ADDENDUM
Addendum No. C3409M
Date December 22, 2005
Manuals Affected C2462M-B, C2403M-C, C2410M-H,
C2491M-B, C2496M
Manual Update Switch Settings for Varifocal Lens
Manual Update The high resolution camera with vari-
focal lens and auto iris is configured at
the factory for automatic exposure.
SWITCH SETTINGS FOR VARIFOCAL LENS
The high resolution camera with varifocal lens and auto iris is configured at the factory for
automatic exposure.
1
2
3
4
5
6
7
8
AWB Automatic white balance
GAM Gamma function
FACTORY SETTINGS
1
2
3
4
5
6
7
8
AGC
ESC
BLC
Automatic gain control
Electronic shutter control
Backlight compensation
Flickerless
ON
OFF
OFF
= SWITCH POSITION
FL
AE
Automatic exposure
Not used
Figure 1. Switch Settings for Varifocal Lens
Pelco Worldwide Headquarters
3500 Pelco Way • Clovis, California 93612 USA
USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150
International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120
CONTENTS
Section
Page
IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................ 3
REGULATORY NOTICES ............................................................................................................................... 3
DESCRIPTION .............................................................................................................................................. 4
INSTALLATION ............................................................................................................................................. 4
INSTALL BACK BOX ........................................................................................................................... 4
MOUNTING DIRECTLY TO WALL OR CEILING ........................................................................ 4
MOUNTING TO 4S DEEP ELECTRICAL BOX ............................................................................ 5
MOUNTING TO CEILING TILE .................................................................................................. 5
INSTALL CAMERA ............................................................................................................................. 5
INSTALL DOME AND TRIM RING ..................................................................................................... 7
ADJUSTMENTS (COLOR CAMERA ONLY) .................................................................................................. 7
VERTICAL PHASE (24 VAC OPERATION ONLY) ................................................................................. 7
AUTO IRIS LEVEL ADJUSTMENT ...................................................................................................... 8
FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS .................................... 8
SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS ......................................... 9
SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS .................................. 9
SWITCH SETTINGS FOR VARIFOCAL LENS ..................................................................................... 10
SPECIFICATIONS .......................................................................................................................................... 11
[ 2 ] Pelco Manual C2410M-H (10/05)
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (in-
cluding amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or ob-
jects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
10. Installation should be done only by qualified personnel and conform to all local codes.
11. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is de-
signed for indoor use only and it must not be installed where exposed to rain and moisture.
12. Use only installation methods and materials capable of supporting four times the maximum specified
load.
13. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the
risk of electric shock do not perform any servicing other that contained in the operating instructions
unless you are qualified to do so.
14. Only use replacement parts recommended by Pelco.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage Constituting a
risk of electric shock is present within this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
DO NOT OPEN.
REGULATORY NOTICES
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
FCC, Class A (black-white, EIA and CCIR cameras - except auto iris models)
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the in-
struction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to cor-
rect the interference at his own expense.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment
can void your authority to operate this equipment under Federal Communications Commission’s rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Pelco Manual C2410M-H (10/05)
[ 3 ]
FCC, Class B (color, NTSC and PAL cameras - except auto iris models)
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However there is no guarantee that the interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment
can void your authority to operate this equipment under Federal Communications Commission’s rules.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
DESCRIPTION
The 150 Series Camclosure® Integrated Camera System is an in-ceiling dome incorporating a camera
and lens package into a small, discreet, high-security enclosure designed for areas subject to heavy
vandalism.
INSTALLATION
1 Install Back Box
Mounting Directly to Wall or Ceiling
1. Cut a hole 3.5 inches (9 cm) in
diameter in the ceiling or wall
using the adapter plate as a
template.
2. Connect the video cable.
3. Connect the power wires.
•
For 12 VDC, connect the
24 VAC/12 VDC (red) and GND (black)
wires to input power.
•
For 24 VAC, connect the 24 VAC/12 VDC (red)
and 24 VAC (blue) wires to input power.
