that come with the card.
i Caution concerning high temperatures
e
During shooting, when the internal temperature of the camera becomes
high, the \ icon will appear on the LCD monitor. When the \ icon
appears, it is still possible to capture and play back images for a while.
However, if the temperature rises further, it will become impossible to
record (although playback will still be possible). In this case, discontinue
shooting as soon as possible, and wait until the temperature falls before
using the camera again.
e
Note that particularly when shooting video clips, soon after the \ icon
appears, the remaining shooting time indication will appear, and when that
figure becomes 0, further shooting is impossible.
English 24
CHECKING THE INCLUDED ACCESSORIES
e
Handstrap: 1
e
Software: 2 CD-
ROM
e
Li-ion battery pack
(battery pack): 1
e
e
Docking station: 1
e
AV cable: 1
e
e
USB interface cable: 1
Cable adapter: 1
Remote control unit:e Lens cap: 1
1
A lithium battery
(CR2025) is installed
at the time of pur-
chase.
e
AC adapter/charger e Soft case: 1
and power cord: 1
25 English
e
SD Memory Card (128MB): 1
Contact end
Lock switch
Lock
Unlock
• Recording (images and sounds) and erasing
are inhibited (accidental erase protect
function) when the lock switch is set to the
LOCK position.
• The card is normally used with the lock
switch set to the unlocked position.
i Handstrap
i Lens cap
i Soft case
When not using the camera, keep
it in the soft case for protection.
Media cards that can be used with this camera
The type of card that can be inserted into and used with this camera is:
e SD Memory Card
English 26
GETTING THE MOST OUT OF YOUR CAMERA
Your digital movie camera can not only record video clips, you can also take
still photos and make audio recordings. For example, you can snap a still image
while shooting a video clip, or make just an audio recording. In addition, by
using the supplied docking station, it’s easy to hook up your camera to a TV or
computer.
Shooting video clips (page 47)
You expect your camera to record great quality still photos, but you can
record 640x480-pixel video clips as well. The maximum 30-frames-per-
second shooting speed guarantees beautiful, flowing movies for you to
enjoy. Another bonus is the capability to record small file sizes that are
perfect for uploading to Internet websites.
Capture still shots while recording a video clip
(page 49)
Suppose that while you’re recording a video clip, there’s a scene you’d like
to keep as a still photo. Your camera makes it possible to record the still
photo without interrupting the video clip recording.
27 English
Twin menus for easy operation (page 42)
The novice photographer will have no problem taking beautiful pictures,
thanks to the BASIC mode easy menu. All the settings necessary to cap-
ture the picture you want are easily and quickly set up. Of course, the
EXPERT mode menu is available for the experienced photographer, pro-
viding full control over detailed camera settings.
VIDEO CLIP MPEG4
640¶480 30fps HQ
VIDEO CLIP MPEG4
640¶480 30fps SHQ
<Example: BASIC Mode
Shooting Setting Screen>
<Example: EXPERT Mode
Shooting Setting Screen>
English 28
GETTING THE MOST OUT OF YOUR CAMERA
Movable monitor for any shooting angle
The movable LCD monitor lets you shoot from any angle. Hold the camera
high to get a great view of a parade, or swivel the monitor around to snap a
photo of yourself.
29 English
Docking station for easy connection
ThedockingstationsimplifiesthosecomplicatedconnectionstoyourTVor
computer. Just set the camera in the docking station, and you can view
your photos on your TV or computer right away. The remote control unit
makes it even more convenient.
Computer
TV
English 30
PREPARATION
PARTS NAMES
Front
Lens
Flash
Monitor unit
Stereo microphone
<To open the monitor unit>
Speaker
ON/OFF button
31 English
Rear
Multi-indicator
G Lit
Green: USB interface connection
(PC connection mode)
Red: USB interface connection
(PictBridge mode)
Charge the flush
Orange: AV cable connection
G Flashing
Green: Power save mode
Red (long interval): During self-timer
photography
Red (short interval): Accessing the card,
battery charge error
Main switch
Still image shooting button
Video clip recording button
Zoom switch
MENU button
Battery slot cover
Bottom
LCD monitor
SET button
Strap holder
Tripod stand hole Docking station terminal
Card cover
English 32
PARTS NAMES
Docking station
Front
Docking station terminal
CAMERA/CHARGE button
Charging indicator
Remote control sensor
Camera indicator
Rear
DIGITAL/AV terminal
DC IN terminal
Cable adapter
Docking station terminal
DIGITAL/AV terminal
DC IN terminal
33 English
CHARGING THE BATTERY PACK
The battery pack is not charged at the time of purchase and therefore needs to
be charged before use. In addition, if the battery charge becomes low while you
are using the camera, it is recommended to recharge it as soon as possible.
1
Connect the AC adapter/charger to
a power outlet.
e Use the supplied power cord for
connecting.
2
Insert the battery pack into the AC
adapter/charger.
e Set it in the battery slot.
e Be sure the battery pack is
correctly oriented when setting it in
the charger.
e Charging begins. During charging,
the charging indicator lights red.
e When the battery pack is
completely charged, the charging
indicator turns off.
e Charging will take approximately
90 minutes.
3
When the battery pack is fully
charged, remove it from the AC
adapter/charger.
e After removing the battery pack,
unplug the power cord from the
power outlet.
English 34
INSTALLING THE BATTERY PACK AND CARD
The card can be used after it has been formatted with the camera (page 122).
Make sure that the battery pack polarity (+ and –) and the card orientation are
correct.
Install the battery pack
1
Open the battery cover on the side.
e Open the battery cover by lightly
pressing it and sliding it towards
the rear.
2
Insert the battery pack.
e Firmly push it all the way in.
e Match the [I] mark on the battery
with the [I] mark on the camera.
<To remove the battery pack>
e Raise the battery pack and pull it
out.
35 English
3
Close the battery cover.
e Match the [I] marks, and slide the
cover towards the front to close it.
e At the time of purchase the battery
pack is not charged. Be sure to
install a fully charged battery pack
in the camera (page 34).
Install the card
1
Open the card cover on the bottom
of the camera.
2
Insert the card.
e Firmly insert the card until it clicks
into place.
e To remove the card, press it down,
and then release. The card will
protrude slightly, and you can then
pull it out.
3
Close the card cover.
CAUTION
e Do not attempt to forcefully remove the card.
English 36
TURNING THE POWER ON AND OFF
Turning on the camera
Main switch
1
Set the main switch.
To shoot pictures:
Set to [REC].
Monitor unit
To play back images:
Set the [PLAY].
2
3
Open the monitor unit.
Press the ON/OFF button for about
1 second.
e The camera turns on, and an
image appears on the LCD
monitor.
LCD monitor
ON/OFF button
37 English
Turning on the camera when the power save
(sleep) function is active
In order to preserve battery pack power, the power save (sleep) function will
automatically turn off the camera after one minute of no use during shooting, or
five minutes of no use during playback (factory-preset setting).
e When the power save function is active, you can restore the power by any of
the following methods:
Move the main switch.
Press the ON/OFF button.
Press the MENU button.
Press the SET button.
e After the power save function has been active for about 1 hour, the camera
will switch to the standby mode. In this case, you can restore the power by
pressing the ON/OFF button, or by closing and then opening the monitor
unit.
e When the AC adapter/charger is connected, the power save function will
become active about 10 minutes after the camera is turned on (factory-
preset setting).
e When the camera is connected to a computer or printer, it does not change
to the power save mode. In this case, the power save function becomes
active after about 12 hours.
e The user can specify the time elapsed before the power save function is
activated (page 119).
e When the camera is connected to a computer or printer, it does not change
to the power save mode. In this case, the power save function becomes
active after about 12 hours.
English 38
TURNING THE POWER ON AND OFF
Turning off the camera
1
Press the ON/OFF button for about
1 second.
e The camera turns off.
HINT
To immediately activate the power save function
e Press the ON/OFF button briefly to active the power save function.
About the standby mode
e To turn off the camera only briefly, you can close the monitor unit to put the
camera in the standby mode. The standby mode uses almost no power.
When the monitor unit is opened again, the camera turns on immediately
and you are ready to shoot or view images without any delay.
Note
If the } icon appears...
e When a picture is taken, the date and time it was captured is recorded with it.
When the date and time cannot be recorded with the image because the
date and time have not yet been set (page 114), the } icon appears. To
have the date and time recorded with images, please make this setting
before capturing images.
39 English
OPERATION BUTTONS
The procedures to change the camera settings, choose images, etc., are
performed by using the SET button to control the LCD monitor display. This
operation is used very frequently, so it is best to become familiar with it right
away.
1
2
Turn on the camera (page 37).
Press the MENU button.
e The Menu Screen appears.
<Select the icon above or below>
SET button
To select the icon above,
toggle the SET button up.
MENU button
VIDEO CLIP MPEG4
640¶480 30fps HQ
PHOTO RESOLUTION
2048¶1536 (3.2M)
To select the icon below,
toggle the SET button down.
SCENE SELECT
FULL AUTO
English 40
OPERATION BUTTONS
<Select the icon to the left or right>
To select the icon to the right, toggle
the SET button to the right.
VIDEO CLIP MPEG4
320¶240 30fps
To select the icon to the left, toggle
the SET button to the left.
VIDEO CLIP MPEG4
320¶240 30fps
<Actuate the selected icon>
Press the SET button. The selected
icon moves to the left end of the
lineup.
VIDEO CLIP MPEG4
320¶240 30fps
41 English
SWITCHING THE MENU MODE
Switch from the BASIC mode menu to the EXPERT mode menu, or vice versa,
depending on how you wish to use your camera.
1
2
Turn on the camera (page 37).
Press the MENU button.
e The Menu Screen (the Shooting
Setting Screen or the Playback
Setting Screen) appears.
VIDEO CLIP MPEG4
640¶480 30fps HQ
<Example: BASIC Mode
Shooting Setting Screen>
PLAYBACK METHOD
Set play all or 1
clip
<Example: BASIC Mode
Playback Setting Screen>
English 42
SWITCHING THE MENU MODE
3
Toggle the SET button to the left.
e The screen to select the menu
mode appears.
:
:
<Example: Shooting mode>
4
Toggle the SET button to the left
again.
e The menu mode switches from one
VIDEO CLIP MPEG4
640¶480 30fps SHQ
mode to the other.
<Example: EXPERT Mode
Shooting Setting Screen>
PLAYBACK METHOD
Set play all or 1
clip
<Example: EXPERT Mode
Playback Setting Screen>
43 English
BEFORE TAKING PICTURES
For best results
Hold the camera securely, keeping your elbow close to your body and
making sure the camera is stable.
Correct hold
Incorrect hold
A finger is blocking
the lens or flash.
Make sure that the lens and flash are not blocked by your fingers or the
handstrap.
HINT
e Images captured in the still image shooting mode can be rotated when they
are played back (page 89). Note that video clips cannot be rotated while they
are being played back.
e When the still image shooting button is pressed halfway, the image in the
LCD monitor may waver vertically. This is the result of internal image
processing and is not a malfunction. This wavering is not recorded and will
not affect your images in any way.
e When the optical zoom is used or when the autofocus is operating, the image
may appear to waver, but this is not a malfunction.
English 44
BEFORE TAKING PICTURES
Using the autofocus
The autofocus will work in almost all situations; however, there are
certain conditions that may cause the autofocus function to not work
properly. If the autofocus function is not working properly, set the focus
range to capture images (page 82).
i Conditions that may cause incorrect focus
The following examples are some of the situations where the autofocus
function may not work.
e Subjects with low contrast, very
bright subjects at the center of
the image or dark subjects or
locations
Use the focus-lock function to lock
the focus on an object with contrast
at the same distance as the
desired subject.
e Subjects without vertical lines
Use the focus-lock function to lock
the focus on the subject while
holding the camera vertically.
The following examples are some of the situations where the autofocus
function may work, but not as desired.
e When both near and far objects
are present
Use the focus-lock function to lock
the focus on an object at the same
distance as the desired subject,
then reposition the camera to
compose the picture.
45 English
e Fast-moving subjects
Use the focus-lock function to lock
the focus on an object at the same
distance as the desired subject,
then reposition the camera to
compose the picture.
Hints for taking pictures
Muting the operation sounds
e The operation sounds that are generated, for example, when the still image
shooting button, MENU button or SET button is pressed, as well as the audio
guidance when you switch the mode, can be muted (page 108).
Where is the image and audio data saved?
e All the image and sound data is recorded on the card installed in the camera.
Taking pictures in backlight conditions...
e When taking pictures with the light coming from behind the subject, due to
the characteristics of the lens, light lines or ghost patterns (flare
phenomenon) may appear in the captured image. In this situation, it is
recommended that you avoid taking pictures with the subject lit from behind.
While the image data is being recorded...
e The multi-indicator will light red while the image is being written to the
memory. Another image can be captured only after the red light turns off.
However, even when the multi-indicator is lit red, depending on the camera’s
internal memory remaining capacity, in some cases the next image can be
captured about 2 seconds after shooting.
English 46
BASIC MODE
SHOOTING
CAPTURING IMAGES
Recording video clips
1
2
3
Turn on the camera (page 37).
Set the main switch to REC.
Main switch
Press the video clip recording
button [l] to start recording.
e Recording begins. During shooting,
X appears in the LCD monitor.
e It is not necessary to continue
pressing the video clip recording
button while shooting.
Video clip recording button
00:00:15
4
End the recording.
e Press the video clip recording
button again to stop recording.
Note
Focus lock during video clip recording
e The autofocus can be set to a fixed focus during video clip recording if you
toggle the SET button up. When the autofocus is fixed, the p icon appears
on the LCD monitor.
47 English
Capturing still images
1
2
3
Turn on the camera (page 37).
Main switch
Set the main switch to REC.
Press the still image shooting
button [S] to capture the image.
1 Press the still image shooting
button halfway.
e The autofocus operates, and the
image is focused (focus lock).
Still image shooting button
2 Continue to gently press the still
image shooting button all the
way.
e The shutter releases and the image
e You can view the captured image
on the LCD monitor by keeping the
still image shooting button
depressed when you capture the
image.
is captured.
Target mark
English 48
CAPTURING IMAGES
Shoot a still image while recording a video clip
You can capture a still image while you are recording a video clip.
Main switch
1
Turn on the camera (page 37).
Set the main switch to REC.
2
3
Press the video clip recording
button [l] to begin recording.
