Samsung SHC 750 User Manual

Ultimate  
Sensitivity  
Extreme Low Light Camera SHC-750 User’s Manual  
SALES NETWORK  
SAMSUNG TECHWIN CO., LTD.  
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,  
Gyeonggi-do 462-703, Korea  
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.  
7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China  
TEL : +86-22-2761-4724(33821) FAX : +86-22-2761-6514  
Thank you for purchasing a SAMSUNG CCD CAMERA.  
Before attempting to connect or operate this product,  
please read these instructions carefully and save this manual for future use.  
TEL : +82-31-740-8137~8139 FAX : +82-31-740-8145  
SAMSUNG OPTO-ELECTRONICS UK, LTD.  
Samsung House, 1000 Hillswood Drive, Hillswood Business  
Park Chertsey, Surrey KT16 OPS  
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325  
P/No. : Z6806-0762-01B  
VAN 06. 09  
ENGLISH  
The lightning flash with an arrowhead symbol, within an equilateral triangle is  
intended to alert the user to the presence of uninsulated dangerous voltage”  
within the product's enclosure that may be of sufficient magnitude to  
constitute a risk of electric shock to persons.  
The exclamation point within an equilateral triangle is intended to alert the user  
to the presence of important operating and maintenance (servicing)  
instructions in the literature accompanying the appliance.  
INFORMATION-This equipment has been tested and found to comply with limits  
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause harmful interference to radio  
communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference at  
his own expense.  
WARNING - Changes or modifications not expressly approved by the manufacturer  
could void the user’s authority to operate the equipment.  
CAUTION : To prevent electric shock and risk of fire hazards:  
Do NOT use power sources other than that specified.  
Do NOT expose this appliance to rain or moisture.  
This installation should be made by a qualified service person and  
should conform to all local codes.  
Samsung Techwin cares for the environment at all product manufacturing  
stages to preserve the environment, and is taking a number of steps to  
provide customers with more environment-friendly products.The Eco mark  
represents Samsung Techwin s will to create environment-friendly products,  
and indicates that the product satisfies the EU RoHS Directive.  
M ajo r Func tio ns and Features  
EMCCD for Extreme Light  
Motion Detection  
Sensitivity  
A 1/2 inch Electron Multiplying Charge  
Coupled Device (EMCCD) and advanced  
digital signal processing technology are  
employed to produce sharper shapes and  
colors in the subject image, even under  
ultra low light conditions. This is suitable  
for 24-hour outdoor surveillance where  
available light levels can get extremely low.  
-Color: 0.008Lux (F1.2, EIAJ)  
The product’s Motion Detection feature detects  
moving subjects and generates a signal  
accordingly. An alarm device may be connected  
directly (i.e. with no external sensor) to the  
product for more effective security.  
Warning s & Cautio ns  
This information is provided to ensure your safety and to prevent any losses, financial or  
otherwise. Please read it carefully and use the product accordingly.  
Video-Drive/DC-Drive Lens  
Support  
Warning/Attention/Special Mark Messages  
Video-drive lens or DC-drive lens selection  
is by a simple switch control. The  
-B/W: 0.0005Lux (F1.2, EIAJ)  
brightness of the video lens can be  
adjusted without fine VR adjustments.  
Ignoring this information may result in material loss and/or serious  
personal injuries including death.  
Samsung Super Noise Reduction  
(SSNR)  
SHC-750 DSP  
Indicates Never Allowed.”  
Samsung original SSNR technology effectively  
eliminates low light noise, increases horizontal  
resolution, and improves the S/N ratio.  
The resulting image is clear and vivid even in  
low light conditions.  
The high performance DSP capability of the  
SHC-750 effectively eliminates low light  
noise and produces not only clearer images  
but also sharper colors. The resulting  
image is vivid and precise.  
Indicates No Disassembling.”  
Indicates Must Observe.  
On-Screen Text Display & RS-485  
Communication Technology  
Camera functions may be controlled using  
the on-screen text displays.  
RS-485 communication technology enables  
long-distance remote control of the camera  
functions.  
Day & Night  
It automatically distinguishes between day  
and night, and switches to the appropriate  
mode. Color mode is used during the day  
to produce optimum color images; B/W  
mode is used at night to deliver clearer  
images in the dark.  
Extra Features  
Extra features include Sens-Up, Privacy,  
Sharpness, Smear Cancel, and Mirror.  