4. Attach the back box to the wall or ceiling.
[ 4 ] Pelco Manual C2410M-H (10/05)
Mounting to 4S Deep Electrical Box
1. Attach adapter plate to the 4S box
with the two 8-32 x .750-inch
screws.
4S DEEP
ELECTRICAL
BOX
2. Connect the video cable.
WALL OR
CEILING
8.32 X .750 SCREW
(SUPPLIED)
3. Connect the power wires.
ADAPTER PLATE
•
For 12 VDC, connect the
BACK BOX
24 VAC/12 VDC (red) and GND
(black) wires to input power.
For 24 VAC, connect the
01063
8.32 X .375 SCREW
(SUPPLIED)
•
24 VAC/12 VDC (red) and
24 VAC (blue) wires to input power.
4. Attach the back box to the adapter plate
with the four 8-32 x .375-inch screws.
ADAPTER PLATE
Mounting to Ceiling Tile
CEILING TILE
BACK BOX
1. Remove the ceiling tile.
2. Using the adapter plate as a template, cut
a hole 3.5 inches (9 cm) in diameter in the
ceiling tile for the back box. Punch four
screw holes in the ceiling tile.
8-32 X 1.25
MOUNTING
HARDWARE
(SUPPLIED)
01062
3. Attach the back box to the ceiling tile and adapter plate with the four 8-32 x 1.25-inch screws (see
diagram).
4. Replace the ceiling tile.
5. Remove an adjacent ceiling tile and connect the video cable.
6. Connect the power wires.
•
•
For 12 VDC, connect the 24 VAC/12 VDC (red) and GND (black) wires to input power.
For 24 VAC, connect the 24 VAC/12 VDC (red) and 24 VAC (blue) wires to input power.
C A U T I O N
Heater elements could be hot! When camera power is on, use caution when
adjusting the camera. This applies to all models.
2 Install Camera
HEATER
BOARD
1. Some indoor installations do not require a
heater. If the installation does not require a
heater, remove the heater board from the
camera assembly. To remove the heater
apply pressure and press on the corner of
the board.
1092
Pelco Manual C2410M-H (10/05)
[ 5 ]
VIDEO
2. 12 VDC Operation Only - The camera
is set for 24 VAC operation at the
factory. For 12 VDC operation re-
move the jumper from
CONNECTOR
HEATER
CONNECTOR
the 24 VAC position
and install it on the
24 VAC JUMPER
12 VDC JUMPER
12 VDC position.
01065
3. If the heater is installed, plug the
heater connector from the camera into the
mating connector inside the base. Plug the
video connector from the camera into the
mating connector inside the base.
Turn on power to the camera and monitor.
VIDEO
CONNECTOR
HEATER
CONNECTOR
4. If you have a varifocal lens, hold the assembly in
your hand and point the lens toward what you want
to view. Loosen the focal length and focus locking
screws. Adjust according to scene detail. Retighten
the screws.
01068
5. Always make sure the tab on the camera bracket is point-
ing out of the enclosure (away from the ceiling or wall).
Gently squeeze the bracket, place it against the shoulder
inside the back box, and gently release.
Proper camera orientation:
CAMERA BRACKET
TAB ALWAYS POINTS
OUT OF THE
ENCLOSURE
TOP OF
CAMERA
01086
CAMERA BRACKET
TAB ALWAYS POINTS
OUT OF THE
ENCLOSURE
01071
Wall Mounting - The camera bracket
tab points out of the enclosure and the
top of the camera points up towards
the tab.
Ceiling Mounting - The camera
bracket tab points out of the enclo-
sure and the top of the camera is
pointed in the opposite direction.
[ 6 ] Pelco Manual C2410M-H (10/05)
3 Install Dome and Trim Ring
Place the trim ring and dome over the back box. If the
dome has a liner, position the viewing window over the
lens of the camera. Tighten the tamper-resistant screws
with the supplied 1/8-inch hollow screwdriver bit. Note
that the screws are installed at an angle.
01074
ADJUSTMENTS (COLOR CAMERA ONLY)
If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes,
however, adjustments may be necessary.