Still image shooting
button
Video clip recording
button
4
5
When you see a scene you'd like to
capture as a still image, press the
still image shooting button [S].
01:25
End the recording.
e Press the video clip recording
button to stop recording.
49 English
Note
About the target mark
e The target mark indicates the position which is currently focused. If the target
mark does not appear, or if it appears at a position that is different from the
point you wish to focus, you can refocus, for example, by changing the
shooting angle.
e The large target mark appears when the camera focuses on a wide area in
the center of the screen.
HINT
Shoot a still image while recording a video clip
e If you press the still image shooting button while recording a video clip, the
frame is also saved as a still image. Note, however, that in this case the flash
will not operate.
e If the still image resolution is set to a setting other than [, and you press
the still image shooting button while recording a video clip, the displayed
image stops briefly and then returns to video clip recording after the still
image is captured.
Note
e The data for a video clip is very large. Therefore, be aware that if the video
clip is uploaded to a computer to be played back, the computer may not be
able to play back the video fast enough, making it appear jerky. (The video
will always be displayed properly on the LCD monitor or a television.)
e Depending on the card, shooting may end even before the possible shooting
time indicated on page 167.
English 50
CAPTURING IMAGES
AUDIO RECORDING
You can make audio recordings with your camera.
1
2
Select the audio recording icon <
from the recording mode menu,
and press the SET button.
e The camera changes to the audio
recording mode.
Press the video clip recording
00:00:16
button [l].
e Recording begins.
e To end the recording. press the
video clip recording button again.
<Screen during audio
recording>
51 English
ABOUT THE BASIC MODE SHOOTING SETTING
SCREEN
For shooting in the BASIC mode, you can change the video clip image quality
and still image resolution settings, as well as modify the shooting settings for
various functions. These settings are performed on the BASIC Mode Shooting
Setting Screen.
Display the BASIC Mode Shooting Setting
Screen
1
2
Turn on the camera (page 37).
Main switch
Set the main switch to REC.
3
4
Press the MENU button.
e The Menu Screen appears.
MENU button
Set the camera to the BASIC mode
(page 42)
e The BASIC Mode Shooting Setting
e To cancel the BASIC Mode
Shooting Setting Screen, press the
MENU button.
Screen appears.
VIDEO CLIP MPEG4
640¶480 30fps HQ
English 52
ABOUT THE BASIC MODE SHOOTING SETTING SCREEN
BASIC Mode Shooting Setting Screen
8
VIDEO CLIP MPEG4
9
640¶480 30fps HQ
F
.................
1
............................ 2
...........
3
............
4
.............................
5
.............................
6
.........................................
7
53 English
1 Video clip menu (page 55)
5 Flash menu (page 60)
8: Record at 640 x 480 pixels,
30 frames per second
9: 320 x 240 pixels, 30 frames
per second
k: Automatic flash mode
m: Forced flash mode
l: Flash off mode
6 Self-timer menu (page 62)
<: 320 x 240 pixels, 15 frames
=: 176 x 144 pixels, 15 frames
per second
N: Self-timer off
per second
y: Self-timer on (2 seconds)
x: Self-timer on (10 seconds)
7 Option icon (page 105)
<: Make an audio recording
2 Photo resolution menu (page
56)
Displays the Option Setting
Screen.
8 Menu mode display (page 42)
9 Help display (page 107)
F Remaining battery power (page
126)
Y: 2048 x 1536-pixel resolution
icon (3,200,000 pixels)
Z: 1600 x 1200-pixel resolution
icon (2,000,000 pixels)
[: 640 x 480-pixel resolution
icon (300,000 pixels)
3 Scene select menu (page 58)
=: Full auto icon
a: Sports icon
>: Portrait icon
+: Landscape icon
/: Night view icon
Q: Lamp icon
4 Filter menu (page 59)
&: No filter
%: Cosmetic filter on
5: Slim filter on
W: Monochrome filter on
3: Sepia filter on
(: Ghost filter on
e When you specify multiple functions that cannot be simultaneously
enabled, the function which was last set becomes the active setting, and
the other settings accordingly change automatically.
English 54
CHANGING THE SHOOTING SETTINGS
In the BASIC mode, you can change the monitor brightness, the video clip
image quality and the still image resolution settings.
Video clip image quality setting
When it comes to video clips, a larger number of pixels and a higher the
frame rate means better image quality and smoother playback. On the
other hand, the file size becomes large and uses more memory. Set the
image quality to a setting that’s right for your purpose, whether for home
viewing on a TV or for showing on the Internet, for example.
1
Display the BASIC Mode Shooting
Setting Screen (page 52), and
select the video clip menu.
VIDEO CLIP MPEG4
640¶480 30fps HQ
8 : Record at 640 x 480 pixels, 30
frames per second
9 : Record at 320 x 240 pixels, 30
frames per second
< : Record at 320 x 240 pixels, 15
frames per second
= : Record at 176 x 144 pixels, 15
frames per second
< : Make an audio recording
2
Select the desired icon from the
video clip menu, and press the SET
button.
e This completes the video clip
image quality setting.
55 English
Still image resolution setting
By setting the still image resolution (pixels) to a higher setting, image
detail is enhanced for a smoother, finer picture. However, the file size
also becomes large and uses more memory. Select the resolution setting
that suits your purpose.
1
Display the BASIC Mode Shooting
Setting Screen (page 52), and
select the photo resolution menu.
PHOTO RESOLUTION
2048¶1536 (3.2M)
Y : 2048 x 1536-pixel resolution
(3.2M)
Z : 1600 x 1200-pixel resolution
(2M)
[ : 640 x 480-pixel resolution
(0.3M)
The numbers in parentheses ( ) refer
to the approximate number of pixels in
the image (units: megapixels).
2
Select the desired icon from the
photo resolution menu, and press
the SET button.
e This completes the still image
resolution setting.
English 56
CHANGING THE SHOOTING SETTINGS
Adjusting the brightness of the LCD monitor
(when shooting)
The brightness of the LCD monitor during shooting can be adjusted.
Adjust the brightness when it is difficult to see the LCD monitor image
due to ambient lighting. In addition, in very bright surroundings, such as
outdoors on a sunny day, you can turn the backlight OFF to preserve
battery power.
LCD BRIGHTNESS
1
With the Shooting Setting Screen
not shown, toggle the SET button
down for at least 1 second.
LCD BACKLIGHT
e The Monitor Brightness Screen
ON
appears.
OFF
e You can also access the Monitor
Brightness Screen from the
Shooting Screen by pressing and
holding the SET button
downwards.
ADJUST
0
2
Toggle the SET button to the left or
right to adjust the brightness, and
press the SET button.
e This completes the LCD monitor
brightness setting, and you are
returned to the Shooting Screen.
57 English
OTHER SHOOTING FUNCTIONS
Scene Select feature
You can select from various preset settings (aperture, shutter speed, etc.)
for specific shooting conditions.
1
Display the BASIC Mode Shooting
Setting Screen (page 52), and
select the scene select menu.
= : The camera makes settings
suitable for the surrounding
conditions.
SCENE SELECT
FULL AUTO
a : Capture a split-second image of
a fast-moving subject.
> : Enhance the 3D feeling of the
subject by blurring the
background.
+ : For beautiful shots of distant
scenery.
/ : Photograph the subject while
keeping the background night
scenery.
Q : Increase the sensitivity when
taking pictures.
2
3
Select the desired icon from the scene select menu, and press the
SET button.
e This completes the scene select function setting.
Take the picture.
For video clip recording, see page 47.
For still image shooting, see page 48.
To return to normal photography, select = from the scene select menu,
and press the SET button.
English 58
OTHER SHOOTING FUNCTIONS
Note
e When capturing images using the lamp Q or night view / setting, use a
tripod or other method to stabilize the camera.
Filter feature
The filter feature changes the aperture and shutter speed settings, as well
as the color tones, to apply unique effects to the photographed image.
1
Display the BASIC Mode Shooting
Setting Screen (page 52), and
select the filter menu.
FILTER
NO
& : No filter
% : Skin tones are enhanced in
close-up shots (cosmetic filter).
5 : Change the vertical-horizontal
proportions of the subject (slim
filter).
W : Snap black-and-white photos
(monochrome filter).
3 : Create a sepia-tone photo (sepia filter).
( : A radiant effect is added to the subject (ghost filter).
2
3
Select the desired icon from the filter menu, and press the SET
button.
e This completes the filter setting.
Take the picture.
For video clip recording, see page 47.
For still image shooting, see page 48.
e To return to normal photography, select & from the filter menu, and
press the SET button.
59 English
Using the flash
The flash is used not only for taking pictures where there is insufficient
light, but also when the subject is in shade or in backlight conditions.
Your camera has three modes of operation (automatic flash mode, forced
flash mode, and flash off mode). The flash is available only when
shooting still images.
1
Display the BASIC Mode Shooting
Setting Screen (page 52), and
select the flash menu.
FLASH
AUTO
k : The camera will detect the
subject brightness and use the
flash only when required. In a
backlight situation, if only the
center of the image is very dark,
the flash will operate to
compensate (auto flash).
m : The flash will operate with every
image captured regardless of
the conditions. Use this setting
under backlight conditions,
when the subject is in shade,
under fluorescent lighting
conditions, etc. (forced flash).
l : The flash will not operate even in dark situations. Use this setting
when capturing an image in a location where flash photography is
prohibited, or when shooting a night landscape scene (flash off).
2
Select the desired icon from the flash menu, and press the SET
button.
e This completes the flash setting.
English 60
OTHER SHOOTING FUNCTIONS
3
Take the picture.
For video clip recording, see page 47.
For still image shooting, see page 48.
e To return to normal photography, select k from the flash menu, and
press the SET button.
Using the zoom
Your camera has two zoom functions: optical zoom and digital zoom.
Zoom switch
1
2
Point the camera lens at the
subject.
Press [T] or [W] on the zoom switch
to compose the desired image.
[T]: Zoom in on the subject.
[W]: Zoom out.
e When the zoom switch is pressed,
the zoom bar appears on the LCD
monitor.
LCD monitor
Zoom bar
Pointer
e When the optical zoom factor is at
maximum, zooming stops
When both optical
and digital zoom
are enabled
temporarily. When [T] on the zoom
switch is pressed again, the mode
changes to the digital zoom mode
and zooming continues (if digital
zooming is enabled).
Optical zoom
Digital zoom (Yellow)
When optical zoom
only is enabled
3
Take the picture.
For video clip recording, see page 47.
For still image shooting, see page 48.
61 English
Self-timer photography
1
Display the BASIC Mode Shooting
Setting Screen (page 52), and
select the self-timer menu.
SELF-TIMER
OFF
N : Turns off the self-timer function.
y : Turns on the self-timer function.
The image is captured about 2
seconds after the video clip
recording button or still image
shooting button is pressed.
x : Turns on the self-timer function.
The image is captured about 10
seconds after the video clip
recording button or still image
shooting button is pressed.
2
3
Select the desired icon from the
self-timer menu, and press the SET
button.
This completes the self-timer setting.
Take the picture.
For video clip recording, see page 47.
For still image shooting, see page 48.
English 62
OTHER SHOOTING FUNCTIONS
HINT
To pause or cancel the self-timer function...
e If the video clip recording button or still image shooting button is pressed
again before the image is captured, the self-timer countdown temporarily
stops. Press the video clip recording button or still image shooting button one
more time to restart the self-timer.
e To cancel self-timer photography, select the N icon from the self-timer
menu, and press the SET button.
When x is selected...
e When the video clip recording button or
still image shooting button is pressed,
the illumination light and the multi-
indicator will blink for about 10
seconds, and then the image is
captured. Also, 4 seconds before the
shutter releases, the indication below
appears on the LCD monitor.
e If you swivel the monitor unit towards,
the self-timer indication will be visible to
the subject.
63 English
PLAYBACK
VIEWING IMAGES
Main switch
1
Turn on the camera (page 37), and
set the main switch to PLAY.
e If the main switch is set to PLAY
after a video clip was recorded, the
last recorded video clip is
displayed.
e If the main switch is set to PLAY
after a still image was captured, the
last recorded still image is
displayed.
SET button
2
3
Select the image you wish to view.
To display the previous image, toggle
the SET button to the left.
To display the next image, toggle the
SET button to the right.
JOG
<Example: After video clip
recording>
Play back a video clip.
Follow these steps to play back a
video clip.
Normal playback
e Press the SET button.
Pause
e While the video clip is playing,
toggle the SET button up. To
resume playback, press the SET
button.
<Example: After still image
shooting>
English 64
VIEWING IMAGES
To play back one image at a time (single-frame step)
e During forward playback
After pausing playback, toggle the SET button to the right.
For slow playback, press and hold the SET button to the right.
e During reverse playback
After pausing playback, toggle the SET button to the left.
For slow reverse playback, press and hold the SET button to the left.
To accelerate playback
e 15x fast forward playback
During normal playback, toggle the SET button to the right.
e 30x fast forward playback
During 15x playback, toggle the SET button to the right.
d
During fast forward playback, the audio is not heard.
If you toggle the SET button to the left, the images are played back in
reverse (the audio is not played back).
d
e Return to normal playback speed
Press the SET button.
JOG playback
JOG playback lets you display the previous frame or next frame, as well
as search for a particular frame during playback.
1
In the video clip playback stop or
pause mode, toggle the SET button
up.
e The JOG Playback Screen
appears.
Fast forward:
Toggle the SET button to the right.
Rewind:
Toggle the SET button to the left.
Playback:
Press the SET button.
Position of currently displayed
frame
2
Toggle the SET button down.
e You are returned to the Playback
Screen.
65 English
Convenient 9-image display playback
1
Turn on the camera (page 37), and
set the main switch to PLAY.
e If the main switch is set to PLAY
after a video clip was recorded, the
last recorded video clip is
displayed.
e If the main switch is set to PLAY
after a still image was captured, the
last recorded still image is
displayed.
Zoom switch
Main switch
2
3
Press [W] (P) on the zoom
switch.
e The 9-image display appears.
Select the image to play back.
e Toggle the SET button up, down,
left or right to move the orange
frame to the desired image, and
press the SET button.
SET button
Video clip
Orange frame
Still image
Instead of pressing the SET button,
you can press [T] ([]]) on the
zoom switch to show the image full
screen.
100
0001
0002
0005
0008
0003
0006
0009
0004
0007
Audio data
Image number
Folder number
Note
e The 9-image multi-playback display can also be accessed by selecting P
on the BASIC Mode Playback Setting Screen.