Co ntents  
20  
Instructions: Camera Operation  
Precautions  
8
Menu Functions  
Function Settings  
CAMERA ID  
BACKLIGHT  
WHITE BAL  
MOTION DET  
LENS SELECTION  
SHUTTER  
20  
21  
22  
24  
26  
10  
Product Components  
11  
11  
Names and Functions of Each Part  
27  
28  
29  
30  
Front  
Bottom  
Back  
12  
13  
AUTO GAIN CONTROL  
SENS-UP  
SSNR  
30  
32  
33  
14  
14  
Instructions: Setup  
SPECIAL  
Lens  
Using Auto Iris Lenses  
Using C/CS Mount Lenses  
35  
36  
37  
Remote Control / MD Output / D&N Input  
Problems & Solutions  
18  
Instructions: Connection  
Product Specification  
Connecting a Monitor  
Connecting the Power  
18  
19  
38  
Protocol Command Description  
Prec autio ns  
Installation of this product by unqualified  
personnel is strictly prohibited.  
If the camera overheats or smoke is  
noticed, turn the power off immediately.  
Do not expose the product to extreme  
heat or cold.  
Do not use the product in areas where the  
illumination levels fluctuate frequently.  
Experience and technical know-how are required  
for proper installation, and to prevent possible fire  
or electric shock. Please consult an authorized  
retailer for any installation questions.  
It may cause fire.  
Do not expose the product to extreme heat or cold. Temperatures outside  
its operating temperature range (-10˚C(14˚F) ~ 50˚C(122˚F)) may reduce  
image quality or cause product malfunction. Pay special attention to  
ventilation around the product in warm locations.  
Fluctuating light levels caused by an unstable  
fluorescent lamp, for example, may cause product  
malfunction.  
Do not install the product in an area of high humidity  
or near flammable materials (e.g. oil or gas).  
Do not install the product unless the location  
can fully support the products weight.  
Do not drop, shake, or apply severe  
impact to the product.  
Do not point the camera towards a  
strong light source such as the sun.  
Using the product in an incorrect environment may  
cause fire, electric shock, or damage to the product.  
If it is not properly supported, the product may fall.  
It may damage the product.  
Excessive light may cause fatal damage to the CCD.  
Do not handle power plugs with  
wet hands.  
Do not insert foreign objects into the  
product or disassemble the product.  
Do not touch the glass on the front of  
the camera.  
Do not expose the product to rain or water,  
or place it near radioactive materials.  
It may cause electric shock.  
It may cause fire or damage the product.  
This is the most important part of the camera. Be careful  
not to leave any marks, including fingerprints, on the glass.  
Water inside the camera may cause product  
malfunction.  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
8
9
Pro d uc t Co m p o nents  
Nam es and Func tio ns o f Eac h Part  
Front  
1. 1/2 inch Ultra Low Light EM CCD  
SHC-750N Color Camera  
2. Connector Plug for Auto Iris Lens  
3. Remote Connector Plug  
4. C-mount Adapter  
Groove for Tripod Mount  
Used to secure the camera case on a tripod mount:  
loosen the screws located on the bottom of the tripod and secure the camera to it.  
C-mount Lens Adapter  
Used for mounting a C-mount lens.  
5. User Manual  
Back Focus Control Screw  
Adjusts back focus  
Auto Iris Lens Connector  
Connector port for auto iris lens  
6. DC 12V/4A Adapter  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
10  
11  
Nam es and Func tio ns o f Eac h Part  
Bottom  
Back  
Function Buttons  
Set button: For displaying the menu screen. Press to confirm selections or changes made.  
Up/Down button: For moving the screen cursor up/down to select menu items  
Left/Right button: For moving the screen cursor left/right to change selected item values  
Groove for Tripod Mount  
Used to mount the camera on a bracket or a tripod  
The size of the screws for this groove is as follows.  
L
Power Lamp  
(ISO standard)  
The lamp turns on when the power is properly connected.  
1/4"-20 UNC (20 THREAD)  
L:4.5mm±0.2mm (ISO standard),  
or 0.197" (ASA standard)  
D&N Input / MD Output Port  
For external signal input to enable Day&Night mode filter control  
For motion detection signal output to help improve security effectiveness  
Power Input Connector  
Connect the adapter provided with this product here; be sure to match the +/- of the port  
The Tripod anchor can be relocated to the top or the  
bottom. Always use the screws provided to secure the  
camera. Otherwise, mounting may not be properly  
secure or internal damage might occur.  
