400.00 mm
Audio Adaptor
+
DC Socket
PLAY/STOP
LED
AC Adaptor
Bluetooth enabled PDA
[ D ]
Bluetooth mobile phone
[ A ]
Headset
BT65N
Bluetooth Stereo Audio Adaptor (optional)
1.
!
Or alternatively, connect the USB charging cable and the Y-cable together. And
then, connect the two ends of the Y-cable to the Headset’s and the Audio Adaptor’s
DC socket. Make sure the USB charging cable is connected to the computer USB
port providing 500 mA for optimal charging results.
PBT55D
Bluetooth Stereo Headset
!
!
!
Backward
Reject the call
Voice dialing
4.
!
!
!
Forward
Call transfer
Redial the last number
Bluetooth
Stereo
Headset
2.
!
!
!
!
Power On/ Off
Play
Stop
5.
!
Audio Adaptor
LED
Pairing
3. VOL -
Volume down
6. VOL +
Volume up
!
!
DC Socket
500mA
USB Port
USB Bluetooth dongle
[ C ]
Bluetooth Audio Adaptor
[ B ]
How to open the folded headset and wear
USB Charging
Cable
1)Unfold the folded headset until they are fully extended to the opened position(see
Figure.1 and Figure.2 )
I. [ A ] Stereo Headset paired with Bluetooth mobile phone Guide
Headset
1. Pairing
!
Low-battery indication
a. While the Headset is powered off, press and hold button for 4 seconds. The
LED will flash red and green alternatively, which indicates the Headset in
Pairing Mode. The Pairing Mode will last for one minute.
b. Follow the operating instructions of your Bluetooth mobile phone to start the
pairing process. Typically, this has to be done by going to a setup or connect
menu and then selecting the options to discover Bluetooth devices. It may take
several seconds to establish a Bluetooth connection. Your phone’s display
should indicate that it has found the model name “PBT55D”; and prompt you for
a passkey or PIN. Enter a sequence of “0000”.
When the battery is low, the LED of the Headset or that of the Audio Adaptor will flash
red instead of green. When the battery level is too low, the Headset or the Audio
Adaptor will automatically power off.
!
Turning on / Turning off the Headset and the Audio Adaptor
When the Headset or the Audio Adaptor is powered off, press and hold button till
the LED flashes green, which indicates the Headset or the Audio Adaptor is powered
up. When the Headset or the Audio Adaptor is powered up, press and hold button,
the LED will keep red for a while then off, which indicates it is powered down.
Figure. 1
Figure. 2
Environmental
friendly
1
3
5
2)Rotate the earcups until they are in the locked position (see drawing Figure.3)
c. If the pairing is successful, the LED will flash green, which indicates it is in
Standby Mode and ready to answer and receive mobile phone calls from it. If
pairing does not occur as expected, turn the Headset and the mobile phone off.
Wait for 10 seconds and repeat the pairing process from the beginning.
Index
1． How to open the folded headset and wear
3. Low-battery indication .................................................................................................3
..........................................................1
2． Charging and recharging the battery
4. Turning on / Turning off the Headset and the Audio Adaptor
....................................................................2
...............................3
2. Answering incoming calls / Rejecting incoming calls
a. When an incoming call is present, a ring tone will be heard from the earpiece of
Seven possible User Scenarios ...................................................................................4
the Headset. Press PLAY button will answer the call. Press
reject the call.
button will
I.
Stereo Headset paired with Bluetooth mobile phone Guide
1. Pairing ....................................................................................................5
2. Answering incoming calls Rejecting incoming calls ................................6
3. Ending calls .......................................................................................................6
4. Last number redial ...............................................................................................6
5. Adjusting speaker volume .......................................................................6
6. Activating voice dialing ..........................................................................................6
7. Transfer call ........................ .................................................................7
[
A
]..............5
b. [Advance function] If the Headset is connected with your mobile phone and
another Bluetooth transmitter such as the Audio Adaptor simultaneously and
you are listening to the music using the earpiece, a ring tone will prompt you.