English 66
VIEWING IMAGES
Audio data playback
A { mark indicates an image for
which audio data was also recorded.
Playback
Press the SET button.
Pause
During playback, toggle the SET
button up.
Stop playback
During playback, toggle the SET
button down.
Magnifying (zooming in) the image
Magnification indication
1
Display the image that you want to
magnify.
ZOOM
117%
e For a video clip, pause playback at
the place you want to magnify.
2
Press [T] ([]]) on the zoom
e Magnification is enabled.
e The image is magnified, and the
central portion of image is
displayed.
ZOOM I/O
MOVE
switch.
SHUTTER FOR SAVE
e Toggle the SET button to view different parts of the magnified image.
To magnify:
Press [T] ([]]) on the zoom switch.
To return to normal size:
Press [W] ([P]) on the zoom switch.
HINT
The magnified portion of the image can be saved as a separate image.
e Press the still image shooting button. The magnified portion is saved as a
new still image.
67 English
ABOUT THE BASIC MODE PLAYBACK SETTING
SCREEN
The BASIC mode playback settings are performed on the BASIC Mode
Playback Setting Screen.
Display the BASIC Mode Playback Setting
Screen
Main switch
1
2
3
Turn on the camera (page 37).
Set the main switch to PLAY.
Press the MENU button.
e The Menu Screen appears.
MENU button
4
Set the camera to the BASIC mode
(page 42)
PLAYBACK METHOD
e The BASIC Mode Playback Setting
Set play all or 1
clip
Screen appears.
e To cancel the BASIC Mode
Playback Setting Screen, press the
MENU button.
English 68
ABOUT THE BASIC MODE PLAYBACK SETTING SCREEN
BASIC Mode Playback Setting Screen
8
1
2
PLAYBACK METHOD
3
4
5
6
Set play all or 1
clip
9
7
F
1 Playback method setting (page 70)
e Select continuous playback or single-frame playback.
2 Multi-playback (page 66)
e Display images in the 9-frame multi-display format.
3 Volume control (page 71)
e Adjust the playback volume for video clips and audio data.
4 Monitor brightness (page 72)
e Adjust the brightness of the LCD monitor backlight.
5 Data protect setting (page 73)
e Protect data from accidental erasure.
6 Erase (page 75)
e Delete images from the card memory.
7 Option icon (page 105)
e Displays the Option Setting Screen.
8 Menu mode display (page 42)
9 Help display (page 107)
F Remaining battery power (page 126)
69 English
OTHER PLAYBACK FUNCTIONS
Playback mode
Images can be viewed continuously (slideshow playback) or you can
choose to show single images.
1
2
Display the BASIC Mode Playback
Setting Screen (page 68).
PLAYBACK METHOD
DURATION OF PHOTO
Select the playback method icon
4, and press the SET button.
e The Playback Mode Screen
PLAY ALL
1 CLIP
1SEC
appears.
1 CLIP:
Display only the selected image.
PLAY ALL:
Play back images in slideshow
fashion.
PLAYBACK METHOD
3
Select the desired playback mode,
and press the SET button.
DURATION OF PHOTO
<PLAY ALL>
PLAY ALL
1SEC
e The screen to set the time that
each image is displayed appears.
1 Toggle the SET button up or down
to specify the time that each image
is shown.
2 Press the SET button.
e The display time is set, and you are
returned to the BASIC Mode
Playback Setting Screen.
<1 CLIP>
e The camera is set to display only
the image you select, and you are
returned to the BASIC Mode
Playback Setting Screen.
English 70
OTHER PLAYBACK FUNCTIONS
Volume control
Adjust the volume of video clip and audio data playback.
1
2
Display the BASIC Mode Playback
Setting Screen (page 68).
VOLUME
Select the volume icon Z, and
press the SET button.
e The volume control bar appears.
VOLUME SETTING
3
Toggle the SET button left or right
to set to the desired volume, and
press the SET button.
1
71 English
Monitor brightness (playback)
Adjust the brightness of the camera’s LCD monitor display during
playback. Use this adjustment when the monitor image is difficult to view
because of ambient lighting.
In addition, in very bright surroundings, such as outdoors on a sunny
day, you can turn the backlight OFF to preserve battery power.
1
2
Display the BASIC Mode Playback
Setting Screen (page 68).
LCD BRIGHTNESS
Select the LCD brightness icon
r, and press the SET button.
e The brightness control bar
e You can also access the Monitor
Brightness Screen from the
Shooting Screen by pressing and
holding the SET button
downwards.
LCD BACKLIGHT
appears.
ON
OFF
ADJUST
0
3
Toggle the SET button left or right
to adjust the LCD monitor
brightness, and press the SET
button.
e The brightness is set, and you are
returned to the BASIC Mode
Playback Setting Screen.
English 72
OTHER PLAYBACK FUNCTIONS
Image protect mode
(prevent accidental erasure)
1
2
Display the data that you want to
protect from accidental erasure,
and display the BASIC Mode
Playback Setting Screen (page 68).
PROTECT
Select the protect icon A, and
press the SET button.
e “LOCK?” appears.
LOCK?
e If the protect mode has already
been enabled for the data, then
“UNLOCK?” appears.
YES
EXIT
PROTECT
3
Toggle the SET button up or down
to select “YES”, and press the SET
button.
UNLOCK?
e The protect mode is set for the
e The protect mark B indicates
that the data is locked.
data.
YES
EXIT
e To return to the BASIC Mode
Playback Setting Screen, press the
MENU button.
73 English
CAUTION
e Even if the protect mode is set for certain data files, they will be erased if the
card is reformatted.
HINT
To select a different image in steps 2 and 3...
e Toggle the SET button to the left or right.
To cancel the protect mode for an image...
e Display the desired data and repeat steps 1 to 3. The protect mark B will
disappear and the protect mode is canceled.
English 74
OTHER PLAYBACK FUNCTIONS
Erasing data
You can erase data that is stored on the card if you no longer need it. You
can erase the data one at a time, or all at once.
1
2
Display the BASIC Mode Playback
Setting Screen (page 68).
ERASE
Select the erase icon c, and
press the SET button.
ONE ERASE
ERASE ALL
EXIT
e The Erase Mode Screen appears.
ONE ERASE:
Erases one data at a time.
ERASE ALL:
Erases all the data from the card.
EXIT:
Returns to the BASIC Mode
Playback Setting Screen.
3
Toggle the SET button up or down to select the erase mode, and
press the SET button.
e The Erase Confirmation Screen appears.
<ONE ERASE>
e Toggle the SET button to the left or right to select the data you wish to
erase.
<ERASE ALL>
e Toggle the SET button to the left or right confirm the data to erase.
75 English
4
Toggle the SET button up or down to select “YES”, and press the
SET button.
<ONE ERASE>
e The currently displayed image is deleted.
e To erase other data, select the data, and press the SET button.
e To return to the BASIC Mode Playback Setting Screen, press the
MENU button.
<ERASE ALL>
e The Erase Confirmation Screen again appears. To erase the data,
select “YES”, and press the SET button. When data erase is
completed, “NO IMAGE” is shown.
CAUTION
e Data which is protected from accidental erase cannot be erased. To erase
protected data, set the protect setting for the data to off (page 73), and then
follow the data erase procedure.
English 76
OTHER PLAYBACK FUNCTIONS
Displaying image data (Information Screen)
On the Information Screen you can check what the settings were when an
image was captured.
1
2
Display the desired image.
INFO
100-0002
328KB
3
4
Press the MENU button for at about
2 seconds.
e The Playback Information Screen
1
2
640¶480
MPEG4
5
6
appears.
00:00:06
UNUSED MEMORY 78%
e If the MENU button is pressed
again, the Playback Information
Screen is exited.
7
2003.12.25 19:30
8
1 Video clip mode settings
2 Remaining card memory
3 Image or sound number
4 Protect setting
<Video clip playback mode>
INFO
100-0001
3
4
5 File size
9
2
2048×1536
986KB
5
7
6 Shooting or recording time
7 Remaining battery charge
8 Date and time of image
9 Photo resolution setting
UNUSED MEMORY 78%
2003.12.25 19:30
8
<Still image playback mode>
INFO
100-0004
3
4
96KB
5
6
2
AAC
00:00:03
UNUSED MEMORY 21%
7
2003.12.25 19:30
8
<Audio data playback mode>
77 English
EXPERT MODE
SHOOTING
ABOUT THE EXPERT MODE SHOOTING
SETTING SCREEN
Compared to the BASIC mode, the EXPERT mode allows you much more
control over the various shooting settings. These settings are performed on the
EXPERT Mode Shooting Setting Screen.
Display the EXPERT Mode Shooting Setting
Screen
Main switch
1
2
3
Turn on the camera (page 37).
Set the main switch to REC.
Press the MENU button.
e The Menu Screen appears.
MENU button
4
Set the camera to the EXPERT
mode (page 42)
e The EXPERT Mode Shooting
e To cancel the EXPERT Mode
Shooting Setting Screen, press the
MENU button.
Setting Screen appears.
VIDEO CLIP MPEG4
640¶480 30fps SHQ
English 78
ABOUT THE EXPERT MODE SHOOTING SETTING SCREEN
EXPERT Mode Shooting Setting Screen
H
VIDEO CLIP MPEG4
I
640¶480 30fps SHQ
J
..............................
1
..............................
..............................
..............................
..............................
..............................
..............................
...................................
..............................
..............................
.........................................
2
3
4
5
6
7
8
9
F
G
79 English
1 Video clip menu (page 81)
6 Self-timer menu (page 62)
:: 640 x 480 pixels, 30 frames
per second, low compression
8: 640 x 480 pixels, 30 frames
per second
N: Self-timer off
y: Self-timer on (2 seconds)
x: Self-timer on (10 seconds)
7 Focus menu (Page 82)
9: 320 x 240 pixels, 30 frames
<: 320 x 240 pixels, 15 frames
per second
-: Wide end: 10 cm to infinity
Tele end: 80 cm to infinity
*: 80 cm to infinity
+: 2 cm to 60 cm
per second
=: 176 x 144 pixels, 15 frames
8 Flicker-reduction menu (page
83)
per second
2 Photo resolution menu (page
56)
p: Flicker-reduction function off
icon.
Y: 2048 x 1536-pixel resolution
o: Flicker-reduction function on
icon.
icon (3,200,000 pixels)
Z: 1600 x 1200-pixel resolution
icon (2,000,000 pixels)
9 ISO sensitivity menu (Page 84)
t: Auto sensitivity (ISO50 to
200)
[: 640 x 480-pixel resolution
icon (300,000 pixels)
*: ISO50 icon.
3 Scene select menu (page 58)
=: Full auto icon
a: Sports icon
u: ISO100 icon.
v: ISO200 icon.
w: ISO400 icon.
F White balance menu (page 85)
>: Portrait icon
+: Landscape icon
/: Night view icon
Q: Lamp icon
>: Auto white balance icon.
r: Sunny icon.
o: Cloudy icon.
p: Fluorescent lighting icon.
q: White (incandescent) light
icon.
G Option icon (page 105)
e Displays the Option Setting
Screen.
H Menu mode display (page 42)
I Help display (page 107)
J Remaining battery power (page
126)
4 Filter menu (page 59)
&: No filter
%: Cosmetic filter on
5: Slim filter on
W: Monochrome filter on
3: Sepia filter on
(: Ghost filter on
5 Flash menu (page 60)
k: Automatic flash mode
m: Forced flash mode
l: Flash off mode
e When you specify multiple functions that cannot be simultaneously
enabled, the function which was last set becomes the active setting, and
the other settings accordingly change automatically.
English 80
VIDEO IMAGE QUALITY
For high image quality and smooth video clip playback, a larger number of
pixels and high frame rate is selected. A lower compression rate setting
produces even more beautiful images. However, the file size becomes large
and uses more memory, set the image quality to a setting that’s right for your
purpose.
1
Display the EXPERT Mode
Shooting Setting Screen (page 78),
and select the video clip menu.
VIDEO CLIP MPEG4
640¶480 30fps SHQ
: : Record at 640 x 480 pixels, 30
frames per second, low
compression
8 : Record at 640 x 480 pixels, 30
frames per second
9 : Record at 320 x 240 pixels, 30
frames per second
< : Record at 320 x 240 pixels, 15
frames per second
= : Record at 176 x 144 pixels, 15
frames per second
2
Select the desired icon from the
video clip menu, and press the SET
button.
e This completes the video clip
image quality setting.
81 English
FOCUS
1
Display the EXPERT Mode
Shooting Setting Screen (page 78),
and select the focus menu.
FOCUS
TOTAL RANGE
e When shooting a subject at a
medium to far distance, by setting
the focus range to *, you will find
it both easier and faster to focus.
- : Wide end: 10 cm to infinity
Tele end: 80 cm to infinity
(Total)
* : 80 cm to infinity (Normal)
+ : 2 cm to 60 cm (Super Macro)
2
Select the desired icon from the focus menu, and press the SET
button.
e This completes the focus range setting.
Note
About the scene select function and focus range settings
e The scene select function changes to = when the focus range is set to
* or +.
e Even if you set the focus range to * or +, it changes to - when the
scene select function is set to anything other than =.
About focus range in the BASIC mode
e In the BASIC mode, the focus range setting is automatically set to -.
When the distance between the camera and the subject is short, the focus
range automatically changes to the macro setting.
English 82
FLICKER-REDUCTION FUNCTION
The flicker-reduction setting reduces the flicker that results when filming video
clips under fluorescent lights and the like where the background lighting
pulsates at the frequency of the power supply. The flicker-reduction setting is
set for a frequency of 50 Hz.
1
Display the EXPERT Mode
Shooting Setting Screen (page 78),
and select the flicker-reduction
menu.
FLICKER REDUCT
OFF
p : Turns off the flicker-reduction
setting.
o : Turns on the flicker-reduction
setting.
2
Select the o icon from the flicker-
reduction menu, and press the SET
button.
e This completes the flicker-
reduction setting.
HINT
e If the flicker-reduction setting is used outdoors on a very bright day, a
halation effect may occur.
83 English
ISO SENSITIVITY
With the initial settings, the ISO sensitivity is automatically set according to the
brightness of the subject. However, the ISO sensitivity can be set to a fixed
setting.
1
Display the EXPERT Mode
Shooting Setting Screen (page 78),
and select the ISO sensitivity
menu.