Remote Port  
Connect external devices here to control the 5 function-setting buttons remotely  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
12  
13  
Nam es and Func tio ns o f Eac h Part  
3. Remove the cover from the lens connector jack and solder the cable to the jack pins.  
Auto Iris Lens Selection Switch  
Set to DC or Video according to the lens in use  
Video type :  
DC type :  
No. 1 Pin --- Red (Power source)  
No. 2 Pin --- N.C  
No. 3 Pin --- White (Video signal)  
No. 4 Pin --- Black (GND)  
No. 1 Pin --- Damping -  
No. 2 Pin --- Damping +  
No. 3 Pin --- Drive +  
No. 4 Pin --- Drive -  
Video Output Port  
For video signal output; connects to a monitor video input port  
Instruc tio ns: Setup  
Lens Cable  
Connector  
Lens  
pin3  
pin1  
Lenses are sold separately. Auto iris, CS-mount, or C-mount lenses may be used.  
pin4  
pin2  
Caution  
For maximum utilization of the product’s features, we recommend the use of a  
DC-type auto iris lens.  
4. Replace the cover to the lens connector jack. Remove the front glass protector from the  
product and fit an auto iris lens by screwing the lens in clockwise.  
Any dirt or smudges including fingerprints may reduce the picture quality in low  
light conditions; please keep it clean.  
5. Insert the connector jack, now soldered to the lens cable, into the lens connector port  
located on the side of the product.  
When using an auto iris lens  
1. Strip the outer layer of the lens cable for  
about 8mm (0.3in) from the end.  
6. Set the lens selection switch located on the side either to  
DC or to Video according to the type of auto iris lens now  
in use.  
2. Strip the inner layer of the cable for about  
2mm (0.08in) from the end.  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
14  
15  
Instruc tio ns: Setup  
When using a C-mount lens  
1. Remove the front glass protector from the product and fit a C-mount adapter by screwing  
it in clockwise.  
When using a C/CS-mount lens  
Check if the lens to be mounted is the C-mount or CS-mount type. The default setting of this  
camera is for a CS-mount lens, and minor adjustments are required before a C-mount lens can  
be used.  
When using a CS-mount lens  
Remove the front glass protector from the product and fit a CS-mount lens by screwing the  
lens in clockwise.  
2. Fit a C-mount lens on the adapter by screwing it in clockwise.  
Caution  
Use lens holders that look like the pictures shown below. An incorrect fit  
between the lens and its holder may result in internal damage to the product or  
unstable installation.  
C-mount lens: 10mm or smaller  
CS-mount lens: 5mm or smaller  
Using a heavier lens may result in an imbalanced camera and/or cause product  
malfunction. Limit the lens weight to 450g (1lb) or less. To use ALC, Av mode is  
strongly recommended.  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
16  
17  
Instruc tio n: Co nnec tio n  
Connecting a Monitor  
Connecting the Power  
Connect the video output port located on the back of the product to a monitor.  
Power requirements depend on the model; please check the product model number and  
its stated power requirements.  
The power connection method is as shown below.  
Using DC Power  
Use the adapter provided with this product.  
CCD Camera  
Monitor  
The actual connection method depends on the peripherals; please refer to the manual of the  
device being connected for more details.  
• Please make sure all the power is OFF from all relevant devices before making any  
connections.  
Set the 75/ Hi-Z diverter switch of the intermediate video receiver to Hi-Z, and set the end  
unit device to 75.  
When the resistance of the copper wire is 20˚C(68˚F)  
Copper wire size(AWG) #24(0.22mm2) #22(0.33mm2) #20(0.52mm2)  
#18(0.83mm2)  
0.018  
CCD Camera  
Intermediate  
End monitor  
Resistance value(/m)  
0.078  
0.028  
0.050  
0.018  
0.030  
0.011  
Voltage drop(V/m)  
0.006  
As shown in above chart, the voltage drops depending on the length of the wire. If the  
adapter output cable is too long, therefore, it may interfere with the camera operations.  
Guaranteed operating voltage of the camera: DC12V 10%  
Actual voltage may vary from the above chart depending on the manufacturer or model.  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
18  
19  
Instruc tio n: Cam era Op eratio n  
Menu Functions  
Function Settings  
Use the 5 buttons located on the back of the product to set different functions.  
