®
Installation/Operation
Camclosure® Lens Packs
C1971M-D (1/03)
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120
Color Camera
When replacing a lens on a color camera, change
the lens mount and lens.
REMOVE LENS
MOUNT & LENS
UNSCREW
1. Unscrew the two Phillips screws on the
sides of the lens mount. Do not discard
the screws as you will need them to
secure the new mount. Lift and remove
the lens mount and lens.
UNSCREW
2. The new lens mount and lens are shipped
unassembled. Mount the lens onto the lens
mount by carefully threading it clockwise.
MOUNT LENS
(CLOCKWISE)
3. Install the new lens mount assembly. Secure it
with the two Phillips screws previously removed
in step 1.
DO NOT OVER-
TIGHTEN SET
SCREW
4. Remove the dust cover from the lens.
ADJUST LENS
(CLOCKWISE)
REMOVE
DUST
COVER
5. Lens Adjustment – Turn the lens clock-
wise/counterclockwise until the picture on
the monitor is in focus. Carefully tighten
the set screw. Do not over-tighten.
ICS200 SERIES
Camera Installation (ICS200
and ICS300 Series Only)
To prevent damage to the camera or lens of
an ICS200 or ICS300 Series Camclosure
integrated camera system, the camera must
be installed in the proper hole of the mount-
ing bracket. If the camera is not installed in
the correct hole, the window of the enclosure
may be forced against the lens.
ICS300 SERIES
Refer to the illustrations for which mounting
hole to use to install the camera.
Pelco Manual C1971M-D (1/03)
[ 3 ]
SPECIFICATIONS
Focal Length
Format Size
Relative Aperture (F)
Iris
Horizontal Angle of View
2.9 mm
1/3-inch
2.0
Fixed
90°
3.6 mm
1/3-inch
2.0
Fixed
74°
6 mm
1/3-inch
1.8
Fixed
42°
8 mm
1/3-inch
2.5
Fixed
32°
12 mm
1/3-inch
2.5
Fixed
21°
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
•
•
•
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video
products.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
3500 Pelco Way
Clovis, CA 93612-5699 USA
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco. ©Copyright 2003, Pelco. All rights reserved.
ꢀ
REVISION HISTORY
Manual #
C1971M
C1971M-A
C1971M-B
Date
3/00
4/00
7/00
Comments
Original version.
Revised specifications.
Revised manual to include all series of Camclosure integrated camera systems.
Revised specifications.
Added 3.6 mm lens.
C1971M-C
C1971M-D
3/02
1/03
Added camera installation instructions for ICS200 and ICS300 Series.
|