ISO
AUTO
t : Sets the ISO sensitivity
automatically (equivalent to
ISO50 to 200 (Video clip
shooting mode: ISO200 to
800)).
* : Sets the sensitivity to ISO50
equivalent (Video clip shooting
mode: ISO200).
u : Sets the sensitivity to ISO100 equivalent (Video clip shooting mode:
ISO400).
v : Sets the sensitivity to ISO200 equivalent (Video clip shooting mode:
ISO800).
w : Sets the sensitivity to ISO400 equivalent (Video clip shooting mode:
ISO1600).
2
Select the desired icon from the
ISO sensitivity menu and press the
SET button.
e This completes the ISO sensitivity
setting.
HINT
e By setting a higher ISO sensitivity, you can set higher shutter speeds and
capture images in darker locations, but noise in the captured images may
increase.
English 84
WHITE BALANCE SETTING
This camera automatically adjusts the white balance under most lighting
conditions. However, if you want to specify the lighting conditions or change the
overall tone of the image, the white balance can be manually set.
1
Display the EXPERT Mode
Shooting Setting Screen (page 78),
and select the white balance menu.
WHITE BALANCE
AUTO
> : The camera will make the white
balance adjustment
automatically based on the
natural and artificial light
conditions. This is the setting
used in the auto mode.
r : For shooting outside on a sunny
day.
o : For shooting outside on a
cloudy day.
p : For shooting inside under
fluorescent lighting.
q : For shooting inside under
incandescent lighting.
2
Select the desired icon from the
white balance menu, and press the
SET button.
HINT
To cancel the white balance setting
e Perform step 1, select >, and then press the SET button.
85 English
EXPOSURE CORRECTION
When capturing images, you can make the image lighter or darker.
MENU button
Main switch
1
Set the main switch to REC, and set
the camera to the EXPERT
shooting mode (page 78).
e To exit the EXPERT Mode
Shooting Setting Screen, press the
MENU button.
2
3
When the EXPERT Mode Shooting
Setting Screen is not shown, toggle
the SET button to the left or right.
e The exposure correction bar
SET button
appears.
4
00:11
Toggle the SET button to the left or
right to adjust the exposure.
e To cancel the exposure correction
bar, press the MENU button.
e The exposure setting numerical
value is shown at the left end of the
exposure bar. The exposure can
be set to a value from –1.8EV to
+1.8EV.
0
HINT
The exposure correction setting is canceled in the following
cases:
e When the pointer is set to the center position.
e After the menu mode is changed.
e When the main switch is set to [PLAY].
e After the power is turned off.
English 86
PLAYBACK
ABOUT THE EXPERT MODE PLAYBACK
SETTING SCREEN
The EXPERT mode playback settings are performed on the EXPERT Mode
Playback Setting Screen.
Display the EXPERT Mode Playback Setting
Screen
Main switch
1
2
3
Turn on the camera (page 37).
Set the main switch to [PLAY].
Press the MENU button.
e The Menu Screen appears.
MENU button
4
Set the camera to the EXPERT
mode (page 42)
PLAYBACK METHOD
e The EXPERT Mode Playback
Set play all or 1
clip
Setting Screen appears.
e To cancel the EXPERT Mode
Playback Setting Screen, press the
MENU button.
87 English
EXPERT MODE PLAYBACK SETTING SCREEN
G
1
2
PLAYBACK METHOD
3
4
5
6
Set play all or 1
clip
H
7
I
8
9
F
1 Playback method setting (page
70)
9 Print settings (page 98)
e Set the DPOF settings.
e Select continuous playback or
F Option icon (page 105)
e Display the Option Setting Screen.
single-frame playback.
2 Multi-playback (page 66)
e Display images in the 9-frame
multi-display format.
G Menu mode display (page 42)
H Help display (page 107)
I Remaining battery power (page
126)
3 Volume control (page 71)
e Adjust the video clip and audio
data playback volume.
4 Monitor brightness (page 72)
e Adjust the brightness of the
camera’s LCD monitor display.
5 Data protect setting (page 73)
e Protect data from accidental
erasure.
6 Erase (page 75)
e Delete images from the card
memory.
7 Rotate image (page 89)
e Rotate still images.
8 Video clip edit (page 90)
e Edit video clips.
English 88
ROTATE IMAGE
Captured still images can be rotated to the correct orientation for viewing.
1
Display the EXPERT Mode
Playback Setting Screen (page 87).
ROTATE
2
Select the rotate icon L, and
press the SET button.
e The Rotate Image Screen appears.
K : Rotates image clockwise 90
degrees.
! : Rotates image
RIGHT
LEFT
EXIT
counterclockwise 90 degrees.
3
Select the rotate right icon K or
rotate left icon !, and press the
SET button.
e Each time the SET button is
pressed, the image is rotated
another 90 degrees.
89 English
EDITING VIDEO CLIPS
You can delete (“cut”) the first part or the last part of a video clip. You can
choose anywhere in the video clip as the cutting point.
You can also join two video clips together and save them as one separate clip
(“joining”).
Note
Warning concerning the battery pack remaining charge
e During the editing of lengthy video clips, the time to process the large
amount of data can become quite long. To avoid problems caused by the
battery pack becoming depleted in the middle of video clip editing, before
starting to edit be sure that a sufficiently charged battery pack is installed in
the camera, or connect the AC adapter/charger.
e It is recommended that a computer be used to edit long video clips.
Procedure to save part of a video clip as a
separate clip
Play the video clip, and pause playback
at the point you want to cut.
J
Select whether to delete the portion before the cut point or after the
cut point.
J
Delete the specified portion.
eThe specified portion is deleted.
eThe original video clip is not affected. (You
can also choose to erase the original video
clip when the new clip is saved.)
English 90
EDITING VIDEO CLIPS
Procedure to join two video clips
Display the video clip that will come
first.
J
Select the video clip that you wish to
append (join).
J
Join the video clips. (Press the SET button.)
eThe two video clips are saved together as
a separate video clip.
eThe original video clip is not affected. (You
can also choose to erase the original video
clip when the new clip is saved.)
Note
Caution when editing video clips
e When editing video clips, do not move the main switch. If you move the main
switch while editing video clips, not only will the editing not be properly
completed, but the original video clip may also be erased.
e By repeating the clipping and joining procedures, you can create exactly the
video clip you like. Note, however, that as the number or size of the video
clips increases, the card memory may become full, making it impossible to
edit the video clips. (The “CARD FULL” message will appear.) In this case,
you will need to free some of the memory on the card either by deleting data
that are no longer necessary (page 75), or by performing the procedure to
erase the original video clip(s) (page 94, 97).
91 English
Deleting part of a video clip
1
2
Display the video clip you wish to edit.
Display the scene you wish to delete.
e Specify whether you wish to delete the portion from the beginning of the
video clip up to the selected scene, or the portion from the selected
scene to the end of the video clip.
First part
Latter part
Video clip start
Selected scene
Video clip end
e To select the desired scene quickly, you can use a combination of the
fast-forward (or reverse) playback, pause, and image-by-image
playback functions (page 64).
e The actual cut point may be slightly before or after the displayed scene.
3
Display the EXPERT Mode
Playback Setting Screen (page 87).
Edit video clip
EDIT VIDEO
English 92
EDITING VIDEO CLIPS
EDIT VIDEO
4
Select the edit video icon k, and
press the SET button.
e The Edit Video Screen appears.
SAVE FRAME
DELETE 1ST PART
DELETE 2ND PART
JOIN
EXIT
EDIT VIDEO
5
Toggle the SET button up or down
to select the portion you wish to
delete.
DELETE 1ST PART:
Delete the first part of the video
clip.
DELETE 2ND PART:
Delete the latter part of the video
clip.
SAVE FRAME
DELETE 1ST PART
DELETE 2ND PART
JOIN
EXIT
DELETE 1ST PART
6
Press the SET button.
e A screen appears for you to
confirm whether or not you want to
save the original video clip.
KEEP ORIGINAL IMAGE?
YES
NO
EXIT
93 English
7
8
Select whether you want the
original video clip to be erased
when clipping is executed.
YES:
The original video clip is saved.
NO:
The original video clip is not saved.
Press the SET button.
e If “YES” was selected, the edited
video clip is saved as a new video
clip.
e If “NO” was selected, the edited
video clip is saved as a new video
clip, and the original video clip is
erased.
e To return to the Playback Setting
Screen, press the MENU button, or
select the d icon and press the
SET button.
Note
e If the original video clip is protected, even if you select “NO” in step 7 and 8
and press the SET button, the original video clip will not be erased. If you
want it to be erased, you will need to first remove the protection.
English 94
EDITING VIDEO CLIPS
Joining two video clips
1
Display the first video clip.
Currently showing video clip
Video clip to be joined
Video clip start
Video clip end
2
3
Display the EXPERT Mode
Playback Setting Screen (page 87).
Select the edit video icon k, and
press the SET button.
e The Edit Video Screen appears.
EDIT VIDEO
4
Select the join icon x.
SAVE FRAME
DELETE 1ST PART
DELETE 2ND PART
JOIN
EXIT
95 English
Orange frame
5
6
Press the SET button.
100
e The 9-image playback display for
0001
0003
0004
video clips appears.
Toggle the SET button to move the
orange frame to the video clip that
you wish to join.
7
8
Press the SET button.
JOIN
Select whether you want the
original video clip to be erased
when clipping is executed.
KEEP ORIGINAL IMAGE?
YES:
The original video clips are saved.
NO:
The original video clips are not
YES
NO
EXIT
saved.
Confirmation screen for
saving the original video clip
English 96
EDITING VIDEO CLIPS
9
Press the SET button.
e The two video clips are saved together as a separate video clip.
e If “NO” was selected in step 8, the original video clips are erased when
the joined video clip is saved.
e Press the MENU button, or select the d icon and press the SET
button, to return to the Playback Setting Screen.
Extracting a still image from a video clip
While video clip playback is paused, you save a still image of the paused
scene.
1
2
Display the frame (paused) you wish to save as a single still image.
Select the edit video icon k from the EXPERT Mode Playback
Setting Screen, and press the SET button.
e The Edit Video Screen appears.
3
Select the save frame icon 7, and press the SET button.
e The frame that is currently displayed is saved as a still image.
Note
e If the original video clip is protected, even if you select “YES” in step 8 and
press the SET button, the original video clip will not be erased. If you want it
to be erased, you will need to first remove the protection.
97 English
PRINT SETTINGS (STILL IMAGES ONLY)
In addition to using your printer to print out still images captured with your
camera, as with conventional film, you can have prints made at shops offering
digital print services. Moreover, this camera is DPOF-compatible, so you can
use the camera to specify the number of prints, whether or not the date is
displayed on the print, and also to specify an index print.
Display the Print Settings Screen
PRINT SETTING
1
2
Display the EXPERT Mode
Playback Setting Screen (page 87).
ALL IMAGES
EACH IMAGE
INDEX
ALL CLEAR
Select the print settings icon b,
EXIT
and press the SET button.
e The Print Settings Screen appears.
ALL IMAGES:
The specified print settings apply to
all the still images on the card.
EACH IMAGE:
The print settings are specified for
each individual image.
INDEX:
All the still images are printed as
miniature images (thumbnail
images), several images on one
print.
ALL CLEAR:
Clear all the print settings. This
cannot be selected if no print
settings have been made for the
image.
EXIT:
Return to the Still Image Playback
Setting Screen.
English 98
PRINT SETTINGS (STILL IMAGES ONLY)
HINT
e To print with a printer or have the digital print service shop print out a still
image from a video clip, you must first save it (save frame) as a still image.
HINT
About the DPOF format
e DPOF (Digital Print Order Format) is a print order format. You can connect
your camera to a DPOF-compatible printer to produce your prints. You can
also set the print settings for the desired images, and then have the reserved
images printed automatically.
About the finished prints
e Images that have been rotated will be printed in their original orientation.
e The quality of the print output will differ depending on the print service and
printer used.
99 English
Specifying date imprinting and print quantities
You can specify print settings for each individual image (EACH IMAGE), or
apply the print settings to all the images on the card (ALL IMAGES).
1
2
Display the Print Settings Screen
(page 98).
PRINT SETTING
Select EACH IMAGE or ALL
IMAGES.
ALL IMAGES:
The set print settings are applied
only to the image currently
displayed.
ALL IMAGES
EACH IMAGE
INDEX
ALL CLEAR
EXIT
EACH IMAGE:
The set print settings are applied to
all the still images on the card.
ALL IMAGES
SETTINGS
DATE:
3
Press the SET button.
DATE
NO
1
e The Date/Number Print Screen
appears.
COPIES
COPIES:
e If EACH IMAGE was selected,
toggle the SET button to the left or
right to display the desired image
to print.
ADD TO PRINT SETTING
EXIT
e Under “SETTINGS” the settings
that are currently active for the
displayed image are shown. You
can toggle the SET button to the
left or right to confirm the print
settings for each image.
English 100
PRINT SETTINGS (STILL IMAGES ONLY)
4
Specify whether the date is
displayed on the print, and the
number of prints.
ALL IMAGES
DATE
SETTINGS
DATE:
<Specifying dated prints>
1 Toggle the SET button up or down
to select “DATE”.
NO
2 Press the SET button.
d The Print Date Screen appears.
3 Toggle the SET button up or down
to select the desired option.
YES:(2)
COPIES:
Print the date.
NO:(2)
Do not print the date.
4 Press the SET button.
d You are returned to the Date/
Number Print Screen.
<Specifying the number of prints>
1 Toggle the SET button up or down
to select “COPIES”.
ALL IMAGES
COPIES
SETTINGS
DATE:
2 Press the SET button.
1
COPIES:
d The Print Number Screen
appears.
3 Toggle the SET button up or down
to specify the number of prints.
d Toggle the SET button up or
down until the desired number of
prints is displayed.
4 Press the SET button.
d You are returned to the Date/
Number Print Screen.
101 English
ALL IMAGES
DATE
SETTINGS
DATE:YES
COPIES:1
5
Select “ADD TO PRINT SETTINGS”
and press the SET button.
NO
1
e The Confirm Print Settings Screen
COPIES
appears.
If the print settings are correct:
Select “EXIT”, and press the SET
button.
MODIFY PRINT SETTING
EXIT
If the print settings were changed:
Select “MODIFY PRINT
SETTING”, and press the SET
button.
Index print
Printing out many small images on one sheet is called an “index print.” This
is convenient for use as a list of the images you have captured.