SETUP menu  
Up button  
Camera ID  
Backlight  
OFF  
ON  
Left button  
Set button  
Right button  
Down button  
BLC  
OFF  
WHITE BAL  
Motion Det  
Lens Selection  
Shutter  
ATW  
OFF  
AWC • MANUAL  
ON  
1. Press the Set button to display the Main Setup menu on the monitor.  
DC/VIDEO  
A.FLK  
OFF  
SETUP  
MANUAL  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
OFF  
OFF  
ATW  
OFF  
Auto Gain Control  
Sens-Up  
LOW • HIGH  
AUTO  
DC  
OFF  
SHUTTER  
AGC  
SENS-UP  
SSNR  
SPECIAL  
EXIT  
MANUAL  
HIGH  
OFF  
SSNR  
OFF  
LOW • MIDDLE • HIGH  
MIDDLE  
SPECIAL  
• PRIVACY  
IMAGE  
COLOR  
RESET  
SHARPNESS  
RETURN  
SMEAR CANCLE  
EXIT  
2. Press the Up/Down buttons to move the arrow up/down until the arrow is pointing to the  
item desired.  
EXIT  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
20  
21  
Instruc tio n: Cam era Op eratio n  
Caution  
SETUP  
SETUP  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
Use the Up/Down buttons to  
select an item.  
Use the Left/Right buttons to  
change the item value.  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
OFF  
OFF  
OFF  
OFF  
• If the current status is OFF,” the camera ID will not  
be displayed on a monitor even if an ID is assigned.  
ATW  
OFF  
ATW  
OFF  
DC  
SHUTTER  
AGC  
SENS-UP  
SSNR  
MANUAL  
HIGH  
OFF  
DC  
MIDDLE  
SHUTTER  
AGC  
SENS-UP  
SSNR  
MANUAL  
HIGH  
OFF  
SPECIAL  
EXIT  
MIDDLE  
SPECIAL  
EXIT  
3. Press the Set button.  
3. Use the Left/Right buttons to change the current value.  
• Pressing the Left/Right buttons will display all possible values or modes in order.  
Keep pressing the button until the desired value or mode is displayed.  
4. Select Exit and then press the Set button to exit.  
Caution  
4. A number from 0~255 may be assigned as a  
camera ID.  
Move the ID number cursor left/right to select and  
assign an ID.  
The “ ” sign indicates that there is a further menu within the current mode;  
press the Set button to move to the menu following.  
The - - - ” sign indicates that the current mode cannot be used.  
Camera ID  
5. Once the ID is assigned, select a position for ID  
display.  
If an ID is assigned to a camera, it can be displayed on a monitor and that camera’s  
communication mode can be changed when communicating with external devices.  
Press the Set button from the Position menu.  
1. After the Setup menu is displayed on the monitor, press the Up/Down button to move the  
arrow until it is pointing to “Camera ID.”  
2. Press the Left/Right button until the current status changes to “ON.”  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
22  
23  
Instruc tio n: Cam era Op eratio n  
2. Press the Left/Right buttons to select the mode suitable for the camera’s purpose.  
BLC: Delivers clearer images when the subject is in strong backlight.  
OFF: Canceled  
ID will be displayed on the top left corner of  
the monitor.  
FRONT DOOR  
to Locate,, then SET  
FRONT DOOR  
Use the 4 directional buttons to select a location  
for the ID to be displayed, and then press the  
BLC  
OFF  
Set button.  
3. Press the Exit button when done.  
to Locate,, then SET  
6. Communication mode can be set for communicating  
with external devices.  
Caution  
We do not recommend the use of manual lenses.  
RTN Pack: Configure package response.  
BAUD Rate: Set the communication speed (9600/19200/38400/57600).  
The BLC function is not available when a Video lens is in use.  
7. Select END” and press the Set button when done.  
BackLight  
Unlike conventional cameras, this camera uses a unique SHC-750 DSP chip to deliver clearer  
images of both the subject and its background, even against strong backlight.  
1. After the Setup menu is displayed on the screen, press the Up/Down buttons to move the  
arrow to “BackLight.”  
SETUP  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
OFF  
OFF  
ATW  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
24  
25  
Instruc tio n: Cam era Op eratio n  
White Bal  
Motion Det  
Use the White Balance feature for screen color control.  
This product generates a signal whenever motion is detected. Connecting an alarm device to  
the product, therefore, may increase security efficiency. Motion detection signals are output  
through the MD output port.  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to  
White Bal.”  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to  
Motion Det.”  