1. Remove the dome and trim ring using the supplied 1/8-inch hollow screwdriver bit.
2. Adjust the vertical phase, iris level, focus, or switch settings (refer to procedures below).
3. Replace the dome and trim ring.
Vertical Phase (24 VAC Operation Only)
Adjustment is required if there is vertical roll when switching between two cameras.
1. Reverse the 24 VAC connections on one camera. If both cameras are connected to the same trans-
former, this should solve the problem.
2. If reversing the connections does not solve the problem, or if cameras are connected to different trans-
formers, turn the adjustment screw on one camera (while switching as rapidly as possible between the
two camera views) until the switching is clean and there is no vertical roll. If more than two cameras are
out of synchronization with each other, choose one camera and synchronize all others to it.
FIXED LENS
VARIFOCAL LENS
VERTICAL PHASE
ADUSTMENT
VERTICAL
PHASE
ADJUSTMENT
Pelco Manual C2410M-H (10/05)
[ 7 ]
Auto Iris Level Adjustment
If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the level setting to
increase or decrease brightness.
VARIFOCAL LENS
VERTICAL PHASE
ADUSTMENT
Focus Adjustment for Fixed Focal Length Lens with Auto Iris
C A U T I O N
Heater elements could be hot! When camera power is on, use caution when
adjusting the camera.
To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw
on the bottom of the lens.
To remove the heater board:
HEATER
BOARD
1. Disconnect the four-pin heater wiring.
2. Wait for the heater elements to cool if they are hot.
3. Apply pressure and press on the corner of the board.
To adjust the focus:
FOCUS
1. Loosen the locking screw on the bottom of the lens.
2. Move the screw in the slot to bring the picture into focus.
3. Retighten the locking screw.
ADJUSTMENT
SCREW
4. Replace the heater board if it was removed.
5. Reconnect the four-pin heater wiring.
ADJUSTMENT
SLOT
BOTTOM VIEW OF CAMERA WITH
HEATER BOARD REMOVED
[ 8 ] Pelco Manual C2410M-H (10/05)
Switch Settings for Fixed Focal Length Lens with Auto Iris
Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation
(factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions
where there are no bright spots that darken other picture details. Manual backlight compensation is used
in fixed lighting conditions to optimize the picture detail when there are bright spots.
ALC/ELC switch:
Always ALC
Always DC
FACTORY SETTINGS
Y/DC switch:
Auto backlight compensation:
BLC switch OFF
ABL switch ON
ON
OFF
Manual backlight compensation: BLC switch ON
ABL switch OFF
= SWITCH POSITION
Switch Settings for Fixed Focal Length Lens Without Auto Iris
Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation
(factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions
where there are no bright spots that darken other picture details. Manual backlight compensation is used
in fixed lighting conditions to optimize the picture detail when there are bright spots.
ALC/ELC switch:
Always ELC
Not used
FACTORY SETTINGS
Y/DC switch:
Auto backlight compensation:
BLC switch OFF
ABL switch ON
ON
OFF
Manual backlight compensation: BLC switch ON
ABL switch OFF
= SWITCH POSITION
01061
Pelco Manual C2410M-H (10/05)
[ 9 ]
Switch Settings for Varifocal Lens
The high resolution camera with
1
2
3
4
5
6
7
8
AWB Automatic white balance
GAM Gamma function
AGC Automatic gain control
ESC Electronic shutter control
BLC Backlight compensation
FACTORY SETTINGS
varifocal lens and auto iris is
configured at the factory for
optimal performance in lighting
conditions where auto iris is
required. It is also configured with
the shutter speed set at 1/60
(NTSC) or 1/50 (PAL) and manual
gain set at 6 dB.
1
2
3
4
5
6
7
8
FL
Flickerless
OFF
AE
Automatic exposure
= SWITCH POSITION
Not used
01060
For manually setting and locking the white
balance
Place a white background in front of camera and
turn off switch 1.
For gamma correction
WARNING Do not change the shutter
speed unless you understand how
changing the settings will affect the
scene detail.