PRINT SETTING
1
2
Display the Print Settings Screen
(page 98).
ALL IMAGES
EACH IMAGE
INDEX
ALL CLEAR
Select “INDEX”.
EXIT
English 102
PRINT SETTINGS (STILL IMAGES ONLY)
INDEX
3
Press the SET button.
e The Index Print Screen appears.
YES:
SET INDEX PRINT
Specify an index print copy.
EXIT:
Discontinue the setting procedure,
and return to the Print Setting
Screen.
YES
EXIT
4
Select “YES”, and press the SET
button.
e This completes the setting for the
index print. You are returned to the
Print Settings Screen.
Changing the print settings
ALL IMAGES
SETTINGS
DATE:YES
COPIES:1
1
Follow steps 1 to 4 on page 100
and 101.
DATE
NO
1
COPIES
MODIFY PRINT SETTING
EXIT
2
Select “MODIFY PRINT SETTING”,
and press the SET button.
103 English
Clearing all the print settings
Delete the print settings for all images.
PRINT SETTING
1
Display the Print Settings Screen
(page 98).
ALL IMAGES
EACH IMAGE
INDEX
ALL CLEAR
EXIT
2
3
Select “ALL CLEAR”.
ALL CLEAR
Press the SET button.
DPOF
9
e The Confirm All Clear Screen
appears.
CLEAR ALL SETTINGS?
YES:
Clear the print settings for all
images.
EXIT:
YES
EXIT
Cancel the clear procedure and
return to the Print Settings Screen.
4
Select “YES”, and press the SET
button.
e All the print settings are cleared
and you are returned to the Print
Settings Screen.
English 104
OPTION SETTINGS
CAMERA SETTINGS
ABOUT THE OPTION SETTING SCREEN
The Option Setting Screen is used to adjust various camera settings and is
common to both the BASIC and EXPERT modes.
To display the Option Setting Screen
1
Turn on the camera (page 37).
2
Press the MENU button.
e The Menu Screen appears.
OPTION MENU
3
Select the option icon 3, and
press the SET button.
GUIDANCE
OPERATION BEEP
USB SETTING
FILE No. RESET
CLOCK SET
e The Option Setting Screen
appears.
e To cancel the Option Setting
Screen and return to the Menu
Screen, press the MENU button.
LANGUAGE
TV SYSTEM
105 English
Option Setting Screen
1
GUIDANCE
2
3
4
5
6
7
OPERATION BEEP
USB SETTING
FILE No. RESET
CLOCK SET
LANGUAGE
TV SYSTEM
G
8
9
F
POWER SAVE
RESET SETTINGS
REFORMAT
1 Guidance setting (page 107)
e Set the help display and audio
guide on or off.
8 Power save function (page 119)
9 Reset camera settings (page
121)
2 Operation sounds setting (page
108)
e Reset the camera to the factory-
preset settings.
e Adjust the operation sounds
produced when the camera’s
buttons are pressed.
F Card reformat (page 122)
e Use the camera to reformat the
memory card.
3 USB setting (page 110)
G Remaining battery power (page
126)
e Specify whether a printer or a
computer is connected.
4 File number reset (page 111)
e Select the file number reset
function.
5 Date and time setting (page 114)
e Set the camera’s internal clock.
6 Screen language (page 117)
e Select the language in which the
LCD monitor messages are
displayed.
7 TV system setting (page 118)
e Select the type of video signal that
is output from the camera’s
DIGITAL/AV terminal.
English 106
GUIDANCE FUNCTIONS
You can set whether or not the help display is shown on the LCD monitor, and
whether the audio guide giving verbal operation instructions is enabled.
1
2
Display the Option Setting Screen
(page 105).
GUIDANCE
Select the guidance icon r, and
press the SET button.
HELP DISP
AUDIO GUIDE
EXIT
ON
ON
e The Guidance Setting Screen
appears.
HELP DISP:
Enable or disable the HELP
messages display.
AUDIO GUIDE:
Adjust the volume of the audio
guide. When set to “OFF”, the
audio guide is muted.
EXIT:
Cancel the setting mode, and
return to the Option Setting Screen.
3
Toggle the SET button up or down to select the desired setting, and
press the SET button.
e The setting screen for the selected parameter appears.
e Toggle the SET button up or down to change the setting for the
parameter, and press the SET button.
107 English
OPERATIONAL SOUNDS SETTING
This setting allows you to set whether or not a confirming audio signal sounds
when the operation buttons (still image shooting button, SET button, MENU
button, etc.) are pressed.
OPERATION BEEP
1
2
Display the Option Setting Screen
(page 105).
TURN ON/OFF
SHUTTER
KEY SW
ON
B
A
Select the BEEP icon ?, and
press the SET button.
EXIT
e The Operation Sounds Setting
Screen appears.
TURN ON/OFF:
Mute or enable the sound that is
produced when the power is turned
on or off.
SHUTTER:
Select the sound that is produced
when the still image shooting
button is pressed, or when a photo
is taken using the self-timer.
KEY SW:
Select the sound that is produced
when the SET button, MENU
button, etc. are pressed.
EXIT:
Return to the Option Setting
Screen.
English 108
OPERATIONAL SOUNDS SETTING
3
Toggle the SET button up or down to select the desired setting, and
press the SET button.
<If TURN ON/OFF is selected>
e The screen to turn the operation sounds on or off appears.
e Toggle the SET button up or down to select the desired setting, and
press the SET button.
ON:
Activates the operational sounds when the camera is turned on or off.
OFF:
Deactivates the operational sounds when the camera is turned on or
off.
<If SHUTTER or KEY SW is selected>
d
d
d
The screen to select the operation sounds appears.
Select from 8 different sounds (A to H).
You can press the still image shooting button to preview the selected
operation sound.
If “OFF” is selected, no sound is produced.
Toggle the SET button up or down to select the desired setting, and
press the SET button.
d
d
HINT
e If you keep the MENU button pressed and turn on the power, the screen to
set whether the operation sounds are enabled or disabled appears at once.
You may find this a convenient procedure to switch the setting in places you
do not want the operation sounds to be audible. If the operational sound is
set to “OFF”, the audio guide is also muted.
109 English
USB FUNCTION SETTING
Perform the USB setting when the dedicated USB interface cable is used to
connect your camera to another device. Two modes are available for the USB
connection function. The PC connection mode is selected when the camera is
connected to a computer and used as a card reader. Select the PictBridge
mode when the camera is connected to a printer.
USB SETTING
1
2
Display the Option Setting Screen
(page 105).
CARD READER
PICTBRIDGE
Select the USB setting icon ;,
and press the SET button.
e The USB Setting Screen appears.
CARD READER:
PC connection mode setting (page
129)
PICTBRIDGE:
PictBridge mode setting (page 139)
3
Select the correct mode for your
purpose, and press the SET button.
Note
e When the CARD READER mode is set and the camera is connected to a
computer, the multi-indicator lights green.
e When the PICTBRIDGE mode is set and the camera is connected to a
printer, the multi-indicator lights red.
English 110
FILE NO. RESET FUNCTION
If a reformatted card is used, the file name (image number) of the captured
image automatically begins from 0001. If the card is subsequently reformatted,
or if a different reformatted card is used, the file names again begin from 0001.
This is because the file number reset function is set to ON, and consequently it
results in more than one card containing images with the same numbers. By
setting the file number reset function to OFF, even if the card is reformatted or
the card is replaced with another card, the consecutive numbering of file names
continues from the last number recorded by the camera.
<File number reset function ON>
File name (image number)
Card A 0001, 0002 ...... 0012, 0013
Replace card
Card B 0001, 0002 ...... 0012, 0013
<File number reset function OFF>
File name (image number)
Card A 0001, 0002 ...... 0012, 0013
Replace card
Card B 00014, 00015 ..... 0025, 0026
111 English
e If Card B already has image data in it when it replaces Card A, file
names are assigned as follows.
d
When the highest image number on Card B (before replacing) is
lower than the highest image number on Card A: the file name of the
next recorded image continues from last file name recorded on Card
A.
Card A 0001, 0002 ...... 0012, 0013
Replace card
Card B 0001, 0002, 0014, 0015 ..... 0025, 0026
Previously recorded images
d
When the highest image number on Card B (before replacing) is
higher than the highest image number on Card A: the file name of the
next recorded image continues from last file name recorded on Card
B.
Card A 0001, 0002 ...... 0012, 0013
Replace card
Card B 0020, 0021, 0022, 0023 ..... 0025, 0026
Previously recorded images
English 112
FILE NO. RESET FUNCTION
1
2
3
Display the Option Setting Screen
(page 105).
FILE No. RESET
Select the file number reset icon
i.
ON
OFF
Press the SET button.
e The File Number Reset Screen
appears.
ON:
The file number reset function is
on.
OFF:
The file number reset function is
off.
4
Select “OFF”, and press the SET button.
e The file number reset function is deactivated.
Note
e Until the file number reset function is turned ON, consecutive file names are
assigned. It is recommended that the file number reset function be returned
to ON at the end of each photography session.
113 English
DATE AND TIME SETTING
The camera will record the date and time an image or audio recording is taken
so that you can display them during playback. Therefore, before capturing
images, make sure the correct date and time are set.
Example: To set the clock to 7:30 p.m. on December 23, 2003
1
2
Display the Option Setting Screen
(page 105).
CLOCK SET
DATE
Select the clock set icon C, and
press the SET button.
e The Clock Set Screen appears.
e The current date and time settings
are shown.
2003/10/01
00:00
TIME
DISP
Y/M/D
e Follow the procedures below to
enable or disable the date display
during playback, to set the display
format for the date, and to set the
date and time.
EXIT
e To return to the Option Setting
Screen, press the MENU button, or
select “EXIT” and press the SET
button.
English 114
DATE AND TIME SETTING
CLOCK SET
DATE
3
Set the date.
2003/12/23
1 Select “DATE”.
2 Press the SET button.
d The Set Date Screen appears.
3 Set the date to “2003/12/23”.
d The date is set in the following
order: Set the year _ Set the
month _ Set the day.
d Toggle the SET button left or
right to select year, month or
day. Toggle the SET button up or
down to increase or decrease
the number.
4 Press the SET button.
CLOCK SET
TIME
4
5
Set the clock.
1 Select “TIME”.
2 Press the SET button.
d The Set Time Screen appears.
3 Set the time to “19:30”.
d The time is set in the following
order: Set the hour _ Set the
minute.
19:30
d A 24-hour clock is used for the
time display.
4 Press the SET button.
CLOCK SET
DISP
Set the order in which the date is
displayed during playback.
1 Select “DISP”.
2 Press the SET button.
d The Set Date Format Screen
appears.
Y/M/D
3 Toggle the SET button up or down.
115 English
e Toggle the SET button up to change the displayed date order as
follows:
year/month/day
month/day/year
day/month/year
DISP OFF (no display)
Toggle the SET button down to change it in the reverse order.
e If “DISP OFF” is selected, the date the image was captured is not
shown during playback.
4 Press the SET button.
6
Select “EXIT”, and press the SET
button.
e The date and time setting is
completed, and you are returned to
the Option Setting screen.
Note
e Under normal conditions, while the battery pack is being replaced, an
internal battery will maintain the date and time settings. However, there is a
small chance the settings may be lost. (The backup will last for about 7
days.) It is recommended to check that the date and time settings are still
correct after replacing the battery pack and before shooting or recording of
any type (follow steps 1 and 2).
To correct the date and time settings
e After steps 1 and 2, select the line of the setting that you want to change,
press the SET button, and follow the steps in the respective paragraphs
above to change the setting.
English 116
SCREEN LANGUAGE
You can set the LCD monitor of your camera to display the messages in any
one of nine languages.
1
2
Display the Option Setting Screen
(page 105).
LANGUAGE
Select the language icon z, and
press the SET button.
ITALIANO
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
e The Language Screen appears.
: Select for Japanese.
ENGLISH: Select for English.
FRANCAIS: Select for French.
DEUTSCH: Select for German.
ESPAÑOL: Select for Spanish.
ITALIANO: Select for Italian.
: Select for Korean.
: Select for Chinese (traditional).
: Select for Chinese (simplified).
3
Select the desired language, and
press the SET button.
e You are returned to the Option Setting Screen.
HINT
e In the shooting mode, if you press and hold the MENU button, the screen in
step 2 appears, allowing you to set the screen language.
117 English
TV SYSTEM SETTING
This setting is to specify the type of image signal that is output from the
camera’s DIGITAL/AV terminal.
1
2
Display the Option Setting Screen
(page 105).
TV SYSTEM
Select the TV system icon j, and
press the SET button.
e The TV System Setting Screen
NTSC
PAL
appears.
NTSC:
Output NTSC video signals
PAL:
Output PAL video signals
3
Select the appropriate TV system,
and press the SET button.
Note
e If the TV system setting is not correct for the connected TV, you will not be
able to view the images on the TV.
When set to “PAL” and connected to a TV
Shooting: Images are displayed on the LCD monitor only and do not appear on
the TV.
Playback: Images are displayed on the TV only and do not appear on the LCD
monitor.
English 118
POWER SAVE SETTING
Your camera has a “power save” function whereby the power automatically
turns off after a specified period of inactivity. The power save function works to
conserve the battery pack power when the camera is not being used, or to
prevent the battery pack from dying if the camera has accidentally been left on.
You can specify the elapsed time (standby time) before the power save
function is activated.
1
2
Display the Option Setting Screen
(page 105).
POWER SAVE
BATT/CAM
Select the power save icon ?,
and press the SET button.
1 min
5 min
e The Power Save Setting Screen
BATT/PB
appears.
BATT/CAM:
EXT.PWR/CAM.PB
EXIT
10 min
Set the standby time for the
shooting modes when the battery
pack is used.
BATT/PB:
Set the standby time for the
playback modes when the battery
pack is used.
EXT.PWR/CAM.PB:
Set the standby time for the
shooting and playback modes
when using an AC power source.
EXIT:
Return to the Option Setting
Screen.
119 English
3
4
Select the desired option.
Press the SET button.
POWER SAVE
BATT/CAM
1 min
e The Set Standby Time Screen
appears.
5
6
Toggle the SET button up or down
to set the standby time.
<Example: When “BATT/
Up:
CAM” is selected>
Increases the standby time.
Down:
Decreases the standby time.
Press the SET button.
e The standby time is set, and you
are returned to the Power Save
Setting Screen.