2. Press the Left/Right buttons to select a mode.  
2. Press the Left/Right buttons to select a mode (On/Off).  
SETUP  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
OFF  
OFF  
ATW  
OFF  
SETUP  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
OFF  
OFF  
ATW  
OFF  
DC  
Choose from the three modes shown below  
ATW : One of the two modes below can be selected  
Normal - Use when the color temperature is between 1800~10500K  
Special - Use when the color temperature is between 1600~10500K  
3. Press the Exit button to save the settings and exit.  
AWC : To find the optimum setting for the current illumination, point the camera at a  
piece of white paper and then press the Set button. Repeat the process when  
the illumination changes.  
Caution  
Perform a lengthy test after setting MD, to confirm everything is operating properly.  
Manual: Manual control allows finer adjustments. Set the camera to ATW or AWC  
mode first, and then change to Manual mode. Press the Set button. Decide on  
the proper color temperature, and then adjust the values of Red and Blue while  
observing the color changes of the subject on the screen.  
Use of the MD feature is not recommended if the camera is subject to direct  
fluorescent light or extreme fluctuations of light; malfunction may occur.  
Sudden changes in subject illumination due to flashlights or fluorescent lighting  
being turned on/off may cause malfunction.  
Other automatic algorithm execution speeds may slow down when the motion  
detection feature is active.  
Caution  
The White Balance may not function properly under the following conditions.  
This feature is NOT suitable for fires, burglary, or  
other similar security purposes. The manufacturer  
will not be responsible for any accidents or loss that  
may occur under these circumstances.  
• If the subject’s environment has very high color temperatures (e.g. clear sky or  
sunset).  
• If the subject is in a dark environment  
The MD output port located on the back of the  
product can be connected to external alarm devices.  
• If the camera is directly facing a fluorescent light, or if it is subject to extreme  
fluctuations of light, the White Balance function may become unstable.  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
26  
27  
Instruc tio n: Cam era Op eratio n  
Caution  
Lens Selection  
• If an auto iris lens is used, the lens selection switch on the side of the product  
must be set either to DC or to Video accordingly. (See picture on p.15)  
This feature controls the brightness of the screen.  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to “Lens.”  
2. The lens selected with the Auto Iris lens selection switch will be displayed. (See picture on p.13)  
The brightness may be adjusted if a DC/Video lens is used; the adjustment range  
is 1~100. Adjust to the optimum screen brightness.  
Some lenses may not work correctly in certain brightness levels.  
SETUP  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
OFF  
3. Press the Set button to go back to the previous menu.  
OFF  
ATW  
OFF  
Shutter  
DC  
SHUTTER  
MANUAL  
Select either auto or manual shutter control  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to “Shutter.”  
DC/Video: Used to choose DC or VIDEO according to the type of Auto Iris Lens.  
2. Press the Left/Right buttons to select a Shutter mode.  
A.FLK : Select this mode if screen flickering occurs due to a conflict between the  
illumination and the frequency  
Caution  
Manual : Select this mode for manual shutter control  
When using a Video type auto iris lens  
Properly adjust the ALC control port on the lens: the usual setting is Av.  
SETUP  
Depending on the lens type being used, it may not operate properly in AV  
mode. If the lens does not adjust correctly, set  
it to PEAK and adjust it by turning the LEVEL  
adjustment lever in the L” direction little by  
little, away from the middle position.  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
OFF  
OFF  
ATW  
OFF  
DC  
If the right level of light cannot be obtained, or  
if the screen’s brightness fluctuates, place the  
cursor on Video Level Search and press the  
Set button. Press End when you find the right brightness.  
SHUTTER  
AGC  
SENS-UP  
MANUAL  
HIGH  
OFF  
If the right level of light cannot be obtained and the lens is still fluctuating,  
3. Manual mode enables manual shutter control  
point the camera towards a darker area and repeat step  
.
The shutter speed can be from 1/60 sec. to 1/2000 sec. (x2~x128 Sens-up can be  
operated manually.)  
To control the brightness, increase/decrease the Brightness value.  
To control the diaphragm, increase/decrease the V-Level value.  
4. Press the Set button when done.  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
28  
29  
Instruc tio n: Cam era Op eratio n  
Auto Gain Control  
SETUP  
CAMERA ID  
BACKLIGHT  
OFF  
OFF  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to “AGC.”  
2. Press the Left/Right buttons to select a mode. As the Gain level increases, the screen  
becomes brighter and noise level increases.  
WHITE BAL.  
MOTION DET.  
LENS  
ATW  
OFF  
High : Gain automatically changes from 0 up to the maximum of 60dB.  
Low : Gain automatically changes from 0 up to the maximum of 54dB.  