Switch to accurately reproduce scene brightness;
when turned on, y = 0.6, and when turned off,
y = 1.0.
For automatic exposure
Switch Number and Position
Shutter
Speed
Turn on switch 7, and then turn on/off switch 3
for AGC, switch 4 for electronic shutter control,
switch 5 for backlight compensation, and switch
6 for flickerless motion.
7
6
5
4
1/60 (NTSC)
1/50 (PAL)
1/100
1/250
1/500
1/1000
1/2000
1/4000
1/10000
On
On
On
Off
On
Off
On
Off
On
Off
On
Off
Off
On
On
Off
Off
On
On
On
Off
Off
Off
Off
Off
For manual exposure and to enable auto iris
Turn off switch 7; set switch 3 on to increase the
gain by 6 dB or off to increase the gain by 18 dB;
set switches 4, 5, and 6 for the desired shutter
speed.
[ 10 ] Pelco Manual C2410M-H (10/05)
SPECIFICATIONS
General
Operating Temperature:
-50° to 122°F (-46° to 50°C)
De-ices to 25°F (-4°C)
Pan/Tilt
Adjustment:
Construction:
Finish:
Manual; 360° pan; 180° tilt
Aluminum with steel camera mounting bracket and polycarbonate dome
White polyester powder coat trim ring with charcoal gray back box
Dimensions
Above Ceiling:
1.75 (H) x 3.50 (W) inches
(4.45 x 8.89 cm)
Below Ceiling:
2.42 (H) x 5.48 (W) inches
(6.15 x 13.90 cm)
Bubble:
3.75-inch diameter
Environment:
Low temperature, indoor/outdoor, suitable for use in environmental air
handling spaces
1.70 lb (0.77 kg)
Weight:
Electrical
Input Voltage:
Power Consumption:
Video Connector:
12 VDC or 24 VAC, ±10%
13 watts or less
BNC
(Design and product specifications subject to change without notice.)
This equipment contains electrical or electronic components that must be recycled properly to comply
with directive 2002/96/ec of the european union regarding the disposal of waste electrical and electronic
equipment (weee). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual #
C2410M
C2410M
C2410M-A
C2410M-B
C2410M-C
C2410M-D
C2410M-E
C2410M-F
Date
11/99
1/00
1/00
7/00
1/01
7/01
7/02
5/03
Comments
Original version.
Revised installation instructions. Added FCC notices.
Added varifocal lens. Changed format.
Added information on dome liner.
Added heater element caution.
Camera module redesigned, reference ECO 1-7054/7055/7056.
Added instructions for fixed lens with auto iris.
Revised Installation instructions – bracket and camera assembled at factory. Added iris
level adjustment for fixed lens with auto iris.
Added to certifications that all models are suitable for use in environmental air handling
spaces.
C2410M-G
C2410M-H
1/04
10/05
Revised drawings showing vertical phase and iris level adjustments. Revised switch-setting
descriptions for varifocal lens. Added WEEE statement.
Pelco Manual C2410M-H (10/05)
[ 11 ]
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the
date of shipment.
Exceptions to this warranty are as noted below:
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2,
CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.
•
•
•
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
Two years (except lamp and color wheel) on Digital Light Processing (DLP™) displays. The lamp and color wheel will be covered for a pe-
riod of 90 days. The air filter is not covered under warranty.
•
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-
based video products.months on DX Series digital video recorders, NVR300 Series network video recorders, Endura™ Series distributed
network-based video products, and TW3000 Series twisted pair transmission products.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan
modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be
sent freight
will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Prod-
ucts. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liabil-
ity, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any
special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation
from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number
(RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a
written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one
of the following
If the goods are to be sent by a
COURIER SERVICE, send the goods to:
Pelco
If the goods are to be sent by a FREIGHT
FORWARDER, send the goods to:
Pelco c/o Expeditors
3500 Pelco Way
Clovis, CA 93612-5699 USA
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
©Copyright 2005, Pelco.
All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc.
|