English 120
RESETTING THE CAMERA SETTINGS
Reset the camera to the factory-preset settings.
1
2
Display the Option Setting Screen
(page 105).
RESET SETTINGS
Reset?
Select the reset settings icon 2,
and press the SET button.
e The Reset Settings Screen
appears.
YES:
YES
NO
Reset to the factory-preset
settings.
NO:
Do not change the settings, and
return to the Option Setting Mode
Screen.
3
Select “YES”, and press the SET
button.
e The camera settings are reset to
the factory-preset settings.
HINT
e Note that the following settings do not change with this procedure:
Date and time setting
Language setting
TV system setting
121 English
FORMATTING A CARD
The supplied card must be formatted with this camera. In addition, a card must
be formatted with this camera:
• After purchasing, when used for the first time, or
• If it was formatted using a personal computer or another digital camera.
The card cannot be reformatted if the lock switch is set to the “LOCK” position.
Proceed with the reformat procedure after setting the lock switch to the
unlocked position (page 26).
1
2
Display the Option Setting Screen
(page 105).
FORMAT
Select the reformat icon 1, and
press the SET button.
FORMAT
e The Reformat Screen appears.
e In normal use, a total format is not
necessary. However, in case a
card error occurs even after normal
formatting, executing a total
reformat may resolve the problem.
FORMAT:
FULL FORMAT
EXIT
A normal reformatting is executed.
FULL FORMAT:
The entire card is scanned and
reformatted. (When there is little
battery power remaining, this
setting cannot be selected.)
English 122
FORMATTING A CARD
3
Select the desired format option,
and press the SET button.
4
5
Select “YES”.
Press the SET button.
e Reformatting begins.
e During reformatting, “REFORMAT”
and “DO NOT POWER OFF” are
shown on the LCD monitor.
CAUTION
Caution during reformatting
e Do not turn off the power to the camera or eject the card during reformatting.
Reformatting erases the data
e When a card is reformatted, all data recorded on the card is erased.
Protected data (page 73) is also erased, so before reformatting a card, any
data you want to keep should be copied to your personal computer’s hard
disk or other storage medium.
HINT
To cancel reformatting
e In step 4, select “EXIT”, and press the SET button.
123 English
CHECKING THE REMAINING CARD MEMORY
You can check how many images can be captured and how much recording
time is available on the card. For a table showing the maximum number of
images and recording time for specific cards, please see “Possible No. of
Images/Possible Shooting Time/Possible Recording Time” on page 167.
Checking the remaining number of images and
video recording time
Remaining number of images
1
Set the main switch to REC, and
turn on the power (page 37).
Remaining video
recording time
e The remaining number of images
appears in the upper left of the
LCD monitor.
6
00:09
e The remaining video recording time
appears in the upper right of the
LCD monitor.
e The remaining number of images
and video recording time will differ
depending on the resolution and
compression settings.
e When the remaining number of
images or the remaining video
recording time is “0”, you cannot
capture any more images. To
capture more images, either install
a new card, or save the images to
a computer (page 129) and then
erase them (page 75) from the
card.
<Still image shooting mode>
e When the remaining number of images or the remaining video
recording time is “0”, it may be possible to capture a few more images
by setting a lower resolution setting (pages 55, 56), or selecting a
different compression setting.
English 124
CHECKING THE REMAINING CARD MEMORY
For audio data
100-0004
96KB
INFO
1
Display the Audio Data Information
Screen (page 77).
e The remaining card memory is
shown.
AAC
00:00:03
UNUSED MEMORY 21%
2003.12.25 19:30
125 English
CHECKING THE REMAINING BATTERY PACK
CHARGE
When using the battery pack, the remaining battery pack charge can be
checked on the LCD monitor. Make sure to check this indicator before
capturing an image. For an indication of the possible length of time for battery
pack operation, see page 166.
1
Display a Shooting or Playback
Setting Screen (pages 52, 68, 78,
87).
VIDEO CLIP MPEG4
640¶480 30fps HQ
e The battery pack remaining charge
indicator appears in the lower right
corner of the LCD monitor.
e Due to the battery pack
characteristics, when the ambient
temperature is low, r may
appear early for an incorrect
indication of the remaining charge.
Also, depending on the conditions
of use of the camera or the ambient
conditions (temperature, etc.), the
indicated remaining charge may
change. Therefore, this indication
can only be used as a general
approximation of the remaining
charge.
Battery pack remaining
charge indicator
Battery pack remaining charge indicator
r
Approx. full.
r
Power is low.
It will soon be impossible to capture or play back
images.
r
r
If this icon flashes when the still image shooting
button or video clip recording button is pressed,
images cannot be captured. Recharge the battery
pack.
English 126
CHECKING THE REMAINING BATTERY PACK CHARGE
HINT
e If any data is present, you can also check the remaining battery pack charge
on the Playback Screen.
e Use only the supplied or separately sold battery pack in this camera.
e Battery life may differ even among battery packs of the same type.
e Depending on the usage of the camera (such as the number of times the
flash is used, the use of the LCD monitor, etc.) or the ambient temperature
(temperatures below 10°C) the number of images that can be saved on a
fully charged battery pack will vary greatly.
Note
e It is recommended that you prepare an extra battery pack(s) when taking
pictures at a wedding or while traveling, for example, so you don’t miss
capturing images of important moments due to the battery pack power
running out. The same is recommended for taking photos in cold
environments. (In a ski area, for example, the battery pack can be kept warm
in your pocket until ready to use.)
127 English
OTHER DEVICES AND CONNECTIONS
DOCKING STATION
Set your camera in the supplied docking station to recharge the battery pack as
well as for easy connection to a computer, printer or TV. A remote control unit is
provided for even easier operation of your docked camera (playback only).
CAUTION
Gently connect and disconnect the cable
e When connecting and disconnecting the cable, please do so with a gentle
touch. Exerting a strong pull on the cable or connector may damage them.
Connecting the docking station
Connect the AC adapter/charger
Use the supplied AC adapter/charger to connect the DC IN terminal on the
docking station to a power outlet.
To AC
English 128
DOCKING STATION
Connect to another device
<To connect to a computer or printer>
Use the supplied USB interface cable to connect the DIGITAL/AV terminal of
the docking station to the USB terminal of a computer or printer.
e Connect the dedicated USB interface cable to your computer’s USB
connector. Do not connect it to the USB port on your monitor or
keyboard, or to the USB hub. Be especially careful when installing the
driver software. In some instances, it may not be possible to correctly
install the driver software.
e Please refer to the included Sanyo Software Pack instruction manual
for information regarding operating your camera from a computer.
Supplied USB interface cable
To USB connector on the computer or printer
DIGITAL/AV terminal
<To connect to a TV>
Use the supplied AV cable to connect the DIGITAL/AV terminal of the
docking station to the audio and video terminals of a TV.
e After connecting the camera to the television, set the TV input switch to
VIDEO input.
e The remote control unit can be used for playback.
e The playback method is the same as when viewing images on the LCD
monitor.
e The same playback procedure as when playing back with the camera is
used to play back audio recordings as well.
129 English
Yellow plug:
To Video Input terminal
Supplied AV cable
DIGITAL/AV terminal
White plug: To Audio Input (LEFT) terminal
Red plug: To Audio Input (RIGHT) terminal
Data file formats
The format of the files saved on the card and the method in which the file
names are determined are explained below.
Type of data
Data format
File name structure
File name begins with SANY.
Extension is “.jpg”.
SANY****.jpg
Still image data JPEG
File name begins with VCLP.
Extension is “.mp4”.
VCLP****.mp4*
Video clip data
MPEG-4
MPEG-4 Audio File name begins with SUND.
Audio recording
data
(AAC
Extension is “.m4a”.
compression)
SUND****.m4a*
*Consecutive numbers assigned in the order the data was saved.
English 130
DOCKING STATION
Configuration of directories for the stored data
ROOT
DCIM
100SANYO
SANY0001.jpg
SANY0002.jpg
VCLP0003.mp4
SANY0004.wav
SANY0005.jpg
Image number
Folder number
MISC
(Location of
DPOF files)
Video clip or
audio
recording
number
101SANYO
102SANYO
SANY0001.jpg
SANY0002.jpg
SANY9999.jpg
SANY0001.jpg
SANY0002.jpg
* Up to 9999 files can be stored in folder 100SANYO. If more files are made, a folder
named 101SANYO is created, and they will be stored in there. New folders will then be
named in sequence, i.e., 102SANYO, 103SANYO, etc.
Note
About video clip data recorded with this camera
e You can use Apple’s QuickTime 6.1 or later version to play back video clips on a
computer. Playback may also be possible using other software that supports the
ISO standard MPEG-4 (AAC audio). QuickTime6.3 for Windows and Macintosh
is supplied with the included CD-ROM (Sanyo Software Pack).
About audio data recorded with this camera
e If you change the extension (.m4a) of audio data files to “.mp4”, playback
may be possible using software that supports the ISO standard MPEG-4
(AAC audio).
About file names when the card is replaced...
e If the file number reset function is set to off, even when the card is replaced,
consecutive numbering of folder numbers and file names continues from the
previously installed card (page 111).
CAUTION
If you intend to view the images on the camera, do not use a
computer to rewrite the card data.
e If the folders, file names, or their configuration is modified using a personal
computer, it will be impossible to play back the data using the camera, and
the camera may not operate properly.
131 English
Set the camera in the docking station
1
Close the camera’s monitor unit,
and set it in the docking station.
e Note the camera’s orientation and
the position of the docking station
terminals, and insert the camera
firmly.
e Recharging begins as soon as the
camera is set in the docking
station.
e During charging, the charging
indicator lights red. When charging
is complete, the charging indicator
lights green.
e If there is a battery malfunction or if the camera is incorrectly set in the
docking station, the charging indicator flashes red, and the docked
camera’s multi-indicator flashes red. Set the camera in the docking
station correctly.
Preparing and using the remote control unit
Use the supplied remote control unit to play back data from the docked
camera.
Prepare the remote control unit
The remote control unit comes with the battery already installed at the time
of purchase.
1
Pull out and remove the protective
battery insulating sheet.
e The remote control unit becomes
operative when the insulating sheet
is removed.
English 132
DOCKING STATION
How to use the remote control unit
The remote control unit can be used at an angle that is displaced 15 degrees
horizontally from the remote control sensor on the front of the docking
station, at a distance of up to 7 meters.
At a distance of up to 7 meters
Infrared emitter
15˚
Remote control
15˚
sensor
15˚ horizontally
CAUTION
e If the remote control unit is operated in sunlight or under inverter lighting, the
remote control receiving range may become shorter. This is a characteristic
of the infrared remote control unit and is not a defect. To avoid this
malfunction when operating the remote control unit, take care to shield the
remote control sensor from strong light.
133 English
<Remote control unit button operation>
1
CH.
MENU
2
3
5
6
SET
4
7
1 CH (channel)
e Switch the remote control code (page 136).
2 SET
e Same operation as the camera’s SET button.
3 MENU
e Same operation as the camera’s MENU button.
4 [G]
e Works the same as toggling the camera’s SET button to the left.
5 [I]
e Works the same as toggling the camera’s SET button up.
6 [H]
e Works the same as toggling the camera’s SET button to the right.
7 [J]
e Works the same as toggling the camera’s SET button down.
English 134
DOCKING STATION
Replacing the remote control unit battery
The life of the lithium battery will depend on your use of the remote
control unit, but as a general guideline, it will require replacement about
once a year. Follow the steps below to replace the CR2025 Lithium
battery (sold commercially).
1
Pull out the battery holder from the
remote control unit.
e Push in the tab to release the
battery holder, and then pull it out.
2
3
Remove the battery.
Insert a new battery (CR2025) in the
holder.
e Wipe the new battery with a soft,
dry cloth, and then insert it with the
(+) mark facing upward.
4
Reinsert the battery holder in the
remote control unit.
135 English
Changing the remote control code
The remote control unit will also work with other Sanyo cameras that can be
operated by infrared remote control. When more than one camera is
present, it is recommended to change the remote control code to ensure that
only the intended camera operates when the remote control unit is used.
The remote control code is set to “RC CODE 1” at the time of purchase.
<Changing the remote control code from “RC CODE 1” to “RC
CODE 2”>
1
2
3
Aim the infrared emitter at the remote control sensor on the docking
station.
Hold down the CH button and press the [I] button for about 3
seconds.
Press a button on the remote control unit and check that the camera
is receiving correctly.
e The remote control codes are retained even if the batteries in the
remote control unit and camera are replaced.
e If the remote control codes for the remote control unit and the camera
and do not match, the remote control unit cannot be used to operate
the camera.
English 136
DOCKING STATION
<Resetting the remote control code to “RC CODE 1”>
1
2
Aim the infrared emitter at the remote control sensor on the docking
station.
Hold down the CH button and press the [J] button for about 3
seconds.
Select the image to play back.
1
2
Connect the docking station to a TV, and set the camera in the
docking station.
Press the CAMERA/CHARGE button to turn on the camera lamp.
CAMERA/CHARGE button
Camera indicator
3
Set the TV input switch to VIDEO input.
e If the camera is set to the playback mode, the Playback Screen
appears on the TV monitor. The playback method is the same as when
viewing images on the LCD monitor.
137 English
CABLE ADAPTER
When not using the docking station, you can connect the camera to a
computer, printer, TV or AC adapter/charger, etc, using the supplied adapter.
1
2
Attach the adapter to the docking station terminals on the bottom of
the camera.
Various devices can be connected to the adapter terminals
DC IN terminal:
Connect the supplied AC adapter/charger.
DIGITAL/AV terminal:
Connect to a computer, printer or TV.
To docking station terminal on the camera
Supplied USB interface cable
or AV cable
Supplied AC adapter/charger
Note
The remote control unit cannot be used.
e Unlike when using the camera in the docking station, when the adapter is
connected, the remote control unit cannot be used to operate the camera. To
play back data from the camera, use the operation buttons on the camera.
The battery cannot be recharged.
e When recharging the battery pack that is installed in the camera, set the
camera in the docking station. To recharge the battery pack without using
the docking station, remove the battery pack from the camera and set it in
the AC adapter/charger to recharge it.
English 138
CONNECTING TO A PRINTER
Your camera supports the PictBridge function. By connecting the camera
directly to a PictBridge-enabled printer, the camera’s LCD monitor can be used
to select images and initiate printing.
Print preparations
1
Install the card containing the images you want to print in the
camera.