Off : Off  
DC  
SHUTTER  
AGC  
MANUAL  
HIGH  
OFF  
SENS-UP  
SSNR  
SPECIAL  
EXIT  
SETUP  
MIDDLE  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
OFF  
OFF  
ATW  
OFF  
DC  
3. Press the Set button when done.  
Caution  
SHUTTER  
AGC  
SENS-UP  
SSNR  
MANUAL  
HIGH  
OFF  
Press the Setup button from the Auto menu to adjust the Sens-Up rate  
(x2~x128).  
MIDDLE  
SPECIAL  
EXIT  
As the rate increases, the screen gets brighter but the ghost image gets larger as well.  
Shutter is not available when Auto mode is selected.  
Sens-Up  
Automatically detects the level of darkness (e.g. at night or under low illumination) and makes  
adjustments to keep the screen bright and clear.  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to  
Sens-Up.”  
2. Press the Left/Right buttons to select a mode.  
Auto : Automatic Sens-Up mode is selected.  
Off : Off  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
30  
31  
Instruc tio n: Cam era Op eratio n  
SSNR  
Special  
Low light noise is reduced in different ways depending on the mode; the noise reduction level  
changes from none to maximum as the mode changes from Off to Low, Middle, and High.  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to “SSNR.”  
SETUP  
CAMERA ID  
BACKLIGHT  
WHITE BAL.  
MOTION DET.  
LENS  
OFF  
OFF  
1. After the Setup menu is displayed, press the Up/Down buttons to move the arrow to  
Special.”  
2. Press the Left/Right buttons to select a mode.  
Privacy : Masks selected areas from the screen  
- Off : Off  
- On : Privacy mode is currently On  
Press the Set button  
Select an area to mask from the 4 areas in Area Sel  
Change the Area State of the selected area to On  
From Area Tone, press the Left/Right buttons to control the brightness  
Set the area size from the Top/Down/Left/Right menu, and then press the Set button.  
ATW  
OFF  
DC  
SHUTTER  
AGC  
MANUAL  
HIGH  
OFF  
SENS-UP  
SSNR  
SPECIAL  
EXIT  
MIDDLE  
2. Press the Left/Right buttons to select a mode.  
Off : No noise reduction  
Low : Low noise reduction with almost no ghost image  
Middle : Probably the most practical mode, with enough noise reduction and not too  
much ghost image  
High : Maximum noise reduction, but the ghost image increases as well  
Color : Select Color or B/W mode  
- On : Always provide color images  
- Off : Always provide images in B/W If you press ‘SET’, a menu will appear in which  
you can turn the BURST signal ON/OFF.  
Caution  
When AGC is Off, the SSNR & Sens-Up features are not available.  
By adjusting ON/OFF, you can maintain or eliminate the BURST signal.  
- Auto : Use color and switch to B/W only when illumination level gets very low  
- Exit : The filter can be changed by signals from external devices.  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
32  
33  
Instruc tio n: Cam era Op eratio n  
Remote Control / MD Output / D&N Input  
To Remotely Control Function Buttons: Connect a remote jack to the Remote port located  
on the back of the product and wire it as shown below. External device (e.g. computer)  
buttons may act identically to the camera buttons, and perform the same functions.  
Caution  
When using a video auto iris lens and if the lens level is set to low, automatic  
switching between Color mode and B/W mode may not work properly.  
When the Gain menu is Off, the Color/B&W auto switch feature is not available.  
When the Gain menu is Off, only Color/B&W/Ext may be selected from the  
Day/Night menu.  
When switching between Color and B&W, the OSD key will be disabled for about  
3 seconds for safer operation of the product.  
TX (Data transmission)  
GND (Connection port)  
RX (Data reception)  
When infrared light is used, camera focus may not be as good as when using  
other light sources.  
1. RS-485C Communication setting  
Mode : Serial  
Data Bit : 8  
Bit/sec : 9600bps  
Image : Image may be reversed horizontally or vertically  
- HRev: Reverse the image horizontally  
Stop Bit : 1  
Parity : None  
- VRev: Reverse the image vertically  
2. Setup Menu control  
- HVRev: Reverse the image both horizontally and vertically  
Sharpness : Values are 0~31. The lower the value, the more vivid and sharp the image.  
If the Sharpness level is too low, the image may look unnatural or noise may  
occur.  
3. Motion Detection signal output level (10mA or lower)  
+4.0V~+5.0V  
When motion is detected  
Smear Cancel : DGain values are 0~100. As this value decreases, the smear gets stronger  
and sharper, and vice versa. Too high a level may distort the image.  