/
Press PLAY button will answer the call. Press
you will continue listening to the music.
button will reject the call and
Figure. 3
3. Ending calls
a. While a call is in session, press button will end the call.
b. [Advance function] If the Headset is connected with your mobile phone and
another Bluetooth transmitter such as the Audio Adaptor simultaneously, press
STOP button will end the call and you will continue listening to the music.
II.
Stereo Headset paired with Stereo Audio Adaptor Guide
1. Pairing .................................................................................................................7
2. Listening to music ...............................................................................................7
[
B
]
........................7
3)Wear the headset (see drawing Figure. 4) with the headband behind your head.
Adjust the position until you feel the most comfort.
III. Stereo Headset paired with USB Bluetooth Dongle Guide
1. Pairing .................................................................................................................8
2. Listening to music ...............................................................................................8
[
C
]
......................8
4. Last number redial
a. While the Headset and Bluetooth mobile are in Standby Mode, press and hold
the
button for 2 second to redial the last dialed number.
b. [Advance function] If the Headset is connected with your mobile phone and
another Bluetooth transmitter such as the Audio Adaptor, press and hold the
Button for 2 second to redial the last dialed number. Press STOP button to end
the call as normal.
IV. Stereo Headset paired with Bluetooth enabled PDA Guide
1. Pairing .................................................................................................................9
2. Listening to music ...............................................................................................9
[
D
]
....................9
V. Stereo Pendant paired with Audio Adaptor and
Bluetooth mobile phone Guide
. .
...........................................................10
5. Adjusting speaker volume
a. While a call is in session, pressing and releasing VOL + / VOL - buttons will
adjust the speaker volume.
[
A
&
B
]
1. Pairing ...............................................................................................................10
2. Listening to music .............................................................................................10
3. Monitoring mobile phone calls ............................................................................10
b. [Advance function] While the Headset is playing music, pressing / releasing
VOL+ / VOL - buttons will adjust the speaker volume.
VI. Stereo Headset paired with USB
Bluetooth dongle and Bluetooth mobile phone Guide [ A &
.
........................11
C
]
6. Activating voice dialing
1. Pairing ...............................................................................................................11
2. Listening to music ..............................................................................................11
3. Monitoring mobile phone calls ...........................................................................11
When the Headset is in standby mode, press and hold the button
for 2
seconds until a long beep is heard. The Headset is connecting to your mobile
phone for voice dialing function. If the connection is successfully made, the
phone will ask for the name of the person you wish to call. The call will be
executed in a few seconds. If the connection is failed, the Headset will beep
and go back to standby mode. Before the Headset entering into voice dialing
mode, make sure the voice dialing function of the phone is enabled.
VII. Stereo Headset paired with
.
Bluetooth enabled PDA and Bluetooth mobile phone Guide [ A & D ] ...............12
1. Pairing ...............................................................................................................12
2. Listening to music .............................................................................................12
3. Monitoring mobile phone calls ...........................................................................12
Figure. 4
!
Charging and recharging the battery
(ADVANCE FUNCTION) While the Headset is playing the music, continuously
pressing the button
Thank you for buying the new PBT55D Bluetooth Stereo Headset and the new
BT65N Bluetooth Stereo Audio Adaptor pack. Before first time use, it is important to
charge the battery of each of them for 6 hours. During recharging, the LED shows a
steady red light. When the battery is fully charged, the Red LED is off.
Accessories Table ................................................................................................12
will stop the music playing and a long beep will be heard,
indicating that the Headset is connecting with mobile phone for voice dialing function.
If the connection is successfully made, the voice dialing can be executed according to
the mobile phone’s menu operations. ( If the connection is failed, the Headset will beep
and go back to music playing.)
FCC Interference Statement ..................................................................................13
Declaration of Conformity ......................................................................................14
Remarks: Voice dialing function is not supported in Sony Ericsson K750i
6
2
4
|