2
Use the supplied docking station or adapter to connect the camera to
the printer (pages 132 and 138).
Supplied USB interface cable
To USB connector on the printer
DIGITAL/AV terminal
139 English
<Using the docking station>
e Set the camera in the docking station, and press the CAMERA/CHARGE
button to turn on the camera indicator.
e When the connections are complete, turn on the printer, and confirm that the
camera’s multi-indicator is lit red. When the multi-indicator is lit green, it is
not possible to print.
Multi-indicator
CAMERA/CHARGE button
Camera indicator
<Using the cable adapter>
e After attaching the cable adapter, set the camera’s main switch to PLAY.
WARNING
Do not turn off the power to the printer while it is connected.
e If the power to the printer is turned off while it is connected, the camera may
not operate correctly. If the camera does not operate correctly, disconnect
the USB interface cable, turn off the camera, and then reconnect the cable.
English 140
CONNECTING TO A PRINTER
PRINTING MODE
ONE IMAGE
3
The PictBridge printing mode is
activated.
e The camera switches to the
PictBridge printing mode, and the
PictBridge Screen appears.
Print this image
CAUTION
e During PictBridge printing, the camera’s button operation response is slower.
e If the camera is powered by batteries for printing, make sure that the
remaining battery charge is sufficient.
141 English
To select one image and print it (one image)
Procedure to select one still image and print it.
1
2
Complete the printing setup (page
139).
ONE IMAGE
COPIES
100-0002
Select the choose one image icon
Y, and press the SET button.
1
e The screen to select images for
printing appears.
PRINT
EXIT
3
Toggle the SET button to the left or
right to display the image you with
to print.
e Specify the image to print.
English 142
CONNECTING TO A PRINTER
ONE IMAGE
COPIES
100-0002
4
Specify the number of prints.
1 Select “COPIES”, and press the
SET button.
1
2 Toggle the SET button up or down
to specify the number of prints.
3 Press the SET button.
e “PRINT” is selected.
5
Press the SET button.
e Printing begins.
Note
To cancel printing
e During printing, toggle the SET button down.
d
d
The Confirm Cancel Printing Screen appears.
e Select “YES”, and press the SET button.
If “NO” is selected and the SET button is pressed, printing resumes.
143 English
To print all the images (all images)
Print all of the images on the card.
1
2
Complete the printing setup (page
139).
ALL IMAGES
100-0002
Select the print all images icon
u, and press the SET button.
e The Print All Images Screen
appears.
PRINT
EXIT
3
Select “PRINT”, and press the SET
button.
e Printing begins.
Note
Printing is not possible if there are more than 999 still images in
the card.
e Delete unwanted images before printing.
English 144
CONNECTING TO A PRINTER
Thumbnail prints (index)
Make an index print of all the images on the card.
1
2
Complete the printing setup (page
139).
INDEX
100-0002
Select the index print icon [, and
press the SET button.
e The Index Print Screen appears.
PRINT
EXIT
3
Select “PRINT”, and press the SET
button.
e Printing begins.
145 English
To print the images that are set to print
(print reserved images)
Procedure to print all the images that are set to print.
1
2
Make the print settings (page 98),
and complete the printing setup
(page 139).
CONFIRM IMAGES 100-0002
Select the print reserved images
icon w, and press the SET
button.
9
DPOF
DATE
INDEX
e The Confirm Print Images Screen
appears.
PRINT
EXIT
3
Select “PRINT”, and press the SET
button.
e Printing begins.
e Printing begins about 1 minute
after the SET button is pressed.
e During printing, the remaining
number of images to be printed is
shown on the LCD monitor.
HINT
e In step 2, if you toggle the SET button to the left or right, you can confirm the
images that are set to print and their DPOF settings.
English 146
CONNECTING TO A PRINTER
To change the printer settings and print
images (change printer settings)
Images are printed according to settings specified by the camera, such as
paper type, size, layout, printing quality, etc.
1
2
Complete the printing setup (page
139).
PRINTER SETTINGS
Select the change printer settings
icon v, and press the SET
button.
MEDIA TYPE
PRINTER VALUE
PRINTER VALUE
PRINTER VALUE
PRINTER VALUE
PRINTER VALUE
PAPER SIZE
LAYOUT
e The Printer Settings Screen
QUALITY
appears.
DATE STAMP
MEDIA TYPE:
Specify the type of paper used for
EXIT
printing.
PAPER SIZE:
Specify the size of paper used for
printing.
LAYOUT:
Specify how the images are to be arranged on the paper.
QUALITY:
Select the print quality for the images.
DATE STAMP:
Print the date the photo was taken.
EXIT:
Return to the Printing Mode Screen.
147 English
3
Adjust the printer settings.
1 Toggle the SET button up or down
to select a printer setting
parameter, and press the SET
button.
d The screen to set the selected
parameter appears.
2 Toggle the SET button up or down
to adjust the setting, and press the
SET button.
d The selected parameter is set,
and you are returned to the
Printer Settings Screen.
d Follow the same procedure to
adjust the other parameters, as
desired.
d The contents of the settings that
can be made for each parameter
will differ depending on the
printer.
<When “PRINTER VALUE” is selected>
d The images will be printed
according to the settings
specified on the printer side.
4
Select “EXIT”, and press the SET
button.
e You are returned to the Printing
Mode Screen.
Note
e The printer setting parameters will differ depending on the printer that is
connected.
e To use printer functions which do not appear on your camera’s Printer
Settings Screen, select “PRINTER SETTINGS”.
e If a function set by the camera is not available in the printer, the camera’s
printer settings will automatically change to “PRINTER SETTINGS”.
English 148
APPENDICES
COMMONLY ASKED QUESTIONS
If you have a question about the camera operation, you might find the answer
in this compilation of commonly asked questions.
Question
Cause
Action
Why doesn’t the Due to cold
power turn on? temperatures, the
battery pack
Place the camera in
your pocket to warm it
up before using it.
temporarily lost its
power.
Why is the
The ambient
temperature is very
low.
Keep the battery pack
in an environment of 10
to 40°C.
battery pack
consumed so
quickly even
after it was fully
recharged?
Why doesn’t
recharging end? has expired.
The battery pack life
Replace with a new
battery pack. If this is
not effective, consult
your dealer.
Power
Why does the
The remaining battery Use the supplied AC
pack power is low.
adapter/charger, or
replace the battery
pack with a fully
charged one.
r
icon
appear?
While the flash is Battery pack power is Not a malfunction.
recharging, why low, activating the
When the flash is fully
charged, the LCD
monitor will turn on
again.
does the LCD
monitor
function that
momentarily turns off
the LCD monitor.
suddenly turn
off?
149 English
Question
Cause
Action
Why does the
multi-indicator
light red?
Recorded data is being Not a malfunction.
saved on the card.
Wait until the multi-
indicator turns off.
Why doesn’t the The camera has
Not a malfunction.
Capture the image; the
flash operate?
determined that the
image is bright enough camera will determine
and the flash is not
necessary.
when the flash is
necessary.
Are the settings
retained even
after the camera
is turned off?
All settings except the
self-timer and the
exposure correction
are retained even after
the camera is turned
off.
—
Shoot-
ing
Which resolution
setting should I
use?
Select the resolution
setting according to the
intended use:
Y: Appropriate for
printing letter-size or
larger, and for printing
a close-up of part of a
photo (trimming).
—
Z: For printing
standard photo (photo
service) sizes.
[: For photos
displayed on a web
page, or sent as e-mail
attachments.
English 150
COMMONLY ASKED QUESTIONS
Question
Cause
Action
What is the
difference
between the
digital zoom and
the optical
zoom?
Because shooting with
the optical zoom uses
the optics of a physical
lens, you can shoot
without losing minute
details in the image.
The digital zoom, on
the other hand, works
by magnifying a portion
of the image that hits
the CCD sensor and
may produce a coarser
image.
—
How can I get
the distant view
into focus?
Set the scene select
function to the
Shoot-
ing
—
—
landscape + mode
when photographing.
The video clip I
shot outdoors is
completely
Set the flicker-
reduction setting to off
p.
white.
Why does the
The resolution setting Not a malfunction.
resolutionsetting is fixed at [ when
automatically
the scene select
function is set to Q or
change to [
when the scene the filter is set to (.
select function is
set to Q or the
filter is set to
(?
151 English
Question
Cause
Action
Why does the
flash setting
automatically
change to l
The flash setting is
Not a malfunction.
fixed at l when the
scene select function is
set to Q or the filter is
when the scene set to (.
select function is
set to Q or the
filter is set to
Shoot-
ing
(?
Why doesn’t the The digital zoom is
Not a malfunction.
digital zoom
work when the
filter is set to
5 or (?
deactivated in these
filter modes.
When used in
cold weather,
why does the
image seem to
leave traces as it
moves?
Condition due to the
liquid crystals.
Not a malfunction.
Spots that appear in
the LCD monitor only
appear in the monitor
and will not be
recorded with the
LCD
monitor
Monitor
images.
Why does the
displayed image
contain some
red, blue and
green dots, or
black spots are
visible?
Why is the
image too
bright?
The subject was too
bright.
When capturing an
image, devise a way to
compensate for a
Viewing
images
bright subject, for
example, by changing
the shooting angle.
English 152
COMMONLY ASKED QUESTIONS
Question
Why is the
image out of
focus?
Cause
Action
The focus is not locked Hold the camera
properly.
correctly and slowly
press the still image
shooting button
halfway to lock the
focus. Then press the
still image shooting
button all the way to
capture the image.
Why is a part of The image was
When capturing an
image at close range,
compose the image
using the LCD monitor.
the image
missing?
captured at close
range.
Why is there no This may happen when Play back images that
Viewing
images
image (z is
trying to play back
images stored on a
card from a different
digital camera.
were recorded on a
card using this camera.
shown)?
Why do vertical If a bright subject is
stripes appear? shot in the video clip
shooting mode, vertical
Not a malfunction.
Not a malfunction.
stripes may appear on
the LCD monitor or in
the image.
Why isn’t the
Due to the
magnified image characteristics of the
clear?
camera, magnified
images appear less
clear.
153 English
Question
Cause
Action
Why isn’t the
The image was
Not a malfunction.
captured image captured using the
clear?
digital zoom.
Can I play back
image and
sound data that I
edited using my
computer?
We cannot guarantee
the accurate playback
of data that has been
edited using a
—
Viewing
images
computer.
Why is there a
The sound of the
Not a malfunction.
motor-like sound camera’s mechanical
during video clip action was recorded.
playback?
Why is there no The volume on the TV Adjust the volume on
Con-
necting
to a TV
sound?
is set to the minimum. the TV.
The volume of the
camera is set to 0.
Increase the playback
volume of the camera.
Why does a
There is a problem with Please refer to the
message appear the printer.
Printing during
PictBridge
printing?
instruction manual for
your printer.
The “CAN NOT You have attempted to Select video clips that
EDIT VIDEO”
message
appears.
join video clips having have the same
different resolutions or resolution or frame
Image
editing
frame rates.
rates.
English 154
COMMONLY ASKED QUESTIONS
Question
Cause
Action
Why is a noise
heard from a
nearby TV or
radio during
battery
Electromagnetic waves Move the AC adapter/
are emitted from the
AC adapter/charger.
charger further away
from the TV or radio
when recharging
batteries.
recharging?
Why does the
“CARD FULL”
message
There is no more
available memory on
the card.
Erase unnecessary
data.
Use a card that has
more memory
available.
appear?
Why does the
“CARD IS
PROTECTED”
message
The lock switch on the Move the lock switch to
card is in the locked
(protect) position.
the unlocked position.
appear?
Misc.
Why can’t the
camera be
operated?
A temporary internal
Remove the battery
circuitry problem may pack from the camera,
be the cause.
wait a few minutes,
then reinstall the
battery pack and try
again.
Can I use my
camera abroad?
When the camera is
connected to a TV, you
can switch the
camera’s video output
to NTSC or PAL. If you
have questions about
using the AC adapter/
charger and power
cord abroad, please
consult with a dealer
near you for advice.
—
155 English
Question
Cause
Action
Why does the
“SYSTEM
ERROR”
message
appear?
A problem has
occurred within the
camera or card.
Check the following
items
1 Remove the card
and then install it
again.
2 Remove the
batteries and then
install them again.
3 Install a different
card.
Misc.
If “SYSTEM ERROR”
still appears after
performing the above
steps, then take the
camera to the dealer
for service.
English 156
TROUBLESHOOTING
Before taking your camera to the repair shop, check the following table for a
possible solution to the problem.
CAMERA
Refer-
ence
page
Problem
Cause
Action
No power.
The battery pack is Recharge the battery
dead.
pack, or replace with
a new battery pack.
34,
35
The battery pack
has not been
inserted correctly.
Reinsert the battery
pack, making sure to
orient it correctly.
The camera
turns off by
itself.
The power save
function is
operating.
Press one of the
operation buttons
once.
38
The camera is
set in the
dockingstation,
but it does not
recharge.
If a battery pack is
set in the AC adapter/
charger, the battery
pack in the AC
adapter/charger is
recharged first, after
which the battery
pack in the camera
starts to recharge. To
speed up recharging
of a battery pack, set
it in the AC adapter/
charger.
Power
—
157 English
Refer-
ence
Problem
Cause
Action
page
An image is not The power is not
captured when turned on.
the still image
When the power
save function is
active, after pressing
one of the buttons to
shooting button
or video clip
recording
button is
pressed.
turn on the camera, if 38
the shooting power is
off, press the ON/
OFF button to turn it
on.
An image is not The maximum
captured when number of images
the still image that can be captured
shooting button or the maximum
Install a new card.
36
Erase the images
that are not
necessary.
Save the images to
separate media, then
erase all the images
from the card.
75,
129
or video clip
recording
button is
video clip recording
time has been
reached.
Shoot-
ing
pressed.
The flash does The flash off mode Set the flash to
not operate.
is selected.
automatic flash mode 60
or forced flash mode.
The flash does The battery pack is Recharge the battery
34,
35
not operate.
dead.
pack, or replace with
a new battery pack.
The lamp mode Q Set to a different
58
is active.
mode.
A warning tone The battery pack is Install a sufficiently
(beep-beep-
beep) sounds,
and it is not
consumed.
recharged battery
pack.
34,
35
possible to take
a picture using
the self-timer.
English 158
TROUBLESHOOTING
Refer-
ence
Problem
Cause
Action
page
When zooming The optical zoom
Not a malfunction.