0V  
When no motion is detected  
5±0.5sec  
4. D&N Input  
In order to control a D&N filter using external signals (Ext mode), the system must satisfy  
the following criteria.  
Day mode : D&N port must NOT be located near the external signal port (GND port).  
Night mode : D&N port must be connected to the GND port.  
Caution  
Reset : Resets all settings back to the manufacturer’s defaults.  
Return : Saves the special menu and moves to the Setup menu.  
Exit : Saves the menu settings and exits the program.  
Please turn the power OFF before plugging/unplugging the remote jack.  
Do not connect any unnecessary pins (i.e. pins not in use)  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
34  
35  
Pro b lem s & So lutio ns  
Pro d uc t Sp ec ific atio n  
If you suspect a product malfunction, please check the suggestions below. If the problem  
persists, consult the authorized retailer where this product was purchased.  
NTSC (SHC-750N)  
PAL (SHC-750P)  
POWER  
DC 12V ( 10%) / 16.8W  
Total Pixels  
680(H) x 500(V)  
658(H) x 496(V)  
1/2" inch TI EM-CCD  
2:1 Interlace  
Problem  
Screen is blank.  
Solution  
C
C
D
Effective Pixels  
Size  
Check if the power is connected and flowing properly.  
Check if the video cables are connected properly.  
If you are using a Video (DC) lens, check if the Auto Iris lens  
switch is on DC (Video). It must be on Video (DC).  
Are you using a Video Auto Iris Lens?  
Scanning System  
Synchronization  
Frequency  
S
y
Internal  
n
Horizontal : 15.734  
Vertical : 59.94  
Horizontal : 15.625  
c.  
Readjust the Lens VR. (See p. 28)  
Vertical : 50.00  
Resolution  
420TV Lines : Color, 480 TV Lines : B/W  
Screen is not clear.  
Is the lens clean? Wipe the lens with a clean cloth or brush.  
Adjust the monitor settings.  
Video Output  
1.0Vp-p/75  
1.0Vp-p/75Ω  
If a bright light shows up on the screen, change the location or  
tilt of the camera.  
Readjust the camera’s Back Focus.  
Adjust the monitor settings.  
Check if the connections between the networked computer  
terminals are working correctly.  
(Video 0.714Vp-p, Sync 0.286Vp-p)  
(Video 0.7Vp-p, Sync 0.3Vp-p)  
S/N (Y signal)  
Min. Illumination  
Day & Night  
50dB (AGC Off, Weight ON)  
Color : 0.008 Lux(F1.2,50 IRE) B/W : 0.0005 Lux, 0.000003 Lux (Sens-up 128X)  
BW/COLOR/AUTO(Filter Auto Change)/EXT  
(External Day/Night mode control capability via terminal at the back panel)  
Low, High, OFF Selectable  
E
L
E
C
T
R
I
C
A
L
Gain Control  
BLC  
Screen is too dark.  
Are you using an Auto Iris lens? Adjust the brightness to the  
proper level.  
Back Light Compensation  
White Balance  
Electronic  
ATW/AWC/Manual (1800˚K ~10,500˚K)  
Camera is behaving oddly.  
Camera surface is too hot and screen has black lines.  
Is the power supply to the camera within the acceptable range?  
Does the voltage fluctuate frequently?  
AUTO/MANUAL  
AUTO/MANUAL  
shutter speed  
Sens-Up  
(1/60 ~ 1/2,000sec)  
(1/50 ~ 1/2,000sec)  
ON/OFF(selectable limit ~ X128)  
I cannot select Auto mode in Is the Color set to “Ext/On/Off?  
Color; Auto mode in Color is Is the Gain set to “Off?  
O.S.D  
Built-in  
ON/OFF(Built-in Alarm output connector)  
Built-in  
Motion Detection  
RS-232C  
not functioning.  
Is the Video lens level too low?  
Motion Detection feature is Is the Motion Det set to “Off?  
SSNR  
Low, Middle, High, OFF Selectable  
ON/OFF(4 Programmable Zone)  
DC / Video  
not working.  
Color is off.  
Is the MD level too low?  
Is the MD Area setting correct?  
Privacy Function  
IRIS Control  
Lens Mount  
CS Mount (C-Mount is mountable by using adaptor)  
75(W) x 65(H) x 143(D)mm  
-10˚C ~ +50˚C(14˚F ~122˚F)  
MAX ~ 90% RH  
Is the camera facing the sun or a fluorescent light?  
Is an Auto Iris lens being used? Check the connection between  
the lens connector and the cable.  
Dimension  
Operating temperature  
Operating Humidity  
Weight  
"FAN DO NOT WORK" is  
flashing on the screen.  
Check if the Fan is working. Change the Fan if it is not working.  
600g  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
36  
37  
Pro to c o l Co m m and Desc rip tio n  
Byte1  
Byte2  
Byte3  
Byte4 || Byte5  
Byte6  
Byte7  
Byte8  
Byte9  
Byte10  
Byte11  
Command Name  
Function  
Command Packet  
Return Packet  
Function  
STX  
STX  
CAM ID  
CAM ID  
HOST ADDR  
HOST ADDR  
Command  
Response  
Data3  
Data3  
Data4  
Data4  
Data5  
Data5  
Data6  
Data6  
ETX  
ETX  
CHECK SUM  
CHECK SUM  
Display OSD menu on the screen.  
OSD Menu On/Off  
Clear OSD menu and save current menu setup.  
Command Packet  
Return Packet  
Parameter  
A0h  
A0h  
CAM ID  
CAM ID  
HOST ADDR  
HOST ADDR  
00B1h  
00B1h  
P1  
P1  
00h  
00h  
00h  
00h  
00h  
00h  
AFh  
AFh  
CHECK SUM  
CHECK SUM  
P1: 00h = ON  
01h = OFF  
Function  
Move OSD arrow to up.  
OSD Menu Up  
Command Packet  
Return Packet  
Function  
A0h  
A0h  
CAM ID  
CAM ID  
HOST ADDR  
HOST ADDR  
0008h  
0008h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
AFh  
AFh  
CHECK SUM  
CHECK SUM  
Move OSD arrow to down.  
OSD Menu Down  
OSD Menu Left  
OSD Menu Right  
Command Packet  
Return Packet  
Function  
A0h  
A0h  
CAM ID  
CAM ID  
HOST ADDR  
HOST ADDR  
0010h  
0010h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
AFh  
AFh  
CHECK SUM  
CHECK SUM  
Move OSD arrow to left.  
Command Packet  
Return Packet  
Function  
A0h  
A0h  
CAM ID  
CAM ID  
HOST ADDR  
HOST ADDR  
0004h  
0004h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
AFh  
AFh  
CHECK SUM  
CHECK SUM  
Move OSD arrow to right.  
Command Packet  
Return Packet  
A0h  
A0h  
CAM ID  
CAM ID  
HOST ADDR  
HOST ADDR  
0002h  
0002h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
00h  
AFh  
AFh  
CHECK SUM  
CHECK SUM  
COLOR CCD CAMERA  
Users Manual  
COLOR CCD CAMERA  
Users Manual  
38  
39  
DECLARATION OF CONFORMITY  
M E M O  
Application of Council Directive(s)  
89 / 336 / EEC  
Manufacturer's Name  
Manufacturer's Address  
SAMSUNG TECHWIN CO., LTD  
SAMSUNG TECHWIN CO., LTD  
42, SUNGJU-DONG CHANGWON-CITY,  
KYUNGNAM, KOREA, 641-120  
European Representative Name  
European Representative Address  
Equipment Type/Environment  
Model Name  
CCTV Camera  
SHC-750  
Beginning Serial NO.  
S6060001  
Year of Manufacture  
2006. 9. 1  
Conformance to  
EN 50081-1:1992  
EMC-Directive 89/336 EEC and 92/31/EEC  
EN 50130-4:1996  
We, the undersigned, hereby declare that the equipment specified above conforms  
to the above Directive(s).  
Manufacturer SAMSUNG TECHWIN CO., LTD  
Signature  
Legal Representative in Europe  
Signature  
Full Name  
Position  
Place  
Full Name  
Position  
Place  
YOUNG TAEK SON  
QUALITY CONTROL MANAGER  
CHANGWON, KOREA  
2006. 9. 1  
Date  
Date  
M E M O  

Welch Allyn Medical Diagnostic Equipment Car Video System REF SERIE 420 User Manual
Vivitar 840XHD User Manual
Viking DUWC!44 User Manual
Sony XR 4300R User Manual
Sony DCR SX20K User Manual
Sony Camcorder DSR PD170 User Manual
Sony Blu ray Player BDP S470 User Manual
Sharp XEA 401 User Manual
Sanyo VPC HD1000GX User Manual
Samsung EXMS60SB User Manual