Release the zoom
switch, and press it
again.
in or out, the
zoom
has moved to the
maximum
61
movement
stops
magnification
position.
Shoot-
ing
momentarily.
There is noise The ISO sensitivity Set the ISO
in the captured setting is too high.
image.
sensitivity to a lower
setting.
84
64
No playback
image appears. not set to PLAY.
The main switch is
Set the main switch
to PLAY.
LCD
monitor
The image is
too dark.
The flash was
blocked by a finger correctly, and make
or other object.
Hold the camera
44
sure the flash is not
obstructed.
The subject was too Capture the image in
far away.
the range of
165
operation of the flash.
The subject was lit
from behind.
Use the forced flash
mode.
60
86
84
Use the exposure
correction function.
View-
ing
images
There is not enough Adjust the ISO
light.
sensitivity setting.
The video clip The video clip was
Set the flicker-
reduction setting to
picture is
flickering.
filmed under
fluorescent lighting. on.
83
The image is
too bright.
The forced flash
mode is selected.
Select a different
flash mode.
60
86
84
The subject was too Use the exposure
bright. correction function.
The ISO sensitivity Set the ISO
setting is incorrect. sensitivity to t.
159 English
Refer-
ence
Problem
Cause
Action
page
The image is
not in focus.
The subject is too
close to the camera. focus setting for your
Select the correct
82
needs.
The focus setting is
not correct.
The camera moved Hold the camera
when the still image correctly and slowly
shooting button was press the still image
pressed.
shooting button
44,
48
halfway to lock the
focus. Then press the
still image shooting
button all the way to
capture the image.
The focus is not
locked properly.
The lens is dirty.
Clean the lens.
22
View-
ing
images
The colors of
the images
captured
This is due to
ambient lighting.
Capture the image
using the forced flash 60
mode.
indoors are not
correct.
The white balance
setting is incorrect. setting correctly.
Set the white balance
85
A part of the
image is
missing.
The handstrap or a Hold the camera
finger was blocking correctly, and make
44
the lens or lens
opening.
sure the lens is not
obstructed.
“NO IMAGE” is There is no recorded Play back after
shown.
data for the selected capturing images or
47
71
playback mode.
making audio
recordings.
During audio
The volume setting Select the volume
playback, there on the camera is too icon Z and adjust
is no sound. low. the volume.
English 160
TROUBLESHOOTING
Refer-
ence
Problem
Cause
Action
page
No image or
sound.
The digital camera is Follow the
not correctly
instructions to make
connected to the TV. the connection
correctly.
130
The TV input is not Set the input on the
set correctly.
TV to “VIDEO”.
Con-
necting
to a TV
The TV system
setting is not correct. system.
Set to the correct TV
118
71
There is no
sound.
The volume setting Select the volume
on the camera is too icon Z and adjust
low.
the volume.
The edge of the This is a
image is cut off. characteristic of the
TV.
Not a malfunction.
129
73
You cannot edit The protect mode is Cancel the protect
Image
editing
or rotate an
image.
set.
mode.
The “NO
CARD”
message
No card is inserted. Turn off the power
and insert a card.
36
73
appears.
The
You have attempted Set the protect
“PROTECTED” to erase data that is setting for the data to
Misc. message
protected from
OFF.
appears and
accidental erasure.
the data cannot
be erased.
The audio
guide does not setting is set to
sound. “OFF”.
The audio guide
Set the audio guide
setting to “ON”.
107,
109
161 English
DOCKING STATION
Refer-
ence
Problem
Cause
Action
page
The remote The remote control
Aim the remote
control unit
does not
seem to
work.
unit is aimed at the TV control unit at the
(not at the docking
station).
remote control sensor
on the docking station
(within a range of
about 30 degrees
horizontally from the
docking station).
Something is
Remove or move the
obstructing the space obstructing object.
between the remote
control unit and the
remote control sensor
on the docking station.
132 −
136
Remote
control
unit
The remote control
unit battery is
consumed.
Replace with a new
battery.
The remote control
unit battery is not
correctly inserted.
Take care that the (+)
and (–) poles are
correctly oriented.
The remote control
Operate the remote
unit is too far from the control unit from a
remote control sensor position up to 7
on the docking station. meters from the
docking station.
The remote control
Change the remote
codes for the remote control code.
control unit and the
docking station are
136
different.
English 162
SPECIFICATIONS
Camera
Type
Digital movie (recording and playback)
Recorded image file Still images: JPEG format
format
(DCF, DPOF, Exif 2.2 compliant)
Note: Designed mainly by the Japan Electronics and
Information Technology Industries Association
(JEITA), DCF (Design rules for camera file
system) is standard for digital still camera
image files to provide interoperability between
digital photography devices for the images
stored on removable memory cards. However,
it is not guaranteed that all devices will support
the DCF standard.
Video clips:Conforms to ISO-standard MPEG-4
format
Audio: MPEG-4 audio (AAC compression)
48 kHz sampling rate, 16-bit stereo format
Data storage media SD Memory Card
Camera effective
number of pixels
Approx. 3,200,000 pixels
Image sensor
1/2.7-inch CCD
Virtual number of pixels: Approx. 3,340,000
pixels, interlace scan, primary color filter
Recording resolution 2,048 x 1,536 pixels (still images only)
1,600 x 1,200 pixels (still images only)
640 x 480 pixels
320 x 240 pixels (video clips only)
176 x 144 pixels (video clips only)
Video clip frame rate 30 fps, 15 fps
163 English
Data compression
(video clips only)
: : 640 x 480 pixels, 30 fps: 3 Mbps
8 : 640 x 480 pixels, 30 fps: 2 Mbps
9 : 320 x 240 pixels, 30 fps: 640 kbps
< : 320 x 240 pixels, 15 fps: 384 kbps
= : 176 x 144 pixels, 15 fps: 256 kbps
* The 30 fps frame rate of this camera is 29.97 fps,
and the 15 fps frame rate is 29.97/2.
White balance
Lens
Full-auto TTL, manual setting possible
Optical 5.8x
zoom lens
f=5.8 mm to 33.8 mm
(35 mm film camera conversion
f=38 mm to 220 mm)
Autofocus, 8 groups, 11 elements
(including two with three aspheric
surfaces)
Galvanometer iris
Internal ND filter
Aperture
Open F=3.5 (Wide) to 3.7 (Tele)
Smallest F=8.0 (Wide) to 8.4 (Tele)
Exposure control
type
Programmable AE
Exposure correction available from the Shooting
Setting Screen (0 1.8EV in 0.3EV steps)
Light-measuring
mode
Multi-section measuring
Range
Total mode:
10 cm to infinity (Wide end)
80 cm to infinity (Tele end)
Normal mode:
80 cm to infinity
Super Macro mode:
2 cm to 60 cm (Wide end only)
Digital zoom
For shooting:
1x to approx. 10x
For playback:
1x to 32x (varies with resolution)
English 164
SPECIFICATIONS
Shutter Speed
Still image shooting mode: 1/2 to 1/2,000 sec.
(During flash: 1/30 to 1/60 sec.)
Video clip shooting mode: 1/30 to 1/10,000 sec.
Sensitivity
Still image shooting mode:
Auto (equivalent to ISO50 to 200)/equivalent to
ISO50, ISO100, ISO200, and ISO400
(switchable from Shooting Setting Screen)
(Maximum ISO sensitivity up to 1600 variation:
when scene select function is set to lamp Q)
Video clip shooting mode:
Auto (equivalent to ISO200 to 800)/equivalent to
ISO200, ISO400, ISO800, and ISO1600
(switchable from Shooting Setting Screen)
LCD monitor
1.5-inch low-temperature polysilicon TFT color liquid
crystal display, translucent
Approx. 110,000 pixels
(Frame coverage: Approx. 100% when the AV
cable is not connected)
Flash working range GN = 3
Approx. 10 cm to 1.2 m (Wide)
Approx. 80 cm to 1.1 m (Tele)
Flash modes
Focus
Auto-flash, forced flash, flash off
TTL-type AF
Self-timer
Time/date
2-second delay, 10-second delay
Recorded with image data
Ambient
environment
Temperature 0 to 40°C (operation),
–20 to 60°C (storage)
Humidity
30 to 90% (operating, no
condensation)
10 to 90% (storage, no condensation)
Power supply
Battery pack Li-ion battery pack (DB-L20) x 1
Dimensions (excluding protrusions) 69 (W) x 108 (H) x 34 (D) mm
(Maximum dimensions)
Volume: Approx. 149 cc
Weight
Approx. 155 g (Only the camera
(without battery pack and card))
165 English
Camera connectors
DIGITAL/AV
Regrouped jack
(communication/
sound and image
output) terminal
Audio output 265 mVrms (–9 dBs), 12 kΩ or less,
stereo
Video output 1.0 Vp-p, 75 Ω unbalanced, sync
negative, composite video, NTSC
color TV system/PAL TV system
(switchable from the Option Setting
Screen)
USB
USB 2.0 (Full speed)
DC IN (external DC
DC 4.7 V (for exclusive use with the supplied AC
power input) terminal adapter/charger)
Battery pack operation
Shooting
Video clip recording mode 60 minutes:
Recorded in TV-S mode (320x240 pixels, 30
fps)
Still image shooting mode 160 images:
LCD monitor on, images captured at 20-second
intervals, and flash used 1 in 3 times
Playback
130 minutes:
LCD monitor on, continuous playback
e Until battery pack runs out when using a fully charged battery pack at a 20°C
ambient temperature.
e The operation time may vary depending on the conditions of the battery pack
and the conditions of use. Especially when used at temperatures below
10°C, the battery pack operation time is drastically reduced.
English 166
SPECIFICATIONS
Possible No. of Images/Possible Shooting
Time/Possible Recording Time
The table shows the possible number of images, the possible shooting time,
and the possible recording time for the supplied 128MB SD Memory Card, and
for the commercially available 512MB/16MB SD Memory Card.
Shooting/
recording
mode
Reso-
lution
SD Memory Card
512 MB
128MB
16 MB
14 images
22 images
112 images
35 sec.
setting
Y
Z
[
:
8
9
<
=
122 images
491 images
Still image
mode
195 images
785 images
978 images
3,920 images
21 min. 2 sec.
30 min. 39 sec.
1 hr. 21 min.
2 hr. 3 min.
5 min. 14 sec.
7 min. 37 sec.
20 min. 10 sec.
29 min. 11 sec.
37 min. 36 sec.
52 sec.
Video clip
mode
2 min. 18 sec.
3 min. 31 sec.
4 min. 36 sec.
2 hr. 42 min.
Sound
recording
mode
—
2 hr. 9 min.
8 hr. 40 min.
14 min. 27 sec.
e Even with cards of the same capacity, the amount of data that can actually
be stored may differ depending on the card brand, etc.
e The continuous shooting time for each video clip will differ depending, for
example, on the card capacity, environmental conditions (temperature and
shooting conditions, etc.).
167 English
Docking station
Part number
PDS-C1
Power supply
DC 4.7 V
Rated output
DC 4.2 V/4.7 V
Compatible batteries
Supplied or separately sold Li-ion battery pack
(DB-L20)
Ambient
Temperature 0 to 40°C (recharge), –20 to 60°C (storage)
environment
Humidity
10 to 85% (no condensation)
94 (W) x 35.5 (H) x 94 (D) mm
Weight (without power cord) Approx. 74 g
AC 125 V, 3 A
Dimensions
Weight
Power cord rated value
e When using the supplied AC adapter/charger abroad, the power cord may
need to be replaced in accordance with local requirements. Please contact
your local dealer for details.
Remote control unit
Part number
Power supply
Dimensions
Weight
BRC-C1
Lithium battery (CR2025)
35 (W) x 56.6 (H) x 6.5 (D) mm
Approx. 15 g (including battery)
English 168
SPECIFICATIONS
Supplied AC adapter/charger
Part number
VAR-AL20
Power supply
AC 100 V to 240 V, 50/60 Hz, 0.27 A to 0.17 A,
23 VA to 32 VA
Rated output
DC 4.2 V, 0.6 A (charging)
DC 4.7 V, 2.0 A (DC output)
Compatible battery
Supplied or sold separately Li-ion battery pack
DB-L20
Ambient
Temperature 0 to 40°C (operation), –20 to 60°C (storage)
environment
Humidity
20 to 80% (no condensation)
60 (W) x 33 (H) x 90 (D) mm
Approx. 175 g
Dimensions
Weight
Supplied Li-ion battery pack
Part number
DB-L20
Voltage
3.7 V
Rated output
720 mAh
Ambient
environment
Temperature 0 to 40°C (during use, recharged)
–10 to 30°C (storage)
Humidity
10 to 90% (no condensation)
39.4 (W) x 6.0 (H) x 35.5 (D) mm
Approx. 19 g
Dimensions
Weight
169 English
Supplied SD Memory Card
Memory capacity
128MB
Ambient
Temperature 0 to 55°C
environment
Humidity
20 to 85%
Dimensions
Weight
32 (H) x 24 (W) x 2.1 (D) mm
Approx. 2 g
English 170
SPECIFICATIONS
Others
Apple, Macintosh and QuickTime are trademarks or registered trademarks of
Apple Computer Inc.
Windows and Windows NT are registered trademarks of Microsoft Corporation.
All other company and product names are registered trademarks or trademarks
of their respective owners.
Caution
e It is forbidden to copy this manual, whole or in part, without prior written per-
mission.
e All images and illustrations given in this manual are for explanation purposes
and may differ slightly from that of the actual product. Also, actual specifica-
tions are subject to change without prior notice and therefore may differ from
the contents of this manual.
e Sanyo Electric shall not be held responsible for any problems resulting from
the use of this camera.
e Sanyo Electric declines all responsibility for damages due to improper use of
the camera, failure to adhere to the instructions given in this manual, or
repairs or changes done by those other than a technician authorized by the
manufacturer.
e Sanyo Electric shall not be held responsible for any damage caused by
optional devices or consumable items used with the camera other than those
supplied with the camera or those specified by Sanyo Electric.
e Sanyo Electric shall not be held responsible for any losses or loss of revenue
resulting from the loss of data caused by the malfunction, or the repairing of
a malfunction, of the camera.
e The images captured with this camera will differ in quality from pictures taken
with a standard film camera.
171 English
MEMO
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Printed on recycled paper
SANYO Electric Co., Ltd.
Printed in Japan
1AG6P1P1704--
SX613/EX, U (1003KP-SY)
|